CNB Technology DBM-21VF Owner's manual

Add to my manuals
54 Pages

advertisement

CNB Technology DBM-21VF Owner's manual | Manualzz
 Diagonal 6mm (1/3”) Sony IT CCD
* Ultra High Resolution (60OTVL]
* Selectable, Day 6 Night
* 3-Axis, Easy Install [Option]
CCD
COLOR CCD DSP DIGITAL DIGITAL COLOR
EZ
COLOR DOME CAMERA
O USER INFORMATION
1 RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION! TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert
Л the user to the presence of un-insulated "dangerous voltage” within the product's enclosure
that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence
of important operating and maintenance-(servicing) instructions in the literature accompanying
the appliance.
THE GRAPHIC SYMBOLS WITH SUPPLEMENTAL MARKING ARE ON THE BOTTOM OF THE SYSTEM.
“WARNING-TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE.”
COLOR DOME CAMERA
O USER INFORMATION
INFORMATION
This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part
15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment
Is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at their own expense.
WARNING
The manufacturer could void the user's authority to operate the equipment.
CAUTION
To prevent electric shock and risk of fire hazards:
* Do not Use power sources except for that specified.
* Do not expose this appliance to rain or moisture.
COLOR DOME CAMERA # fr )
OS CONTENTS
Thank you for purchasing this COLOR VIDEO CAMERA.
Before using this camera, please read this operation manual carefully
to obtain the best result and keep this manual for future reference.
1. SAFETY INSTRUCTIONS ----------------- 5 8. COMMUNICATION PROTOCOL -------- 28
2. PRECAUTIONS -----------=-==================> 6 9. OPERATING САМЕНА --------------------- 30
3. FEATURES ---—---———-——————nnnnnn 7 10. SPECIFICATION 48
4. COMPOSITION ---------------------==-e........ 8 CUT ED ~~~" 48
5. INSTALLATION -------------------------------- 11 24V AC/ 12V DC Input Mode! 50
6. NAME AND FUNCTIONS ----------------- 18 11. TROUBLESHOOTING ------------------ 52
7. CONNECTIONS--——>mmeneeenenenemns 24
( a Y COLOR DOME CAMERA
O 1. SAFETY INSTRUCTIONS
Read Instructions
Read all of the safety and operating instructions
before using the product.
Retain Instructions
Save this instructions for later use.
Cleaning,
Unplug this appliance from wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
Water and Moisture.
Do not use this product near water or moisture.
( For example. near a bathtub, wash bowl,
kitchen sink, or laundry tub, in a wet basement,
or near swimming pool, etc.)
Installation
Do not place this product on an unstable cart,
stand, or table. The product may fall causing
serious Injury to a child or adult, and damage
to the product.
Use only with a cart or stand recommended
by the manufacturer, or sold with the product.
Mounting should follow the manufacturer's
instructions, and should use a mounting accessory
recommended by manufacturer.
Power source
This product should be operated only from
the type of power source indicated on the
marking label.
If you are not sure of the type of power supplied
to your home, consult your dealer or local
power company.
COLOR DOME CAMERA Г, a )
@ 2. PRECAUTIONS
2 Do not install the camera in extreme temperature conditions.
Operate the camera under conditions where temperatures are within —10°C to 50°C.
Especially be careful for ventilation under high temperature.
9 Do not install or use the camera in an environment where the humidity is high.
It can cause the image quality to be poor.
9 Do not install the camera under unstable lighting conditions.
Severe lighting change or flicker can cause the camera to work improperly.
2 Never use the camera close to a gas or oil leak.
It can cause malfunctions to occur.
» Do not disassemble the camera.
There are no user repairable parts inside.
9 Do not drop the camera or subject them to physical shocks.
It can cause malfunctions to occur.
9 Never keep the camera face to strong light directly.
It can damage CCD.
9 Do not expose the camera to rain or spill liquid on it.
If it gets wet, wipe it with dry cloth immediately.
Liquids can contain minerals that corrode the electronic components.
strong electromagnetic field, irregularity such as noise on the monitor may appear.
6 ® NOTE When this camera is installed near wireless communication devices that —
E (N % COLOR DOME CAMERA
O 3. FEATURES
1. Diagonal 6mm (1/37) Sony IT CCD 4. Selectable, day & night
- ICR(OPTIONAL)
2. Min Illumination(F1.2)
- 0.1 LUX (COLOR) 5, RS-485 Communiction Control Support
- 0.01 LUX (B/W) (OPTIONAL)
- Remote OSD menu control via an RS-485
3. High performance menus for functions interface is supported.
- Ultra High Resolution (600TVL)
- SBLC (Super Back Light Compensation)
- DNR (Digital Noise Reduction)
- Privacy zone selectable.
- Motion detection selectable.
- MIRROR (HORIZONTAL)
- Flickerless On/Off.
COLOR DOME CAMERA Г Mm )
04 COMPOSITION
General Dome Camera [c Type]
>) General Dome Camera | A, B Type]
bs Service Monitor Cable »» Service Monitor Cable
»> UTP Harness Cable(Optional) >> UTP Hamess Cable(Optional)
TN © NT
bo Owners Manual >> Guide Pattern >> Owners Manual Pe Guide Pattern
MAN ad
be Mounting Screw »» Mounting Screw
“a
BEI COLOR DOME CAMERA
>) Vandal proof Dome Camera
jou A0
» Service Monitor Cable +» UTP Harness Cable(Optional)
NA |
»» Owner's Manual »» Guide Pattern >> L-Wrench
4447
»> Mounting Screw
>) Flush Dome Camera [Flush type]
A
>> Service Monitor Cable
> 06
>> UTP Harness Cable(Optional) »» Mounting Screw
= ©
» Owner’s Manual >» Guide Pattern »> L-Wrench
ip Surface Mount
Bracket
>) Flush Dome Camera [surface type]
E e Г
be Service Monitor Cable
”D>——2 /7//7/
>> ОТР Нагпезз Cable(Optional) >> Mounting Screw
>
» Owner's Manual » Guide Pattern
>> L-Wrench
Surface Mount
Bracket
( a AAA
General Dome Camera -
@ 5. INSTALLATION [A] Type
Stick the guide pattern on the wall or ceiling.
Drill four holes according to the guide pattern then insert
anchors into the drilled holes.
P Guide Pattern
Attach the camera base to the ceiling or wall using the
supplied four screws.
> Dome Base
Adjust desired focus and scene by turning and moving
the 3-axis camera bracket by hand.
» Dome Cover
Insert coin to the side hole and
twist to remove dome cover >
COLOR DOME CAMERA € 2 )
General Dome Camera -
( [B] Type
Stick the guide pattern on the wall or ceiling.
Drill four holes according to the guide pattern then insert
anchors into the drilled holes.
e) > Guide Pattern
> Dome Base
Attach the camera base to the ceiling or wall using the
supplied four screws.
Adjust desired focus and scene by turning and moving
the 3-axis camera bracket by hand. :
» Mounting Screw
> Dome Cover
( O AAA
General Dome Camera -
[C] Type )
"x
я
=
Stick the guide pattern on the wall or ceiling.
Drill four holes according to the guide pattern then insert
anchors into the drilled holes.
P Guide Pattern
Attach the camera base to the ceiling or wall using the NN
supplied three screws. MN) > Dome Base
Cover the camera bracket with inner dome after adjust
desired focus and scene by turning and moving 3-axis
by hand
P Inner Dome
Adjust desired focus and scene by turning and moving
the 3-axis camera bracket by hand. ds / ,
— » Mounting Screw
> Dome Cover
COLOR DOME CAMERA Ÿ ~ )
Vandal Proof
Dome Camera
1) Stick the guide pattern on the wall or ceiling.
(5) Drill four holes according to the guide pattern then insert
anchors into the drilled holes.
Attach the camera base to the ceiling or wall using the
supplied four screws.
the 3-axis camera bracket by hand.
3)
4
5) Adjust desired focus and scene by turning and moving
6
P Guide Pattern
P Dome Cover
L-Wrench
(7
8
Stick the guide pattern on the wall or ceiling.
Drill four holes according to the guide pattern then insert
anchors into the drilled holes.
Connect the dome base to the surface mount bracket
by screws.
Adjust desired focus and scene by turning and moving
the 3-axis camera bracket by hand.
» Surface Mount
Bracket
» Mounting Screw
» Dome Base
» Tapping Screw
P Dome Cover
L-Wrench
COLOR DOME CAMERA
Flush Vandal Proof
Dome Camera )
» Guide Pattern
COLOR DOME CAMERA Ÿ 2
Flush Dome Camera _
( [Flush Type]
(1) Stick the guide pattern on the wall or ceiling.
5 Drill hole according to the guide pattern and remove
£- Surface Mount Bracket then insert dome camera base
into the drilled holes.
@ Tighten three screws until it dose not turn to fix the
camera on the ceiling
- Cover the camera bracket with inner dome after adjust
5) desired focus and scené by turning and moving 3-axis
by hand
ERE,
ish both side of the Surface Mount ;
acket by hand to release,
AEEEE EEE EE EEEEEEEEEEEEEEEEEEEEnnnnnnnnnnnnnnn?®
Bl Ceiling
1
> Inner Dome
» Dome Cover
JLUK DU : nf;
jo Dome Camera
[Surface Type] )
Stick the guide pattern on the wall or ceiling.
eee eee eee ene een ene eee ; E Ceiling
Drill three hole according to the guide pattern then
insert anchors into the drilled holes.
EEE EEE EEE EEE EEE EEE EEE EEE EAE EEE EEE EERE EEEEEEEEEE EE TE > Guide Pattern
Draw out power / video wires to the connecting places.
Fixed the camera to a ceiling using three mounting
screws.
Cover the camera bracket with inner dome after adjust
desired focus and scene by turning and moving 3-axis
by hand
Turn the dome cover counter clock
Bs wise {io remove. from-the main body.
COLOR DOME CAMERA Г, 7 N
C Fixed Lens Type ® 6.NAME AND FUNCTIONS
(1) Tilt rotation : Adjusting the vertical angle. — :
2 Pan rotation : Adjusting the horizontal angle. :
3) Horizontal rotation : Adjusting the horizontal :
: position of the screen. :
‘
COLOR DOME CAMERA
Vari-focal Lens Type
1. Tilt rotation : Adjusting the vertical angle. ;
2 Panrotation : Adjusting the horizontal angle. :
3) Horizontal rotation : Adjusting the horizontal :
position of the screen.
4) Focus handle : Focus (Far or Near)
5) Zoom handle : Zoom (Tele or Wide)
C Fixed Lens Type
к) Camera Lay-out gronnenenanaanneeneneeen, а
EEE
a
(1) Tilt rotation : Adjusting the vertical angle. — :
2 Panrotation : Adjusting the horizontal angle. :
3) Horizontal rotation : Adjusting the horizontal :
"position of the screen. :
( a Y COLOR DOME CAMERA
Vari-focal Lens Type
>) Camera Lay-out e reee e ae EAA
EEE"
Ч | Tilt rotation : Adjusting the vertical angle.
2 Pan rotation : Adjusting the horizontal angle. |
3) Horizontal rotation : Adjusting the horizontal :
position of the screen.
4 Focus handle : Focus (Far or Near)
5) Zoom handle : Zoom (Tele or Wide)
COLOR DOME CAMERA Wi ~)
Fixed Lens Type
[Flush Dome Camera]
2 13 Pan rotation : Adjusting the horizontal angle. [
4; Horizontal rotation : Adjusting the horizontal :
: position of the screen. *
( - Y COLOR DOME CAMERA
Vari-focal Lens Type D
a
[Flush Dome Camer
— (4) Horizontal rotation : Adjusting the horizontal
‘ position of the screen.
5) Focus handle : Focus (Far or Near)
6) Zoom handle : Zoom (Tele or Wide)
COLOR DOME CAMERA € Mr )
O 7. CONNECTIONS
1. Connecting to Monitor and Power
2 For 24V AC/12V DC Power Type
- The wire is non-polarized.
- Use 24V AC power source or 12V DC power source.
- Use the power rated at least 3.6W / 24VAC and 0.3A (12VDC) :
Remark
video Output 1.0 vp.p
24V AC(20V~28V)or 12V DC(11V-15V),
PEREIRA Max 3.6W / 0.3A
9 For 12V DC Power Type ;
- Connect the video-out jack to the video-in jack of monitor. :
- Connect the power adapter to the power input connecter.
- Use 12V DC === power source.
- Use the power rated at least 180mA (12VDG)
Remark
1.0 Yp.p
12V DC(10V-15V), Max 2.20 /180mA
COLOR DOME CAMERA
2. UTP (Unshielded Twisted Pair)
9 For 24V AC Power Type [UTP Video Output]
aE EEN EF EEE NEF EEE NEE EEE NEE EEE NEE EEE FEE EEE FEE E EEE EEE EE NE EE EE EE EE EE EE EE EERE EE EE EE EEEEEEEEEEENEEEEEEEEEREEEEEEREREEN_
- When using 24V AC power, it is possible to supply the power within 100m.
- Use 4 wires by 2 pair of wires.
- When using 12V DC power, UTP should not be used as the power.
COLOR DOME CAMERA € ) :
9 Connecting to Monitor
- Connect UTP(Unshielded Twisted Pair) wire to the UTP output of the camera directly.
UTP transmitter is included in the camera therefore additional UTP transmitter is not necessary.
- UTP receiver is necessary to connect UTP wire to Monitor or DVR
- When connecting UTP wire, make sure the polarity of the video signal is correct.
- Use UTP wire "CATS 24AWG" to have the best transmission quality.
- The twisted-pair output cannot be used at the same time as the Composite Video output
( (y # COLOR DOME CAMERA
3. Camera remote control connecting (Optional)
Receiver &
Remote Control
(IRC 100 or IRC 200)
Pelco-D
COLOR DOME CAMERA Ÿ
O 8. COMMUNICATION PROTOCOL
PELCO “D” Byte Format
Function KEY UP
2 BYTE | 3BYTE | 4BYTE | 5BYTE | 6 BYTE | 7 BYTE
MSG ID | 0x00 0x20 | 0x00 0x00 | CS
Function | KEY DOWN
2 BYTE | 3BYTE | 4 BYTE | 5BYTE | 6 BYTE | 7 BYTE
MSG D | 0x00 0x40 | 0x00 0x00 | CS
Function | KEY LEFT
1 BYTE | 2BYTE | 3BYTE | 4 BYTE | 5BYTE | 6 BYTE | 7 BYTE
MSG | OxFF ID | 0x01 0x00 | 0x00 0x00 | CS
Function | | KEY RIGHT
1 BYTE | 2BYTE | 3BYTE | 4BYTE | SBYTE | 6 BYTE | 7 BYTE
MSG | OxFF ID 0x00 0x80 0x00 0x00 CS
( ~ Y COLOR DOME CAMERA
Function OSD MENU ON/OFF (Pelco
1 BYTE | 2BYTE | 3BYTE | 4 BYTE | 5BYTE | 6 BYTE | 7 BYTE
MSG | OxFF ID | 0x00 0x23 | 0x00 Ox5F | CS
Function | OSD MENU ON/OFF (Bido Pelco System)
1 BYTE | 2BYTE | 3BYTE | 4BYTE | SBYTE | 6 BYTE | 7 BYTE
MSG | OxFF D | 0x00 0x03 | 0x00 0x62 | CS
Function | OSD MENU ON/OFF (CNB DVR
1 BYTE | 2BYTE | 3BYTE | 4BYTE | 5BYTE | 6 BYTE | 7 BYTE
MSG | OxFF ID 0x40 0x00 0x00 0x00 CS
RRR LT)
ID = 01hex + FFhex : ID check mode
® NOTE (Camera will check the camera ID. If the ID contained in
command packet isn’t identical to the current camera ID,
the received command will be ignored and deleted.)
EEE?
4
COLOR DOME CAMERA € 7 )
®© 9. OPERATING CAMERA
BRIGHTNESS 0-20
ESC FLK OFF. ON
DC LEVEL 0-20
LENS - — FLK OFF ON
SHUTTER 1/60(1/50)1/120(1/100)1/250,1/500,1/700,1HK,1/1600,1/2500
1/5K, 1/7K.1/10K, 1/30K, 1/60K, 1/120K
ATW
RED 0-160
WHITEBAL | MANUAL SUE о
PUSH
ON LEVEL — | 0-20
AGC OFF _
— BW BURST — | OFF, ON
DAY/NIGHT ут
— AUTO DELAY TIME | 1-15
( - Ÿ COLOR DOME CAMERA
IMAGE ADJ
2BLC OFF, LOW, MIDDLE, HIGH
DNR OFF, LOW, MIDDLE, HIGH
SHARPNESS LEVEL 0-20
MIRROR OFF, ON
AREA 1-4 —
DISPLAY OFF, ON
SENSITIVITY 1-24
TOP 8-126
MOTION BOTTOM 8-126
LEFT 4-191
RIGHT 4-191
INITIAL OFF, ON
RETURN +
AREA 1-4
DISPLAY OFF, ON
COLOR WHITE, YELLOW, GREEN, BLUE, RED, BLACK, GRAY
TOP 4-63
PRIVACY BOTTOM 5.64
LEFT 18-205
RIGHT 19-206
INITIAL OFF, ON
En =
EZ
COLOR DOME CAMERA 7 )
COLOR GAIN E] 0-20
| NAL _ OFF «1, ON
RETURN «<
CAM ID 0~255
_ ID DISPLAY I | OFF, ON
OFF |
SoM TLE ON | UP/DN, LE/ RI
LANGUAGE _ENG, CHN(PAL)
MECENAS [ene — — Nr
_ BAUDRATE _ 2400, 4800, 9600, 57600
_ VERSIÓN
INITIAL — OFF«1, ON
_ RETUAN — ALL
INITIAL | OFF«+!' ON
RETURN «
COLOR DOME CAMERA
Use the joystick to navigate between 5 ways.
@ DOWN : Move down / @ UP : Move up
® LEFT : Move left
@) RIGHT : Move right
O MENU(SET):
Press the joystick in its straight position.
@ Sevice Monitor Connecter :
Use service monitor connector to set camera
angle & focus when installing.
(Image cannot be seen if monitor output and service
video output is used simultaneously.)
MAIN MENU - GENERAL
Press MENU button to access the SETUP menu.
Select each sub-menu by
using the « , p=, A ,'W button.
Press the MENU(SET) button to select.
EEE SEE EES EERE EEN AEE NESE EEE EERIE RRR REE EEE
$ QUERER ETRE, y
LENS
WHITE BAL
AGC
DAY/NIGHT
IMAGE ADJ
GENERAL
INITIAL
EXIT
If the OSD MENU is changed then INITIAL will be OFF
(EXCEPT : LENS, CAM ID, BAUDRATE)
COLOR DOME CAMERA ¢ г) )
LENS ESC +
1 WHITE TW
Press the MENU button to access the SETUP menu. } Все ON +
DAY/NIGHT AUTO +
IMAGE ADJ 4!
GENERAL a!
INITIAL ON
LENS ESC J AT : f
= Select LENS using the UP or DOWN button. YOU can change T_T; —;—;——]D—O———T——t]];]— ES
between ESC and DC using the LEFT or RIGHT button.
Select ESC and Press MENU button to display LENS ESC.
1. BRIGHTNESS IA LAA AAA A E LASA ALA,
- Select BRIGHTNESS using the UP or DOWN button. 3 LENS ESC
You can adjust between 0 ~ 20 using the LEFT or RIGHT button. ::
2. FLK (FLICKERLESS) +
- Select FLK using the UP or DOWN button. You can select: EEN Or +
between ON / OFF using the LEFT or RIGHT button. + EXIT - MENU 3
и Hint: Press Menu to go back to Main Menu. "ANA UUNOO ET SNS ENEE NA ENE SAUS Aa ESAS E SENNA TNNE Na ENS E :
{BRIGHTNESS | J
N\
COLOR DOME CAMERA
LENS DC {
Select DC and Press the MENU button to have $ DCLEVEL | |
LENS DC activated. $ FLK OFF
© SHUTTER 1/60 £
1. DC LEVEL(Adjusts brightness of the image.)
- Select DC LEVEL using the UP or DOWN button. You can adjust between 0 ~ 20 level using
the LEFT or RIGHT button.
2. FLK (FLICKERLESS)
- Select FLK using the UP or DOWN button. You can select between ON / OFF using the LEFT or
RIGHT button.
> OFF : You will be allowed to adjust the shutter speed.
3. SHUTTER (Adjusts the shutter speed of the lens.)
- Select SHUTTER using the UP or DOWN button. You can adjust from 1/60(1/50), 1/120(1/100),
1/250, 1/500, 1/700, 1/1K, 1/1600, 1/2500, 1/5K, 1/7K, 1/10K, 1/30K, 1/60K, 1/120K(sec) level
using the LEFT or RIGHT button.
COLOR DOME CAMERA Y fr )
WHITE BAL (White Balance)
Select WHITE BAL using the UP or DOWN button. You can select from ATW, MANUAL,
PUSH using the LEFT or RIGHT button.
1. ATW : Color temperature is automatically adjusted to 2,000°K ~ 10,000°K
2. MANUAL : To set a certain color temperature with RED CONT, BLUE CONT
- Select MANUAL using the UP or DOWN button and press the MENU button to activate
WE MANUAL option. eee
de
RED ——
BLUE | 5 |
EXIT - MENU |
1. RED : To adjust density of RED (0-160)
2. BLUE : To adjust density of BLUE ( 0- 160)
3. PUSH : If the set color temperature does not meet your environment, press the MENU button
to adjust the color temperature to desired setting.
((a Y COLOR DOME CAMERA
AGC (Automatic Gain Control )
Select AGC using the UP or DOWN button. You can select between OFF, ON using the
LEFT or RIGHT button.
1. ON : Select ON using the LEFT or RIGHT button and press the MENU button to activate
AGC option.
AGC
ver H——
EXIT - MENU
1. LEVEL : You can adjust between O - 20 using the LEFT or RIGHT button.
2. OFF : Disable the AGC
COLOR DOME CAMERA E 2 )
DAY / NIGHT EE CoLonsunsT
Select DAY / NIGHT using the UP or DOWN button.
You can select between AUTO, COLOR, B/W, EXT
using the LEFT or RIGHT button.
1. COLOR : for color mode only (DAY mode) a TT Tr
2. B/W : for BLACK and WHITE mode only (NIGHT mode) It is possible to select ON/OFF using
- Select B/W using the LEFT or RIGHT button and press the LEFT or RIGHT button.
the MENU button to activate COLOR BURST option. + aDMDUONODAD Apr óeonecaca cacao kraca taaan aaa aaa
BURST ON
EXIT - MENU
CHANGE DELAY TIME
3. EXT : To switch between COLOR or BLACK and WHITE
depending on external signals. +
NOTE: This function is not supported for this model. :: PELAY TIME :
(Optional) |:
4. AUTO : To switch between COLOR or BLACK and WHITE :! EXIT_MENU
automatically upon the Humination. ep
- Select AUTO using the LEFT or RIGHT button and press Em Pos
MENU button to activate CHANGE DELAY TIME option.
38 ® NOTE In Auto mode D&N camera using external IR may cause D&N filter to flicker. |
( & Y COLOR DOME CAMERA
IMAGE ADJ (Image Adjust)
Select IMAGE ADJ using the UP or DOWN button and press the MENU button to activate
the IMAGE ADJ mode. Dre eee ere eee
IMAGE ADJ
SBLC OFF
DNR LOW
SHARPNESS <
MIRROR OFF
MOTION +
PRIVACY +
COLOR GAIN +
INITIAL ON $
RETURN + 3
1. SBLC (Super Back Light Compensation) : To lighten a darker part of the image
- Select SBLC using the UP or DOWN button. You can select between OFF, LOW, MIDDLE,
HIGH using the LEFT or RIGHT button.
2. DNR (Digital Noise Reduction) : To reduce the image noise especially during the low ambient
lighting conditions.
- Select DNR using the UP or DOWN button. You can adjust between OFF, LOW, MIDDLE, HIGH
using the LEFT or RIGHT button.
| ай’,
COLOR DOME CAMERA € ~ )
3. SHARPNESS ' To adjust SHARPNESS of the image. N U
- Select SHARPNESS using the UP or DOWN button. + sad +
- Select « and press the MEUN button to activate + ° | В ı
SHARPNESS option. | |
- You can adjust the sharpness from 0~20 using the 4 +
LEFT or RIGHT button Te
4. MIRROR
- Select MIRROR using the UP or DOWN button.
You can select from ON/OFF using the LEFT or y UMD DC Ce DT NT a a Di ss
RIGHT button. + MOTION
(1) ON : Horizontal image flip. + AREA 1
(2) OFF : default + —— o
: TOP 19
5. MOTION (Motion Detect) + BOTTOM 62
- Select MOTION using the UP or DOWN button and 3 <a y
press MENU button to activate MOTION DETECT option. РО INITIAL ON
+ RETURN
a aa a SE GE NEE EEN EE EEEEEEE EEE IEEE EEE EE EE em TW
COLOR DOME CAMERA
ши, ия mR mm Ew Em Em ER OE RN EOE (EN ER EEN ER OEM EN ER EEN EE EN OER EL
1) AREA : To specify MOTION DETECTION area
- Select AREA using the UP or DOWN button. You can select from
{ 1 2
area 1-4 position using the LEFT or RIGHT button. $
alla
o CE BN EN BN BN BN BN BN BN BN BN BN BN CC A
2) DISPLAY : To display MOTION DETECTED area on the video |
- Select DISPLAY using the UP or DOWN button. You can select | | 1
between ON/OFF using the LEFT or RIGHT button.
(1) ON : display the MOTION DETECTED area on the screen
(2) OFF : disable oe
3) SENSITIVITY : To setup the motion sensitivity
- Select SENSITIVITY using the UP or DOWN button. You can adjust the motion sensitivity of
a movement from 1-24 using the LEFT or RIGHT button.
(1) 1 : most sensitive (highest)
(2) 24 : least sensitive (lowest)
COLOR DOME CAMERA Ÿ 2 )
4) TOP / BOTTOM / LEFT / RIGHT : Users can specify MOTION DETECTED area.
- Select TOP, BOTTOM, LEFT, or RIGHT using the UP or DOWN button. You can adjust the AREA
using the LEFT or RIGHT button.
(1) TOP : extend or reduce the upper area of the MOTION DETECTED area (8~126)
(2) BOTTOM : extend or reduce the bottom area of the MOTION DETECTED area (8~126)
(3) LEFT : extend or reduce the left side of the MOTION DETECTED area (4~191)
(4) RIGHT : extend or reduce the right side of the MOTION DETECTED area (4~191)
E reduce RIGHT extend
m
à
I
0
5
—
5) INITIAL : To reset the MOTION DETECT mode.
- Select INITIAL using the UP or DOWN button. You can reset the MOTION DETECT mode using the
MENU button.
6) RETURN :To return to IMAGE ADJ MENU
- Select RETURN using the UP or DOWN button. You can return to IMAGE ADJ MENU using the MENU
button.
COLOR DOME CAMERA
6. PRIVACY * ADESDIIOATES Crea SEE An aa a Za NANA ERE RES Rea SS,
- Select PRIVACY using the UP or DOWN button and + PRIVACY +
| | ая АНЕА 1
press the MENU button to active the PRIVACY option. | A rl
+ COLOR WHITE
TOP 15
+ BOTTOM 31
1) AREA : To specify the PRIVACY area au poe
- Select AREA using the UP or DOWN button. You can + INITIAL ON
select area from 1~4 position using the LEFT or RIGHT + A -. “
outton. ~~... nn
2) DISPLAY : To display the Privacy Zone area | 4 E
- Select DISPLAY using the UP or DOWN button. You can |
select between ON/OFF using the LEFT or RIGHT button. al 3
(1) ON : display the Privacy Zone area
(2) OFF : disable
3) COLOR : To change color of privacy zone
- Select COLOR using the UP or DOWN button. You can
adjust from WHITE, YELLOW, GREEN, BLUE, RED, BLACK,
or GRAY using the LEFT or RIGHT button.
COLOR DOME CAMERA € 2
4) TOP / BOTTOM / LEFT / RIGHT : Users can specify PRIVACY ZONE area
- Select TOP, BOTTOM, LEFT, or RIGHT using the UP or DOWN button. You can adjust the privacy
zone using the LEFT or RIGHT button.
(1) TOP : extend or reduce the upper area of the MOTION DETECTED area (4-63)
(2) BOTTOM : extend or reduce the bottom area of the MOTION DETECTED area (5-64)
(3) LEFT : extend or reduce the left side of the MOTION DETECTED area (18-205)
(4) RIGHT : extend or reduce the right side of the MOTIÓN DETECTED area (19-206)
TOP reduce RIGHT extend
F2 anses Efron
| ! i
LEFT <=> 1 € RIGHT — 1 e | =
| | 4 ! :
PES aa : ша e nr НЧ
BOTTOM ;
5) INITIAL : To reset to factory default only on the PRIVACY mode.
- Select INITIAL using the UP or DOWN button. You can reset the PRIVACY mode using the MENU
button.
6) RETURN :To return to IMAGE ADJ MENU
- Select RETURN using the UP or DOWN button. You can return to IMAGE ADJ MENU using the MENU
button.
( O EA
7. COLOR GAIN
- Select COLOR GAIN using the UP or DOWN button and
press MENU button to activate COLOR MODE option.
8. INITIAL :
To reset to factory default only on the IMAGE ADJ mode.
- Select INITIAL using the UP or DOWN button and reset the
IMAGE ADJ mode using the MENU button.
9. RETURN
To return to MAIN MENU
- Select RETURN using the UP or DOWN button and return
to MENU using the MENU button.
GENERAL
Select GENERAL using the UP or DOWN button and
press the MENU button to activate the GENERAL mode. :?
COLOR GAIN
в
BY | В |
EXIT - MENU +
1. B-Y : To adjust density of RED (0-20)
2. B-Y : To adjust density of BLUE (0~20)
GENERAL
CAM ID
ID DISPLAY
CAM TITLE
LANGUAGE
SYNC
BAUDRATE
VERSION
INITIAL
RETURN
OFF
OFF
ENG
INT
2400
ON
COLOR DOME CAMERA ¢ Mm )
1. CAM ID : CAMERA ID ( RS-485 Communication ID)
- Select CAM ID using the UP or DOWN button. You can select between the range 000-255
using the LEFT or RIGHT button.
NOTICE : CAM ID does not reset after user setting.
2. ID DISPLAY (CAMERA ID DISPLAY)
- Select ID DISPLAY using the UP or DOWN button. You can select between ON/OFF using the
LEFT or RIGHT button.
(1) ON : To display camera ID on the screen
(2) OFF : disable
3. CAM TITLE de RR ER
- Select CAM TITLE using the UP or DOWN button. 3 y stains.
You can adjust ON/OFF using the LEFT or RIGHT button. — :: i
(1) ON : To display the camera title on the screen + UPON - CHAR SELECT
(2) OFF : disable O LERI - POSITION
+ EXIT - MENU
- Select ON and Press MENU button to display CAM TITLE. A
(1) UP/DN : To select character using the UP or DOWN button (0~9 А-7)
(2) LE/RI : To select position using the LEFT or RIGHT button.
x
( a % COLOR DOME CAMERA
4. LANGUAGE - Select LANGUAGE using the UP or DOWN button. You can change between
ENG or CHN using the LEFT or RIGHT button.
5. SYNC - Internal Synchronization Type : INT
6. BAUDRATE - Select BAUDRATE using the UP or DOWN button. You can change from
2400bps, 4800bps 9600bps, 57600bps using the LEFT or RIGHT button.
7. VERSION
8. INITIAL : To reset to factory default only on the GENERAL mode.
- Select INITIAL using the UP or DOWN button. You can reset to factory default for GENERAL
mode using the MENU button.
9. RETURN : To return to MENU
- Select RETURN using the UP or DOWN button. You can return to the MENU using the MENU
button.
[y EE: : To reset to factory default.
- Select INITIAL using the UP or DOWN button and reset to factory default using the MENU button.
S41 : To exit out from the OSD setup menu.
- Select EXIT using the UP or DOWN button and close the OSD setup menu by pressing MENU
button.
COLOR DOME CAMERA Г, Mm )
12V DC Input Model O 10. SPECIFICATION
MODEL HIGH RESOLUTION NORMAL RESOLUTION
Signal System PAL | NTSC | — PAL
Image Sensor 1/3 interline CCD
Effective Pixels 500(H)x582(V)
Video Output | Composite : 1.0V p-p, 750
Sync. System Internal Sync
Luminance S/N Ratio 50dB Min.(AGC off)
Horizontal Resolution 400 TVLines (BW 420 TVLines)
Sensitivity 0.1 Lux (color) / 0.01 Lux (B/W) 0.05 Lux (color) / 0.005 Lux (B/W)
ESC (NTSC-1/60 ~ 1/ 120,000), (PAL - 1/50 ~1/ 120,000)
1/ 60(1/50), 1/120(1/100), 1/ 250, 1/500, 1/700, 1/ 1K,
1/ 1.6K, 1/ 2.5K, 1/5K, 1/ 7K, 1/ 10K, 1/ 30K, 1/ 60K, 1/ 120K
DNR OFF, LOW, MIDDLE, HIGH
White Balance ATW, MANUAL , PUSH
48 SBLC OFF, LOW, MIDDLE, HIGH
Manual Shutter
( a о COLOR DOME CAMERA
12V DC Input Model 5
AGC ON, OFF
Day / Night AUTO, COLOR, B/W, EXT
Burst ON, OFF
Motion Detection ON, OFF (4 Programmable Zone)
Privacy ON, OFF (4 Programmable Zone)
Mirror ON(HORIZONTAL), OFF
Sharpness 1-20
Communication RS-485 (Pelco-D, CNB)
OSD Language English / Chinese
Applicable Lens DC Iris / Manual Lens
Supply Voltage 12V DC (+10% -20%)
Power Consumption 180mA / 2.2W (Max)
Operating Temperature/ Humidity -10°C to +50°C / 30% to 80% RH
Storage Temperature/ Humidity -20°C to +60°C / 20% to 90% RH
COLOR DOME CAMERA Г, ~ )
24VAC /12VDC
( Input Model
MODEL HIGH RESOLUTION NORMAL RESOLUTION
Signal System PAL PAL
Image Sensor 1/3 interline CCD
Effective Pixels 510(H)x492(V) | 500(H)x582(V)
Video Output Composite : 1.0V p-p, 750
Sync. System Internal Sync
Luminance S/N Ratio | 50dB Min.(AGC off)
Horizontal Resolution 600 TVLines (BW 650 TVLines) 400 TVLines (BW 420 TVLines)
Sensitivity 0.1 Lux (color) / 0.01 Lux (B/W) 0.05 Lux (color) / 0.005Lux (B/W)
ESC (NTSC-1/ 60 ~ 1/ 120,000), (PAL - 1/ 50 ~1/ 120,000)
1/ 60(1/50), 1/120(1/100), 1/ 250, 1/ 500, 1/ 700, 1/ 1K,
Manual Shutter
1/ 1.6K, 1/ 2.5K, 1/ 5K, 1/ 7K, 1/ 10K, 1/ 30K, 1/ 60K, 1/120K
DNR OFF, LOW, MIDDLE, HIGH
White Balance ATW, MANUAL , PUSH
SBLC OFF, LOW, MIDDLE, HIGH
( a ANA
24VAC / 12VDC
Input Model
AGC ON, OFF
Day / Night AUTO, COLOR, B/W, EXT
Burst ON, OFF
Motion Detection ON, OFF (4 Programmable Zone)
Privacy ON, OFF (4 Programmable Zone)
Mirror ON(HORIZONTAL), OFF
Sharpness 1-20
Communication RS-485 (Pelco-D, CNB)
OSD Language English / Chinese
Applicable Lens DC Iris / Manual Lens
Supply Voltage 24V AC (20V-28V), 12V DC(11V-15V)
Power Consumption 0.3A / 3.6W (Max)
Operating Temperature/ Humidity -10°C to +50°C / 30% to 80% RH
Storage Temperature/ Humidity -20°C to +60°C / 20% to 90% RH
COLOR DOME CAMERA € г )
@11. TROUBLESHOOTING
If you have trouble operating your camera, refer to the following guidelines. If the guidelines do
not help you to solve the problem, contact an authorized technician.
Nothing appears on the screen J
=) Check that the power cord and line connection between the camera and monitor are fixed properly.
=) Check that you have properly connected VIDEO cable to the camera VIDEO output jack.
The image on the screen is dim
») Is lens stained with dirt? Clean your lens with soft, clean cloth.
x) Set the monitor to proper condition.
=) If the camera is exposed to too strong light, change the camera position.
>) Adjust the lens’ focus properly.
The image on the screen is dark _
=) Adjust the contrast feature of the monitor.
=> If you have an intermediate device, set the 750 / Hi-z properly.
> Adjust DC Level, VR level properly.
The camera is not working properly, and the surface of the camera is hot.
E) Check that you have properly connected the camera to an appropriate power source.
The image on the screen flickers. o
=) Check whether the camera is exposed to strong sunlight or fluorescent lighting.
COLOR DOME CAMERA
COLOR DOME CAMERA
DIGITAL DOME CAMERA SERIES
”u в
P/N : 3810-0185F (Ver.0909E) pe
Design and specifications are subject to change without notice.
« o 3)

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement