BOTTOM FREEZER
REFRIGERATOR
User’s Guide
Please read this guide thoroughly before operating and
keep it handy for reference at all times.
CONGÉLATEUR
INFÉRIEUR
RÉFRIGÉRATEUR
Guide d’Utilisation et
d’Entretien
Veuillez lire ce manuel en entier avant de mettre en
marche l'unité et conservez-le à portée de la main pour
le consulter à tout moment.
P/No. MFL37933574
TABLE OF CONTENTS
Safety Instructions
3–9
Dairy Bin
24
Parts and Features
10
Utility Bin
24
Refrigerator Installation
❿ Freezer section
11–18
Unpacking Your Refrigerator
11
Tilting Door
24
Installation
11
Ice Bin
24
Base Cover
11
Tilt-Out Door Basket
25
Durabase
25
Durabase Divider
25
Pull out Drawer
25
Filter
26
Removing and Replacing
Your Refrigerator Handles
and Doors
12–17
Leveling and Door Alignment
Using Your Refrigerator
18
19–26
Care and Cleaning
27–28
Ensuring Proper Air Circulation
19
Multi-Flow
19
General Cleaning Tips
27
Setting the Controls
19
Outside
27
Adjusting Control Settings
20
Inside Walls
27
Food Storage Guide
20
Door Liner and Gaskets
27
Storing Frozen Food
21
Plastic Parts
27
Condenser Coils
27
❿ Refrigerator section
Water Dispenser
21
Light Bulb Replacement
Refrigerator Shelves
22
Power Interruptions
28
Bottle Holder
22
When you go on vacation
28
Crisper Humidity Control
23
When you move
28
Removing Crisper
23
About the Automatic Icemaker
Glide ‘N’ Serve
23
Connecting the Water Line
30-32
Modular Door Bin
24
Troubleshooting Guide
33–36
2
27–28
29
SAFETY MESSAGES
BASIC SAFETY PRECAUTIONS
This guide contains many important safety messages. Always read and obey all safety messages.
This is the safety alert symbol. It alerts you to safety messages that inform you
of hazards that can kill or hurt you or others, or cause damage to the product.
All safety messages will be preceded by the safety alert symbol and the hazard signal word
DANGER, WARNING, CAUTION. These words mean:
DANGER
WARNING
CAUTION
You will be killed or seriously injured if you don’t follow instructions.
You can be killed or seriously injured if you don’t follow instructions.
Indicates an imminently hazardous situation which, if not avoided,
may result in minor or moderate injury, or product damage only.
All safety messages will identify the hazard, tell you how to reduce the chance of injury, and tell you
what can happen if the instructions are not followed.
w DANGER: RISK OF CHILD ENTRAPMENT
Child entrapment and suffocation are not
problems of the past. Junked or abandoned
refrigerators are still dangerous…even if they will
sit for just a few days. If you are getting rid of
your old refrigerator, please follow the
instructions at right to help prevent accidents.
BEFORE YOU THROW
AWAY YOUR OLD
REFRIGERATOR OR
FREEZER
• Take off the doors.
• Leave the shelves in place so
that children may not easily climb
inside.
CFC DISPOSAL
Your old refrigerator may have a cooling system
that used CFCs (chlorofluorocarbons). CFCs are
believed to harm stratospheric ozone.
If you are throwing away your old refrigerator,
make sure the CFC refrigerant is removed for
proper disposal by a qualified servicer. If you
intentionally release this CFC refrigerant, you can
be subject to fines and imprisonment under
provisions of environmental legislation.
3
GROUNDING REQUIREMENTS
Use a receptacle which cannot be turned off with
a switch or pull chain. Do not use an extension
cord.
Where a standard two-prong wall outlet is
encountered, it is your personal responsibility and
obligation to have it replaced with a properly
grounded three-prong wall outlet.
Do not, under any circumstances, cut or
remove the third (ground) prong from the
power cord.
NOTE: Before performing any type of installation,
cleaning,or removing a light bulb, turn the control
(Thermostat, Refrigerator Control or Freezer
Control, depending on the model)to OFF and
then disconnect the refrigerator from the electrical
source. When you are finished,reconnect the
refrigerator to the electrical source and reset the
control (Thermostat, Refrigerator Control or
Freezer Control, depending on the model) to the
desired setting.
IMPORTANT: Please read carefully.
TO CONNECT ELECTRICITY
w WARNING
Electrical Shock Hazard
FOR PERSONAL SAFETY, this appliance
must be properly grounded. Have the wall
outlet and the circuit checked by a qualified
electrician to make sure the outlet is properly
grounded.
RECOMMENDED GROUNDING
METHOD
The refrigerator should always be plugged into its
own individual properly grounded electrical outlet
rated for 220 Volts, 50 Hz, AC only, and fused at
15 amperes.
This provides the best performance and also
prevents overloading house wiring circuits which
could cause a fire hazard from overheated wires.
It is recommended that a separate circuit serving
only this appliance be provided.
w WARNING
• Repair or replace immediately all electric
service cords that have become frayed or
otherwise damaged. Do not use a cord that
shows cracks or abrasion damage along its
length or at either the plug or connector end.
• When moving your refrigerator away from the
wall, be careful not to roll over or damage the
power cord.
• Keep fingers out of pinch point areas;
clearances between the doors and cabinet are
necessarily small. Be careful closing doors
when children are in the area.
• This refrigerator must be properly installed in
accordance with the Attention Installer
Instructions that were taped to the front of the
refrigerator.
• Don’t touch the lamp, in case of light on the long
time, Because it can be very hot.
• DO NOT refreeze frozen foods which have
thawed completely. The United States
Department of Agriculture in Home and Garden
Bulletin No. 69 says:
…You may safely refreeze frozen foods that
have thawed if they still contain ice crystals or if
they are still cold—below 4°C.
…Thawed ground meats, poultry or fish that
have any off-odor or off-color should not be
refrozen and should not be eaten. Thawed ice
cream should be discarded. If the odor or color
of any food is poor or questionable, get rid of it.
The food may be dangerous to eat.
Even partial thawing and refreezing reduces the
eating quality of foods, particularly fruits,
vegetables and prepared foods. The eating
quality of red meats is affected less than that of
many other foods. Use refrozen foods as soon
as possible to save as much of their quality as
you can.
SAVE THESE INSTRUCTIONS
4
IMPORTANT SAFETY INSTRUCTIONS
Don’t use an extension cord
• If water pressure does not reach the rating
147 kPa (1.5 kgf/cm2) or below, it is necessary to
purchase a separate pressure pump for normal
automatic icing and cool water feed.
• Keep the total length of the feed water pipe tube within
8 m and be careful for the tube not be bent. If the tube
is 8 m or longer it may cause trouble in water feed
owing to the drain water pressure.
If possible, connect the refrigerator to its own
individual electrical outlet to prevent it and other
appliances or household lights from causing an
overload that could cause a power outage.
Accessibility of Supply Plug
The refrigerator-freezer should be so positioned that
the supply plug is accessible for quick disconnection
when accident happens.
• Install the feed water pipe tube at a place free from
heat.
Supply Cord Replacement
w WARNING
If the supply cord is damaged, it must be replaced
by the manufacturer or its service agent or a
similarly qualified person in order to avoid a hazard.
• Connect to potable water supply only.
• Refer to instructions with water filter kit for installation.
w WARNING
• The refrigerant and insulation blowing gas used in the
appliance require special disposal procedures. When
disposal, please consult with service agent or a
similarly qualified person.
FEED WATER PIPE INSTALLATION
Before installation
• Automatic ice maker can be installed only by
manufacturer.
• Automatic ice maker operation needs water pressure
of 147~834 kPa (1.5~8.5 kgf/cm2) (That is, an instant
paper cup (180 cc) will be fully filled within 3 sec.).
w WARNING
• Please do not use a dishwasher to clean the lower
drawers; the high temperature may cause damage to
the baskets which make them unusable.
w WARNING
To reduce the risk of fire, electric shock, or injury to persons when using your product,
basic safety precautions should be followed, including the following.
Read all instructions before using this appliance.
1. When connecting the power
The dedicated outlet should be used.
Do not allow the power plug to face upward
or to be squeezed at the back of the
refrigerator.
• Using several devices at one outlet may cause fire.
• The electric leakage
breaker may damage food
and the dispenser may be
leaked.
Water may be flown into or
the plug may be damaged,
which causes fire or
electric shock.
Prevent the power cord from being squeezed
or imprinted if the refrigerator is pushed in
after the power plug is extracted during the
installation.
When moving your appliance away from the
wall, be careful not to roll over the power cord
or to damage it in any way.
It becomes the cause of fire or electric shock.
Do not allow the power cord bent or pressed
by the heavy object to
be damaged.
It may damage the power
cord to cause fire or
electric shock.
5
w WARNING
Do not extend or modify the length of the
power plug.
Unplug the power plug when cleaning,
handling or replacing the interior lamp of the
refrigerator.
It causes electric shock or fire by
the electric damage of the power
cord or others.
• It may cause electric shock or injury.
• When replacing the interior
lamp of the refrigerator,
make sure that the rubber
ring for preventing the
electric spark within the
socket is not taken off.
Do not pull out the cord or touch the power
plug with wet hands.
Remove water or dust from the power plug
and insert it with the ends of the pins
securely connected.
It may cause electric shock or
injury.
Dust, water or unstable
connection may fire or
electric shock.
Unplug the power cord from the power
outlet for cleaning or other requirements.
It may cause electric shock or injury.
Pull out the power plug
not by grasping
the cord but the plug of
its end.
It may cause electric shock or
short circuit to fire.
Be sure to use grounded exclusive proper
voltage consent for the power plug.
Make sure of grounding.
Consult a qualified electrician or service
person if the grounding instructions are not
completely understood, or if you have
doubts on whether
the appliance is
properly grounded.
The incorrect grounding
may cause breakdown
and electric shock.
Be sure to use grounded extension consents
when extension consents are used.
It becomes the cause of fire.
Grounding
Conductor
Copper
flat
More than
75cm
When the power cord or the power plug is
damaged or the holes of
the outlet are loosed, do
not use them.
Wait for 5 minutes or
longer when
reconnecting the plug.
It may cause the operation of
the freezer to fail.
It may cause electric shock or
short circuit to make fire.
6
IMPORTANT SAFETY INSTRUCTIONS
2. When using the refrigerator
Do not place the heavy object or the
dangerous object
(container with liquid) on
the refrigerator.
Do not install the refrigerator in the wet
place or the place which
water or rain splashes.
Deterioration of insulation of
electric parts may cause
electric leakage.
It may be dropped to cause injury,
fire or electric shock when
opening or closing the door.
Do not cling to the door or the shelves of the
door or the home bar of the freezer or the
cool chamber.
Prevent children from entering the product.
It may endanger the life of
a child if the child enters
the refrigerator.
It may make the refrigerator
fallen down or damage the
hands. Especially, do not
allow the children to do the
above.
Opening and closing the door of the
refrigerator vigorously may cause the stored
food in the refrigerator basket to fall by
shock and hurt the foot, so take precautions.
Do not use or store inflammable materials
ether, benzene, alcohol, medicine, LP gas,
spray or cosmetics
near or in the
refrigerator.
Ether
Do not store the medicine or the academic
materials at the refrigerator.
When the material with
the strict temperature
control is stored, it may be
deteriorated or it may
make an unexpected
reaction to cause any risk.
The Academic
Medicine
dicine
The Me
Do not use the combustible spray near the
refrigerator.
Install in places away from the fire such as
the place where flammable gas is leaked.
It may cause fire.
It may cause fire.
7
Thinner
Do not use drier to dry the inside, nor light a
candle to remove odor.
It may cause explosion or
fire.
Benzene
It may cause explosion
or fire.
IMPORTANT SAFETY INSTRUCTIONS
Do not place flower vase, cup,
cosmetics, medicine or any
container with water on the
refrigerator.
In case of thunder and lightning, or not in
use for a long period of
time, detach the power
plug.
There is a danger of
electric shock or fire.
It may cause fire, electric shock or
injury by dropping down.
Use the submerged
refrigerator after
checking it.
Do not spray water at the outside or the
inside of the refrigerator or
do not clean it with benzene
or thinner.
Deterioration of insulation of
electric parts may cause electric
shock or fire.
When any strange smell or smoke is
detected from the refrigerator, power plug
get rid of electric
Service
outlet immediately
center
and contact to the
service center.
Thinner
It may cause electric shock
or fire.
Do not allow any person except the qualified
engineer to disassemble, repair or alter the
refrigerator.
It may cause injury,
electric shock or fire.
It may cause fire.
Do not use the refrigerator for non-domestic
purpose (storing medicine or testing
material, using at the ship,
etc.).
When disposing the refrigerator, remove the
packing materials from the door or take off
the doors but leave the
shelves in place so that
children may not easily
climb inside.
It may cause to lock out the
child.
It may cause an unexpected risk
such as fire, electric shock,
deterioration of stored material or
chemical reaction.
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
Install the refrigerator on the solid and level
floor.
Children should be supervised to ensure
that they do not play with the appliance.
Do not insert the hands or the metal stick
into the exit of cool air, the cover, the bottom
of the refrigerator,
the heatproof grill
(exhaust hole) at
the backside.
Installing it on the unstable
place may cause death by
falling down the refrigerator
when opening or closing the
door.
It may cause electric
shock or injury.
8
w CAUTION
Violating this direction may cause injury or damage house or furniture. Always be careful, please.
Do not insert the hands into the ice bucket
or the ice dispenser.
Do not touch food or containers at the
freezer with wet hands.
Operating the ice maker may
cause injury.
It may cause frostbite.
Do not put ice in thin crystal cup or
ceramic ware.
Supply the automatic ice maker with
drinkable water only
(only for the model
with the dispenser).
It may break cup or ceramic
ware to cause injury.
Drinkable
water
Otherwise, it may cause
any risk.
Do not place the food in disorder inside
the refrigerator.
The food may fall during opening and
closing the door of the refrigerator and hurt
people.
Do not put bottle in the freezer.
Do not insert the hands into the bottom
of the refrigerator.
Carry the refrigerator with the handle bar
at the bottom of the front and the top of
the rear.
It may freeze the contents to
break the bottle to cause
injury.
The iron plate of the
bottom may cause injury.
Otherwise, your hands
may be slipped to cause
injury.
Because the product is
heavy, carrying it alone
may hurt people or
accidents may occur.
Because opening or closing the door of
the refrigerator may cause injury to the
person around it, be careful, please.
Do not put any living
animal in the
refrigerator.
Opening or closing the
door may cause feet or
hands to be caught in
the chink in door or the
child to be get hurt by
the corner.
9
PARTS AND FEATURES
A
M
B
N
P
C
C
D
I
O
J
E
K
F
G
L
H
Use this page to become more familiar with the parts and features.Page references are included for
your convenience.
NOTE: This guide covers several different models. The refrigerator you have purchased may
have some or all of the items listed below. The locations of the features shown below may not
match your model.
A Refrigerator Light
I Pull out Drawer (p. 25)
B Filter (Inside) (p. 26)
J Durabase (p. 25)
C Modular Door Bins (p. 24)
K Divider (p. 25)
D Shelves (p. 22)
L Tilt-Out Door Basket (p. 25)
E Crisper (p. 23)
(Keeps fruits and vegetable fresh and crisper)
M Dairy Bin (p. 24)
F Glide’N’Serve (p. 23)
O Water Tank Cover
G Automatic Icemaker
P Bottle Holder (p.22)
N Utility Bin (p. 24)
H Ice Bin (p. 24)
10
REFRIGERATOR INSTALLATION
INSTALLATION
w WARNING
• To minimize noise and vibration, the refrigerator
MUST be installed on a solidly constructed floor.
• Carpeting and soft tile surfaces are not
recommended.
• Never install the refrigerator on a platform or
weakly supported structure.
1. To avoid vibration, the unit must be level. If
required, adjust the leveling screws to
compensate for unevenness of the floor. The
front should be slightly higher than the rear to
aid in door closing. Leveling screws can be
turned easily by tipping the cabinet slightly. Turn
the leveling screws clockwise (
) to raise the
unit, counterclockwise (
) to lower it.
2. Install this appliance in an area where the
temperature is between 13°C and 43°C. If the
temperature around the appliance is too low or
high, cooling ability may be adversely affected.
3. Too small a distance from adjacent items may
result in lowered freezing capability and
increased electricity consumption charges. Allow
at least 24 in. (61 cm) in front of the refrigerator to
open the doors.
Excessive Weight Hazard
Use two or more people to move and install
refrigerator.
Failure to do so can result in back or other injury.
UNPACKING YOUR REFRIGERATOR
Remove tape and any temporary labels from your
refrigerator before using. Do not remove any
warning-type labels, the model and serial number
label, or the TechSheet that is attached to back
wall of the refrigerator.
To remove any remaining tape or glue, rub the
area briskly with your thumb. Tape or glue residue
can also be easily removed by rubbing a small
amount of liquid dish soap over the adhesive with
your fingers. Wipe with warm water and dry.
Do not use sharp instruments, rubbing alcohol,
flammable fluids or abrasive cleaners to remove
tape or glue. These products can damage the
surface of your refrigerator. For more information,
see the Important Safety Instructions section.
Refrigerator shelves are installed in the shipping
position.
Please reinstall shelves according to your
individual storage needs.
w WARNING
1" (2.54 cm)
When Moving Your Refrigerator:
NEXT
Your refrigerator is heavy. When moving the
refrigerator for cleaning or service, be sure to
protect the floor. Always pull the refrigerator
straight out when moving it. Do not wiggle or
walk the refrigerator when trying to move it, as
floor damage could occur.
1. Clean your refrigerator thoroughly and wipe off
all dust accumulated during shipping.
2. Install accessories such as ice cube bin,
drawers, shelves, etc., in their proper places.
They are packed together to prevent possible
damage during shipment.
3. Let your refrigerator run for at least 2 or 3 hours
before putting food in it. Check the flow of cold
air in the freezer compartment to ensure proper
cooling. Your refrigerator is now ready for use.
w WARNING
Explosion Hazard
BASE COVER
Keep flammable materials and vapors, such as
gasoline, away from refrigerator.
Failure to do so can result in death, explosion
or fire.
• To reduce the risk of electric shock, do not
install the refrigerator in a wet or damp area.
• Select a place where a water supply can be
easily connected for the automatic icemaker.
w CAUTION: Avoid placing the unit near heat
sources, direct sunlight or moisture.
To remove the base cover
1. Open the Freezer Drawer. (Drawer not shown
for clarity.)
2. Once drawer is open there is sufficient
clearance to remove screws on top of cover.
To replace base cover:
• Place cover into position
and insert and tighten
screws.
11
REFRIGERATOR INSTALLATION
HOW TO REMOVE DOOR HANDLES
To move refrigerator through a house door, it maybe necessary to remove refrigerator and freezer door
handles.
NOTE: Handle appearance may vary from illustrations on this page.
1. Removing Refrigerator Handle
• Loosen the set screws
with the 3/32” Allen
wrench and remove the
handle.
NOTE: If the handle
mounting fasteners need
to be tightened or
removed, use a 1/4” Allen
wrench.
Mounting
Fasteners
Set Screw
Allen Wrench
2. Removing Freezer Drawer
Handle
• Loosen the set screws
located on the lower side
of the handle with the 1/8”
Allen wrench and remove
the handle.
NOTE: If the handle
mounting fasteners need
to be tightened or
removed, use a 1/4” Allen
wrench.
12
REFRIGERATOR INSTALLATION
HOW TO REPLACE DOOR HANDLES
NOTE: Handle appearance may vary from illustrations on this page.
1. Replacing Refrigerator Door Handle
• Place the handle on the door by
adjusting handle footprints to fit
mounting fastners and tighten the
set screws with the 3/32” Allen
wrench.
NOTE: If the handle mounting
fasteners need to be tightened or
removed use a 1/4” Allen wrench.
Mounting
Fasteners
2. Replacing Freezer Drawer Handle
• Place the handle on the door by
adjusting handle footprints to fit
mounting fastners and tighten the
set screws on the bottom of the
handle with a 1/8” Allen wrench.
NOTE: If the handle mounting
fasteners need to be tightened or
removed use a 1/4” Allen wrench.
13
REFRIGERATOR INSTALLATION
IMPORTANT: When lifting the hinge free of the
latch, be careful that the door does not fall
forward.
REMOVING AND REPLACING
REFRIGERATOR DOORS
To remove the left refrigerator door:
• Lift the door from the middle hinge pin and
remove the door.
Pull the water tube out of the fitting while pressing
the release ring on the fitting. When you pull out
the tube, first you have to push the collet by
opposite direction of arrow in the upper picture
and tube pull out by direction of arrow.
• Place the door, inside facing up, on a
nonscratching surface.
To remove the right refrigerator door:
• Open door.Loosen top hinge cover screw (1).
Lift up cover (2).
• Remove cover.
• Disconnect wire harness (4).Remove the
grounding screw (5).
• Rotate hinge lever (6)clockwise.
Lift top hinge (7)free of hinge lever latch (8).
IMPORTANT: When lifting the hinge free of the
latch, be careful that the door does not fall
forward.
w CAUTION: Before you begin, remove food and
bins from the doors.
• Open the door. Remove the top hinge cover
screw (1).
• Use a flat-head screwdriver to pry back the
hooks (not shown) on the front underside of the
cover (2). Lift up the cover.
• Remove the cover. Pull out the tube (3).
• Disconnect all the wire harnesses (4).
• Remove the grounding screw(5)
• Rotate hinge lever (6) counterclockwise. Lift the
top hinge (7) free of the hinge lever latch (8).
1
2
2
1
6
3
5
8
4
6
5
4
7
7
8
14
REFRIGERATOR INSTALLATION
Replacing Refrigerator Door:
❿ Right Door
• Lower the door onto middle hinge pin (9).
• Fit top hinge (7) over hinge lever latch (8) and into place.
Rotate lever (6) counterclockwise to secure hinge.
• Install the grounding screw (5) and connect wire harnesses (4).
• Hook tab on door switch side of cover under edge of wire opening in cabinet top.
Position cover (2) into place. lnsert and tighten cover screw (1).
❿ Left Door
• Lower the door onto middle hinge pin (9).
• Fit top hinge (7) over hinge lever latch (8) and into place.
Rotate lever (6) clockwise to secure hinge.
• Install the grounding screw (5) and connect the three wire harnesses (4).
• Push the water supply tube into the hole on the top case and pull it out on the backplate.
• Insert the water supply tube (3) into the connector tube until you see only one scale mark.
(Fully insert the tube over 5/8”(15mm)).
• Hook tab on door switch side of cover (2) under edge of wire opening in cabinet top.
Position cover into place. Insert and tighten cover screw (1).
Correct
Incorrect
9
9
15
REFRIGERATOR INSTALLATION
• With both hands, hold both sides of the door
and pull it up to separate it from the rails.
HOW TO REMOVE AND INSTALL
THE PULLOUT DRAWER
IMPORTANT: To avoid possible injury or product
or property damage, you will need two people to
perform the following instructions.
1. Removing Pullout Drawer
• Pull the drawer open to full extension. Remove the
lower basket (1) by lifting basket from rail system.
(If you tilt the door, it will be easier.)
1
• With both hands, hold the center bar and push it
in to let both rails fitted simultaneously.
• Press both hangers with your thumbs to lift it up.
• Separate the left and right rail cover.
• Remove the screws (2) of the rail on both sides.
2
w CAUTION: When you remove the drawer, do
not hold the handle. If it may come off and it
could cause personal injury.
w CAUTION: When laying the drawer down, be
careful not to damage the floor or hurt your
feet by the sharp edges on hinge side.
16
REFRIGERATOR INSTALLATION
• Make sure you have a right rail cover for each
side.
HOW TO REMOVE AND INSTALL
THE PULLOUT DRAWER
Right
Rail Cover
IMPORTANT: To avoid possible injury or product
or property damage, you will need two people to
perform the following instructions.
Left
Rail Cover
2. Installing Pullout Drawer
• With both hands, hold the center bar and push it
out to let both rails out to full extension
simultaneously.
• Align the top holes of the rail cover with the top
holes of the door supports to assemble the rail
covers.
Assembly Hole
• Hook door supports (1) into rail tabs (2).
1
• With the drawer pulled out to full extension,
insert the lower basket (4) in the rail assembly.
2
4
• Lower door into final position and tighten the
screws (3).
3
w WARNING: To prevent accidental child and
pet entrapment or suffocation risk. DO NOT
allow them to play inside of drawer.
w WARNING: DO NOT step or sit down on
freezer door.
17
REFRIGERATOR INSTALLATION
LEVELING AND DOOR ALIGNMENT
Door Alignment
Leveling
If the space between your doors is uneven, follow
the instructions below to align the doors:
After installing, secure the product with the LEG
not to move left or right.
1. With one hand, lift up the door you want to
raise at middle hinge.
Your refrigerator has two front leveling screws—
one on the right and one on the left. If your
refrigerator seems unsteady or you want the
doors to close easier, adjust the refrigerator’s tilt
using the instructions below:
2. With other hand, use pliers to insert snap ring
as shown.
3. Insert additional snap rings until the doors are
aligned. (Three snap rings are provided with
unit.)
1. Plug the refrigerator’s power cord into a
3-prong grounded outlet. Move the refrigerator
into its final position.
2. Turn the leveling leg clockwise to raise that
side of the refrigerator or counterclockwise to
lower it. It may take several turns of the
leveling leg to adjust the tilt of the refrigerator.
NOTE: Having someone push against the top
of the refrigerator takes some weight off the
leveling legs. This makes it easier to adjust the
legs.
3. Open both doors again and check to make
sure that they close easily. If not, tilt the
refrigerator slightly more to the rear by turning
both leveling screws clockwise. It may take
several more turns, and you should turn both
leveling screws the same amount.
4. Re-adjust if necessary.
5. Replace the base cover.
NOTE: Your new refrigerator is uniquely
designed with two fresh food doors. Either door
can be opened or closed independently of one
another. You may have to exert slight pressure
on doors to get them to close completely.
18
USING YOUR REFRIGERATOR
ENSURING PROPER AIR CIRCULATION
In order to ensure proper temperatures, air must
flow between the refrigerator and freezer sections.
As shown in the illustration below, air enters at top
of freezer and circulates down. From bottom of
freezer, air is forced up to top of refrigerator. Air
enters refrigerator through top vent, then circulates
and exists at bottom, where it returns to freezer.
EXPRESS FRZ.
• Refrigerator control: 0°C to 8°C
The lower the number setting, the colder the
refrigerator compartment will become.
• Freezer Temp Control: -21°C to -13°C
When the setting is at a lower number, the freezer
compartment becomes colder. The refrigerator
compartment becomes warmer because less cold air
flows into the refrigerator.
NOTE: If you want to off display, press and hold
EXPRESS FRZ. key and FREEZER key over 5
seconds at the same time.
NOTE: Touch display once to activate, then touch
again to change the settings or activate a function. If 10
seconds has passed since the display has been
touched, it will be necessary to touch “once” again to
reactivate.
☞ This is to prevent accidental display setting changes.
• EXPRESS FRZ. : Press the EXPRESS FRZ. button
and the LED will turn on. This function will remain
activated for 24 hours and increase the cooling speed
of the freezer and the amount of ice produced.
• Dispenser Lock : Press and hold the LOCK button
for 3 seconds to lock the dispenser. When it is locked,
the dispenser will not operate. To unlock, press and
hold the LOCK button for 3 seconds.
• Filter Reset : It displays in months the number of
months left to exchange the filter from the moment
power is connected to the refrigerator. If you have
changed the filter after 6 months of use, press and
hold the FILTER button 3 seconds or more and the
filter display will be initialized with a buzzing sound.
NOTE: The average life of the filter is 6 months.
w WARNING: If a door is open, the dispenser does not
work.
MULTI-FLOW
• Multi-Flow means powerful and effective cooling
operation. This is especially noticeable when new
food is placed in the refrigerator compartment.
• If water or foreign substances enter the cool air
vent while cleaning, efficiency will be lowered. In
addition, if gasket is damaged, efficiency may be
lowered because of escaping cool air.
Do not block any of cool air vents with food packages.
If the vents are blocked, airflow will be interrupted and
temperature and moisture problems may occur.
IMPORTANT: Because air circulates between both
sections, any odors formed in one section will transfer to
the other. You must thoroughly clean both sections to
eliminate odors. To prevent odor transfer and drying out
of food, wrap or cover foods tightly. (See the Food
Storage Guide section for details.)
SETTING THE CONTROLS
• Your refrigerator has two controls that let you regulate
the temperature in the freezer and refrigerator
compartments.
• Initially set the REFRIGERATOR CONTROL at 3°C
and the FREEZER CONTROL at –18°C. Leave it at
this setting for 24 hours (one day) to stabilize. Then
adjust the compartment temperature as desired.
19
w CAUTION
Display mode setting and its cancellation
1. After opening the door, when the EXPRESS FRZ.
button and the Refrigerator Temperature Control
button are pushed at the same time and hold for
5 seconds or longer, it converts to display Mode.
2. The Display shows OFF in F/R temperature display.
3. In this status, all Loads are off (Compressor/
Fan/Damper/Heater) (The refrigerator Lamp
automatic off function warks normally and can be
displayed)
4. To release display mode, reset display by pressing the
EXPRESS FRZ. button and the Refrigerator
Temperature Control button at the same time and holding
for 5 seconds or longer in status of open the door.
USING YOUR REFRIGERATOR
ADJUSTING CONTROL SETTINGS
FOOD STORAGE GUIDE
Give the refrigerator time to cool down completely
before making final adjustments. It is best to wait
24 hours before doing this. The mid-settings
indicated in the previous section should be
correct for normal household refrigerator usage.
The controls are set correctly when milk or juice
is as cold as you like and when ice cream is firm.
The refrigerator control functions as the
thermostat for the entire appliance (refrigerator
and freezer sections). The higher the number
setting, the longer the compressor will run to
keep the temperature colder. The freezer control
adjusts the cold air flow from the freezer to the
refrigerator. Setting the freezer control to a lower
temperature keeps more cold air in the Freezer
compartment to make it colder.
If you need to adjust temperatures in the
refrigerator or freezer, start by adjusting the
refrigerator. Then wait 24 hours before checking
the freezer temperature. If it is too warm or too
cold, then adjust the freezer control.
Use the settings listed in the chart below as a
guide. Always remember to wait at least 24
hours between adjustments.
Wrap or store food in the refrigerator in airtight
and moisture-proof material unless otherwise
noted. This prevents food odor and taste transfer
throughout the refrigerator. For dated products,
check date code to ensure freshness.
CONDITION/
REASON:
RECOMMENDED
ADJUSTMENT:
■ REFRIGERATOR section
too warm
– Door opened often
– Large amount of food
added
– Room temperature very
warm
Set
REFRIGERATOR
control to next
lower number,
wait 24 hours,
then re-check
■ FREEZER section too
warm/ice not made fast
enough
– Door opened often
– Large amount of food
added
– Very cold room
temperature (can’t cycle
often enough)
– Heavy ice usage
– Air vents blocked by items
Set FREEZER
control to next
lower number,
wait 24 hours,
then re-check
Move items out of
airstream
■ REFRIGERATOR section
too cold
– Controls not set correctly
for your conditions
Set
REFRIGERATOR
control to next
higher number,
wait 24 hours,
then re-check
■ FREEZER section too
cold
– Controls not set correctly
for your conditions
Set FREEZER
control to next
higher number,
wait 24 hours,
then re-check
20
Items
How to
Butter or
margarine
❿ Keep opened butter in a
covered dish or closed
compartment. When storing an
extra supply, wrap in freezer
packaging and freeze.
Cheese
❿ Store in the original wrapping
until you are ready to use it.
Once opened, rewrap tightly in
plastic wrap or aluminum foil.
Milk
❿ Wipe milk cartons. For best
storage, place milk on interior
shelf, not on door shelf.
Eggs
❿ Store in original carton or
Utility Bin on interior shelf, not
on door shelf.
Fruit
❿ Wash, let dry, and store in
refrigerator in plastic bags or
in the crisper. Do not wash or
hull berries until you are ready
to use them. Sort and keep
berries in their original
container in a crisper, or store
in a sloosely closed paper bag
on a refrigerator shelf.
Leafy
vegetables
❿ Remove store wrapping and
trim or tear off bruised and
discolored areas. Wash in cold
water and drain. Place in
plastic bag or plastic container
and store in crisper.
Vegetables
with skins
(carrots,
peppers)
❿ Place in plastic bags or plastic
container and store in crisper.
Fish
❿ Use fresh fish and shellfish the
same day purchased.
Leftovers
❿ Cover leftovers with plastic
wrap or aluminum foil. Plastic
containers with tight lids can
also be used.
USING YOUR REFRIGERATOR
STORING FROZEN FOOD
REFRIGERATOR SECTION
NOTE: For further information about preparing
food for freezing or food storage times, check a
freezer guide or a reliable cookbook.
WATER DISPENSER
Push the dispenser pad with a glass until you
hear a click to get cold water.
Packaging
Successful freezing depends on correct
packaging. When you close and seal the
package, it must not allow air or moisture in or
out. If it does, you could have food odor and taste
transfer throughout the refrigerator and also dry
out frozen food.
Dispenser Switch
Push
Packaging recommendations:
• Rigid plastic containers with tight-fitting lids
• Straight-sided canning/freezing jars
• Heavy-duty aluminum foil
• Plastic-coated paper
• Non-permeable plastic wraps
• Specified freezer-grade self-sealing plastic bags
Follow package or container instructions for
proper freezing methods.
Tray can be easily removed by pressing and
pulling it.
Do not use:
• Bread wrappers
• Non-polyethylene plastic containers
• Containers without tight lids
• Wax paper or wax-coated freezer wrap
• Thin, semi-permeable wrap
w CAUTION: Do not keep beverage cans or
plastic food containers in the freezer
compartment. They may be break if it freezes.
Freezing
Your freezer will not quick-freeze any large
quantity of food. Do not put more unfrozen food
into the freezer than will freeze within 24 hours.
Leave enough space in the freezer for air to
circulate around packages. Be careful to leave
enough room at the front so the door can close
tightly.
Storage times will vary according to the quality
and type of food, the type of packaging or wrap
used (airtight and moisture-proof) and the storage
temperature. Ice crystals inside a sealed package
are normal. This simply means that moisture in
the food and air inside the package have
condensed, creating ice crystals.
NOTE: Allow hot foods to cool at room
temperature for 30 minutes, then package and
freeze. Cooling hot foods before freezing saves
energy.
Tilt up the front of tray slightly and snap the ribs
into the holes to replace the tray.
Holes
21
Ribs
USING YOUR REFRIGERATOR
REFRIGERATOR SHELVES
Sliding Out Shelves
The shelves in your refrigerator are adjustable to
meet your individual storage needs. Your model
may have glass or wire shelves.
Storing similar food items together in your
refrigerator and adjusting the shelves to fit
different heights of items will make finding the
exact item you want easier; it will also reduce the
amount of time the refrigerator door is open,
saving energy.
You can slide glass shelves in and out of your
refrigerator as follows.
• To slide the shelf out, carefully pull front of
shelf toward you.
• To slide shelf in, push shelf in until it stops.
IMPORTANT: Do not clean glass shelves with
warm water when they are cold. Shelves may
break if exposed to sudden temperature changes
or impact, such as bumping. For your protection,
glass shelves are made with tempered glass,
which will shatter into small pebble-sized pieces.
Folding Shelf
You can store taller items such as a gallon
container or bottles by simply push in front half of
shelf underneath back half of shelf. Pull toward
you to returm to a full shelf.
NOTE: Glass shelves are heavy. Use special
care when removing them to avoid dropping
them.
Adjusting Shelves
Remove shelves from the shipping position and
replace shelves in the position you want.
• To remove a shelf—Tilt up the front of the shelf
in the direction of (1) and lift it in the direction of
(2). Pull the shelf out.
BOTTLE HOLDER
Bottles can be stored laterally with this wine
holder. It can be attached to any shelf.
• To reinstall a shelf—Tilt the front of the shelf
up and guide the shelf hooks into the slots at a
desired height. Then lower the front of the shelf
so that the hooks drop into the slots.
Wine holder can be removed by pulling it straight
out and installed by placing it at the end of the
shelf you want and pushing it inward.
w CAUTION : Make sure that shelves are level
from one side to the other. Failure to do so
may result in the shelf falling or spilling food.
22
USING YOUR REFRIGERATOR
CRISPER HUMIDITY CONTROL
GLIDE‘N’SERVE
You can control the amount of humidity in the
moisture-sealed crispers. Store vegetables or
fruits requiring more or less humidity in separate
crispers. Adjust the control to any setting
between HIGH and LOW.
• LOW lets moist air out of the crisper for best
storage of fruits.
• HIGH keeps moist air in the crisper for best
storage of fresh, leafy vegetables.
The Glide‘N’Serve provides storage space with a
variable temperature control that keeps the
compartment colder than refrigerator.
This drawer can be used for large party trays, deli
items, or beverages. (but this drawer can't be
used for vegetable.)
Controls
The control regulates the air temperature in the
drawer. Set control level to COLD (print on
surface) to provide normal refrigerator
temperature. Use the COLDER (print on surface)
setting for meats or other deli items.
NOTE: Cold air directed to the Glide‘N’Serve can
decrease refrigerator temperature. Refrigerator
control may need to be adjusted.
w CAUTION : The glass shelf over the crisper is
not firmly secured. Be careful when tilting.
REMOVING CRISPER
1. To remove, pull the drawer out to full
extension.
2. Lift the front of the crisper up, then pull it
straight out.
3. To install, slightly tilt up the front and insert the
drawer into the frame and push it back into place.
To replace Glide‘N’Serve
1
1. To remove, pull the drawer out to full
extension.
2. Lift the front of the drawer up, then pull it
straight out.
3. To install, slightly tilt up the front and insert the
drawer into the frame and push it back into
place.
To remove the glass
1. Lift up the glass under the crisper cover.
2. Pull the glass up and out.
23
USING YOUR REFRIGERATOR
MODULAR DOOR BIN
FREEZER SECTION
The door bins are removable for easy cleaning
and adjusting.
TILTING DOOR
The tilting door provides easy access for stored
foods.
1. To remove the bin, simply lift the bin up and
pull straight out.
How to use:
2. To replace the bin, slide it in above the desired
support button and push down until it stops.
Tilt the door down and pull it out.
w WARNING : Somebody can be hurt if door
bins are not firmly assembled.
w NOTE : DO NOT adjust a bin that is loaded
with food.
w WARNING: Be careful when you open tilting
door so that you do not injure your foot!
w CAUTION : DO NOT allow children to play
with baskets. Sharp corners on baskets could
cause injury.
ICE BIN
DAIRY BIN
1. To separate the ice bin, pull out the drawer as
much as possible.
1. To remove the dairy bin, simply lift it and pull
straight out.
2. Gently lift and pull out the ice bin.
2. To replace the dairy bin, slide it in above the
desired location and push down until it stops.
3. To install, pull out the drawer as much as
possible and set the ice bin in its correct
position, then push in the drawer.
DRAWER
ICE BIN
UTILITY BIN
Store the utility bin on interior shelf, not on door
shelf.
w CAUTION : Do not use the utility bin as an ice
storage bin in the freezer compartment. The
utility bin can easily break if it freezes.
24
USING YOUR REFRIGERATOR
TILT-OUT DOOR BASKET
DURABASE DIVIDER
You can remove foods easily by tilting out the
wire basket in the freezer compartment.
The Durabase divider allows you to organize the
Durabase area into sections.
1. To remove, pull the bracket upward until you
hear a clicking sound and remove the wire
rack.
2. To replace, hook the end of the rack in the
bracket, and push down until it locks into place.
1
w WARNING : If the Durabase divider is
removed, there is enough open space for
children or pets to crawl inside. To prevent
accidental child and pet entrapment or
suffocation risk, DO NOT allow them to play
inside of drawer.
2
PULL OUT DRAWER
To separate the drawer, push the front left and
right hooks in direction to pull up and remove.
Then gently lift the gear part of rear left and right
side of the drawer and pull it out in direction.
DURABASE
1. To remove the Durabase, push it back to the
end as much as possible. Tilt up the front of
the Durabase and pull straight out.
1
2. To install, insert the Durabase in rail assembly.
3
1
2
To install, reposition the gear part of rear left and
right side of the drawer after pulling out both rails
as much as possible, and gently push down both
left and right side while checking the hook on the
front part.
2
Hook
25
USING YOUR REFRIGERATOR
2. Replace with a new cartridge.
FILTER
It is recommended that you replace the filter
when the water filter indicator icon turns on or
your water dispenser or ice maker performance
decreases noticeably.
Take the new cartridge out of its packaging
and remove protective cover from the o-rings.
After changing the water filter cartridge, reset the
water filter status display and indicator icon by
pressing and holding the Filter Reset button for 3
seconds.
If you can’t turn the filter from side to side, it
isn’t fully inserted. Push it in firmly and twist it
into place. You will hear the snap when it
clicks into place.
With cartridge knob in the vertical position,
push the new filter cartridge into the cover until
it stops.
Using its handle, twist the cartridge clockwise
about 1/4 turn. You will hear the snap when it
clicks into place.
1. Remove the old cartridge.
Place a container
under the hole of
filter holder.
NOTE: When filter is being removed, the water
drains through the hole.
Rotate the knob
of the cartridge
counter clockwise.
3. Flushing the Water System After Replacing
Filter Dispense water through the water
dispenser for 3 minutes to purge the system.
Pull out the filter
cartridge.
26
CARE AND CLEANING
PLASTIC PARTS (covers and panels)
w WARNING
Do not use window sprays, abrasive cleansers, or
flammable fluids. These can scratch or damage the
material.
CONDENSER COILS
Remove Back cover.
Use a vacuum cleaner with an
extended attachment to clean
condenser coils.Vacuum coils
when dusty or dirty.Coils may need to be cleaned as
often as every other month.
Explosion Hazard
Use non-flammable cleaner.
Failure to do so can result in death, explosion, or fire.
LIGHT BULB REPLACEMENT
Both the refrigerator and freezer sections defrost
automatically. However,clean both sections about
once a month to prevent odors. Wipe up spills
immediately.
w WARNING
Electrical Shock Hazard
Before replacing a burned-out light bulb,either
unplug the refrigerator or turn off power at the
circuit breaker or fuse box.
NOTE: Moving the control to the OFF position
does not remove power to the light circuit.
GENERAL CLEANING TIPS
• Unplug refrigerator or disconnect power.
• Remove all removable parts, such as shelves,
crispers, etc. Refer to sections in Using Your
Refrigerator for removal instructions.
• Use a clean sponge or soft cloth and a mild
detergent in warm water.Do not use abrasive or
harsh cleaners.
• Hand wash, rinse and dry all surfaces
thoroughly.
• Plug in refrigerator or reconnect power.
NOTE:
• Not all appliance bulbs will fit your refrigerator. Be sure
to replace the bulb with one of the same size, shape
and wattage.
• The light bulbs will turn off if door is left open for seven
continuous minutes. Shutting door for one second will
light bulbs to come back on.
OUTSIDE
Waxing external painted metal surfaces helps
provide rust protection. Do not wax plastic parts.
Wax painted metal surfaces at least twice a year
using appliance wax (or auto paste wax). Apply
wax with a clean, soft cloth.
For products with a stainless steel exterior, use a
clean sponge or soft cloth and a mild detergent in
warm water. Do not use abrasive or harsh
cleaners. Dry thoroughly with a soft cloth.
To change Refrigerator Light Bulbs
1. Unplug Refrigerator, or disconnect power at the
circuit breaker.
2. If necessary, remove top shelf or shelves.
3. Using a flat instrument, gently pry the lamp cover
loose in the front as shown. Rotate downward to
remove rear tabs.
4. Make sure the bulbs are cool to the touch. Turn
bulbs counterclockwise to remove. Insert new
bulb(s).
5. Replace with a new 40-watt appliance bulb.
6. Assemble in reverse order by snapping the Lamp
Cover in, engaging the rear tabs followed by the front
tabs.
INSIDE WALLS (allow freezer to
warm up so cloth won’t stick)
To help remove odors, you can wash the inside
of the refrigerator with a mixture of baking soda
and warm water. Mix 2 tablespoons baking soda
to 1 quart of water (26 g soda to 1 liter water.) Be
sure the baking soda is completely dissolved so
does it not scratch the surfaces of the
refrigerator.
w CAUTION: While cleaning the inside, do not
spray water.
DOOR LINERS AND GASKETS
Do not use cleaning waxes, concentrated
detergents, bleaches, or cleaners containing
petroleum on plastic refrigerator parts.
27
CARE AND CLEANING
To change freezer light
WHEN YOU GO ON VACATION
1. Unplug refrigerator power cord form outlet.
If you choose to leave the refrigerator on
while you are away, follow these steps to
prepare your refrigerator before you leave.
2. Using a flat instrument, gently pry the lamp
cover loose in the front as shown. Rotate
downward to remove the rear tabs.
1. Use up any perishables and freeze other
items.
3. Make sure the bulb is cool to the touch. Turn
the bulb counterclockwise to remove.
2. Empty the ice bin.
4. Replace with a new 40-watt appliance bulb.
If you choose to turn the refrigerator off
before you leave, follow these steps.
5. Insert tabs on back of cover into slots in
freezer ceiling. Push cover up to snap front into
place.
1. Remove all food from the refrigerator.
2. Depending on your model, set the thermostat
control (refrigerator control) to OFF. See the
Setting the Controls section.
3. Clean refrigerator, wipe it and dry well.
4. Tape rubber or wood blocks to the tops of both
doors to prop them open far enough for air to
get in. This stops odor and mold from building
up.
WHEN YOU MOVE
When you are moving your refrigerator to a new
home, follow these steps to prepare it for the
move.
1. Remove all food from the refrigerator and pack
all frozen food in dry ice.
2. Depending on your model, turn the thermostat
control (refrigerator control) to OFF. See the
Setting the Controls section.
3. Unplug the refrigerator.
4. Clean, wipe and dry thoroughly.
5. Take out all removable parts, wrap them well
and tape them together so they don’t shift and
rattle during the move. Refer to sections in
Using your Refrigerator for removal
instructions.
w CAUTION: DO NOT place fingers inside of
cover. Lamp may be hot.
6. Depending on the model, raise the front of the
refrigerator so it rolls more easily OR screw in
the leveling legs all the way so they don’t
scrape the floor. See the Door Closing
section.
POWER INTERRUPTIONS
1. If the power will be out for 24 hours or less,
keep all refrigerator doors closed to help foods
stay cold and frozen.
2. If the power will be out for more than 24 hours:
7. Tape the doors shut and tape the power cord
to the refrigerator cabinet.
a) Remove all frozen food and store it in a
frozen food locker.
When you get to your new home, put everything
back and refer to the Installing Your
Refrigerator section for preparation instructions.
28
ABOUT THE AUTOMATIC ICEMAKER
NOTE: If the cube size is smaller or larger than
you expected, you can regulate the size with the
cube size button.
Every time you press the cube size button, the
indicator moves up on light. The higher the light
position, the larger the cubes will be. Pressing at
highest position returns indicator to lowest
position.
w WARNING
Personal Injury Hazard
DO NOT insert your hands in to the Icemaker
in operation. It may cause to injure you.
OPERATION INSTRUCTIONS
WHEN YOU SHOULD SET THE
ICEMAKER POWER SWITCH TO
O (OFF)
A newly-installed refrigerator may take
12 to 24 hours to begin making ice.
• When the water supply will be shut off for
several hours.
• When the ice bucket is removed for more than a
minute or two.
• When the refrigerator will not be used for
several days.
Automatic
Shut off Arm
Power Switch
NORMAL SOUNDS YOU MAY HEAR
• The icemaker water valve will buzz as the
icemaker fills with water. If the power switch is
in the I (on) position, it will buzz even if it has
not yet been hooked up to water. To stop the
buzzing, move the power switch to O (off).
The icemaker will produce 12 cubes per cycle—
approximately 90–130 cubes in a 24- hour period,
depending on freezer compartment temperature,
room temperature, number of door openings and
other operating conditions.
If the refrigerator is used before the water
connection is made to the icemaker, set the power
switch to O (off).
When the refrigerator has been connected to the
water supply, set the power switch to I (on).
The icemaker will fill with water when it cools to
freezing. A newly-installed refrigerator may take 12
to 24 hours to begin making ice cubes.
Throw away the first few batches of ice to allow the
water line to clear.
Be sure nothing interferes with the sweep of the
Automatic Shut off Arm.
When the bin fills to the level of the Automatic Shut
off Arm, the icemaker will stop producing ice.
It is normal for several cubes to be stuck together.
If ice is not used frequently, old ice cubes will
become cloudy, taste stale, and shrink.
NOTE: Keeping the power switch in the I (on)
position before the water line is connected can
damage the icemaker.
• You will hear the sound of cubes dropping into
the bin and water running in the pipes as the
icemaker refills.
PREPARING FOR VACATION
Set the icemaker power switch to O (off) and
shut off the water supply to the refrigerator.
If the ambient temperature will drop below
freezing, have a qualified servicer drain the water
supply system to prevent serious property
damage due to flooding from ruptured water lines
or connections.
29
CONNECTING THE WATER LINE
BEFORE YOU BEGIN
WHAT YOU WILL NEED
This water line installation is not warranted by the
refrigerator or icemaker manufacturer. Follow
these instructions carefully to minimize the risk of
expensive water damage.
Water hammer (water banging in the pipes) in
house plumbing can cause damage to
refrigerator parts and lead to water leakage or
flooding. Call a qualified plumber to correct water
hammer before installing the water supply line to
the refrigerator.
To prevent burns and product damage, do not
hook up the water line to the hot water line.
If you use your refrigerator before connecting the
water line, make sure the icemaker power switch
is in the O (off) position.
Do not install the icemaker tubing in areas where
temperatures fall below freezing.
When using any electrical device (such as a
power drill) during installation, be sure the device
is double- insulated or grounded in a manner to
prevent the hazard of electric shock, or is batterypowered.
If a reverse osmosis water filtration system is
connected to your cold water supply, This water
line installation is not warranted by the refrigerator
or icemaker manufacturer.
Follow next instructions carefully to minimize the
risk of expensive water damage.
If a reverse osmosis water filtration system is
connected to your cold water supply, the water
pressure to the reverse osmosis system needs to
be a minimum of 40 to 60 psi (2.8 Kgf/cm2 ~
4.2 Kgf/cm2, less than 2.0~3.0sec to fill a cup of 7oz
capacity).
If the water pressure from the reverse osmosis
system is less than 21 psi (1.5 Kgf/cm2, more than
4.0sec to fill a cup of 7oz capacity):
Check to see whether the sediment filter in the
reverse osmosis system is blocked. Replace the
filter if necessary.
Allow the storage tank on the reverse osmosis
system to refill after heavy usage.
If the issue about water pressure from reverse
osmosis remains, call a licensed, qualified plumber.
All installations must be in accordance with local
plumbing code requirements.
NOTE: Wear eye protection.
For installation, hose set will be provided with the
refrigerator. When reinstalling, the hose must be
discarded and replaced with a new one.
• Copper Tubing, 1/4″ outer
diameter to connect the
refrigerator to the water
supply. Be sure both ends of
the tubing are cut square.
To determine how much tubing you need:
measure the distance from the water valve on the
back of the refrigerator to the water supply pipe.
Then add 8 feet (2.4 m). Be sure there is
sufficient extra tubing (about 8 feet [2.4 m] coiled
into 3 turns of about 10″ [25 cm] diameter) to
allow the refrigerator to move out from the wall
after installation.
• A cold water supply. The water pressure must
be between 147-834 kPa on models without a
water filter and between 280-834 kPa on
models with a water filter.
• Power drill.
• 1/2″″ or adjustable
wrench.
• Straight- and
Phillips-blade
screwdriver.
• Two 1/4″″ outer
diameter
compression nuts
and 2 ferrules
(sleeves) to connect
the copper tubing to
the shutoff valve and the refrigerator water
valve.
• If your existing copper
water line has a flared
fitting at the end, you will
need an adapter (available
at plumbing supply stores)
to connect the water line to the refrigerator OR
you can cut off the flared fitting with a tube
cutter and then use a compression fitting.
• Shutoff valve to
connect to the cold
water line. The shutoff
valve should have a
water inlet with a
minimum inside
diameter of 5/32″ at the point of connection to
the COLD WATER LINE. Saddle-type shutoff
valves are included in many water supply kits.
Before purchasing, make sure a saddle-type
valve complies with your local plumbing codes.
30
CONNECTING THE WATER LINE
5. TIGHTEN THE PIPE CLAMP
INSTALLATION INSTRUCTIONS
Tighten the clamp screws until the sealing
washer begins to swell.
NOTE: Do not overtighten or you may crush
the tubing.
Install the shutoff valve on the nearest frequently
used drinking water line.
1. SHUT OFF THE MAIN WATER SUPPLY
Turn on the nearest faucet to relieve the
pressure on the line.
Washer
2. CHOOSE THE VALVE LOCATION
Pipe Clamp
Choose a location for the valve
that is easily accessible. It is best
to connect into the side of a
vertical water pipe. When it is
necessary to connect into a
horizontal water pipe, make the
connection to the top or side,
rather than at the bottom, to avoid drawing off
any sediment from the water pipe.
Clamp Screw
6. ROUTE THE TUBING
Route the tubing between the cold water line
and the refrigerator.
Route the tubing through a hole drilled in the
wall or floor (behind the refrigerator or
adjacent base cabinet) as close to the wall as
possible.
NOTE: Be sure there is sufficient extra tubing
(about 8 feet coiled into 3 turns of about 10″
diameter) to allow the refrigerator to move out
from the wall after installation.
3. DRILL THE HOLE FOR THE VALVE
Drill a 1/4″ hole in the
water pipe (even if using a
self-piercing valve) using a
sharp bit. Remove any
burrs resulting from drilling
the hole in the pipe. Take
care not to allow water to
drain into the drill. Failure to drill a 1/4″ hole
may result in reduced ice production or
smaller cubes.
7. CONNECT THE TUBING TO THE
VALVE
4. FASTEN THE SHUTOFF VALVE
Fasten the shutoff valve to the cold water pipe
with the pipe clamp.
Place the compression nut and ferrule
(sleeve) for copper tubing onto the end of the
tubing and connect it to the shutoff valve.
Make sure the tubing is fully inserted into the
valve. Tighten the compression nut securely.
NOTE: Commonwealth of Massachusetts
Plumbing Codes 248CMR shall be adhered
to. Saddle valves are illegal and use is not
permitted in Massachusetts. Consult with your
licensed plumber.
Pipe Clamp
Saddle-Type
Shutoff Valve
Inlet End
Vertical Cold
Water Pipe
NOTE: Commonwealth of Massachusetts
Plumbing Codes 248CMR shall be adhered
to. Saddle valves are illegal and use is not
permitted in Massachusetts. Consult with your
licensed plumber.
Saddle-Type
Shutoff Valve
Compression
Nut
Packing Nut
Outlet Valve
31
Ferrule (sleeve)
CONNECTING THE WATER LINE
8. FLUSH OUT THE TUBING
10. TURN THE WATER ON AT THE
SHUTOFF VALVE
Turn the main water
supply on and flush out
the tubing until the water
is clear.
Shut the water off at the
water valve after about
one quart of water has
been flushed through the
tubing.
Tighten any connections that leak.
Reattach the compressor compartment
access cover.
9. CONNECT THE TUBING TO THE
REFRIGERATOR
Removing and Replacing Valve Cover
11. PLUG IN THE REFRIGERATOR
NOTE:
• Before making the connection to the
refrigerator, be sure the refrigerator power
cord is not plugged into the wall outlet.
Arrange the coil of tubing so that it does not
vibrate against the back of the refrigerator or
against the wall. Push the refrigerator back
to the wall.
1. Remove the plastic flexible cap from the
water valve.
12. START THE ICEMAKER
2. Place the compression nut and ferrule
(sleeve) onto the end of the tubing as
shown.
Set the icemaker power switch to the ON
position. The icemaker will not begin to
operate until it reaches its operating
temperature of –9°C or below. It will then
begin operation automatically if the icemaker
power switch is in the I (on) position.
3. lnsert the end of the copper tubing into the
connection as far as possible. While
holding the tubing, tighten the fitting.
w CAUTION: Check to see if leaks occurs
at water line connections.
Tubing Clamp
1/4 " Tubing
1/4 "
Compression Nut
Ferrule
(sleeve)
Refrigerator
Connection
32
TROUBLESHOOTING GUIDE
• The defrost timer will click when the automatic
defrost cycle begins and ends. The thermostat
control (or refrigerator control, depending on the
model) will also click when cycling on and off.
• Rattling noises may come from the flow of
refrigerant, the water line, or items stored on top of
the refrigerator.
• Your refrigerator is designed to run more efficiently
to keep your food items at the desired
temperature. The high efficiency compressor may
cause your new refrigerator to run longer than your
old one, and you may hear a pulsating or highpitched sound.
• You may hear the evaporator fan motor circulating
the air through the refrigerator and freezer
compartments.
• As each cycle ends, you may hear a gurgling
sound due to the refrigerant flowing in your
refrigerator.
• Contraction and expansion of the inside walls may
cause a popping noise.
• Water dripping on the defrost heater during a
defrost cycle may cause a sizzling sound.
• You may hear air being forced over the condenser
by the condenser fan.
• You may hear water running into the drain pan
during the defrost cycle.
UNDERSTANDING SOUNDS YOU
MAY HEAR
Your new refrigerator may make sounds that your
old one didn’t make. Because the sounds are new
to you, you might be concerned about them. Most of
the new sounds are normal. Hard surfaces, like the
floor, walls and cabinets, can make the sounds
seem louder than they actually are. The following
describes the kinds of sounds and what may be
making them.
Check if…
Then…
REFRIGERATOR
DOES NOT
OPERATE
The power supply cord is unplugged.
❿Firmly plug the cord into a live outlet
with proper voltage.
❿Replace the fuse or reset the circuit
breaker.
❿Refer to the Setting the Controls
section on page 19.
❿Wait about 30 minutes for defrost cycle
to end.
VIBRATION OR
RATTLING
NOISE
The refrigerator is not resting solidly on
the floor.
❿Floor is weak or uneven or leveling legs
need adjusting.
See Installation section on page 11.
LIGHTS DO
NOT WORK
The power supply cord is unplugged.
❿Firmly plug the cord into a live outlet
with proper voltage.
❿Turn the refrigerator control to the OFF
position and unplug the refrigerator.
Gently remove the bulb and reinsert.
Then plug in refrigerator and reset the
refrigerator control.
❿Replace with an appliance bulb of the
same wattage, size and shape available
at your local hardware store. (See the
Changing the Light Bulb(s) section on
pages 27–28.) Turn the temperature
control to the OFF position and unplug
the refrigerator prior to replacement.
❿Shutting door for one second will light
bulbs to come back on.
A household fuse has blown or circuit
breaker tripped.
The refrigerator control is set to the OFF
position.
Refrigerator is in the defrost cycle.
Light bulb is loose in the socket.
Light bulb has burned out.
Door is left open for seven continuous
minutes.
33
TROUBLESHOOTING GUIDE
COMPRESSOR
MOTOR SEEMS
TO RUN TOO
MUCH
Check if…
Then…
The refrigerator that was replaced was
an older model.
The room temperature is hotter than
normal.
❿Modern refrigerators with more storage
space require more operating time.
❿The motor will run longer under warm
conditions. At normal room
temperatures, expect your motor to
run about 40% to 80% of the time.
Under warmer conditions, expect it to
run even more often.
❿Adding food and opening the door
warms the refrigerator. It is normal for
the refrigerator to run longer in order to
cool the refrigerator back down. Adding
a large amount of food warms the
refrigerator. See the Food Storage
Guide section on page 20. In order to
conserve energy, try to get everything
you need out of the refrigerator at once,
keep food organized so it is easy to find
and close the door as soon as the food
is removed.
❿The refrigerator will take up to 24
hours to cool completely.
The door is opened often or a large
amount of food has just been added.
The refrigerator was recently plugged
in and the refrigerator control was set
correctly.
The refrigerator control is not set
correctly for the surrounding conditions.
The doors are not closed completely.
The condenser coils are dirty.
DOORS WILL
NOT CLOSE
COMPLETELY
The refrigerator is not level.
Food packages are blocking the door
open.
The ice bin, crisper cover, pans,
shelves, door bins or baskets are out
of position.
The gaskets are sticking.
The refrigerator wobbles or seems
unstable.
The doors were removed during
product installation and not properly
replaced.
FROST OR ICE
CRYSTALS ON
FROZEN FOOD
The door is not closing properly.
The door is opened often.
34
❿See the Adjusting Control Settings
section on page 20.
❿Push the doors firmly shut. If they will
not shut all the way, see Doors will
not close completely below.
❿This prevents air transfer and makes
the motor work harder.
Clean the condenser coils. Refer to
the Care and Cleaning section on
pages 27–28.
❿See Leveling and Door Alignment
on page 18.
❿Rearrange food containers to clear
door and door shelves.
❿Push bins all the way in and put
crisper cover, pans, shelves and
baskets into their correct positions.
See the Using Your Refrigerator
section on pages 19–26.
❿Clean gaskets and the surface that
they touch. Rub a thin coat of paraffin
wax on the gaskets after cleaning.
❿Level the refrigerator. Refer to the
Leveling and Door Alignment
section on page 18.
❿Remove and replace the doors
according to the Removing and
Replacing Refrigerator handles and
doors section on pages 12–17, or call
a qualified service technician.
❿See Doors will not close completely
above.
❿When the door is opened, warm,
humid air is allowed in the freezer,
resulting in frost.
TROUBLESHOOTING GUIDE
ICE HAS OFFTASTE OR
ODOR
Check if…
Then…
The icemaker was recently installed.
❿ Discard first few batches of ice to avoid
discolored or off-flavored ice.
❿ Throw away old ice and make new
supply.
❿ Rewrap foods since odors may migrate
to the ice if food is not wrapped
properly.
❿ A filter may need to be installed (or
replaced) to eliminate taste and odor
problems.
❿ See Care and Cleaning section on
pages 27–28.
❿ Empty and wash bin. Discard old cubes.
The ice has been stored for too long.
The food has not been wrapped tightly
in either compartment.
The water supply contains minerals
such as sulfur.
The interior of refrigerator needs
cleaning.
Ice storage bin needs cleaning.
THERE IS
WATER IN THE
DEFROST
DRAIN PAN
The refrigerator is defrosting.
It is more humid than normal.
❿ The water will evaporate. It is normal
for water to drip into the defrost pan.
❿ Expect that the water in the defrost
pan will take longer to evaporate. This
is normal when it is hot or humid.
THE
REFRIGERATOR
SEEMS TO
MAKE TOO
MUCH NOISE
The sounds may be normal for your
refrigerator.
❿ Refer to the Understanding Sounds
You May Hear section on page 33.
THE
ICEMAKER IS
NOT
PRODUCING
ICE OR ICE
CUBES ARE
FREEZING TOO
SLOWLY
The freezer temperature is cold
enough to produce ice.
❿ Wait 24 hours after hook-up for ice
production. See the Setting the
Controls section on page 19.
❿ Check to see if something is holding
the door open.
CUBES
PRODUCED BY
ICEMAKER
ARE TOO
SMALL
Smaller cube size level is selected.
THE DOORS
ARE
DIFFICULT TO
OPEN
The gaskets are dirty or sticky.
Door left open.
Water shutoff valve connecting
refrigerator to water line may be
clogged.
The door is reopened within a short
time after having been opened.
35
❿ Select larger cube size using cube size
selector.
❿ Call a plumber to clear the valve.
❿ Clean gaskets and the surfaces that
they touch. Rub a thin coat of
appliance polish or kitchen wax on the
gaskets after cleaning.
❿ When you open the door, warmer air
enters the refrigerator. As the warm air
cools, it can create a vacuum. If the
door is hard to open, wait 5 minutes to
allow the air pressure to equalize, then
see if it opens more easily.
TROUBLESHOOTING GUIDE
TEMPERATURE
IS TOO WARM
OR THERE IS
INTERIOR
MOISTURE
BUILDUP
Check if…
Then…
The air vents are blocked. Cold air
circulates from the freezer to the fresh
food section and back again through
air vents in the wall dividing the two
sections.
The doors are opened often.
❿ Locate air vents by using your hand to
sense airflow and move all packages
that block vents and restrict airflow.
Refer to Multi-Flow on page 19 for the
location of air vents.
❿ When the door is opened, warm humid
air is allowed into the refrigerator. The
more the door is opened, the faster the
humidity builds up, and the more warm
air the refrigerator must cool. In order to
keep the refrigerator cool, try to get
everything you need out of the
refrigerator at once, keep food
organized so it is easy to find and close
the door as soon as the food is
removed.
❿ Refer to the Setting the Controls
section on page 19.
Wait 24 hours for temperatures to
stabilize or even out. If the temperature
is too cold or too warm, move the dial
one number at a time.
❿ Adding food warms the refrigerator. It
can take a few hours for the refrigerator
to return to normal temperature.
❿ Wrap food tightly and wipe off damp
containers prior to storing in the
refrigerator to avoid moisture
accumulation. If necessary, repackage
food according to the guidelines in the
Food Storage Guide section on page 20.
❿ See Doors will not close completely
on page 34.
❿ In humid weather, air carries moisture
into refrigerator when doors are opened.
❿ It is normal for droplets to form on the
back wall after the refrigerator selfdefrosts.
The control is not set correctly for the
surrounding conditions.
A large amount of food has just been
added to the refrigerator or freezer.
The food is not packaged correctly.
The doors are not closing completely.
The weather is humid.
A self-defrost cycle was completed.
36
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising