24" (61 cm) and 27" (69 cm) Electric Washer/Dryer

24" (61 cm) and 27" (69 cm) Electric Washer/Dryer
Submittal Review
Project Name:
Pullman
Job #:
1825C
The
information
contained
within
this
has been
Eichberg
Construction,
Inc. hereby
states
thatsubmittal
we have reviewed
the
informationchecked
submitted and
and has
found it to be
in compliance
with the
generally
coordinated
with
the requirements
Contract
Documents,
where
otherwise noted by us, and
of
the work
and theexcept
contract
documents.
approve it for further review by the Architect / Engineer.
Submittal #
113100-001
Architect / Engineer:
R2L
Drawing Reference:
24" (61 cm) and 27" (69 cm)
Electric Washer/Dryer
Reviewed By:
EEA
Spec. Section:
113100
ADU
Subcontractor / Vendor:
Other Reference:
Date:
4/8/16
PRODUCT MODEL NUMBERS
WET4024E, WET4027E
Dimensions/Clearances - 24" (61 cm)
Front View
Side View
23 7/8"
(606 mm)
35 7/8"
(911 mm)
20 1/2"
(521 mm)
70 3/4"
(1797 mm)
653/4"
(1670 mm)
70 3/4"
(1797 mm)
30 3/4"
(781 mm)
37"
(940 mm)
1"
(25 mm)
26 7/8"
(683 mm)
1"
(25 mm)
Back View
23 7/8"
(606 mm)
111/2"
(292 mm)
70 3/4"
(1797 mm)
14"
(356 mm)
43 1/2"
(1105 mm)
34 1/4"
(870 mm)
27 1/2"
26"
(699 mm)
(660 mm)
1"
(25 mm)
W10761048A
05/2015
Dimensions/Clearances - 27" ( 69 cm)
Front View
Side View
271/4"
(692 mm)
58 7/8"
(1495 mm)
713/4"
(1822 mm)
26"
(660 mm)
653/4"
(1670 mm)
713/4"
(1822 mm)
321/8"
(816 mm)
34"
(864 mm)
32"
(813 mm)
1"
(25 mm)
Back View
271/4"
(692 mm)
11"
(279 mm)
713/4"
(1822 mm)
14"
(356 mm)
411/4"
(1,048 mm) 351/4"
(895 mm)
261/2"
25"
(673 mm)
(635 mm)
1"
(25 mm)
2
1"
(25 mm)
Clearances
Side Clearances
(recommended/minimum)
Front/Back/Top
(recommended/minimum)
Recessed area or closet installation
12"
(305 mm)
48 in.2
(310 cm2)
Front
View
3"
(76 mm)
Closet
door
3"
(76 mm)
24 in.
(155 cm2)
2
1"/0"
(25 mm/0 mm)
1"/0"
(25 mm/0 mm)
1"
(25 mm)
(Closet)
5"
(127 mm)
ELECTRICAL REQUIREMENTS
To supply the required 3 or 4 wire, single phase, 120/240 volt, 60 Hz., AC only electrical supply (or 3 or 4 wire, 120/208 volt electrical
supply, if specified on the serial/rating plate) on a separate 30-amp circuit, fused on both sides of the line. A time-delay fuse or circuit
breaker is recommended. Connect to an individual branch circuit.
The “Vent System Chart” provides venting requirements that
will help achieve best drying performance.
VENTING REQUIREMENTS
Exhaust venting: Exhaust your dryer to the outside. 4" (102 mm)
diameter vent is required. Rigid or flexible metal exhaust vent
must be used. Do not use plastic or metal foil vet. Exhaust hood
must be at least 12" (305 mm) from the ground or any object that
may be in the path of the exhaust.
Recommended Styles:
Louvered hood
Acceptable Style:
Box hood
Angled hood
Vent System Chart, 24" Models
Number of
90° turns
or elbows
Type
of vent
Box/louvered
hoods
Angled
hoods
0
Rigid metal
43 ft. (13.1 m)
36 ft. (11.0 m)
1
Rigid metal
33 ft. (10.1 m)
26 ft. (7.9 m)
2
Rigid metal
23 ft. (7.0 m)
16 ft. (4.9 m)
Vent System Chart, 27" Models
Number of
90° turns
or elbows
Type
of vent
Box/louvered
hoods
Angled
hoods
0
Rigid metal
37 ft. (11.3 m)
35 ft. (10.7 m)
1
Rigid metal
32 ft. (9.7 m)
27 ft. (8.2 m)
2
Rigid metal
23 ft. (7.0 m)
19 ft. (5.8 m)
NOTE: Side exhaust installations have a 90º turn inside the
dryer. To determine maximum exhaust length, add one 90º
turn to the chart.
3
DRAIN SYSTEM
Drain system can be installed using a floor drain, wall standpipe,
floor standpipe, or laundry tub. Select method you need.
Floor standpipe drain system
Minimum diameter for a standpipe drain: 2" (51 mm). Minimum
carry-away capacity: 17 gal. (64 L) per minute. Top of standpipe
must be at least 39" (990 mm) high; install no higher than 96"
(2.4 m) from bottom of washer/dryer. If you must install higher
than 96" (2.4 m), you will need a sump pump system.
Floor drain system
Floor drain system requires a Siphon Break Kit (Part Number
285834), 2 Connector Kits (Part Number 285385), and an
Extension Drain Hose (Part Number 285863) that may be
purchased separately. See “Use and Care Guide” for ordering
details. Minimum siphon break: 28" (710 mm) from bottom of
washer/dryer. (Additional hoses may be needed.)
Laundry tub drain system
Wall standpipe drain system
See requirements for floor standpipe drain system.
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Minimum capacity: 20 gal. (76 L). Top of laundry tub must be
at least 39" (990 mm) above floor; install no higher than 96"
(2.4 m) from bottom of washer/dryer.
IMPORTANT: To avoid siphoning, no more than 4.5" (113 mm)
of drain hose should be inside standpipe or below the top of
wash tub. Secure drain hose with shipping strap.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
30" (76.2 cm) Freestanding Electric Range
PRODUCT MODEL NUMBERS
WEC530H0D
PRODUCT DIMENSIONS
WEE730H0D
WEE760H0D
Electrical: If codes permit and a separate ground wire is used, it is
recommended that a qualified electrical installer determine that the ground
path and wire gauge are in accordance with local codes.
Do not use an extension cord.
To properly install your range, you must determine the type of electrical
connection you will be using and follow the instructions provided for it
here.
●
Range must be connected to the proper electrical voltage and frequency
as specified on the model/serial number rating plate. The model/serial
rating plate is located behind the oven door on the top right-hand side of
the oven frame.
●
This range is manufactured with the neutral terminal connected to the
cabinet. Use a 3-wire, UL listed, 40- or 50-amp power supply cord
(pigtail) (see following Range Rating chart). If local codes do not permit
ground through the neutral, use a 4-wire power supply cord rated at
250 volts, 40 or 50 amps and investigated for use with ranges.
Range Rating*
Specified Rating of
Power Supply Cord Kit
and Circuit Protection
120/240 Volts
120/208 Volts
Amps
8.8 - 16.5 KW
16.6 - 22.5 KW
7.8 - 12.5 KW
12.6 - 18.5 KW
40 or 50**
50
*The NEC calculated load is less than the total connected load listed on
the model/serial rating plate.
**If connecting to a 50-amp circuit, use a 50-amp rated cord with
kit. For 50-amp rated cord kits, use kits that specify use with a
nominal 1³⁄₈" (34.9 mm) diameter connection opening.
● A circuit breaker is recommended.
This manual covers several models. Your model may appear different from
the models depicted. Dimensions given are maximum dimensions across all
models.
B
C
A
D
E
F
A. 1³⁄₁₆" (3.0 cm) height from
cooktop to top of vent
B. 29⁷⁄₈" (75.9 cm)
C. Model/serial number plate
(located behind the oven door on
the top right-hand side of the
oven frame)
D. 36" (91.4 cm) height to top of
cooktop edge with leveling legs
screwed all the way in*
E. 28⁵⁄₁₆" (71.9 cm) max. depth
from front of console to
back of range.
F. 28⁷⁄₈" (73.3 cm) max. depth
from handle to back of
range.
IMPORTANT: Range must be level after installation. Follow the instructions
in the “Level Range” section. Using the cooktop as a reference for leveling
the range is not recommended.
**Range can be raised approximately 1" (2.5 cm) by adjusting the leveling
legs.
Page 1 of 2
Because Whirlpool Corporation policy includes a continuous commitment to improve our
products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. W10665255B
9/30/14
CABINET OPENING DIMENSIONS
Cabinet opening dimensions shown are for 25" (64.0 cm) countertop depth, 24" (61.0 cm) base cabinet depth and 36" (91.4 cm) countertop height.
IMPORTANT: If installing a range hood or microwave hood combination above the range, follow the range hood or microwave hood combination
installation instructions for dimensional clearances above the cooktop surface.
Range may be installed next to combustible walls with zero clearance.
NOTE: When installed in a slide-in cutout, the front of oven door may protrude beyond the base cabinet.
Slide-in Cutout
Freestanding cutout
D
B
D
B
C
C
L
A
A
E
E
K
K
G
G
H
I
F
H
I
F
J
I
A. 18" (45.7 cm) upper side cabinet to countertop
B. 13" (33 cm) max. upper cabinet depth
C. 30" (76.2 cm) min. opening width
D. For minimum clearance to top of cooktop, see NOTE*.
E. In U.S.A.: 30" (76.2 cm) min. opening width
In Canada: 31" (78.7 cm) min. opening width
F. The shaded area is recommended for installation of grounded
outlet.
G. 13¹⁄₈" (33.3 cm)
H. 7¹¹⁄₁₆" (19.5 cm)
I. 4¹³⁄₁₆" (12.2 cm)
J. 3¹¹⁄₁₆" (9.4 cm) or measurement of L, whichever is greater
K. Cabinet door or hinges should not extend into the cutout.
L. Remaining counter depth should not exceed 2¼" (5.7 cm)
J
I
A. 18" (45.7 cm) upper side cabinet to countertop
B. 13" (33 cm) max. upper cabinet depth
C. 30" (76.2 cm) min. opening width
D. For minimum clearance to top of cooktop, see NOTE*.
E. In U.S.A.: 30" (76.2 cm) min. opening width
In Canada: 31" (78.7 cm) min. opening width
F. The shaded area is recommended for installation of grounded
outlet.
G. 13¹⁄₈" (33.3 cm)
H. 7¹¹⁄₁₆" (19.5 cm)
I. 4¹³⁄₁₆" (12.2 cm)
J. 3¹¹⁄₁₆" (9.4 cm)
K. Cabinet door or hinges should not extend into the cutout.
*NOTE: 24" (61.0 cm) minimum when bottom of wood or metal cabinet is shielded by not less than ¹⁄₄" (0.64 cm) flame retardant millboard covered with
not less than No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper.
30" (76.2 cm) minimum clearance between the top of the cooking platform and the bottom of an uncovered wood or metal cabinet.
Page 2 of 2
Because Whirlpool Corporation policy includes a continuous commitment to improve our
products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. W10665255B
9/30/14
30" (76.2 cm) Freestanding Electric Range
PRODUCT DIMENSIONS
PRODUCT MODEL NUMBERS
WFE715H0E
A
Electrical: To properly install your range, you must determine the type
of electrical connection you will be using and follow the instructions
provided for it here.
• Range must be connected to the proper electrical voltage
and frequency as specified on the model/serial number rating plate.
The model/serial number rating plate is located on the left side frame
behind the storage drawer panel or behnd the top right side
of the oven door. Refer to the figures in the “Product Dimensions”
section of the “Location Requirements” section.
• This range is manufactured with the neutral terminal connected
to the cabinet. Use a 3-wire, UL listed. 40- or 50-amp power supply
cord (pigtail) (see following Range Rating chart). If local codes
do not permit ground through the neutral, use a 4-wire power supply
cord rated at 250 volts, 40 or 50 amps and investigated
for use with ranges.
Range Rating*
Specified Rating of
Power Supply Cord Kit
and Circuit Protection
120/240 Volts
120/208 Volts
Amps
8.8 – 16.5 KW
7.8 – 12.5 KW
40 or 50 **
16.6 – 22.5 KW
12.6 – 18.5 KW
50
* The NEC calculated load is less than the total connected load listed
on the model/serial rating plate.
** If connecting to a 50-amp circuit, use a 50-amp rated cord with a kit.
For 50-amp rated cord kits, use kits that specify use with a nominal
13/8" (34.9 mm) diameter connection opening.
• A circuit breaker is recommended.
CABINET OPENING DIMENSIONS
B
C
F
E
D
A. 273/4" (70.5 cm) max. depth with handle
B. 467/8" (119.1 cm) overall height (max.) with leveling legs
screwed all the way in*
C. 36" (91.4 cm) cooktop height (max.) with leveling legs
screwed all the way in*
D. 297/8" (75.9 cm) width
E. 255/16" (64.3 cm) depth – back of range to front of cooktop**
F. Model/serial rating plate (located on the left side frame behind
storage drawer or right side of frame behind the oven door)
IMPORTANT: Range must be level after installation. Follow
the instructions in the “Level Range” section. Using the cooktop
as a reference for leveling the range is not recommended.
* Range can be raised approximately 1" (2.5 cm)
by adjusting the leveling legs.
** Front of door and drawer may extend further forward
depending on styling.
Cabinet opening dimensions shown are for 25" (64.0 cm)
countertop depth, 24" (61.0 cm) base cabinet depth and 36"
(91.4 cm) countertop height.
IMPORTANT: If installing a range hood or microwave hood
combination above the range, following the range hood or microwave
hoods combination instructions for dimensional clearances
above the cooktop surface.
A freestanding range may be installed next to combustible walls
with zero clearance.
*NOTE: 24" (61.0 cm) minimum when bottom of wood or metal cabinet
is covered by not less than 1/4" (0.64 cm) flame retardant millboard
covered with not less than No. 28 MSG sheet steel, 0.015" (0.4 mm)
stainless steel, 0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper.
Because Whirlpool Corporation includes a continues commitment to improve
our products, we reserve the right to change materials and specifications
without notice.
A
C
B
D
E
F
A. 13" (33.0 cm) max.
upper cabinet depth
B. 30" (76.2 cm) min.
opening width
C. For minimum clearance
to top of cooktop,
see NOTE
D. 301/8" (76.5 cm) min
opening width
E. Outlet – 8" (20.3 cm)
to 22" (55.9 cm) from either
cabinet, 51/2"
(14.0 cm) max. to floor
F. Cabinet door or hinges
should not extend
into the cutout
Dimensions are for planning purposes only. For complete details,
see Installation Instructions packed with product. Specifications
subject to change without notice.
Ref. W10403811C
02/09/15
4/8/2016
Freestanding Electric WFE745H0FH Whirlpool® 6.4 Cu. Ft. Freestanding Electric Range with True Convection from Whirlpool Web World
WHIRLPOOL® 6.4 CU. FT. FREESTANDING ELECTRIC RANGE WITH TRUE CONVECTION
WFE745H0FS
Whirlpool® 6.4 Cu. Ft. Freestanding Electric Range with True Convection
MSRP: $1,049.00
MAJOR APPLIANCE
Email product details | Print Product Details
Specifications
Product Literature
Electrical Requirements
Available Colors
Larger View
AVAILABLE IMAGES
Black Ice Model: WFE745H0FE MAJOR APPLIANCE
White Ice Model: WFE745H0FH MAJOR APPLIANCE
Black­on­Stainless Model: WFE745H0FS MAJOR APPLIANCE
https://secure5.whirlpool.com/catalog/product_popup.jsp?productId=15379&popup=Y&initialSKU=WFE745H0FS
1/4
4/8/2016
Freestanding Electric WFE745H0FH Whirlpool® 6.4 Cu. Ft. Freestanding Electric Range with True Convection from Whirlpool Web World
Related Products
CLOSEOUT
W10306542
ANTI TIP BRACKET ­ Free
Standing Range
W10347384A
Griddle for Whirlpool Aqualift
Range
PT220
4' 3­Wire 40 amp Range Cord
Dimensions
PT400
4' 4­Wire 40 amp Range Cord
PT600
6' 4­Wire 40 amp Range Cord
Key Features
Height
47 7/8
Inches
Depth
27 3/4
Inches
Width
29 7/8
Inches
Gross
Weight
187 LB
Dimensions shown are for planning
purposes only. For complete
information, see Installation Instructions
packed with product.
Frozen Bake™ Technology more
True Convection Cooking more
FlexHeat™ Triple Radiant Element more
Convection Conversion more
AquaLift® Self­Cleaning Technology more
UPC Listing
Model "WFE745H0FE" UPC: 883049396330
Model "WFE745H0FH" UPC: 883049396323
Model "WFE745H0FS" UPC: 883049397603
Specifications
Configuration and Overview
Fuel Type
Electric
Range Type Freestanding
Size
30
Capacity
6.4
Cooktop Features
Cooktop Element Style
Smoothtop
Cooktop Surface Color
Black
Cooktop Surface Material
Porcelain Coated Steel
Number of Cooking Element­
Burners
5
Center Rear Element­Burner
Power
100W
Center Rear Element­Burner
Size
6"
Center Rear Element­Burner
Type
Radiant
Left Front Element­Burner Power
3000W
Left Front Element­Burner Size
12"/9"/6"
Left Front Element­Burner Type
Radiant
Left Rear Element­Burner Power
300W/1300W
Left Rear Element­Burner Size
6"
https://secure5.whirlpool.com/catalog/product_popup.jsp?productId=15379&popup=Y&initialSKU=WFE745H0FS
2/4
4/8/2016
Freestanding Electric WFE745H0FH Whirlpool® 6.4 Cu. Ft. Freestanding Electric Range with True Convection from Whirlpool Web World
Left Rear Element­Burner Type
Radiant Melt
Right Front Element­Burner
Power
3000W
Right Front Element­Burner Size
9"/6"
Right Front Element­Burner Type
Radiant
Right Rear Element­Burner
Power
1200W
Right Rear Element­Burner Size
6"
Right Rear Element­Burner Type
Radiant
Oven Features
Number of Oven Lights
1
Automatic Convection
Conversion Temperature Adjust
Yes
Heating Element On Indicator
Light
Yes
Hot Surface Indicator Light
Yes
Power On Indicator Light
Yes
Bake Element Power
3600W
Broiler Element Power
3600W@240 V
Broiler Location
Top of Oven
Convection Element Power
925
Convection Element Type
True
Convection Functions
Bake; Broil; Roast
Hidden Bake Element
Yes
Light Type
Incandescent
Number of Oven Lights
1
Number of Oven Racks
3
Number of Rack Guides
7
Oven Rack Type
2 Standard and 1 Max Capacity
Controls
Drawer Type
Storage Drawer
Handle Material
Metal
Handle Type
Towel Bar
Selections
Frozen Bake; Energy Save Mode;
Keep Warm Setting; Delay Start;
Cook Time Indicator; Rapid
Preheat; Sabbath Mode; Control
Lock
ADA Compliant
No
UL
Yes
Dimensions
Depth
27 3/4 Inches
Height
47 7/8 Inches
https://secure5.whirlpool.com/catalog/product_popup.jsp?productId=15379&popup=Y&initialSKU=WFE745H0FS
3/4
4/8/2016
Freestanding Electric WFE745H0FH Whirlpool® 6.4 Cu. Ft. Freestanding Electric Range with True Convection from Whirlpool Web World
Width
29 7/8 Inches
General
ADA Compliant
No
https://secure5.whirlpool.com/catalog/product_popup.jsp?productId=15379&popup=Y&initialSKU=WFE745H0FS
4/4
Microwave Hood Combination
PRODUCT MODEL NUMBERS
PRODUCT DIMENSIONS
WMH32L19A
WMH2175XV
GMH3204XV
WMH73L20A
WMH2205XV
GMH5205XV
WMH75520A
WMH3205XV
GMH6185XV
WMH76718A
WMH31017A
WMH1162XV
WMH32517A
WMH1163XV
WMH53520A
WMH1164XW
Electrical: A 120-Volt, 60-Hz, AC-only, 15- or 20-amp fused electrical
supply with a fuse or circuit breaker. A time-delay fuse or time-delay circuit
breaker is recommended. It is recommended that a separate circuit serving
only this microwave oven be provided.
29
15
"
(40
.0 c
m)
VENTING REQUIREMENTS
A 3¹⁄₄" x 10" (8.3 x 25.4 cm) rectangular or 6" (15.2 cm) round vent should be used.
The total length of the vent system including straight vent, elbow(s), transitions and wall
or roof caps must not exceed the equivalent of 140 ft (42.7 m) for either type of vent.
For best performance, use no more than three 90° elbows.
To calculate the length of the system you need, add the equivalent length for each vent
piece used in the system. See the following examples:
A
16 "
(41.3 cm)
17 "
(43.8 cm)
B
" (76.0
cm)
CABINET OPENING DIMENSIONS
The grounded 3-prong outlet must be inside the upper cabinet.
A
B
C
30"
(76.2 cm)
min.
12" (30.5 cm) min.
14" (35.6 cm) max.
upper cabinet and
side cabinet depth
30"
(76.2 cm)
typical*
D
E
F
66" (167.6 cm) min.
G
A. Rectangular to round transition piece: 3 " x 10" to 6" = 5 ft
(8.3 x 25.4 cm to 15.2 cm = 1.5 m)
B. Roof cap: 3 " x 10" = 24 ft (8.3 x 25.4 cm = 7.3 m)
C. 90° elbow: 3 " x 10" = 25 ft (8.3 x 25.4 cm = 7.6 m)
D. 90° elbow: 6" = 10 ft (15.2 cm = 3 m)
E. Wall cap: 3 " x 10" = 40 ft (8.3 x 25.4 cm = 12.2 m)
F. 45° elbow: 6" = 5 ft (15.2 cm = 1.5 m)
G. 90° flat elbow: 3 " x 10" = 10 ft (8.3 x 25.4 cm = 3 m)
6" (15.2 cm) vent system = 73 ft (22.2 m) total
A
B
6 ft (1.8 m)
2 ft
(0.6 m)
A. Two 90° elbows = 20 ft (6.1 m)
B. 1 wall cap = 40 ft (12.2 m)
C. 1 rectangular to round transition
piece = 5 ft (1.5 m)
D. 2 ft (0.6 m) + 6 ft (1.8 m)
straight = 8 ft (2.4 m)
D
C
A. 2" x 4" wall stud
B. Grounded 3-prong outlet
*30" (76.2 cm) is typical for 66" (167.6 cm) installation height.
Exact dimensions may vary depending on type of range/cooktop below.
Rectangular to Round Transition for Roof Venting
NOTE: The minimum 3" (7.6 cm) clearance must exist between
the top of the microwave oven and the rectangular to round
transition piece so that the damper can open freely and fully.
3 " x 10" (8.3 x 25.4 cm) vent system = 73 ft (22.2 m) total
A
B
A
6 ft (1.8 m)
B
C
2 ft
(0.6 m)
D
C
A. One 3 " x 10" (8.3 x 25.4 cm) 90° elbow = 25 ft (7.6 m)
B. 1 wall cap = 40 ft (12.2 m)
C. 2 ft (0.6 m) + 6 ft (1.8 m) straight = 8 ft (2.4 m)
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
E
3" (7.6 cm)
F
A. Roof cap
B. 6" (15.2 cm) min. diameter round vent
C. Elbow (for wall venting only)
D. Wall cap
E. 3 " x 10" to 6" (8.3 x 25.4 cm to 15.2 cm)
rectangular to round transition piece
F. Vent extension piece, at least 3" (7.6 cm) high
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. W10247296B
8/15/12
Microwave Hood Combination
PRODUCT MODEL NUMBERS
PRODUCT DIMENSIONS
WMH53520A
WMH32L19A
WMH73L20A
WMH75520A
WMH76718A
WMH2175XV
WMH2205XV
WMH3205XV
WMH31017A
WMH32517A
WMH32519C
GMH3204XV
GMH5205XV
GMH6185XV
WMH1162XV
WMH1163XV
WMH1164XW
Electrical: A 120-Volt, 60-Hz, AC-only, 15- or 20-amp fused electrical
supply with a fuse or circuit breaker. A time-delay fuse or time-delay circuit
breaker is recommended. It is recommended that a separate circuit serving
only this microwave oven be provided.
15
"
(40
.0 c
m)
VENTING REQUIREMENTS
A 3¹⁄₄" x 10" (8.3 x 25.4 cm) rectangular or 6" (15.2 cm) round vent should be used.
The total length of the vent system including straight vent, elbow(s), transitions and wall
or roof caps must not exceed the equivalent of 140 ft (42.7 m) for either type of vent.
For best performance, use no more than three 90° elbows.
To calculate the length of the system you need, add the equivalent length for each vent
piece used in the system. See the following examples:
A
B
16 "
(41.3 cm)
17 "
(43.8 cm)
CABINET OPENING DIMENSIONS
The grounded 3-prong outlet must be inside the upper cabinet.
A
B
C
30"
(76.2 cm)
min.
12" (30.5 cm) min.
14" (35.6 cm) max.
upper cabinet and
side cabinet depth
30"
(76.2 cm)
typical*
D
E
F
66" (167.6 cm) min.
G
A. Rectangular to round transition piece: 3 " x 10" to 6" = 5 ft
(8.3 x 25.4 cm to 15.2 cm = 1.5 m)
B. Roof cap: 3 " x 10" = 24 ft (8.3 x 25.4 cm = 7.3 m)
C. 90° elbow: 3 " x 10" = 25 ft (8.3 x 25.4 cm = 7.6 m)
D. 90° elbow: 6" = 10 ft (15.2 cm = 3 m)
E. Wall cap: 3 " x 10" = 40 ft (8.3 x 25.4 cm = 12.2 m)
F. 45° elbow: 6" = 5 ft (15.2 cm = 1.5 m)
G. 90° flat elbow: 3 " x 10" = 10 ft (8.3 x 25.4 cm = 3 m)
6" (15.2 cm) vent system = 73 ft (22.2 m) total
A
B
6 ft (1.8 m)
2 ft
(0.6 m)
A. Two 90° elbows = 20 ft (6.1 m)
B. 1 wall cap = 40 ft (12.2 m)
C. 1 rectangular to round transition
piece = 5 ft (1.5 m)
D. 2 ft (0.6 m) + 6 ft (1.8 m)
straight = 8 ft (2.4 m)
D
C
A. 2" x 4" wall stud
B. Grounded 3-prong outlet
*30" (76.2 cm) is typical for 66" (167.6 cm) installation height.
Exact dimensions may vary depending on type of range/cooktop below.
Rectangular to Round Transition for Roof Venting
NOTE: The minimum 3" (7.6 cm) clearance must exist between
the top of the microwave oven and the rectangular to round
transition piece so that the damper can open freely and fully.
3 " x 10" (8.3 x 25.4 cm) vent system = 73 ft (22.2 m) total
A
B
A
6 ft (1.8 m)
B
C
2 ft
(0.6 m)
D
C
A. One 3 " x 10" (8.3 x 25.4 cm) 90° elbow = 25 ft (7.6 m)
B. 1 wall cap = 40 ft (12.2 m)
C. 2 ft (0.6 m) + 6 ft (1.8 m) straight = 8 ft (2.4 m)
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
E
3" (7.6 cm)
F
A. Roof cap
B. 6" (15.2 cm) min. diameter round vent
C. Elbow (for wall venting only)
D. Wall cap
E. 3 " x 10" to 6" (8.3 x 25.4 cm to 15.2 cm)
rectangular to round transition piece
F. Vent extension piece, at least 3" (7.6 cm) high
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. W10247296B
1/16/14
Bottom Mount Refrigerator
PRODUCT MODEL NUMBERS
WRB322DMB
PRODUCT DIMENSIONS
WRB329DMB
Electrical: A 115-volt, 60-Hz, AC-only, 15- or
20-amp fused, grounded electrical supply is
required. It is recommended that a separate
circuit serving only your refrigerator be
provided. Use an outlet that cannot be turned
off by a switch. Do not use an extension
cord.
NOTE: Before performing any type of
installation, cleaning, or removing a light
bulb, turn the control (Thermostat,
Refrigerator or Freezer Control depending on
the model) to OFF and then disconnect the
refrigerator from the electrical source. When
you are finished, reconnect the refrigerator to
the electrical source and reset the control
(Thermostat, Refrigerator or Freezer Control
depending on the model) to the desired
setting. See “Using the Controls.”
Water: A cold water supply with water
pressure between 35 and 120 psi (241 and
827 kPa) is required to operate ice maker
and water dispenser. If you have questions
about your water pressure, call a licensed,
qualified plumber.
IMPORTANT: The pressure of the water
coming out of a reverse osmosis system
going to the water inlet valve of the
refrigerator needs to be between 35 and
120 psi (241 and 827 kPa).
Reverse Osmosis Water Supply: If a
reverse osmosis water filtration system is
connected to your cold water supply, the
water pressure to the reverse osmosis
system needs to be a minimum of 40 to
60 psi (276 to 414 kPa).
H
G
1
cabinet
C
F
not incl.
handle
E
A
incl.
handle
B
top of
cabinet
90˚
overall
4
D
Height Top of
Cabinet
“B”
Depth Doors Open
90°
“C”
681⁄2"
(174 cm)
62"
503⁄4"
333⁄8"
307⁄8"
(157.5 cm) (128.9 cm) (84.8 cm) (78.4 cm)
325⁄8"
281⁄8"
(71.4 cm) (82.9 cm)
67"
65 1⁄2"
59"
50 3⁄4"
33 3⁄8"
30 7⁄8"
WRB329DMB 18.7 cu. ft. (170.2 cm) (166.4 cm) (149.9 cm) (128.9 cm) (84.8 cm) (78.4 cm)
28 1⁄8"
29 5⁄8"
(71.4 cm) (75.2 cm)
Model
Number
Model Size
Height Overall
“A”
70"
WRB322DMB 22.1 cu. ft. (177.8 cm)
Depth Drawer
Open
“D”
Depth With
Handles
“E”
Depth Without
Handles
“F”
Depth Cabinet
Only
“G”
Width Cabinet
“H”
LOCATION REQUIREMENTS
To ensure proper ventilation for your refrigerator, allow for a 1⁄2" (1.25 cm) space on
each side and at the top. Allow at least 1" (2.54 cm) between back of cabinet and the
wall. If your refrigerator has an ice maker, make sure you leave some extra space at
the back for the water line connections.
If you are installing your refrigerator next to a fixed wall, leave 2 1⁄ 2 " (6.3 cm) minimum
on the hinge side (depending on your model) to allow for the door to swing open.
¹⁄₂" (1.25 cm)
NOTE: This refrigerator is intended for use in a location where the temperature ranges
from a minimum of 55°F (13°C) to a maximum of 110°F (43°C). The preferred room
temperature range for optimum performance, which reduces electricity usage and
provides superior cooling, is between 60°F (15°C) and 90°F (32°C). It is
recommended that you do not install the refrigerator near a heat source, such as an
oven or radiator.
2¹⁄₂" (6.3 cm)
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. W10597594B
12/10/14
Top Mount Refrigerator
PRODUCT MODEL NUMBERS
WRT311FZD
WRT511SZD
PRODUCT DIMENSIONS
WRT541SZD
G
Electrical: A 115-volt, 60-Hz, AC-only, 15or 20-amp fused, grounded electrical supply
is required. It is recommended that a
separate circuit serving only your refrigerator
be provided. Use an outlet that cannot be
turned off by a switch. Do not use an
extension cord.
NOTE: Before performing any type of
installation, cleaning, or removing a light
bulb, turn the control (Thermostat,
Refrigerator or Freezer Control depending on
the model) to OFF and then disconnect the
refrigerator from the electrical source. When
you are finished, reconnect the refrigerator to
the electrical source and reset the control
(Thermostat, Refrigerator or Freezer Control
depending on the model) to the desired
setting. See “Using the Controls.”
Water: A cold water supply with water
pressure between 30 and 120 psi (207 and
827 kPa) is required to operate ice maker and
water dispenser. If you have questions about
your water pressure, call a licensed, qualified
plumber.
IMPORTANT: The pressure of the water
coming out of a reverse osmosis system
going to the water inlet valve of the
refrigerator needs to be between 30 and
120 psi (207 and 827 kPa).
Reverse Osmosis Water Supply: If a reverse
osmosis water filtration system is connected
to your cold water supply, the water pressure
to the reverse osmosis system needs to be a
minimum of 40 to 60 psi (276 to 414 kPa).
F
1
cabinet
E
not incl.
handle
D
A
incl.
handle
B
top of
cabinet
C
overall
4
90˚
Model
Number
Model
Size
Reversible
Door
Height Overall
“A”
Height - Depth Depth Top of Door Open
With
Cabinet
90°
Handles
“B”
“C”
“D”
Depth Without
Handles
“E”
Depth Cabinet
Only
“F”
Width Cabinet
“G”
WRT311FZD 20.5 cu. ft.
Yes
66¹⁄₄"
65¹⁄₂"
62¹⁄₄"
32⁷⁄₈"
30⁵⁄₈"
28¹⁄₂"
32³⁄₄"
(168.3 cm) (166.4 cm) (158.1 cm) (83.5 cm) (77.8 cm) (72.4 cm) (83.2 cm)
WRT511SZD
21.3 cu. ft.
WRT541SZD
Yes
34"
66¹⁄₄"
65¹⁄₂"
62¹⁄₄"
32¹⁄₂"
28¹⁄₂"
32³⁄₄"
(168.3 cm) (166.4 cm) (158.1 cm) (86.4 cm) (82.3 cm) (72.4 cm) (83.2 cm)
LOCATION REQUIREMENTS
To ensure proper ventilation for your refrigerator, allow for a 1⁄2" (1.25 cm) space on
each and between overhead cabinets and refrigerator top. Allow at least 1" (2.5 cm)
between back of cabinet and the wall. If your refrigerator has an ice maker, make
sure you leave some extra space at the back for the water line connections.
If you are installing your refrigerator next to a fixed wall, leave 2" (5 cm) minimum
on the hinge side (depending on your model) to allow for the door to swing open.
12
/ " (1.25 cm)
NOTE: This refrigerator is intended for use in a location where the temperature
ranges from a minimum of 55°F (13°C) to a maximum of 110°F (43°C). The
preferred room temperature range for optimum performance, which reduces
electricity usage and provides superior cooling, is between 60°F (15°C) and 90°F
(32°C). It is recommended that you do not install the refrigerator near a heat source,
such as an oven or radiator.
2" (5.08 cm)
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. W10674106
10/29/14
Undercounter Dishwasher
PRODUCT MODEL NUMBERS
WDF110PAB
WDF111PAB
WDF310PAA
WDF310PCA
WDF310PLA
WDF320PAD
WDF510PAY
WDF520PAD
WDF530PAY
WDF530PLY
WDF530PSY
WDF540PAD
PRODUCT DIMENSIONS
WDF730PAY
WDT710PAY
WDT720PAD
WDT770PAY
Electrical Requirements: 120-volt, 60-Hz, AC-only, 15- or
20-amp. fused electrical supply. Copper wire only. A
timedelay fuse or circuit breaker and separate circuit is
recommended.
If direct wiring dishwasher: Use flexible, armored or
nonmetallic, sheathed copper
wire with grounding wire that
meets the wiring requirements for
your home and local codes and ordinances.
Use a U.L.-listed or CSA-approved conduit connector.
If connecting dishwasher with a power supply cord:
Use Power Supply Cord Kit (Part
No. 4317824) marked for use with
dishwashers. Follow the kit
instructions for installing the power supply cord.
Power supply cord must plug into a grounded
three-prong, outlet, located in the cabinet next to
the dishwasher opening. Outlet must meet all local
codes and ordinances.
Water Supply Requirements: A hot water line with 20 to
120 psi (138 to 862 kPa) water pressure. Water
temperature must be 120°F (49°C) water at dishwasher.
Use ³⁄₈" O.D. copper tubing with compression fitting or
flexible braided water supply line (¹⁄₂" minimum plastic
tubing is not recommended). Use a 90° elbow with ³⁄₄"
N.P.T. external pipe threads on one end. Do not solder
within 6" (15.2 cm) from water inlet valve.
Drain Requirements: A new drain hose is supplied with
your dishwasher. If this is not long enough, use a new drain
hose with a maximum length of 12' (3.7 m) (Part No.
3385556) that meets all current AHAM/IAPMO test
standards, is resistant to heat and detergent, and fits the 1"
(2.5 cm) drain connector of the dishwasher.
Make sure to connect the drain hose to waste tee or
disposer inlet above drain trap in house plumbing and 20"
(50.8 cm) minimum above the floor. It is recommended
that the drain hose either be
air gap
looped up and securely
fastened to the underside of
the counter, or be connected
to an air gap.
Make sure to use an air gap
if the drain hose is
connected to house
plumbing lower than 20"
(50.8 cm) above subfloor or
floor.
Use ¹⁄₂" (1.3 cm) minimum I.D. drain line fittings.
If required, the air gap should be installed in accordance
with the air gap installation instructions. When connecting
the air gap a rubber hose (not provided) will be needed to
connect to the waste tee or disposer inlet.
(8533¹⁄₂
m .1
rea in wcm)
r le ith
legvelin
rem
s g
ov
ed
Page 1 of 2
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. W10435040C
9/1/14
CABINET CUTOUT DIMENSIONS
Page 2 of 2
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. W10435040C
9/1/14
Undercounter Dishwasher
PRODUCT MODEL NUMBERS
WDF110PAB
WDF111PAB
WDF310PAA
WDF310PCA
WDF310PLA
WDF320PAD
WDF510PAY
WDF520PAD
WDF530PAY
WDF530PLY
WDF530PSY
WDF540PAD
PRODUCT DIMENSIONS
WDF730PAY
WDT710PAY
WDT720PAD
WDT770PAY
Electrical Requirements: 120-volt, 60-Hz, AC-only, 15- or
20-amp. fused electrical supply. Copper wire only. A
timedelay fuse or circuit breaker and separate circuit is
recommended.
If direct wiring dishwasher: Use flexible, armored or
nonmetallic, sheathed copper
wire with grounding wire that
meets the wiring requirements for
your home and local codes and ordinances.
Use a U.L.-listed or CSA-approved conduit connector.
If connecting dishwasher with a power supply cord:
Use Power Supply Cord Kit (Part
No. 4317824) marked for use with
dishwashers. Follow the kit
instructions for installing the power supply cord.
Power supply cord must plug into a grounded
three-prong, outlet, located in the cabinet next to
the dishwasher opening. Outlet must meet all local
codes and ordinances.
Water Supply Requirements: A hot water line with 20 to
120 psi (138 to 862 kPa) water pressure. Water
temperature must be 120°F (49°C) water at dishwasher.
Use ³⁄₈" O.D. copper tubing with compression fitting or
flexible braided water supply line (¹⁄₂" minimum plastic
tubing is not recommended). Use a 90° elbow with ³⁄₄"
N.P.T. external pipe threads on one end. Do not solder
within 6" (15.2 cm) from water inlet valve.
Drain Requirements: A new drain hose is supplied with
your dishwasher. If this is not long enough, use a new drain
hose with a maximum length of 12' (3.7 m) (Part No.
3385556) that meets all current AHAM/IAPMO test
standards, is resistant to heat and detergent, and fits the 1"
(2.5 cm) drain connector of the dishwasher.
Make sure to connect the drain hose to waste tee or
disposer inlet above drain trap in house plumbing and 20"
(50.8 cm) minimum above the floor. It is recommended
that the drain hose either be
air gap
looped up and securely
fastened to the underside of
the counter, or be connected
to an air gap.
Make sure to use an air gap
if the drain hose is
connected to house
plumbing lower than 20"
(50.8 cm) above subfloor or
floor.
Use ¹⁄₂" (1.3 cm) minimum I.D. drain line fittings.
If required, the air gap should be installed in accordance
with the air gap installation instructions. When connecting
the air gap a rubber hose (not provided) will be needed to
connect to the waste tee or disposer inlet.
(8533¹⁄₂
m .1
rea in wcm)
r le ith
legvelin
rem
s g
ov
ed
Page 1 of 2
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. W10435040C
9/1/14
CABINET CUTOUT DIMENSIONS
Page 2 of 2
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. W10435040C
9/1/14
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising