Honeywell / LXE Tecton Accessories

Accessory Catalog
TECTON/MX7
Updated: March 2011
BATTERIES AND CHARGERS
MX7392BATT
Tecton Main Battery, Lithium Ion
Notes:
1) It can also be used with MX7
MX7393BATT
Tecton CS Main Battery, Lithium Ion, Low-temperature
Notes:
1) It can also be used with MX7CS
MX7394BATT
Tecton Main Battery, Lithium Ion, 10-pack
Notes:
1) It can also be used with MX7
MX7395BATT
Tecton CS Main Battery, Lithium Ion, Low-temperature, 10-pack
Notes:
1) It can also be used with MX7CS
MX7A380BATT
MX7 Main Battery, Lithium Ion
MX7A381BATT
MX7 Main Battery, Lithium Ion, Low-temperature, for use with MX7CS
Notes:
1) For use with MX7 Cold Storage.
2) Call for availability.
MX7382BATTERY
MX7 Main Battery, Lithium Ion, 10-pack
MX7383BATTERY
MX7 Main Battery, Lithium Ion, Low-temperature, for use with MX7CS, 10-pack
Notes:
1)For use with MX7 Cold Storage
2) Call for availability
MX7390CHARGER
4 Unit Main Battery Charger with power supply and US power cord.
Notes:
1) US power cord included.
MX7391CHARGER
4 Unit Main Battery Charger with power supply, C14 type power cord required.
Notes:
1) AC power cord is not included. A country specific power cord must be purchased
separately.
2) When this product is shipped internationally it may be necessary to order and ship the
appropriate internation AC power cable at the same time. This product has a C14 style AC
power connector. Choose the proper C14 style cable from the international cables in the
power cable section.
HANDLES
MX7402HANDLE
MX7504WRSTSTRAP
MX7 padded handle with rubber overmold and two finger trigger, includes wrist
strap, for use with MX7 and MX7CS. Rated down to -22 deg F (-30 deg C.)
MX7 Wrist Strap 10 Pack
BOOTS
MX7490BOOT
Black rubber protective boot. Can be used with MX7388DSKCRDL &
MX7008VMCRADLE
MX7491BOOT
Yellow rubber protective boot. Can be used with MX7388DSKCRDL &
MX7008VMCRADLE
CARRYING CASES
MX7404CASE
MX7 Voice Application case with belt
Notes:
1) MX7 with rubber protective boot will not fit in this case.
MX7408CASE
Carry case for MX7 without handle with Gearkeeper retractor
Notes:
1) MX7 with rubber protective boot will not fit in this case.
MX7411CASE
Carry case for MX7 with handle. For use with retractor MX7412BELT.
Notes:
1) MX7 with rubber protective boot will not fit in this case.
MX7412BELT
Gearkeeper retractor with belt for use with MX7411CASE.
MX7A413CASENHDL
Carry case for MX7 with no handle, includes shoulder strap
Notes:
1) MX7 with rubber protective boot will not fit in this case.
2) Large, tethered stylus can be ordered separately for this case, 9000A510STYLUS.
MX7A414CASEHDL
Carry case for MX7 with handle, includes shoulder strap
Notes:
1) MX7 with rubber protective boot will not fit in this case.
2) Large, tethered stylus can be ordered separately for this case, 9000A510STYLUS.
HOLSTERS
MX7405HOLSTER
Holster for MX7 with handle, belt not included
Notes:
1) MX7 with rubber protective boot will not fit in this holster.
2) Belt must be ordered separately.
MX7407HOLSTER
Holster for MX7 with no handle, belt not included
Notes:
1) MX7 with rubber protective boot will not fit in this holster.
2) Belt must be ordered separately.
MX7409HOLSTER
Holster for MX7 with no handle and with boot
Notes:
1) Boot and belt must be ordered separately.
2) MX7 with rubber protective boot will fit in this holster.
MX7410HOLSTER
Holster for MX7 with handle and boot
Notes:
1) Boot and belt must be ordered separately.
2) MX7 with rubber protective boot will fit in this holster.
9200L69
Adjustable nylon belt for holsters
CRADLES
MX7388DSKCRDL
Desktop cradle with spare battery charging, RS-232, USB client, and tethered
scanner support. Power supply not included.
Notes:
1) Must order power supply 9000A321PSACUS or 9000A322PSACWW separately.
2) Works with MX7 ActivSync cables list in the Interface Cables section.
3) Rated for operation bettween 32 deg F and 122 deg F (0 deg C and 50 deg C) and
spare battery charging between 50 deg F and 104 deg F (10 deg C and 40 deg C).
4) Cradle will perform “in-unit” battery trickle charging.
5) MX7 with a rubber boot will fit in the desktop cradle. The docking bay adapter cup must
be removed before the MX7 is placed in the desktop cradle.
MX7003DSKCRDL
Desktop cradle with spare battery charging, RS-232, USB client, and tethered
scanner support. Includes AC/DC power supply and US power cord.
Notes:
1) Works with MX7 ActivSync cables list in the Interface Cables section.
2) Rated for operation between 32 deg F and 122 F (0deg C and 50 deg C) and spare battery
charging between 50 deg F and 104 deg F (10 deg C and 40 deg C).
3) Cradle will perform “in-unit” battery trickle charging.
4) MX7 with a rubber boot will fit in the desktop cradle. The docking bay adapter cup must
be removed before the MX7 is placed in the desktop cradle.
MX7004DSKCRDL
Desktop cradle with spare battery charging, RS-232, USB client, and tethered
scanner support. Includes AC/DC power supply. Power cord must be ordered
separately.
Notes:
1) Works with MX7 ActivSync cables list in the Interface Cables section.
2) Rated for operation between 32 deg F and 122 F (0deg C and 50 deg C) and spare battery charging
between 50 deg F and 104 deg F (10 deg C and 40 deg C).
3) Country specific power cord must be ordered separately.
4) MX7 with a rubber boot will fit in the desktop cradle. The docking bay adapter must be removed
before the MX7 is placed in the desktop cradle.
MX7007VMCRADLE
MX7 Passive vehicle cradle. Does not support charging or communication.
U-Bracket included.
Notes:
1) RAM mount MX7A001RAMBRKT-R must be ordered separately.
2) The cradle will not work with an MX7 that has a protective boot on it.
3) The MX7 that has a protective boot on it cannot be mounted in the passive VM cradle.
MX7A001RAMBRKT-R
RAM mount kit for MX7001VMCRADLE and MX8003VMCRADLE, passive vehicle
cradle.
Attaches to U-Bracket.
MX7008VMCRADLE
MX7 Active vehicle cradle. Supports MX7 charging, USB client and powered RS-232
connector.
Notes:
1) Must order power supply and cables separately.** See below
2) Cradle will perform “in-unit” battery trickle charging.
3) Tethered serial RS-232 barcode scanning supported.
4) Rated for operation to 14 deg F and 122 deg F (-10 deg C and 50 deg C).
5) The RAM Mount kit includes arm, clamp & base. All are size “C”.
**MX7008VMCRADLE:
Note: 1) Must order power supply and cables separately.
a. For 12 Volt DC operation, use 9000A079CBL 12ML3
b. For 18-60 Volt DC input to 12V DC output use 9000301PWRSPLY
c. For 60-110 Volt DC input to 12V DC output use 9000302PWRSPLY
d. For 18-72 Volt DC input to 112V DC output use 9000304PWRSPLY
e. For 110 Volt AC input to 12V DC Output with US Power Cord use 9000A321PSACUS
f. For 110 Volt AC input to 12V DC Output without AC Power Coprd use 9000A322PSACWW
MX7A002RAMBRKT
RAM mount kit for MX7008VMCRADLE.
Notes:
1) The RAM Mount kit includes arm, clamp & base. All are size “C”.
POWER CABLES & SUPPLIES
9000301PWRSPLY
18V - 60V DC/DC power supply with cradle power cable
Notes:
1) Will work with the MX7 Active Cradle (MX7008VMCRADLE).
9000302PWRSPLY
60V - 110V DC/DC power supply with cradle power cable
Notes:
1) Will work with the MX7 Active Cradle (MX7008VMCRADLE).
900304PWRSPLY
Power adapter, 18-72V DC input to 12V DC output, includes cable.
Notes:
1) Will work with the MX7 Active Cradle (MX7008VMCRADLE).
PICTURE UNAVAILABLE
CALL FOR AVAILABILITY
9000A321PSACUS
AC/DC power supply with US power cord for use with MX7 Charge/Comm cables or
MX7 Desktop Cradle, MX7388DSKCRDL
Notes:
1) This power supply facilitates in-unit battery charging and is used in conjunction
with the RS/232 and USB Active Sync cables or can be used with the MX7388DSKCRDL.
2) US power cord included.
3) Will work with the MX7 Active Cradle (MX7008VMCRADLE).
9000A322PSACWW
AC/DC power supply, (C14 type power cord required), for use with MX7 Charge/
Comm cablesor MX7 Desktop Cradle, MX7388DSKCRDL
Notes:
1) This power supply facilitates in-unit battery charging and is used in conjunction with
the RS/232 and USB Active Sync cables or can be used with the MX7388DSKCRDL.
2) Power Cord is not included.
3) A country specific power cord must be ordered separately.
4) Will work with the MX7 Active Cradle (MX7008VMCRADLE).
9000090CABLE
AC power cable, C14 type, Schuko
9000091CABLE
AC power cable, C14 type, Denmark
9000092CABLE
AC power cable, C14 type, Italy
9000093CABLE
AC power cable, C14 type, Switzerland
9000094CABLE
AC power cable, C14 type, British
9000A079CBL12ML3
Power Adapter, Bare Wire 12 VDC
Notes:
1) Will work with the MX7 Active Cradle (MX7008VMCRADLE).
INTERFACE CABLES
MX7052CABLE
MX7 Charge/Comm Interface Cable, USB Client for ActiveSync
Notes:
1) The Charge/Comm cables facilitate Active Sync directly from the MX7 Computer.
2) The charge/comm cables will also support in-unit battery charging. If in unit-battery
charging is required, please order the appropriate power supply with each charge/
comm cable.
3) This cable connects to a PC USB port.
MX7055CABLE
MX7 Charge/Comm Interface Cable, RS-232 Serial ActiveSync, D9 Female
Notes:
1) The Charge/Comm cables facilitate Active Sync directly from the MX7 Computer.
2) The charge/comm cables will also support in-unit battery charging. If in unit-battery
charging is required, please order the appropriate power supply with each charge/
comm cable.
3) This cable connects to a PC serial port.
MX7057CABLE
MX7 RS-232 Serial Adapter cable, 6in, for use with printers that provide their own
source of power. Non-RoHS.
MX7058CABLE
MX7 RS-232 Serial Adapter cable, 6in, for use with printers that provide their own
source of power.
MX7060CABLE
MX7 Headset coiled adapter cable, includes quick disconnect headset connector. A
headset isstill required.
HX2063CABLE
Cable, Vocollect TCO to LXE QD - Must also order MX7060CABLE or MX7070CABLE
Notes:
1) This cable should be ordered when using a Vocollect Headset. It has a Vocollect headset
connector on one end and the LXE 4-pin QX connector on the other. The total length of this
cable is 6”. One must also order MX7060CABLE to connect to the MX7.
MX7070CABLE
CBL ASSU, AUDIO, 6 INCH, MX7, includes quick disconnect headset connector.
Notes:
1) This is the MX7 Headset coiled adapter cable which includes the quick disconnect headset
connector. This new cable has the coiled section removed and the length has been reduced
to 6”.
STRAPS
MX7A401HANDSTRAP
Replacement MX7 Hand Strap
MISCELLANEOUS
MX7A584STYLUS
10 pack
MX7 Replacement Stylus , 10-pack
9000A510STYLUS
5 pack
Large tethered stylus which fit the MX7 carry cases, 5 pack
MX7A684PROTFILM
PICTURE UNAVAILABLE
CALL FOR AVAILABILITY
Touch screen Protectitive Film, 10 Pack
HEADSETS
LX-213
Single ear, single headband, headset with noise canceling boom microphone
Notes:
1) Adapter cable MX7060CABLE sold separately.
HX1506HSYOKE
Replacement head yoke for single band LX-213 headset, qty 1
HX1508WINDSCRN
10 pack
Replacement windscreen for all headset microphones, 10 pack
HX1509WINDSCRN
5 pks. of 10 ea.
Replacement windscreen for all headset microphones, 50 pack
9000512EARPAD
10 pack
Replacement leatherette ear piece cover for LX-213 and 502 headsets, 10 pack
9000513EARPAD
5 pks. of 10 each
Replacement leatherette ear piece cover for LX-213 and 502 headsets, 50 pack