CPYLE
USER’S MANUAL PRO
PCMX240|
La ALT Portable PA w/iPod Dock
www.pyleaudio.com
`
—
QUICK SETUP GUIDE (ENGLISH)
1. Make sure all items listed on the front of this guide are
included in the box.
2, READ SAFETY INSTRUCTION BOOKLET BEFORE USING
THE PRODUCT.
3. MAKE SURE THAT YOU HAVE COMPLETELY CHARGED
THE BATTERY PRIOR TO FIRST USE FOR MAXIMUM
BATTERY LIFE.
4. Study this setup diagram.
5. Place product in an appropriate position for operation.
6. Make sure all input devices such as microphones, CD players, mp3 players, and linked amplifiers/PAs are
turned off and volume settings are set at “zero”
F, Connect all devices as shown above.
8. Connect the stereo outputs to the power amplifier(s), tape decks, and/or audio sources.
9. Switch everything on in the following order.
o audio input sources (i.e. microphones, instruments, CD/MP3 Players)
o last, any amplifiers
10. When turning off, always reverse this operation by,
o turning off amplifiers
o last, any input devices
A
DIAGRAM AND PARTS DESCRIPTION
1: Microphone 1 Balanced
Input with Gain Control
(1/4” and XLR): This jack
can either take a %
balanced or a XLR
balanced cable. An XLR
Cable is included with the
GAIN
microphone.
2. Instrument/Microphone 2
Input with Gain Control 7 =
(1/4”): This mono input | | CHARGE iPod e A
accepts a 4” input such as de = ооо
a microphone, guitar, or low 1 2 3
other musical instrument. ` ‘ OFF
3. iPod/Auxuliary input with é Xe od \ | #
Gain Control (Stereo \ À { [| | O O
RCA): This knob controls
the level of the ¡Pod and the O
RCA input. This stereo
RCA input can be used to connect a CD, MP3, or other audio source. To connect to a portable device with a
1/8” headphone jack, you need a standard ( 1/8” to RCA) adapter which is NOT included.
Master Volume Control: This knob controls the master volume -
Power Adapter (IEC): Insert the included power cable here to charge the unit. Note that it
can run off the power adapter while it simultaneously charges the battery. The charge indicator illuminates
when the battery is charging.
Voltage Selector: Set this to the correct voltage for your location standard.
Power ON/OFF Switch
iPod Charging Switch
Battery Level Indicator: While the unit is powered ON, these four lights indicate the power left in the battery.
Battery life varies based on volume and usage.
10. Link Output: This 4” jack is a stereo line level output that can be connected to the stereo input of an amplifier
or amplified loudspeaker such as another
Ml =
So E
IMPORTANT NOTES
Use this troubleshooting guide if: The sound is distorted at high volumes.
o Input is clipping: Try lowering the input gain or the volume control on your sound source or music instrument.
o Output is clipping: Lower the main volume level.
a There is too much bass: Try adjusting the tone or EQ control on your sound source to lower the bass level.
This will allow you to play the music louder before clipping (distortion) occurs.
o The link cable: is being plugged into the instrument or MIC input instead of the RCA line input.
Important: With all large speakers, an initial “break-in” period is needed to perform at optimal levels. To
properly “break-in”, play an audio source at medium volume for a few hours.
SPECIFICATIONS
Input Voltage: AC 100-120V/ 60Hz 220-240V/ 50Hz
Output Wattage: (Peak) 400W
Output Wattage: (RMS) 15W, 1% THD
Frequency Response: 70Hz~ 50kHz +/- 3dB
Bottom pole mount specifications: Standard Pole Mount found at professional audio retailer:
Depth 80mm (3.157)
Diameter 35.5mm (1.407)
Time required to fully charge : under 4 hours
Battery life: Over 12 hours” at full volume when fully charged.
*Note: Battery life may vary based on temperature, age, and volume usage of product.
">
