toyota prius 2010– tvip v5

toyota prius 2010– tvip v5
TOYOTA PRIUS
2010–
TVIP V5
RS3200 PLUS
PREPARATION
Part #: PT398-47090 NOTE: Part number of this accessory may not be the same as the part number shown.
Conflicts:
Do not install into Manual Transmission Vehicles or Vehicles without RKE systems.
Kit Contents
GBS ECU Bracket
GBS ECU
x1
Status Monitor
x1
Washer
x1
Jumper Connector
x1
Window Label
x1
Additional Items
(may be required)
Item#
V5 Harness
Description
x1
Owner’s Guide
English x2
Spanish x2
x1
Foam Tape
M6 Screw
x3
Wire Tie
x1
x15
Warranty Card
x1
Recommended Tools
Personal & Vehicle Protection
Description
Safety Glasses
Safety Gloves
(Optional)
Vehicle Protection
Blankets, Parts Boxes
Special Tools
Techstream
Version 4.1 or later
Striker Tool
Recommended Sequence
of Application
Item#
Description
Installation Tools
Screwdriver
#2 Phillips, Flat Blade Jeweler’s
Nylon Panel Removal Tool
e.g. Panel Pry Tool #1 Toyota SST# 00002-06001-01
Side Cutters
1
TVIP V5 RS3200 plus
Torque Wrench
48 in•lbf (5.4 N•m)
2
TVIP V4 Remote Engine Starter
Tape
Clear, Electrical
Socket
10mm, extension
Special Chemicals
Issue: D 05/22/09
Cleaner
VDC Approved Cleaner
Glass Cleaner
Household Glass Cleaner
Page 1 of 35
TOYOTA PRIUS
2010–
PREPARATION
TVIP V5
RS3200 PLUS
Table of Contents
I. Preparation............................................................................................................................. 1 – 4
1. Table of Contents.................................................................................................................................................2
2. Wire Routing Overview.................................................................................................................................... 3-4
II. Procedure.............................................................................................................................5 – 2 7
1.
2.
3.
4.
5.
6.
7.
8.
9.
Hood Switch Installation. .....................................................................................................................................5
Disassembly (Driver’s Side). ...............................................................................................................................9
GBS ECU Preparation.......................................................................................................................................10
V5 Wire Harness Installation (Driver’s J/B Area)...............................................................................................12
V5 Wire Harness Installation (Driver’s Cowl Area)............................................................................................16
Registration Preparation....................................................................................................................................22
Registration........................................................................................................................................................24
Labels................................................................................................................................................................27
Completing the Installation. ...............................................................................................................................27
III. Checklist............................................................................................................................ 2 8 – 3 2
1. Accessory Function Checks. .............................................................................................................................28
2. Vehicle Function Checks. ..................................................................................................................................31
IV. Addendum I....................................................................................................................... 3 3 – 3 5
Legend
Do not proceed until process
has been completed.
Follow steps carefully to
avoid damaging the Vehicle
or Accessory
Use caution to avoid injury.
Used in Figures to call attention
to specific tools recommended
for the process.
Highlights a change in
installation with respect to
previous issue.
Accessory Installation Practice (read before installation)
Care must be taken when installing this accessory to ensure damage does not
occur to the vehicle. The installation of this accessory should follow approved
guidelines to ensure a quality installation.
These guidelines can be found in the “Accessory Installation Practices”
document.
This document covers such items as:
• Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.)
• Safety (eye protection, checking torque procedure, etc.)
• Vehicle Disassembly/Reassembly (panel removal, part storage, etc.)
• Electrical Component Disassembly/Reassembly (battery disconnection,
connector removal, etc.)
Please see your Toyota dealer for a copy of this document.
Indicates that torque is related
to safety.
Video available; click to play.
Issue: D 05/22/09
Page 2 of 35
Wire Harness Outline*
W
E
M
Description
A
OL1 26P White
B
OL1 26P White
C
OL2 12P White
D
OL2 12P White
8P White
(for GBS ECU)
E
-
J
L79
3P White
H
-
3P White
M
-
4P Black
N
-
Status Monitor
S
2D
Wire Terminal
(Green Wire)
W
-
GBS ECU
2010–
Page 3 of 35
S
Vehicle
TOYOTA PRIUS
TVIP
PREPARATION
Issue: D 05/22/09
PRIUS RS3200 plus
N
H
C
J
D
A
TVIP V5
*Color of Harness on Overview corresponds with Colored Tape near Connectors on Harness.
RS3200 PLUS
B
Y
Wire Harness Outline*
Description
A47 Jumper Connector
2010–
Page 4 of 35
Y
Vehicle
TOYOTA PRIUS
TVIP
PREPARATION
Issue: D 05/22/09
PRIUS RS3200 plus
TVIP V5
RS3200 PLUS
TOYOTA
PRIUS
2010–
TVIP V5
RS3200 PLUS
PROCEDURE
Disassembly Overview
3
1
3
2
6
1
Rear Board
2
Rear Box
3
Rear Trim
4
DS Step Cover
5
DS Cowl Cover
6
Lower Dash Cover
7
Lower Steering Column
Cover
7
5
4
Disconnect all Corresponding
Connectors.
Fig. 1-1
1. Hood Switch Installation.
a. Place the Vehicle in Park with
the Parking Brake set.
b. Remove the Rear Board.
Issue: D 05/22/09
Page 5 of 35
TOYOTA
PRIUS
2010–
PROCEDURE
Fig. 1-2
10mm Wrench
TVIP V5
RS3200 PLUS
c. Remove the Rear Box.
Fig. 1-3
d. Remove the Rear Trims to
gain access to the Battery.
1-4
Fig. 1-3
e. Disconnect the Negative
Battery Terminal.
• Note the Battery Cable Position
as it will be re-installed in the
same position.
CAUTION: Do not touch the
Positive Terminal.
f. Swap the Bolt and Nut on the
Negative Battery Terminal
from one side to the other for
easier installation.
Issue: D 05/22/09
Page 6 of 35
TOYOTA
PRIUS
2010–
TVIP V5
RS3200 PLUS
PROCEDURE
Check if Hood Switch is installed
NO
YES
WITH
Hood Switch
WITHOUT
Hood Switch
(Go to Next Section on Page 9)
Fig. 1-5
Vehicles Without
Hood Switch ONLY
g. Dislodge the Radiator Hose
to gain access to the Hood
Lock Assembly.
Issue: D 05/22/09
Page 7 of 35
TOYOTA
PRIUS
2010–
TVIP V5
RS3200 PLUS
PROCEDURE
Fig. 1-6
Fig. 1-7
Side Cutters
Without Hood Switch
Vehicle ON ONLY
h. Remove the tape securing
Hood Switch Pre-Connector.
i.
Connect the Jumper
Connector.
j.
Use 1 Wire Tie to secure the
Hood Switch Connectors.
Fig. 1-8
k. Reinstall the Radiator Hose.
Issue: D 05/22/09
Page 8 of 35
TOYOTA
PRIUS
2010–
TVIP V5
RS3200 PLUS
PROCEDURE
Fig. 2-1
Nylon Panel Removal Tool
2. Disassembly.
(Driver’s Side)
a. Remove the Driver’s Side
Step Cover.
Fig. 2-2
Nylon Panel Removal Tool
b. Remove the Driver’s Side
Cowl Cover.
• Remove 1 Nut.
Fig. 2-3
Nylon Panel Removal Tool, Phillips Screwdriver
c. Remove the Lower Dash
Cover.
• Remove 1 Screw.
d. Wrap the Lower Dash Cover
in a blanket and place on the
floor.
Issue: D 05/22/09
Page 9 of 35
TOYOTA
PRIUS
2010–
PROCEDURE
Fig. 2-4
TVIP V5
RS3200 PLUS
e. Dislodge the Steering
Column’s Center Clip.
CAUTION: Do not force this clip
as it is very easy to break.
Nylon Panel Removal Tool, Flat Blade Jeweler’s Screwdriver,
Electrical Tape
Fig. 2-5
f. Release the Back Clips on
both sides.
g. Release the Front Clips on
both sides.
• Turn the Steering wheel from
Right to Left to access the Holes.
• Use a Flat Blade Jeweler’s Screwdriver wrapped with Electrical
Tape to release the clips.
Fig. 3-1
10mm Socket
3. GBS ECU Preparation.
V5/V4 ADD-ON ONLY
a. Dislodge the RES ECU and
GBS Bracket.
• Remove 1 Bolt and Washer.
CAUTION: Do not drop the Bolt
and Washer.
b. Disconnect RES Connector.
c. Discard the GBS Bracket.
Issue: D 05/22/09
Page 10 of 35
TOYOTA
PRIUS
2010–
PROCEDURE
Flat Blade Jeweler’s Screwdriver
Issue: D 05/22/09
Page 11 of 35
TVIP V5
RS3200 PLUS
Fig. 3-2
d. Install the GBS Bracket from
the Kit to the GBS ECU.
Fig. 3-3
e. Attach 1/2 Piece of Foam
Tape to GBS ECU.
Fig. 3-4
f. Set the GBS sensitivity value
to “5”.
TOYOTA
PRIUS
2010–
PROCEDURE
Fig. 4-1
TVIP V5
RS3200 PLUS
4. V5 Wire Harness Installation. (Driver’s J/B Area)
a. Disconnect the Vehicle
Connectors on the right side
of the Junction Box.
Fig. 4-2
b. Disconnect the 36P Vehicle
Connector.
• Release Black Connector Lever.
Example
Fig. 4-3
Flat Blade Jeweler’s Screwdriver
c. Using a Flat Blade Jeweler’s
Screwdriver remove the Connector’s Black Lever.
CAUTION: Do not force the
Lever.
d. Lift up the Terminal Retainer
Clip.
CAUTION: Do not pull out the
Retainer.
Issue: D 05/22/09
Page 12 of 35
TOYOTA
PRIUS
2010–
PROCEDURE
Fig. 4-4
TVIP V5
RS3200 PLUS
e. Insert the V5 Green Wire
Terminal into the indicated
location on the 36P Vehicle
Connector.
• Close the Terminal Retainer Clip.
VERIFY: Terminal Pins are
properly inserted and do not
come out.
WIRE SIDE
Fig. 4-5
4-2
f. Re-attach the Connector’s
Black Lever.
g. Reconnect the Vehicle
Connectors.
Example
Example
Issue: D 05/22/09
Page 13 of 35
TOYOTA
PRIUS
2010–
PROCEDURE
Fig. 4-6
10mm Socket
TVIP V5
RS3200 PLUS
V5 ONLY
h. Install GBS ECU using the
Bolt and Washer from the Kit.
CAUTION: Do not drop the Bolt
and Washer.
Issue: D 05/22/09
Page 14 of 35
TOYOTA
PRIUS
2010–
TVIP V5
RS3200 PLUS
PROCEDURE
Fig. 4-7
10mm Socket
V5/V4 ADD ON ONLY
i.
Attach RES Bracket to the
GBS Bracket.
j.
Install the GBS ECU with
RES Bracket using the Bolt
and Washer from the Kit.
CAUTION: Do not drop the Bolt
and Washer.
k. Connect the V4 24P Connector to the RES ECU.
Fig. 4-8
Side Cutters
l.
Connect the V5 8P Connector to the GBS ECU.
m. Secure the V5 Harness to
Vehicle Harness with 2 Wire
Ties.
n. Secure the V5 5P BLACK
Connector as shown using
1 Wire Tie.
Issue: D 05/22/09
Page 15 of 35
TOYOTA
PRIUS
2010–
TVIP V5
RS3200 PLUS
PROCEDURE
Fig. 4-9
Side Cutters
o. Dislodge the Vehicle’s
Harness Shielding.
• Release 1 Clip.
p. Route the V5 Harness along
the Vehicle Harness towards
the Driver’s Cowl Area.
q. Reinstall the Vehicle’s Harness Shielding.
r. Secure the V5 Harness to
Vehicle Harness Shielding
with 1 Wire Tie.
Fig. 5-1
Side Cutters
5. V5 Wire Harness Installation. (Driver’s Cowl Area)
a. Secure V5 Harness to Vehicle Harness with 1 Wire Tie.
Fig. 5-2
Issue: D 05/22/09
Page 16 of 35
V5 ONLY
b. Connect the V5 3P Connector to the Vehicle’s 3P PreConnector.
TOYOTA
PRIUS
2010–
PROCEDURE
Side Cutters
Issue: D 05/22/09
Page 17 of 35
TVIP V5
RS3200 PLUS
Fig. 5-3
c. Use 2 Wire Ties to secure the
V5 3P Connectors as shown.
Fig. 5-4
d. Disconnect the Vehicle’s
White 12P Connector.
Fig.5-5
e. Plug the V5 12P Connectors
in between the Vehicle’s
Connectors.
TOYOTA
PRIUS
2010–
TVIP V5
RS3200 PLUS
PROCEDURE
Side Cutters
Fig. 5-6
f. Disconnect the Vehicle’s 26P
Connector.
Fig.5-7
g. Plug the V5 26P Connectors
in between the Vehicle’s
Connectors.
Fig. 5-8
h. Use 1 Wire Tie to secure the
V5 26P Connectors to the
Vehicle Harness.
i.
Issue: D 05/22/09
Page 18 of 35
Use 1 Wire Tie to secure
the V5 12P Connector to the
Vehicle Harness.
TOYOTA
PRIUS
2010–
TVIP V5
RS3200 PLUS
PROCEDURE
Fig. 5-9
Side Cutters
Fig. 5-10
V5/V4 ADD-ON ONLY
j.
k. Disconnect the V4’s and
Vehicle’s 3P Connectors.
l.
Fig. 5-11
Issue: D 05/22/09
Page 19 of 35
Cut 2 Wire Ties securing the
V4 Harness.
Connect the V5 3P Connectors in between the V4’s and
the Vehicle’s 3P Connectors.
m. Disconnect the Vehicle’s
and V4’s 12P Connectors.
TOYOTA
PRIUS
2010–
PROCEDURE
Issue: D 05/22/09
Page 20 of 35
TVIP V5
RS3200 PLUS
Fig. 5-12
n. Plug the V5 12P Connectors
in between the V4’s and the
Vehicle’s Connectors.
Fig. 5-13
o. Disconnect the Vehicle’s and
V4’s 26P Connectors.
Fig. 5-14
p. Plug the V5 26P Connectors
in between the V4’s and the
Vehicle’s Connectors.
TOYOTA
PRIUS
2010–
PROCEDURE
Fig. 5-15
Fig. 5-16
TVIP V5
RS3200 PLUS
q. Apply 1 Piece of Foam Tape
to the metal edge of the
opening above the Driver’s
Cowl Connector Block.
r. Secure the V4 26P Connector to the Vehicle’s Harness
with 1 Wire Tie.
• You may need to pull some of the
Vehicle Harness out of the Pillar.
DON’T FORCE THE HARNESS.
s. Push the V4 26P Connector
and Vehicle Harness back
into the opening in the Pillar.
Fig. 5-17
t. Secure the V5 26P Connector to the Vehicle’s Harness
with 1 Wire Tie.
u. Secure the V4 and V5 12P
Connectors to the Vehicle’s
Harness with 1 Wire Tie.
Issue: D 05/22/09
Page 21 of 35
TOYOTA
PRIUS
2010–
PROCEDURE
Fig. 6-1
TVIP V5
RS3200 PLUS
6. Registration Preparation.
a. Using VDC approved cleaner
and cleaning method, clean
the area indicated on the
Lower Dash Cover.
b. Attach 2 Foam Tapes as
shown.
c. Replace Knockout Panel with
the V5 Status Monitor.
Fig. 6-2
Side Cutters
d. Connect the V5 4P Connector to the V5 Status Monitor.
e. Reinstall the Lower Dash
Cover.
• Reconnect the Vehicle’s Connectors.
Issue: D 05/22/09
Page 22 of 35
TOYOTA
PRIUS
2010–
TVIP V5
RS3200 PLUS
PROCEDURE
Fig. 6-3
Phillips Screwdriver
Already
Installed
Do not Install
f. Reassemble the Vehicle.
Note: Make sure that all Connectors are reconnected.
Note: Verify that panels fit
together properly, with no uneven
gaps.
Fig. 6-4
g. Verify that the Short Pin is
Installed.
• If not Install now.
Fig. 6-5
10mm Socket
h. Temporarily reconnect the
Negative Battery Cable.
CAUTION: Do not touch the
Positive Terminal.
Issue: D 05/22/09
Page 23 of 35
TOYOTA
PRIUS
2010–
TVIP V5
RS3200 PLUS
PROCEDURE
Fig. 7-1
Techstream
7. Registration.
a. Connect the Techstream
Notebook to the Vehicle’s
Diagnostic Port.
b. With the Smart Key in your
possession, press the Power
Button twice to select the
Ignition “ON” position.
Fig. 7-2
c. Start the TIS Techstream
Application by clicking on
the shortcut located on the
Desktop.
d. Click “Connect to Vehicle.”
Fig. 7-3
e. Confirm that the information
displayed on the Vehicle
Connection Wizard is correct
for the vehicle. If not, verify
that the Techstream is properly connected.
f. Select w/Smart Key.
g. Click “Next>.”
Issue: D 05/22/09
Page 24 of 35
TOYOTA
PRIUS
2010–
TVIP V5
RS3200 PLUS
PROCEDURE
Fig. 7-4
Fig. 7-5
h. Click “Customize Setting.”
i.
Click
j.
Make sure that the “Customize” tab is selected.
.
k. Select “Option Setup.”
l.
Click
.
NOTE: If no “Option Setup” ONLY
If during this step you do not
see “Option Setup” as an option, please proceed to Addendum I (pg. 33).
Fig. 7-6
Issue: D 05/22/09
Page 25 of 35
m. Select “ON.”
n. Click
.
TOYOTA
PRIUS
2010–
TVIP V5
RS3200 PLUS
PROCEDURE
Fig. 7-7
Fig. 7-8
Fig. 7-9
Issue: D 05/22/09
Page 26 of 35
o. Click “Next” to accept the
changes to the Vehicle.
p. Click
.
q. Click “Close.“
TOYOTA
PRIUS
2010–
TVIP V5
RS3200 PLUS
PROCEDURE
Fig. 8-1
Clear Tape
10 mm
8. Labels.
a. Use Household Glass
Cleaner to clean the inside
of the Front Door Windows.
b. Use a piece of Clear Tape to
lift the Label off its protective
backing.
NG
HI
C
LS
ET
BE
E
A
L
TH
ER
H
TO
N
OT
IG
TO
AL
N
TO
LIG
A
W
HO
TO
W
O
H
CAUTION: Do not touch the
adhesive surface.
1– 5 mm
c. Attach the Label as shown.
NOTE: Make sure to Align
according to Etching or Other
Label.
REPEAT: steps a–c with the
other Window.
Fig. 9-1
Torque Wrench
9. Completing the
Installation.
a. Position the Negative Battery
Cable at the original factory
position.
• Tighten the Nut to 48 in•lbf
(5.4 N•m).
CAUTION: Do not touch the
Positive Terminal.
b. Finish reassembling the
Vehicle.
Fig. 9-2
VERIFY: That panels fit together
properly, with no uneven gaps.
VERIFY: That all Connectors are
plugged in.
c. Clean up and Remove trash.
d. Sealed in its protective bag,
place the Owner’s Manual in
the Glove box.
e. Reset the power windows.
Already
Installed
• Turn the ignition “ON.”
• Lower the Windows halfway.
• Pull up on the Power Window
Switches until the windows close.
• Continue to hold up on the
switches for a minimum of 1
Second.
Issue: D 05/22/09
Page 27 of 35
TOYOTA
PRIUS
2010–
CHECKLIST – these points MUST be checked to ensure a quality installation.
TVIP V5
RS3200 PLUS
Accessory Function Checks
1
Procedure
Look for:
Press and release the remote control’s lock button to start the system’s arming process.
The turn signal lights flash once
All doors lock.
The Security LED lights up.
2
Wait 30 seconds.
Security LED stops flashing; the system is now armed.
3
Press and release the remote control’s unlock
button to disarm the system.
The turn signal lights flash twice.
The driver’s door unlocks.
The Security LED flashing.
Open the driver’s door, with the smart key in your possession, press the power button to “ON”. Roll down all the windows, remove the key and exit the vehicle.
4
Arm and disarm the system with the remote
again, then wait 60 seconds.
The doors automatically re-lock.
The system automatically starts the arming process.
5
Press and release the remote control’s unlock
button again to stop the arming process.
Refer to step 3.
6
Press the lock button on the driver’s exterior
door handle to start the arming process.
All doors lock.
The Security LED lights up.
7
Wait 30 seconds.
Security LED stops flashing; the system is now armed.
8
Reach inside and manually unlock the driver’s
door to trigger an alarm.
The driver’s door automatically re-locks.
The horn sounds repeatedly.
The headlights flash repeatedly.
The turn signal lights flash repeatedly.
The Security LED lights up.
9
Manually unlock the driver’s door again and hold
it unlocked, open the door, then sit in the driver’s
seat.
The driver’s door lock attempts to lock repeatedly.
The horn continues to sound repeatedly.
The headlights and turn signal lights continue flashing.
The Security LED remains on.
10
The smart key in your possession, press the
power button twice on the dash to “START” to
stop the alarm.
The horn stops sounding.
All the lights stop flashing and/or turn off.
The Security LED turns off.
The starter cranks and the engine starts.
Issue: D 05/22/09
Page 28 of 35
TOYOTA
PRIUS
2010–
CHECKLIST – these points MUST be checked to ensure a quality installation.
TVIP V5
RS3200 PLUS
Press the “START” button to turn the vehicle off, and then exit the vehicle.
11
With the door open, press the lock switch on the
door to lock the doors, then close the door to
start the system’s arming process.
All doors lock.
The Security LED lights up.
12
Wait 30 seconds.
SECURITY LED stops flashing; the system is now
armed.
13
Reach inside and manually unlock the front passenger’s door to trigger an alarm.
The front passenger’s door automatically re-locks.
The horn sounds repeatedly.
The headlights flash repeatedly.
The turn signal lights flash repeatedly.
The SECURITY LED lights up.
14
Press and release the remote control’s unlock
button to stop the alarm.
The horn stops sounding.
All the lights stop flashing.
The Security LED flashing.
15
Press and release the remote control’s lock button to start the system’s arming process, then
wait 30 seconds until the system is armed.
Refer to steps 1 and 2.
16
Unlock and open one of the rear passenger
doors to trigger an alarm. (if available).
Refer to step 13.
17
Press and release the remote control’s unlock
button to stop the alarm.
Refer to Step 14
18
Repeat the above steps with the other rear passenger door. (if available).
Refer to steps 1, 2, and 13.
Roll up all windows, remove the key and exit the vehicle.
Take the Smart Key and the Smart Card Key away from the Vehicle. Place them 7ft. (2 meters) or more away from the
Vehicle.
19
Press and release the remote control’s lock button to start the arming process.
Refer to step 1.
20
Wait 30 seconds.
After 30 seconds, the Security LED stops flashing; the
system is now armed.
Issue: D 05/22/09
Page 29 of 35
TOYOTA
PRIUS
2010–
CHECKLIST – these points MUST be checked to ensure a quality installation.
TVIP V5
RS3200 PLUS
Perform the following check in a temperature-controlled environment. (50°-90° F)
21
With the tip of a key, or Striker Tool pulled all the
way out (PPO only), tap the center of the driver’s
door window to trigger the alarm.
The horn sounds repeatedly.
The headlights flash repeatedly.
The turn signal lights flash repeatedly.
The Security LED lights up.
22
Press and release the remote control’s unlock
button to stop the alarm.
Refer to Step 14
NOTE: If the alarm does not trigger during functional verifications, the Smart Key and Smart Card Key might be too close.
Move them farther away from the vehicle and test the system again.
NOTE: If the alarm does not trigger during functional verifications, increase the GBS sensitivity to the next setting.
NOTE: If you do not disarm the system, the alarm will last 20 seconds. It is not necessary to check the alarm duration.
Issue: D 05/22/09
Page 30 of 35
TOYOTA
PRIUS
2010–
CHECKLIST – these points MUST be checked to ensure a quality installation.
TVIP V5
RS3200 PLUS
Vehicle Function Checks
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
Function
Head Lights
High Beams
Turn Signal Lights
Tail Lights
Stop Lights
Backup Lights
Hazard Lights
Marker Lights
Dome/Courtesy Lights
Panel/Switch Illumination
Accessory Controls/Illumination
(if equipped)
Key Sensor Buzzer
Fog Lights (if equipped)
Daytime Running Lights (if equipped)
Trunk/Tailgate/Bed Lights (if equipped)
Glove Box Light (if equipped)
Cruise Control Light (if equipped)
Seat Belt Warning Light
If the warning light remains on, it may indicate a system malfunction.
Issue: D 05/22/09
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
Function
ABS Light (if equipped)
If the warning light remains on, it may indicate a
system malfunction.
Rear Wiper/Washer (if equipped)
Clock (if equipped)
Accessory Power Socket (if equipped)
Starter
Audio/Video (if equipped)
Power Sliding Door (if equipped)
Convenience Memory Settings (if equipped)
Heated Seats (if equipped)
Massage Seats (if equipped)
Rear Window Defogger (if equipped)
Power Side Mirrors (if equipped)
Side Mirror Defogger (if equipped)
Front Windshield Defogger (if equipped)
Navigation System (if equipped)
Rear Sunshade (if equipped)
Steering Wheel Audio Control (if equipped)
Steering Wheel Column Adjusts Without Interference
Page 31 of 35
TOYOTA
PRIUS
2010–
CHECKLIST – these points MUST be checked to ensure a quality installation.
□
□
□
□
□
□
□
□
□
□
Function
Air Bag Warning Light
If the warning light remains on, it may indicate
a system malfunction.
Track/Skid Control Light (if equipped)
If the warning light remains on, it may indicate
a system malfunction.
HVAC
Power Locks (if equipped)
Power Windows (if equipped)
Power Seats (if equipped)
□
□
□
□
□
□
Function
Lamp Failure Sensor
If the warning light remains on, it may indicate a
system malfunction.
Front Wiper/Washer
Hood Latch Release
Passenger Air Bag Switch (if equipped)
Rollover Side Curtain Air Bag Switch (RSCA)
(if equipped)
Tire Pressure Monitoring System (TPMS).
Prior to TPMS activation and Pre-delivery Service
(PDS) of the Vehicle the TPMS light will blink when IG
is turned on.
Power Moon/Sun Roof (if equipped)
Horn
After TPMS activation and PDS of the Vehicle the
TPMS light will illuminate for a few seconds and go off
when IG is turned on.
Gauges
Remote Air Conditioning system
Remove the short pin after Function check.
Check with your Port/Dealer to see if this step is necessary.
Issue: D 05/22/09
TVIP V5
RS3200 PLUS
Page 32 of 35
TOYOTA
PRIUS
2010–
TVIP V5
RS3200 PLUS
ADDENDUM I
Fig. 1-1
Techstream
1. Alternative Registration.
For Vehicles that did not
have an “Option Setup”
during normal Registration.
a. Connect the Techstream
Notebook to the Vehicle’s
Diagnostic Port.
b. With the Remote Control Key
in your possession, press the
Start Button to select either
“OFF” or the “ACC” position.
Fig. 1-2
c. Start the TIS Techstream
Application by clicking on
the shortcut located on the
Desktop.
d. Click “Connect to Vehicle.”
Fig. 1-3
e. Select “Toyota” for the Division.
f. Select “Prius” for the Model.
g. Select “2009” for the Model
Year.
CAUTION: You must select 2009.
h. Select w/Smart Key.
Issue: D 05/22/09
Page 33 of 35
i.
Make additional selection
based on the Vehicle Specifications.
j.
Click “Next>.”
TOYOTA
PRIUS
2010–
TVIP V5
RS3200 PLUS
ADDENDUM I
Fig. 1-4
Fig. 1-5
k. Click “Customize Setting.”
l.
Click
.
m. Make sure that the “Customize” tab is selected.
n. Select “Option Setup.”
o. Click
Fig. 1-6
Issue: D 05/22/09
Page 34 of 35
.
p. Select “ON.”
q. Click
.
TOYOTA
PRIUS
2010–
TVIP V5
RS3200 PLUS
ADDENDUM I
Fig. 1-7
Fig. 1-8
Fig. 1-9
r. Click “Next” to accept the
changes to the Vehicle.
s. Click
.
t. Click “Close.“
Go To Section 8 (Pg. 27)
Issue: D 05/22/09
Page 35 of 35
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement