MAXXFAN® - Airxcel

MAXXFAN
®
INSTALLATION INSTRUCTIONS,
INFORMATION AND OPERATING GUIDE
FOR ALL MAXXFAN® Deluxe MODELS
5100K, 5101K, 5301K, 6200K, 6201K, 6401K,
7000K, 7001K, 7500K, 7501K, 8000K, 8001K,
8500K, 8501K, 8700K, 8751K, 8900K, 8951K
READ AND SAVE THESE INSTRUCTIONS
NOTE: Refer to supplied Operating Instructions regarding the model you have purchased.
The MAXXFAN installs into a standard RV roof opening of 14” x 14”.
To determine if your roof opening is correctly sized, simply remove the interior ceiling garnish
trim ring of your existing roof vent and measure the ceiling opening or verify the opening is
large enough by sliding the MAXXFAN interior garnish trim ring into the opening.
Due to the EXHAUST / INTAKE LOUVERS that face the rear of the vehicle, the MAXXFAN
requires a roof area clear of obstructions such as air conditioners, storage boxes, etc. for at
least 8” to the rear of the existing standard roof vent flange outer rear edge.
The MAXXFAN is designed for a minimum roof thickness of 1 1/8” to a maximum of 6 1/2”.
If your roof thickness is less than 1 1/8”, build additional thickness at the ceiling opening
using wood or other suitable material.
The MAXXFAN requires a minimum 12 Volt DC, 5 amp service. Confirm that the circuit
you intend to use will accommodate the additional load. Use the proper gauge stranded
wire for electrical connections.
WARNING! To reduce risk of fire, injury to persons or damage to property, use only
in the manner intended by AIRXCEL, INC. Should you have questions, please contact
AIRXCEL/MAXXAIR VENTILATION SOLUTIONS Customer Service at 316.832.4357.
P/N: 11C90001K
07-2016
INSTALLATION INSTRUCTIONS - ALL MODELS
STEP 1
MAXXFAN requires a roof opening of 14” x 14”. If you
are replacing another type already installed, remove the
old existing roof vent. Remove all old roof sealant for a
minimum of 2” entirely around the roof opening.
showing (+) must be connected to the vehicle 12 volt (+)
positive supply.
STEP 4
Confirm the 4 metal mounting clips are firmly in place on
the Roof Receiving Flange. With the MAXXFAN open
and the exhaust/intake louvers facing the rear of the
vehicle, lower the MAXXFAN onto the Roof Receiving
Flange.
Make sure the power wires slide to the vehicle interior
and do not become entangled on the Roof Receiving
Flange’s upward edge.
Place the MAXXFAN Roof Receiving Flange (reference
photo #2 below) into the roof opening and trace a pencil
line around it to verify the clean seal area that will be
required. Note that the Roof Receiving Flange must be
centered in the roof opening with the metal clips facing
the sides of the vehicle (not facing the front or rear of the
vehicle).
CAUTION: When installing your Roof Flange, only
use a caulking/sealant compatible with the flange
(plastic product) and the roof surface.
DO NOT
use materials containing solvents such as or similar
to Xylene, Toluene, Methyl Ethyl Ketone, Acetate
or Acetone as they can damage the flange. Also,
Polysulfide (Thiokol) type sealants must be avoided.
Silicone Sealants such as G.E. Silicone II (nonpaintable) used for outdoor applications have proven
to be suitable for this installation.
METAL MOUNTING
CLIPS
4
If in doubt, please contact the manufacturer of your
RV for further information.
STEP 2
Apply Sealant or Caulking within the area you have traced
on the roof with a pencil. Apply it carefully to avoid gaps
that may allow water to enter.
Fasten the Roof Receiving Flange to the roof with
screws provided.
Apply additional roof sealant over the screw heads and
around the edge of the roof flange.
RECEIVING FLANGE
UPPER EDGE
STEP 5
Verify the MAXXFAN is fully seated down on the Roof
Receiving Flange and fasten the MAXXFAN to the Roof
Receiving Flange using the four 3/4” #10 stainless steel
screws provided.
CAUTION: Only use the screws provided/specified
for this installation or internal damage and/or insecure
mounting may result.
CAUTION: Disconnect main vehicle power before
connecting 12 volt DC power to the MAXXFAN!
NOTE: The MAXXFAN must be fully opened prior to
proceeding to STEP 3. Turn knob to fully raise the vent
lid.
NOTE: On the NON-REMOTE controlled models, the
knob must be pulled out to unlock before turning.
5
OPEN / CLOSE
KNOB
THIS COMPLETES THE ROOF TOP
PORTION OF THE INSTALLATION
ROOF FLANGE
2
STEP 3
Using the insulated electrical connectors provided,
connect the vehicle’s 12 volt power to the two
MAXXFAN power wires located on the driver side of
the MAXXFAN.
NOTE: The MAXXFAN black wire identified with a tag
2
NOTE: Re-apply 12 volt vehicle power. The MAXXFAN,
excluding the 5301K and 6401K, will emit a beeping sound
to indicate power is properly connected.
In addition, the
Remote Control model will automatically close the vent cover.
If the MAXXFAN does not beep when power is connected,
go back to step #3. Confirm that proper connections were
made and 12 volt power is on and available. This MAXXFAN
incorporates a self-resetting fuse on the circuit board located
in the ceiling assembly. It can be reset by removing and reapplying power. If your fan fails to operate or needs reset,
contact Customer Service at 316.832.4357 for assistance or
solicit the aid of an electrical technician.
STEP 6
The interior Garnish Trim Ring must be trimmed to fit
your particular RV roof thickness. To accomplish this,
measure the distance from the vehicle ceiling surface to
each corner of the MAXXFAN Control Plate.
Most RV roofs have some slope, so measuring each
corner is necessary. The Garnish ring should be cut
1/4” to 1/2” longer than the dimensions measured at
each corner.
In Picture #6 below, the installation measures 3 1/2”
from the ceiling (this is an example only) to the Control
Plate. After adding 1/2” as in this example, using a ruler,
place a mark at 4” on each corner of each side of the
Garnish Ring (refer to 6A, right). Once marked, draw a
line connecting all 4” marks on the outside of the Garnish
ring and trim accordingly (refer to 6B, right).
6A
GARNISH RING
THERMOSTAT
SENSOR
6B
3 1/2”
6
GARNISH RING
MEASUREMENTS STATED IN STEP
6 ARE USED AS AN EXAMPLE FOR
ILLUSTRATION PURPOSES ONLY
CEILING
NOTE: DO NOT probe or tamper with the thermostat
sensor or IR sensor shown in illustration #6 above.
7
STEP 7
Complete the installation by placing any excess wiring
to the inside of the roof opening and sliding the Garnish
Ring into position. Fasten in place by using the four
painted flat head screws provided.
CONGRATULATIONS!!!
You have successfully completed the
installation of your new
MAXXFAN Deluxe.
If you have questions, please visit
AIRXCEL.com or contact
Customer Service at 316.832.4357.
3
FOR REMOTE CONTROL MODELS: Refer to
the Operating Instructions for use and testing of your
remote control.
Install two AAA batteries, follow
instructions, aim remote at the ceiling unit and test
your fan. The Remote Control comes with a cradle
for wall mount storage of the Handheld Remote
Control. Mount the cradle to your wall using the (2)
#6 screws provided. Remote may be placed into the
wall cradle for storage.
MAXXFAN® 2 YEAR LIMITED WARRANTY
AIRXCEL, INC. - RV PRODUCTS DIVISION / MAXXAIR RETAINING KNOB SERIAL NUMBER
Ventilation Solutions warrants to be free of manufacturing
defects, regardless of ownership for a period of two (2) years
from the original date of purchase. If the product is installed as
original equipment on a vehicle, the warranty period shall begin
on the date of the original purchase of the vehicle. In all other
instances, the warranty shall begin on the date the product
was purchased. You must keep your original sales receipt.
This Limited Warranty does not include “Acts of God,” failure
due to misuse, improper installation or accidental / incidental
damages. Please call AIRXCEL, INC. at 1-316-832-4357 if you have any questions or
need assistance.
Please have your original sales receipt and MAXXFAN Serial Number readily
available.
AIRXCEL will correct the confirmed defect within 45 days by repair or
replacement without charge for materials and labor. This limited warranty does not cover
any freight costs for the return of the product to or from AIRXCEL, INC. or costs associated
with installation, removal or reinstallation of the product.
We invite your comments and suggestions regarding our products. Any information you
supply is for AIRXCEL / MAXXAIR’s internal use and will not be shared or sold to others.
The Serial Number for your MAXXFAN is located on the back page of this booklet and on the fan
control plate under the round insect screen frame. (Your serial number may or may not be located in
the same position as referenced in the above image). Reference your operating guide. Rotate the
four retaining knobs 180° and remove the screen to view. DO NOT OPERATE the MAXXFAN with
the screen removed.
CAUTIONS AND CARE OF YOUR MAXXFAN®
This product has been manufactured using prime UV stabilized Polymers for maximum
toughness and durability. However, the use of caustic or solvent based chemicals can
cause cracking and product failure.
PLEASE CLEAN ALL PARTS WITH MILD SOAP AND WATER ONLY.
Do not use Petroleum Containing Additives or Solvent Based Products on any of the
MAXXFAN’s components or its corrosion resistant hardware.
LISTED BELOW ARE SOME KNOWN CHEMICAL PRODUCTS TO BE
AWARE OF:
NON COMPATIBLE CHEMICALS - DO NOT USE THESE:
Ketones, Esters, Acetone or other like solvents, Halogenated Hydrocarbons,
Amines, Aromatic Hydrocarbons, (Loctite Formulas), or any products containing
references to: chemicals that are not to be used on plastics.
GENERALLY COMPATIBLE (But should be used in low concentration
where possible)
Acids, Alcohol, Alkalis, Aliphatic Hydrocarbons, Mild Soap Solution (avoid strong
Alkaline Material), Silicone Oil or Greases (avoid those containing Aromatic
Hydrocarbons or other additives). Review the contents of your cleaning materials
carefully.
For additional information regarding your NEW MAXXFAN® Deluxe,
please refer to the INFORMATION AND OPERATION GUIDES
FOR YOUR PARTICULAR MODEL ON THE FOLLOWING PAGES.
4
INFORMATION AND OPERATING GUIDE
KEYPAD FOR MAXXFAN® Deluxe MODELS
5301K • 6401K
KNOB, VENT LID OPEN/CLOSE
Manual Opening
Pull to unlock prior to turning. Rotate Knob
clockwise to Close Vent Lid; Rotate Knob
counter-clockwise to Open Vent Lid. Push
“IN” to lock when Vent Lid is open or closed.
It may be necessary to slightly rotate the
knob to properly align it while pushing it up
to lock.
Do not use excessive force when operating
Knob.
KEYPAD CONTROLS
Use Keys on Keypad to control MAXXFAN
functions (see descriptions below).
INSECT SCREEN RETAINER KNOB
Rotate all 4 knobs 1/2 turn to remove screen.
Caution: Never operate fan with screen removed.
CEILING FAN MODE
With the fan motor running, close the Vent Lid to enter Ceiling Fan Mode. The fan motor will
continue to run and circulate air within the RV cabin.
SERIAL NUMBER LABEL
The serial number label is located underneath the round insect screen.
NOTE: The MAXXFAN is designed to be fully opened or fully closed when the vehicle is moving.
KEYPAD CONTROLS
KEYPAD FOR MAXXFAN® Deluxe MODELS
5301K • 6401K
CAUTION: When removing insect screen for cleaning, turn the MAXXFAN OFF and remove the vehicle
12 volt power to the MAXXFAN. When cleaning your MAXXFAN, use only a mild detergent solution.
FAN ON
1-2-3-4
Turns the Fan Motor ON to the last
selected speed
When the fan is running, cycles
through four (4) speeds, once HIGH
FAN ON SPEED is reached, fan motor cycles
1-2-3-4 back to LOW SPEED
FAN
OFF
Turns the Fan Motor OFF at any
selected speed
5
FAN
OFF
INFORMATION AND OPERATING GUIDE
KEYPAD FOR MAXXFAN® Deluxe MODELS
5100K, 5101K, 6200K, 6201K, 7000K, 7001K, 7500K, 7501K,
8000K, 8001K, 8500K, 8501K
KNOB, VENT LID OPEN/CLOSE
Manual Opening Models
Pull to unlock prior to turning. Rotate Knob
clockwise to Close Vent Lid; Rotate Knob
counter-clockwise to Open Vent Lid. Push
“IN” to lock when Vent Lid is open or closed.
Automatic Opening Models
Allows closing of the vent lid in the event
of RV power loss. This knob does not
lock. Do not push in or pull out. Rotate
knob clockwise to close vent lid; rotate knob
counter-clockwise to open vent lid.
Do not use excessive force when operating
Knob.
KEYPAD CONTROLS
Use Keys on Keypad to control
MAXXFAN functions
(see descriptions on next page).
NOTE: IR Sensor not on all models
INSECT SCREEN RETAINER KNOB
Rotate all 4 knobs 1/2 turn to remove screen.
Caution: Never operate fan with screen removed
THERMOSTAT TEMPERATURE SENSOR
CEILING FAN MODE
With the fan motor running, close the Vent Lid to enter Ceiling Fan Mode. The fan
motor will continue to run and circulate air within the RV cabin.
SERIAL NUMBER LABEL
The serial number label is located underneath the round insect screen.
NOTE: The MAXXFAN is designed to be fully opened or fully closed when the
vehicle is moving.
CAUTION: When removing screen for cleaning, turn the MAXXFAN OFF
and remove the vehicle 12 volt power to the MAXXFAN. When cleaning your
MAXXFAN, use only a mild detergent solution.
6
KEYPAD CONTROLS KEYPAD CONTROLS
KEYPAD FOR
MAXXFAN® Deluxe
INTAKE/EXHAUST MODELS
5100K, 6200K, 7000K, 7500K,
8000K, 8500K
KEYPAD FOR
MAXXFAN® Deluxe
EXHAUST ONLY MODELS
5101K, 6201K, 7001K, 7501K
8001K, 8501K
NOTE: A beeping sound will confirm each key press
ON/OFF: Use this key to start the fan or to turn off the fan. On Automatic Opening Models
the lid will also open or close when the fan is turned on or off. On Manual Opening Models
pushing this key while in Auto Mode will exit Auto Mode, turn off the fan and the lid will stay
in the position you selected. On Automatic Opening Models this button will exit Auto mode,
turn the fan off, and close the lid.
IN/OUT: Use this key to reverse the direction of the fan, the fan will slow down and pause
for two (2) seconds before resuming operation in the opposite direction. Note: In Auto
Mode the fan direction is automatically positioned to Exhaust, but may be overridden and
changed to Intake by depressing this key. PLEASE NOTE: THIS KEY HAS BEEN
REMOVED ON EXHAUST ONLY MODELS
AUTO: Auto Mode allows the thermostat to turn the fan ON and OFF depending on the
thermostat setting. Press this key once for less than three (3) seconds to enter Auto Mode,
three (3) quick beeps will confirm the MAXXFAN has entered Auto Mode. To EXIT Auto
Mode, press the ON/OFF key. Initial factory set point for the thermostat is 78°F/25°C. The green LED
will light to indicate the MAXXFAN is in Auto Mode. To adjust, follow instructions below:
If no previous thermostat temperature was entered, or you wish to change a previous set temperature,
press the HOLD TO SET key for more than 3 seconds and you will hear one long beep and the
thermostat will be reset to 78°F. To further adjust the set temperature, if desired, use the (+) or (-) Arrow
keys to adjust at 1° increments per press. The fan will emit a beeping sound to confirm this setting. If
a previous thermostat temperature was entered, the fan will remember this temperature setting and the
next time you enter Auto Mode, the fan will start ventilating automatically as directed by the thermostat.
The fan speed will automatically adjust based on the cabin temperature. As cabin temperature rises,
the fan increases in speed. Note: If 12 volt RV power is removed from the MAXXFAN, the thermostat
will be reset to 78°F/25°C.
ARROW - When in Auto Mode: Use the (+) & (-) Arrow keys to adjust the thermostat set
temperature up or down in 1° increments per press.
When in Manual Mode: Use the (+) & (-) Arrow keys to adjust the fan speed up or down.
When the fan speed reaches either the maximum or minimum speed, the fan will respond
with 2 quick beeps to indicate this.
ARROW KEYS PRESSED TOGETHER: Automatic Lift Models Only
Press the (+) & (-) Arrow keys at the same time to Open or Close the lid. The fan motor will remain in
its current state.
7
REMOTE CONTROL OPERATING GUIDE
WIRELESS REMOTE CONTROL FOR
MAXXFAN® Deluxe MODELS 7000K • 7500K
Optional for 8000K, 8500K, 8700K, 8900K Models
FAN ON & POWER OFF - Press this button:
• To start the fan
• To turn the fan off
• To exit Auto Mode
Remove protective film from
Display Screen
VENT LID POSITION - Press this button to open or close the vent lid
•While the fan is running in Manual Mode press once to close the vent lid and
enter “Ceiling Fan” Mode.
NOTE: This button is not active in Auto Mode. If the fan loses 12volt RV
power or power is removed from the fan, use the knob located at the ceiling
to manually open or close the vent lid if desired.
AIR EXHAUST / INTAKE - Press this button to reverse the fan from
intake or exhaust
NOTE: In Auto Mode, the fan direction is automatically positioned to Exhaust,
but may be overridden and changed to Intake by depressing this key.
FAN AUTO MODE - Press this button to enter Auto Mode
•Auto Mode allows the fan lid to automatically open and the fan motor to
operate as dictated by the thermostat set point temperature. Once the cabin
temperature cools and reaches the set point temperature, the fan lid will close
and the fan motor will shut off.
•Pressing this button while in Auto Mode will shut off Auto Mode, close the vent lid
and shut off the fan motor.
THERMOSTAT SET TEMPERATURE
TEMP + ~ Press this button to increase the Set Temperature for Auto Mode.
TEMP - ~ Press this button to decrease the Set Temperature for Auto Mode.
NOTE: The thermostat temperature range is from 29°F to 99°F or -2°C to 37°C. To change from Fahrenheit
to Celsius on the temperature display, press and hold both set temperature keys simultaneously.
FAN SPEED
Fan Speed + ~ Press
this button to increase
the fan speed. The fan
has ten speeds.
Fan Speed - ~ Press this
button to decrease the
fan speed. The fan has
ten speeds.
NOTE: When the fan
speed reaches either the
maximum or minimum
speed, the fan will
respond with 2 quick
beep sounds to indicate
this.
SET
TEMPERATURE
TRANSMIT
LOW BATTERY
INDICATOR
AUTO MODE
INDICATOR
ROOM
TEMPERATURE
FAN ON
INDICATOR
VENT LID IN
AUTO MODE
CEILING FAN
FAN OFF
INDICATOR
VENT LID
POSITION
FAN SPEED
CEILING FAN MODE
LOW BATTERY
INDICATOR
•When the battery is at full charge, three black power bars are displayed.
•One or zero power bars displayed indicates the batteries need replacement.
AIR DIRECTION
INDICATOR
TRANSMISSION SIGNAL
•This symbol is displayed on the screen when any button is pressed to indicate the signal was transmitted
to the fan.
•A beep sound from the ceiling unit indicates the signal from the remote control was received by the fan.
8
REMOTE CONTROL OPERATING GUIDE
WIRELESS REMOTE CONTROL FOR
MAXXFAN® Deluxe MODELS 7001K • 7501K
Optional for 8001K, 8501K Models
FAN ON & POWER OFF - Press this button:
• To start the fan
• To turn the fan off
• To exit Auto Mode
Remove protective film from
Display Screen
VENT LID POSITION - Press this button to open or close the vent lid
•While the fan is running in Manual Mode press once to close the vent lid and
enter “Ceiling Fan” Mode.
NOTE: This button is not active in Auto Mode. If the fan loses 12volt RV
power or power is removed from the fan, use the knob located at the ceiling
to manually open or close the vent lid if desired.
AIR OUT
FAN AUTO MODE - Press this button to enter Auto Mode
•Auto Mode allows the fan lid to automatically open and the fan motor to
operate as dictated by the thermostat set point temperature. Once the cabin
temperature cools and reaches the set point temperature, the fan lid will close
and the fan motor will shut off.
•Pressing this button while in Auto Mode will shut off Auto Mode, close the vent lid
and shut off the fan motor.
THERMOSTAT SET TEMPERATURE
TEMP + ~ Press this button to increase the Set Temperature for Auto Mode.
TEMP - ~ Press this button to decrease the Set Temperature for Auto Mode.
NOTE: The thermostat temperature range is from 29°F to 99°F or -2°C to 37°C. To change from Fahrenheit
to Celsius on the temperature display, press and hold both set temperature keys simultaneously.
FAN SPEED
Fan Speed + ~ Press
this button to increase
the fan speed. The fan
has ten speeds.
Fan Speed - ~ Press this
button to decrease the
fan speed. The fan has
ten speeds.
NOTE: When the fan
speed reaches either the
maximum or minimum
speed, the fan will
respond with 2 quick
beep sounds to indicate
this.
SET
TEMPERATURE
TRANSMIT
LOW BATTERY
INDICATOR
AUTO MODE
INDICATOR
ROOM
TEMPERATURE
FAN ON
INDICATOR
VENT LID IN
AUTO MODE
CEILING FAN
FAN OFF
INDICATOR
VENT LID
POSITION
FAN SPEED
CEILING FAN MODE
LOW BATTERY
INDICATOR
•When the battery is at full charge, three black power bars are displayed.
•One or zero power bars displayed indicates the batteries need replacement.
AIR DIRECTION
INDICATOR
TRANSMISSION SIGNAL
•This symbol is displayed on the screen when any button is pressed to indicate the signal was transmitted
to the fan.
•A beep sound from the ceiling unit indicates the signal from the remote control was received by the fan.
9
OPERATION GUIDE - 1-SWITCH WALL CONTROL
FOR USE WITH MAXXFAN® Deluxe MANUAL OPENING Models
5100K, 5101K, 5301K, 6200K, 6201K
OPERATION OF 1-SWITCH WALL CONTROL
FAN 1-2-3
When Fan is running, select LOW,
Turns the fan motor ON at the last
MEDIUM or HIGH Speed. Once
selected speed and OPENS the
HIGH Speed is reached, the fan
Vent Lid.
motor cycles back to LOW Speed.
FAN OFF
Turns the Fan Motor OFF
OPERATION GUIDE - 2-SWITCH WALL CONTROL
FOR USE WITH MAXXFAN® Deluxe ELECTRIC OPENING Models
7000K, 7001K, 7500K, 7501K, 8000K, 8001K, 8500K, 8501K
CONTROL
FAN 1-2-3
FAN OFF
VENT
OPEN
VENT
CLOSED
DESCRIPTION
When Fan is running, select
Turns the fan motor ON at LOW, MEDIUM or HIGH
the last selected speed and Speed. Once HIGH Speed is
OPENS the Vent Lid.
reached, the fan motor cycles
back to LOW Speed.
Turns the Fan Motor OFF and CLOSES the Vent Lid
OPENS the Vent Lid
Fan motor remains in previous
state
CLOSES the Vent Lid
Fan motor remains in previous
state. If fan motor is ON, the
MAXXFAN enters Ceiling Fan
Mode
OPERATION GUIDE - 4 KEY WALL CONTROL
FOR MAXXFAN® Deluxe Models 8751K • 8951K
OPTIONAL FOR MAXXFAN® Deluxe Models 5100K, 5101K, 5301K, 6200K, 6201K, 6401K
OPERATION OF 4 KEY WALL CONTROL
When Fan is running, cycles
Turns the fan motor ON at through four (4) fan Speeds.
FAN ON
the last selected speed and Once HIGH Speed is reached,
1-2-3-4 OPENS the Vent Lid.
the fan motor cycles back to LOW
Speed.
FAN ON
1-2-3-4
VENT
OPEN
FAN OFF
VENT
CLOSE
FAN
OFF
Turns the Fan Motor OFF and CLOSES the Vent Lid
VENT
OPEN
OPENS the Vent Lid
Fan motor remains in previous
state
VENT
CLOSE
CLOSES the Vent Lid
Fan motor remains in previous
state. If fan motor is ON, the
MAXXFAN enters Ceiling Fan
Mode
10
OPERATION GUIDE - 5 KEY WALL CONTROL
OPTIONAL FOR MAXXFAN® Deluxe Models 7001K • 7501K • 8001K • 8501K
OPERATION OF 5 KEY WALL CONTROL
FAN
ON/OFF
FAN
ON/OFF
Turns the fan motor ON at the last selected speed and
OPENS the Vent Lid. Turns the fan motor OFF and
CLOSES Vent Lid.
Pressing this key when in AUTO mode will cause the fan to
exit AUTO mode.
AUTO
Puts the fan in AUTOMATIC thermostat mode.
Vent lid will automatically open and fan will turn on to cool RV
when set temperature is reached. Once RV is cooled down,
fan will turn off and vent lid will close. Thermostat is set to last
selected temperature (memory function). Green LED will light
to indicate MAXXFAN is in AUTO mode. Hold key for three (3)
seconds to reset thermostat temperature to 78°F, use (+) & (-)
keys to adjust set temperature up or down. Press ON/OFF key
to exit AUTO mode.
OPEN/
CLOSE
Adjusts the fan speed or thermostat set temperature.
When fan is on in MANUAL mode: adjusts fan speed up or
down from 10% to 100% (10 speeds). When fan is in AUTO
mode: adjusts thermostat set temperature up or down by 1°F
per key press.
HOLD TO
SET 78°F
AUTO
OPEN/
CLOSE
OPENS and CLOSES the motorized Vent Lid.
Allows the vent lid to be open or closed with the fan motor on
or off. Close vent lid with fan motor running in Manual mode
to enter Ceiling Fan Mode.
OPERATION GUIDE 6 KEY WALL CONTROL
FOR MAXXFAN® Deluxe Models 8700K • 8900K
OPTIONAL FOR MAXXFAN® Deluxe Models 7000K, 7500K, 8000K, 8500K
OPERATION OF 6 KEY WALL CONTROL
FAN
ON/OFF
FAN
ON/OFF
Turns the fan motor ON at the last selected speed and
OPENS the Vent Lid. Turns the fan motor OFF and
CLOSES Vent Lid.
Pressing this key when in AUTO mode will cause the fan to
exit AUTO mode.
AUTO
Puts the fan in AUTOMATIC thermostat mode.
Vent lid will automatically open and fan will turn on to cool RV
when set temperature is reached. Once RV is cooled down,
fan will turn off and vent lid will close. Thermostat is set to last
selected temperature (memory function). Green LED will light
to indicate MAXXFAN is in AUTO mode. Hold key for three (3)
seconds to reset thermostat temperature to 78°F, use (+) & (-)
keys to adjust set temperature up or down. Press ON/OFF key
to exit AUTO mode.
OPEN/
CLOSE
Adjusts the fan speed or thermostat set temperature.
When fan is on in MANUAL mode: adjusts fan speed up or
down from 10% to 100% (10 speeds). When fan is in AUTO
mode: adjusts thermostat set temperature up or down by 1°F
per key press.
HOLD TO
SET 78°F
AUTO
IN / OUT
OPEN/
CLOSE
OPENS and CLOSES the motorized Vent Lid.
Allows the vent lid to be open or closed with the fan motor on
or off. Close vent lid with fan motor running in Manual mode
to enter Ceiling Fan Mode.
IN/OUT
Reverses fan motor for either INTAKE or EXHAUST air
direction.
11
. . . reinventing comfort!
PLACE CONSUMER LABEL HERE
For additional product information please visit www.AIRXCEL.com
AIRXCEL, INC. - RV Products Division / MAXXAIR
3050 N. St. Francis St. • Wichita, KS 67219 • 316.832.3400