DNR Super High Resolution

Day & Night Color Camera

3-AXIS INDOOR DOME CAMERA

WARNINGS AND CAUTIONS:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR

MOISTURE. DO NOT INSERT ANY METALLIC OBJECTS THROUGH THE VENTILATION GRILLS OR

OTHER OPENINGS ON THE EQUIPMENT.

CAUTION:

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER(OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

EXPLANATION OF GRAPHICAL SYMBOLS

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

PRECAUTIONS

Safety ----------------------------------------- Installation -----------------------------------

Should any liquid or solid object fall into the cabinet, unplug the unit and have it checked by the qualified personnel before operating it any further.

Do not install the unit in an extremely hot or humid place or in a place subject to excessive dust, mechanical vibration.

Unplug the unit from the wall oulet if it is not going to be used for several days or more. To disconnect the cord, pull it out by the plug. Never pull the cord itself.

Allow adequate air circulation to prevent internal heat build-up. Do not place the unit on surfaces (rugs, blankets, etc.) or near materials(curtains, draperies) that may block the ventilation holes.

Height and vertical linearity controls located at the rear panel are for special adjustments by qualified personnel only.

The unit is not designed to be waterproof.

Exposure to rain or water may damage the unit.

Cleaning --------------------------------------

Clean the unit with a slightly damp soft cloth.

Use a mild household detergent. Never use strong solvents such as thinner or benzine as they might damage the finish of the unit.

Retain the original carton and packing materials for safe transport of this unit in the future.

ii

FCC COMPLIANCE STATEMENT

FCC INFORMATION :

THIS EQUIPMENT HAS BEEN TESTED

AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL

DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE

LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION

AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS

OPERATED IN A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT

GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY

ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH

THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL INTERFERENCE

TO RADIO COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN

A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL

INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO

CORRECT THE INTERFERENCE AT HIS OWN EXPENSE.

CAUTION :

CHANGES OR MODIFICATIONS NOT EXPRESSLY

APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE

COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.

THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN

ICES-003.

NORME NMB-003 DU CANADA.

CE COMPLIANCE STATEMENT

WARNING

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

iii

IMPORTANT SAFEGUARDS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the

manufacturer's instructions.

8. Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

product heat..

9. Do not defeat the safety purpose of the polarized or grounding-type

Plug. A polarized plug has two blades with one wider than the other.

A grounding type plug has two blades and a third grounding prong.

The wide blade or the third prong are provided for your safety. If the

provided plug does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point where

thy exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Unplug this apparatus during lightning storms or when unused for

long periods of time.

13. Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way, such

as power-supply cord or plug is damaged, liquid has been spilled or

objects have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally, or has been

dropped.

14. CAUTION - THESE SERVICING INSTRUCTIONS ARE FOR USE

BY QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE

RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING

OTHER THAN THAT CONTAINED IN THE OPERATING

INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO.

15. Use Certified/Listed Class 2 power source only.

iv

INTRODUCTION

The camera provides high-quality images using SONY 1/3" CCD and digital signal processing LSIs.

Features:

1/3" Super HADII CCD for an image of high sensitivity

Digital Wide Dynamic Range

Excellent picture quality

(Xtended Dynamic Range)

560 lines of resolution

0.25 Lux(Color), 0.01 Lux(B/W)@ F1.2 Sensitivity

Auto electronic shutter [1/60(1/50) ~ 1/100,000] and manual electronic shutter modes

OSD (On Screen Display)

Auto and manual white balance modes

Selectable BLC Zone

HSBLC

3D-Digital Noise Reduction

Day&Night (Auto/Manual)

Privacy Zone 8 point, Motion Detection 4 Point

SHARPNESS, D-ZOOM, NEGA/POSI, MIRROR, V FLIP, ROTATION, FREEZE

AGC (Auto Gain Control)

VIDEO OUT(BNC)

Internal/AC line lock

2.6~6mm , 4-9mm, 2.8~12mm, 6~50mm D&N Auto Iris Lens.

Operates in 12VDC or 24VAC

Use Certified / Listed Class 2 power source only.

IMPORTANT : The user of this camera is responsible for checking and complying with local, state, and federal laws and statutes concerning the recording and monitoring of audio signals.

CAUTION: Before plugging in, please check the label to make sure you have the proper rating.

CAMERA CONNECTIONS

3

1

1. Lens : Allows a wide area to be monitored.

1

2

2. Color Lead Wire & Color Display Label

COLOR

RED

WHITE

YELLOW

GRAY

BLACK&WHITE

BLACK

DESCRIPTION

AC24V/DC12V

AC24V/DC12V

ALARM OUT

DN EXT-IN

DN EXT-OUT

GND

REMINDER:

Never aim the camera directly into the sun.

3. Power : power source from a DC 12V / AC24V +/- 10%

Use Certified/Listed Class 2 power supply transformer only.

*If use DC 12V / AC24V power adaptor, use the power consumption 5W over.

4. Video : BNC connector used to connect the camera to a monitor, switcher, etc.

5. DAY&NIGHT I/O Terminals

To select Day/Night mode using external equipment, connect control lines to the appropriate terminals.

DAY&NIGHT OUTPUT

It is the function that can turn on external IR LED Lamp by detecting the sensitivity on the AGC level when the D&N mode is set "AUTO" on the OSD menu of the camera.

DN EXT-OUT

GND

5V/10mA : IR LED ON(NIGHT)

0V : IR LED OFF(DAY)

DAY&NIGHT EXTERNAL INPUT

It is the function that can be switched to DAY Mode or NIGHT Mode by receiving the

D&N on/off signal from external light sensor or IR LED LAMP. When D&N Mode is set

"External" on the OSD menu of the camera.

GND

DN EXT-IN

Open contact : DAY

Close contact : NIGHT

6. ALARM OUT

Motion detection signals are output through this port. (On High (5V))

2

PACKAGE CONTENTS

The package contains the following.

Camera in Housing

Instruction Manual (This Document)

Accessory Kit for Installing

Drilling guide label

1

1

1

1

INSTALLATION

1. Make mounting holes and cable hole in the place (ceiling or wall) to which this dome

camera is installed using the Drilling guide label.

Liner

Dome body

2. To remove dome cover, turn the dome body counterclockwise until locators reach end of

travel and pull off. Push the liner on the sides where the patterns are put in the teeth of a

comb and pull it out.

WALL

Drilling Guide Label

Dril ling

Po sitio n(P

A5)

Plastic anchor

Screw Tapping (M6)

3

MOUNTING HOUSING TO

AN ELECTRICAL BACK BOX

The housing can also be mounted on a 4s electrical box.

Electrical box

Torx screws

UNC 8-32 x 0.75

3. Attach the housing to the ceiling using suitable fasteners, M6x35 tapping screws are

supplied only use if they are suitable. Turn the housing to right direction about 16 degrees

to lock in place.

4. The assembly of the dome body and liner is in reverse order of disassembly.

Finally, lock dome body with locking screw(M3X5) from the accessory kit.

OPERATING CAMERA

3

4

1

2

5

6

Enter Button

Up

Down

Left

Right

Spot Video Out

6

1

2 3 4 5

4

STRUCTURE OF THE SETUP MENU

<SETUP>

1.LENS

2.EXPOSURE

3.WHITE BAL

4.DAY NIGHT

5.3DNR

6.SPECIAL

7.ADJUST

8.RESET

9.EXIT

<LENS>

DC

<EXPOSURE>

SHUTTER

BRIGHTNESS

AGC

SENSE-UP

BLC

D-WDR

RETURN

<WHITE BAL>

AWB

AWC -> SET

MANUAL

INDOOR

OUTDOOR

ATW

<DAY NIGHT>

AUTO

EXT

B/W

COLOR

<3DNR>

LEVEL

RETURN

<SPECIAL>

CAM TITLE

D-EFFECT

MOTION

PRIVACY

SYNC

LANGUAGE

RETURN

<ADJUST>

SHARPNESS

BLUE

RED

RETURN

5

<RESET>

FACTORY

RETURN

LENS (Selection)

This function is used to adjust the brightness of the screen.

1. When the SETUP menu is displayed on the screen, please position the arrow to point to

'LENS' by using the UP and DOWN buttons.

2. Please select the type of the lens you wish to use by pressing the LEFT or RIGHT button.

► 1. LENS DC

2. EXPOSURE

3. WHITE BAL AWB

4. DAY NIGHT AUTO

5. 3DNR ON

6. SPECIAL

7. ADJUST

8. RESET

9. EXIT

LENS

► BRIGHTNESS

IIIIIIIIIIIIIIIIII

50

RETURN RET

Note The brightness of the screen can be adjusted in DC mode.

The brightness can be adjusted within the range of 0 ~ 100.

The optimum level of brightness for the user can be achieved by adjustment.

EXPOSURE

The EXPOSURE menu is used to set the automatic light control method for this camera.

1) SHUTTER

2) BRIGHTNESS

3) AGC

4) SENSE-UP

5) BLC

6) D-WDR

Select the shutter mode.(1/60(50), FLK~ 1/100,000 sec, x2 ~ x256)

Can be changed while in shutter mode.

Adjust BRIGHTNESS level (0 ~ 100)

Can be adjusted while in manual lens mode.

Auto gain control (OFF / LOW / MIDDLE / HIGH)

Use under very low light condition for full color surveillance.

Select maximum Low-Shutter value. (x2 ~ x256)

Sharpens subjects with backlight.(OFF / BLC / HBLC)

Digital Wide dynamic range (Xtended Dynamic Range)

OFF / INDOOR / OUTDOOR

►

1. LENS DC

2. EXPOSURE

3. WHITE BAL AWB

4. DAY NIGHT AUTO

5. 3DNR ON

6. SPECIAL

7. ADJUST

8. RESET

9. EXIT

<BLC MODE>

EXPOSURE

►

SHUTTER 1/60

BRIGHTNESS

IIIIIIIIIIIIIIIIII

50

AGC HIGH

SENSE-UP AUTO

BLC BLC

D-WDR OFF

RETURN RET

BLC

► GAIN MIDDLE

DEFAULT

LEFT/RIGHT

IIIIIIIIIIIIIIIIII

2

WIDTH

IIIIIIIIIIIIIIIIII

4

TOP/BOTTOM

IIIIIIIIIIIIIIIIII

3

HEIGHT

IIIIIIIIIIIIIIIIII

3

RETURN RET

6

WHITE BAL

The screen color can be adjusted by using the WHITE BALANCE function.

1) AWB

2) AWC -> SET

3) MANUAL

4) INDOOR

5) OUTDOOR

6) ATW

Wide range auto white balance mode.

Please press the ENTER button while the camera is directed at a piece of while paper to obtain the optimum state under current illumination. if the environment including the light source is changed, you have to adjust the while balance again.

Manual mode. User can change R and B Gain manually.

Set the color temperature to 3200 K

Set the color temperature to 6300 K

O

O

►

1. LENS DC

2. EXPOSURE

3. WHITE BAL MANUAL

4. DAY NIGHT AUTO

5. 3DNR ON

6. SPECIAL

7. ADJUST

8. RESET

9. EXIT

<WHITE BAL MANUAL MODE>

WHITE BAL MANUAL

► BLUE

IIIIIIIIIIIIIIIIII

50

RED

IIIIIIIIIIIIIIIIII

50

RETURN RET

DAY NIGHT

The DAY/NIGHT menu is used to configure the day and night related setting for this camera.

This camera can turn the IR(infrared)filter on or off.

Mode : AUTO / EXT / B/W / COLOR

►

1. LENS DC

2. EXPOSURE

3. WHITE BAL AWB

4. DAY NIGHT AUTO

5. 3DNR ON

6. SPECIAL

7. ADJUST

8. RESET

9. EXIT

<DAY/NIGHT AUTO MODE>

DAY NIGHT AUTO

► DELAY

IIIIIIIIIIIIIIIIII

5

S-LEVEL

IIIIIIIIIIIIIIIIII

50

E-LEVEL

IIIIIIIIIIIIIIIIII

30

RETURN RET

►

1. LENS DC

2. EXPOSURE

3. WHITE BAL AWB

4. DAY NIGHT B/W

5. 3DNR ON

6. SPECIAL

7. ADJUST

8. RESET

9. EXIT

<DAY/NIGHT B/W MODE>

DAY NIGHT B/W

► BURST OFF

RETURN RET

3DNR (Digital Noise Reduction)

You can configure the DNR(Digital Noise Reduction) related settings. if you press the Setup switch when ON is selected in 3DNR, the corresponding screen appears.

7

►

1. LENS DC

2. EXPOSURE

3. WHITE BAL AWB

4. DAY NIGHT AUTO

5. 3DNR ON

6. SPECIAL

7. ADJUST

8. RESET

9. EXIT

3DNR

► LEVEL

IIIIIIIIIIIIIIIIII

50

RETURN RET

SPECIAL

1) CAM TITLE

A

B

C

CAM TITLE

0123456789

ABCDEFGHIJK

LMNOPQRSTUV

WXYZ ►→←↑↓()

‾–_ ▌/ = & : ~ ‚ "

←→ CLR POS END

A. CAM TITLE

B. Character Table

C. Command Line

← : Move to left

→ : Move to right

CLR : Erase all characters

POS : Move the position of title

END : Save and End

2) D-EFFECT

FREEZE

MIRROR

D-ZOOM

GAMMA Adjust the luminance (0.05~1.00)

NEGA / POSI

Select the real or still mode.

Reverse the screen in 3 modes selection.

(OFF / MIRROR / V FLIP / ROTATION)

D-Zoom (x2~x32) / Adjust PAN / TITL

Select the negative or positive mode.

3) MOTION

AREA SELECT

LEFT/RIGHT

Select MD area number.

AREA DISPLAY Select MD ON/OFF

Adjust the location of the MD area with boundary LEFT and

RIGHT.

WIDTH Adjust width of MD area

TOP/BOTTOM

SENSITIVITY

Adjust the location of the MD area with boundary TOP and BOTTOM

HEIGHT Adjust height of MD area

Adjust sensitivity of MD area.(0~40)

MOTION VIEW The screen displays with green dots. When a motion is detected

in the selected area, the green dots are displayed on the screen.

►

1. LENS DC

2. EXPOSURE

3. WHITE BAL AWB

4. DAY NIGHT AUTO

5. 3DNR ON

6. SPECIAL

7. ADJUST

8. RESET

9. EXIT

SPECIAL

►

1.CAM TITLE ON

2.D-EFFECT

3.MOTION ON

4.PRIVACY OFF

5. SYNC INT

6.LANGUAGE ENGLISH

7.RETURN RET

8

►

MOTION

AREA SELECT AREA1

AREA DISPLAY ON

LEFT/RIGHT

IIIIIIIIIIIIIIIIII

8

WIDTH

IIIIIIIIIIIIIIIIII

32

TOP/BOTTOM

IIIIIIIIIIIIIIIIII

4

HEIGHT

IIIIIIIIIIIIIIIIII

24

SENSITIVITY

IIIIIIIIIIIIIIIIII

40

MOTION VIEW OFF

4) PRIVACY

AREA SELECT

AREA DISPLAY

LEFT/RIGHT

Select MASK area number.

Select MASK ON/OFF

Adjust the location of the MASK area with boundary LEFT and RIGHT

WIDTH Adjust width of MASK area

TOP/BOTTOM Adjust the location of the MASK area with boundary

TOP and BOTTOM.

HEIGHT Adjust height of MASK area

COLOR Select MASK color. (0~15)

►

1. LENS DC

2. EXPOSURE

3. WHITE BAL AWB

4. DAY NIGHT AUTO

5. 3DNR ON

6. SPECIAL

7. ADJUST

8. RESET

9. EXIT

<PRIVACY MODE>

SPECIAL

►

1.CAM TITLE ON

2.D-EFFECT

3.MOTION OFF

4.PRIVACY ON

5. SYNC INT

6.LANGUAGE ENGLISH

7.RETURN RET

►

PRIVACY

AREA SELECT AREA1

AREA DISPLAY ON

LEFT/RIGHT

IIIIIIIIIIIIIIIIII

8

WIDTH

IIIIIIIIIIIIIIIIII

20

TOP/BOTTOM

IIIIIIIIIIIIIIIIII

10

HEIGHT

IIIIIIIIIIIIIIIIII

35

COLOR

IIIIIIIIIIIIIIIIII

0

RETURN RET

5) SYNC

INT

L/L

Select Internal or Line Lock mode.

This mode is necessary for using the internal synchronization.

This mode is necessary for the operation of multi camera because it synchronizes the camera phase by using the external signal

(AC Signal).

Sync phase is adjustable in line lock mode.

PHASE

6) LANGUAGE You can change the OSD language using the LEFT/RIGHT

Setup switch.

ADJUST

1) SHARPNESS

2) BLUE

3) RED

Can be adjusted SHARPNESS of outlines.(0~31)

Adjust B-GAIN value.(0~100)

Adjust R-GAIN value.(0~100)

RESET

1) FACTORY Returns to the level which was set by the manufacturer for shipment.

EXIT

1) EXIT Saves all the setting menus and then exits.

9

LENS ADJUSTMENT (OPTIONAL VARIFOCAL LENS)

Field of view: Adjust setting from Telephoto (T) to wide (W) field of View.

Focus: Adjust lens focus from near

(N) to infinity ( ).

Adjust Focus

Adjust Angular Field View

DC AUTO IRIS LENS

2.6~6mm

Focal Length 2.6-6.0mm 5%

Aperture Ratio 1 : 1.6 5%

Angular

Field of View

DIAGONAL

2.6mm : 134.6

o

6mm : 59.2

o

4-9mm

1/3" CCD

2.8~12mm

(Aspherical )

1/3" CCD

4.0-9.0mm 5% 2.8-12mm 5%

1 : 1.6 5%

DIAGONAL

4mm : 92.4

9mm : 39.2

o o

1 : 1.4 5%

2.8mm : 119.9

12mm : 28.8

o o

6-50mm

1/3" CCD

6.0-50mm 5%

1 : 1.6 6.9%

DIAGONAL

6mm : 58.6

50mm : 7.1

o o

LENS

Black Control ( - )

White Control ( + )

Red Drive ( + )

Green Drive ( - )

LENS

Yellow

Brown IR filter out ( + )

LENS

Brown

Red Damper ( + )

Yellow

Orange

Damper ( - )

Drive ( + )

Drive ( - )

10

SPECIFICATIONS

Power

General

Connector

& etc.

MODEL

Power source

Power consumption

Image sensor

Total pixels

Scanning system

Scanning frequency

Sync. system

Resolution

Min. illumination

Video output

S/N ratio

DNR

(Digital Noise Reduction)

D-WDR

(Digital Wide Dynamic Range)

N

C

F

U

BLC

(Back Light Composite)

Day & Night (True D/N)

MD (Motion Detection)

I

T

O

N

SENSE-UP

(Low Shutter Speed)

PM (Privacy Masking)

WB (White Balance)

AGC (Auto Gain Control)

Electronic Shutter Speed

Sharpness

Flip

Effect

Setup Method

OSD Language

Power input

Video output

External I/O Terminals

Lens mount

Lens

Operating temperature

Operating humidity

External Dimension

Weight

NTSC

On / Off (Adjustable Gain)

On(Indoor / Outdoor) / Off

PAL

1/3" SONY Super HADII CCD

811(H) x 508(V)

3.0 Watts

2:1 interlace

15.734KHz(H) x 59.94Hz(V)

795(H) x 596(V)

15.625KHz(H) x 50Hz(V)

Internal / Line lock

560 TV lines

Color(0.25 Lux), B/W(0.01 Lux) (SENS UP : OFF)

1.0 Vp-p (75 ohm, composite)

50dB (AGC OFF)

BLC / HSBLC / OFF Adjustable Size & Gain

Color / B/W / Auto (Filter auto change) / EXT

On / Off (4 Programmable zone)

Auto / Off (Selectable limit 2X ~ 256X)

On / Off (8 Programmable zone)

AWB / ATW / AWC / Manual / Indoor / Outdoor

On( Low / Middle / High) / Off

Auto / Flickerless / Manual (256X, 1/60 ~ 1/ 100,000)

On / Off (Level adjustable)

Horizontal / Vertical / Rotate

D-Zoom x32(Pan / Tilt) / Nega / Freeze

OSD setup menu

English / Korean / Japanese

Terminal block

BNC connector

Alarm output, Day & Night input / output

Fixed mount

2.6~6mm , 4-9mm, 2.8~12mm, 6~50mm D/N Vari-focal (DC AI)

5

0 ~ 96% (non-condencing)

146 x 113 mm (Bubble Diameter Ø100)

450g

11

EXTERNAL DIMENSION

Dimensions

145.6

113

59

Window Size

Cable Entry

Weight - Unit:

Shipping:

0.1 in. (2.5mm thick), impact-resistant P.C (LEXAN)

3.93 in. (10cm) diameter

One 1" opening holes

Unit: mm

0.99 lb. (0.45kg)

1.41 lb. (0.64 kg)

Super High Resolution

Day & Night Color Camera

50302581A