P2110-EVB Rev B instructions

P2110-EVB
Evaluation Board for P2110 Powerharvester® Receiver
Description:
The P2110-EVB contains an evaluation board and antennas to test and develop with the P2110 Powerharvester
Receiver. The P2110 converts RF energy (radio waves) into DC power and stores it in a capacitor to provide an
intermittent, regulated voltage output.
Items included:
1 – Evaluation Board for P2110 Powerharvester Receiver (see description on next page)
1 – 915 MHz PCB dipole antenna (see description below)
1 – 915 MHz PCB patch antenna (see description below)
Note – this kit needs to receive power from an RF source such as a transmitter or test equipment.
Instructions:
1. Download the P2110 product datasheet from www.powercastco.com/resources to learn about the specific
I/O and functions of the P2110.
2. Connect one of the antennas to the SMA connector (J1) on evaluation board, or connect J1 directly to RF test
equipment. See datasheet for maximum input power.
3. Adjust switches S2, S3, and S4 to desired settings. See descriptions on next page.
4. Place evaluation board on flat surface and connect test meters as desired.
5. Turn on the source of RF energy (e.g. Powercast transmitter, test equipment, other transmitter)
Support:
Website:
Email:
Phone:
http://www.powercastco.com/resources/
contact@powercastco.com
+1 724-238-3700 (Eastern Time Zone – USA)
Item Descriptions
915 MHz PCB Dipole Antenna
This antenna is flat and has the RF connector located at the bottom of the antenna.
Type: omni-directional, vertically polarized
Energy pattern: 360°
Antenna gain: Linear gain = 1.25 (1.0 dBi)
915 MHz PCB Patch Antenna
This antenna has two layers and the RF connector located on the back of the antenna. The front side should be
pointed toward the transmitter with the same polarization
Type: directional, vertically polarized
Energy pattern: 122° (azimuth/horizontal), 68° (elevation/vertical)
Antenna gain: Linear gain = 4.1 (6.1 dBi)
P2110-EVB, Rev B 2010/9
© 2010 Powercast Corporation
Page 1
Evaluation Board
Component
S1
S2
S3
S4
C1
C2
C3
C4
C5
C6
JP1
D1
R1
R2
R4
R5, R6
BT1
J1
J2
U2
Description
Not used
Switch for output power
LED (power sent to illuminate LED D1)
MEAS (use with test points VOUT to LED or VOUT to STORE and in-line current meter)
VCC (power sent to test area and S4)
Switch for DSET selection. When enabled, RSSI is available through DOUT.
VOUT (Not used)
EXT (Enabled by external source through DSET EXT test point)
OFF (Normal charging operation)
Switch for powering external circuit through BT1 (BAT)
Optional output filtering for VOUT – 10 uF recommended (see datasheet)
Optional output filtering for RESET – 0.1 uF recommended (see datasheet)
Capacitor (1000 uF)
Capacitor (user selectable)
Capacitor (50 mF)
Not used
Selection for capacitors C3, C4, and C5
LED for visual indication of power output
Resistor for LED (D1)
Connection from VSET to GND to increase output voltage above 3.3V (see datasheet)
Connection from VSET to VOUT to decrease output voltage below 3.3V (see datasheet)
Not used
External circuit connection
SMA connector for antenna or RF input (add DC block for DC short antenna)
Connector for add-on boards
Connector on board: FCI – P/N: 52601-G10-8LF
Mating connector:
Sullins – P/N: SFH11-PBPC-D05-ST-BK
P2110 Powerharvester receiver (see datasheet for pin descriptions)
P2110-EVB, Rev B 2010/9
© 2010 Powercast Corporation
Page 2
P2110-EVB Electrical Schematic
P2110-EVB, Rev B 2010/9
© 2010 Powercast Corporation
Page 3
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Powercast:
P2110-EVB