Star QCS2-500 Star® QCS2 Conveyor Toaster Owner's Manual
Below you will find brief information for Conveyor Toaster QCS2, QCSe2, RCS2, R2e SERIES, Conveyor Toaster QCS3, QCSe3 SERIES. This document describes the operation and installation of the Holman Conveyor Toaster. It covers topics like assembly and installation, electrical connection, daily operation, programming and maintenance procedures.
Advertisement
Advertisement
CONVEYOR
®
TOASTER
MODEL
QCS2, QCSe2, RCS2, R2e SERIES
QCS3, QCSe3 SERIES
Installation and
Operation
Instructions
2M-Z10651 Rev. G 1/26/2015
Q2-600H-208V
1
SAFETY SYMBOL
These symbols are intended to alert the user to the presence of important operating and maintenance instructions in the manual accompanying the appliance.
RETAIN THIS MANUAL FOR FUTURE REFERENCE
NOTICE
Using any part other than genuine Star factory supplied parts relieves the manufacturer of all liability.
Star reserves the right to change specifications and product design without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment.
Due to periodic changes in designs, methods, procedures, policies and regulations, the specifications contained in this sheet are subject to change without notice. While Star International Holdings Inc., Company exercises good faith efforts to provide information that is accurate, we are not responsible for errors or omissions in information provided or conclusions reached as a result of using the specifications. By using the information provided, the user assumes all risks in connection with such use.
MAINTENANCE AND REPAIRS
Contact your local authorized service agent for service or required maintenance.
Please record the model number, serial number, voltage and purchase date in the area below and have it ready when you call to ensure a faster service.
Model No.
Authorized Service Agent Listing
Reference the listing provided with the unit
Serial No.
Voltage
or for an updated listing go to:
Website:
E-mail www.star-mfg.com [email protected]
Purchase Date
Service Help Desk
Business
Hours:
8:00 am to 4:30 p.m. Central Standard Time
Telephone:
Fax:
(314) 678-6303
(314) 781-2714
Website: [email protected]
www.star-mfg.com
Mailing Address: Star International Holdings Inc., Company
10 Sunnen Drive
St. Louis, MO 63143
U.S.A
2
2
TABLE OF CONTENTS
General Installation Data ......................................................4
Uncrating & Inspection .........................................................4
Assembly & Installation .......................................................4
Electrical Connection ............................................................4
QCS & RCS
Operation .............................................................................5
Cooking Procedures ............................................................5
Toaster Components ............................................................5
Daily Operation ...................................................................6
Operating Hints & Safety ....................................................6
QCSe & RCSe
QCSe Operation ..................................................................7
Start-up ................................................................................8
Daily Operation ...................................................................8
Operating Hints & Safety ....................................................8
Toaster Components ............................................................8
Programing
Conveyor Speed .................................................................9
Programing Values for Menu Items ...................................9
Cleaning ...............................................................................10
Maintenance Procedures ......................................................11
Trouble Shooting Guide .......................................................12
Warranty ...............................................................................13
Wiring Diagrams
QCS2 & 3, RCS2 & 3, wired series ...................................14
QCS2 & 3, RCS2 & 3, wired parallel ................................14
QCS2 & 3, RCS2 &3, 3 wired in series .............................15
QCS2, RCS2 w/fan switch series .......................................15
QCS2 & 3, RCS2 & 3, 3 wired in series w/bun mode .......16
QCSe, 4 wired in series ......................................................16
QCSe, 6 wired in series ......................................................17
QCSe, 6 wired in parallel ...................................................17
QCS3, 6 wired in series, with fuses ....................................18
R2-600N & R2-600BN ......................................................18
Exploded View / Parts List
R2-600N (Narrow) .............................................................20
QCS2 & 3, RCS2 & 3 ........................................................22
3
CAUTION
GENERAL INSTALLATION DATA
This equipment is designed and sold for commercial use only by personnel trained and experienced in its operation and is not sold for consumer use in and around the home nor for use directly by the general public in food service locations.
Before using your new equipment, read and understand all the instructions & labels associated with the unit prior to putting it into operation. Make sure all people associated with its use understand the units operation & safety before they use the unit.
All shipping containers should be checked for freight damage both visible and concealed. This unit has been tested and carefully packaged to insure delivery of your unit in perfect condition. If equipment is received in damaged condition, either apparent or concealed, a claim must be made with the delivering carrier.
Concealed damage or loss - if damage or loss is not apparent until after equipment is unpacked, a request for inspection of concealed damage must be made with carrier within 15 days. Be certain to retain all contents plus external and internal packaging materials for inspection. The carrier will make an inspection and will supply necessary claim forms.
INSPECTION & ASSEMBLY
UNCRATING AND INSPECTING
Unpack the unit and components from the shipping container. Remove all visible packing material and those from inside the cooking chamber. If damage is discovered, file a claim immediately with the carrier that handled the shipment. Do not operate the unit if it was damaged during shipping.
ASSEMBLY AND INSTALLATION
The unit was shipped fully assembled and ready to plug into a standard outlet specified for its voltage and amp draw. If improper electrical supply is determined, contact a qualified electrician prior to using the unit. Removal and replacement of the power cord and plug will void the warranty. For assistance, contact your local authorized service agent for service or required maintenance.
Level unit using the adjustable feet under the unit (approximately 1/2" adjustment).
Before using the unit for the first time, wipe down the exterior with a damp cloth.
Allow enough space around the toaster for adequate ventilation. Do not operate the unit without the crumb tray properly positioned. Overheating and poor toasting may occur. Read all labels on the unit and follow their instructions.
CAUTION
WARNING
ELECTRICAL CONNECTION
Before making any electrical connection to this unit, check that the power supply is adequate for the voltage, amperage and requirements stated on the rating plate.
A wiring diagram is included herewith.
Disconnect the unit from the power source before installing or removing any parts.
Be absolutely sure that the ground connection for the receptacle is properly wired. Do not connect equipment to power without proper ground connections. Improper grounding may result in personal injury or fatality.
WARNING
DO NOT CUT OR REMOVE THIS PLUG OR GROUNDING PRONG FROM THE
PLUG.
CONNECT/PLUG UNIT INTO DEDICATED A.C. LINE ONLY SPECIFIED ON THE
DATA PLATE OF THE UNIT.
4
QCS
® e
OPERATION
ROTARY POWER SAVER SWITCH
For toasters equipped with a Rotary Power Saver Switch, turn clockwise or counterclockwise to get in the following positions.
FULL POWER
When in this position your equipment is at full power and ready to use.
OFF ROTARY
Two off positions are provided, a single rotation to either direction will shut the unit off.
STANDBY
The standby position reduces the power consumption by 75%. Using this position during the quiet times will save electricity, and keep the toaster warm. When needed, turn the switch to FULL POWER.
Recovery time is about 30 seconds.
CAUTION
CERTAIN SURFACES ARE EXTREMELY HOT DURING OPERATION AND CARE
SHOULD BE TAKEN WHILE USING THIS UNIT.
COOKING PROCEDURES
BREAD TOASTING
Some toasters are equipped with a swinging heat shutter at the toaster entrance. This shutter will move out of the way as the product passes under it.
1) Turn the power saver to FULL POWER.
2) Set the conveyor speed to HIGH.
3) If your toaster is equipped with separate top and bottom heat controls set them both at HIGH.
4) Allow warm up time of 5 to 10 minutes.
5) Place a sample product on the conveyor belt to test the settings.
•If toasting is too light, turn conveyor speed control counterclockwise to a slower speed.
•If toasting is too dark, turn heat control to a lower heat.
(NOTE: Some products may require adjustment of the top and bottom heat controls in order to achieve the desired results)
TOASTER COMPONENTS
FRONT
LOAD UP
HIGH LIMIT RESET
CRUMB TRAY
SPEED CONTROL
HEAT CONTROLS
POWER SAVER SWITCH
IL1386
AIR INTAKE FAN
POWER CORD
5
CAUTION
QCS
® e
DAILY OPERATION
Check the power cord to insure that it is plugged into a proper outlet.
Set the heat control knobs to desired temperature.
Always allow 10 minutes of preheat time before loading the unit with product. Failure to allow sufficient preheat time will result in unsatisfactory cooking until the unit reaches operating temperature.
OPERATING HINTS AND SAFETY
Disconnect power to the unit with the switch at the end of each day of operation.
Do not leave the unit in operation without an attendant.
Turn Power Saver Switch to Standby during idle periods. It will take only a few minutes to regain operating temperature.
Do not leave the unit at high temperature when not in use or during idle periods.
This will cause food particles and grease film to carbonize.
6
QCS
QCSe & RCSe OPERATION
The Holman QCSe conveyor toaster comes with pre-programmed factory default settings for TOAST,
MUFFINS, and BAGELS. The operator may change these setting at any time. A button labeled OTHER is provided to allow the operator to program settings for additional product(s). e
®
Press TOAST and TST will appear in the display.
Press MUFFIN and MUF will appear in the display.
Press BAGEL and BGL will appear in the display.
Press OTHER and OTH will appear in the display.
LIGHT and DARK buttons are used to change the conveyor speeds when in toast, muffin, or bagel modes.
Pressing the (LIGHT) button once will increase the conveyor speed by 15%. Pressing twice (XLIGHT) will increase the conveyor speed by
30%.
Pressing the
(DARK) button once will decrease the conveyor speed by 10%. Pressing twice
(XDARK) will decrease the conveyor speed by
20%.
Note: After 60 seconds the conveyor speed will return to the preprogrammed setting.
The factory default settings are as follow:
TOAST AND OTHER BAGEL:
TOP HEAT 9
BOTTOM HEAT 9
CONVEYOR 59
TOP HEAT
BOTTOM HEAT
CONVEYOR
9
9
24
OTHER:
TOP HEAT 9
BOTTOM HEAT 9
CONVEYOR 59
POWER SAVER:
TIME (minutes)
HEAT
60
5
The QCSe toaster is equipped with a Power Saver Switch (SAVER) that reduces the power used by the toaster after a pre-programmed period of time. This Power Saver Switch has three modes:
ON: Unit is in pre-programmed power saving setting.
OFF: Power Saver mode is turned off.
AUTO ON: Power Saver turns on when there has been no activity for a programmed length of time.
The operator may adjust the level of power reduction for the saver mode. (Note: conveyor may move slowly when in saver mode.)
Two buttons (+) and (-) are used when increasing or decreasing the value of each programmable setting.
A red LED light located at the lower portion of the control panel label will indicate if the value for top heat, bottom heat or conveyor speed is being adjusted.
7
CAUTION
QCS
® e
CERTAIN SURFACES ARE EXTREMELY HOT DURING OPERATION AND CARE SHOULD
BE TAKEN WHILE USING THIS UNIT.
START UP
When the toaster has been plugged into a suitable outlet and power supply, the word OFF will be displayed on the L.E.D. read out.
A. Press the ON/OFF button once to turn on the toaster. The toaster will now enter into pre-heat and
PREHT will be displayed (the elements will begin to glow but the conveyor and fan motor will not turn on).
B. After one minute, the fan motor will turn on and the conveyor will begin turning at the previously saved setting (for initial start up, the drive motor will operate at the factory default setting).
C. After four minutes, the display will show the last used program selection i.e. TOAST, BAGEL,
MUFFIN or OTHER (for initial startup, TOAST will be the last program selected).
DAILY OPERATION
Check the power cord to insure that it is plugged into a proper outlet.
Press the ON/OFF button once to turn the toaster on.
Press the button a second time to turn the toaster off.
NOTE: When the toaster is turned off, the fan and conveyor motors will continue to run for five minutes.
The words COOL and DOWN will be alternately displayed during that time. After five minutes, the word
OFF will be displayed until the ON/OFF button is pressed again.
For units equipped with a
POWER SAVER feature, the three operating modes are:
ON
OFF
AUTO
Unit has entered the pre-programmed level of power savings.
Power Saver feature is turned off.
If the toaster has been idle for a pre-set period of time, the unit enters Power Saver mode until one of the menu buttons has been pressed.
Once the toaster has been pre-heated, the menu buttons can be pressed to change to
TOAST, BAGEL,
MUFFIN, or OTHER.
CAUTION
OPERATING HINTS AND SAFETY
Disconnect power to the unit with the ON/OFF button at the end of each day of operation.
Do not leave the unit in operation without an attendant.
Do not leave the unit at high temperature when not in use or during idle periods. This will cause food particles and grease film to carbonize.
TOASTER COMPONENTS
FRONT
HIGH LIMIT RESET
LOAD UP
CRUMB TRAY
LCD DISPLAY
CONTROLS
AIR INTAKE FAN
IL1385
POWER CORD
8
QCS
® e
PROGRAMING
A. CONVEYOR SPEED (temporary setting)
The conveyor speed is programmable with a range from 0 to 99 with 0 being the slowest and 99 being the fastest. Each menu item can have independent conveyor speed settings.
The LIGHT and DARK buttons can be used to temporarily change the conveyor speed.
Pressing the LIGHT button once will increase the conveyor speed by 15%. The word
LIGHT
will be displayed. Pressing twice will increase the conveyor speed by 30% and
XLIGHT will
now be displayed.
Pressing the DARK button once will decrease the conveyor speed by 15%. The word
DARK
will be displayed. Pressing twice will decrease the conveyor speed by 30% and
XDARK will
now be displayed.
NOTE: After 60 seconds, the conveyor speed will return to the pre-programmed setting.
WHEN USING THE LIGHT AND DARK BUTTONS TO ADJUST THE CONVEYOR SPEED
FOR A SINGLE ORDER OF PRODUCT, IT IS IMPORTANT TO REMEMBER TO ALLOW
THE PRODUCT ALREADY IN THE TOASTER TO EXIT BEFORE CHANGING THE
SPEED SETTING.
B. PROGRAMING VALUES FOR MENU ITEMS
To make a program change to the top heat, bottom heat, or conveyor speed, you must first be in the menu item you want changed. Example: to change the programmed conveyor speed for bagels, the display must read BAGEL. To change the programmed conveyor speed for TOAST, the display must read
TOAST and so on for each menu item.
1) Select the menu item you want to change i.e. TOAST, MUFFIN, BAGEL or OTHER.
2) Press and hold both ( + ) AND ( - ) buttons for 3 seconds until the display goes blank, release the buttons and the display will show three characters for the menu item elected and the last two characters for the current value setting, i.e.
TST, MUF,
BGL and OTH. The red L.E.D. light for top heat at the bottom of the label will flash.
3) Press the ( + ) or ( - ) buttons to increase or decrease the setting for the top heat.
4) Press the button for the menu button again and the red L.E.D. for the bottom heat will flash.
5) Press the ( + ) or ( - ) buttons to increase or decrease the setting for the bottom heat.
6) Press the button for the menu button again and the red L.E.D. for the conveyor speed will flash.
7) Press the ( + ) or ( - ) buttons to increase or decrease the setting for the conveyor speed.
8) To skip one feature setting with out making any changes, press the menu item button one time and the red L.E.D. light for the next item will now flash.
9) To change the POWER SAVER values press the SAVER button or to save your new setting(s), and exit the program mode press the menu button.
10) The last two characters in the display will show MN for minutes.
11) The first three characters will be numerical to represent the time setting.
12) Press the ( + ) or ( - ) buttons to increase or decrease the setting for the savor mode time. The minimum value is 15 minutes to maximum value of 480 minutes.
13) Press the SAVER button to change the power reduction using the ( + ) or ( - ) buttons to increase or decrease the setting.
14) Press the POWER SAVER button to save changes and to exit.
9
QCS
® e
QCS e
®
WARNING
CLEANING
Preventive maintenance for your Holman toaster consists of the following recommended cleaning procedures. To keep your toaster in its top operating condition, these steps should be performed on a daily or weekly as indicated.
A. Clean air intake on bottom of unit.
B. For lightly soiled conveyor belts, turn conveyor speed control to fastest setting (100) and wipe with a damp cloth (daily) For heavily soiled conveyors, turn conveyor speed control to fastest setting and wipe with a light abrasive pad (as needed).
C. Turn main power saver switch to the OFF position. Disconnect unit from power source.
D. After the unit cools, remove interior crumb tray (as shown below) and clean.
Slide crumb tray back into position.
E. Wipe exterior surface of unit.
DO NOT IMMERSE OR LET THE UNIT
STAND IN WATER.
DO NOT HOSE DOWN THE UNIT OR THE
TABLE/COUNTER IF THE UNIT IS ON THE
TABLE/COUNTER.
KEEP AWAY FROM RUNNING WATER.
OPERATE
CLEAN
CRUMB TRAY REMOVAL
10
MAINTENANCE PROCEDURES
A. REPLACING HEATER TUBES
1)
DISCONNECT UNIT FROM POWER SOURCE.
2) Remove the enclosure.
3) Remove heater tube wire from terminal block connection, keeping top and bottom wires separate.
4) Lift heater tube retainers by loosening retaining screws and sliding the retainer plate up.
Hand tighten the plate to hold it up so the heater tubes will slide out freely.
5) Gently, pull defective heater tube out of unit.
6) Gently, put new heater tube into unit.
7) Loosen retainer screws and slide the retainer back into place. Tighten the screw to secure the retainer in place over the ends of the heater tubes.
B. REPLACING FAN MOTOR
1) DISCONNECT UNIT FROM POWER SOURCE.
2) Remove screws from the enclosure and the back panel at rear of unit.
3) Remove the enclosure and the back panel.
4) Unplug power supply cord from fan motor.
5) Remove (4) screws, which hold fan motor and grill to bottom of unit and remove fan.
6) Put replacement motor and grill in place and secure to the bottom of unit with screws.
7) Reconnect power supply cord to fan motor.
8) Replace back panel and enclosure. Fasten with screws removed in step 2.
C. REPLACING BELT DRIVE MOTOR
1)
DISCONNECT UNIT FROM POWER SOURCE.
2) Remove enclosure and back panel.
3) Remove sprocket from motor shaft, using an Allen wrench and loosening the set-screw.
4) Remove the wire from terminal block connecting the drive motor to internal wiring.
On units rated 208 or 240 volts, note which color leads are being used for these connections and which lead is capped with white tape. The new motor should use the same arrangement.
5) Remove screws holding motor in place and remove motor from unit.
6) Put new motor in place and attach loosely with mounting screws.
7) Replace sprocket on motor shaft.
NOTE: The two sprockets should line up parallel with each other, so the chain does not twist any during operation. Also the hub gets installed closets to the motor.
8) Slide motor until the drive chain has about 1/4” slack when lightly pushed at the center of its top open run. See chain tensioning illustration.
9) Tighten screws to secure motor.
10) Rewire leads same as removed in step 4.
11) Replace side panel and control box cover.
D. CLEANING AIR INTAKE
ONCE A WEEK
1)
DISCONNECT UNIT FROM POWER SOURCE.
2) Place unit on its backside.
3) Use a vacuum cleaner and or a damp cloth to clean the air intake. This procedure should be done at least once a week.
E. LUBRICATE THE CHAIN & SPROCKETS
EVERY 6 MONTHS
1)
DISCONNECT UNIT FROM POWER SOURCE.
2) Remove enclosure exposing chain drive.
3) Using an extreme pressure, synthetic chain lubricant with a temperature range up to 400°F. Apply liberally onto chain and sprockets. This grease is available as part no.
1L-Z12397.
4) Replace enclosure, Reconnect power source and test unit.
1/4”
QCS/RCS Chain Tension
11
TROUBLESHOOTING GUIDE
A. UNIT WILL NOT HEAT, CONVEYOR BELT WILL NOT MOVE.
1) Be sure the main circuit breaker is switched to the ON position.
2) Check to see if the toaster is plugged in and all controls are turned to the ON position.
B. UNIT HAS HEAT ONLY ON ONE SIDE, CONVEYOR BELT TURNS FREELY.
1) Call the Star Service Help Desk at (314) 678-6303, as heating element may need replacing.
C. CONVEYOR WILL NOT TURN, UNIT HEATS PROPERLY.
To check for mechanical binding:
1)
DISCONNECT UNIT FROM POWER SOURCE.
2) Remove 2 screws holding enclosure to the bottom of the unit.
3) Set unit on the legs and remove 4 screws on the back of the toaster.
4) Slide the enclosure off the unit and remove the back panel.
5) Loosen the four screws that hold the drive motor in place.
6) Slide the motor up allowing the drive chain to be removed from the sprockets.
7) Move the conveyor belt by hand to check for mechanical binding. If conveyor moves freely, call the Star Service Help Desk at (314) 678-6303, as the drive motor and/or speed control may need replacing.
8) Replace the enclosure by sliding it forward towards the front of the unit.
The front edge of the enclosure will slide beneath the toaster front.
D. HEAT LIMIT SWITCH (RESET)
Your Holman conveyor toaster is equipped with an automatically activated heat limit switch that interrupts the heater tube connections if the ambient temperature in the control box exceeds
190°F (88C). This switch can be reset manually by pushing the red button under the toaster as shown in the Toaster Components Illustration on Page 5 & 8.
1)
DISCONNECT UNIT FROM POWER SOURCE.
2) Check to see if air intake area in the bottom center of the control box cover is free of dust, grease or other obstructions.
3) Check if crumb tray is in place. NEVER OPERATE UNIT WITHOUT CRUMB TRAY IN PLACE
AS THIS CAUSES OVERHEATING IN THE CONTROL BOX.
4) If no obstructions to the airflow can be found and if the crumb tray is in place, call the Star Service Help Desk at (314) 678-6303 or email; [email protected] for assistance, or contact an authorized service agent near you.
E. CONVEYOR TURNS AT ONE SPEED REGARDLESS OF SPEED
CONTROL SETTING.
1) Call the Star Service Help Desk at (314) 678-6303 or email; [email protected], as speed control should be replaced, or contact an authorized service agent near you.
F. PRODUCT STICKING TO CONVEYOR OR SLIDE
Your Holman conveyor toaster is designed to toast product that is at current room temperature.
DO NOT attempt to put frozen, refrigerated, or any butter or a butter substitute material in the toaster. Doing so may cause it to come out doughy or very moist, as well as possibly sticking to parts of the unit.
1) Follow the cleaning procedures listed on page 10.
12
Visit our Website at: www.star-mfg.com Email: [email protected]
THOROUGHLY INSPECT YOUR UNIT ON ARRIVAL
This unit has been tested for proper operation before leaving our plant to insure delivery of your unit in perfect condition. However, there are instances in which the unit may be damaged in transit. In the event you discover any type of damage to your product upon receipt, you must immediately contact the transportation company who delivered the item to you and initiate your claim with same. If this procedure is not followed, it may affect the warranty status of the unit.
LIMITED EQUIPMENT WARRANTY
All workmanship and material in Star products have a one (1) year limited warranty on parts & labor in the United States and Canada. Such warranty is limited to the original purchaser only and shall be effective from the date the equipment is placed in service. Star's obligation under this warranty is limited to the repair of defects without charge, by the factory authorized service agency or one of its sub-agencies. Models that are considered portable (see below) should be taken to the closest Star service agency, transportation prepaid.
>
Star will not assume any responsibility for loss of revenue.
>
On all shipments outside the United States and Canada, see International Warranty.
*
The warranty period for the Ultra-Max, Hot Plates, Griddles, Charbroilers is (3) years parts & labor.
*
The warranty period for the Star-Max, Charbroilers, Griddles, Hot Plates, Fryers & Finishing Oven is (2) years parts & labor.
*
The warranty period for the JetStar six (6) ounce & Super JetStar eight (8) ounce series popcorn machines is two (2) years.
*
The warranty period for the Chrome-Max Griddles is five (5) years on the griddle surface. See detailed warranty provided with unit.
*
The warranty period for Dura-Tec coatings is one year under normal use and reasonable care. This warranty does not apply if damage occurs to
Dura-Tec coatings from improper cleaning, maintenance, use of metallic utensils, or abrasive cleaners, abrasive pads, product identifiers and point-of-sale attachments, or any other non-food object tha comes in continuous contact with the roller coating. This warranty does not apply to the
“non-stick” properties of such materials.
>
This warranty does not apply to "Special Products" but to regular catalog items only. Star's warranty on "Special Products" is six (6) months on parts and ninety (90) days on labor.
>
This warranty does not apply to any item that is disassembled or tampered with for any purpose other than repair by a Star Authorized Service Center or the Service Center's sub-agency.
>
This warranty does not apply if damage occurs from improper installation, misuse, wrong voltage, wrong gas or operated contrary to the Installation and
Operating instructions.
>
This warranty is not valid on Conveyor Ovens unless a "start-up/check-out" has been performed by a Factory Authorized Technician.
PARTS WARRANTY
Parts that are sold to repair out of warranty equipment are warranted for ninety (90) days. The part only is warranted, the labor to replace the part is NOT warranted.
SERVICES NOT COVERED BY WARRANTY
1. Travel time and mileage rendered beyond the 50 mile radius limit
2. Mileage and travel time on portable equipment (see below)
3. Labor to replace such items that can be replaced easily during a daily cleaning routine, ie; removable kettles on fryers, knobs, grease drawers on griddles, etc.
4. Installation of equipment
5. Damages due to improper installation
6. Damages from abuse or misuse
7. Operated contrary to the Operating and Installation Instructions
8. Cleaning of equipment
9. Seasoning of griddle plates
10. Voltage conversions
11. Gas conversions
12. Pilot light adjustment
13. Miscellaneous adjustments
14. Thermostat calibration and by-pass adjustment
15. Resetting of circuit breakers or safety controls or reset buttons
16. Replacement of bulbs
17. Replacement of fuses
18. Repair of damage created during transit, delivery, &
PORTABLE EQUIPMENT
Star will not honor service bills that include travel time and mileage charges for servicing any products considered "Portable" including items listed below.
These products should be taken to the Service Agency for repair: installation OR created by acts of God
* The Model 510FD, 510FF Fryer.
* The Model 526TOA Toaster Oven.
* The Model J4R, 4 oz. Popcorn Machine.
* The Model 518CMA & 526CMA Cheese Melter.
* The Model 12MC & 15MC & 18MCP Hot Food Merchandisers.
* The Model 12NCPW & 15NCPW Nacho Chip/Popcorn Warmer.
* All Hot Dog Equipment except Roller Grills & Drawer Bun Warmers.
* All Nacho Cheese Warmers except Model 11WLA Series Nacho Cheese Warmer.
* All Condiment Dispensers except the Model HPD & SPD Series Dispenser.
* All Specialty Food Warmers except Model 130R, 11RW Series, and 11WSA Series.
* All QCS/RCS Series Toasters except Model QCS3 & RCS3 Series.
* All Fast Steamer Models except Direct Connect Series.
ALL:
* Pop-Up Toasters
* Butter Dispensers
* Pretzel Merchandisers
(Model 16PD-A Only)
* Pastry Display Cabinets
* Nacho Chip Merchandisers
* Accessories of any kind
* Sneeze Guards
* Pizza Ovens
(Model PO12 Only)
* Heat Lamps
* Pumps-Manual
The foregoing warranty is in lieu of any and all other warranties expressed or implied and constitutes the entire warranty.
FOR ASSISTANCE
Should you need any assistance regarding the Operation or Maintenance of any Star equipment; write, phone, fax or email our Service Department.
In all correspondence mention the Model number and the Serial number of your unit, and the voltage or type of gas you are using.
2M-4497-2 11/21/14
13
14
15
20 BLACK
FUSE
FUSE
3 BLACK
2 WHITE
4 WHITE
4 WHITE
HT2 HB2
16
HT2 HB2
HT2 HB2
17
FUSE
FUSE
16 WHITE
2 WHITE
4 WHITE
RCS-2-600N
4 WHITE
9 BLACK
RIGHT SIDE
(CONTROLS)
RCS-2-600BN
QCS-3, 6 ELEMENTS WIRED SERIES WITH FUSES
RIGHT SIDE
(CONTROLS)
BLK
RESET/HIGH
LIMIT
DRIVE
MOTOR
2M-Z16972 rev~
COOLING
FAN
BLU
BLK
SPEED
CONTROL
BLK
GND
BLK
WHT
WHT
POWER SUPPLY
18
RESET/HIGH
LIMIT
BLK
DRIVE
MOTOR
COOLING
FAN
BLU
BLK
SPEED
CONTROL
BLU FOR
120/240V
WHT FOR 208V
2M-Z16803 revA
BLK
WHT
GND
BLK
WHT
POWER SUPPLY
19
3
2
1
Nameplate
6 7
8
9
10
42
41
33
35
34
36
39
40
37
38
31
30
29
28
27
26
25
24
32
MODEL: R2-600N:
Narrow Conveyor Toaster
20
4
5
11
12
22
23
18
19
20
21
17
8 12
12
14 15
16
SK2664 Rev. B 12/18/15
PARTS LIST
December 18, 2015
21
22
23
24
25
15
16
17
18
19
12
13
14
31
32
33
34
35
36
37
38
Fig No
1
2
3
4
9
10
7
8
5
6
11
20
26
27
28
29
30
Part Number
2C-6349
HC-Z16791
HC-120325
HC-120326
2E-200566
2A-200284
2C-200149
HA-112263
HC-Z16924
2A-Z16808
2N-Z16958
2N-Z16788
2C-08-07-0207
2P-Z8779
2P-200648
2P-150013
HA-120240
2K-8043
2E-Z9736
2K-Y2968
2R-200709
2R-Z18201
2U-200558
2R-200562
2C-Z9632
HB-120259
2E-Z3808
2M-Z16977
2M-Z16804
Z1-70-07-0343
2M-12-07-0038
2I-05-07-0013
2R-200768
HA-120352
2R-200708
HC-120324
PS-Z20951
HC-Z16795
PS-Z16937
2C-200004
2A-Z16807
HA-Z9743
Model: R2-600 Narrow Conveyor Toaster
Qty Description
16 SCREW #8X3/8 B THP STL NP
1 BACK PANEL R2N
1 BODY COVER ASSY R2N
1 HEAT BAFFLE ASSEMBLY R2N
1 SWITCH, RESET, 0796
1 E-CLIP 5/16”
1 FLAT WASHER 5/16 ID 31NWX
2 BEARING ASSY PTFE/BRONZE
1 SHAFT ACCESS COVER PLATE
1 DRIVE ASSEMBLY R2N
2 ELEMENT, SERPENTINE R2N, 120V
1 ELEMENT, SERPENTINE R2BN, 120V
14 NUT 10-24 HEX STL NP
1 SPROCKET 25P-11T .313 ID
1 SPROCKET, 25B32 X 5/16
1 DRIVE CHAIN #25 ROLLER
1 MOTOR ASSEMBLY
1 BUSHING
1 TERMINAL BLOCK, POWER
1 BUSHING - HEYCO 7W-2
4
LEG 1 INCH CHROME PLASTIC
FOOT 1.69X1 SIL 1/4 20
1 MOTOR,FAN 120V,15BTL
1 FAN GUARD
4 10-32 X 1/2 SCREW FZA
1 SPEED CONTROL ASSY 25O OHMS
1 SWITCH(EATON)-30A@120V,
1
FRONT PANEL GRAPHIC R2N
FRONT PANEL GRAPHIC R2BH
1 SWITCH GUARD
1 LABEL ON & OFF
1 BOOT SWITCH
1
KNOB, CONTROL Q SERIES
KNOB ASSY, CONTROL SPEED
1 KNOB, CONTROL CAP
1 LOWER TRAY ASSEMBLY R2N
1 CRUMBTRAY ASSY. 5”
1 CRUMB TRAY R2N
1 BURN GUARD FAB’D R2N w/HRDW
9 SCREW 6-32X5/16 THP SS
1 IDLER ASSEMBLY R2N
2 SPRING RETAINER (2)
Application
R2-600N, R2-60CN
R2-600BN, 60BCN
R2-60BCN, R2-60CN
R2-600N, R2-60CN
R2-600BN, R2-60BCN
R2-60BCN, R2-60CN
21
PARTS LIST
December 18, 2015
Fig No
39
40
41
42
NI
NI
NI
Part Number
2P-200700
2P-200736
2K-70436
PS-Z16768-39
2M-Z16803
2M-Z16972
HA-120241
Model: R2-600 Narrow Conveyor Toaster
Qty Description
2 BEARING-PTFE SPRING LOAD
2 2 INCH BEARING SPRING
1 BUSHING SNAP HEYCO 5/8
1 CONVEYOR ASSY
1 WIRING DIAGRAM
1 WIRING DIAGRAM
1 CORD ASSY
Application
R2-600BN
R2-600N
22
1
40
14
15 41
8
42
32
31
30
29
39
38
33
34
35
36
37
45 46
28
24
22
23
27
26
Certain Models or
Q2-3KL-KIT
SOME ITEMS ARE INCLUDED FOR
ILLUSTRATIVE PURPOSES ONLY AND IN
CERTAIN INSTANCES MAY NOT BE AVAILABLE
This drawing contains information confidential to Star Manufacturing International, Inc.
No reproduction or disclosure of its contents is permitted.
25
Model
Q2/Q2E/RCS2/Q3/Q3E Conveyor Toaster
23
2
3
4
5
6
18
17
20
21
16
15
14
19
13
43
44
7
8
9
10
11
12
SK2297 Rev.B 4/24/08
®
PARTS LIST
January 26, 2015, Rev. G
Models:
Q2-500-120V, Q2E-500-120V, Q2-500-CUL20, Q2-600H-CE, Q2-600H-UK, Q2-600HF-208, Q2-600H-208/220/240V,
Q2-600HS-208, Q2E-600H-208/240V, Q2-800-208/220/240V, Q2-800-240UK, Q2-800-230CE, Q2E-800-208/240V,
Q2-1200B-208/240V, R2-12BSZ-208/240V, R2--1200-208/240V, R2-600HJ-208/240V, R2-800-208V
CONVEYOR TOASTERS
Fig No Part No.
Qty
1 HC-120258 1
Description
ENCLOSURE ASSY - QCS-2
2
3
4
5
6
7
8
9
10
11
HB-120270
HB-120280
2R-Z8879
HA-120243
HA-120240
HB-120262
HC-120290
2U-200559
2U-200560
2U-200561
HC-Z10412
2A-202900
HA-112263
2P-Z8779
2P-150013
2P-150015
2P-200645
2P-200648
TOP BAFFLE ASSY QCS-2 LOW
1
BAFFLE ASSEMBLY, HIGH
1 2-5/8” DIA. FAN BLACK CW
MTR, ASSY QCS, 220/230/240
MOTOR ASSY 120V
1
MOTOR ASSY 208-240V
1
MOTOR ASSY 230V-50HZ
FAN 120V
FAN 240V
MOTOR, FAN240V 23BTM
1 BACK PANEL QCS-2
1 SHAFT, T710 DRIVE
2 BEARING ASSY, PTFE/BRONZE
1 SPROCKET, 25P-11T .313 ID
1
1
DRIVE CHAIN #25
CHAIN DRIVE #25
SPROCKET, 25B17 X 5/16”
SPROCKET, 25B32 X 5/16
Application
ALL
Q2-800-208/220/240V, Q2-1200B-208/240V, R2-12BSZ-208/240V, R2-1200B-
208/240V, R2-600HJ-208/240V, Q2-500-120V, Q2-500-CUL20, Q2E-500-120V, Q2E-
500CUL20, Q2-800-240UK
Q2-600H-208/220/240V , Q2E-600H-208/240V, Q2E-800-208/240V, Q2-600H-CE
OLDER MODEL MOTORS
Q2-600H-CE, Q2-600H-UK, Q2-800-240UK, Q2-800-230CE
Q2-500-120V, Q2-500-CUL20, Q2E-500-120V, Q2E-500CUL20, R2E-500-120V
Q2-600H-208/220/240V, Q2-800-208/220/240V, Q2-1200B-208/240V, R2-12BSZ-
208/240V, R2-1200B-208/240V, R2-600HJ-208/240V, Q2E-600H-208V, Q2-800-
240UK, R2E-800-208V, R2E-12BK
Q2-12B-230CE
Q2E-500-120V, Q2E-500CUL20
Q2-600H-208/220/240V, Q2-800-208/220/240V, R2-600HJ-208/240V, Q2E-600H-
208V, Q2E-800-208/240V, Q2-500-120V, Q2-500-CUL20, Q2E-500-120V, Q2-600H-
CE, Q2-600H-UK, R2E-800-208V
Q2-1200B-208/240V, R2-12BSZ-208/240V, R2-1200B-208/240V, R2E-12BK-208V
ALL
ALL
Q2-600H-208/220/240V, Q2-800-208/220/240V, R2-600HJ-208/240V, Q2E-600H-
208V, Q2E-800-208/240V, Q2-500-120V, Q2-500-CUL20, Q2E-500-120V, Q2E-
500CUL20, Q2-600H-CE, Q2-600H-UK, R2E-800-208V, Q2-1200B-208/240V, R2-
12BSZ-208/240V, R2-1200B-208/240V, R2E-12BK-208V
ALL
Q2-600H-208/220/240V, Q2-800-208/220/240V, R2-600HJ-208/240V, Q2E-600H-
208V, Q2E-800-208/240V, Q2-500-120V, Q2-500-CUL20, Q2E-500-120V, Q2E-
500CUL20, R2E-800-208V
Q2-1200B-208/240V, R2-12BSZ-208/240V, R2-1200B-208/240V, R2E-12BK-208
Q2-600H-208/220/240V, Q2-800-208/220/240V, R2-600HJ-208/240V, Q2E-600H-
208V, Q2E-800-208/240V, Q2-500-120V, Q2-500-CUL20, Q2E-500-120V, Q2E-
500CUL20, Q2-600H-CE, Q2-600H-UK, R2E-800-208V
Q2-1200B-208/240V, R2-12BSZ-208/240V, R2-1200B-208/240V, R2E-12BK-208
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED
INCLUDE MODEL AND SERIAL NUMBER
PAGE
Some items are included for illustrative purposes only and in certain instances may not be available.
OF
1
5
24
PARTS LIST
January 26, 2015, Rev. G
Models:
Q2-500-120V, Q2E-500-120V, Q2-500-CUL20, Q2-600H-CE, Q2-600H-UK, Q2-600HF-208, Q2-600H-208/220/240V,
Q2-600HS-208, Q2E-600H-208/240V, Q2-800-208/220/240V, Q2-800-240UK, Q2-800-230CE, Q2E-800-208/240V,
Q2-1200B-208/240V, R2-12BSZ-208/240V, R2--1200-208/240V, R2-600HJ-208/240V, R2-800-208V
CONVEYOR TOASTERS
Fig No Part No.
Qty
12
2N-209100
2N-209112
2N-209114
2N-209193
2N-209194
2N-209198
2N-209199
2N-209216
2N-Z15500
2N-Z15500
2N-Z15987
Description
4 ELMT, METAL 120V 430W
ELMT, SERPENTINE, RCS
2
SERPENTINE ELMT RCS
ELEM METAL, 700W/240V
4
ELMT METAL, 200W/120V
ELMT METAL, 200W/104V
METAL ELMT, 500W, 104V
ELMT, METAL, 500W, 120V
6
ELMT METAL, 700W/104V
ELMT METAL, 470W/208V
ELMT METAL, 470W/240V
HO-197842 4 HEATERTUBE, QUARTZ
13
14
HD-198042 6 HEATERTUBE, QUARTZ
HG-198062 HEATERTUBE, QCS-2-1200B
HG-198064 HEATERTUBE, QCS-2-1200B
HO-197841
4
HEATERTUBE, QUARTZ
HO-197844
HC-Z10390
HC-Z10440
HC-Z10443
HC-Z11288
HB-Z10857
HC-Z10388
HEATERTUBE, QUARTZ
ELMT RETAINER, RIGHT QCS
1
ELMT RETAINER, RIGHT
HEATER TUBE RETAINER
2 RETAINER, RCS ELMT
ELMT GUIDE PLATE
HC-Z10439
HC-Z10442
HC-Z15540
2
ELMT GUIDE PLATE
ELMT GUIDE PLATE 1200
ELMT GUIDE PLATE SERP
PLATE - ELMT GUIDE
3
15 2E-Z10406 2 TERMINAL BLOCK 4 POS.
16 2E-Z9736
1
1 TERMINAL BLOCK - POWER
Application
R2E-500-120V
R2-12BSZ-240V, R2-1200B-240V, R2E-1200B240, R2E-12BK-240
R2-12BSZ-208V, R2-1200B-208V, R2E-1200B208, R2E-12BK-208
R2-600H-240V
R2-12BSZ-240V, R2-1200B-240V, R2E-1200B240, R2E-12BK-240
R2-12BSZ-208V, R2-1200B-208V, R2E-1200B208 R2E-12BK-208
R2-600HJ-208V, R2-600HJ-208, R2-60HCJ-208
R2-600HJ-240V, R2-60HCJ-240
R2-600H-208V, R2-800-208V, R2E-800-208V
R2-600HA-208, R2-800A-208V, R2E-800A-208
R2-600HA-240, R2-800A-240V, R2-60HC-240V, R2-60HC-CE, R2-80C-240V
Q2-600H-240V, Q2-800-240V, Q2E-600H-240V, Q2E-600H-240V, Q2-600H-UK, Q2-
800-240UK
Q2-500-120V, Q2-500KL-120, Q2E-500-120V, Q2E-500CUL20
Q2-1200B-208V, Q2-12BC-208
Q2-1200B-230CE/240V
Q2-600H-208V, Q2-800-208V, Q2E-600H-208V, Q2E-600H-208V, Q2E-800-208V, Q2-
500-120V, Q2-500-CUL20
Q2-600H-220V, Q2-800-220V, Q2E-600H-220V, Q2-600H-CE
Q2-600H-208/220/240V, Q2-800-208/220/240V, Q2E-600H-208V, Q2E-800-208/240V,
R2-600H, R2-800
Q2-1200B-208/240V
R2-12BSZ-208/240V, R2-1200B-208/240V, R2E-12BK-208
R2-600H, R2-600HJ, R2-800, R2E-500, R2E-800
Q2-500-120V, Q2-500-CUL20, Q2E-500-120V, Q2E-500CUL20
Q2-600H-208/220/240V, Q2-800-208/220/240V, Q2E-600H-208V, Q2E-800-208/240V,
Q2-600H-CE, Q2-600H-UK, R2-800, R2E-800
Q2-1200B-208/240V
R2-12BSZ-208/240V, R2-1200B-208/240V, R2E-1200B208, R2E-12BK-208
R2-600HA
R2E-800-208V
Q2E-300H-120, Q2E-500-120V, Q2E-500CUL20, Q2-600H-208/220/240V, Q2-800-
208/220/240V, Q2-1200B-208/240V, R2-12BSZ-208/240V, R2-1200B-208/240V, Q2-
500-120V, Q2-500-CUL20, Q2E-500-120V, Q2E-500CUL20, Q2-600H-CE, Q2-600H-
UK, R2E-500-120V, R2E-12BK-208
Q2E-600H-208/240V, Q2E-800-208/240V
Q2-600H-208/220/240V, Q2-800-208/220/240V, Q2-1200B-208/240V, R2-12BSZ-
208/240V, R2-1200B-208/240V, R2-600HJ-208/240V, Q2E-600H-208V, Q2E-800-
208/240, Q2-500-120V, Q2-600H-CE, Q2-600H-UK
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED
INCLUDE MODEL AND SERIAL NUMBER
PAGE
Some items are included for illustrative purposes only and in certain instances may not be available.
OF
2
5
25
PARTS LIST
January 26, 2015, Rev. G
Models:
Q2-500-120V, Q2E-500-120V, Q2-500-CUL20, Q2-600H-CE, Q2-600H-UK, Q2-600HF-208, Q2-600H-208/220/240V,
Q2-600HS-208, Q2E-600H-208/240V, Q2-800-208/220/240V, Q2-800-240UK, Q2-800-230CE, Q2E-800-208/240V,
Q2-1200B-208/240V, R2-12BSZ-208/240V, R2--1200-208/240V, R2-600HJ-208/240V, R2-800-208V
CONVEYOR TOASTERS
Fig No
17
20
21
22
23
24
25
26
27
28
Part No.
2K-200464
18 2E-200566
19 2R-200562
HA-120239
HB-120261
2P-402728
2J-200538
2J-200539
2E-200551
2R-200709
2M-200864
2M-200894
2M-201810
2M-201813
2M-Z13358
2M-Z13864
2M-Z14858
2R-200768
2R-200769
2R-200708
HA-100560
HF-100562
29 PS-200787
Qty
2
BUSHING WIRE RING 7/8”
1
1 SWITCH, RESET
1 FAN GUARD
SPEED CONTROL ASSEMBLY
1
SPEED CONTROL ASSY 500
1
2
1
Description
POT, ANTI SPIN PLATE
SWITCH, EGO 240V INFINITE
SWITCH, EGO 120V INFINITE
SWITCH ROTARY
Application
Q2-600H-208/220/240V, Q2-800-208/220/240V, Q2E-600H-208V, Q2E-800-208/240V,
Q2-500-120V, Q2-500-CUL20, Q2E-500-120V, Q2E-500CUL20, Q2-600H-CE, Q2-
600H-UK
Q2-1200B-208/240V, R2-12BSZ-208/240V, R2-1200B-208/240V, R2-600HJ-208/240V
ALL
ALL
Q2-500-120V, Q2-500-CUL20
Q2-600H-208/220/240V, Q2-800-208/220/240V, Q2-600H-CE, Q2-600H-UK, R2-
600HJ-208/240V, R2-800-208V, Q2-1200B-208/240V, R2-12BSZ-208/240V, R2-
1200B-208/240V
ALL NON-ELECTRONIC
Q2-600H-208/220/240V, Q2-800-208/220/240V, Q2-1200B-208/240V, R2-12BSZ-
208/240V, R2-1200B-208/240V, R2-600HJ-208/240V, Q2-500-120V,
Q2-500-120V, Q2-500KL-120, Q2-500-CUL20
Q2-600H-208/220/240V, Q2-800-208/220/240V, Q2-1200B-208/240V, R2-12BSZ-
208/240V, R2-1200B-208/240V, R2-600HJ-208/240V, Q2-500-120V, Q2-500-CUL20
4 LEG 1” CHOME PLASTIC
LABEL, QCS-2 & 3 CONTROLS
LABEL, QCS-2&3 BAGEL CONT
Q2-600H-208/220/240V, Q2-800-208/220/240V, Q2-1200B-208/240V, R2-12BSZ-
208/240V, R2-1200B-208/240V, R2-600HJ-208/240V, Q2E-600H-208V
Q2-600H-208/220/240V, Q2-800-208/220/240V, Q2-500-120V, Q2-500-CUL20, Q2-
600H-CE, Q2-600H-UK
Q2-1200B-208/240V
1
LABEL, RCS-2&3 BAGEL CONT R2-12BSZ-208/240V, R2-1200B-208/240V, R2-600HJ-208/240V, R2-800-208V
1
3
LABEL, QCSE
LABEL - CONTROL Q2E-600HW
LABEL - CONTROL PANEL R2E
LABEL - CONTROL R2E-12BK
KNOB, CNTRL Q SERIES, SPEED
KNOB, POWERSAVER Q SERIES
Q2E-600H-208V, Q2E-500-120V, Q2E-500CUL20
Q2E-600HW, R2E-12BFCF208
R2E-500-120V, R2E-800-208V, R2E-1200B208
R2E-12BK-208
Q2-600H-208/220/240V, Q2-800-208/220/240V, Q2-500-120V, Q2-500-CUL20, Q2-
600H-CE, Q2-600H-UK
Q2-600H-208/220/240V, Q2-800-208/220/240V, R2-600HJ-208V, Q2-500-120V, Q2-
600H-CE, Q2-600H-UK
1 KNOB, POWERSAVER Q SERIES Q2-1200B-208/240V, R2-12BSZ-208/240V, R2-1200B-208/240V, R2-600HJ-208/240V
4
2
1
1
KNOB, CONTROL CAP
KNOB, CONTROL CAP
TRAY, PULL OUT QCS, 10”
SECURITY TRAY, PULL OUT
QCS 1&2 CRUMB TRAY GUARD w/HRD
Q2-600H-208/220/240V, Q2-800-208/220/240V, R2-600HJ-208/240V, Q2-500-120V,
Q2-500-CUL20, Q2-600H-CE, Q2-600H-UK
R2-12BSZ-208/240V, R2-1200B-208/240V
ALL
ALL SECURUITY UNITS
ALL
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED
INCLUDE MODEL AND SERIAL NUMBER
PAGE
Some items are included for illustrative purposes only and in certain instances may not be available.
OF
3
5
26
PARTS LIST
January 26, 2015, Rev. G
Models:
Q2-500-120V, Q2E-500-120V, Q2-500-CUL20, Q2-600H-CE, Q2-600H-UK, Q2-600HF-208, Q2-600H-208/220/240V,
Q2-600HS-208, Q2E-600H-208/240V, Q2-800-208/220/240V, Q2-800-240UK, Q2-800-230CE, Q2E-800-208/240V,
Q2-1200B-208/240V, R2-12BSZ-208/240V, R2--1200-208/240V, R2-600HJ-208/240V, R2-800-208V
CONVEYOR TOASTERS
Fig No Part No.
Qty Description Application
30
HC-402457
HF-100656
HB-120309
HB-120311
31 2B-200763
32
HF-101115
PS-120316
33 2B-Z10675
1
CRUMB TRAY, QCS-2
SECURITY CRUMB TRAY, QCS
ALL
Q2-600HS-208
CRUMB TRAY ASSY, Q2E-600HW Q2E-600HW-208, 240
CRUMB TRAY ASSY R2E-12BK
1 LOADUP, 10 EURO, WIRE
1
TRAY, CRUMB TRAY ASSEMBLY
CRUMB TRAY ASSY COMPLETE
CERTAIN MODELS
CERTAIN MODELS
R2E-12BK
2 MASTERLINK 10” CONV ALL
34 SP-160027
35 2A-202904
36 2P-200700
37 2P-200736
1
1
2
2
BELT, CONVEYOR 10”
SHAFT, 210HX IDLER
SPRING LOAD BEARING PTFE
2” INCH BEARING SPRING
38 HC-402134 1 NC10H SHUTTER ROD
39 HC-402206 1 HEAT SHUTTER, SWINGING
ALL
ALL
ALL
ALL
Q2-600H-208/220/240V, R2-600HJ-208V/240V, Q2E-600H-208V
Q2-600H-208/220/240V, R2-600HJ-208V/240V, Q2E-600H-208V
40
HC-Z10389
1
ELMT RETAINER, LEFT QCS
Q2-600H-208/220/240V, Q2-800-208/220/240V, Q2E-600H-208V, Q2E-800-208/240V,
Q2-500-120V, Q2-500-CUL20, Q2E-500-120V, Q2E-500CUL20, Q2-600H-CE, R2-
600H, R2-800
41
42
HC-Z10441
2A-200284
2E-200574
2U-200591
1
1
ELMT RETAINER, LEFT QCS
E-CLIP 5/16”
SWITCH, FAN CERAMIC
QCSE CONTROL BOARD
Q2-1200B-208/240V
ALL
Q2-1200B-208/240V, R2-12BSZ-208/240V, R2-1200B-208/240V
Q2E-300H, Q2E-500,Q2E-600H-208/240V, Q2E-800-208/240V, Q2E-500-120V, R2-
800-208V, R2E-500-120V, R2E-1200B208, R2E-800A-208
43
2E-Z13360
2E-Z14864
HC-Z18132
1
CONTROL BOARD Q2E-600HW
CONTROL BOARD R2E-12BK
Q2E-600HW
R2E-12BK-208/240
CNTROL BOARD PROGRAMMED R2E-12BCF208
Q2E-300H, Q2E-500, Q2E-600H-208/240V, Q2E-800-208/240V, Q2E-500-120V, R2E-
800A-208, R2E-12BK-208/240
44
2U-200592 1 QCSE POWER BOARD
HD-Z13861 1 POWER BOARD 120V
45 HF-402536 1 SECURITY LOCKING COVER
46
2R-200752
HA-Z11222
47 2E-Z17514
2K-200463
2K-Y6764
1
1
1
KEYLOCKING SPEC KEYED
KEYLOCK - DRILLED
SENSOR, SPEED
BUSHING CORD HEYCO 1247
BUSHING CORD 12/3 BL
NI
2K-Y2968
1
BUSHING - HEYCO 7W-2
R2E-500-120V
ALL SECURUITY UNITS
ALL SECURUITY UNITS
Q2-600HS-208
R2E-12BCF208
Q2-600H-208/220/240V, Q2-800-208/220/240V, R2-600HJ-208V
Q2-1200B-208/240V, R2-12BSZ-208/240V, R2-1200B-208/240V
Q2E-600H-208/240V, Q2E-800-208/240V, Q2E-500-120V, R2-800-208V, R2E-500-
120V, R2E-12BK-208
2K-200465
NI 2P-200786 1
BSHNG, CORD 14/3 BL
WIRE BRUSH
NI D9-GR0216 1 POWER CORD ASSY-UK
Q2-12B-230-CE
R2-1200B-208V
Q2-800-240UK
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED
INCLUDE MODEL AND SERIAL NUMBER
PAGE
Some items are included for illustrative purposes only and in certain instances may not be available.
OF
4
5
27
PARTS LIST
January 26, 2015, Rev. G
Models:
Q2-500-120V, Q2E-500-120V, Q2-500-CUL20, Q2-600H-CE, Q2-600H-UK, Q2-600HF-208, Q2-600H-208/220/240V,
Q2-600HS-208, Q2E-600H-208/240V, Q2-800-208/220/240V, Q2-800-240UK, Q2-800-230CE, Q2E-800-208/240V,
Q2-1200B-208/240V, R2-12BSZ-208/240V, R2-1200-208/240V, R2-600HJ-208/240V, R2-800-208V
CONVEYOR TOASTERS
Fig No Part No.
Qty Description
NI
2E-200375
2E-Y7874
2E-Z13364
HA-120241
HA-120242
HB-120267
2E-200372
HB-120268
HA-120245
HB-120274
1
CORD SET, 14/3 120V EZ10
CORD SET CEE7/VII 6’-6”
CORD SET 14GA. 6-20P 80”
CORD SET ASSEMBLY QCS-1
CORDSET ASSY QCS-1-CUL20
CORD SET R2-1200B
CORD SET, 12/3 CORD
CORD SET ASSY R2-12BSZ
CORD ASSY NEMA 6-20P
CORD ASSY 6-20 QCSE
HB-120276 CORD ASSEMBLY CEE7-7
HD-140078 CORD SET, QCSE 2, 120V
HB-120274 CORD SET ASSY, 6-20 QCSE
NI HG-402144 1 FAN SWITCH BRACKET
Application
Q2E-300H-120, Q2E-30HC-120, Q2E-500-120, Q2E-50C-120, R2E-500-120V, R2E-
50C-120
Q2-12B-230-CE
Q2E-600HW208, Q2E-600HW240
Q2-500-120V
Q2-500-CUL20
Q2-600H-220V
R2-1200B-208/240V, R2-120BC-208/240
R2-12BSZ-208/240V, R2-1200B-208/240V
Q2-600H-208/240V, Q2-800-208/220V, Q2-1200B-208V, R2-600HJ-208/240V,
R2-60HC-CE
Q2E-600H-208/240V, Q2E-800-208/240V
Q2-600H-CE, Q2-60HC-CE, Q2-800-230CE, Q2-80C-230CE, Q2E-600H-CE,
Q2E-60HC-CE, Q2E-800-CE, Q2E-810C-CE, R2-60HC-CE
Q2E-500CUL20
R2E-12BK-208/240
R2-12BSZ-208/240V, R2-1200B-208V
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED
INCLUDE MODEL AND SERIAL NUMBER
PAGE
Some items are included for illustrative purposes only and in certain instances may not be available.
OF
5
5
28
7
8
5
6
9
10
Part No.
HC-120283
HC-120284
HC-120285
2R-Z8879
HA-120243
HB-120262
HC-120289
HI-115071
2U-200561
HC-Z11212
2A-202902
HA-112261
2P-Z8779
2P-150013
2P-150015
2P-200645
2P-200648
GB-197847
HL-197862
HL-197863
HT-197845
PARTS LIST
January 26, 2015, Rev. G
Models:
Q3-950H-208/220/240V/CE/UK, Q3-1000-208/220/240/CE/UK, Q3-1300-208/240V, Q3-1400BH-208/240/CE,
Q3-1600B-208/240, Q3E-950H-208/240, Q3E-1000-208/240, Q3E-1300-208/240
CONVEYOR TOASTERS
Fig No
1
2
3
4
11
12
13
HT-197846
2N-209130
2N-209160
2N-209131
2N-209132
GB-197847
HH-198053
HJ-198054
HJ-198060
HK-198066
HT-197860
HC-Z10390
HC-Z11287
HC-Z10440
HC-Z11288
HC-Z19065
Qty
1
Description
1 CHASSIS ENCLOSURE ASSY
ASSY, AIR BAFFLE QCS-3 LO
ASSY, AIR BAFFLE QCS-3 HI
1 2-5/8 DIA FAN BLACK CW
MTR,ASSY,QCS,220,230,240V
1
MOTOR ASSY 208-240V
MOTOR ASSEMBLY QCS3
MOTOR, RMS72, W/TERMINALS
1 MOTOR,FAN240V 23BTM
1 BACK PANEL,QCS-3
1 SHAFT, T714 DRIVE
2 BEARING ASSY, 5/16 BRONZE
1 SPROCKET 25P-11T .313 ID
Application
ALL
Q3-1000, -1300/S, -1600B, Q3E-1000, -1300, R3-1000
Q3-950H, -95WS, -1400BH, R3-950H
OLDER MODEL UNITS
Q3-950H-CE, Q3-1000-CE, Q3-1000-UK, Q3-1400BH-CE
Q3-950H, Q3-1000, Q3-1300-240V, Q3-1300S-240, Q3-1400BH, Q3-
1600B
Q3-1300-208V, Q3-1300S-208V, R3-1300-208V
Q3E-1300-208/240V
ALL
ALL
ALL
Q3-950H, Q3-1000, Q3-1300, Q3-1400BH,
ALL
1
1
4
6
1
DRIVE CHAIN #25 ROLLER
HEATERTUBE, QUARTZ, 208V
Q3-950H-208/220/240V, Q3-1000, Q3-1300, R3E-14CAR
CHAIN DRIVE #25 ROLLER 20.5” LN Q3-1600B-208, R2-1200B, R2-12BSZ, R2E-12BK
SPROCKET, 25B17 X 5/16 Q3-950H, Q3-1000, Q3-1400BH
SPROCKET, 25B32 X 5/16
HEATERTUBE, QUARTZ, 240V
Q3-1600B, R3E-14CAR
Q3-950H-240V, Q3-1000-240V, Q3E-950H-240V, Q3E-1000-240V
HEATERTUBE, QCS-3-1600B
HEATERTUBE, QUARTZ
Q3-1600B-208
Q3-1600B-240
Q3-950H-208V, Q3-1000-208V, Q3E-1000-208V, Q3E-950H-208V,
Q3E-95WS-208
HEATERTUBE, QUARTZ, 220V
ELEMENT, METAL 208V 800W
ELEMENT, METAL 240V 800W
ELEMENT, METAL 208V 600W
ELEMENT, METAL 240V 600W
HEATERTUBE, QUARTZ, 240V
HEATERTUBE, QUARTZ
HEATERTUBE, QCS-3-1300
HEATERTUBE, QCS-3-1300
HEATERTUBE, QCS-3-1400BH
HEATERTUBE, QUARTZ
ELEMENT RETAINER,RHT,QCS-
ELEMENT REATINER-RH, RCS-2
ELEMENT RETAINER, RIGHT
2
RETAINER, RCS, ELEMENT
3
BRACKET-ELEMENT RETAINER
Q3-950H-220V, Q3-950H-CE, Q3-1000-220V, Q3-1000-CE, Q3-1000-
UK
R3-950H-208V, R3-1000-208V, R3E-14CAR208
R3-950H-CE, R3E-14CAR240
R3-1300-208V
R3-1300-240V
Q3-1400BH240
Q3-13-220V
Q3-1300-240V, Q3E-1300-240V
Q3-1300-208V, Q3E-1300-208V
Q3-1400BH208
Q3-1400BH-CE
Q3-950H, Q3-1000, Q3E-950H, Q3E-1000, Q3E-1300
R3-950H-208V, R3-950H-CE
Q3-1400BH, Q3-1600B
R3-1000-208V, R3-950H-208V, R3-950H-CE
R3E-14CAR
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED
INCLUDE MODEL AND SERIAL NUMBER
PAGE
Some items are included for illustrative purposes only and in certain instances may not be available.
OF
1
3
29
PARTS LIST
January 26, 2015, Rev. G
Models:
Q3-950H-208/220/240V/CE/UK, Q3-1000-208/220/240/CE/UK, Q3-1300-208/240V, Q3-1400BH-208/240/CE,
Q3-1600B-208/240, Q3E-950H-208/240, Q3E-1000-208/240, Q3E-1300-208/240
CONVEYOR TOASTERS
30
35
36
37
38
31
32
33
34
39
28
29
18
19
20
21
22
23
24
15
16
17
Part No.
HB-Z10858
HC-Z10388
HC-Z19063
HC-Z10439
HC-Z14977
2E-Z10406
2E-Z9736
2K-200464
2E-200566
2R-200562
HB-120261
HC-120278
2P-402728
2J-200538
2E-200551
2R-200709
HP-402209
2M-200864
2M-201813
2M-200899
2M-Z13358
2R-200768
2R-200769
Fig No
14
25
26
27
40
2R-200708
HH-100561
HI-100563
PS-200788
HC-Z11261
HI-100566
2B-200764
HI-101116
2B-200603
SP-160028
2A-202905
2P-200700
2P-200736
HH-402135
HH-401698
HC-Z10389
HC-Z11288
HC-Z10441
Qty Description
2
ELEMENT GUIDE PLATE QCS2
ELEMENT GUIDE PLATE
ELEMENT GUIDE PLATE
ELEMENT GUIDE PLATE 1200
ELEMENT GUIDE PLATE
2 TERMINAL BLOCK 4 POS
1 TERMINAL BLOCK - POWER
1
2
BUSHING, WIRE RING 7/8”
1 SWITCH, RESET, 0796
1 FAN GUARD
1
SPEED CONTROL ASSY 500
SPEED CONTROL ASSEMBLY
1 POT, ANTI SPIN PLATE
2 SWITCH, EGO 240V INFINITE
1 SWITCH ROTARY
4
LEG 1 INCH CHROME PLASTIC
BRACKET, SECURITY LEG TT
1
LABEL, QCS-2 & 3 CONTROL
LABEL, QCSE
LABEL, RCS-2, RCS-3 CONTR
LABEL CONTROL
1 KNOB, CONTROL Q SERIES
1 KNOB, POWERSAVER Q SERIES
3 KNOB, POWERSAVER Q SERIES
2
4
KNOB, CONTROL CAP
1
TRAY, PULL OUT, QCS, 14
SECURITY PULL OUT TRAY
1 QCS-3 CRUMB TRAY GRD w/HRD
1
CRUMB TRAY,QCS3
SECURITY CRUMB TRAY, QCS
1 LOADUP, 14 EURO, WIRE
1 TRAY, CRUMB ASSEMBLY
3 BELT LINK 14IN SPACECLIP
1 CONVEYOR BELT (14” X 35”)
1 SHAFT, 214HX IDLER
2 BEARING-PTFE SPRING LOAD
2 2 INCH BEARING SPRING
1 NC14H SHUTTER ROD
1 HEAT SHUTTER, SWINGING
1 ELEMENT RETAINER,LFT,QCS-
2 RETAINER, RCS, ELEMENT
1 ELEMENT RETAINER, LEFT
Application
Q3-950H
Q3-1000, Q3-1300, Q3E-1000, Q3E-950H-208
R3E-14CAR
Q3-1400BH, Q3-1600B
Q3E-95WS
Q3-950H, Q3-1000, Q3-1300, Q3-1600B,
Q3-950H, Q3-1000, Q3-1300, Q3-1600B,
Q3-1400BH
Q3-950H, Q3-1000
ALL
ALL
Q3-950H, Q3-1000, Q3-1300-240V, Q3-1600B
Q3-1300-208V, Q3-1400BH, R3-1300-208V
ALL
Q3-950H, Q3-1000, Q3-1300, Q3-1400BH
ALL
Q3-950H, Q3-1000, Q3-1300, Q3-1400BG, Q3-1600B
Q3-950HS-208
Q3-950H, Q3-1000, Q3-1300, Q3-1400BG, Q3-1600B, R
Q3E-950H, Q3E-1000, Q3E-1300
R3-950H, R3-1000
R3E-14CAR
Q3-950H, Q3-1000, Q3-1300, Q3-1400BH, Q3-1600B
Q3-1600B
Q3-950H, Q3-1000, Q3-1300, Q3-1400BH
Q3-1600B
Q3-950H, Q3-1000, Q3-1300, Q3-1400BH
ALL
Q3-950HS-208
ALL
Q3-950H, Q3-1000, Q3-1300, Q3-1400BG, Q3-1600B
Q3-950HS-208, Q3-1300S-208/240
ALL EXCEPT R2E-12BK
Q3-950H, Q3-1000, Q3-1300, Q3-1400BG, Q3-1600B
ALL
ALL
ALL
ALL
ALL
Q3-950H, Q3-1400BH, Q3E-950H
Q3-950H, Q3-1400BH
Q3-950H, Q3-1000, Q3-1300, Q3E-950H, Q3E-1000, Q3E-1300
R3-950H
Q3-1400BH, Q3-1600B
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED
INCLUDE MODEL AND SERIAL NUMBER
PAGE
Some items are included for illustrative purposes only and in certain instances may not be available.
OF
2
3
30
PARTS LIST
January 26, 2015, Rev. G
Models:
Q3-950H-208/220/240V/CE/UK, Q3-1000-208/220/240/CE/UK, Q3-1300-208/240V, Q3-1400BH-208/240/CE,
Q3-1600B-208/240, Q3E-950H-208/240, Q3E-1000-208/240, Q3E-1300-208/240
CONVEYOR TOASTERS
44
45
NI
NI
NI
NI
NI
NI
46
47
NI
NI
NI
NI
NI
Fig No
41
42
43
Part No.
2A-200284
2E-200574
2U-200591
HC-Z13815
HC-Z18132
2U-200592
HB-Z11456
2R-200752
2E-Z17514
2E-Z5680
2E-Z5681
2K-Y6764
2K-Y2968
2P-200786
HB-120245
HB-120272
HB-120276
HG-402144
Qty Description Application
1 E-CLIP 5/16
1 SWITCH, FAN, CERAMIC
1
QCSE CONTROL BOARD
CONTROL - PROGRAMMED
CONTROL - PROGRAMMED
1 QCSE POWER BOARD
1 SECURITY LOCKING COVER
ALL
Q3-1600B
ALL Q2E & Q3E
Q3E-950HP208, CUSTOMER SPECIFIC
R3E-14CAR
Q3E, R3E-14CAR
Q3-950HS-208, Q3-1300S-208/240, 9H-Q2-3KL-KIT
2
4
1 KEYLOCKING SPEC KEYED ALIKE Q3-950HS-208, Q3-1300S-208/240, 9H-Q2-3KL-KIT
1 SENSOR, SPEED R3E-14CAR
FUSE, 5A - CLASS G
Q3-1300-208V, Q3-1400BH, R3-1300-208V
Q3E-1300-208/240V, R3E-14CAR
1
2
FUSEHOLDER, CLASS G
1 BUSHING,CORD HEYCO 12/3 BL
1 BUSHING - HEYCO
Q3-1300-208V, Q3-1400BH, R3-1300-208V
Q3E-1300-208/240V, R3E-14CAR
Q3-950H, Q3-1400BH208
Q3-950H-CE, Q3-1400BH-CE
1 WIRE BRUSH
1 CORD ASSY NEMA 6-20P
1 ASSY, CORD SET, 6-30P
1 CORD ASSEMBLY CEE7-7
1 FAN SWITCH BRACKET
ACCESSORY
Q3-950H-208/220/240V
Q3-1300-208V, Q3-1400BH208, Q3-1600B-208, R3-1300-208V
Q3-950H-CE, Q3-1000-CE, Q3-1400BH-CE
Q3-1600B
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED
INCLUDE MODEL AND SERIAL NUMBER
PAGE
Some items are included for illustrative purposes only and in certain instances may not be available.
OF
3
3
31
STAR INTERNATIONAL HOLDINGS INC. COMPANY
Star - Holman - Lang - Wells - Bloomfield - Toastmaster
10 Sunnen Drive, St. Louis, MO 63143 U.S.A.
(314) 678-6303 www.star-mfg.com
Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Conveyor Belt Toaster
- Heating Element
- Crumb Tray
- Power Saver Switch
- Programmable Settings
- Safety Features
- Easy Maintenance
