shave door handle systems

TECH SUPPORT: 503.693.1918
WWW.AUTOLOC.COM
SHAVE DOOR HANDLE SYSTEMS
SVPRO3 SVPROA3
SVPRO5 SVPROA5
SVPRO7 SVPROA7
IMPORTANT NOTICE: Upon completion of installation,
you may have extra unused wires on the wiring
harness. Do not be concerned. These wires are used
for features available on other models.
15A FUSE
87
87a
86
RELAY
85
87
87a
86
30
RELAY
85
30
+ PARKING LIGHTS
+12V
+12V
OPTIONAL
PASSENGER
DOOR SOLENOID
WHITE/BLACK (CH6 – 500mA)
RED/BLACK (CH5 – 500mA)
Solenoid
(CH4 – 500 mA)
RELAY
(CH3 – 500 mA)
(CH2 – 500 mA)
87
87a
86
(CH1 – 500 mA)
85
30
(STARTER/IGNITION KILL OUTPUT)
+12V
SWITCH IGNITION POWER
CHASSIS
GROUND
SAFETY
RELAY
87
87a
86
DRIVER
DOOR SOLENOID
Solenoid
85
30
KL800
VALET SWITCH
MULTI-FUNCTION KITS
SVPRO37, SVPRO 310, SVPRO316, SVPRO318,
SVPRO57, SVPRO510, SVPRO516, SVPRO518
Remote Receiver
Connector
BROWN/BLUE
BLUE/WHITE
I M P ORTANT!
Please reference the
receivers wiring diagram for
all other wire connections.
Button 1
Button 2
Button 3
Button 4
GREEN/WHITE
1
87a
DRIVER
86
87
85
87a
86
30
DOOR RELAY
85
30
DOOR RELAY
+
–
FUSE
30A
©2004 The Hoffman Group L.L.C. All rights reserved.
SVPRO3- 1 of 2
PASSENGER
87
Drivers Door
Anytime
2
Passengers Door
Anytime
3
1st channel output
Anytime
4
2nd channel output
Anytime
1+3
3rd channel output
Anytime
2+4
4th channel output
Anytime
1+2
5th channel output
Anytime
3+4
6th channel output
Anytime
Revised 8/13/04
The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above
instructions. Installation by qualified automotive professionals is highly recommended.
1
TECH SUPPORT: 503.693.1918
WWW.AUTOLOC.COM
USER GUIDE AND INSTALLATION MANUAL
WIRING DIAGRAMS
SOLENOID INSTALLATION
ALARM KITS
SVPROA3, SVPROA5, SVPROA7
1. Using the 2 standard screws and washers provided attach the
bracket to the solenoid. Install the smaller screw and washer on the
Remote Receiver
Connector
87a
86
on the door. Ideally you want to mount the solenoid so you have a
87a
86
30
Clean and lubricate the latch.
3. Using the hex bolts mount the solenoid to a clean piece of metal
87
85
DOOR RELAY
DRIVER
PURPLE
direct pull from the door latch to the solenoid. If you are unable to
85
mount the solenoid with a direct pull, relocate the solenoid to best fit
30
DOOR RELAY
+
–
PASSENGER
87
solenoids rear terminal.
2. Remove door’s interior door panel and locate the factory latch.
BROWN/BLUE
GREEN/WHITE
I M P O R T ANT!
Please reference the
receivers wiring diagram for
all other wire connections.
your door panel. In some cases you will need to use the cable
extension kit (SVAEX) to redirect the cable from the latch to the
solenoid. (figure 1)
FUSE
4. Create a loop with the cable and secure with the aluminum crimp
30A
around the door latch. (See figure 2) Run cable through door
avoiding all moving parts to the solenoid.
IMPORTANT NOTICE: Upon completion of installation,
you may have extra unused wires on the wiring
harness. Do not be concerned. These wires are used
for features available on other models.
5. Run cable through the eye of the solenoid, create a loop, and
secure w/ aluminum crimp. (See figure 3)
NOTE: for best performance you will want to keep a little slack in the
OEM
LATCH
CABLE
CRIMP
SOLENOID
CABLE
HOUSING
CABLE
SOLENOID
©2004 The Hoffman Group L.L.C. All rights reserved.
SVPRO3- 2 of 2
CABLE
CRIMP
Revised 8/13/04
The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above
instructions. Installation by qualified automotive professionals is highly recommended.
2