Atlona AT-HD4-V40SRS User manual

Atlona AT-HD4-V40SRS User manual

Atlona HDMI with Bi-Direction IR

Extender over Single CAT5, 6, and 7 up to 130 Feet

AT-HD4-V40SRS

Toll free: 1-877-536-3976

Local: 1-408-962-0515

User Manual

atlona.com

Table of Contents

1. Introduction

2. Package Contents

3. Features

5. Panel Descriptions

5.1. Transmitting Module

5.1.1. Front Panel

5.1.2. Rear Panel

5.2. Receiving Module

5.2.1. Front Panel

5.2.2. Rear Panel

6. IR Pass-through

6.1. IR Extenders

6.2. IR Sockets

6.4. Supported IR Data Format

7. Installation

8. EDID Learning

9.1. HDMI

TM

9.2. CAT5 [RJ45]

10. Connection Diagram

11. Performance Guide

12. Notice

13. Safety Information

14. Warranty

15. Atlona Product Registration

.................................................. 3

.................................................. 3

.................................................. 3

.................................................. 4

.................................................. 5

.................................................. 5

.................................................. 5

.................................................. 5

.................................................. 6

.................................................. 6

.................................................. 6

.................................................. 7

.................................................. 7

.................................................. 7

.................................................. 7

.................................................. 8

.................................................. 8

.................................................. 8

.................................................. 9

.................................................. 9

.................................................. 9

.................................................. 10

.................................................. 10

.................................................. 11

.................................................. 12

.................................................. 13

.................................................. 14

Toll free: 1-877-536-3976

Local: 1-408-962-0515 atlona.com

INTRODUCTION

The Atlona AT-HD4-V40SRS is an HDMI with Bi-Directional IR Extension Kit. The extenders are designed to handle full 1080p up to 130ft and 1080i/720p up to 200ft. The HD4-V40SRS are capable of supporting very high bandwidth and there are able to handle all 7 x 3D formats.

The Atlona HD4-V40SRS are based on the latest HDMI technology and therefore are capable of fully supporting

HDCP 2.0, Deep Color and DTS-HD or Dolby TrueHD audio. In addition, AT-HD4-V40SRS are also equipped with bi-directional IR pass-through, which allows users to control the sources from the remote location as well as sending IR signal from a control system to a remote location. Perfect for Control4, RTI, HAI or any other control system users or dealers.

The AT-HD4-V40SRS includes two modules: transmitting module and receiving module, where the transmitter module converts HDMI with IR to RJ45 and the receiver module converts it back to HDMI and IR. The receiver module is featured with 8-step equalization control, to allow users to adjust the equalization strength to the received HDMI signals accordingly, and therefore optimize the transmission distance between source and display.

PACKAGE CONTENTS

• 1x AT-HD4-V40SRS (Transmitting and Receiving Modules)

• 1x IR blaster

• 1x IR receiver

• 2x 5V power supply unit

• 1x Use r’s manual

FEATURES

• Extends the transmission range up to 130ft (40m) at full 1080p or 1920x1200 or 200ft (60M) at 1080i/720p

• Supports all latest Audio formats such as Dolby True HD, DTS-master, etc…

• 3D Compatible (all 7 formats), including the most popular e.g., Frame Packing, Side-by-Side, Top-to-Bottom,

etc...

• 7 x Embedded EDID functions and Learning EDID function available. Learning function allows user to trick

the source to think that it connected to the display rather than going though extenders.

a lot of EDID issues which may happened in a complicated installations with different components involved.

• Supports Bi-Directional IR pass-through up to 60Khz, allows users not only send IR signals from remote

location but also to remote location from a control system. Great for Control4 or RTI installers.

• Supports VES A DDC and Hot-Plug Detect (HPD)

• HDC P compatible

• DVI 1.0 compliant, user will need to use DVI/HDMI adapter

• Supports Deep Color

• Allows cascading

• Wall mounting housing design for easy and robust installation

• Locking Power connector

* The claimed transmission distance is subject to the grade of installed cable(s), source devices and displays.

* For Cat.X transmission, the cable(s) should be solid, not stranded. Any keystone jack along the transmission

Toll free: 1-877-536-3976

Local: 1-408-962-0515

3 atlona.com

SPECIFICATIONS

Technical

Role of usage

HDCP compliance

Video bandwidth

Video support

HDMI over UTP transmission

Audio support

Signal Equalization

Input TMDS signal

Input DDC signal

ESD protection

PCB stack-up

IR pass-thru

Input

Output

HDMI

TM

source control

IR remote control

HDMI

TM

connector

RJ45 connector

3.5mm connector

Rotary control switch

Mechanical

Housing

Dimensions

[L x W x H]

Model

Package

Weight

Carton

Model

Package

Fixedness

Power supply

Power consumption

Operation temperature

Storage temperature

Relative humidity

Transmitter

Transmitter [TX]

Yes

Single-link 6.75Gbps [225MHz]

Receiver

Receiver [RX]

480i/p / 720p (50/60) / 1080i (50/60) / 1080p (30/50/60)

Full HD (1080p)-130ft (40m) [CAT5e] / 165ft (50m) [CAT6] HD (720p/1080i)-

165ft (50m) [CAT5e] / 200ft (60m) [CAT6]

Surround sound (up to 7.1ch) or stereo digital audio

8-level digital control at RX

1.2 Volts [peak-to-peak]

5 Volts [peak-to-peak, TTL]

[1] Human body model — ±19kV [air-gap discharge] & ±12kV [contact discharge]

[2] Core chipset — ±8kV

4-layer board [impedance control — dif ferential 100Ω; single 50Ω]

Bi-directional

1x HDMI; 1x 3.5mm

1x RJ45; 1x 3.5mm

1x RJ45; 1x 3.5mm

1x HDMITM; 1x 3.5mm

Controllable via IR pass-through from RX to TX with IR extenders

Electro-optical characteristics: τ = 25° / Carrier frequency: 20-60kHz

Type A [19-pin female]

WE/SS 8P8C with 2 LED indicators

IR receiver

EDID Mode

IR blaster

Signal level

Metal enclosure

2.9” x 3.5” x 1” (75 x 90 x 25mm)

6.9” x 10.6” x 3.1” (175 x 270 x 80mm)

1’3” x 1’6” x 1’ (370 x 450 x 300mm)

1.1 lbs (480g)

1.7 lbs (780g)

Wall-mounting case with screws

5V 2A DC

1.5 W

32~104°F (0~40°C)

-4~140°F (-20~60°C)

20~90% RH (no condensation)

Toll free: 1-877-536-3976

Local: 1-408-962-0515

4 atlona.com

PANEL DESCRIPTIONS

5.1. Transmitting Module

5.1.1. Front Panel

1 2 3 4

1. MODE:

0 - EDID Full-HD (up to [email protected]) -24bit 2D video & 7.1ch audio – long distance

1 - EDID Full-HD (up to [email protected]) – 24-bit 2D video & 2ch audio – long distamce

2 - EDID Full-HD ([email protected]) - 36bit 2D video & 7.1ch audio

3 - EDID Full-HD ([email protected]) - 36bit 2D video & 2ch audio

4 - EDID Full-HD ([email protected]) - 36bit 3D video & 7.1ch audio

5 - EDID HD ([email protected])([email protected]/60)([email protected]/60) - 24bit 2D video & 2ch audio

6 - EDID Full-HD ([email protected]) - 36bit 3D video & 2ch audio

7 - EDID learning mode

2. HDMI IN:

Connects to a HDMI source with a HDMI male-male cable

3. IR Receiver:

Infrared 3.5mm socket for plugging in the extension cable of IR receiver

4. IR Blaster:

Infrared 3.5mm socket for plugging in the extension cable of IR blaster

5.1.2. Rear Panel

1 2

1. +5V DC: Connect to 5V DC power supply.

2. CAT5/6/7 OUT: Plug in a Cat-5/5e/6/7 cable that needs to be linked to the Transmitting module.

Toll free: 1-877-536-3976

Local: 1-408-962-0515

5 atlona.com

5.2. Receiving Module

5.2.1. Front Panel

1 2 3 4

1. EQ:

Adjust the 8-level equalization control to the received HDMI

TM

signals. The HDMI

TM signal level

varies from MAX (strongest) to MIN (weakest) for respective transmission length from longest possible range

to short distance. Please adjust the signal level from MIN to MAX and stop turning the rotary switch when-

ever the audio/video is playing normally.

2. HDMI OUT:

Connect to HDMI display with a HDMI male-male cable.

3. IR Receiver:

Infrared 3.5mm socket for plugging in the extension cable of IR receiver

4. IR Blaster:

Infrared 3.5mm socket for plugging in the extension cable of IR blaster

5.2.2. Rear Panel

1 2

1. +5V DC:

Connect to 5V DC power supply.

2. CAT5/6/7 IN:

Plug in a Cat-5/5e/6/7 cable that needs to be linked to the Receiving module.

Toll free: 1-877-536-3976

Local: 1-408-962-0515

6 atlona.com

IR PASS-THROUGH

6.1. IR Extenders.

IR Blaster IR Receiver

6.2. IR Sockets.

IR BLASTER: plug in the IR blaster to emit all IR command signals received from the IR receiver from the other end to control the devices corresponding to the IR signals.

IR RECEIVER: plug in the IR receiver to receive all IR command signals from the IR remote controls of the corresponding devices.

Note: IR Blaster is designed to be attached to the Source device

Note: IR Receiver is designed to be placed somewhere in the remote location where an IR Remote could be pointed to it.

CAUTION!

Incorrect placement of IR Blaster and Receiver may result in the failure of the IR extenders. Please check carefully before plugging in the IR extender to the respective IR sockets. Warranty will not cover the damage.

IR Blaster

1 2

1. IR Signal (20-60KHz)

2. Grounding

IR Receiver

1 2 3

1. IR Signal (20-60KHz)

2. Grounding

3. Power

However, IR cables longer than 2m (6-ft) may not work.

Toll free: 1-877-536-3976

Local: 1-408-962-0515

7 atlona.com

6.4. Supported IR Data Format.

Data Format

NEC

RC5

TOSHIBA MICOM CODE

GRUNDIG CODE

SONY 12 BIT CODE

SONY 15 BIT CODE

SONY 20 BIT CODE

RCA CODE

RCM CODE

MATSUSHITA CODE

MITSUBISHI CODE

ZENITH CODE

JVC CODE

M50560-001P

MN6125H

MN6125L

MN6014_C5D7

MN6014_C6D6

MC14457P

LC7464(AHEA)

GEMINI_CM

Suitable

v v v v v v v v v v v v v v v v v v

Not Recommended

v v v

INSTALLATION

1. Connect a HDMI or DVI source (such as a Blu-ray Disc player) to the transmitting module of AT-HD4- V40SRS.

2. Connect a HDMITM or DVI display (such as a LCD TV) to the receiving module of AT-HD4-V40SRS.

3. Connect IR Blaster/Receiver to both TX and RX modules.

4. Connect a Cat-5/5e/6/7 cable between the transmitting and receiving modules.

5. Make sure this Cat-5/5e/6/7 cable is tightly connected and not loose.

6. Plug in 5V DC power supply unit to the power jack of the receiving module of AT-HD4-V40SRS.

7. Plug in 5V DC power supply unit to the power jack of the transmitting module of AT-HD4-V40SRS.

cable skew. MAX stands for the strongest HDMITM signal level for longest possible transmission length while

MIN stands for the weakest HDMITM signal level for short transmission length. Please adjust the signal level

from MIN to MAX and stop turning the rotary switch whenever the audio/video is playing normally.

EDID LEARNING

1. Turn off TX module and disconnect the Cat.5/5e/6/7 cable between TX and RX modules.

2. Connect the HDMI display to

“HDMI IN”

on the TX module with a HDMITM cable.

3. Set

“MODE”

on the transmitting module of AT-HD4-V40SRS at 7.

4. Connect the TX module to the power supply.

5. The LED on the RJ45 of the transmitting module will dim and light again, which indicates the EDID learning

procedure is complete.

Toll free: 1-877-536-3976

Local: 1-408-962-0515

8 atlona.com

PIN DEFINITION

9.1. HDMI

TM

Pin 1

Pin 2

Pin 3

Pin 4

Pin 5

Pin 6

Pin 7

Type A (Receptacle) HDMI

TM

TMDS Data2+

TMDS Data2 Shield

TMDS Data2-

TMDS Data1+

TMDS Data1 Shield

TMDS Data1-

TMDS Data0+

Pin 8

Pin 9

TMDS Data0 Shield

TMDS Data0-

Pin 10 TMDS Clock+

Pin 11 TMDS Clock Shield

Pin 12 TMDS Clock-

Pin 13 CEC

Pin 14 Reserved (N.C. on device)

Pin 15 SCL

Pin 16 SDA

Pin 17 DDC/CEC Ground

Pin 18 +5 V Power

Pin 19 Hot Plug Detect

6

7

4

5

8

PIN

1

2

3

9.2. CAT5 [RJ45]

Data Link TIA/EIA-568-B

Color Function

W-O

O

TX0-

TX0+

G-O

BL

W-BL

G

W-BR

BR

TX1-

TX2-

TX2+

TX1+

TXC-

TXC+

RJ-45 Jack

Toll free: 1-877-536-3976

Local: 1-408-962-0515

9 atlona.com

CONNECTION DIAGRAM

DVD Player

AT-HD4-V40SRS

Transmitter

AT-HD4-V40SRS

Receiver

CAT5/6 cable

HDTV

PERFORMANCE GUIDE

Performance rating

Wiring

Shielding

Solid

Unshielded (UTP)

Shielded (STP)

Stranded

Unshielded (UTP)

Shielded (STP)

Termination

CAT5

Type of category cable

CAT5e CAT6

*

*

***

***

****

***

**

*

*****

****

**

**

Please use

EIA/TIA-568-B

termination (

T568B

) at any time

Toll free: 1-877-536-3976

Local: 1-408-962-0515

10 atlona.com

NOTICE

1. When adjusting the signal level on the receiver module, please dial the rotary control switch from MIN to MAX

and stop turning the rotary switch whenever the audio/video is playing normally. Inappropriate signal level

2. Wrongly insert IR blaster and IR receiver to wrong 3.5mm infrared sockets may result in the failure of the IR

extenders. Please check carefully before plugging in the IR extender to the respective IR sockets.

3. If the DVI or HDMI

TM d e v i c e r e q u ri e s t h e E D I D

provide DVI or HDMI

TM

display EDID information.

i n f o r m a it o n , p l e a s e u s e E D I D R e a d e /r W r ti e r t o r e t ir e v e a n d

4. All HDMI

TM

over CAT5 transmission distances are measured using Belden 1583A CAT5e 125MHz UTP

cable and ASTRODESIGN Video Signal Generator VG-859C & VG-870B.

5. The transmission length is largely affected by the type of Cat-5/5e/6 cables, the type of HDMI

the type of HDMI

TM

TM

sources, and

display. The testing result shows solid UTP cables (usually in the form of 300m [1,000ft]

patch cords). Shielded STP cables are better suited than unshielded UTP cables. A solid UTP Cat-5e cable

shows longer transmission range than stranded STP Cat-6 cable. For long extension applications, solid UTP/

STP cables are the only viable choice.

6. EIA/TIA-568-B termination (T568B) for Cat-5/5e/6 cables is recommended for better performance.

7. To reduce the interference among the unshielded twisted pairs of wires in Cat-5/5e/6 cable, one can use

shielded STP cables to improve EMI problems, which is worsen in long transmission.

8. Because the quality of the CAT5/6 cables has the major effect on how long the transmission limit can achieve

and how good is the received picture quality, the actual transmission range is subject to one’s choice of

Cat-5/5e/6 cables. For desired resolutions greater than 1080i or 1280x1024, a Cat-6 cable is recommended.

9. If your HDMI

TM

display has multiple HDMI

TM TM

input [HDMI

TM

input #1]

generally can produce better transmission performance among all HDMI

TM

inputs.

Possible Issues and Solutions:

1. No Audio/video Signal on the Display or Signal is going in and Out:

a. Please test your RJ45 cables with a Fluke or similar tester to make sure that all the wires are connected

and the distance is within the limits.

b. If you are using patch panel or and RJ45 wall plates, the distance will be reduced, please do a direct con-

necting bypassing all additional equipment.

c. Please try to re-terminate your CAT5/6/7 wire to 568B

d. Please try adjusting EQ gain on the receiver unit

e. Please try changing a mode on the transmitter to #0 or to #1 (depending on the audio format required

f. Please go into the menu of the source device and select 720p/1080i or 1080p resolution instead of AUTO

g. If the sync device is a projector or AVR, please try learning EDID, instructions are on the previous page

2. When connected between 3D player and 3D display, only able to see 2D image:

a. Please try changing “MODE” on the transmitter module to 4 or 6

b. Please go into the menu of the source device and enable 3D

3. Signal is Going In and Out when going into the AVR; however works well connected directly to the TV

a. Please try Learning EDID of the AVR while the AVR HDMI out is connected to the display (both AVR and

Display should be ON)

b. Select “MODE” on the transmitter to # 0, #2 or # 4

Toll free: 1-877-536-3976

Local: 1-408-962-0515 11 atlona.com

Safety Information

Safeguards

To reduce the risk of electric shock, do not expose this product to rain or moisture local power socket, hire an electrician to replace your obsolete socket.

Precautions

Do not modify the wall plug. Doing so will void the warranty and safety features.

This equipment should be installed near the socket outlet and the device should be easily accessible in the case it requires disconnection.

expressly approved by the manufacturer, could void the user’s authority to operate this equipment.

Operate this product using only the included external power supply. Use of other power supplies

In the event of an electrostatic discharge this device may automatically turn off. If this occurs, unplug the device and plug it back in.

Protect and route power cords so they will not be stepped on or pinched by anything placed on or against them. Be especially careful of plug-ins or cord exit points from this product.

Avoid excessive humidity, sudden temperature changes or temperature extremes.

tanks, and swimming pools.

Never open, remove unit panels, or make any adjustments not described in this manual.

Attempting to do so could expose you to dangerous electrical shock or other hazards. It may also cause damage to your AT-HD4-V40SRS. Opening the product will void the warranty.

Do not attempt to service the unit. Disconnect the product and contact your authorized Atlona reseller or contact Atlona directly.

Toll free: 1-877-536-3976

Local: 1-408-962-0515

12 atlona.com

Warranty

Limited Warranty

Atlona Technologies warrants that (a) its products (the AT-HD4-V40SRS) will perform substantially in accordance with the accompanying written materials for a period of 3 years from the date of receipt and (b) that the product will be free from defects in materials and workmanship under normal use and service for a period of 3 years. In the event applicable law imposes any implied warranties, the implied warranty period is limited to 3 years from the date of receipt. Some jurisdictions do not allow such limitations on duration of an implied warranty, so the above limitation may not apply to customers that fall within those areas.

Customer Remedies

Atlona Technologies’ and its suppliers’ entire liability and Customer’s exclusive remedy shall be, at Atlona Technologies’ decision, either return of the price paid for the product, repair, or replacement of the product that does not meet this Limited Warranty and which is returned to

Atlona Technologies with a copy of the Customer’s receipt. This Limited Warranty is void if failure of the product has resulted from accident, abuse, misapplication, or natural occurrence. In example but not limited to: power surges (electrical storms, local power outage), dropping the product (or

Any replacement product will be warranted for the remainder of the original warranty period.

No other warranties

To the maximum extent permitted by applicable law, Atlona Technologies and its suppliers disclaim all other warranties, either expressed or implied, including, but not limited to, implied

Customers may have other rights depending on the jurisdiction.

No liability for damages

To the maximum extent permitted by applicable law, in no event shall Atlona Technologies or its suppliers be liable for any damages arising out of the use of or inability to use this product, even if Atlona Technologies has been advised of the possibility of such damages. Such damages include but are not limited to: special, incidental, consequential, or indirect damages for personal injury, loss. Atlona Technologies’ and its suppliers’ entire liability under any provision of this agreement shall be limited to the amount actually paid by you for the product. Some Jurisdictions do not allow the exclusion or limitation of liability for consequential or incidental damage. The above limitations may not apply to you in such jurisdictional cases.

Toll free: 1-877-536-3976

Local: 1-408-962-0515

13 atlona.com

Atlona Product Registration

Thank you for purchasing this Atlona product. - We hope you enjoy it and will take an extra few moments to register your new purchase.

Registration creates an ownership record if your product is lost or stolen and helps

At Atlona, we respect and protect your privacy, assuring you that your registration information is completely secure. Atlona product registration is completely voluntary and failure to register will not diminish your limited warranty rights.

To register go to: http://www.atlona.com/registration

Toll free: 1-877-536-3976

Local: 1-408-962-0515

14 atlona.com

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement