LG | AN-MR200 | Owner`s manual | LG AN-MR200 remote control

OWNER’S MANUAL
MAGIC MOTION REMOTE
Please read this manual carefully before operating your set and retain it
for future reference.
AN-MR200
Remote control (AKB732955)
RF Dongle (EAT614134)
www.lg.com
2
ACCESSORIES
ENERGY AV MODE INPUT
TV
SAVING
1
2
3
4
5
7
0(18
8
9
0
FLASHBK
LIST
6
MARK
FAV
ENTER
VOL
3D
CH
P
A
G
E
MUTE
MENU INFO
VOL
ENTER
BACK
MUTE
Q.MENU
CH
EXIT
L/R SELECT
FREEZE
RATIO
Magic Motion
Remote Control Owner’s manual
and Batteries (AA)
RF Dongle
RF Dongle Cable
Strap
Velcro
REMOTE DESCRIPTION
Pointer (RF transmitter)
Blinks the light when operating.
POWER
Turns the TV on or off.
Home
Home
Home
ENTER/OK
Selects menus or options and
confirms your input.
Press this button to display the
pointer when it disappears from the
screen.
If you press the navigation button
while moving the pointer on the
screen, the pointer disappears, and
the Magic Motion remote control
works as a regular remote control.
To display the pointer again, shake
the Magic Motion remote control
from side to side within 2 minutes
after it disappeared. (If 2 minutes
have passed, press the Enter button
to display the pointer.)
Accesses the Home menu.
Navigation
(up/down/left/right)
OK
ENTER
VOL
MUTE
Scrolls through menus or options.
OK
P
CH
MUTE
P +/-)
/ VOL(
Adjusts the volume level.
P / CH(∧/∨)
MUTE
Scrolls through the saved program or
channels.
MUTE
Mutes all sounds.
Installing Batteries
ꔛ Please
read this manual carefully and use the TV correctly.
the message “Magic motion remote control battery is low. Change the battery.”
is displayed, replace the battery.
ꔛ To replace batteries, open the battery cover, replace batteries (1.5 V AA) matching
and ends to the label inside the compartment, and close the battery cover. Be sure
to point the remote control at the remote control sensor on the TV.
ꔛ To remove the batteries, perform the installation actions in reverse. Don’t mix old or used batteries
with new ones. Close cover.
ꔛ When
3
RF DONGLE
Use LED LCD TV/LCD TV Only.
PDP Model (50/60PZ95/75/57**) don’t need this
device. PDP TV is built in.
3Attach the RF Dongle to the velcro as shown
below and then turn on the TV.
Cable IN
Lamp
*If the RF Dongle for the wireless media box is
attached, attach the RF Dongle for the Magic
Motion remote control on the below right of the
back of the TV.
INSTALLING RF DONGLE
Image shown may differ from your TV.
1 Locate the designated Velcro attachment
location on the TV. Then tear off the
protection paper and attach the Velcro. (The
attachment location is different depending
on the TV model you own)
*To avoid wireless interference, keep the distance
between the RF Dongle and the Wi-Fi dongle at
20 cm.
Velcro
20cm
or
RF SPECIFICATION
The Magic Motion Remote Control
communicates with RF Dongle using a
2.4 GHz bandwidth radio frequency (RF).
*Attach the RF Dongle aligning with the upper left
corner bracket.
86%
2Connect the RF Dongle Cable plug on the RF
Dongle to a USB1 jack on the TV.
Output: 1 dBm or lower
ꔛ Maximum Communication Distance:
10 m (32.8 ft) in an open space
ꔛ Bandwidth: 2.4 GHz
(2.4035 GHz - 2.4783 GHz)
ꔛ Transfer Rate: 250 kbps
ꔛ
4
REGISTERING
PRECAUTIONS TO TAKE
The Magic Motion Remote Control
operates by pairing with your TV.
ENTER
OK
ENTER
OK
MUTE
How to register the Magic Motion
Remote Control
To register the remote control,
press the ENTER (or OK) button
on the remote control while
aiming it at your TV.
How to Re-register the Magic
Motion Remote Control after
Registration Failure
Reset the remote control by
pressing and holding both the
ENTER (or OK) and MUTE
buttons for 5 seconds. (Once the
reset is complete, the light on
the Pointer blinks.) Then repeat
the above procedure to register
the remote control.
HOW TO USE
ENTER
OK
Press ENTER (or OK) button if
there is no pointer on your TV
screen. The pointer will appear
on the screen.
If the pointer has not been used
for a certain period of time, it will
disappear.
You can move the pointer by
aiming the front of the remote
control at your TV then move it
left, right, up or down.
If the pointer does not work
properly after clicking the ENTER
(or OK) button, wait for 10
seconds then use it again.
Use the remote control within the
maximum communication distance (10 m,
32.8 ft). Using the remote control beyond
this distance, or with an object
obstructing it, may cause a
communication failure.
ꔛ A communication failure may occur due to
nearby devices. Electrical devices such as
a microwave oven or wireless LAN
product may cause interference, as this
will use the same bandwidth (2.4 GHz) as
the Magic Motion Remote Control.
ꔛ The Magic Motion Remote Control may
be damaged or may malfunction if it is
dropped or receives a heavy impact.
ꔛ When playing a game using the Magic
Motion Remote Control, hold it securely
by wrapping its strap around your wrist
and adjusting the length with the
adjustable ring.
ꔛ Take care not to bump into nearby
furniture or other people when using the
Magic Motion Remote Control.
ꔛ It is recommended that your wireless
access point be located more than 1 m
(3.28 ft) away from the TV. If the AP is
installed closer than 1 m, the magic
motion remote control may not perform
as expected due to frequency
interference.
ꔛ
Download PDF

advertising