Passive High Voltage Probes - P5100, P5102, P5120, P6015A

View at www.TestEquipmentDepot.com
Passive High-voltage Probes
P5100 • P5102 • P5120 • P6015A Data Sheet
P5120
DC to 200 MHz
1,000 VRMS CAT II
Floatable up to 600 VRMS CAT II or 300 VRMS CAT III
20x
15 to 25 pF Compensation Range
For TPS2000 Series
UL61010B-2-031, EN61010-2-031, IEC61010-2-031, CSA61010.2.031
P6015A
High Voltage - 20 kVDC / 40 kV Peak (100 ms Pulse Width)
P5120
Features & Benets
P5100
DC to 250 MHz
1000V CAT III (2500 VDC + Peak AC)
100x with Readout Coding
UL3111-1, EN61010-1, IEC61010-2-031, CSA1010.1, CSA1010.2.031
7-30 pF Compensation Range
P5102
DC to 100 MHz
1,000 VRMS CAT II
Floatable up to 600 VRMS CAT II or 300 VRMS CAT III
10x
High Bandwidth - 75 MHz
Silicone Dielectric
Optional 1,000x Readout Coding
Wide Compensation Range (7-49 pF)
Heavy-duty Versatile Ground Lead and Alligator Clip
Applications
Power Supply Design
Design Motor Drive
Electronic Ballast
Power Semiconductors
Switch Mode Control
For THS700 Series
UPS Systems
UL3111-1, EN61010-1, IEC61010-2-031, CSA1010.1, CSA1010.2.031
Power Converters
Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com
Data Sheet
P5100 High-voltage Probe
The P5100 is a low-input capacitance High-voltage Probe (2.5 kV) designed
for higher frequency applications. The probe can be compensated to match
plug-ins and oscilloscopes with nominal input capacitances of 7-30 pF. A
variety of screw-on accessories provide easy connection to the device
under test.
P5102 and P5120 IsolatedChannel™
Applications
In many applications, it is important to be able to isolate the measurement
from earth ground and also to isolate the common voltage between
channels. The P5102, paired with the THS700 Series handheld digital
storage oscilloscopes, and the P5120, coupled with the TPS2000 Series
digital storage oscilloscopes, deliver both the isolation for the measurement
from earth ground and full isolation between the channels.
The 100 MHz P5102 is designed to give you isolated channel performance
for up to 1,000 VRMS CAT II when used with the THS700 Series
oscilloscopes. The 200 MHz P5120 passive high-voltage probe, for use with
the TPS2000 Series oscilloscopes, is designed to give you up to 1,000 VRMS
CAT II of isolated channel performance. A variety of screw-on adapters are
available for easy connection to the device under test.
P6015A High-voltage Probe
For heavy-duty high-performance measurements of voltages over 2.5 kV,
the P6015A is the industry standard. You can measure DC voltages up
to 20 kVRMS and pulses up to 40 kV (pk, 100 ms duration). The 75 MHz
bandwidth enables you to capture fast, high-voltage signals.
2
P6015A
The P6015A uses an environmentally safe silicone compound for a
dielectric and never needs refilling. Other features include: A 7-49 pF
compensation range, small compensation box that fits on adjacent amplifier
inputs, and a readout option for use with most Tektronix digital scopes. With
the readout option, displayed voltage amplitude values will be the actual
signal value rather than understated by a factor of 1,000.
Note: Using the readout version with other than Tektronix digital scopes
may result in an erroneous readout display.
Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com
www.tektronix.com
Passive High-voltage Probes — P5100 • P5102 • P5120 • P6015A
Characteristics
P5100/P5102/P5120/P6015A
Probe
Nominal
Length
Attenuation
Bandwidth
Rise Time
(typical)
Loading
P5100
10 ft.
100x
250 MHz
1.75 ns
10 MΩ / 2.75 pF
P5102
2m
10x
100 MHz
3.5 ns
P5120
3m
20x
200 MHz
2.2 ns
P6015A
P6015A
Opt. 1R
P6015A
Opt. 25
P6015A
Opt. 2R
10 ft.
10 ft.
1000x
1000x
75 MHz
75 MHz
4.0 ns
4.0 ns
2.5 kV
N/A
(DC + Pk AC)
1,000 V CAT III
600 VRMS,
1,000 VRMS
5 MΩ / 11.2 pF
CAT II
CAT II
1,000 VRMS
600 VRMSCAT II,
5 MΩ / 11.2 pF
CATII
300 VRMSCAT III
20 kV
100 MΩ / 3 pF
N/A
20 kV
100 MΩ / 3 pF
N/A
25 ft.
1000x
25 MHz
14 ns
100 MΩ / 4 pF
20 kV
25 ft.
1000x
25 MHz
14 ns
100 MΩ / 4 pF
20 kV
Ordering Information
P5100
100x, 10 ft. High-voltage Probe.
Includes: Cable markers set, 1 ea. crocodile clip, 1 ea. adjustment tool, 1 ea.
hooktip (small), 1 ea. hooktip (large), 1 ea. 18 in. ground lead, 1 ea. 6 in. ground
lead, instruction manual (070-8151-04).
Recommended Accessories
Probe Tip to BNC Adapter – Order 013-0291-xx.
0.080 in. Diameter Spring Tip – Order 206-0060-xx.
P5102
10x, High-voltage Probe for THS700 Series.
Includes: Large retractable hook tip, small retractable hook tip, 6 in. common lead,
18 in. common lead, large crocodile clip, colored cable markers, adjustment tool,
Instruction Manual (070-9294-xx).
P5120
20x, High-voltage Probe for TPS2000 Series.
Includes: Large retractable hook tip, small retractable hook tip, 6 in. common lead,
18 in. common lead, large crocodile clip, colored cable markers, adjustment tool,
instruction manual (071-1463-xx).
Max. Input
VDC or RMS
Max. Float V
Comp.
Range in pF
Readout
7 to 30
Yes
24 to 28
No
15 to 25
No
7 to 49
7 to 49
No
Yes
N/A
7 to 49
No
N/A
7 to 49
Yes
P6015A
1,000x, 10 ft. High-voltage Probe.
Includes: Hook probe tip (206-0463-xx); banana plug tip (134-0016-xx); crocodile
clip - plugs onto ground lead (344-0461-xx); ground lead (196-3363-xx); carrying
case (016-1147-xx); instruction manual (070-8223-xx).
Opt. 1R – 10 ft. with readout.
Opt. 25 – 25 ft. without readout.
Opt. 2R – 25 ft. with readout.
Service (P6015 only)
Opt. C3 – Calibration Service 3 Years.
Opt. C5 – Calibration Service 5 Years.
Opt. D1 – Calibration Data Report
Opt. D3 – Calibration Data Report 3 Years (with Opt. C3).
Opt. D5 – Calibration Data Report 5 Years (with Opt. C5).
Opt. R3 – Repair Service 3 Years.
Opt. R5 – Repair Service 5 Years.
Product(s) are manufactured in ISO registered facilities.
Recommended Accessories for P5100, P5102, P5120:
See P5100, P5102, P5120 Probe Accessories.
Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com