2008-09 Chrysler 300 AE Page 1

2008-10
Chrysler 300
AbouttheVehicle
Make: Chrysler
Model: 300
Year: 2008-10
Standard/Optional
CD Player
6 Speaker 288-watt Boston Acoustics Stereo
In-dash CD changer
Navigation System
7 Speaker 380-watt stereo
MyGig Hard Drive Based Multi Media Source Unit
3.5mm AUX/USB Port/iPod Connectivity
pany
Photo by Ford Motor Com
SpeakerNotes
Front
InDashApplication
Dash Type :
Double DIN
Aftermarket:
Single/Double DIN
Kit:
CR1288B/CR1291B
Harness:
CR06SR
Antenna Adapter: VWA3B/VWA3RB
On the left side of the steering column.
Speaker Sizes
Front Dash:
3.5''
Lower Door:
6x9”
Speaker Adapter: SA69
Speaker Harness: TBA
Factory Assembly: (4) T-15 screws securing speaker.
Dimensions: Front Dash
W= 4.25''
L= 4.25''
D= 2.5''
Dimensions: Lower Door
W= 5.75''
L= 8.5''
D= 2.75”
NOTES
WireColorCodes
Type: Standard Audio System
Location: At Speakers
+12v Constant = Gray/Green
+12v Acc. Switch = CanBus DATA
-12v Chassis Ground= Black/Green
+12v Illumination = CanBus DATA
+12v Dimmer = CanBus DATA
Antenna/Amp Remote = CanBus DATA
Can-Bus = White & White/Orange
LF+ = Gray/Purple
LF- = Gray/Yellow
RF+ = Green/Purple
RF- = Green/Yellow
LR+ = Green/Orange
LR- = Green/Gray
RR+ = Green/Black
RR- = Yellow/Gray
Rear
Speaker Sizes
Rear Deck:
6x9''
Rear Deck:
8” Subwoofer
Speaker Adapter: SA69
Speaker Harness: TBA
Factory Assembly: (4) 9/32” bolts securing speaker.
Dimensions:
W= 5.75''
L= 8.5''
D=
NOTES
2008-10
Chrysler 300
Recommended: Disconnect negative battery cable
Radio Removal
1. Remove the rubber pad just in front of the shifter.
Extract (2) PHS from underneath the pad.
2. Using a PRT remove the trim around the shifter.
3. Using a PRT remove the whole trim panel that is
around the shifter that goes to the bottom of the
ash tray.
4. Using a PRT remove the ash tray trim panel.
5. Using a PRT remove the trim around the radio
and A/C controls.
6. Extract (4) PHS securing the radio to the dash.
Disconnect and remove.
Images
Radio
Front Speakers
Dash Speakers
1. Using a panel removal tool to remove the dash
speaker grille.
2. Extract (2) Screws securing speaker unplug and
remove speaker
Door Speakers
1. Use a pick tool to lift screw cover inside door
release area and extract (1) screw from behind.
2. Use a pick tool to lift screw cover just
below armrest and extract (1)
screw from behind.
3. Use a pick tool to to push in the pop-tab
fasteners on outer rim of door panel.
(1) Front, (2) on rear sill.
4. Extract (4) Phillips head screws from
lower door panel.
5. Use a panel removal tool to pop off door
panel, unplug and remove.
6. Extract (4) Torx T-15 screws from speaker,
unplug and remove.
Door Speakers
Dash Speakers
Rear Speakers
Rear Speakers
Rear Deck Speakers
1. Fold down rear seat sections.
2. Use a panel removal tool to pop out both rear “C”
Pillar panels.
3. Extract (1) 10mm bolt from each side bolster. Use
a panel removal tool to release the upper part
of the side bolsters and remove.
4. Use a panel removal tool to pop out (1) pop panel
fastener from the middle of the rear deck.
5. Remove rear deck tray by pulling up and out.
6. Extract (4) 9/32-7mm head screws from
speaker, unplug and remove.
Sub location
Rear Subwoofer
1. For premium-equipped vehicles with a Rear
Deck Subwoofer, follow the “Rear Deck Speaker”
removal steps.