20V Lithium-Ion Cordless Combi Drill JCB-CD20LI2

20V Lithium-Ion Cordless Combi Drill JCB-CD20LI2
Safety and operating manual
20V Lithium-Ion
Cordless Combi Drill
JCB-CD20LI2
JCB, SO53 3LE
www.JCBDIY.com
Customer Helpline 0333 0143092
ORIGINAL INSTRUCTIONS
GENERAL POWER TOOL SAFETY WARNINGS
a) Keep work area clean and well
lit. Cluttered or dark areas invite
accidents.
b) Do not operate power tools in
explosive atmospheres, such as in
the presence of flammable liquids,
gases or dust. Power tools create
sparks which may ignite the dust
or fumes.
c) Keep children and bystanders
away while operating a power tool.
Distractions can cause you to
lose control.
and matching outlets will reduce
risk of electric shock.
b) Avoid body contact with
earthed or grounded surfaces,
such as pipes, radiators, ranges
and refrigerators. There is an
increased risk of electric shock if
your body is earthed or grounded.
c) Do not expose power tools
to rain or wet conditions. Water
entering a power tool will increase
the risk of electric shock.
d) Do not abuse the cord. Never
use the cord for carrying, pulling
or unplugging the power tool.
Keep cord away from heat, oil,
sharp edges or moving parts.
Damaged or entangled cords
increase the risk of electric shock.
e) When operating a power tool
outdoors, use an extension cord
suitable for outdoor use. Use of
a cord suitable for outdoor use
reduces the risk of electric shock.
f) If operating a power tool in a
damp location is unavoidable, use
a residual current device (RCD)
protected supply. Use of an RCD
reduces the risk of electric shock.
2. Electrical safety
3. Personal safety
WARNING! Read all
safety warnings and all
instructions. Failure to follow the
warnings and instructions may
result in electric shock, fire and/or
serious injury.
Save all warnings and instructions
for future reference.
The term “power tool” in the
warnings refers to your mainsoperated (corded) power tool or
battery-operated (cordless) power
tool.
1. Work area safety
a) Power tool plugs must match
the outlet. Never modify the plug
in any way. Do not use any adapter
plugs with earthed (grounded)
power tools. Unmodified plugs
JCB, SO53 3LE
www.JCBDIY.com
Customer Helpline 0333 0143092
a) Stay alert, watch what you are
doing and use common sense
when operating a power tool. Do
not use a power tool while you
are tired or under the influence
of drugs, alcohol or medication.
A moment of inattention while
operating power tools may result
in serious personal injury.
b) Use personal protective
equipment. Always wear eye
protection. Protective equipment
such as dust mask, non-skid
safety shoes, hard hat, or hearing
protection used for appropriate
conditions will reduce personal
injuries.
c) Prevent unintentional starting.
Ensure the switch is in the offposition before connecting to
power source and/or battery pack,
picking up or carrying the tool.
Carrying power tools with your
finger on the switch or energising
power tools that have the switch
on invites accidents.
d) Remove any adjusting key or
wrench before turning the power
tool on. A wrench or a key left
attached to a rotating part of the
power tool may result in personal
injury.
e) Do not overreach. Keep proper
footing and balance at all times.
This enables better control of
the power tool in unexpected
situations.
f) Dress properly. Do not wear
loose clothing or jewellery. Keep
your hair, clothing and gloves
away from moving parts. Loose
clothes, jewellery or long hair can
be caught in moving parts.
JCB, SO53 3LE
www.JCBDIY.com
Customer Helpline 0333 0143092
g) If devices are provided for the
connection of dust extraction and
collection facilities, ensure these
are connected and properly used.
Use of dust collection can reduce
dust-related hazards.
4. Power tool use and care
a) Do not force the power tool.
Use the correct power tool for
your application. The correct
power tool will do the job better
and safer at the rate for which it
was designed.
b) Do not use the power tool if
the switch does not turn it on and
off. Any power tool that cannot
be controlled with the switch is
dangerous and must be repaired.
c) Disconnect the plug from
the power source and/or the
battery pack from the power tool
before making any adjustments,
changing accessories, or storing
power tools. Such preventive
safety measures reduce the
risk of starting the power tool
accidentally.
d) Store idle power tools out of
the reach of children and do not
allow persons unfamiliar with the
power tool or these instructions
to operate the power tool. Power
tools are dangerous in the hands
of untrained users.
e) Maintain power tools. Check
for misalignment or binding of
moving parts, breakage of parts
and any other condition that may
affect the power tool’s operation.
If damaged, have the power
tool repaired before use. Many
accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and
clean. Properly maintained cutting
tools with sharp cutting edges are
less likely to bind and are easier
to control.
g) Use the power tool, accessories
and tool bits etc. in accordance
with these instructions, taking into
account the working conditions
and the work to be performed. Use
of the power tool for operations
different from those intended
could result in a hazardous
situation.
5. Battery tool use and care
a) Recharge only with the charger
specified by the manufacturer. A
charger that is suitable for one
type of battery pack may create
a risk of fire when used with
another battery pack.
b) Use power tools only with
specifically designated battery
packs. Use of any other battery
packs may create a risk of injury
and fire.
c) When battery pack is not in
use, keep it away from other metal
objects, like paper clips, coins,
keys, nails, screws or other small
metal objects, that can make a
JCB, SO53 3LE
www.JCBDIY.com
Customer Helpline 0333 0143092
connection from one terminal
to another. Shorting the battery
terminals together may cause
burns or a fire.
d) Under abusive conditions,
liquid may be ejected from the
battery; avoid contact. If contact
accidentally occurs, flush with
water. If liquid contacts eyes,
additionally seek medical help.
Liquid ejected from the battery
may cause irritation or burns.
6.Service
a) Have your power tool serviced
by a qualified repair person using
only identical replacement parts.
This will ensure that the safety of
the power tool is maintained.
Drill Safety Warnings
1. Wear ear protectors when
impact drilling. Exposure to noise
can cause hearing loss.
2. Use auxiliary handle(s), if
supplied with the tool. Loss of
control can cause personal injury.
3. Hold power tool by insulated
gripping surfaces, when
performing an operation where
the cutting accessory may contact
hidden wiring. Cutting accessory
contacting a "live" wire may make
exposed metal parts of the power
tool "live" and could give the
operator an electric shock.
SAFETY WARNINGS FOR BATTERY PACK
a) Do not dismantle, open or
shred cells or battery pack.
b) Do not short-circuit a battery
pack. Do not store battery packs
haphazardly in a box or drawer
where they may short-circuit
each other or be short-circuited
by conductive materials. When
battery pack is not in use, keep
it away from other metal objects,
like paper clips, coins, keys,
nails, screws or other small
metal objects, that can make a
connection from one terminal
to another. Shorting the battery
terminals together may cause
burns or a fire.
c) Do not expose battery pack to
heat or fire. Avoid storage in direct
sunlight.
d) Do not subject battery pack to
mechanical shock.
e) In the event of battery leaking,
do not allow the liquid to come
into contact with the skin or eyes.
If contact has been made, wash
the affected area with copious
amounts of water and seek
medical advice.
f) Seek medical advice
immediately if a cell or battery
pack has been swallowed.
g) Keep battery pack clean and
dry.
h) Wipe the battery pack terminals
with a clean dry cloth if they
become dirty.
i) Battery pack needs to be
JCB, SO53 3LE
www.JCBDIY.com
Customer Helpline 0333 0143092
charged before use. Always refer
to this instruction and use the
correct charging procedure.
j) Do not maintain battery pack
on charge when not in use.
k) After extended periods of
storage, it may be necessary to
charge and discharge the battery
pack several times to obtain
maximum performance.
l) Battery pack gives its best
performance when it is operated
at normal room temperature
(20 °C ± 5 °C).
m)When disposing of battery
packs, keep battery packs of
different electrochemical systems
separate from each other.
n) Recharge only with the charger
specified by ROCKWELL. Do not
use any charger other than that
specifically provided for use with
the equipment. A charger that is
suitable for one type of battery
pack may create a risk of fire
when used with another battery
pack.
o) Do not use any battery pack
which is not designed for use with
the equipment.
p) Keep battery pack out of the
reach of children.
q) Retain the original product
literature for future reference.
r) Remove the battery from the
equipment when not in use.
s) Dispose of properly.
SYMBOLS
To reduce the risk of injury, user must read instruction manual
Warning
Wear ear protection
Wear eye protection
Wear dust mask
Do not expose to rain or water
Do not burn
Do not dispose of batteries. Return exhausted batteries to your
local collection or recycling point.
This product has been marked with a symbol relating to removing
electric and electronic waste. This means that this product shall
not be discarded with household waste but that it shall be returned
to a collection system which conforms to the European Directive
2002/96/CE. It will then be recycled or dismantled in order to
reduce the impact on the environment. Electric and electronic
equipment can be hazardous for the environment and for human
health since they contain hazardous substances.
JCB, SO53 3LE
www.JCBDIY.com
Customer Helpline 0333 0143092
COMPONENT LIST
1
2
3
4
8
5
7
1.
2.
3.
4.
5.
6.
7.
8.
6
KEYLESS CHUCK
TORQUE ADJUSTMENT RING
TWO-SPEED GEAR CONTROL
FORWARD/REVERSE ROTATION CONTROL
ON/OFF SWITCH
BATTERY PACK *
BATTERY PACK RELEASE BUTTON
SIGHT LIGHT
* Not all the accessories illustrated or described are included in standard
delivery.
JCB, SO53 3LE
www.JCBDIY.com
Customer Helpline 0333 0143092
TECHNICAL DATA
Voltage
100-240V ~ 50/60Hz
Power
20V
No load speed
0-500/0-1700min
Clutch Positions
22+1+1
Impact rate
0-8000/0-27200 bpm
Max torque(soft/hard)
35/50N.m
Max chuck capacity
13mm
Max. drilling
capacity
Wood
35mm
Steel
13mm
Masonry
16mm
Machine weight
1.6kg
* Voltage measured without workload. Initial battery voltage reaches maximum
of 20 volts. Nominal voltage is 18 volts.
NOISE INFORMATION
A weighted sound pressure LpA: 70dB (A)
A weighted sound power LwA: 81dB (A)
KpA & KwA=3.0dB (A)
Wear ear protection when sound pressure is over: 80dB (A)
VIBRATION INFORMATION
Vibration total values (triax vector sum) determined according to EN 60745:
Impact drilling into concrete
Drilling into metal
Vibration emission value ah=9.44m/s²
Uncertainty K=1.5m/s²
Vibration emission value ah=3.77m/s²
Uncertainty K=1.5m/s²
The declared vibration total value may be used for comparing one tool with another,
and may also be used in a preliminary assessment of exposure.
JCB, SO53 3LE
www.JCBDIY.com
Customer Helpline 0333 0143092
WARNING:The vibration emission value during actual use of the power tool can differ
from the declared value depending on the ways in which the tool is used dependant on
the following examples and other variations on how the tool is used:
How the tool is used and the materials being cut or drilled.
The tool being in good condition and well maintained
The use the correct accessory for the tool and ensuring it is sharp and in good
condition.
The tightness of the grip on the handles and if any anti vibration accessories are
used.
And the tool is being used as intended by its design and these instructions.
This tool may cause hand-arm vibration syndrome if its use is not adequately
managed.
WARNING: To be accurate, an estimation of exposure level in the actual conditions
of use should also take account of all parts of the operating cycle such as the times
when the tool is switched off and when it is running idle but not actually doing the job. This
may significantly reduce the exposure level over the total working period.
Helping to minimize your vibration exposure risk.
ALWAYS use sharp chisels, drills and blades.
Maintain this tool in accordance with these instructions and keep well lubricated (where
appropriate).
If the tool is to be used regularly then invest in anti vibration accessories.
Avoid using tools in temperatures of 10oC or less.
Plan your work schedule to spread any high vibration tool use across a number of days.
ACCESSORIES
1.5Ah Lithium battery pack
3-5hr Charger
Double ended bit
We recommend that you purchase your accessories from the same store that
sold you the tool. Use good quality accessories marked with a well-known brand
name. Choose the type according to the work you intend to undertake. Refer to the
accessory packaging for further details. Store personnel can assist you and offer
advice.
JCB, SO53 3LE
www.JCBDIY.com
Customer Helpline 0333 0143092
2
1
1
OPERATING INSTRUCTIONS
NOTE: Before using the tool,
read the instruction book
carefully.
INTENDED USE
A
7
The machine is intended for driving in
and loosening screws as well as for
drilling in wood, metal and plastic.
BEFORE PUTTING INTO
OPERATION
A) CHARGING THE BATTERY
The battery charger supplied
is matched to the Li-ion battery
installed in the machine. Do not use
another battery charger.
The Li-ion battery is protected
against deep discharging. When
the battery is empty, the machine
is switched off by means of a
protective circuit: The tool holder no
longer rotates.
In a warm environment or after
heavy use, the battery pack may
become too hot to permit charging.
Allow time for the battery to cool
down before recharging.
When the battery pack is charged
for the first time and after prolonged
storage, the battery pack will accept
a 100% charge after several charge
and discharge cycles.
B) TO REMOVE OR INSTALL
BATTERY PACK (See A)
Depress the battery pack release
button (7) to release and slide the
battery pack out from your tool. After
JCB, SO53 3LE
www.JCBDIY.com
Customer Helpline 0333 0143092
B
5
C1
4
C2
4
B
B
recharge, slide it back into your tool.
A simple push with slight pressure will
be sufficient.
5
OPERATION
1. ON / OFF SWITCH (See B)
5
Depress the On/Off switch (5) to
start and release it to stop your
drill. The on/off switch is fitted with
a brake function which stops your
chuck immediately when you quickly
release the switch.
It is also a variable speed switch
that delivers higher speed and
torque with increased trigger
pressure. Speed is controlled by the
amount of switch trigger pression.
Warning: Do not operate for
long periods at low speed
because excess heat will be
produced internally.
C1
C1
4
4
C2
2. SWITCH LOCK
The switch trigger can be locked in
the OFF position. This helps to reduce
the possibility of accidental starting
when not in use. To lock the switch
trigger, place the rotation control in
the center position.
C2
4
4
3. REVERSIBLE (See C1, C2)
D
D
3
3
JCB, SO53 3LE
www.JCBDIY.com
Customer
Helpline 0333 0143092
E
For drilling and screw driving use
forward rotation (4) marked “
”
(lever is moved to the left). Only use
reverse rotation marked “
” (lever
is moved to the right) to remove screws
or release a jammed drill bit.
Warning: Never change the
direction of rotation when the
chuck is rotating, wait until it has
stopped!
D
3
4. TWO-SPEED GEAR
CONTROL (See D)
The drill has a two-speed gear
control designed for drilling or
driving at LOW (mark is 1) or HIGH
(mark is 2) speeds. A slide switch is
located on top of the drill to select
either LOW or HIGH speed. When
using the drill in the LOW speed
range, the speed will decrease and
the drill will have greater power and
torque. When using the drill in the
HIGH speed range, the speed will
increase and the drill will have less
power and torque.
E
Gear I
Low speed range: for screw
driving or working with large drilling
diameter
Gear II
High speed range: for working with
small drilling diameter
Warning:To prevent gear
damage, always allow the
chuck to come to a complete stop
before changing the direction of
rotation or the two-speed gear
control.
F
G
JCB, SO53 3LE
www.JCBDIY.com
Customer Helpline 0333 0143092
E
5. CHUCK ADJUSTMENT
(See E)
To open the chuck jaws rotate the
front section of the chuck. Insert
the drill bit between the chuck jaws
and rotate the front section in the
opposite direction. Ensure the drill
bit is in the center of the chuck jaws.
Finally, firmly rotate the front chuck
section in the opposite directions.
Your drill bit is now clamped in the
chuck..
F
6. TORQUE ADJUSTMENT
(See F)
(Screw driving force of your drill
driver)
The torque is adjusted by rotating
the torque adjustment ring. The
torque is greater when the torque
adjustment ring is set on a higher
setting. The torque is less when the
torque adjustment ring is set on a
lower setting.
Make the setting as follows:
1 - 4 For driving small screws
5 - 9 For driving screws into soft
material
10 - 14 For driving screws into soft
and hard material
15 - 19 For driving screws into hard
wood
20 - 22 For driving larger screws
For heavy drilling
For drilling in masonry and
concrete
F
G
G
H
H
JCB, SO53 3LE
www.JCBDIY.com
Customer Helpline 0333 0143092
9
7. AUTOMATIC SPINDLE
LOCK (See G)
The automatic spindle lock
allows you to use it as a regular
screwdriver. You can give an extra
twist to firmly tighten a screw,
loosen a very tight screw or
continue working when the battery
energy has expired. For manual
screwdriver purposes, the chuck is
automatically locked when the tool
is off.
G
H
8. USING THE LED LIGHT
(See H)
The LED light allows you to keep
a clear view under less illuminated
circumstances. To turn on the light
simply press the on/off switch.
When you release the on/off switch,
the light will go out.
9. DRILLING
When drilling into a hard smooth
surface, use a center punch to mark
the desired hole location. This will
prevent the drill bit from slipping off
center as the hole is started. Hold
the tool firmly and place the tip of the
bit at the point to be drilled. Depress
the switch trigger to start the tool.
Move the drill bit into the workpiece,
applying only enough pressure to
keep the bit rotating. Do not force
or apply side pressure to elongate a
hole.
Tungsten carbide drill bits
JCB, SO53 3LE
www.JCBDIY.com
Customer Helpline 0333 0143092
9
should always be used for
concrete and masonry. When
drilling in metal, only use HSS drill
bits in good condition. Always use
a magnetic bit holder (not
included) when using short
screwdriver bits. When screwdriving, apply a small quantity of
liquid soap or similar to the screw
threads to ease insertion.
10. DISPOSAL OF AN
EXHAUSTED BATTERY
PACK
To preserve natural
resources, please recycle
or dispose of the battery
pack properly. This battery pack
contains Lithium batteries. Consult
your local waste authority for
information regarding available
recycling and/or disposal options.
Discharge your battery pack by
operating your drill, then remove
the battery pack from the drill
housing and cover the battery
pack connections with heavy-duty
adhesive tape to prevent short
circuit and energy discharge. Do
not attempt to open or remove any
of the components.
11. OVERLOAD
PROTECTION
When overloaded, the motor comes to
a stop.Release the on/off button, and
the machine will restart immediately.
JCB, SO53 3LE
www.JCBDIY.com
Customer Helpline 0333 0143092
12. TEMPERATURE
DEPENDENT OVERLOAD
PROTECTION
When using as intended the power
tool cannot be subject to overload.
When the load is too high or the
allowable battery temperature of 75°C
is exceeded, the electronic control
switches off the power tool until
the temperature is in the optimum
temperature range again.
13. PROTECTION AGAINST
DEEP DISCHARGING
The Li-ion battery is protected against
deep discharging by the “Discharging
Protection System”. When the battery
is empty, the machine is switched off
by means of a protective circuit: When
this occurs your tool will not switch
on. Remove and recharge the battery
pack.
PROBLEM SOLUTION
1. WHY DOES THE DRILL NOT TURN ON WHEN YOU PRESS THE
SWITCH?
The forward/reverse rotation control, which is on top of the trigger, is positioned in the
lock function. Unlock the forward/reverse rotation control by putting it into the required
rotation position. Push the trigger and the drill will start to rotate.
Or if the LED light flashes at the same time you press the Switch, please charge the
battery.
2. THE DRILL STOPS BEFORE THE SCREW IS COMPLETELY
TIGHTENED. WHY?
Verify the torque position of the torque adjusting ring, you can find the torque-adjusting
ring between the chuck and the drill body. Position 1 is the lowest torque (screw driving
force) and position 20 is the highest torque (screw driving force). Position 21 is for drill
operation. Regulate the torque adjusting ring to a higher position to reach the best
result.
3. REASONS FOR DIFFERENT BATTERY PACK WORKING TIMES
Charging time problems, as above, and having not used a battery pack for a
prolonged time will reduce the battery pack working time. This can be corrected after
several charge and discharge operations by charging & working with your drill. Heavy
working conditions such as large screws into hard wood will use up the battery pack
energy faster than lighter working conditions. Do not re-charge your battery pack
below 0°C and above 45°C as this will affect performance.
JCB, SO53 3LE
www.JCBDIY.com
Customer Helpline 0333 0143092
MAINTENANCE
Your tool requires no additional lubrication or maintenance.
There are no user serviceable parts in your power tool. Never use water or chemical
cleaners to clean your power tool. Wipe clean with a dry cloth. Always store your power
tool in a dry place. Keep the motor ventilation slots clean. Keep all working controls
free of dust. Occasionally you may see sparks through the ventilation slots. This is
normal and will not damage your power tool.
ENVIRONMENTAL PROTECTION
This product has been marked with a symbol relating to removing electric
and electronic waste. This means that this product shall not be discarded
with household waste but that it shall be returned to a collection system
which conforms to the European Directive 2002/96/CE. It will then be recycled or
dismantled in order to reduce the impact on the environment. Electric and
electronic equipment can be hazardous for the environment and for human health
since they contain hazardous substances.
JCB, SO53 3LE
www.JCBDIY.com
Customer Helpline 0333 0143092
WARRANTY STATEMENT
A product of hard work
In every corner of the world you'll find a JCB machine. Since our beginnings in
1945, we have always invested heavily in research and development, keeping JCB
at the cutting edge of innovation. Today, JCB has some of the finest engineering
facilities across the globe, producing a range of over 300 machines and maintains
a reputation for unrivaled customer service. The same innovation to always get
the job done better, the same quality to never let you down, the same engineering
heritage and expertise that you can trust, can be found in JCB Power Tools.
JCB power tools are guaranteed against manufacturing defects for a period of 3
years from the date of purchase.
If your JCB power tool becomes defective within this warranty period, we
guarantee to:
• Replace or repair all defective parts, free of charge, or
• Repair products free of charge, or
• Replace the unit with a new or re-conditioned unit, free of charge.
Conditions
Your 3 year guarantee does not cover defects caused by or resulting from:
• overload, misuse, or neglect
• normal wear and tear, including accessory wear
• hire use
• repairs attempted by anyone other than an authorised agent
• damage caused by foreign objects, substances or accidents
Your 3 year guarantee does not cover:
• battery packs as they are guaranteed for a 12 month period
• accessories supplied with the power tool.
Warranty claims
For guarantee claims, please contact JCB Customer Services. You will be required
to submit proof of purchase.
JCB CUSTOMER HELPLINE 0333 0143092
Terms
This guarantee does not affect your statutory rights. JCB SO53 3LE (Registered in
England under No. 973387).
JCB, SO53 3LE
www.JCBDIY.com
Customer Helpline 0333 0143092
EC DECLARATION OF CONFORMITY
We,
Positec Power Tools (Europe) Ltd, PO Box 152,
Leeds, LS10 9DS, UK
Declare that the product
Description
20V Lithium-Ion Cordless Combi Drill
Type
JCB-CD20LI2
Function
Drilling
Complies with the following Directives,
EC Machinery Directive
2006/42/EC
EC Electromagnetic Compatibility Directive
2004/108/EC
RoHS Directive
2011/65/EU
Standards conform to
EN 55014-1
EN 55014-2
EN 60745-1
EN 60745-2-1
EN 60745-2-2
The person authorized to compile the technical file,
Name: Russell Nicholson
Address: Positec Power Tools (Europe)Ltd,
PO Box 152,Leeds,LS10 9DS,UK
2014/11/25
Allen Ding
Deputy Chief Engineer,Testing & Certification
JCB, SO53 3LE
www.JCBDIY.com
Customer Helpline 0333 0143092
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising