PRODUCT CATALOG Quality Products for Air Conditioning, Refrigeration & Heating Table of Contents Total System Protection 1-3 Coil Cleaners and Sprayers 4-10 Indoor Air Quality 11-14 Gas Leak Detectors 15 Refrigeration Oil & Vacuum Pump Oil 16-17 Aerosol Products 18-20 Specialty Products 21-22 Insulation Products 23 Glycol & Closed Systems 24-25 Water Treatment & Plumbing Products 26-30 Water Filtration Maintenance 31 Water Filtration 32-33 Nu-Plus by Everpure 34-39 Training Classes READY SET 40 Compatible with All Refrigerants & Oils Easiest to Install SEAL! Permanent Seal Takes seconds to inject. No injection hose or caulk gun needed. Concentrated formula means less material in the system. Total System Protection Total System Protection The Next Generation of Refrigerant Leak Sealant EasySeal® Direct Inject EasySeal Direct Inject is a new generation of sealants. Its innovative injection method makes it easier to install than other sealants. With this new injection system, pumping down the unit is a thing of the past. EasySeal Direct Inject works with all refrigerants and oils. Concentrated formula means less material in system. It is perfect for split systems, heat pumps, microchannel coils, packaged units, and mini splits. EasySeal Direct Inject is formulated to not plug cap tubes or expansion valves. EasySeal Direct Inject EasySeal Direct Inject bulk 6-pack EasySeal-SS Direct Inject 4050-08 4050-07 4050-05 A/C EasySeal® A/C EasySeal prevents and seals refrigerant leaks in residential and light commercial ACR systems. It is perfect for those hard-to-find and expensive-to-fix leaks and works with all refrigerants (except ammonia). It is easily installed with the reusable piercing valve and hose. A/C EasySeal circulates with the system’s refrigerant, and if a leak should occur, it will quickly and permanently seal the leak and prevent the system from losing refrigerant and shutting down. A/C EasySeal A/C EasySeal-SS “2+1” Display Pack A/C EasySeal-XL A/C Piercing Valve and Hose 3 ounce pressurized can - treats 1.5 to 5 ton systems 1.25 ounce pressurized can - treats fractional to 1.5 ton systems 2 cans of A/C EasySeal and an A/C Piercing Valve and Hose Treats systems with refrigerant charge of 125 lbs. – 250 lbs. 4050-06 4050-01 4050-02 4050-10 4051-99 A/C EasyDry This product is a quick and simple way to prevent and eliminate moisture in a system. A/C EasyDry contains a dehydrating agent that converts system moisture into a natural organic material that is compatible with and mixes with the lubricant. It is great for preventing acid formation, which is caused by moisture in a system, and it works with all refrigerants (except ammonia). Each can will treat up to a 5 ton system and is easily installed with the reusable piercing valve and hose. 3 ounce pressurized can A/C Piercing Valve and Hose 4051-06 4051-99 Visitus usatatwww.nucalgon.com www.nucalgon.comor orcall call1-800-554-5499 1-800-554-5499 Visit 11 Total System Protection Total System Protection Endorsed by York®, Goodman®, Nordyne®, Coleman®, and Daikin® Rx11-flush® R x11-flush is a unique solvent engineered specifically for flushing refrigeration and air conditioning systems. R x11-flush is ozone-safe, non-toxic, and non-flammable. Used exactly like the old R-11 flushing process, its patented HFC-based solvent formulation is powerful enough to flush away sludge, carbon residues, oils, acids, water and other particulates. R x11-flush is ideal for system flushing after burnouts, during retrofits and for flushing line sets for R-410A conversions. Rx11-flush has been the industry’s standard for over a decade, and contractors agree — it’s the best flush for R-410A retrofits and after compressor burnouts. Rx11-flush Starter Kit 1 lb. canister "2+1" Display Pack 2 lb. canister 13 lb. canister 26 lb. canister Contains a 1 lb. canister, Rx11-flush Gun and Hose, and Injection Valve Recommended for a 3-4 ton system Contains one Injection Valve and two 2 lb. canisters Recommended for a 5-7 ton system Recommended for up to 50 ton system Recommended for systems over 50 tons 4300-08 4300-09 4300-10 4300-11 4300-15 4300-26 Rx11-flush® Liquid R x11-flush Liquid is a new and improved chemistry that is the next generation in flushing technology. It remains a constant boiling solvent, and its stronger, fasteracting formula dissolves more oil, moisture and contaminants than any other flush. It is ideal for line sets, burnouts, and other flushing requirements. 19.5 ounce can Rx11-flush Liquid Starter Kit 4300-30 4300-38 Rx11-flush® Accessories The R x11-flush product family also includes various support tools. This includes the Injection Valve for hooking up to a charging hose for flushing and the Flushing Tool for facilitating line set flushing. In addition, the R x11-flush Gun with a built-in flushing attachment and the R x11-flush Hose (24˝) are available. Flushing Tool Rx11-flush Gun Rx11-flush Hose (24˝) Injection Valve 4300-50 4300-51 4300-52 4300-89 (Injection Valve fits Pneu-flush® and pressurized Rx-Acid Scavenger® as well) 2 A/C Re-New® A/C Re-New is a highly formulated, OEM approved product that has established an outstanding track record enhancing the performance of air conditioning and refrigeration systems. A/C Re-New frees sticky valves, quiets noisy compressors, reduces energy consumption by lowering starting and running amps, and improves heat transfer in the evaporator and condenser. It’s great for new systems as a preventative or to reinstate performance of older systems. 1 quart can 4 fluid ounce can A/C Re-New Injector Tool 4057-54 4057-55 4057-99 Rx-Acid Scavenger® The most effective way to neutralize or “scavenge” acid in refrigeration and air conditioning systems. It is perfect for use after burnouts or during normal on-going system maintenance. In addition, Rx-Acid Scavenger can be used with all lubricants: mineral, alkylbenzene and polyol ester. Now available in a pressurized can for easy injection into charged systems or hermetically sealed systems. 2 fluid ounce unpressurized bottle 3.8 ounce pressurized can Injection Valve 4301-02 4301-05 4300-89 (Injection Valve fits Rx11-flush® and Pneu-flush® as well) Phase III® Refrigeration Oil Acid Test Kit Formulated for use with POEs as well as mineral oils and alkylbenzene, Phase III is an inexpensive, disposable test kit that provides proof-positive that acid level in refrigeration oil is either safe or unsafe. Phase separation makes it easy to see change in color of acid indicator (even if a leak detection dye has been added to the oil). Just two bottles to work with, it is simple, safe, accurate, and small enough that you can carry several in your tool box. 1 each 4320-W8 How to Test Oil with Phase III® 1.Pour the solution from the small bottle into the large bottle. The bottom layer of this mixture will be purple. 2.Completely fill the small bottle with oil from the unit being tested. Do this immediately after the oil is removed from the crankcase, since exposure to air will contaminate the oil and give a false test result. 3. Pour the oil into the large bottle and shake well. 4. Wait two to three minutes. A phase separation will develop as the oil rises to the top of the mixture and an aqueous layer forms on the bottom. 5.If the bottom layer: Stays purple- the oil is satisfactory. Turns light pink or loses color completelythe oil has higher than acceptable acid content. Visit us at www.nucalgon.com or call 1-800-554-5499 Good Oil Bad Oil 3 Total System Protection Total System Protection Coil Cleaner Selection Guide Coil Cleaner Selection Guide Nu-Calgon Coil Cleaners Found on Pages 6-7 Nu-Brite® Foam-Brite® Alka-Brite® Plus CalClean® Special HD CalClean® TriClean™ 2x Nu-Solve™ NR • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Cal-Brite® Tri-Pow’r® HD EQUIPMENT USED ON • Condenser Coils • • • Mini-Split Condenser Coils • Small Condenser Coils • • Evaporator Coils Mini-Split Evaporator Coils • Small Evaporator Coils Microchannel Coils • Electronic Air Filters Fan Blades, Permanent Filters • • • • • • • • • • FORMULATED TO REMOVE Greasy Dirt & Oil • • • Cooking Grease • • • Lint, Dust, Dirt & Grime • • • • • • • • • • • • • • Alkaline Alkaline Alkaline • • • Tobacco Tars Oxide (Corrosion) Deposits • • • • Cottonwood/ Bugs • • • • • FEATURES & BENEFITS Product Type Alkaline Alkaline Alkaline Acidic Aerosol Liquid • • • • Brightening • • • • • Degreasing • • • • • Foaming • Alkaline Alkaline Aerosol Liquid • • • •* •* • • EPA Registered Disinfectant •* No Rinse (Evaporators) • No Rinse (Condensers) Biodegradable • • USDA Authorized • • • • • • • • • • • • U.S. EPA’s Safer Choice Program NSF Registered • • • • • • * Dilution ratios for no rinse applications: Tri-Pow’r HD = 10:1, Liquid CalClean = 10:1 (Aerosol CalClean must be rinsed), Special HD CalClean = 40:1, Green Clean = 10:1 4 Nu-Calgon Coil Cleaners Found on Pages 7-9 Evap-Powl’r®-C Evap-Fresh® No Rinse Cal-Green™ Evap-Green™ Green Clean Evap-Foam® Blackhawk® Nu-Blast® & Cal-Blast® CompleteCare Mini-Split Kit EQUIPMENT USED ON Condenser Coils • • • • Mini-Split Condenser Coils • • • • Small Condenser Coils • • • • Evaporator Coils • • • • • • • Mini-Split Evaporator Coils • • • • • • • Small Evaporator Coils • • • • • • • Microchannel Coils • • • • • • • • • • • • • • • • • • • • • • • Alkaline Alkaline Solvent Alkaline • • • Electronic Air Filters Fan Blades, Permanent Filters • FORMULATED TO REMOVE Greasy Dirt & Oil • • • • Cooking Grease Lint, Dust, Dirt & Grime • • • • • Tobacco Tars Oxide (Corrosion) Deposits Cottonwood/ Bugs FEATURES & BENEFITS Product Type Alkaline Alkaline Alkaline Alkaline Alkaline Aerosol Liquid • Foaming • Brightening • Degreasing EPA Registered Disinfectant No Rinse (Evaporators) • • • • • • • • •* • • Biodegradable • USDA Authorized • NSF Registered • • No Rinse (Condensers) U.S. EPA’s Safer Choice Program • • • • • • • • • • • • • Visit us at www.nucalgon.com or call 1-800-554-5499 • 5 Coil Cleaner Selection Guide Coil Cleaner Selection Guide Coil Cleaners Coil Cleaners Nu-Brite® Nu-Brite is the most effective coil cleaner available today. It foams, brightens, and is an equally effective yet safer alternative to HF acidbased products. It produces a high volume of foam that cleans more effectively than acids, particularly in removing grease. Biodegradable. The liquid versions are USDA approved and NSF registered. 18 ounce can 1 gallon bottle 2.5 gallon pail 55 gallon drum 4291-18 4291-08 4291-05* 4291-01 Foam-Brite® The ultimate in foaming alkaline cleaners, Foam-Brite cleans and brightens while at the same time providing tremendous foaming to push dirt and grime out of the coil. Can easily be used in place of the more dangerous HF acid-based products. Biodegradable. NSF registered. 1 gallon bottle 2.5 gallon pail 55 gallon drum 4178-08 4178-05* 4178-01 Alka-Brite® Plus A non-acid, alkaline based product for brightening and cleaning air-cooled condensers, AlkaBrite Plus contains the best available detergents to quickly penetrate and remove oxidation. Its foaming action helps to lift greasy soils out of the coil. Biodegradable. NSF registered. 1 gallon bottle 2.5 gallon pail 55 gallon drum 4120-08 4120-05* 4120-01 Cal-Brite® Cal-Brite is a low pH cleaner developed for cleaning evaporator coils, air-cooled condensers and other finned cooling and heating coils. Its versatility is based upon glycolic acid and other unique ingredients. It provides moderate foaming and brightening and is safe for use indoors as well as outdoors. It’s particularly suitable when lime scale must be removed from outdoor coils. 1 gallon bottle 55 gallon drum 4133-08 4133-01 * A 2.5 gallon pail wrench is also available. Part Number ZE64. 6 TriClean 2x™ The new way to clean a condenser coil. Simply connect to hose, clean, and rinse. TriClean 2x is metal-safe, designed for rapid emulsion of soils from the coil. Restores efficiency and is ideal for painted fin and microchannel coils. Eliminates the need for a sprayer. 1 quart sprayer with hose connector 4372-24 Nu-Solve™ NR Ready-to-use, non-rinse condenser coil cleaner for situations with limited water availability for rinsing. Nu-Solve NR is also for other applications where it is desirable to have less diluted cleaning solution on a commercial roof or when a solvent-based aerosol approach is not practical. Nu-Solve NR effectively emulsifies dirt and grime and provides a benefit of leaving a protective treatment on the aluminum for added corrosion protection, making the next cleaning easier. Nu-Solve NR can be applied with Nu-Calgon's poly sprayer or the Nu-Solve NR Sprayer (page 10). 1 gallon bottle 4295-08 Tri-Pow’r® HD An outstanding general purpose coil cleaner, providing detergency and degreasing as well as deodorizing capability. Its positive emulsion technology is very effective against oily grime as it converts the deposits into a more fluid or liquid form that can be easily rinsed away. It is nonacid, non-toxic, and biodegradable. NSF registered. Also great for microchannel coils. 1 gallon bottle 55 gallon drum 4371-88 4371-81 CalClean® An alkaline detergent formulated for cleaning evaporator coils, air-cooled condenser coils, metal filters, fan blades, and other surfaces soiled with grease, dust and dirt. Biodegradable. USDA approved. Aerosol is NSF registered. Also great for microchannel coils. 20 ounce can 1 gallon bottle 2.5 gallon pail 55 gallon drum 4081-75 4135-08 4135-06* 4135-01 Special HD CalClean® The best non-foaming cleaner available. Specifically formulated to remove tobacco tars from electronic air cleaners as well as the most stubborn deposits from finned coils. USDA approved. Also great for microchannel coils. 1 gallon bottle 2.5 gallon pail 55 gallon drum 4143-08 4143-06* 4143-01 * A 2.5 gallon pail wrench is also available. Part Number ZE64. Evap Pow’r®-C A no-rinse product formulated for cleaning evaporator coils. It is metal-safe, and it cleans and emulsifies even the most stubborn soils and deposits. Biodegradable. USDA approved. Also great for microchannel coils. 1 gallon bottle 2.5 gallon pail 55 gallon drum 4168-08 4168-05* 4168-01 Visit us at www.nucalgon.com or call 1-800-554-5499 7 Coil Cleaners Coil Cleaners Coil Cleaners Coil Cleaners Evap Foam No Rinse® Evap Foam No Rinse is a high-performing, heavy-duty detergent. It is formulated with special surfactants and alkaline cleaners that have been developed into a foaming, no-rinse product. Evap Foam is ideal for use on most coils, but it is particularly suited for use on cooling or evaporator coils. The aerosol can be sprayed either right side up or upside down. NSF registered. Can be used with Talon Flexible Aerosol Wand (4776-0) for hard to reach locations (see page 18). 18 ounce can 4171-75 Evap-Fresh® No Rinse Evaporator Coil Cleaner & Disinfectant Evap-Fresh is a ready-to-use, no-rinse cleaner and disinfectant for evaporator coils. It effectively cleans as well as kills mold and bacteria. This one-step no-rinse disinfectant cleaner is perfect for air conditioners, commercial air handling units, HVAC cooling coils, refrigeration equipment, and evaporator coils. EPA registered specifically for use on HVAC equipment. 18 ounce can 1 gallon bottle 4166-75 4166-08 The following products are part of Nu-Calgon’s Environmentally Friendly Green Select line. These coil cleaners meet the U.S. EPA Safer Choice Program standards, making them a safer choice for the user and the environment. Cal-Green™ Condenser Cleaner Cal-Green is a plant-based, natural condenser cleaner that is powerful enough to remove dirt, grease, and grime. It meets the U.S. EPA Safer Choice Program standards, making it a safer choice for the user and the environment. This non-foaming, non-toxic concentrate is perfect for cleaning residential or commercial systems and restores their efficiency while being environmentally responsible. Also OEM approved for microchannel coils. 1 gallon bottle 55 gallon drum 4190-08 4190-01 Evap-Green™ Evaporator Cleaner Evap-Green is a no-rinse product that is perfect for numerous heating and air conditioning applications, such as evaporator coils, roof top units, window units, metal filters, fan blades, and more. Evap-Green meet the U.S. EPA Safer Choice Program standards, making it a safer choice for the user and the environment . Evap-Green is also biodegradable and will not harm plants, animals, and aquatic life. Metal-safe — meets OEM guidelines for all aluminum coils, including microchannel types. 1 gallon bottle 55 gallon drum 4191-08 4191-01 Green Clean A pleasantly scented, all-purpose, environmentally friendly cleaner designed for the rapid removal of grease and other heavy soils. It can be used right out of the bottle or diluted for milder jobs. Biodegradable. Also great for microchannel coils. 1 quart spray bottle 1 gallon bottle 55 gallon drum 8 4186-24 4186-08 4186-01 Coil Cleaners Coil Cleaners Blackhawk® Blackhawk is an expanding foam coil cleaner. Formulated to deeply penetrate the coil, it liquefies to quickly remove grease, grime, or oily soils from deep within the coil. Blackhawk’s formulation is safe and problem-free for cleaning evaporator or condenser coils in an occupied building; produces no objectional fumes. It is particularly effective on coils on refrigerators, coolers, and freezers located in restaurants and other commercial establishments. NSF registered. Can be used with Talon Flexible Aerosol Wand (4776-0) for hard to reach locations (see page 18). 18 ounce can 4127-75 Nu-Blast® A no-rinse condenser coil cleaner in a convenient aerosol package. Double action of highpressure blast and solvent cleaning restores design efficiency of condenser coils. It is non-flammable and non-conductive. No rinse required — cleaning solvent evaporates completely. Use with adequate ventilation. 18 ounce can 4290-75 Cal-Blast® Cal-Blast is a no-rinse condenser cleaner that will powerfully separate undesirable materials from the surface, offering maximum cleaning of finned coils. It’s a high-performance aerosol with excellent solvency and blasting spray. 20 ounce can 4132-20 Coil Protectants NEW DuraCoil DuraCoil is a long-lasting coating for coils and surfaces in corrosive environments. It uses a durable, OEM-approved Heresite® Coating. DuraCoil has a fast, air-dry formula that bonds to all metals and causes negligible heat transfer loss across the coil. Great for repairing an OEM-approved coil coating that has been compromised while in service! Brown in color. 11 ounce can 4083-90 Cal-Shield® Cal-Shield is a synergistic liquid formulation based upon DuPont’s Teflon® fluoro-additives. It’s designed for application on air-cooled condensers, evaporator coils, and other finned heating and cooling coils. Cal-Shield will shield and protect the coil from adverse conditions. 1 quart spray bottle 1 gallon bottle 4148-32 4148-08 Nu-Shield® Nu-Shield, the newest generation of chemistry for protecting coils and other surfaces, is a super-hydrophobic (water repelling) product. The non-conductive formula has numerous applications in the management of water on non-food, non-potable water surfaces for the HVACR trade. Simply spray it on and watch the water bead up and roll right off. 9 ounce can Non-treated : Nu-Shield : Water Clings Water Repels 4294-75 Visit us at www.nucalgon.com or call 1-800-554-5499 9 Sprayers Sprayers NEW Coil Gun® Coil Mate™ Coil Cleaning Hose Nu-Solve NR Sprayer A “hose-end” sprayer that features five different mix ratio settings designed for coil cleaners. Utilizes a 2 quart capacity bottle and includes a foam wand as well as “quick disconnect” capability. The Coil Gun Probe accessory has a 90º direction of spray that allows cleaning from inside the coil. It also provides easy access in tough-to-reach locations. Durable 5/8 inch diameter reinforced hose with Flex-Guard protection. The 50-foot hose is equipped with solid brass wrench fittings. The Coil Mate is a necessity when using the popular Coil Gun® or rinsing an air-cooled coil with water after using a Nu-Calgon coil cleaner. Backpack-type sprayer developed for applying Nu-Solve NR, a non-rinse outdoor coil cleaner when water availability for rinsing is an issue. Sprayer utilizes a fourgallon tank with no holes or connections at the bottom to leak! Provides high-pressure spray for added cleaning effectiveness, large pressure chamber for lasting pressure, and a flexible and rugged wand with an adjustable spray nozzle. Replacement parts are available for all Nu-Calgon sprayers. Contact your local wholesaler. Coil Gun Coil Gun Probe 4774-0 4774-1 Coil Mate Hot Water Hose Plastic Pistol Grip Nozzle 61231 61238 61241 1 each 4775-0 No. 50P Poly Sprayer No. 100P Poly Sprayer No. 200P HiPressure Poly Sprayer The No. 50P is constructed of highdensity translucent polyethylene. It has a half gallon (3 pint) capacity. The nozzle is adjustable and the flow rate is controlled by a thumb lever. It comes with a 7˝ polyethylene pump. This sprayer is constructed of highdensity translucent polyethylene. It has a funnel top for easy chemical pouring and a 1 gallon working capacity. It comes with a 8˝ polypropylene pump, brass handle and extension tube with adjustable nozzle, a wear-resistant hose, and a pressure relief valve. The No. 200P HiPressure Poly Sprayer is constructed of high-density translucent polyethylene. It has a 2 gallon working capacity, funnel top, pump handle, and all-brass hardware. No pumping is required. Pressurize the sprayer with water through a “quick disconnect” fitting. 1 each 4770-0 1 each 4770-2 1 each 4771-2 No. 220CP Poly Sprayer No. 300P Poly Sprayer Multi-Purpose Sprayer The No. 220CP Poly Sprayer is constructed of high-density translucent polyethylene with a funnel top that provides easy chemical pouring. This 2 gallon capacity sprayer features an easy fill level indicator and comes with an 8˝ pump and a high resin plastic adjustable nozzle with three feet of hose. 1 each 4771-3 The No. 300P Poly Sprayer is constructed of high-density translucent polyethylene. It has a funnel top and a 3.5 gallon capacity (3 gallon working capacity). It comes with a 10˝ Celcon pump, brass extension tube with adjustable nozzle, and five feet of vinyl hose. A 24 ounce capacity sprayer. It is ideal for small cleaning jobs, such as window units and water coolers. 10 1 each 4772-0 1 each 4768-W3 Evap-Fresh® No Rinse Evaporator Coil Cleaner & Disinfectant Evap-Fresh is a ready-to-use, no-rinse cleaner and disinfectant for evaporator coils. It effectively cleans as well as kills mold and bacteria. This one-step no-rinse disinfectant cleaner is perfect for air conditioners, commercial air handling units, HVAC cooling coils, refrigeration equipment, and evaporator coils. EPA registered specifically for use on HVAC equipment to kill H1N1 and other viruses such as Norwalk, Rhoto, Hepatitis, Rabies MRSA, and more. 18 ounce can 1 gallon bottle 4166-75 4166-08 CompleteCare Mini-Split Kit The CompleteCare Mini-Split Kit cleans, disinfects, and deodorizes mini-splits, as well as controls mold and mildew. It also protects condensate pans and lines from plugging. Each kit treats 2-3 mini-splits. Contains one 18 oz. can of Evap-Fresh No Rinse and one PurCool® Green Mini Strip. 1 each 4151-08 Bio-Fresh® cd A ready-to-use bacteriostatic, fungistatic, and deodorizer based upon chlorine dioxide technology. Inhibits the growth of bacteria, mold, mildew, fungi, and yeasts in IAQ applications, and it may be applied to occupied spaces. Its EPA registration applies to HVACR ventilating equipment, including coils, condensate pans, filters, and duct-work. Easily applied by spraying, brushing, sponging, or wiping. EPA registered. 1 quart spray bottle 1 gallon bottle 4126-34 4126-38 Bio-Fresh® Fogger The Bio-Fresh Fogger is made of a one-piece, seamless heavy-duty copolymer. It uses a 48˝ flexible hose and is adjustable from 0-18 ounces per minute with the respective particle size at 20 to 80 microns. It’s ideal for spraying Bio-Fresh cd in duct work and large areas. 1 each 4693-0 Drain Solve Ideal for condensate pan drains. Drain Solve saves time and money with its ease of use. It eliminates application concerns associated with more reactive, fuming drain openers. Simply pour it down the drain and let it work without fear of noxious fumes or reactions. Does not contain sulfuric acid. 1 quart 1 gallon 4165-24 4165-08 A/C Drain Sucker® A/C condensate drain pan overflow is caused by slime and sludge that builds up and clogs the drain line. The A/C Drain Sucker quickly removes the clog and the excess water, resolving the overflow problem. The kit includes a PurCool® Pan Strip to provide months of preventive treatment and free flowing drains, as well as all fittings and hoses for suction or pressure applications. Nu-Calgon Number ClenAir Number A/C Drain Sucker kit 61308 CADS1 PurCool Pan Strip - treats 3 tons - 6 mos. 61043 1903D Visit us at www.nucalgon.com or call 1-800-554-5499 11 Indoor Air Quality Indoor Air Quality Indoor Air Quality Indoor Air Quality: ClenAir by Nu-Calgon The Original ClenAir™ Odor Neutralizer ClenAir’s unique odor neutralizing formula removes odors quickly and permanently. It is a true odor eliminator, not a mask. Originally designed for use in central air systems, on fire and flood restoration jobs and in sewage facilities, ClenAir is a professional product, yet it leaves no lingering antiseptic or perfume smell. It is great for odors caused by fuel oil, smoke, pets, mold and mildew, cigarette and cigar smoke, decay, cleaning solvents and even skunks. ClenAir has three different scents: Original, CherryAir, and OrangeAir. The scents come in multiple sizes for multiple applications. Original Mini Tub 1/2 lb. Tub display box 1/2 lb. Tub 1 lb. Tub 3 lb. Tub CherryAir Mini Tub 1/2 lb. Tub display box 1 lb. Tub OrangeAir Mini Tub 1/2 lb. Tub display box 1 lb. Tub Nu-Calgon ClenAir 61000 61001 61002 61003 61004 CA1500M 1500D 1500 1501 1503 Nu-Calgon ClenAir 61018 61010 61011 CA1800M 1800D 1801 Nu-Calgon ClenAir 61028 61020 61021 CA1300M CA1300D CA1301 Original 10 lb. Tub 30 lb. Tub Wall Unit (White) Nu-Calgon 61005 61006 61007 Gel Brick for Wall Unit (1lb.) 61008 CherryAir 3 lb. Tub 10 lb. Tub 30 lb. Tub OrangeAir 3 lb. Tub 10 lb. Tub 30 lb. Tub ClenAir 1510 1530 1300 1401 Nu-Calgon ClenAir 61013 61015 61017 1803 1810 1830 Nu-Calgon ClenAir 61023 61025 61027 CA1303 CA1310 CA1330 HVAC Odor Block® ClenAir HVAC Odor Block is not a perfume mask or cover-up. The unique ClenAir formula molecularly reacts with the airborne odor-causing compounds and eliminates them and other indoor pollutants, leaving clean, fresh, air behind. The HVAC Odor Block makes it easy to remove odors and improve the indoor air quality in the entire home or building by treating the air through the HVAC system. Use in A/C units, furnaces, rooftop units, fan coil units, and air handlers. Part numbers 61060 and 61061 last up to 3 months. The HVAC Odor Block XL (61070) lasts up to 6 months. Side Vent for Carbon Filtration Nu-Calgon Number 61060 61070 61061 Residential HVAC Odor Block Residential HVAC Odor Block XL Commercial HVAC Odor Block ClenAir Number 1502 CA1015 ClenAir Liquid Formula ClenAir Liquid is a fast acting deodorizing product. It eliminates odors via an oxidation process while leaving a fresh scent. Applications include HVACR equipment, such as evaporator coils, duct work, condensate pans, refrigeration cases, reach-ins, and walk-in boxes. It can also be poured down drains, garbage disposals, and in trash cans. Spray in restrooms, locker rooms and on fouled carpeting and upholstery. Used by hospitals, nursing homes, and HVACR technicians. Nu-Calgon Unscented Spray 16 oz. 61030 Unscented Liquid 1 gal. 61031 Citrus Spray 16 oz. 61033 12 ClenAir 1600D 1610 1700D Citrus Liquid 1 gal CherryAir Spray 16 oz. CherryAir Liquid 1 gal. Nu-Calgon ClenAir 61035 61037 61038 1710 1900D 1910 Indoor Air Quality Indoor Air Quality NEW Gel Tabs - Condensate Drain Pan Treatment Formulated with a breakthrough technology for treating air conditioning drain pans and lines. Keeps the drain pan from clogging and eliminates foul and musty odors. When activated by condensation, the tablet will turn to gel and lock into place. Dissolves continuously and completely with nothing left to remove for up to three months. Stack together to increase duration. 3 ton tab (12 in tube) 3 ton tab bulk (200) 5 ton tab (6 in tube) 4185-03 4185-04 4185-05 5 ton tab bulk (100) 15 ton tab (1 each) 20 ton tab (1 each) 4185-06 4185-15 4185-20 PanPads A product formulated to eliminate the build-up of bacteria and slime growths in air conditioning and refrigeration condensate drain pans. In laboratory tests, it has been proven effective against a wide spectrum of harmful bacteria, including Legionella. The product is EPA registered for this application. NSF registered. 5 (up to 5 tons) 4295-34 5 Slim (up to 5 tons) 4295-36 15 (up to 15 tons) 45 (up to 45 tons) 4296-24 4296-45 Pan-Treat® Pan-Treat condensate tablets control odors and prevent overflows caused by plugged condensate drain lines. They can also be used in humidifiers. They are very easy to use, as well as non-corrosive, non-toxic, and biodegradable. 1 bottle (200 tablets) 4296-60 PurCool® Strips PurCool Strips keep A/C and refrigeration condensate drain pans clean and free flowing. Use PurCool Strips to prevent condensate drain clogs, costly overflows, and corrosion. Just place them anywhere in the drain pan where the PurCool Strip will contact the condensate water and enjoy up to six months of economical protection. PurCool Strips will adhere to the drain pan and will not float or move. Dissolves completely, leaving no residue. Safe for metal and plastic drain pans. Nu-Calgon ClenAir 3 ton strip 61043 3 ton strip bulk (100) 61047 5 ton strip 61042 1903D 1903D-100 2001D 10 ton strip 30 ton strip Visit us at www.nucalgon.com or call 1-800-554-5499 Nu-Calgon ClenAir 61041 61040 2003D 2009 13 Indoor Air Quality Indoor Air Quality: ClenAir by Nu-Calgon PurCool® Green Strips and Tablets PurCool Strips/Tablets prevent slime, sludge, odors, and overflow of condensate pans. Time release formula adheres to pan and fully dissolves over time. PurCool Green Strips/Tablets use plant-based suspending and dispersing action to keep drain pans clean and free flowing. Products are available for commercial, residential, and mini split applications. Sizes are based on system tonnage, with each strip/tablet lasting up to six months. PurCool Green Mini Strip PurCool Green Commercial Strip 10 ton PurCool Green Commercial Strip 30 ton PurCool Green 3 ton tablet PurCool Green 3 ton bulk (200) PurCool Green 5 ton tablet PurCool Green 5 ton bulk (100) Nu-Calgon Number 61044 61045 61046 61048 61049 61051 61052 ClenAir Number PCG5MS PCG10T PCG30T PCG5T PCG5T-100 PurCool® Tablets PurCool Tablets utilize a powerful formulation to keep condensate drain pans clean and free flowing. Use PurCool Tablets to remove sludge and slime in A/C condensate pans to prevent costly water damage caused by overflows. They will control clogs, build-up, odors, and corrosion in drain pans, condensate pumps, and humidifiers. Nu-Calgon Number 61053 1 bottle (200 tablets) ClenAir Number PC200 HVAC Carbon Block® In-Duct Air Purification System HVAC Carbon Block is an add-on carbon purifier for all HVAC systems. Improves indoor air quality by removing odors, indoor air pollutants, and VOCs. Treats up to 10 tons for up to nine months. Nu-Calgon Number 61062 HVAC Carbon Block ClenAir Number CACB10 Humidifier Panel™ Replacements ClenAir Universal Humidifier Panels provide optimum moisture output, performance, and durability. They replace Aprilaire, Honeywell, Carrier, Bryant, Lennox, ICP, and others. Ultra Upgrade Humidifier Panels' material retains water, increasing moisture output and reducing water waste by up to 50%. They replace Aprilaire, Honeywell, Carrier, Bryant, Lennox, ICP, and others. Universal Humidifier Panel - #10 size Universal Humidifier Panel - #12 size Universal Humidifier Panel - #35 size Ultra Upgrade Humidifier Panel - #10 size Ultra Upgrade Humidifier Panel - #35 size Nu-Calgon Number 61250 61251 61252 61254 61255 ClenAir Number CA10 CA12 CA35 CA10UP CA35UP Spacegard® Filter Media Replacements These Merv 11 filter media are direct replacements for the Aprilaire Spacegard 201 and 401. Merv 11 media removes pollen, allergens, smoke, dust, dust mites, bacteria, spores, and pet dander. The large filter surface area provides for low resistance and longer filter life, more than 6 months! Nu-Calgon Number Replacement for Aprilaire Spacegard 201 61256 Replacement for Aprilaire Spacegard 401 61257 ClenAir Number CA201 CA401 *Aprilaire and Spacegard are registered trademarks of Research Products Corporation 14 Gas Leak Detectors Gas Leak Detectors Cal-Blue® Plus Gas Leak Detector Cal-Blue Plus is a complete gas leak detector with freeze protection to 5˚F. Its high viscosity formula enables it to remain in contact with the applied surface for an extended period of time, allowing it to detect the smallest of leaks. The longest lasting bubbles in the industry! It is also non-corrosive to metal, and it will not affect ultraviolet or black lights. NSF registered. 6 ounce bottle with dauber 1 quart spray bottle 1 gallon bottle 4182-53 4182-24 4182-08 Cal-Blue® LT Gas Leak Detector The same high quality formulation as regular Cal-Blue Plus, but it has added freeze protection to -20˚F. It is the ideal detector for geographical areas that may experience very cold temperatures. The longest lasting bubbles in the industry! NSF registered. 1 quart spray bottle 1 gallon bottle 4183-24 4183-08 Gas Leak Detector The original industry leak detector. A high viscosity liquid that forms bubbles when daubed on a gas leak. Non-corrosive, non-staining, and harmless to skin. Detects any type of gas leak, such as air, compressed air, carbon dioxide, nitrogen, natural gas, and refrigerant gases. Freeze protection to -20˚F. Six ounce plastic bottles have dauber in cap. USDA approved. 6 ounce bottle with dauber 4180-53 Fluorescent Gas Leak Detector A fluorescent formulation that provides improved visibility and long lasting bubbles. It is non-corrosive to metals and is freeze protected to 5˚F. Suitable for high and low temperature applications. Can be used for most refrigerants, natural gas and oxygen systems. USDA approved. 8 ounce bottle with dauber 1 quart spray bottle 1 gallon bottle 4184-53 4184-24 4184-08 AccuTrak® Ultrasonic Leak Detector Model VPE - Now with touchprobe included. Patented technology detects the ultrasonic sound of a leak! Nu-Calgon Number ClenAir Number AccuTrak® Ultrasonic Leak Detector 61307 CAVPE Visit us at www.nucalgon.com or call 1-800-554-5499 15 Refrigeration Oil & Vacuum Pump Oil Polyol Ester (POE) Lubricant Emkarate® RL Lubricant The Emkarate family of polyol ester refrigeration lubricants are designed specifically for use with HFC refrigerants. They are available in a range of viscosities. They have excellent thermal and chemical stability, and they are compatible with a wide range of elastomers, polymeric materials, and other materials of construction. Fully miscible and compatible with mineral oils and alkylbenzene lubricants as well as with CFCs, HCFCs and HFCs. Emkarate RL 22H 32H 32HB 32-3MAF 46H 68H 68HB 68HP 100E 100H 170H 220H+ 220XL Viscosity 100 SUS 150 SUS 150 SUS 150 SUS 200 SUS 300 SUS 300 SUS 300 SUS 500 SUS 500 SUS 850 SUS 1100 SUS 1100 SUS 1 Quart 4314-44 4314-64 4316-44 1 Gallon 4313-46 4314-46 4314-66 4315-46 4316-46 4316-86 4316-76 4317-66 4317-46 4318-26 4318-66 5 Gallon 53 Gallon 4314-45 4314-62 4314-65 4314-41 4314-67 4315-41 4316-41 4316-45 4316-85 4316-71 4318-25 4318-65 4318-75 4318-21 4318-61 Mineral Oil C-3s, C-4s, C-5s Refrigeration Oil These are mineral naphthenic lubricants manufactured by Calumet Lubricant Company and available in three viscosities. They are specifically designed for today’s high performance air conditioning and refrigeration compressors using CFC and HCFC refrigerants. These compressors run at higher speeds and generate higher temperatures, and as a result, they require better lubrication. Use of these oils will ensure continued efficient operation. Nu-Calgon C-3s C-4s C-5s Viscosity 150 SUS 300 SUS 500 SUS 1 Gallon 4303-07 4304-07 4305-07 5 Gallon 4303-05 4304-05 55 Gallon 4303-01 4304-01 4305-01 Polyvinyl Ether (PVE) Lubricant Idemitsu Polyvinyl Ether Lubricant PVE lubricants provide for increased stability and lubrication. They do not hydrolyze in the presence of moisture, a very important feature in HVACR applications. Additionally, they are compatible with other refrigeration oils and process fluids. PVE lubricants also exhibit compatibility and performance with frequently used anti-wear additives. Idemitsu FVC32D FVC68D 16 Viscosity 32 SUS 68 SUS 1 Quart 4319-14 4319-24 Zerol® Alkylbenzene Refrigeration Oil Zerol Refrigeration Oil is recommended for use in all refrigeration and air conditioning applications using CFC and HCFC refrigerants. It is highly recommended by refrigerant and compressor manufacturers for use with R-22 and other HCFC blends such as R-409A as it provides many distinct advantages: excellent miscibility, excellent thermal stability, and low temperature performance compatibility with mineral oils. It is the oil of choice for R-22 and R-502. Zerol 150 200TD 300 400CA 500 Viscosity 150 SUS 200 SUS 300 SUS 400 SUS 500 SUS 1 Gallon 4310-07 4308-07 4311-07 5 Gallon 4311-05 4311-65 4312-05 55 Gallon 4310-01 4308-01 4311-01 Vacuum Pump Oil Vacuum Pump Oil Nu-Calgon’s Vacuum Pump Oil is a quality, high-grade lubricant that performs at the deepest vacuum. It has a very low vapor pressure, and it has excellent lubricity for complete surface protection. It contains no additives or detergents. 1 pint bottle 1 quart bottle 1 gallon bottle 4383-34 4383-24 4383-07 Refrigeration Oil Products Refrigeration Oil Charging Pump An oil pump for charging refrigeration oil into a system, even while it’s running. This pump can be used for 1 gallon, 2.5 gallon, and 5 gallon containers. Incorporates an automatic bleed valve that keeps pressure equalized inside the container and includes a tapered rubber adapter that fits all container openings without the need for additional adaptors. 1 each 4814-40 Total Lube Refrigeration Oil Test Kit Have a professional lab analyze the oil to help detect potential problems such as metal wear or burnouts. The analysis will provide information on the oil’s moisture, total acid number, viscosity, color, and spectrochemical analysis on 20 plus metals and compounds. Help prevent potential downtime, burnouts, and costly oil changes by incorporating regular testing of the refrigeration oil. 1 each 4996-0 Oil Refractometer A precision optical instrument that allows for the rapid and accurate determination of the refractive index of oil solutions. It will specifically assist in determining the percent of residual oil remaining in a refrigeration system when converting it to a new refrigeration oil. Such retrofits require converting the mineral oil to a polyol ester (POE) or polyalkylene glycol (PAG), an alkylbenzene lubricant (Zerol®) to a POE, or a mineral oil to an alkylbenzene. 1 each 4815-0 CanVerter® A hand-held pump used to remove or add oil to hermetic compressors. Easy to use; each stroke pumps 1 ounce of oil. 1 each 4814-0 Visit us at www.nucalgon.com or call 1-800-554-5499 17 Refrigeration Oil & Vacuum Pump Oil Alkylbenzene Oil Aerosol Products Aerosol Coil Cleaners NEW Evap Foam No Rinse® Evap Foam No Rinse is a high-performing, heavy-duty detergent. It is formulated with special surfactants and alkaline cleaners that have been developed into a foaming, no-rinse product. Evap Foam is ideal for use on most coils, but it is particularly suited for use on cooling or evaporator coils. The aerosol can be sprayed either right side up or upside down. NSF registered. Can be used with the Talon Flexible Aerosol Wand (4776-0) for hard to reach locations. 18 ounce can 4171-75 Talon Flexible aerosol wand for Nu-Calgon’s Evap Foam No Rinse, Blackhawk or PenetrateHD products. Provides focused cleaner spray or penetrant in tough-to-reach locations. The Talon is highly flexible, retains shape memory, and provides 27 inches of added length to an aerosol canister for navigating in tight quarters inside the equipment. The reusable Talon is a must-have service tool! 1 each Nu-Brite® Evap-Fresh® No Rinse Nu-Brite is a very effective degreaser and cleaner on condenser coils. Its high foaming characteristic will help push soil deposits out of the coil, leaving it clean and bright. With proper ventilation, it can also be used as a kitchen degreaser by emulsifying stubborn, resistive grease deposits found on coils located in kitchens. Product should be used where adequate rinsing is possible. Evap-Fresh is a ready-to-use, no-rinse cleaner and disinfectant for evaporator coils. It effectively cleans as well as kills mold and bacteria. This one-step no-rinse disinfectant cleaner is perfect for air conditioners, commercial air handling units, HVAC cooling coils, refrigeration equipment, and evaporator coils. EPA registered specifically for use on HVAC equipment. 18 ounce can 4291-18 18 ounce can 4166-75 Cal-Blast® Nu-Blast® Cal-Blast is a no-rinse condenser cleaner that will powerfully separate undesirable materials from the surface, offering maximum cleaning of finned coils. It’s a high-performance aerosol with excellent solvency and blasting spray. A no-rinse condenser coil cleaner in a convenient aerosol package. Double action of high-pressure blast and solvent cleaning restores design efficiency of condenser coils. It is non-flammable and non-conductive. No rinse required — cleaning solvent evaporates completely. Use with adequate ventilation. 20 ounce can 4132-20 18 ounce can Blackhawk® Blackhawk is an expanding foam coil cleaner. Formulated to deeply penetrate the coil, it liquefies to quickly remove grease, grime, or oily soils from deep within the coil. Blackhawk’s formulation is safe and problem-free for cleaning evaporator or condenser coils in an occupied building; produces no objectional fumes. It is particularly effective on coils on refrigerators, coolers, and freezers located in restaurants and other commercial establishments. NSF registered. Can be used with the Talon Flexible Aerosol Wand (4776-0) for hard to reach locations. 18 ounce can 18 4776-0 4127-75 4290-75 CalClean® CalClean is a heavy-duty detergent formulation of surfactants, grease solvents, alkaline cleaners, corrosion inhibitors, and water conditioners. Ideal for cleaning window units as well as small evaporator coils, air-cooled condenser coils, metal filters, fan blades and other surfaces soiled with greasy dust and dirt. NSF registered. 20 ounce can 4081-75 NEW Nu-Shield® Nu-Shield, the newest generation of chemistry for protecting coils and other surfaces, is a super-hydrophobic (water repelling) product. The non-conductive formula has numerous applications in the management of water on non-food, non-potable water surfaces for the HVACR trade. Simply spray it on and watch the water bead up and roll right off. 9 ounce can 4294-75 DuraCoil DuraCoil is a long-lasting coating for coils and surfaces in corrosive environments. It uses a durable, OEM-approved Heresite® Coating. DuraCoil has a fast, air-dry formula that bonds to all metals and causes negligible heat transfer loss across the coil. Great for repairing an OEM-applied coil coating that has been compromised while in service! Brown in color. 11 ounce can 4083-90 A/C Shine® Superior Cleaner / Protectant Pan-Spray® A/C Shine is specially formulated to clean and protect the painted metal surfaces of outdoor A/C condensing units. It sprays on and wipes off quickly and easily without water. For use on all outdoor unit painted surfaces. Pan-Spray is an effective, easy-to-use waterproof rubberized coating that won’t chip, flake, or peel. It’s ideal for sealing out rust and corrosion as well as repairing leaky condensate pans, cooling towers, swamp coolers, roofing, gutters, and down spouts. Pan Spray is the perfect solution for emergency and permanent repair. 12 oz. Nu-Calgon Number ClenAir Number 61118 ACS12 16 ounce can - White 16 ounce can - Black 4296-50 4296-51 Aerosol Lubricants Break-n-Lube™ Food-Grade Silicone This advanced technology 4-in-1 product is made with CERFLON® for high performance in a non-drying penetrating lubricant. It’s highly versatile with the ability to penetrate, lubricate, displace moisture, and provide superior resistance to corrosion. It’s specially formulated to help free rusted parts and assemblies. Food Grade Silicone sprays a perfect non-stick surface on ice machine surfaces, vending machines, coin slots, slicing machines, dairy machinery, and other food processing and packaging equipment. An excellent lubricant that prevents binding and sticking. Contains ingredients approved by the FDA for food contact use. USDA approved. 12 ounce can 4128-03 11 ounce can 4084-03 PenetrateHD® Super Penetrating Lubricant V-Belt Dressing Loosens rusted and frozen metal parts. Frees stuck fan blades, blower shafts, pulleys, rusted nuts and bolts, and any frozen, rusted, or seized metal part. Unique low surface tension formula penetrates into the smallest spaces and breaks and dissolves the bonds of rust and corrosion. Lubricates and protects metals. Dielectric strength 40,000 volts. Can be used with the Talon Flexible Aerosol Wand (4776-0) for hard to reach locations. V-Belt Dressing is specially formulated to penetrate and extend modern V-Belt life. It is particularly effective in maintaining V-Belt efficiency and performance under today’s increasing performance requirements. It keeps belts pliable, prevents slippage, and does away with squealing and chattering. USDA approved. 12 ounce can 17 ounce can 12 ounce can - LV* 17 ounce can - LV* 11 ounce can 4086-03 61105 61106 61107 61108 * LV = Low VOC for California Visit us at www.nucalgon.com or call 1-800-554-5499 19 Aerosol Products Aerosol Specialty Products Aerosol Products Aerosol Adhesives Spray-n-Bond™ Spray Adhesive A wide web spray adhesive formulated specifically for insulation and duct liner applications. Ideal for porous surfaces, it is waterproof, flexible, transparent, non-staining, and it can be used for both temporary or permanent bonds. Formulated with the environment in mind, it contains no chlorinated solvents or ozone depleters, and it is VOC-compliant in states such as California. Spray Adhesive is a fast-drying, all-purpose product that provides a strong, water-resistant, flexible bond. It is translucent and does not penetrate or soak material causing bleed-through. Spray Adhesive is excellent for labeling, bonding, splicing and sealing paper, cardboard, cloth, rubber, styrofoam, canvas, leather, wood, and most plastics. 12 ounce can 12 ounce can 4080-04 4369-75 Aerosol Specialty Products Pipe-Dri® Nu-Kill® II Wasp and Hornet Killer Aerosol insulation that provides a moisture barrier to stop sweating and dripping on refrigeration lines, air conditioning lines, and other cold surfaces. Quickly adheres and dries to a hard waterproof coating. Pipe-Dri makes it possible to insulate hard-to-reach areas. A “quick-kill” spray formulation EPA registered to instantly and effectively kill wasps, hornets, and yellow jackets, from distances up to 20 feet. Nu-Kill II also kills with residual action as wasps and hornets return to a treated nest. The formula is safe in and around electrical equipment, having a dielectric strength of 47,000 volts. 18 ounce can 4297-75 13.5 ounce can Pump Protector Zinc Rich Cold Galvanizing When corrosion occurs in close-tolerance areas, it can cause the impeller to stick or bind. Pump Protector protects seasonally operated pumps against corrosion during shutdowns by winterizing them. It is safe for all types of water pumps and requires no special rinsing at start-up. Highly resistant to nearly all forms of corrosion. Perfect for repairing factory galvanized material damaged in shipment, welding, assembly, etc. Its 95% pure zinc film fuses itself to iron, steel, or aluminum. Blends well with hot-dip coating. Meets or exceeds military specifications MIL-P- 26915A, MIL-T- 26433, MIL-P- 21035, MIL-P-46105 and the Preece Test. 10 ounce can 4299-T8 13 ounce can 4087-03 Electrical Contact Cleaner Degreasing Solvent EF Cleans, lubricates, and protects electrical contacts from corrosion, and it is safe on most plastics. Cleaning action quickly removes greases, dust, and oxidation, restoring and maintaining precision and efficiency to the instrument and component. Includes extension tube for pinpointing application. USDA approved. A degreasing solvent, specially formulated for cleaning and degreasing equipment where washing or flushing is not possible. Simply spray on and wipe off. Penetrates quick and deep, loosening and liquefying heavy greases and tar. Non-corrosive and non-staining with a dielectric strength over 26,000 volts. 11 ounce can 14 ounce can - LV * 4082-03 4082-04 * LV = Low VOC for California and Canada 20 4292-75 14 ounce can 14 ounce can - LV* 4083-75 4083-83 * LV = Low VOC for California Great Wipes Great Wipes Industrial Strength Hand Towels are waterless wipes made specifically for the air conditioning, refrigeration, and plumbing service technician. Each premoistened, heavy duty towel has strong pumice scrubbing power that conveniently cleans anywhere and anytime. 75 count canister 4185-75 Scrubs-In-A-Bucket® HVAC80 The original Scrubs — disposable, pumice-performance waterless hand cleaner towels that effectively and quickly clean hands on a wide variety of industrial soils and greases. Each selfdispensing portable canister contains 80 perforated disposable heavy-duty towels and are pre-moistened with the famous Scrubs cleaning formulation. Effective yet gentle to the skin. Use anywhere, anyplace, anytime. 30 count canister 80 count canister 4366-24 4366-87 Quick Seal™ Pipe Repair A permanent knitted fiberglass impregnated tape that is designed for quick, in-the-field repair of leaks for all types of pipes. It can be used on both cold or hot water as well as refrigeration, plumbing, industrial, commercial, and residential applications. It is safe for potable water and is UL listed. ANSI/NSF Standard 61. 2˝ x 3´ wrap 4˝ x 12´ wrap 4299-10 4299-11 Pneu-flush® A flushing and cleaning system specifically designed for pneumatic control air lines. It utilizes DuPont® Vertrel® XM, a premier ozone-safe HFC cleaning solvent. Pneu-Flush works quickly and easily to clean and purge the compressed air lines in HVAC control and other pneumatic systems. 2 lb. canister Injection Valve 4298-01 4300-89 (Injection Valve fits Rx11-flush® and Pressurized Rx-Acid Scavenger® as well) Thermo-Trap® The industry’s original heat absorbing paste designed to isolate heat encountered in soldering, welding, and brazing, thereby preventing damage to nearby heat sensitive controls, or fittings. USDA approved. Biodegradable. Available in paste or gel. Thermo-Trap paste Thermo-Trap gel Thermo-Trap gel 11 ounce tube 1 quart spray bottle 4 fluid ounce spray bottle 4371-36 4371-32 4371-53 Degreasing Solvent EF Degreasing Solvent EF is a volatile solvent, especially formulated to provide effective cleaning and drying and reduce safety hazards. It leaves surfaces clean and oil-free. The thorough cleaning action is superior to ordinary chlorinated solvents. 1 gallon 1 gallon - LV* 4162-07 4162-17 * LV = Low VOC for California Visible Defects Heat Exchanger Inspection System The Visible Defects Heat Exchanger Inspection System is a complete kit that enables the technician to better evaluate the integrity of a heat exchanger. If a crack exists, the specially formulated fluorescent penetrant visually enhances the crack, allowing the technician to see the defect easier. Visible Defects kit Crack Finder replacement solution 4385-00 4385-06 Visit us at www.nucalgon.com or call 1-800-554-5499 21 Specialty Products Specialty Products Specialty Products General Purpose Cleaners Green Clean A pleasantly scented, all-purpose, environmentally friendly cleaner designed for the rapid removal of grease and other heavy soils. It can be used right out of the bottle or diluted for milder jobs. Biodegradable. Also great for microchannel coils. 1 quart spray bottle 1 gallon bottle 55 gallon drum 4186-24 4186-08 4186-01 Spray Nine® Cleaner & Disinfectant Spray Nine is a tough task cleaner and broad spectrum disinfectant. EPA-registered Disinfectant kills harmful germs like HIV-1, Influenza, H1N1, Staphylococcus Aureus, Salmonella Choleraesuis and E. Coli in 45 seconds. Also helps prevent cross contamination. Authorized by USDA for use in federally inspected meat and poultry plants with a C-1 rating. Nu-Calgon Number 61110 61113 1 gallon 32 oz. spray ClenAir Number 26801 26832 Grez-Off® Heavy Duty Degreaser Grez-Off works hard so you don’t have to. This heavy-duty answer to heavy-duty grease and grime leaves engines, machinery, asphalt, garage floors and more whistle clean. Biodegradable, non-flammable formula hits hard and fast with less impact on user and environment. Nu-Calgon Number 61116 61117 1 gallon 32 oz. spray ClenAir Number 22701 23732 Other Specialty Products Elite® Performance Windshield Washer Cleaner -20° Elite Performance Windshield Washer is independently tested to provide freeze protection to -20°F. Don’t take chances with generic washer products; only Elite Performance offers certified protection. Nu-Calgon Number 61115 1 gallon ClenAir Number CAWW1G ClenHands: Orange Smoothie™, Orange Crush™ and Cherry Crush™ Premium antimicrobial hand cleaners that quickly dissolve dirt, grease, fuel oil, pipe dope, resin, ink, paint, glue, rubber gasket and tile cements and many other hard-to-remove soils. ClenHands Orange Smoothie is a smooth non-pumice formula, while ClenHands Orange Crush is enhanced with fine-ground American pumice. ClenHands Cherry Crush is a cherry-scented antimicrobial hand cleaner with pumice. For use with or without water. Orange Crush with Pumice Orange Smoothie Non Pumice Orange Crush with Pumice Cherry Crush with Pumice ClenHands Super Gel 1 gallon 15 ounce 15 ounce 15 ounce 11 ounce Nu-Calgon Number 61201 61202 61203 61204 61205 ClenAir Number 2201 2202 2215 2315 2414 Smoke Signal™ Smoke Candles and Smoke Pens Smoke Signal generates smoke by chemical reaction, eliminating costly equipment and time to pinpoint leaks. Smoke tests will effectively and inexpensively reveal leaks in heating and air conditioning duct work, furnaces, fire boxes, exhaust fans and smoke detectors. Smoke Pens are also excellent for observing ventilation, air balancing, smoke detectors, drafts, leakage, and air flow. The Smoke Pens come with one pen, six replacement wicks (refills available) and instructions. Smoke Signal items contain no explosive materials. Smoke Candle - 4000 cubic feet of smoke 30 sec. - 1A Smoke Candle - 8000 cubic feet of smoke 60 sec. - 2B Smoke Candle - 40,000 cubic feet of smoke 2-3 min. - 3C Smoke Pen Refill Package - 6 wicks 22 Nu-Calgon Number 61302 61303 61304 61305 61306 ClenAir Number CAS30 CAS60 CAS180 CASP1 CASP1RW Perma-Wrap™ Foam Insulation Tape Formulated from the highest quality elastomeric thermal insulation material. Its closed cell construction seals out air and moisture, slowing down heat transfer, and can be used on hot or cold water pipes, chilled water, and refrigerant lines to prevent sweating and condensation. Service temps as low as -20º F with a high continuous temperature of 160º F and a high intermittent temperature of 220º F. 2˝ x 1/8˝ x 30´ roll 4218-W3 2˝ x 1/8˝ x 30´ roll - 4218-12 dispenser package Cork Tape Formulated and manufactured as an insulating material for preventing sweating and condensation on refrigerant lines, cold pipes, and other commercial refrigeration and A/C systems. Serves as an excellent insulator on hot pipes, and can also be used as a gasketing material, a sound-deadening material, and for wrapping valves, tees, and fittings. Service at temps as low as -30ºF, as high as 200ºF and won’t sag up to 350ºF. 2˝ x 1/8˝ x 30´ roll 4217-W3 Foam-Tite® Cork-Tite® An economically priced tape formulated from quality thermal insulation material. Closed cell construction and can be used on cold water pipes, chilled water lines and refrigerant lines to prevent sweating and condensation. It can also be used on hot water lines, for better insulation against heat loss. Service temperatures of -15ºF to 160ºF. Designed to insulate cold pipes for all kinds of air conditioners in cars, homes, freezers, and refrigerators. Helps stop condensation problems and is ideal for blocking heat gain in cold pipes and preventing heat loss in hot pipes. An effective sound dampening material, it can also be used for gasketing purposes, sticks to dry metals and seals tightly without drying. Flexible and does not shrink or melt within the service temperatures of -20 ºF to +200 ºF. 2˝ x 1/8˝ x 30´ roll 4219-12 2˝ x 1/8˝ x 30´ roll 4217-12 Foam Tape PE Thumb-Tite® Insulation tape providing an economical way to prevent sweating or condensation on air conditioning, refrigeration, chilled water or other cold lines. Also used on hot water lines for insulation against heat loss, and it can be overlapped or the edges can be pressed together. Formulated and manufactured for use in many sealing, insulating, and general maintenance applications. Excellent adhesion capability and is non-staining, non-hardening, and unaffected by wide variations in temperature — an excellent thumbing grade. Each box contains two 1-pound bars. 2˝ x 1/8˝ x 30´ roll 4219-20 2 lb. box 4216-92 Nu-Foam® Sealing and Caulking Cords An expanding polyurethane prepolymer foam used as a sealant and insulating product on openings created for refrigeration, air conditioning and heating tubes or pipes, duct joints, and other areas where unwanted air penetration might occur. Contains no CFCs or any HCFCs and is UL classified and fire retardant. Nonstaining sealers formulated to be waterresistant, dust- resistant and white in color. They securely adhere to most surfaces and provide excellent insulation value. They are available in 3/8˝ pre-shaped extruded cords, with serrated release paper. 12 ounce can 20 ounce can 3/8˝ x 25´ roll 4216-27 4293-04 4293-75 Visit us at www.nucalgon.com or call 1-800-554-5499 23 Insulation Products Insulation Products Glycol Propylene Glycol Freez-Kontr’l® An expanded family of heat transfer fluids (anti-freeze) based upon non-toxic propylene glycol. All products are fully formulated to provide optimum freeze protection as well as corrosion protection in chilled water, hydronic and other closed systems. Safe to use where contact with potable water is possible. GRAS certified. • Freez-Kontr’l — provides greater than -60 ºF freeze protection and greater than -100 ºF burst protection. • Freez-Kontr’l 95/5 — a fully concentrated (~100%), inhibited propylene glycol product. • Freez-Kontr’l 35 — formulated with 35% propylene glycol for use as a secondary coolant in supermarket rack applications. • Freez-Kontr’l FG — a certified USP, food grade propylene glycol product at ~100% concentration. Inhibited. NSF registered. Freez-Kontr’l Freez-Kontr’l 95/5 Freez-Kontr’l 35 Freez-Kontr’l FG 1 gallon bottle 5 gallon pail 55 gallon drum 5 gallon pail 55 gallon drum 55 gallon drum 55 gallon drum 4188-07 4188-05 4188-02 4188-06 4188-03 4188-35 4188-04 Burst-Kontr’l® AP-100 A specially formulated propylene glycol heat transfer solution for use in boilers having aluminum heat exchangers. It has corrosion inhibitors to protect aluminum, copper, solder, brass, and steel. Provides burst protection to -100 º F and freeze protection to -60 º F. 5 gallon pail 4187-15 Ethylene Glycol Freez-Therm® An inhibited heat transfer fluid and anti-freeze based upon ethylene glycol. It can be used in chilled water, hydronic, and other closed systems for both freeze point suppression and corrosion inhibition. An uninhibited version is also available in drums on special order. 1 gallon bottle 5 gallon pail 55 gallon drum 4189-07 4189-05 4189-01 Glycol Equipment Glycol Refractometer An accurate and economical tool for ensuring proper levels of glycol treatment in HVAC fluid systems. Removes guess work and prevents wasteful over-treatment. It has metal body with cushioned eyepiece, focus adjustment, and a rubber hand grip. A calibration screwdriver, calibration fluid, a plastic pipette, optical cleaning cloth, and a rugged carrying case are included. 1 each Nu-Calgon Number 61301 ClenAir Number GLY32 Glycol/Oil Transfer Pump Heavy-duty pump designed to transfer Freez-Kontr’l®, Freez-Therm®, or oil products (up to 1000 sus) from Nu-Calgon supplied 55 gallon drums to their application. 1 each 24 4817-0 Winter Treat® Multi-treatment product for hot water and steam heating boilers and other closed water systems. It emulsifies and cleans away rust and corrosion deposit sludge, as well as inhibits system corrosion, foaming, surging, and lime scale. Typical use is one quart per 25 gallons of water. 1 quart bottle 1 gallon bottle 4390-32 4390-08 Ty-lon® B20 A liquid nitrite-borax corrosion inhibitor and dispersant for closed recirculating systems. It combines corrosion inhibitors, a unique copolymer dispersant, and a color indicator to facilitate leak detection, into a complete treatment for hot and chilled water closed systems containing ferrous and non-ferrous metal components. 5 gallon pail 7537-05 Ty-lon® B14A An all-in-one boiler treatment product that controls scale, corrosion, and condensate line corrosion in low pressure, low make-up steam heating boilers where 90% or more of the condensate is returned. It is chromate-free and contains a color indicator for visual determination of treatment residual. Its balanced formulation provides an energy-efficient way of heating. 5 gallon pail 7519-05 System Cleaner A liquid, heavy-duty industrial alkaline cleaner specifically formulated to emulsify and clean equipment surfaces and pipe fouled by cutting oils, grease, lubricants, corrosion products, and other debris. 5 gallon pail 4370-08 Water Test Kits Bacteria Test Kit Bromine/Chlorine Test Kit Kit contains 10 agar paddle tests that are used to monitor bacterial contamination in cooling tower and evaporative condenser water. Test can be performed in a lab or on site. Each side of the paddle is coated with TTC Agar, material that supports growth of most common bacteria. Regular testing will detect and show when bacteria counts are rising. 1 each 4802-0 Kit measures free and combined halogen (chlorine, bromine), and it should be used to support treatment with Bromicide Tablets. Residual can be expressed as 0.2 ppm or 0.5 ppm of free halogens. Dropper technique is used. Complete Test Kit Nitrite Test Kit The complete test kit for cooling water and boiler water application testing. In addition to pH, this kit also provides tests for obtaining alkalinity, nitrite, hardness, sulfite, and chloride levels. Used for testing treatment residual of Ty-Ion B20 and Ty-Ion B14A. It is a cerric ammonium nitrate (can) titration method, and it can be used in systems containing glycol. Each drop equals 40 ppm of nitrite. 1 each W017-0 1 each 1 each 4803-0 4797-0 No. 89A Test Kit Organic Phosphonate Test Kit No. 89A Test Kit contains tests for determining hardness, pH, chloride and alkalinity, as well as treatment residual tests for Ty-Ion C70, Cal-Treat 233, No. 340 Liquid Scale Inhibitor, and Ty-Ion B20. Used to determine the treatment residual of No. 340 Liquid Scale Inhibitor, Ty-Ion C70, and Cal-Treat 233. 1 each 1 each 4804-0 4798-2 Visit us at www.nucalgon.com or call 1-800-554-5499 25 Closed Systems & Steam Boilers Closed Systems & Steam Boilers Water Treatment Scale Removal Neutralized Working Strength pH Color Indicator Nu-Calgon’s exclusive “built-in” pH color indicator tells you when to add more acid, and it lets you see when the system is clean. At working strength, the acid cleaning solution is green or light blue. When the acid solution is neutralized and is no longer working, the solution turns purple and more acid must then be added. The system is clean when the green color is retained for 20-45 minutes. Competitive Product with Dangerous Foam Nu-Calgon Low-Foaming Liquid Scale Dissolver Low-Foaming Performance To demonstrate its greater low-foam property, Liquid Scale Dissolver was added to a beaker containing lime scale. A leading competitive liquid product was added to another beaker containing an equal amount of lime scale. See the difference! When cleaning towers and evaporator condensers, low-foam is the preferred approach as high foam is dangerous to both personnel and surroundings. Liquid Scale Dissolver A hydrochloric (muriatic) acid formulated to remove calcium scales from cooling towers and other water-cooled equipment. It contains low-foaming corrosion inhibitors and a built-in pH color indicator to let you know when the acid has been neutralized. pH test paper is also included. USDA approved. 1 gallon bottle 5 gallon pail 55 gallon drum 4330-08 4330-05 4330-01 Eco-Lyme® Eco-Lyme is a new chemistry for the HVACR market that provides a unique blend of performance with a desired eco-profile. The product is specially formulated to achieve descaling behavior of competing hydrochloric acid-based chemistry descalers. However, the active ingredient is substantially safer on equipment metals. Eco-Lyme is ideal for stainless steel construction to eliminate potential issues of localized corrosion/pitting caused by repeated use of hydrochloric acid. Eco-Lyme is odorless, making it safer to use in the field. NSF registered. 1 gallon bottle 5 gallon pail 55 gallon drum 4167-08 4167-05 4167-01 Season Start® “Imperial Grade” Scale Remover A powdered sulfamic acid formulation that contains the best inhibitors available for protecting all metals, including galvanized metal. It is the best and the safest dry acid cleaner available. It contains a built-in pH color indicator to let you know when the acid solution has been neutralized as well as wetting and anti-foaming agents. USDA approved. 10 lb. container 50 lb. pail 4360-88 4360-84 Initial Dosage Recommendation 26 Tons of Horsepower Liquid Scale Dissolver Eco-Lyme Season Start 10 2 gallons 4 gallons 10 lbs. 30 5 gallons 10 gallons 30 lbs. 50 10 gallons 20 gallons 50 lbs. 90 15 gallons 30 gallons 75 lbs. Vital-Flo® Tankless Water Heater Descaler Kit The Vital-Flo Tankless Water Heater Descaler Kit is a complete service tool for descaling tankless water heaters. It consists of a submersible descaler pump, a set of 5-foot long hoses with 3/4˝ female hose threaded assemblies, formulated descaler solution packaged in a lidded 4 gallon chemical resistant container. The solution is also available separately. NSF registered. Vital-Flo kit Vital-Flo descaler solution 4387-01 4387-02 Feeding Equipment No. 31-TX1 Acid Pump Compact submersible pump designed for circulating strong acids and cleaning solutions. All parts are constructed of acid-resistant materials. 1 each 4603-0 HK-31 Hose Kit An accessory item available for use with the No. 31-TX Acid Pump. Kit includes two 1/2 inch tubing adapters, two 10 foot sections of 1/2 inch clear plastic tubing and three hose clamps. 1 each 4604-0 Scale Prevention Season Treat (6R Micromet®) This patented Micromet® Plate product is contained in a unique flow-through package. The package design makes it simple to treat small cooling towers and evaporative condensers. Simply unwrap the package and place it in the sump. One canister treats up to 10 tons for scale (5 tons for corrosion) for five to six months. 1 canister 4364-88 Ty-Ion® C70 An all-organic liquid scale, deposit, and corrosion inhibitor for use in open recirculating cooling water systems, evaporative condensers, and air washer systems. This treatment program is particularly effective in preventing scale deposits in systems that utilize make-up water with high scaling potentials. 5 gallon pail 15 gallon pail 55 gallon drum 7597-05 7597-P3 7597-01 No. 340 Liquid Scale Inhibitor An extremely concentrated scale inhibitor that is effective in hard, highly alkaline water. It is very stable and does not form any sludge. It is most effective at treatment levels between 10 and 15 parts per million. A constant, accurate feed is accomplished with a Drip Feeder or CMS Feed Pump. USDA approved. 1 gallon bottle 5 gallon pail 55 gallon drum 4340-08 4340-05 4340-01 To Inhibit Scale Formation Tons of Refrigeration or Horsepower Containers of Season Treat Ty-lon C70 Required per Month No. 340 Liquid Scale Inhibitor Required per Month Bleed-off for Most Scale-forming Waters 10 1 1/4 gallon 1/4 gallon 1/8 gpm 30 3 2/3 gallon 1/2 gallon 1/3 gpm 50 5 1 gallon 3/4 gallon 1/2 gpm 100 --- 2 gallons 1 1/2 gallons 1 gpm 120 --- 2 1/2 gallons 2 gallons 1 1/4 gpm 150 --- 3 gallons 2 1/2 gallons 1 1/2 gpm Visit us at www.nucalgon.com or call 1-800-554-5499 27 Water Treatment Water Heater Scale Removal Water Treatment Corrosion Prevention Cal-Treat® No. 233 A liquid formulation that is used for controlling severe corrosion in evaporative condensers and cooling tower systems. It is based upon a synergistic formulation of zinc, molybdate, and organic phosphonate. Provides superior corrosion control and inhibits scale accumulation. 5 gallon pail 4149-05 To Control Corrosion Cal-Treat No. 233 Required per Month Bleed-off for Most Corrosive Waters Capacity of System in Tons of Horsepower 1/3 gallon 1/10 gpm 10 1 gallon 1/4 gpm 30 2 gallons 3/8 gpm 50 3 gallons 1/2 gpm 90 Algae Prevention No. 85 Algaecide No. 85 Algaecide is a polymeric, cationic biocide that has been developed for controlling biological growth in equipment. It is an EPA registered product to kill algae, bacteria, and fungi in recirculating water systems, industrial air washing systems, and closed systems. 1 gallon bottle 4108-08 Bromicide Tablets A chlorine-bromine donating organic compound in tablet form. It slowly releases powerful oxidizing hypohalous acids, which prevent algae and slime bacteria fouling in open recirculating cooling water systems and evaporative coolers. It also has the capability of breaking up and removing existing biological mass from system surfaces. USDA approved and EPA registered. 50 lb. pail 4109-M9 To Kill Algae or Slime Growth Tons of Refrigeration or Horsepower Gallons of No. 85 Algaecide per Month Number of No. 90 Bromicide Tablets for an Average System 10 1/6 gallon 5 30 1/3 gallon 15 50 1/2 gallon 25 90 2/3 gallon 45 Other Water Treatment Products Humidi-Pro™ Humidi-Pro is designed for humidifiers using up to 25 gallons per day and will inhibit scale for one season. Install Humidi-Pro on the water line that supplies water directly to the humidifier. 1 each 4190-02 pH-Treat™ pH-Treat is an in-line treatment product specifically for the treatment of the acidic nature of the condensate water produced by today’s high efficiency furnaces. Includes fitting kit for easy installation. 1 each 28 4720-06 Evap-Treat® Used in evaporative coolers or “swamp coolers” to prevent scale and corrosion. Place it in the cooler sump and it will last all season long, thereby increasing pad life. Utilizes 6R Micromet®, a slow dissolving polyphosphate. 1 each (coolers up to 6,500 cfm) 1 each (coolers up to 10,000 cfm) 4173-04 4173-06 Water Sample Bottles The proper way to treat a cooling tower, closed loop system, or ice machine is to have the supply or makeup water tested. Nu-Calgon provides this valuable service for free and will analyze the water and recommend effective treatment. These bottles can also be used to send in glycol samples to test freeze points. 1 each (3 bottles) 4995-0 No. 215 and No. 1075 Drip Feeders Used for feeding No. 340 Liquid Scale Inhibitor, Cal-Treat 233, Ty-Ion C70 and No. 85 Algaecide. Calibrated at the factory to ensure accurate feeding. Provides the benefits of continuous treatment for small systems without the high cost usually associated with automatic feeding equipment. No. 215 Drip Feeder No. 1075 Drip Feeder 4669-W3 4670-W3 Jug Holders These should be used when drip feeding any of Nu-Calgon’s liquid water treatment products. Once secured to the cooling tower or evaporative condenser, they will hold the 1 or 5 gallon containers in the proper position. 1 gallon holder 5 gallon holder 4606-0 4607-0 CMS III and CMS-IV Cooling Tower Monitor System For monitoring conditions in cooling towers and evaporative condensers. Provides subsequent bleed-off and chemical feed. It features a combination monitor and pump engineered into one-piece digital equipment. Complete system includes a solenoid valve. CMS III CMS IV 4608-0 4608-4 No. 20L and No. 100L Feeders Steel tanks suitable for pressures up to 150 psi and temperatures up to 212º F. Uses 3/4 inch FNPT connections for installing on bypass to any size line. Use No. 20L Feeder for initial charges up to 20 pounds (or 2 gallons). Use No. 100L Feeder for initial charges up to 100 pounds (or 10 gallons). Inlet/outlet strainers not included. No. 20L Feeder No. 100L Feeder 4628-0 4650-0 Conductivity Meter A handheld conductivity meter with built-in cell and automatic temperature compensation. It has an easy-to-read digital meter (in micromhos, 0-10,000) and dual point calibrations. 1 each 4812-0 Visit us at www.nucalgon.com or call 1-800-554-5499 29 Water Treatment Other Water Treatment Products Plumbing Products Plumbing Products Drain Solve Ideal for condensate pan drains. Drain Solve saves time and money with its ease of use. It eliminates application concerns associated with more reactive, fuming drain openers. Simply pour it down the drain and let it work without fear of noxious fumes or reactions. Does not contain sulfuric acid. 1 quart 1 gallon 4165-24 4165-08 Calci-Solve Remove scale from lines and clear clogged drains easily and effectively with Calci-Solve. The product includes a special inhibitor that coats the inside of the pipes with a protective film, allowing the acid in Calci-Solve to quickly dissolve calcium, magnesium, sodium, lime, rust, and other elements without harming pipes. 1 quart 1 gallon 4134-24 4134-08 UrinaKleen Keep urinals free flowing with UrinaKleen. Use it to dissolve urinary salts, mineral scale, and rust deposits which are found in urinals. It also attacks the primary source of odors. 1 quart 1 gallon 4590-24 4590-08 A/C Drain Sucker® A/C condensate drain pan overflow is caused by slime and sludge that builds up and clogs the drain line. The A/C Drain Sucker quickly removes the clog and the excess water, resolving the overflow problem. The kit includes a PurCool® Pan Strip to provide months of preventive treatment and free flowing drains, as well as all fittings and hoses for suction or pressure applications. A/C Drain Sucker kit PurCool Pan Strip - treats 3 tons - 6 mos. Nu-Calgon Number 61308 61043 ClenAir Number CADS1 1903D Vital-Flo® Tankless Water Heater Descaler Kit The Vital-Flo Tankless Water Heater Descaler Kit is a complete service tool for descaling tankless water heaters. It consists of a submersible descaler pump, a set of 5-foot long hoses with 3/4˝ female hose threaded assemblies, and a formulated descaler solution packaged in a lidded four gallon chemical resistant container. The solution is also available separately. NSF registered. Vital-Flo kit Vital-Flo descaler solution 30 4387-01 4387-02 Nickel-Safe Ice Machine Cleaner The original Nickel-Safe Ice Machine Cleaner. It is a food-grade citric-phosphoric acid product for removing scale deposits from ice machines having nickel-plated or tinplated evaporators, and it is acceptable for use in all ice machines containing nickel. It mixes to form a green solution, which makes rinsing easier. USDA approved. 16 fluid ounce bottle 1 gallon bottle 4287-34 4287-08 Liquid Ice Machine Cleaner Liquid Ice Machine Cleaner is a food-grade phosphoric acid that is fast acting, yet safe to use. It has been formulated to remove scale deposits from ice machines and coffee urns. It does not give off any harsh fumes or contain chlorine or chlorides that would attack stainless steel. USDA approved. NSF registered. 8 fluid ounce bottle 1 gallon bottle 4207-47 4207-08 IMS-III Sanitizing Concentrate IMS-III is an EPA registered sanitizing concentrate formulated to sanitize hard, non-porous surfaces and to eliminate odors and slime growths. No rinsing is required when diluted to 1.6 ounces per gallon. Formulated for general use in ice machines, ice cream dispensing equipment, and other food processing equipment. 16 fluid ounce bottle 4211-34 Ice Guard™ Plus Ice Guard Plus contains advanced technology to prevent and control slime and other microbial growths in ice machines. The technology utilizes known antimicrobial properties to inhibit microorganism reproduction that cause slime typically found in ice machines. One unit provides up to 6 months protection in machines producing up to 1200 lbs. of ice per day. 1 each 4209-07 6Rsp Micromet® A slow dissolving phosphate specifically formulated for inhibiting scale in ice machines and other equipment using low volumes of water. It is used in Nu-Calgon scale controlling cartridges and requires replacement once every six months. Typical dosage is 8 ounces per 500 pounds of ice (50 gallons of water) a day. 50 lb. pail 4265-50 Visit us at www.nucalgon.com or call 1-800-554-5499 31 Water Filtration - Maintenance Water Filtration - Maintenance Water Filtration Water Filtration - OEM Replacements CFS Filtration System A family of replacement cartridges and manifolds designed to service existing CUNO® CFS installations. A cost-effective water filtration system for food service applications: ice machines, fountain beverages, steam ovens, and drinking water. These systems offer manifold and sanitary quick-change cartridges to fit the existing CUNO CFS brand installations and can also support new filtration installations. Nu-Plus CFS is the reliable choice for water filtration to prevent unwanted troubles caused by sediment, scale, or taste and odor existing in CUNO installations. Sediment – 5 micron Sediment – 5 micron / phosphate Carbon Block - .5 micron Carbon Block - .5 micron / phosphate Single Head Twin Head Triple Head Twin Series 4623-10 4623-11 4623-12 4623-13 4623-01 4623-02 4623-03 4623-06 The CTL Series The CTL Series contains a matching product for the Tri-Liminator Filtration System with specifications that are nearly identical. For example, the CTL’s primary cartridge (C0070) will replace both the K00070 and K00174 cartridges, and it has more scale control ability than either of the Tri-Liminator cartridges. Part numbers are easily crossed over: CTL10 replaces the Tri-L10. CTL 220 Prefilter Primary cartridge - CG5-20S 4610-30 4621-43 9108-27 Water Filtration Micro-Plus® & Micro-Carbon 4 The complete all-in-one treatment for ice machines, coffee urns and brewers, humidifiers, steamers, etc. The Micro-Plus “in-line” filters contain 6R Micromet® to control scale, high-grade activated carbon for eliminating objectionable tastes and odors, and filter discs to remove silt and sediment down to 20 microns. Available in four sizes with 1/4˝ FPT connections. When properly sized, each filter will last up to six months. The Micro-Carbon 4 is available for removing objectionable tastes and odors. Micro-Plus 2 Micro-Plus 4 Micro-Plus 8 Micro-Plus 16 Micro-Carbon 4 4615-W3 4612-W3 4613-Y8 4614-Y8 4617-24 Application Micro-Plus 2 Micro-Plus 4 Micro-Plus 8 Micro-Plus 16 Micro-Carbon 4 Water (per day) 12.5 gallons 25 gallons 50 gallons 100 gallons 50 gallons Up to 125 lbs. Up to 250 lbs. Up to 500 lbs. Up to 1000 lbs. --- 25 lbs.(1,250 cups) 50 lbs. (2,500 cups) 100 lbs. (5,000 cups) 200 lbs. (10,000 cups) --- Ice (per day) Coffee (per week) 32 NP Series Housings These housings are designed to hold one of the NP Cartridges used to filter water for ice machines, coffee urns, and other beverage equipment. The NP24DD and NP48DD Housings fit specific NP24 or NP48 cartridges for controlling scale, sediment, or objectionable tastes and odors. The NP24DD is equipped with 3/8˝ FPT connections and handles up to 4.0 gpm. The NP48DD is equipped with 1/2˝ FPT connections and can handle flow rates up to 5.0 gpm. NP24DD NP48DD 4704-24 4714-24 6R Micromet®/Carbon Cartridge A custom cartridge, combining 6R Micromet for scale-control and a carbon block for sediment (10 microns), taste and odor control. NP24PC NP48PC 4706-87 4716-87 Carbon Block Cartridge The NP24C Cartridge fits the NP24DD Housing while the NP48C fits the NP48DD. These carbon blocks will remove most objectionable tastes and odors and are rated to remove particulate to 10 microns. NP24C NP48C 4701-87 4711-87 Sediment Cartridge The NP24S (5˝) and the NP48S (10˝) are made from FDA-approved polypropylene construction and filter to 5 microns. In addition, the 10˝ and 20˝ versions are available in bulk packaging. NP24S NP48S 20˝ bulk 4702-87 4712-87 4621-43 6R Micromet® Cartridge The NP246R Micromet Cartridge contains 1 pound of 6R Micromet, and it fits the NP24DD Housing. The NP486R Cartridge contains 2 pounds of 6R and fits the NP48DD Housing, with 10 micron filtration. NP246R NP486R 4705-87 4715-87 6R Micromet®/Sediment Cartridge Another custom cartridge within the NP Series, consisting of polypropylene for filtration (5 microns) and phosphate for scale-control. NP48PS 4717-87 NP Series Brackets Some installations may require two or three NP Series housings to meet more than one specific water-related condition. This custom installation can be accomplished through the use of one of the NP Series multi-housing brackets. Two housing brackets Three housing brackets NP2BR NP3BR Problem to Solve Cartridge Type Sediment “S” Cartridges 4 “C” Cartridges 4 “6R” Cartridges 4 “PC” Cartridges 4 “PS” Cartridges 4 Daily Capacities Taste & Odor Scale “48’s” 1800 lbs. (200 gal.) 3600 lbs. (400 gal.) 1800 lbs. (200 gal.) 3600 lbs. (400 gal.) 4 900 lbs. (100 gal.) 1800 lbs. (200 gal.) 4 600 lbs. (65 gal.) 1200 lbs. (135 gal.) 4 4 “24’s” 4 Visit us at www.nucalgon.com or call 1-800-554-5499 550 lbs. (60 gal.) 33 Water Filtration -NP Series Water Filtration - NP Series Water Filtration - Nu-Plus® by Everpure® Heads QL3B Single System Head Used with any Nu-Plus® E Series filters. Head includes a water shut-off valve with mounting bracket and screws. (3/8˝ NPT) 1 each 4621-07 QC7I Single Head Ideal for all Nu-Plus® E Series filters. Head includes a shut off, flushing valve, and outlet pressure gauge on a box bracket design. (3/8˝ NPT) 1 each 4621-01 QC7I Twin Parallel Head Dual filter head that is parallel plumbed for two Nu-Plus® E Series filters, either mix or match. Head includes a shut off, flushing valve, and outlet pressure gauge on a box bracket design. (3/4˝ NPT) 1 each 4621-02 QC7I Triple Parallel Head Triple filter head parallel plumbed for three Nu-Plus® E Series filters. Head includes a shut off, flushing valve, and outlet pressure gauge on a box bracket design. (3/4˝ NPT) 1 each 4621-03 QC7I Quad Parallel Head Quad filter head parallel plumbed for four Nu-Plus® E Series filters. Head includes a shut off, flushing valve, and outlet pressure gauge on a box bracket design. (3/4˝ NPT) 1 each 4621-04 *Everpure® is a trademark of Everpure, Inc., Westmont, IL. 34 MRS-20 Reverse Osmosis System Complete mineral reduction water processing system that removes at least 90%+ of all dissolved solids that cause scale build-up. The MRS-20 system removes taste and odor causing contaminants as well as dirt and particles. The two-part design makes installation flexible. It has no moving parts and requires no electrical power. System includes mineral reduction processor, carbon filter cartridge, reverse osmosis cartridge, and storage tank. No monitoring of grains per gallon is necessary. MRS-20 9797-91 Kleensteam CT and Kleensteam II Everpure’s second generation water treatment system for steam applications. Kleensteam is a total system delivering high quality filtered water with scale inhibition as well as deliming capabilities. The dual cartridge design provides enhanced performance for low and high flow capacity steamers and flexibility for expanding to meet future needs. Kleensteam also reduces chlorine-induced corrosion. It’s simple to install, operate, and maintain. Kleensteam CT Kleensteam II 1.67 gpm max. flow 2.5 gpm max. flow 9797-50 9797-21 Nu-Plus E Series by Everpure High Flow CSR Manifold with Prefilter Utilizing the nu-MC2 or the nu-XC2 cartridges, this system provides premium quality water to high flow fountain dispensers, coffee makers and ice machines. New and improved MicroPure II media inhibits the growth of bacteria. High Flow CSR reduces chlorine taste and odor and other offensive contaminants that can adversely effect the taste of beverages. Precoat submicron technology reduces dirt and particles as small as 1/2 micron and reduces health contaminants such as cysts. Additionally, the SRX Housing inhibits scale when it is equipped with scale-inhibiting IMF-10 ScaleSticks®. 10˝ 20˝ High Flow CSR Manifold with Prefilter Twin Triple 9294-02 9294-03 9294-22 9294-23 Quad 9294-04 9294-24 Nu-Plus E Series by Everpure Coldrink/Insurice Systems The Coldrink/Insurice manifolds can be used with any Nu-Plus by Everpure cartridges. i.e. the MC2 or XC2 for carbonated beverages or i20002 or i40002 for ice machines. Utilizes the systems' existing 10" or 20" pre-filter on a single, twin, triple, or quad manifold. Systems come with the initial EC110 or EC210 pre-filter cartidge. Just purchase the appropriate Nu-Plus by Everpure cartridge for your application. 10˝ 20˝ Coldrink/Insurice Manifold with Prefilter Single Twin Triple 9293-01 9293-02 9293-03 9293-21 9293-22 9293-23 Visit us at www.nucalgon.com or call 1-800-554-5499 Quad 9293-04 9293-24 35 Water Filtration - Nu-Plus® by Everpure® Systems Water Filtration - Nu-Plus® by Everpure® Cartridges nu-i20002 and nu-i40002 Reduces water-related ice machine problems caused by dirt, objectionable tastes and odor and scale build-up. Pre-coat submicron filtration reduces particles as small as 1/2 micron along with chlorine and other offensive contaminants. In addition, both cartridges use 6R Micromet®, a highly acclaimed scale inhibitor that inhibits scale build-up caused by dissolved minerals. NSF registered under NSF/ANSI Standards 42 and 53. • • • • Pre-coat filtration with Micro-Pure® II antibacterial protection Premier 6R Micromet scale control Cyst and asbestos fibers reduction Sanitary quick-change cartridge replacement nu-i20002 4621-10 Capacity: 9,000 gallons • 750 lbs. for most cubers • 1,500 lbs. for most flakers nu-i40002 4621-11 Capacity: 12,000 gallons • 1,000 lbs. for most cubers • 2,000 lbs. for most flakers nu-MC2 and nu-XC2 Reduces chlorine taste, odor and other offensive contaminants that can adversely affect the taste of fountain beverages. Pre-coat submicron filtration reduces particles as small as 1/2 micron, and it helps retain carbonation in drinks. NSF registered under NSF/ANSI Standards 42 and 53. • • • • Pre-coat filtration with Micro-Pure® II antibacterial protection Reduces objectionable tastes and odors Cyst and asbestos fibers reduction Sanitary quick-change cartridge replacement nu-MC2 Capacity: 9,000 gallons 4621-20 nu-XC2 Capacity: 12,000 gallons 4621-21 BH2 and OCS2 Cartridge • • • • • • Delivers premium quality water for ice and coffee applications Designed for applications where the i20002 is too long Precoat submicron particulate reduction Inhibits scale formation Taste and odor reduction NSF registered under NSF/ANSI standards 42 and 53. BH2 4621-12 Capacity: 3,000 gallons or 6,000 pots of coffee • 0.5 gpm max. flow OCS2 9618-07 Capacity: 1,500 gallons or 3,000 pots of coffee • 0.5 gpm max. flow OW200L and OW4Plus Cartridge • • • • • • Ideal for office or residential water systems Unique filter blend uses activated carbon to reduce chlorine taste, odor, and other offensive contaminants Reduces lead to below the Federal Action Level of 10 ppb Precoat submicron technology reduces dirt and particles as small as 1/2 micron Inhibits scale build-up in water-using appliances NSF registered under NSF/ANSI standards 42 and 53 OW200L Capacity: 480 gallons 9619-06 OW4PLUS Capacity: 2,000 gallons 9635-06 *Everpure® is a trademark of Everpure, Inc., Westmont, IL. 36 4CB5, 7CB5, 4CB5-S, and nu-7CB5-S Cartridge Carbon Block filter finely polishes water for high quality beverages and food applications. NSF registered under NSF Standard 42. • Problem-solving cartridge for high particulate or low flow water pressure areas • Taste and odor, chlorine reduction • Particulate reduction to 5 micron • 4CB5-S, and nu-7CB5-S cartridges control scale 4CB5 Capacity: 6,000 gallons 4621-32 7CB5 Capacity: 10,000 gallons 9618-16 4CB5-S Capacity: 6,000 gallons 4621-31 nu-7CB5-S Capacity: 10,000 gallons 4621-30 4FC5, 7FC5, 4FC5-S, and 7FC5-S Cartridge New Fiberdyne™ II media with Agion® antimicrobial protection to inhibit potential bacterial growth. Balanced for optimum performance in varying water qualities. Helps retain the drink’s carbonation. • Increased capacity 25,000 gallons • 2.5 gpm flow rate • Taste and odor reduction • 5 micron rating • Particulate reduction • Scale inhibition (4FC5-S and 7FC5-S) • NSF standards 42 and 53 4FC5 Capacity: 15,000 gallons 9693-21 7FC5 Capacity: 25,000 gallons 9693-61 4FC5-S Capacity: 15,000 gallons 9693-31 7FC5-S Capacity: 25,000 gallons 9693-71 4FC, 7FC, 4FC-S, and 7FC-S Cartridge New Fiberdyne™ II media with Agion® antimicrobial protection to inhibit potential bacterial growth. Balanced for optimum performance in varying water qualities. Improves the taste of fountain drinks and helps retain the drink’s carbonation. • Taste and odor reduction • 0.5 micron rating • Particulate reduction • NSF standards 42 and 53 • 2.5 gpm flow rate • Scale inhibition (4FC-S, and 7FC-S only) 4FC Capacity: 15,000 gallons 7FC Capacity: 25,000 gallons 9692-21 4FC-S Capacity: 15,000 gallons 7FC-S Capacity: 25,000 gallons 9692-31 9692-61 9692-71 Visit us at www.nucalgon.com or call 1-800-554-5499 37 Water Filtration - Nu-Plus® by Everpure® Cartridges Water Filtration - Nu-Plus® by Everpure® Cartridges 4SI and 7SI Cartridge Specially designed for ice machines. This cartridge does not include carbon, which allows for complicance with ASHRAE Standard 188. The cartridge reduces sediment and particulate down to 1/2 micron and reduces cyst and Giardia. The filter allows chlorine to pass through, which helps reduce slime and bacteria growth inside the ice machine and ice bin. Ideal for food service operations where baking of bread and pastries is done on-site. • Scale inhibition • 0.5 micron rating • Particulate reduction • NSF standards 42 • Cyst reduction 4SI Capacity: 15,000 gallons • 2.0 gpm flow rate 7SI Capacity: 25,000 gallons • 3.5 gpm flow rate 9606-51 9606-01 7CLM Cartridge Reduces chloramines, chlorine taste and odor and other offensive contaminants that can adversely affect the taste of beverages. The cartridge reduces particles down to 1/2 micron and reduces cysts and Giardia. Improves the taste of fountain beverages and helps retain the drink’s carbonation. NSF registered. • Chloramine reduction • Cyst reduction • Chlorine reduction • Particulate reduction 7CLM 9693-01 Capacity: 3,600 gallons at 1.7 gpm, 5,500 gallons at 1.33 gpm 7SO Softening Cartridge A softening cartridge that reduces scale-forming minerals like calcium and magnesium in hard water situations. It may be used on water having up to 30 grains hardness per gallon, at flow rates of up to 1/2 gallons per minute. It is a sanitary quick change cartridge that makes replacement easy. It should be used with an Everpure fine filter cartridge installed in a series plumbed twin head. 7SO Capacity: 2,000 grains • 0.5 gpm max. flow 9607-04 Replacement Cartridges for CUNO® Nu-Plus® CU and Nu-Plus CU-S The Nu-Plus E Series CU and CU-S cartridges are replacements that are compatible with the CUNO Series CFS 8000 filter cartridges. Both incorporate a carbon block filter that reduces objectionable tastes and odors as well as chlorine and other contaminates, providing high quality beverage and ice. They also reduce extra fine dirt as small as 5 microns. Additionally, the CU-S provides for the reduction of scale formation. Nu-Plus CU 4622-20 Capacity: 10,000 gallons (37,850 liters) • 1.5 gpm flow Replaces CFS-8112, CFS-8720 & CFS-8812 Nu-Plus CU-S 4622-10 Capacity: 10,000 gallons (37,850 liters) • 1.5 gpm flow Replaces CFS-8112S,CFS-8720S & CFS-8812S *Everpure® is a trademark of Everpure, Inc., Westmont, IL. *CUNO® is a trademark of 3M. This product is not manufactured, sponsored, or affiliated with 3M. 38 Nu-Plus® 10˝ and 20˝ Coarse Prefilters A 10˝ and 20˝ clear housing, each including a 10˝ and 20˝ replaceable prefilter cartridge. Filters out larger dirt and rust particles, thereby extending the life of submicron and carbon block filters. E-10 E-20 4621-42 4621-44 Optional: Wing Bracket for all multiple filter head systems manufactured after 2003: 4621-45 Nu-Plus® EC110 and EC210 A 10˝ and 20˝ 10-micron nominal filtration cartridge for filtering out larger dirt and rust particles, extending the life of primary filters. For use in the E-10 and E-20 housings as well as other 10˝ and 20˝ housings. EC110 (10˝) EC210 (20˝) 4621-41 4621-43 SRX Scale Inhibitor Feeder A complete system for the control of scale in ice, coffee, steam, and combination applications. It dispenses a controlled amount of HydroBlend™ compound, which provides for a more consistent feed and longer life. The system includes a clear housing and one cartridge 1 each 4621-05 Optional: Wing Bracket for all multiple filter head systems manufactured after 2003: 4621-06 Nu-Plus® IMF-7 and IMF-10 Ice Machine Feeder Scale inhibition cartridge. The translucent cartridge allows for easy visual monitoring of the product’s usage. The larger IMF-10 will last longer or treat higher volumes of water. IMF-7 IMF-10 Replacement for AR-X 7˝ Housing Replacement for SS-10 Scale Sticks 4621-13 4621-14 4JT Flushing/Sanitizing Cartridge The preferred way to introduce ScaleKleen™ Scale Remover or other sanitizing solutions (IMS-III) into all water-using equipment and vending machines. Fits into existing Everpure heads. Eliminates the need for difficult component disassembly. Easy and convenient to help you clean and maintain equipment. Approved by NAMA. 1 each 4621-00 ScaleKleen™ Scale Remover Restores equipment to peak operating efficiency by removing scale build-up. Quickly removes limescale from coffee brewers. Ideal for deliming steam and ware washing equipment. Great for office coffee system (OCS) applications. Non-toxic, safe to skin and won’t burn clothing. Sewer system disposable; can be poured down the drain. Use with 4JT Flushing/Sanitizing Cartridge. 7 ounce packets (24 per case) 2.2 lb. canister (4 per case) 39 4621-17 9798-35 Visit us at www.nucalgon.com or call 1-800-554-5499 39 Water Filtration - Nu-Plus® by Everpure® Other Filtration Products Nu-Calgon Seminars & Training Classes Free Seminars and Training Classes NATE training now online. Visit us at www.nucalgon.com. Coil Cleaning: The Clean Coil Program is a comprehensive seminar dedicated to the safe and proper procedures to clean evaporator and condenser coils. The program will help determine which cleaning method should be utilized for a particular job based on the type and condition of the unit. NATE Recognition Classes: 1 hour Continuing Education Accreditation Ice Machine Treatment and Filtration: A complete guide to “Extending the Life of an Ice Machine.” The seminar will answer the questions: why use a filter, what filter should be used, and how to keep the system clean, clear, and running properly. It also addresses all of the water-related problems associated with ice machines. (1.5 hours) Indoor Air Quality Management: The seminar covers the past, present and future of indoor air quality (IAQ). Topics covered in the session: how poor IAQ impacts a business, common causes of poor IAQ, and how to prevent poor IAQ from occurring. NATE Recognition Classes: 1 hour Continuing Education Accreditation Nu-Calgon Product Line Review: The seminar provides an overview of all the major products that Nu-Calgon offers. The presentation explores when and where to use certain products, as well as explains how using certain products can save time and money. (2 hours) Refrigeration Oils: An in-depth look at industry refrigeration oils (Mineral, Alkylbenzene, and POE) and when and where to use them. NATE Recognition Classes: 1.5 hours Continuing Education Accreditation Total System Protection: A thorough look at why burnouts occur, how to prevent them and the proper way to flush a system once a burnout occurs. The training will include acid testing and acid neutralization. NATE Recognition Classes: 1 hour Continuing Education Accreditation Water Treatment: This seminar will cover the fundamentals of water treatment for cooling towers, evaporative condensers, boilers, and chillers. NATE Recognition Classes: 1.5 hours Continuing Education Accreditation Winter Water Treatment: This program focuses on what a system needs prior to the winter season, including a review of ethylene and propylene glycol, the proper treatments for hot/cold closed systems, and low make-up steam systems. (1 hour) Energy Savings with A/C Re-New: Learn about a revolutionary product for revitalizing and energizing A/C systems. The seminar will explain how A/C Re-New will help reduce energy costs, improve cooling performance and reduce the system noise. (1 hour) Food Service Products for Ice & Beverage Filtration: A comprehensive look at the problems associated with ice and beverage filtration as well as treatment options to solve these problems. We will cover products for ice makers, coffee brewers, fountain beverage machines, steam ovens, drinking water, and more. (1 hour) 40 Serving the United States & Canada with the Finest Direct Factory Sales Force in the HVACR Industry 1. Seattle, WA 11. Kansas City, MO 21. Ocala, FL 2. Northern CA 12. St. Paul - Minneapolis 22. Tampa, FL 3. Southern CA 13. St. Louis, MO 23. Miami, FL 4. Los Angeles, CA 14. Baton Rouge, LA 24. Raleigh, NC 5. San Diego, CA 15. Milwaukee, WI 25. Richmond, VA 6. Phoenix, AZ 16. Chicago, IL 26. Baltimore, MD 7. Denver, CO 17. Indianapolis, IN 27. Philadelphia, PA 8. San Antonio, TX 18. Columbus, OH 28. NYC/New Jersey 9. Dallas - Fort Worth 19. Birmingham, AL 29. Syracuse, NY 10. Houston, TX 20. Atlanta, GA 30. Boston, MA St. Louis, MO (Hdq.) Visit us at www.nucalgon.com or call 1-800-554-5499 41 Nu-Calgon 2008 Altom Court | St. Louis, MO 63146 phone: 800-554-5499 | fax: 800-221-6302 www.nucalgon.com (416) 3-300 | Calgon is a licensed trade name.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project