TS® 44 PRO Test Set - Test Equipment Depot

99 Washington Street
Melrose, MA 02176
Phone 781-665-1400
Toll Free 1-800-517-8431
Visit us at www.TestEquipmentDepot.com
T S 4 4 P R O Te s t S e t
®
Durability and exterior:
The next-generation improvement over
Data Lockout override technology, the
TS44 PRO Test Set features ADSLSafe™
technology, allowing technicians to butt
in on a live ADSL line to test POTS quality
without downing the data service. With
our new waterproof case, the TS44 PRO
Test Set features the latest improvements
to DropSafe™ reliability and RainSafe™
• DropSafe 20 feet
• Enhanced weatherproof/waterproof
case design
• Mountable, top or bottom, extra large
steel locking belt clip
• Line cord strain relief
Features:
• Low profile keypad with
protection ridge
• Software upgradeable
• Low battery warning
protection, so it’s weatherproof for
• Mute indication
extreme conditions.
• Polarity indication
• Easy to use
• Tone and pulse
Handy features
• Two-way hands-free speakerphone
This easy-to-use unit comes with all the fea-
• One-way amplified speaker phone
tures that make a technician more productive,
mode (optional)
including a high-fidelity, two-way hands-free
• Amplified speaker
amplified speakerphone, speed dialing, a low
• Last number redial
battery warning indicator and a rugged over-
• Over voltage protection
sized locking belt clip for universal needs.
• Over current protection
Data protection:
• DataSafe including ADSLSafe
technology
• Data lockout with single button
override
Testing:
• Data indication/warning
• Mute
• PBX pause button
• Audible ringer
• Speed dialing
• Volume control levels
• Line and battery powered
• Passive monitor
• Hearing aid compatible
• Low and high voltage indication/
warning
• Low current (mA) indication/warning
For more information, or to contact your
local Fluke Networks representative, call
(800) 283-5853 or email
info@flukenetworks.com
See data and keep it safe while troubleshooting voice
Technical Data
TS44 PRO Test Set quick guide
TS44 PRO Test Set Specifications
Feature
Operation
Parameter
Data Test
Connect the unit to Tip and Ring and move the
Electrical
T/M switch to T. If high-speed data is present,
Current Range (Off-Hook)
the unit’s alarm will start beeping and the unit
DC Resistance
will lockout and not go off-hook. If there is no
Off-Hook
150 Ω nominal
On-Hook
>3 MΩ
AC Impedance Off-Hook
600Ω nominal; 300 Hz to 3400 Hz
On-Hook
>120 kΩ; 300 Hz to 3400 Hz
high-speed data, the unit will go off-hook.
Data Lockout Override
In Talk mode, while the data lockout alarm is
sounding, press the OVERRIDE key – the unit
will go off-hook. For example, this is what you
would do to access POTS on a line carrying
Line Voltage Test
Low Voltage
Normal Voltage
High Voltage
Loop Current Test
Working Limits
Rotary Dial Output
both POTS and ADSL.
Pulsing Rate
10 pps ±1 pps
In Monitor mode, press Vdc&mA/TEST key.
Break/Make Ratio
60/40
0 Vdc to 2 Vdc – LO LED lights up red for 3
Interdigit Interval
>300 ms >100 kΩ
seconds. 2 Vdc to 42 Vdc – LO LED flashes red.
Resistance During Break
42 Vdc to 53 Vdc – LO and HI LEDs flash green
DTMF Output
once.
Tone Frequency Error
±1.5 % maximum
53 Vdc to 140 Vdc – HI LED flashes red. >140
Tone Level
-3 dBm combined (typical)
Vdc – HI LED lights up red for 3 seconds.
High versus Low Tone
2 dB ± 2 dB
Go off-hook and press the Vdc&mA TEST key.
Difference
If the loop current is less than 23mA, the mA
Memory Dialing
LED flashes red. If the loop current is 23mA or
Memory Capacity
10 speed dial memories plus one last
number redial memory
greater, the mA LED flashes green.
Redial the Last Number
Go off-hook and press the LNR key.
Dialed
Pulse Dialing
Digit Capacity
23 digits per memory
PBX Pause Duration
4 seconds
By default the unit is configured to Tone dial.
Hook Flash Duration
User programmable; default of 600 ms
But if you want to Pulse dial, go off-hook and
Automatic Speaker Shut
User programmable; default of 2 minutes
press the TONE/PULSE key, now the unit will
Off Duration
pulse dial.
Battery
Program Speed Dial
In Monitor mode, press RCL. Enter the number
Numbers
to be stored. Press STORE/PROG, then press
Physical
the number of the memory location (0-9) where
you want to store it. The confirmation tone
sounds.
To Speed Dial a Stored
Go off-hook, press RCL, then press the key
Number
(0-9) of the memory location where the number
is stored.
Two-Way Speakerphone
10 mA to 100 mA
While off-hook, press SPKR to activate. Press
9 V alkaline or lithium battery
Measurement
10 in x 3.75 in x 4.25 in (254 mm x 96
mm x 107 mm)
Weight
Less than 1.5 pounds (0.68 kg) with one
belt clip
Water Resistance
Designed to be rain and moisture resistant.
Environmental
Temperature Range
SPKR again to deactivate. If you are listening
Operating:
29°F to 140°F (-34°C to 60°C)
only, press MUTE to activate the Receive-Only
Storage
-40°F to 150°F (-40°C to 66°C)
Loud Speaker. Press MUTE again to restore the
Altitude
To 10,000 ft. (3,000 m) max
two-way Speakerphone.
Drop
Two 20-foot drops and twelve 12-foot
To Set Receive-Only
1 Put the test set in Monitor mode.
Loud Speaker as
2 Press STORE/PROG.
Default
3 Press MUTE. The confirmation tone sounds.
To restore the Speakerphone as the default
drops onto concrete
Note
Specifications subject to
change without notice.
Speaker mode, repeat the three steps above.
Visit us at www.TestEquipmentDepot.com
Download PDF