CARVIN ENGINEERING DATA
HIGH-PERFORMANCE CLUB LOUDSPEAKERS
Superb sound with reliability has been one of Carvin’s trademarks for high
performance loudspeakers. High grade components, lightweight Poplar
plywood with dado construction ensures high performance for many years.
For road worthiness, Carvin uses recessed steel handles, steel corners,
expanded metal steel grilles and duratuff™ covering. Front loaded woofers
and wide dispersion titanium high frequency drivers are used to reproduce
the full audio spectrum with superb clarity.
Carvin’s APS™ Active Powered Speakers are more than just another “power
amp in a cabinet”. Biamp or Triamp models feature time aligned circuitry
and adjustable EQ resulting in a much more efficient system that adds clarity to your sound that our competitors do not offer. Every APS™ loudspeaker utilizes Carvin’s DCM power amp technology for continuously rated RMS
power. Carvin’s extensive engineering along with numerous listening tests
have proven our “made in USA” loudspeakers to be superior. Like millions
of users around the world, enjoy using your new loudspeaker.
805
1230
1540/1540A
RECEIVING INSPECTION
INSPECT YOUR LOUDSPEAKER FOR DAMAGE which
may have occurred during shipping. If damage is found,
please notify the shipping company & CARVIN.
SAVE THE CARTON & ALL PACKING MATERIALS. In the
event you have to re-ship your unit, always use the original carton and packing material. CARVIN and the shipping company are not liable for any damage caused by
improper packing. SAVE YOUR INVOICE. It will be
required for warranty service if needed in the future.
SHIPMENT SHORTAGE. If you find items missing, they
may have been shipped separately. Please allow several
days for the rest of your order to arrive before inquiring.
RECORD THE SERIAL NUMBER on the enclosed warranty card for your records. Return the warranty card with
your name and comments to us, or register online at:
1232
1542/1542A
PM15/PM15A
USA customers register online at:
www.carvin.com/registration
All other countries register online at:
www.carvinworld.com/registration
LIMITED WARRANTY
Parts and labor are covered for 1 year on manufacturer’s defects. Warranty does not cover burned out drivers caused by excessive power or distortion, or physical damage caused by general use, moisture or dust.
CAUTION: Square wave distortion from power amps
can destroy drivers much faster than clean RMS
power. The power generated by the APS internal power
amps has the capacity to damage the drivers, in which
case they would not be covered under warranty.
1562
1588/1588A
1584/1584A
SERVICE
In the USA, please call 800-235-2235 for a RMA number (return authorization number). Write this number
on the box and enclose a description of the problem.
Prepay to Carvin 12340 World Trade Drive, SD, CA
92128
Outside the USA, contact your dealer or go to
http://www.carvinworld.com for your nearest service
center. Include a written description of the problem
with serial number and date of purchase.
SW1802
SW1801/SW1801A
76-01230B 0604
2-WAY SYSTEMS SPECS:
805
85 Hz to 17 kHz ±3 dB
72 Hz (-10 dB)
200 watts Continuous
up to 400 watts
98 dB SPL, 1Watt @ 1meter
60° Horizontal, 60° Vertical
Yes
8Ω
No
Two 1/4"
Vented Bass Reflex
Poplar Plywood
12.75"W x 11.5"D x 18.5"H
32.4 x 29 x 47 cm
Net Weight: 24 lbs.
9.8 Kgs
Options: Cover: CV400
Stand: SS20
Frequency Response:
Useable Low Frequency:
Power Handling:
Recommended Amp:
Sensitivity:
Coverage Angles:
Horn Driver Protection:
Nominal Impedance:
Biampable:
Connectors:
Woofer Enclosure Type:
Construction:
Dimensions:
1230
75Hz to 18kHz±3dB
55 Hz (-10 dB)
300 watts Continuous
up to 600 watts
99 dB SPL, 1Watt @ 1meter
90° Horizontal, 45° Vertical
Yes, relay protection
8Ω
Yes
Two 1/4" & Two Speakon™
Vented Bass Reflex
Poplar Plywood
17.5"W x 12"D x 22"H
44.4 x 30.5 x 55.8 cm
36 lbs.
16.3 Kgs
Cover: CV1230
Stand: SS20
1232
80Hz to 18kHz±3dB
61 Hz (-10 dB)
300 watts Continuous
up to 600 watts
99 dB SPL, 1Watt @ 1meter
90° Horizontal, 45° Vertical
Yes, relay protection
8Ω
Yes
Two 1/4" & Two Speakon™
Closed Box
Poplar Plywood
18"W x 13"D x 22"H
45.7 x 33 x 55.8 cm
33 lbs.
15 Kgs
Cover: CVS1232
1540
60Hz to 18kHz±3dB
49 Hz (-10 dB)
400 watts Continuous
up to 800 watts
100 dB SPL, 1Watt @ 1meter
90° Horizontal, 45° Vertical
Yes, relay protection
8Ω
Yes
Two 1/4" & Two Speakon™
Vented Bass Reflex
Poplar Plywood
20"W x 14"D x 26"H
50.8 x 35.5 x 66 cm
51 lbs.
23 Kgs
Cover: CVS1540
1542
65Hz to 18kHz±3dB
52 Hz (-10 dB)
400 watts Continuous
up to 800 watts
101 dB SPL, 1Watt @ 1meter
90° Horizontal, 45° Vertical
Yes, relay protection
8Ω
Yes
Two 1/4" & Two Speakon™
Closed Box
Poplar Plywood
20"W x 14"D x 26"H
50.8 x 35.5 x 66 cm
46 lbs.
21 Kgs
Cover: CVS1542
1562
54Hz to 19kHz±3dB
44 Hz (-10 dB)
600 watts Continuous
up to 900 watts
102 dB SPL, 1Watt @ 1meter
90° Horizontal, 45° Vertical
Yes, relay protection
4Ω
Yes
Two 1/4" & Two Speakon™
Vented Bass Reflex
Poplar Plywood
17"W x 15.25"D x 44.25"H
43 x 38.7 x 112cm
82 lbs.
15 Kgs
Cover: CV1562
3-WAY SYSTEMS SPECS:
1584
50 Hz to 18 kHz ±3 dB
38 Hz (-10 dB)
400 watts Continuous
up to 800 watts
100 dB SPL, 1Watt @ 1meter
90° Horizontal, 45° Vertical
Yes, relay protection
8Ω
Yes
Two 1/4" & Two Speakon™
Vented Bass Reflex
Poplar Plywood
22"W x 15.25"D x 31.5”H
55.8 x 38.7 x 80 cm
Net Weight: 74 lbs.
29.4 Kgs
Options: Cover: CVS1584
Stand: SS20
Frequency Response:
Useable Low Frequency:
Power Handling:
Recommended Amp:
Sensitivity:
Coverage Angles:
Horn Driver Protection:
Nominal Impedance:
Biampable:
Connectors:
Woofer Enclosure Type:
Construction:
Dimensions:
1588
45Hz to 19kHz±3dB
34 Hz (-10 dB)
800 watts Continuous
up to 1200 watts
103 dB SPL, 1Watt @ 1meter
90° Horizontal, 45° Vertical
Yes, relay protection
4Ω
Yes
Two 1/4" & Two Speakon™
Vented Bass Reflex
Poplar Plywood
25"W x 19.25"D x 48.5”H
63 x 49 x 123 cm
124 lbs.
51 Kgs
Cover: CVS1588
SUBWOOFER SYSTEMS SPECS:
SW1801
40 Hz to 450 Hz ±3 dB
28 Hz (-10 dB)
800 watts Continuous
up to 1600 watts
95 dB SPL, 1Watt @ 1meter
4Ω
Two 1/4" & Two Speakon™
Vented Bass Reflex
Poplar Plywood
24.75"W x 24"D x 34"H
63 x 61 x 86 cm
Net Weight: 93 lbs.
41.7 Kgs
Options: Cover: CVS1230
Stand: SS20
Frequency Response:
Useable Low Frequency:
Power Handling:
Recommended Amp:
Sensitivity:
Nominal Impedance:
Connectors:
Woofer Enclosure Type:
Construction:
Dimensions:
SW1802
35Hz to 1 kHz±3dB
24 Hz (-10 dB)
1600 watts Continuous
up to 3200 watts
97 dB SPL, 1Watt @ 1meter
4Ω
Two 1/4" & Two Speakon™
Vented Bass Reflex
Poplar Plywood
48"W x 24"D x 31"H
122 x 61 x 79 cm
159 lbs.
65.7 Kgs
PM15/PM15A SPECS:
Frequency Response:
Useable Low Frequency:
Power Handling:
Recommended Amp:
Sensitivity:
Coverage Angles:
Horn Driver Protection:
Nominal Impedance:
Biampable:
Connectors:
Woofer Enclosure Type:
Construction:
Dimensions:
60 Hz to 18 kHz ±3 dB
49 Hz (-10 dB)
400w continuous, 800 peak
up to 800 watts
100 dB SPL, 1 Watt @ 1 meter
90° Horizontal, 45° Vertical
Yes
8Ω
Yes
One 1/4", One Speakon™
Vented
Acrylonitrile Butadiene Styrene (ABS)
17.5"W x 14"D x 27"H
44.5 x 35.6 x 68.6 cm
Net Weight: 48 Lbs.
Options: 21.8 Kgs
Cover: CV15
APS™ POWER AMP SPECS:
1540A
20 Hz to 20 kHz ±1 dB
Less than 0.1% @ 90% power
350 watts RMS
300 watts @ 8Ω
N/A
50 watts @ 16Ω
1.5VAC for full output-level set at “0”
Equalization: High ±6dB @ 10 kHz
Mid ±6dB, sweepable 100 Hz-5 kHz
Low ±6dB @100 Hz
Active Crossover Filters: 24dB / octave Linkwitz-Riley
Input/Through: 1/4" balanced & XLR
Imput Impedance: 22kΩ
Common Mode Rejection: 72dB @ 1kHz
Overload Protection: Yes
Power Amp Design: Carvin DCM™ Technology
AC Voltage, VA: 120 or 240 VAC models, 300 VA
Idle VA: 20 VA
AC Connection: 3 prong connector (grounded)
AC Power Cable: 16 ga. (heavier for long runs)
Weight: 55 lbs.
24.9 kg
Options: Cover: CVS1540
Stand: SS20
Frequency Response:
THD:
Total Power :
Low Frequency:
Mid Frequency:
High Frequency:
Sensitivity:
1542A
20 Hz to 20 kHz ±1 dB
Less than 0.1% @ 90% power
350 watts RMS
300 watts @ 8Ω
N/A
50 watts @ 16Ω
1.5VAC for full output-level set at “0”
High ±6dB @ 10 kHz
1584A
20 Hz to 20 kHz ±1 dB
Less than 0.1% @ 90% power
425 watts RMS
300 watts @ 8Ω
75 watts @ 16Ω
50 watts @ 16Ω
1.5VAC for full output-level set at “0”
High ±6dB @ 10 kHz
1588A
20 Hz to 20 kHz ±1 dB
Less than 0.1% @ 90% power
900 watts RMS
700 watts @ 4Ω
120 watts @ 8Ω
80 watts @ 16Ω
1.5VAC for full output-level set at “0”
High ±6dB @ 10 kHz
Mid ±6dB, sweepable 100 Hz-5 kHz
Low ±6dB @100 Hz
24dB / octave Linkwitz-Riley
1/4" balanced & XLR
22kΩ
72dB @ 1kHz
Yes
Carvin DCM™ Technology
120 or 240 VAC models, 300 VA
20 VA
3 prong connector (grounded)
16 ga. (heavier for long runs)
51 lbs.
23.1 kg
Cover: CVS1542
Mid ±6dB, sweepable 100 Hz-5 kHz
Low ±6dB @ 100 Hz
24dB / octave Linkwitz-Riley
1/4" balanced & XLR
22kΩ
72dB @ 1kHz
Yes
Carvin DCM™ Technology
120 or 240 VAC models, 400 VA
20 VA
3 prong connector (grounded)
16 ga. (heavier for long runs)
81 lbs.
36.7 kg
Cover: CVS1584
Stand: SS20
Mid ±6dB, sweepable 100 Hz-5 kHz
Low ±6dB @ 100 Hz
24dB / octave Linkwitz-Riley
1/4" balanced & XLR
22kΩ
72dB @ 1kHz
Yes
Carvin DCM™ Technology
120 or 240 VAC models, 900 VA
25 VA
3 prong connector (grounded)
16 ga. (heavier for long runs)
139 lbs.
63 kg
Cover: CVS1588
SW1801A
20 Hz to 20 kHz ±1 dB
Less than 0.1% @ 90% power
700 watts RMS
700 watts @ 4Ω
N/A
N/A
1.5VAC for full output-level set at “0”
N/A
N/A
N/A
24dB / octave 80Hz, 120Hz, or bypass
1/4" balanced & XLR
22kΩ
72dB @ 1kHz
Yes
Carvin DCM™ Technology
120 or 240 VAC models, 900 VA
25 VA
3 prong connector (grounded)
16 ga. (heavier for long runs)
139 lbs.
63 kg
Cover: CVS1801
The power generated by the APS internal power amps has the capacity to damage the drivers, in which case they would not be covered under warranty.
NON-POWERED MODELS
REAR CONNECT PLATE (non-powered speakers) - Use either 1/4” or
SUGGESTIONS FOR OPTIMAL PERFORMANCE To help control feedback, use a graphic equalizer. Keep the speakers in front of the microphone. Never direct
the microphone towards the speaker. For greater coverage, add additional speakers.
Doubling the speakers adds four times the acoustical power which is more advantagious
than increasing power.
Speakon™ cables for connecting to the power amp and daisy chaining to an additional speaker. For high powered applications, use Speakon™ cables only.
SPEAKER CABLES Use either Carvin’s PH50 speaker cable for up to 50’ or highcurrent 12GA Speakon™ cables for lengths up to 150’. 18GA cables are not
recomended. You can DAISY-CHAIN up to one additional speaker per cable by using
the OUTPUT connector. Be sure the total impedance to the amp is not lower than the
amp’s minimum impedance.
742
PRO SOUND REINFORCEMENT
IMPEDANCE: 8 Ohms
POWER RATING: 400 Watts
JACKS WIRED
PARALLEL
TYPICAL LOUDSPEAKER IMPEDANCE CONFIGURATIONS
Individual speaker or speaker cabinet wiring examples for total impedance.
TWIST-LOK
INPUT
1+ SIGNAL
1– GROUND
2+ NOT USED
2– NOT USED
EXT. SYSTEM
MADE IN THE
USA
Serial No.
Speakon™ & 1/4”
through connectors for
additional speakers
Speakon™ & 1/4” inputs
from power amp output.
STEREO BIAMPING
STEREO
CROSSOVER
Suggested settings
TYPICAL STEREO SETUP
Right Input
Left Input
1-800-854-2235
www.carvin.com
INTERNAL FUSE
90-250 VAC
10 VA ~50-60HZ
MONO
XC3000
SWITCHABLE
TO MONO
[ LOW 1+2]
Electronic Crossover
GND
LIFT
[ LOW 1+2 ]
CHANNEL ONE
HIGH
MID
LOW
PHASE
PHASE
PHASE
CHANNEL TWO
HIGH
MID
LOW
PHASE
PHASE
PHASE
Right High Out
Ch 1 Left
Left Low Out
BRIDGE switch
must be OFF (OUT).
For (stereo) the PARALLEL
switch must be OFF (OUT).
Right Low Out
Left High Out
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
SPEAKER –
1
+ ––BRIDGE–– +
–
SPEAKER
2
CAUTION - TO PREVENT ELECTRICAL SHOCK DO NOT DEFEAT THE SAFETY
GROUND ON THE POWER CORD - DO NOT REMOVE COVER .
WARNING - TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE TO RAIN
OR MOISTURE. REFER SERVICING TO QUALIFED PERSONNEL.
CA UTION
RISK OF ELECTRIC
SHOCK
DO NO T OPEN
SPEAKER
1
–
+ ––BRIDGE–– +
–
SPEAKER
2
120V~60Hz Slow Blow
FUSE 8AG 700VA
PROFESSIONAL STEREO
POWER AMPLIFIER
CAUTION - TO PREVENT ELECTRICAL SHOCK DO NOT DEFEAT THE SAFETY
GROUND ON THE POWER CORD - DO NOT REMOVE COVER .
WARNING - TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE TO RAIN
OR MOISTURE. REFER SERVICING TO QUALIFED PERSONNEL.
SERIAL NUMBER
CAUTION
GND LIFT
PARALLEL
BRIDGE
RISK OF ELECTRIC SHOCK
DO NOT OPEN
LIMITERS
CH1
IN
SPEAKER –
1
+ ––BRIDGE–– +
–
SPEAKER
2
CAUTION - TO PREVENT ELECTRICAL SHOCK DO NOT DEFEAT THE SAFETY
GROUND ON THE POWER CORD - DO NOT REMOVE COVER .
WARNING - TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE TO RAIN
OR MOISTURE. REFER SERVICING TO QUALIFED PERSONNEL.
XLR
PIN 1 GND
PIN 2 POS
PIN 3 NEG
120V~60Hz Slow Blow
FUSE 8AG 700VA
PROFESSIONAL STEREO
POWER AMPLIFIER
PARALLEL
BRIDGE
120V~60Hz Slow Blow
FUSE 8AG 700VA
Low Frequency Amp
SERIAL NUMBER
GND LIFT
PROFESSIONAL STEREO
POWER AMPLIFIER
SERIAL NUMBER
LIMITERS
GND LIFT
PARALLEL
BRIDGE
LIMITERS
CH1
IN
CH1
IN
XLR
PIN 1 GND
PIN 2 POS
PIN 3 NEG
XLR
PIN 1 GND
PIN 2 POS
PIN 3 NEG
High Frequency
Left Highs
Ch 2 Right
Right Highs
Left Full Range
Right Full Range
Left Lows
Right Lows
Solder tinned wires 1/4"
Strip cable insulation back 3/4"
2+
Standard 1/4” Phone Plug
Tip-Sleeve
Speakon™
21-
Sleeve
Tip
1+
• Slip "Securing Hub" then "Cable Clamp" over cable before attaching wires.
• Connection Configuration:
Black (1+) / positive
White (1-) / negative
Red (2+) / positive
Green (2-) / negative
• Solder wires in contacts or use hex screws provided.
Tip (Positive)
Sleeve (Negative)
Twist-Lok
Housing
Contact
Insert
Cable
Clamp
Securing
Hub
POWERED MODELS
APS HOOK-UP
APS
1. INPUT/THRU OUTPUT Use the balanced XLR or 1/4” connectors fea-
ACTIVE POWERED SYSTEMS
APS BI-AMPED/TRI-AMPED LOUDSPEAKERS Carvin’s APS™
Active Powered Speakers are more than just another “power amp in a cabinet”.
With two separate power amps in the 2-way systems and three separate power
amps in the 3-way systems, a more efficient design adds clarity as each amp only
needs to reproduce frequencies for it’s respective driver. Compared to other powered speakers the APS system will deliver more clarity with greater power.
APS POWER AMPS APS loudspeakers utilize Carvin’s DCM power amp technology to supply continuously rated RMS power.
APS TIME ALIGNMENT CIRCUITRY Due to the physical size and placement of various drivers in a speaker enclosure, the sound of each driver reaches your
ears at different times. This difference is enough to cause a slight phase change. To
alleviate this problem, the APS utilizes time delay circuits to time-align the drivers with
one another.
DISTANCE
DELAY 360µs
tured on the rear control panel. Using a balanced source will reduce noise which may
be picked up by the cable. You may DAISY-CHAIN as many APS systems as you
wish. All connectors are wired in parallel.
2. APS EQUALIZATION The APS powered loudspeakers offer a by passable 3-band mid sweep equalizer for custom tuning to the acoustical environment.
The EQ system is engineered specifically for the APS, featuring a boost and cut range
of ±6dB to prevent radical adjustments that could otherwise compromise the sound
of the system. The Mid-band sweep is particularly useful for enhancing critical mid
range frequencies for stage monitoring or for cutting certain frequencies to compensate for room resonances. Press the “EQ IN” switch to activate the equalizer. The
BLUE LED displays when the EQ is active.
3. LEVEL CONTROL The LEVEL control adjusts the output volume of the
APS. Start by setting the LEVEL at “0”. Weak input signals can be boosted by setting the LEVEL at “+6”. Strong signals can be reduced by turning the LEVEL toward
“-12”. The RED LED will flash if the internal power amps start to clip. Turn the LEVEL
control down to avoid clipping. Damage to the drivers can result from operating at
a level where the RED CLIP LED is constantly illuminated.
4. POWER/PROTECT/CLIP INDICATOR Power up your audio source
first, then turn on the APS with the power switch. When the system is active, the LED
will indicate GREEN. When shutting down turn off the APS first, then turn off the
mixer. If any of the power amps are clipping, the LED will indicate RED and you should
reduce the output level. If the system should go into protect mode, the LED will indicate YELLOW and the power amps will shut off. This may occur if; a) the system is
overheated due to clipping the power amps for an extended period of time, b) one of
the internal drivers developed a short or c) the power amps require service.
5. POWER Push this switch to the UP position to apply power to the unit. The
POWER LED will light to show the system is on.
6. AC POWER Use a standard grounded AC cord. Whenever possible, use
dedicated circuits for powered speakers. The powered speakers are available in
either 120V or 240V models.
7. CROSSOVER FREQUENCY SWITCH The CROSSOVER FREQUENCY
switch selects the crossover point for the APS. The 120Hz out setting is generally
used with small to mid sized speakers in your setup. Almost all 12” and 15” woofers
will benefit from the 120Hz setting. The 80Hz (switch in) setting is generally used
with larger 18” woofers.
APS BI-AMP/TRI-AMP REAR PANEL:
2
MID
MID SWEEP
0
0
1kHz
-3
APS ACTIVE ELECTRONIC CROSSOVERS An electronic crossover
ATTENUATION dB
splits the incoming signal into specific frequency ranges before going to the separate
amps for each driver. For superior frequency control and maximum phase accuracy,
the APS utilizes the design of our XC3000 crossover featuring sharp 4th order
24dB/octave Linkwitz-Riley filters. Perfect crossover points are achieved with appropriate frequencies going to each driver. A subsonic filter improves woofer efficiency
by removing extremely low frequencies under 20 Hz that waist power.
Low Frequency
High Frequency
Low
Pass
Filter
High
Pass
Filter
300 Watts
742A, 832A
50 Watts
20Hz
1 kHz
3
LOW
+3
-6
-3
EQ IN
+6
HIGH
0
+3
-6
-3
+6
100Hz
0
742A
TIME-ALIGNED BI-AMP SYSTEM
300 W RMS
-12
5kHz
+6
MADE IN THE
LEVEL
US A
CAUTION
!
+6
+3
-6
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION ± TO PREVENT ELECTRICAL SHOCK DO NOT DEFEAT THE
SAFETY GROUND ON THE POWER CORD. DO NOT REMOVE COVER.
NO USER SERVICEABLE PARTS INSIDE. WARNING ± TO PREVENT FIRE
OR SHOCK HAZARD DO NOT EXPOSE TO RAIN OR MOISTURE. REFER
SERVICING TO QUALIFIED PERSONNEL.
RED
CLIP
THRU OUTPUT
GREEN
PROTECT
POWER
Serial No.
120VAC
60Hz 300VA
INPUT
5
4
1
BI-AMP
YELLOW
6
SW1801 SUBWOOFER
8. CROSSOVER BYPASS SWITCH The crossover bypass switch bypasses the
20 kHz
ATTENUATION dB
internal active crossover allowing the use of an outboard active crossover.
Low Frequency
Low
Pass
Filter
1584A 300 Watts
1588A 700 Watts
20Hz
Mid Frequency
High
Pass
Filter
75 Watts
120 Watts
50 Watts
80 Watts
1 kHz
3
8
High Frequency
Band
Pass
Filter
7
TRI-AMP
CROSSOVER
BYPASS
SW1801A
CROSSOVER
FREQUENCY
120Hz
80Hz
20 kHz
ACTIVE SUBWOOFER SYSTEM
700W RMS
0
-12
HI PASS
OUTPUT
MADE IN THE
LEVEL
US A
!
+6
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION ± TO PREVENT ELECTRICAL SHOCK DO NOT DEFEAT THE
SAFETY GROUND ON THE POWER CORD. DO NOT REMOVE COVER.
NO USER SERVICEABLE PARTS INSIDE. WARNING ± TO PREVENT FIRE
OR SHOCK HAZARD DO NOT EXPOSE TO RAIN OR MOISTURE. REFER
SERVICING TO QUALIFIED PERSONNEL.
RED
CLIP
THRU OUTPUT
YELLOW
GREEN
PROTECT
POWER
Serial No.
120VAC
60Hz 700VA
INPUT
1
4
5
6
Download PDF
Similar pages
832 Data Sheet
spec sheet - Clear Sound Atlanta
SW1802 Sheet
Targus APS Tip A17
Targus APTA19
Targus APTA20
Targus APTA29
CARVIN ENGINEERING DATA BR SERIES BASS ENCLOSURES
Targus APS Tip B02
Targus APS Tip B03