Hovercraft pdf

Connecting Pegs
HOVERCRAFT — A vehicle able to travel over land or water on a cushion of air created
by a downward blast.
HOVERCRAFT
Please read manual before you begin! Failure to
follow this manual’s instructions may result in
damage to the Triangle Power base, AC adapter
and/or Laser Pegs®. Not adhering to these
directions will void the manufacturer’s warranty.
Packing has to be kept since it contains
important information.
870
For Boys And Girls
Ages 5 And Up
12 Models+
WARNING:
Any creation you can build
CHOKING HAZARD-Small parts.
LIGHTED
Press button
to turn on/off
Not for children under 3 yrs.
Do not submerge in water.
CONSTRUCTION SET INCLUDES:
To construct with Laser Pegs®, slide two pieces together to form a
connection. Slide each piece on and off smoothly. To build away from the
Triangle Power Base, use the peg cord in one of the top three peg holes to
illuminate your model! The 90° pegs are essential to construction but they
DO NOT ILLUMINATE.
Model
Difficulty
Level
Peg Holes
Power button
AC Adapter
Connection
Construction Compatible
Requires 3 AA Batteries
Connect Laser Pegs® TRIANGLE POWER BASE
Compatible with other construction kits
Batteries NOT
Included
EN71, RoHS COMPLIANT
Connect cord to model.
This product complies to
all safety requirements
of ASTM F 963
A
MODEL INSTRUCTIONS
STEP
4
All additional model instructions can
be downloaded at www.LaserPegs.com
To build away from the Laser Pegs®
Triangle power base use the peg
cord in one of the top three holes to
illuminate your model!
Laser Peg® Parts List
x6
x1
x4
x4
x2
SQUARE
PEG
45° PEG
90° PEG
Stackable
WHEEL PEG
Each Laser Peg® is color coded on the circuit board inside
each shape. There is No LED In The 90 Degree Peg.
Color
Code
Laser Pegs® Stackable
Laser Pegs® link that
Triangle Power
Base
allows you to connect to
other construction kits.
Laser Pegs®
Peg Cord
Construction Parts List
x1
x2
x6
x12
x2
x10
x6
x2
x3
x5
x5
x3
x1
x2
x4
www.LaserPegs.com
1. Remove screws.
2. Place three AA batteries in the correct
position - as displayed inside the Triangle Power Base.
3. Push RED button to turn on!
4. Do not mix old and new batteries.
5. Do not mix alkaline, standard (carbonzinc), or rechargeable (nickel-cadmium) batteries!
6. Exhausted batteries are to be removed
from the power base.
7. Never connect more than 200 Laser Pegs®
8. Non-rechargeable batteries are not to be recharged.
9. Rechargeable batteries are only to be charged under adult supervision.
10. Rechargeable batteries are to be removed
from the toy before being charged.
11. Batteries are to be inserted with the
correct polarity.
12. The supply terminals are not to be shortcircuited.
Using an
AC Adapter
Remove all batteries
from Laser Pegs® power
base before using the
5 volt AC adapter.
*To avoid short-circuits, keep metal objects and
other un-authorized materials from obstructing
the peg holes.
x4
x2
x2
When you remove a peg from another
peg or model DO NOT PULL ON CORD!
When Using Batteries
There is No LED In The 90 Degree Peg
Y PEG
3
Push button to cycle
through 3 different
light settings.
• 20 Laser Pegs®
• Triangle Power Base
• Instruction Manual
• 84 Construction parts
x3
STEP
x4
x6
x2
This manual is copyright and cannot be reproduced or used online without Laser
Pegs®Ventures LLC permission. Copyright 2012 © All Rights Reserved US Patent
#7,731,558 Additional Global & Multiple Patents Pending. Laser Pegs®Ventures
LLC. 8304 Consumer Ct Sarasota FL. 34240. Contact: Support@LaserPegs.com
STEP
1
STEP
Remove the three Philips head
screws with a 4mm screw driver.
Requires (3AA) Batteries
5
When using an AC
Adapter, NEVER
place the adapter
plug into the Triangle power base
top peg holes.
Never connect more than 200
Laser Pegs® when using a 5 volt
(2000mA) AC Adapter.
The AC adapter used with the power base are to be regularly examined for
damage to the cord, plug, enclosure and other parts, and in the event of such
damage, they must not be used until the damage has been repaired.
WARNING! Each Laser Peg® draws current from the batteries. Therefore, the more
pegs you use, the quicker you will deplete your battery power! As the power
weakens, the current will slowly fail and some Laser Pegs® will illuminate (typically
the reds and yellows) and some won’t. When the Laser Pegs® dim the Laser Pegs®
are not broken, they just need stronger batteries or an AC Adapter.
You have 3 simple options...
1. Use a 5 volt AC Adapter –available from www.LaserPegs.com
2. Change the batteries.
3. Use high quality batteries. They will last a little longer, but they will still deplete rapidly the more laser pegs you connect!
STEP
2
STEP
6
STEP
12
COMBINE
B
STEP
16
STEP
STEP
STEP
20
STEP
7
STEP
STEP
8
13
21
17
D
STEP
9
C
STEP
14
STEP
21
B
STEP
STEP
18
10
STEP
15
STEP
STEP
22
23
STEP
STEP
11
19
www.LaserPegs.com
Copyright 2012© All Rights Reserved Global & Multiple Patents Pending.
US Patent #7,731,558
STEP
COMBINE
G
24
E
G
STEP
34
COMBINE
STEP
C
25
D
STEP
STEP
29
32
STEP
COMBINE
35
E
STEP
26
H
STEP
30
COMBINE
STEP
STEP
36
27
H
STEP
33
STEP
31
STEP
28
www.LaserPegs.com
Copyright 2012© All Rights Reserved Global & Multiple Patents Pending.
US Patent #7,731,558
Download PDF