CCG-381K Manual 1.qxd

Rapid Shredder
2400W
Instruction Manual
2 Year Replacement Warranty
RSH-100
! WARNING! Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
0313
To view the full range visit:
www.ozito.com.au
SPECIFICATIONS - MODEL NO. RSH-100
2400W (S1 2000W / S6 (40%) 2400W)
Duty type S1: continuous running duty
S6: continuous-operation / periodic duty
(4 min. Full load, 6 min. No load)
230-240V ~ 50Hz
3910/min
35mm
Sound power level 108 LWA
Double insulated
13kg
Motor:
Input:
No load speed:
Max cutting diameter:
Noise level:
Protection class:
Weight:
KNOW YOUR PRODUCT
2
1
10
9
3
11
4
5
12
13
14
15
16
6
20
17
7
19
18
8
1
1.
2.
3.
4.
5.
6.
7.
8.
Hopper
Transport handle
Locking knob
On/off switch
Reset button
Power cord
Wheel
Wheel cap
9. Push stick
10. Push stick holder
11. Hex (Allen) key
12. Spanner/screwdriver
13. Washers (12.5mm)
14. Washers (8.2mm)
15. Bush bearing
16. Locking nuts
17.
18.
19.
20.
21.
Wheel axle
Stand
Screw & washers
2 x Additional blades
4 x Blade securing screws
(to fit blade)
21
TABLE OF CONTENTS
SPECIFICATIONS…………………………………………Page 1
KNOW YOUR PRODUCT……………………………….. Page 1
INTRODUCTION………………………………………….Page 3
ELECTRICAL SAFETY……………………………………. Page 3
GENERAL SAFETY INSTRUCTIONS…………………… Page 4
ADDITIONAL SAFETY INSTRUCTIONS
FOR SHREDDERS ………………………………………. Page 6
ASSEMBLY…………………………………………………Page 7
OPERATION……………………………………………… Page 9
MAINTENANCE…………………………………………. Page 13
TROUBLESHOOTING…………………………………... Page 15
SPARE PARTS………………………………………………Page 16
DESCRIPTION OF SYMBOLS……………………………Page 16
CONTENTS………………………………………………. Page 17
WARRANTY………………………………………………. Page 18
2
INTRODUCTION
Congratulations on purchasing an Ozito Rapid Shredder.
We aim to provide quality tools at an affordable price.
We hope you will enjoy using this tool for many years.
The RSH-100 Rapid Shredder has been designed for
shredding organic material such as dry plant residue,
twigs, sticks and branches up to 35mm thick. It is
intended for DIY use only.
ELECTRICAL SAFETY
!
WARNING! When using mains-powered equipment, basic safety
precautions, including the following, should always be followed to reduce
risk of fire, electric shock, personal injury and material damage.
Read and understand the manual prior to operating this tool.
Save these instructions and other documents supplied with this tool for future reference.
The electric motor has been designed for 230V and 240V only. Always check that
the power supply corresponds to the voltage on the rating plate.
Note: The supply of 230V and 240V on Ozito tools are interchangeable for
Australia and New Zealand.
This tool is double insulated in accordance with AS/NZS 60335-1;
therefore no earth wire is required.
If the supply cord is damaged, it must be replaced by a qualified electrician or a
power tool repairer in order to avoid a hazard.
Note: Double insulation does not take the place of normal safety precautions
when operating this tool. The insulation system is for added protection against
injury resulting from a possible electrical insulation failure within the tool.
Using an extension lead
Always use an approved extension lead suitable for the power input of this tool.
Before use, inspect the extension lead for signs of damage, wear and ageing.
Replace the extension lead if damaged or defective. When using an extension lead
on a reel, always unwind the lead completely. Use of an extension lead not
suitable for the power input of the tool or which is damaged or defective may
result in a risk of fire and electric shock.
3
!
!
GENERAL POWER TOOL SAFETY WARNINGS
WARNING! Read all instructions. Failure to follow all instructions listed
below may result in electric shock, fire and/or serious injury. The term
"power tool" in all of the warnings listed below refers to your mainsoperated (corded) power tool or battery-operated (cordless) power tool.
SAVE THESE INSTRUCTIONS
Save these instructions
1) Work area
a) Keep work area clean and well lit. Cluttered and dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions
can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way.
Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric shock if
your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when operating
a power tool. Do not use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
b) Use safety equipment. Always wear eye protection. Safety equipment such as
dust mask, non-skid safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c) Avoid accidental starting. Ensure the switch is in the off-position before
plugging in. Carrying power tools with your finger on the switch or plugging in
power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A
wrench or a key left attached to a rotating part of the power tool may result in
personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables
better control of the power tool in unexpected situations.
4
! GENERAL POWER TOOL SAFETY WARNINGS (cont.)
f)
Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and
collection facilities, ensure these are connected and properly used. Use of
these devices can reduce dust related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the rate
for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any
power tool that can not be controlled with the switch is dangerous and must
be repaired.
c) Disconnect the plug from the power source before making any
adjustments, changing accessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools, unplugged & out of the reach of children and do
not allow persons unfamiliar with the power tool or these instructions to
operate the power tool. Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power
tools operation. If damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power tools.
f)
Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in accordance with
these instructions and in the manner intended for the particular type of
power tool, taking into account the working conditions and the work to
be performed. Use of the power tool for operations different from intended
could result in a hazardous situation.
5) SERVICE
a) Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power tool
is maintained.
b) If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.
5
ADDITIONAL SAFETY INSTRUCTIONS FOR SHREDDERS
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Recommendations for the use of a residual current device with a rated residual
current of 30mA or less.
• Only use the shredder in dry conditions and never outdoors when it is raining.
• Do not allow children or any person who has not read this instruction manual or
who is not familiar with the shredder.
• Remember that the operator may be held responsible for accidents or hazards
occurring to other people and/or their property.
• Ensure the shredder is placed on a firm and level surface prior to using.
• Before starting the shredder, ensure the chute is empty.
• Never use the shredder with damaged safety devices or without protection.
• Never operate the shredder unless the chute is in place and securely fastened.
• Wear ear protection when operating the shredder.
• Never look directly into the outlet while the shredder is running as loose debris
may be ejected.
• Do not allow processed material to build up in the discharge chute. This may
prevent proper discharge and can result in kickback of material through the feeding
hopper.
• If the machine becomes clogged, switch off the machine and disconnect from the
power. Allow the cutter to come to a stop. Clear debris from the cutter assembly.
• Never attempt to shred bones, stone, glass, metals, plastic or rags.
• Ensure the customer assembled screws and nuts are properly tightened.
• Wear protective gloves, safety glasses and avoid loose clothing.
!
WARNING! Rotating cutter head. Keep hands and feet out of openings.
• Store shredder upright in a dry place when not in use.
• Never put your hands in the cutter area while the cutter assembly is running or the
shredder is plugged in. The cutter continues to run for a few seconds after the
shredder has been switched off.
• If the cutter strikes any foreign objects or if the shredder starts making any unusual
noise or vibration, switch off the shredder immediately and disconnect the power.
Allow the cutter to come to a stop and take the following steps:
- Inspect for damage
- Check and tighten any loose parts
- Have any damaged parts replaced and/or repaired by an electrician or power
tool repairer.
• Always switch off the shredder and disconnect the power whenever you leave the
work area.
6
ASSEMBLY
!
WARNING!The shredder may require a two person lift. Keep your feet
apart so that you have a stable position, bend at the knees and keep your
back straight.
After removing the shredder from the carton check that the shredder has not been
damaged. Unpack the contents.
Fitting the Wheels and Stand
1. Carefully place the shredder housing upside down on a
flat surface. Place each leg of the stand (18) into the
two holes at the base of the shredder housing (Fig. 1).
Fig. 1
2. Using the spanner/screwdriver (11) secure the legs
using the two screws and washers provided (19), turn
in a clockwise direction (Fig. 2).
Fig. 2
3. Thread the wheel axle (17) through the leg
stand (18) (Fig. 3).
Fig. 3
4. Insert the large washer (13) onto the wheel axle (17) (Fig. 4).
Fig. 4
7
ASSEMBLY (cont.)
5. Place the bush bearing (15) onto the wheel axle (17) (Fig. 5).
Fig. 5
6. Insert the wheel (7) over the bush bearing (15) ensuring
that the larger inner diameter of the wheel is facing
outwards. This allows the wheel cap (8) to be fitted.
Fig. 6
7. Place the small washer (14) onto the wheel axle (17)
followed by the locking nut (16). Secure the flat of the
wheel axle (17) with a 10mm spanner (not included)
and tighten the locking nut (16) using the
spanner/screwdriver (12), turn in a clockwise
direction (Fig. 7).
Fig. 7
8. Place the wheel cap (8) onto the wheel (7) and click in
place (Fig. 8).
9. Repeat steps 4 to 8 for the opposite wheel.
Fig. 8
8
OPERATION
Starting the Shredder
!
WARNING! Prior to starting the motor ensure the shredder is empty.
Ensure you wear safety gloves, safety glasses and earmuffs when the
shredder is in use.
1. Connect the power cord (6) to an appropriate
extension cord and plug the extension cord into the
mains power point (Fig. 9).
Fig. 9
2. To start the shredder move the on/off switch (4) to the
"on" position (Fig. 10). When the shredder is turned
on there will be a short delay before the motor starts
and the speed will fluctuate for a few seconds.
This is normal as the shredder is fitted with a preset
speed controller designed to keep the speed optimal
in use.
Fig. 10
3. To stop the shredder move the on/off switch (4) to the "off" position (Fig. 10).
4. The on/off switch can be disabled to prevent the unit
being turned on. this is a safety feature. To disable
the on/off switch, remove the insert from the end of
the switch by grasping and pulling on the insert (Fig. 11).
Store the insert in a secure location, out of reach of
children. To replace the insert, push it back into
the switch.
Fig. 11
Overload Protection
1. The shredder is equipped with a built in motor protection system that prevents
the motor from being overloaded. The motor will switch off automatically in
the event of overloading.
2. If overloading occurs wait 1-5 minutes and allow the motor to cool down
before restarting the shredder.
3. Move the on/off switch (4) to the "off" position before pressing the reset
button (5).
4. Press the reset button (5) (Fig. 12) and restart
the shredder.
5. If the shredder motor does not restart disconnect
from the mains power supply.
Note: Refer to cleaning out plate hopper section
or troubleshooting.
9
Fig.12
OPERATION (cont.)
Safety Interlock
The shredder is fitted with a safety switch on the closure
between the shredder housing and motor housing (Fig. 13).
This acts as a safety mechanism to prevent the shredder
from operating if it is not closed correctly.
- If the housing is not closed correctly and secured with the
locking knob (3), the safety switch will prevent the shredder
from being turned on.
Fig. 13
- If this occurs disassemble the housing and ensure the contact surfaces are clean. Refit
and tighten the locking knob (3) in a clockwise direction. Take care to correctly line up
the thread on the locking knob (3) before tightening to avoid cross threading.
CAUTION! NEVER loosen the locking knob (3) when the power is on. Always
ensure the power is turned off and pulled out of the mains power.
Replacing Blades
The blades (20) supplied with the shredder are reversible. The blades (20) can also be
re-sharpened if they become blunt over a period of time. One set of spare blades (20)
& bolts (21) is supplied with the shredder. Additional blades (20) & bolts (21) can be
obtained as spare part. Always reverse or replace both blades (20) at the same time.
CAUTION: Blades (20) are sharp, handle with care, it is recommended to use
gardening or safety gloves when handling the blades (20).
To remove the blades proceed as follows:
1. Ensure the shredder is turned off and pulled out of the
mains power. Unscrew the locking knob (3) in an anticlockwise direction (Fig. 14). The thread on the locking
knob is quite long, the operation will require approximately
15 rotations to fully open the housing.
Fig. 14
2. After unscrewing the locking knob (3) lift the housing
upwards (Fig. 15) to gain access to the cutting blades.
Fig. 15
3. There are two blades (20) and these are each fixed to the
rotating blades plate with two hex head screws. To remove
the blades first clean out any debris and build up of material
from the bolt heads. Rotate the blades plate to position the
first blades (20) at the rear U recess of the cover plate,
allowing you to access both screws. Lock the blade plate in
this position by placing the supplied spanner/ screwdriver
(12) through the hole in the cover plate and passing through
the slot in the blade plate (Fig. 16).
Fig. 16
10
OPERATION (cont.)
4. The screws may be tight due to corrosion and dirt
buildup. Ensure that the supplied hex key (11) is a good
fit into the screw and that the hex key is held firmly and
at right angles to the blade plate.
Remove the 2 blade securing screws (21) by rotating the
hex key (11) in the anti-clockwise direction (Fig. 17).
Fig. 17
To remove the second blade repeat steps 3 and 4.
5. If the opposite side of the blades (20) are new, the blades (20) can be reversed
to use the new side. if both sides of the blades (20) are worn then replace the
blades (20) and retighten the blades (20) by following steps 3-5 in reverse. If
new blades (20) are being fitted ensure that the new blade securing screws (21)
are fitted at the same time. Ensure all blade securing screws (21) are tight prior
to operation.
Note: It is recommended to add Loctite® 222 Threadlocker to the thread of
the blade securing screw (21), Loctite® 222 Threadlocker is available from all
Bunnings stores. This assists in securing the screw and reduces the chance of
the blade securing screw (21) vibrating loose whilst in operation
!
WARNING! Ensure the blade securing screws (21) securing the blades are
fully tightened prior to operation. If there is any vibration or abnormal
noise after re-starting the shredder immediately stop operation.
Disconnect from the mains power and check that the blades are
assembled correctly and securely tightened.
6. Once the blades (20) are removed/reversed, lower the housing and tighten the
locking knob (3) by rotating in a clockwise direction. Ensure it is securely fitted
to the housing.
Shredding
!
WARNING! The shredder is not suitable for materials including glass,
metal, plastic bags, stones, fabric, earth covered roots, soft leafy material
and paper waste without a firm consistency (eg. kitchen waste).
!
WARNING! To prevent damage to the shredder it is recommended that
garden material greater than 35mm in diameter is not fed into the shredder.
The following types of material can be used in the shredder:
• Twigs
• Waste from cut bushes
11
• Branches
• Waste from hedge trimming
OPERATION (cont.)
1. Feed the material to be shredded into the feeding
hopper (1) (Fig. 18).
Fig. 18
2. The shredder will automatically pull the material
through the feeding hopper. The push stick (9) can be
used to assist in feeding the garden material (Fig. 19).
Note: The shredder may clog if too much fine material is fed
in. To prevent clogging, mix fine material with larger material.
Fig. 19
Following the below procedures will improve operation and prolong the life of the shredder.
• Branches and twigs should be shredded shortly after they are cut. They become
extremely hard once dry and the maximum cutting diameter is reduced.
• Garden waste such as fresh foliage, creepers and vines contain a lot of moisture,
this can result in material sticking to the cutter head. Such material should be
allowed to dry for a few days before being fed into the shredder.
• Always check material before shredding, ensure it does not contain any stones or
nails as this may severely damage the shredder.
• Material that contains dirt will rapidly blunt the cutting blades and should be avoided.
• Always store the shredder indoors in a dry place.
Composting
The shredded material can be composted in various ways:
•
Placed in a heap directly on the ground (cold composting).
•
Placed in a plastic container, wooden crate, skeleton container or similar
(cold composting).
•
Placed in an insulated compost holder. The heat is then maintained for longer
periods and the rotting process continues during the winter. This method
produces faster results (warm composting).
•
Spread directly onto the garden (surface composting).
!
WARNING! Always use a dust mask and safety gloves when handling
composted material to prevent contamination from micro organisms.
12
MAINTENANCE
!
WARNING! Always disconnect the shredder from the power supply
before performing any maintenance.
The shredder requires very little maintenance. In order to maintain the efficiency and
achieve a long service life observe the following:
•
Keep the air openings at the base of the motor clean and free of
obstructing material.
•
Periodically check that all nuts and screws are secure.
•
Always clean the shredder after each use. Wipe clean the outside of the shredder
with a cloth which has been moistened with a mild detergent and water.
•
Store the shredder upright in a dry place.
Note: Ozito Industries will not be responsible for any damage or injuries caused by
the repair of the tool by an unauthorised person or by mishandling of the tool.
Cleaning
Clean the shredder after each use.
!
WARNING! Never use a high-pressure washer or running water when
cleaning the shredder!
Cleaning the Hopper Plate
!
WARNING! Prior to starting the motor ensure the shredder is empty.
Ensure you wear safety gloves, safety glasses and earmuffs when the
shredder is in use.
Always clean the shredder after each use.
!
WARNING! Never clean the shredder with a high pressure washer or
running water.
1. Ensure the shredder is turned off and pulled out of the
mains power. Unscrew the locking knob (3) in an anticlockwise direction (Fig. 20). The thread on the locking
knob is quite lengthy the operation will require
approximately 3 rotations to fully open the housing.
Fig. 20
2. After unscrewing the locking knob (3) lift the housing
upwards (Fig. 21) to gain access to the cutting blades.
Fig. 21
13
MAINTENANCE (cont.)
3. Carefully clean out the cutting
and discharge area. Ensure that
all debris is removed to prevent
the blades from clogging. The
discharge area should be free of
all organic matter (Fig. 22). If the
shredder is full of organic matter
(Fig. 23) it will burn out the motor
and prevent operation.
Fig. 22
Fig. 23
4. Once the shredder blades are completely clean gently
lower the housing and tighten the locking knob (3) by
rotating in a clockwise direction. Ensure it is securely fitted
to the housing (Fig. 24).
Fig. 24
5. Connect mains power and press the reset button (5) before turning on shredder.
14
TROUBLESHOOTING
Problem
Cause
Solutions
The motor does not run
The shredder may
have been overloaded.
•
Turn the shredder off and
allow it to cool down for
1-5 minutes. Press the
reset button and turn on
the shredder.
The closure between
the shredder housing
and motor housing
has not been closed
correctly.
•
The safety interlock will
not allow power to the
shredder. Open the
housing and ensure the
contact surfaces are clean.
Refit and tighten the
locking knob in a
clockwise direction.
Power failure.
•
Check the power
supply/cord and house
fuse.
The hopper plate is
blocked.
•
Disconnect all power and
unscrew the locking knob.
Carefully clean all debris
and free organic matter
from the discharge area.
Lower the housing and
tighten the locking knob
to ensure it is secure.
The blades are blunt
and need to be
changed.
•
Reverse or replace the
blades.
The motor is cutting out
on overload
The blades are blunt
and need to be
changed.
•
Reverse or replace the
blades.
Smoke is coming out of
the hopper
The cutter assembly is
clogged.
•
Open the shredder and
clean out the hopper.
The material to be
shredded is not pulling
through the unit
15
SPARE PARTS
Limited spare parts are available subject to availability. Please contact your local
Bunnings Special Orders Desk to order the required spare parts.
Most common spare parts listed below
Spare Part/Accessories
Part No.
Blades (set of 2)
SPRSH100-18A
Carbon Brush Pair
SPRSH100-42
Carbon Brush Holder
SPRSH100-43
Switch
SPRSH100-54
Plastic Pin Pair
SPRSH100-60
DESCRIPTION OF SYMBOLS
V
Volts
Hz
Hertz
~
Alternating current
W
Watts
/min
Revolutions or
reciprocation per minute
no
No load speed
dB
Decibel (noise) rating
Regulator compliance mark
Read operator’s manual
Warning
Do not use in wet weather
Disconnect and discontinue use
should the power-cord be damaged
Keep bystanders away
Beware of debris being
ejected from the shredder
Wear eye and ear protection
Wear safety gloves
Danger - Rotating blades.
Keep hands and feet out
of openings while
machine is running
Sound power level
108
Double insulated
16
CARING FOR THE ENVIRONMENT
Power tools that are no longer usable should not be
disposed of with household waste but in an environmentally
friendly way. Please recycle where facilities exist. Check with
your local council authority for recycling advice.
Recycling packaging reduces the need for landfill and raw
materials. Reuse of recycled material decreases pollution in the
environment. Please recycle packaging where facilities exist.
Check with your local council authority for recycling advice.
CONTENTS
1
2
2
2
2
2
2
1
1
x
x
x
x
x
x
x
x
x
Rapid Shredder RSH-100
Wheels
Wheel caps
Small washers
Large washers
Bush bearings
Locking nuts
Spanner/screwdriver
Allen key
1
1
1
2
2
4
1
1
x
x
x
x
x
x
x
x
Wheel axle
Leg stand
Push stick
Screw & washers
Additional blades
Blade securing screws
Push stick holder
Instruction manual
OZITO INDUSTRIES PTY LTD
AUSTRALIA (Head Office)
1 - 23 Letcon Drive, Bangholme, Victoria, Australia 3175
Telephone: 1800 069 486
Facsimile: +61 3 9238 5588
Website: www.ozito.com.au
Email: enquiries@ozito.com.au
17
WARRANTY
YOUR WARRANTY FORM SHOULD BE RETAINED BY YOU AT ALL TIMES. IN ORDER
TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO
YOUR NEAREST BUNNINGS WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT.
PRIOR TO RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE OUR
CUSTOMER SERVICE HELPLINE:
`Australia 1800 069 486
New Zealand 0508 069 486
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
The benefits provided under this warranty are in addition to other rights and remedies which
are available to you at law.
Our goods come with guarantees that cannot be excluded at law. You are entitled to a
replacement or refund for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if
the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Generally you will be responsible for all costs associated with a claim under this warranty,
however, where you have suffered any additional direct loss as a result of a defective product
you may be able to claim such expenses by contacting our customer service helpline above.
2 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 24 months from the original date of purchase
and is intended for DIY (Do It Yourself) use only. If a product is defective it will be replaced in
accordance with the terms of this warranty. Warranty excludes consumable parts, for example:
blades and wheels.
WARNING
The following actions will result in the warranty being void.
•
•
•
•
•
Professional, Industrial or high frequency use.
If the tool has been operated on a supply voltage other than that specified on the tool.
If the tool shows signs of damage or defects caused by or resulting from abuse, accidents
or alterations.
Failure to perform maintenance as set out within the instruction manual.
If the tool is disassembled or tampered with in any way.
OZITO
Australia/New Zealand (Head Office)
1-23 Letcon Drive, Bangholme, Victoria, Australia 3175
OW8