Dell | 4320 | User`s guide | DELL 4320

Dell™ 4220/4320 Projector
User’s Guide
Notes, Cautions, and Warnings
NOTE: A NOTE indicates important information that helps you
make better use of your computer.
CAUTION: A CAUTION indicates potential damage to hardware
or loss of data if instructions are not followed.
WARNING: A WARNING indicates a potential for property
damage, personal injury, or death.
____________________
Information in this document is subject to change without notice.
© 2011 Dell Inc. All rights reserved.
Reproduction of these materials in any manner whatsoever without the written
permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell and the DELL logo are trademarks of
Dell Inc.; DLP and DLP logo are trademarks of TEXAS INSTRUMENTS
INCORPORATED; Microsoft and Windows are either trademarks or registered
trademarks of Microsoft Corporation in the United States and/or other countries.
Other trademarks and trade names may be used in this document to refer to either
the entities claiming the marks and names or their products. Dell Inc. disclaims
any proprietary interest in trademarks and trade names other than its own.
Model 4220/4320
March 2011
Rev. A00
Contents
1
Your Dell Projector .
About Your Projector
2
. . . . . . . . . . . . . . . . .
Connecting Your Projector .
. . . . . . . . . . .
Installing the Optional Wireless Dongle
Connecting to a Computer
8
10
. . . . . .
11
. . . . . . . . . . . . . . . .
12
. . . .
12
. . . . . . . . .
13
Connecting a Computer Using a VGA Cable
Monitor Loop-Through Connection
Using VGA Cables . . . . . . . . .
Connecting a Computer Using a RS232 Cable
Connecting a Computer by USB Cable
. . .
14
. . . . . . .
15
Connecting a Computer Using Wireless
Connecting a DVD Player
7
. . . . . . . . . . . . . . . . .
. . . . . .
16
. . . . . . . . . . . . . . . .
17
.
17
Connecting a DVD Player Using a
Composite Video Cable . . . . . .
. . . . . . . . .
18
Connecting a DVD Player Using a
Component Video Cable . . . . .
. . . . . . . . .
19
Connecting a DVD Player Using an S-Video Cable
Connecting a DVD Player Using an HDMI Cable
Connecting to Local Area Network
. .
20
. . . . . . . . . . .
21
To project an image and control the projector that is
connected to a network through a RJ45 cable. . . 21
Professional Installation Options: Installation for
Driving Automatic Screen . . . . . . . . . . . .
.
22
Connection With Commercial RS232 Control Box
.
23
Contents
3
3
Using Your Projector
. . . . . . . . . . . . . . . .
24
Turning Your Projector On
. . . . . . . . . . . . . . . .
24
Turning Your Projector Off .
. . . . . . . . . . . . . . .
Adjusting the Projected Image
. . . . . . . . . . . . .
Raising the Projector Height
. . . . . . . . . . . .
Lowering the Projector Height
. . . . . . . . . . .
Adjusting the Projector Zoom and Focus
25
. . . . . . . . . . . .
27
. . . . . . . . . . . . . . . . .
31
. . . . . . . . . . . . . . . .
33
. . . . . . . .
36
. . . . . . . . .
37
. . . . . . . . . . . . . .
38
INPUT SOURCE
. . . . . . . . . . . . . . . . . . .
38
AUTO ADJUST
. . . . . . . . . . . . . . . . . . .
39
Installing the Remote Control Batteries
Operating Range With Remote Control
Using the On-Screen Display
BRIGHTNESS/CONTRAST
. . . . . . . . . . . . .
40
. . . . . . . . . . . . . . . . . . . .
40
. . . . . . . . . . . . . . . . . . . . . .
41
VIDEO MODE
VOLUME
AUDIO INPUT .
. . . . . . . . . . . . . . . . . . .
ADVANCED SETTINGS
HELP
41
. . . . . . . . . . . . . . .
41
. . . . . . . . . . . . . . . . . . . . .
56
. . . . . . . . . . . . . . . . . . . . . . . .
56
LANGUAGE
Wireless Networking Installation
. . . . . . . . . . .
Enable Wireless on the Projector
. . . . . . . . .
Install the Wireless Application software on
Your Computer . . . . . . . . . . . . . . . .
Contents
25
26
Using the Remote Control
4
25
. . . . . . . .
Adjusting Projection Image Size
Using the Control Panel
24
. . .
57
58
60
Launch the Wireless Application
. . . . . . . . . .
63
. . . . . . . . . .
67
. . . . . . . . . . . . . . . . . . . . .
68
Presentation to Go (PtG) Installation
PtG Viewer
Photo Viewer
. . . . . . . . . . . . . . . . . . . .
PtG Overview
69
. . . . . . . . . . . . . . . . . . . .
69
Photo Overview
. . . . . . . . . . . . . . . . . . .
Buttons-Introduction
. . . . . . . . . . . . . . . .
Set up PtG Converter - Lite
. . . . . . . . . . . . .
PtG Converter - Lite Application Software
Audio Projection Installation
70
71
72
. . . . . . . . . . . . . .
73
. . . . .
Install the Dell Wireless Application Software
on Your Computer . . . . . . . . . . . . . . .
74
. . .
75
. . . . . . . . . .
77
. . . . . . . . . . . . . . . . . . . . . . . .
77
Launch the Wireless Application
Video Stream Installation
. . . . . . . . . . . . . . . .
Video Stream Support Format
. . . . . . . . . . .
Enable Wireless or LAN on the Projector
. . . . .
Install the Dell Wireless Application Software
on Your Computer . . . . . . . . . . . . . . .
79
79
80
. . .
80
. . . . . . . . . .
80
. . . . . . . . . . . . . . . . . . . . . . . .
80
Launch the Wireless Application
Login
70
. . . . .
Enable Wireless or LAN on the Projector
Login
68
. . . . . . . . . .
PtG/Photo Function Introduction
. . . .
81
. . . . . . . . . .
81
. . . . . . . . . . .
81
Managing the Projector From Web Management
Configuring the Network Setting
Accessing Web Management
Make Application Token .
. . . . . . . . . . . . . . .
Contents
100
5
4
Troubleshooting Your Projector
Guiding Signals
. . . . . . . . . . . . . . . . . . . . .
Changing the Lamp
6
. . . . . . . . . . . . . . . . . . .
5
Specifications
6
Contacting Dell
7
Appendix: Glossary
Contents
. . . . . .
101
105
106
. . . . . . . . . . . . . . . . . . . .
108
. . . . . . . . . . . . . . . . . . .
115
. . . . . . . . . . . . . . .
116
1
Your Dell Projector
Your projector comes with all the items shown below. Ensure that you have all the
items, and contact Dell™ if anything is missing.
Package Contents
Power cable
1.8 m VGA cable (VGA to VGA)
Carrying case
Remote control
CD User’s Guide and Documentation AAA Batteries (2)
USB cable
Your Dell Projector
7
About Your Projector
Top View
Bottom View
6
1
2
3
5
7
4
1
Control panel
2
Zoom tab
3
Focus ring
4
Lens
5
Elevator button for height adjustments
6
IR receivers
7
Lens cap
8
Mounting holes for wall mount: Screw hole M3 x 6.5 mm depth.
Recommended torque <8 kgf-cm
9
Mounting hole for tripod: Insert nut 1/4"*20 UNC
10
Lamp cover
11
Tilt adjustment wheel
12
Elevator foot
CAUTION: Safety Instructions
1 Do not use the projector near appliances that generate a lot of heat.
2 Do not use the projector in areas where there is an excessive amount of dust. The
dust may cause the system to fail and the projector will automatically shut down.
3 Ensure that the projector is mounted in a well-ventilated area.
4 Do not block the ventilation slots and openings on the projector.
8
Your Dell Projector
5 Ensure the projector operates between ambient temperatures (5 ºC to 35 ºC).
6 Do not try to touch the ventilation outlet as it can become very hot after the
projector has been turned on or immediately after it is turned off.
7 Do not look into the lens while the projector is on as it may cause injury to your
eyes.
8 Do not place any objects near or in front of the projector or cover its lens while the
projector is on as the heat may cause the object to melt or burn.
9 Do not use the wireless projector near cardiac pacemakers.
10 Do not use the wireless projector near medical equipment.
11 Do not use the wireless projector near microwave ovens.
NOTE:
• Do not attempt to wall mount the projector yourself. It should be installed
by a qualified technician.
• Recommended Projector Ceiling Mount Kit (P/N: C3505). For more
information, see the Dell Support website at support.dell.com.
• For more information, see the Safety Information that shipped with your
projector.
• The 4220/4320 projector can only be used indoors.
Your Dell Projector
9
2
Connecting Your Projector
1
2
3
4
5
6
7
8 9 10
20 19 18 17 16 15 14 13
11
12
1
Composite Video connector
11
WiFi USB (Type A) connector
2
S-Video connector
12
Security cable slot
3
VGA-A output (monitor loopthrough)
13
Audio output connector
4
VGA-A input (D-sub) connector
14
Audio-B input connector
5
VGA-B input (D-sub) connector
15
Audio-A input connector
6
HDMI connector
16
Audio-C right channel input
connector
7
Mini USB (Mini Type B)
connector for remote control
17
Power cord connector
8
RJ45 connector
18
Audio-C left-channel input
connector
9
USB Type A connector for USB
Viewer
19
RS232 connector
10
USB Type B connector for USB
Display
20
+12 V DC out connector
10
Connecting Your Projector
NOTE: Connectors are the same for 4220 and 4320 projectors.
CAUTION: Before you begin any of the procedures in this section, follow the
Safety Instructions as described on page 8.
Installing the Optional Wireless Dongle
Your projector must be installed with a wireless dongle if you want to use the
wireless networking option. Refer to "Wireless Networking Installation" on
page 57. The wireless dongle is not shipped with your 4220/4320 projector.
You can purchase it on the Dell website at www.dell.com.
1
Unscrew and take off the wireless cover.
2
Plug in the wireless dongle.
3
Assemble the wireless cover.
Connecting Your Projector
11
Connecting to a Computer
Connecting a Computer Using a VGA Cable
1
Power cord
2
VGA to VGA cable
3
USB-A to Mini USB-B cable
NOTE: The Mini USB cable is not shipped with your projector.
NOTE: The Mini USB cable must be connected if you want to use the Page Up
and Page Down features on the remote control.
12
Connecting Your Projector
Monitor Loop-Through Connection Using VGA Cables
1
Power cord
2
VGA to VGA cable
NOTE: Only one VGA cable is shipped with your projector. An additional VGA
cable can be purchased on the Dell website at www.dell.com.
Connecting Your Projector
13
Connecting a Computer Using a RS232 Cable
1
Power cord
2
RS232 cable
NOTE: The RS232 cable is not shipped with your projector. Consult a
professional installer for the cable and RS232 remote control software.
14
Connecting Your Projector
Connecting a Computer by USB Cable
1
Power cord
2
USB-A to USB-B cable
NOTE: Plug and Play. Only one USB cable is shipped with your projector. An
additional USB cable can be purchased on the Dell website at www.dell.com.
Connecting Your Projector
15
Connecting a Computer Using Wireless
NOTE: Your computer should be equipped with a wireless connector and
properly configured to detect another wireless connection. Refer to your
computer’s documentation on how to configure a wireless connection.
NOTE: Your projector must be installed with a wireless dongle if you want to
use the wireless networking. Refer to "Wireless Networking Installation" on
page 57.
16
Connecting Your Projector
Connecting a DVD Player
Connecting a DVD Player Using an S-Video Cable
1
Power cord
2
S-Video cable
NOTE: The S-Video cable is not shipped with your projector. You can purchase
the S-Video extension (50 ft/100 ft) cable on the Dell website at www.dell.com.
Connecting Your Projector
17
Connecting a DVD Player Using a Composite Video Cable
1
Power cord
2
Composite Video cable
NOTE: The Composite Video cable is not shipped with your projector. You can
purchase the Composite Video Extension (50 ft/100 ft) cable on the Dell website
at www.dell.com.
18
Connecting Your Projector
Connecting a DVD Player Using a Component Video Cable
1
Power cord
2
VGA to Component Video cable
NOTE: The VGA to Component Video cable is not shipped with your projector.
You can purchase the VGA to Component Video Extension (50 ft/100 ft) cable on
the Dell website at www.dell.com.
Connecting Your Projector
19
Connecting a DVD Player Using an HDMI Cable
1
Power cord
2
HDMI cable
NOTE: The HDMI cable is not shipped with your projector. You can purchase
the HDMI cable on the Dell website at www.dell.com.
20
Connecting Your Projector
Connecting to Local Area Network
To project an image and control the projector that is connected to a
network through a RJ45 cable.
Local Area Network (LAN)
1
Power cord
2
RJ45 cable
NOTE: The RJ45 cable is not shipped with your projector. You can purchase the
RJ45 cable on the Dell website at www.dell.com.
Connecting Your Projector
21
Professional Installation Options: Installation for Driving Automatic
Screen
1
Power cord
2
12 V DC Plug
3
Motorized projection screen
NOTE: Use a 12 V DC plug in, 1.7 mm (ID) x 4.00 mm (OD) x 9.5 mm (shaft), to
connect the automatic screen to the projector.
12 V DC Plug
22
Connecting Your Projector
Connection With Commercial RS232 Control Box
1
Power cord
2
RS232 cable
3
Commercial RS232 control box
NOTE: The RS232 cable is not shipped with your projector. Consult a
professional technician to obtain the cable.
Connecting Your Projector
23
Using Your Projector
3
Turning Your Projector On
NOTE: Turn on the projector before you turn on the source (computer, DVD
player, etc.). The Power button light blinks blue until pressed.
1 Remove the lens cap.
2 Connect the power cord and appropriate signal cables to the projector. For
information about connecting the projector, see "Connecting Your Projector" on
page 10.
3 Press the Power button (see "Using the Control Panel" on page 31 to locate the
Power button).
4 Turn on your source (computer, DVD player, etc.)
5 Connect your source to the projector using the appropriate cable. See
"Connecting Your Projector" on page 10 for instructions to connect your source to
the projector.
6 By default, the input source of the projector is set to VGA-A. Change the input
source of the projector if necessary.
7 If you have multiple sources connected to the projector, press the Source button
on the remote control or control panel to select the desired source. See "Using the
Control Panel" on page 31 and "Using the Remote Control" on page 33 to locate
the Source button.
Turning Your Projector Off
CAUTION: Unplug the projector after properly shutting down as explained in
the following procedure.
1 Press the Power button. Follow the instruction displayed on screen to properly
turn off the projector.
NOTE: The "Press Power Button to Turn off Projector" message will
appear on the screen. The message disappears after 5 seconds or you can
press the Menu button to clear it.
2 Press the Power button again. The cooling fans continue to operate for 120
seconds.
24
Using Your Projector
3 To power off the projector quickly, press the Power button and hold for 1 second
while the projector’s cooling fans are still running.
NOTE: Before you turn on the projector again, wait for 60 seconds to allow the
internal temperature to stabilize.
4 Disconnect the power cord from the electrical outlet and the projector.
Adjusting the Projected Image
Raising the Projector Height
1 Press the Elevator button.
2 Raise the projector to the desired display angle, and then release the button to
lock the elevator foot into position.
3 Use the tilt adjustment wheel to fine-tune the display angle.
Lowering the Projector Height
1 Press the Elevator button.
2 Lower the projector, then release the button to lock the elevator foot into
position.
1
Elevator button
2
Elevator foot (Angle of tilt: 0 to 9.5 degrees)
3
Tilt adjustment wheel
Using Your Projector
25
Adjusting the Projector Zoom and Focus
CAUTION: To avoid damaging the projector, ensure that the zoom lens and
elevator foot are fully retracted before moving the projector or placing the
projector in its carrying case.
1 Rotate the zoom tab to zoom in and out.
2 Rotate the focus tab until the image is clear. The projector focuses at distances
ranging between 3.94 ft to 32.81 ft (1.2 m to 10 m).
1
Zoom tab
2
Focus ring
26
Using Your Projector
Adjusting Projection Image Size
Projector to screen distance
4220
Using Your Projector
27
Projector to screen distance
4320
28
Using Your Projector
Height (Hd): 106.3 cm
n
sta
Di
.0
:5
ce
m
29
Using Your Projector
4220
Screen
(Diagonal)
Max.
37"
(93.98 cm)
92"
154"
215"
277"
307"
(233.68 cm) (391.16 cm) (546.10 cm) (703.58 cm) (779.78 cm)
Min.
30.8"
(78.23 cm)
128"
179"
231"
256"
77"
(195.58 cm) (325.12 cm) (454.66 cm) (586.74 cm) (650.24 cm)
Max.
29.53" X
(WxH) 22.05"
Screen
Size
Hd
74.02" X
55.51"
123.23" X
92.13"
172.44" X
129.13"
221.65" X
166.14"
246.06" X
184.65"
(188 cm X
141 cm)
(313 cm X
234 cm)
(438 cm X
328 cm)
(563 cm X
422 cm)
(625 cm X
469 cm)
61.42" X
46.06"
102.36" X
76.77"
143.70" X
107.48"
184.65" X
138.58"
205.12" X
153.94"
(63 cm X
47 cm)
(156 cm X
117 cm)
(260 cm X
195 cm)
(365 cm X
273 cm)
(469 cm X
352 cm)
(521 cm X
391 cm)
Max.
25.59"
(65 cm)
63.78"
(162 cm)
106.30"
(270 cm)
148.43"
(377 cm)
190.94"
(485 cm)
212.20"
(539 cm)
Min.
21.26"
(54 cm)
53.15"
(135 cm)
88.58"
(225 cm)
123.62"
(314 cm)
159.06"
(404 cm)
176.77"
(449 cm)
3.94'
(1.2 m)
9.84'
(3.0 m)
16.40'
(5.0 m)
22.97'
(7.0 m)
29.53'
(9.0 m)
32.81'
(10 m)
(75 cm X
56 cm)
24.80" X
Min.
(WxH) 18.50"
Distance
* This graph is for user reference only.
4320
Screen
(Diagonal)
Max.
44"
109"
181"
254"
326"
363"
(111.76 cm) (276.86 cm) (459.74 cm) (645.16 cm) (828.04 cm) (922.02 cm)
Min.
36.3"
(92.20 cm)
Max.
37.01" X
(WxH) 23.23"
Screen
Size
Hd
Distance
91"
151"
212"
272"
302"
(231.14 cm) (383.54 cm) (538.48 cm) (690.88 cm) (767.08 cm)
92.13" X
57.48"
153.94" X
96.06"
215.35" X
134.65"
276.77" X
172.83"
307.48" X
192.13"
(234 cm X
146 cm)
(391 cm X
244 cm)
(547 cm X
342 cm)
(703 cm X
439 cm)
(781 cm X
488 cm)
76.77" X
48.03"
128.35" X
79.92"
179.53" X
112.20"
230.71" X
144.09"
256.30" X
160.24"
(78 cm X
49 cm)
(195 cm X
122 cm)
(326 cm X
203 cm)
(456 cm X
285 cm)
(586 cm X
366 cm)
(651 cm X
407 cm)
Max.
25.98"
(66 cm)
64.96"
(165 cm)
107.87"
(274 cm)
151.18"
(384 cm)
194.49"
(494 cm)
216.14"
(549 cm)
Min.
21.65"
(55 cm)
53.94"
(137 cm)
90.16"
(229 cm)
125.98"
(320 cm)
162.20"
(412 cm)
179.92"
(457 cm)
3.94'
(1.2 m)
9.84'
(3.0 m)
16.40'
(5.0 m)
22.97'
(7.0 m)
29.53'
(9.0 m)
32.81'
(10 m)
(94 cm X
59 cm)
Min.
30.71" X
(WxH) 19.29"
* This graph is for user reference only.
30
Using Your Projector
Using the Control Panel
1
LAMP warning light
If the LAMP amber indicator is on or blinking,
one of the following problems could be occurring:
• Lamp is reaching its end of usable life
• Lamp module is not properly installed
• Lamp driver failure
• Color wheel failure
For more information, see "Troubleshooting Your
Projector" on page 101 and "Guiding Signals" on
page 105.
2
TEMP warning light
If the TEMP amber indicator is on or blinking,
one of the following problems could be occurring:
• Internal temperature of the projector is too
high
• Color wheel failure
For more information, see "Troubleshooting Your
Projector" on page 101 and "Guiding Signals" on
page 105.
3
Power
Turns the projector on or off. For more
information, see "Turning Your Projector On" on
page 24 and "Turning Your Projector Off" on
page 24.
Using Your Projector
31
4
Up
/ Keystone
adjustment
Press to navigate through the On-Screen Display
(OSD) Menu items.
Press to adjust image distortion caused by tilting
the projector (+40/-35 degrees).
5
Right
/ Auto Adjust
Press to navigate through the On-Screen Display
(OSD) Menu items.
Press to synchronize the projector to the input
source.
NOTE: Auto Adjust does not operate if the
on-screen display (OSD) is displayed.
6
IR Receiver
Point the remote control towards the IR receiver
and press a button.
7
Down
/ Keystone
adjustment
Press to navigate through the On-Screen Display
(OSD) Menu items.
Press to adjust image distortion caused by tilting
the projector (+40/-35 degrees).
8
Menu
9
Left
Press to activate the OSD. Use the directional
keys and the Menu button to navigate through
the OSD.
/ Source
Press to navigate through the On-Screen Display
(OSD) Menu items.
Press to toggle through Analog RGB, Composite,
Component (YPbPr via VGA), HDMI, and
S-Video sources when multiple sources are
connected to the projector.
10
32
Enter
Using Your Projector
Press to confirm the selection item.
Using the Remote Control
1
15
2
16
3
4
17
5
18
19
6
21
20
22
8
9
10
23
24
11
12
25
13
14
26
7
1
Power
Turns the projector on or off. For more
information, see "Turning Your Projector On" on
page 24 and "Turning Your Projector Off" on
page 24.
2
Enter
Press to confirm the selection.
3
Right
Press to navigate through the On-Screen Display
(OSD) Menu items.
4
Down
Press to navigate through the On-Screen Display
(OSD) Menu items.
Using Your Projector
33
5
Laser
Point the remote control at the screen, press and
hold the laser button to activate the laser light.
WARNING: Do not look at the laser point
when it is active. Avoid directing the laser
light on your eyes.
6
Aspect Ratio
Press to change the aspect ratio of a displayed
image.
7
Keystone adjustment
Press to adjust image distortion caused by tilting
the projector (+40/-35 degrees).
8
Page up
Press to move to the previous page.
NOTE: The Mini USB cable must be
connected if you want to use the Page Up
feature.
9
Page down
Press to move to the next page.
NOTE: The Mini USB cable must be
connected if you want to use the Page Down
feature.
10 Keystone adjustment
Press to adjust image distortion caused by tilting
the projector (+40/-35 degrees).
11 S-Video
Press to choose S-Video source.
12 Video
Press to choose Composite Video source.
13 Video mode
The projector has preset configurations that are
optimized for displaying data (presentation
slides) or video (movies, games, etc.).
Press the Video Mode button to toggle between
Presentation mode, Bright mode, Movie mode,
sRGB, or Custom mode.
Pressing the Video Mode button once will show
the current display mode. Pressing the Video
Mode button again will switch between modes.
14 Blank screen
Press to hide/unhide the image.
15 Up
Press to navigate through the On-Screen Display
(OSD) Menu items.
34
Using Your Projector
16 Left
Press to navigate through the On-Screen Display
(OSD) Menu items.
17 Menu
Press to activate the OSD.
18 Mute
Press to mute or un-mute the projector speaker.
19 Zoom +
Press to increase the image.
20 Zoom -
Press to decrease the image.
21
Press to increase the volume.
Volume up
22 Volume down
Press to decrease the volume.
23 Freeze
Press to pause the screen image, then press
"Freeze" again to unfreeze image.
24 VGA
Press to choose VGA source.
25 Source
Press to switch between Analog RGB, Composite,
Component (YPbPr, via VGA), HDMI, and
S-Video source.
26 Auto Adjust
Press to synchronize the projector with the input
source. Auto Adjust does not operate if the OSD
is displayed.
Using Your Projector
35
Installing the Remote Control Batteries
NOTE: Remove the batteries from the remote control when not in use.
1 Press the tab to lift the battery compartment cover.
1
2 Check the polarity (+/-) marking on the batteries.
2
3 Insert the batteries and align their polarity correctly
according to the marking in the battery compartment.
3
NOTE: Avoid mixing different types of batteries or using
new and old batteries together.
4 Slip the battery cover back.
36
Using Your Projector
4
Operating Range With Remote Control
Angle
Distance
Distance
Operating range
Angle
±20°
7 m/22.97 feet
Angle
e
nc
sta
Di
NOTE: Actual operating range may slightly differ from the diagram. Weak
batteries will also prevent the remote control from properly operating the
projector.
Using Your Projector
37
Using the On-Screen Display
• The projector has a multi-language On-Screen Display (OSD) Menu that can be
displayed with or without an input source.
• Press the Menu button on the control panel or the remote control to enter the
Main Menu.
• To navigate through the tabs in the Main Menu, press the
or
buttons on
your projector’s control panel or remote control.
• To select a submenu, press the
or
button on your projector’s control panel
or remote control.
• To select an option, press the
or
buttons on your projector’s control panel
or remote control. When an item is selected, the color changes to dark blue.
• Use the
or
buttons on the control panel or remote control to adjust the
settings.
• To go back to the Main Menu, press the
button on the control panel or the
remote control.
• To exit the OSD, press the Menu button directly on the control panel or the
remote control.
NOTE: OSD structure and set are the same for the 4220 and 4320 models.
INPUT SOURCE
The Input Source menu allows you to select your projector’s input source.
VGA-A—Press
to detect a VGA-A signal.
VGA-B—Press
to detect a VGA-B signal.
HDMI—Press
COMPOSITE—Press
S-VIDEO—Press
to detect a HDMI signal.
to detect a Composite Video signal.
to detect a S-Video signal.
WIRELESS/USB—Press
38
to activate the Input Source Wireless/USB menu.
Using Your Projector
NOTE: The Wireless/USB can be used after the "Wireless and LAN" option is
turned on.
INPUT SOURCE WIRELESS/USB
The Input Source Wireless/USB menu allows you to activate the Wireless Display,
USB Display, and USB Viewer.
to access the projector's Wireless Guide screen. See
WIRELESS DISPLAY—Press
"Wireless Guide screen" on page 59.
USB DISPLAY—Allows you to display the computer/laptop screen to your projector
via the USB cable.
USB VIEWER—Allows you to display photo and PPT files from your USB flash. See
"Presentation to Go (PtG) Installation" on page 67.
AUTO ADJUST
Auto Adjust automatically adjusts the projector's Horizontal, Vertical, Frequency,
and Tracking in PC mode.
Using Your Projector
39
BRIGHTNESS/CONTRAST
The Brightness/Contrast menu allows you adjust the brightness/contrast settings
of your projector.
BRIGHTNESS—Use
CONTRAST—Use
and
and
to adjust the brightness of the image.
to adjust the display contrast.
NOTE: If you adjust the settings for Brightness and Contrast the projector
automatically switch to Custom mode.
VIDEO MODE
The Video Mode menu allows you to optimize the display image: Presentation,
Bright, Movie, sRGB (provides more accurate color representation), and Custom
(set your preferred settings).
40
Using Your Projector
VOLUME
The Volume menu allows you adjust the volume settings of your projector.
VOLUME—Press
to increase the volume and
to decrease the volume.
AUDIO INPUT
The Audio Input menu allows you to select your audio input source. The options
are: Audio-A, Audio-B, Audio-C, HDMI, and Wireless/LAN.
ADVANCED SETTINGS
The Advanced Settings menu allows you to change settings for Image, Display,
Projector, LAN, Wireless, Menu, Power, and Information.
Using Your Projector
41
IMAGE SETTINGS (IN PC MODE)—Select and press
to activate image settings.
The image settings menu provides the following options:
COLOR TEMPERATURE—Allows you to adjust the color temperature. The
screen appears cooler at higher color temperatures and warmer at lower
color temperatures. When you adjust the values in the Color Adjust menu,
the Custom mode is activated. The values are saved in the Custom mode.
RGB COLOR ADJUST—Allows you to manually adjust the colors red, green,
and blue.
WHITE INTENSITY—Press
and use
and
to display white intensity.
COLOR SPACE—Allows you to select the color space. The options are: RGB,
YCbCr, and YPbPr.
VGA OUTPUT—Select On or Off the VGA output function at projector
standby status. Default is Off.
NOTE: If you adjust the settings for Color Temperature, RGB Color Adjust, and
White Intensity the projector automatically switch to Custom mode.
IMAGE SETTINGS (IN VIDEO MODE)—Select and press
to activate image settings.
The image settings menu provides the following options:
42
Using Your Projector
COLOR TEMPERATURE—Allows you to adjust the color temperature. The
screen appears cooler at higher color temperatures and warmer at lower
color temperatures. When you adjust the values in the Color Adjust menu,
the Custom mode is activated. The values are saved in the Custom mode.
RGB COLOR ADJUST—Allows you to manually adjust the colors red, green,
and blue.
SATURATION—Allows you to adjust the video source from black and white
to fully saturated color. Press
to increase the amount of color in the
image and
to decrease the amount of color in the image.
SHARPNESS—Press
sharpness.
to increase the sharpness and
to decrease the
TINT—Press
to increase the amount of green in the image and
to
decrease the amount of green in the image (available for NTSC only).
WHITE INTENSITY—Press
and use
and
to display white intensity.
COLOR SPACE—Allows you to select the color space. The options are: RGB,
YCbCr, and YPbPr.
VGA OUTPUT—Select On or Off the VGA output function at projector
standby status. Default is Off.
NOTE:
1 If you adjust the settings for Color Temperature, RGB Color Adjust,
Saturation, Sharpness, Tint, and White Intensity the projector
automatically switch to Custom mode.
2 Saturation, Sharpness, and Tint are only available when the input source is
from Composite or S-Video.
IMAGE SETTINGS (NO INPUT SOURCE)—Select and press
to activate image
settings. The image settings menu provides the following options:
VGA OUTPUT—Select On or Off the VGA output function at projector
standby status. Default is Off.
Using Your Projector
43
DISPLAY SETTINGS (IN PC MODE)—Select and press
to activate display settings.
The display settings menu provides the following options:
HORIZONTAL POSITION—Press
the image left.
VERTICAL POSITION—Press
image down.
to move the image right and
to move the image up and
to move
to move the
FREQUENCY—Allows you to change the display data clock frequency to
match the frequency of your computer’s graphics card. If you see a vertical
flickering wave, use the Frequency control to minimize the bars. This is a
coarse adjustment.
TRACKING—Synchronize the phase of the display signal with the graphic
card. If you experience an unstable or flickering image, use Tracking to
correct it. This is a fine adjustment.
ASPECT RATIO—Allows you to select the aspect ratio to adjust how the
image appears. Options are: Origin, 16:9, and 4:3.
•Origin — Select Origin to maintain the aspect ratio of the image
projector according to the input source.
•16:9 — The input source scales to fit the width of the screen to project a
16:9 screen image.
•4:3 — The input source scales to fit the screen and projects a 4:3 image.
ZOOM—Press
and
to zoom and view the image.
Adjust the image scale by pressing
or
and press
to view on your remote control
only.
ZOOM NAVIGATION—Press
Navigation menu.
Use
44
Using Your Projector
to activate the Zoom
to navigate the projection screen.
3D DISPLAY—Select On to start the 3D display function (default is Off).
NOTE:
1. When you want to create a 3D experience, you will need a few other
components including:
a
Computer/Laptop with a 120 Hz signal output quad-buffered
graphics card.
b
"Active" 3D glasses with DLP Link™.
c
3D content. See "Note 4".
d
3D Player. (Example: Stereoscopic Player...)
2. Enable the 3D function when it satisfies any of the below-mentioned
conditions:
a
Computer/Laptop with a graphics card, capable of outputting a
120 Hz signal via VGA or HDMI cable.
b
Input a suite of 3D content via Video and S-Video.
3. "3D Display" selection will only be enabled in the "Display Settings of
the Advanced Settings" menu when the projector detects either of
the inputs mentioned above.
4. 3D support and refresh rate are as below:
a
VGA/HDMI 1280 x 720 120 Hz, 1024 x 768 120 Hz, and 800 x 600 120 Hz
b
Composite/S-Video 60 Hz
c
Component 480i
5. The recommended VGA signal for laptop is Single-mode output
(Dual mode is not recommended).
3D SYNC INVERT—If you see a discrete or overlapping image while wearing
DLP 3D goggles, you may need to execute 'Invert' to get best match of
left/right image sequence to get the correct image. (For DLP 3D goggles)
Using Your Projector
45
DISPLAY SETTINGS (IN VIDEO MODE)—Select and press
to activate display
settings. The display settings menu provides the following options:
ASPECT RATIO—Allows you to select the aspect ratio to adjust how the
image appears. Options are: Origin, 16:9, and 4:3.
•Origin — Select Origin to maintain the aspect ratio of image projector
according to the input source.
•16:9 — The input source scales to fit the width of the screen to project a
16:9 screen image.
•4:3 — The input source scales to fit the screen and projects a 4:3 image.
ZOOM—Press
and
to zoom and view the image.
Adjust the image scale by pressing
or
and press
to view on your remote control
only.
ZOOM NAVIGATION—Press
Navigation menu.
Use
to activate the Zoom
to navigate the projection screen.
3D DISPLAY—Select On to start the 3D display function (default is Off).
NOTE:
1. When you want to create a 3D experience, you will need a few other
components including:
46
a
Computer/Laptop with a 120 Hz signal output quad-buffered
graphics card.
b
"Active" 3D glasses with DLP Link™.
c
3D content. See "Note 4".
d
3D Player. (Example: Stereoscopic Player...)
Using Your Projector
2. Enable the 3D function when it satisfies any of the below-mentioned
conditions:
a
Computer/Laptop with a graphics card, capable of outputting a
120 Hz signal via VGA or HDMI cable.
b
Input a suite of 3D content via Video and S-Video.
3. "3D Display" selection will only be enabled in the "Display Settings of
the Advanced Settings" menu when the projector detects either of
the inputs mentioned above.
4. 3D support and refresh rate are as below:
a
VGA/HDMI 1280 x 720 120 Hz, 1024 x 768 120 Hz, and 800 x 600 120 Hz
b
Composite/S-Video 60 Hz
c
Component 480i
5. The recommended VGA signal for laptop is Single-mode output
(Dual mode is not recommended).
3D SYNC INVERT—If you see a discrete or overlapping image while wearing
DLP 3D goggles, you may need to execute 'Invert' to get best match of
left/right image sequence to get the correct image. (For DLP 3D goggles)
Using Your Projector
47
PROJECTOR SETTINGS—Select and press
to activate projector settings. The
projector settings menu provides the following options:
AUTO SOURCE—Select Off (the default) to lock the current input signal. If
you press the Source button when the Auto Source mode is set to Off, you
can manually select the input signal. Select On to auto detect the available
input signals. If you press the Source button when the projector is on, it
automatically finds the next available input signal.
AUTO KEYSTONE—Select On to automatically adjust image distortion
caused by tilting the projector.
PROJECTOR MODE—Allows you to select the projector mode, depending
upon how the projector is mounted.
•Rear Projection-Desktop — The projector reverses the image so that you
can project from behind a translucent screen.
•Rear Projection-Ceiling Mount — The projector reverses and turns the
image upside down. You can project from behind a translucent screen with
a ceiling-mounted projection.
•Front Projection-Desktop — This is the default option.
•Front Projection-Ceiling Mount — The projector turns the image upside
down for ceiling-mounted projection.
SPEAKER—Select On to enable the speaker. Select Off to the disable
speaker.
CLOSED CAPTION—Select On to enable close caption and activate the
closed caption menu. Select appropriate closed caption options: CC1,
CC2, CC3, and CC4.
NOTE: Closed caption option is available for NTSC only.
48
Using Your Projector
STARTUP SCREEN—Default is Dell logo as wallpaper. You can also select
Capture Screen option to capture the screen display. The following
message appears on the screen.
NOTE: To capture a full image, ensure that the input signal connected
to the projector is at 1024 x 768 resolution.
TEST PATTERN—Test Pattern is used to test focus and resolution.
You can enable or disable the Test Pattern by selecting Off, 1, or 2. You can
also invoke the Test Pattern 1 by pressing and holding down
and
buttons on the control panel simultaneously for 2 seconds. You can also
invoke the test pattern 2 by pressing and holding down
and
buttons
on the control panel simultaneously for 2 seconds.
Test Pattern 1:
Test Pattern 2:
FACTORY RESET—Select and press
to reset all settings to its factory
default. The below warning message appears:
Using Your Projector
49
Reset items include both computer sources and Video source settings.
LAN SETTINGS—Select and press
menu provides the following options:
to activate LAN settings. The LAN settings
WIRELESS AND LAN—Select Enabled to active the Wireless and LAN
function.
DHCP—If a DHCP server exists in the network to which the projector is
connected, the IP address will automatically be acquired when you select
DHCP On. If DHCP is Off, manually set the IP Address, Subnet Mask,
and Gateway. Use
and
to select the number of IP address, Subnet
Mask, and Gateway. Key in enter to confirm each number and then use
and
to set the next item.
IP ADDRESS—Automatically or manually assigns the IP address to the
projector connected to the network.
SUBNET MASK—Configure the Subnet Mask of the network connection.
GATEWAY—Check the Gateway address with your network/system
administrator if you configure it manually.
DNS—Check the DNS Server IP address with your network/system
administrator if you configure it manually.
STORE—Press
settings.
to save the changes made in network configuration
NOTE:
1. Use
and
buttons to select IP Address, Subnet Mask,
Gateway, DNS, and Store.
2. Press the
button to enter IP Address, Subnet Mask, Gateway, or
DNS to set the value. (The selected option is highlighted in blue)
50
a
Use
and
b
Use
and
Using Your Projector
buttons to select the option.
buttons to set the value.
c
After the setup is complete, press the
button to exit.
3. After the IP Address, Subnet Mask, Gateway, and DNS is set up,
select Store and press
button to store the settings.
4. If you select Store without pressing the Enter button, the system will
keep the original settings.
RESET—Press
to reset network configuration.
WIRELESS SETTINGS—Select and press
to activate wireless settings. The
wireless settings menu provides the following options:
WIRELESS—Default option is Connected. Select Disconnected to disable
the wireless connection.
NOTE: It is recommended to use the default settings for Wireless
Connect.
DHCP SERVER—Allows you to enable DHCP server of the wireless.
START IP ADDRESS—Automatically or manually assigns the Start IP
address of the DHCP server to the projector connected to the wireless.
END IP ADDRESS—Automatically or manually assigns the End IP address of
the DHCP server to the projector connected to the wireless.
SUBNET MASK—Configure the Subnet Mask of the wireless connection.
GATEWAY—Check the Gateway address with your network/system
administrator if you configure it manually.
DNS—Check the DNS Server IP address with your network/system
administrator if you configure it manually.
STORE—Press
settings.
to save the changes made in wireless configuration
NOTE:
1. Use
and
buttons to select IP Address, Subnet Mask,
Gateway, DNS, and Store.
Using Your Projector
51
2. Press the
button to enter IP Address, Subnet Mask, Gateway, or
DNS to set the value. (The selected option is highlighted in blue)
a
Use
and
buttons to select the option.
b
Use
and
c
After the setup is complete, press the
buttons to set the value.
button to exit.
3. After the IP Address, Subnet Mask, Gateway, and DNS is set up,
select Store and press
button to store the settings.
4. If you select Store without pressing the Enter button, the system will
keep the original settings.
RESET—Press
to reset wireless configuration.
MENU SETTINGS—Select and press
to activate the menu settings. The menu
settings consists of the following options:
MENU POSITION—Allows you to change the position of the OSD menu on
the screen.
MENU TIMEOUT—Allows you to adjust the time for an OSD timeout. By
default, the OSD disappears after 20 seconds of non-activity.
MENU TRANSPARENCY—Select to change the transparency level of the OSD
background.
MENU LOCK—Select On to enable the Menu Lock and hide the OSD
menu. Select Off to disable the Menu Lock. If you want to disable the
Menu Lock function and have the OSD disappear, press the Menu button
on the control panel or remote control for 15 seconds, and then disable the
function.
PASSWORD—When Password Protect is enabled, a Password Protect screen
requesting you to enter a password will be displayed when the power plug is
inserted into the electrical output and the power for the projector is first
turned on. By default, this function is disabled. You can enable this feature
by selecting Enabled. If the password has been set before, key in the
52
Using Your Projector
password first and select the function. This password security feature will
be activated the next time you turn on the projector. If you enable this
feature, you will be asked to enter the projector’s password after you turn
on the projector:
1 First time password input request:
a Go to Menu Settings, press
the password settings.
and then select Password to Enabled
b Enabling the Password function will pop up a change screen. Key in a
4-digit number from the screen and press
.
4320
Password screen
4220 Password screen
c To confirm, enter the password again.
d If the password verification is successful, you may resume with accessing
the projector's functions and its utilities.
2 If you have entered an incorrect password, you will be given another two
chances. After three invalid attempts, the projector will automatically turn
off.
NOTE: If you forget your password, contact DELL™ or a qualified
service personnel.
3 To disable the password function, select the Disabled option to close the
function.
4 To delete the password, select the Delete option.
Using Your Projector
53
CHANGE PASSWORD—Key in the original password. Then, enter the new
password and confirm the new password again.
4320 Change Password screen
4220 Change Password screen
POWER SETTINGS—Select and press
to activate power settings. The power
settings menu provides the following options:
54
Using Your Projector
QUICK SHUTDOWN—Select On to turn off the projector with a single press of
the Power button. This function allows the projector to quickly power off
with an accelerated fan speed. Slightly higher acoustic noise is expected
during quick power off.
NOTE: Before you turn on the projector again, wait for 60 seconds to
allow the internal temperature to stabilize. The projector will take a
longer time to turn on if you try to power on immediately. Its cooling fan
will run at full speed for about 30 seconds to stabilize the internal
temperature.
POWER SAVING—Select Off to disable Power Saving mode. By default, the
projector is set to enter power saving mode after 120 minutes of no activity.
A warning message appears on screen showing a 60 seconds countdown
before switching to power saving mode. Press any button during the
countdown period to stop the power-saving mode.
You can also set a different delay period to enter power saving mode. The
delay period is the time you want the projector to wait without an input
signal. Power saving can be set to 30, 60, 90, or 120 minutes.
If an input signal is not detected during the delay period, the projector
turns off. To turn on the projector press the Power button.
DURING STANDBY—Select Wireless On or Off to set the Wireless/LAN
module on/off while the projector is standby status (default is Wireless
Off).
LAMP MODE—Allows you to select between Normal or ECO mode.
Normal mode operates at full power level. ECO mode operates at a lower
power level which may provide longer lamp life, quieter operation, and
dimmer luminance output on the screen.
LAMP HOUR RESET—Press
lamp hour.
and select the Confirm option to reset the
Using Your Projector
55
INFORMATION—The information menu displays the current 4220 or 4320
projector settings.
LANGUAGE
Allows you to set the language for the OSD. Press
menu.
to activate the Language
HELP
If you encounter problems with your projector, you can access the help menu for
troubleshooting.
56
Using Your Projector
Wireless Networking Installation
NOTE: Your computer must have the following minimum system requirements:
Operating System:
• Windows
Microsoft Windows 2000™ with service pack 4 or later, Windows XP™ Home or
Professional Service pack 2 (32-bit recommended), Windows Vista 32-bit, and
Windows® 7 Home or Professional 32-bit or 64-bit
• MAC
MacBook and above, MacOS 10.5 and above
Minimum Hardware:
a Intel Dual Core 1.4 MHz or higher
b 256 MB of RAM required, 512 MB or more recommended
c 10 MB of available hard-disk space
d nViDIA or ATI graphic card must with 64 MB VRAM or above
e Ethernet adapter (10 / 100 bps) for an Ethernet connection
f A supported WLAN adapter for a WLAN connection (any NDIS-compliant
802.11b or 802.11g or 802.11n WiFi device)
Web browser
Microsoft Internet Explorer 6.0 or 7.0 (recommended) or 8.0, Firefox 1.5 or 2.0,
and Safari 3.0 and above
NOTE: Wireless Networking Installation steps are the same for the 4220 and
4320 models.
Using Your Projector
57
Enable Wireless on the Projector
In order to use your projector wirelessly, you need to complete the steps below:
1
Install the optional wireless dongle. See "Installing the Optional Wireless
Dongle" on page 11.
2
Connect the power cable to the wall outlet and press the power button.
3
Press the Menu button on your projector control panel or remote control.
4
The wireless connection default is enable. See "Wireless Settings" on page 51.
5
Access the INPUT SOURCE menu, select Wireless/USB and then select
Wireless Display on the sub-menu. See "INPUT SOURCE WIRELESS/USB"
on page 39.
NOTE: Use
58
,
,
and
Using Your Projector
buttons to navigate and
to select.
The Wireless Guide Screen shown below appears:
NOTE: If wireless connection is disabled, then follow these steps to set up:
ADVANCED SETTINGS J Wireless settings J Wireless J Connected. The
image input source will be automatically switched to wireless screen when
wireless option is selected in this step.
6
Take note of the LOGIN CODE, NETWORK NAME (SSID), and IP
ADDRESS. You will need these information to log in later.
Using Your Projector
59
Install the Wireless Application software on Your Computer
7
Connect your computer to the 4220 or 4320 wireless network.
NOTE:
• Your computer must have wireless network function to detect the
connection.
• When you connect to the 4220 or 4320 wireless network, you will lose
wireless connectivity with other wireless networks.
NOTE: Remember to turn off all proxies. (In Microsoft® Windows Vista: Click
Control Panel J Internet Options J Connections J LAN Settings)
8
60
Open your Internet browser. You will be automatically directed to the 4220 or
4320 Web Management web page.
Using Your Projector
NOTE: If the web page does not load automatically, enter the IP address
(default IP address is 192.168.100.10) noted from the projector’s screen in the
browser’s address bar.
9
10
The 4220 or 4320 Web Management page opens. For first time use, click
Download.
Select the appropriate operating system, then click Download.
Using Your Projector
61
11
Click Run to proceed with the
one-time installation of the
software.
NOTE: You may choose to
save the file and install it at a
latter time. To do this, click
Save.
NOTE: If you are unable to
install the application because of inadequate rights on the computer, please
contact your network administrator.
12
62
The installation software will launch. Follow the on-screen instructions to
complete setup.
Using Your Projector
Launch the Wireless Application
Once the installation is complete, the 4220 or 4320 Wireless Application software
will launch and will search for the projector automatically. The below screen
appears:
Login
To communicate with your projector, enter the Login Code provided in Step 6 of
Wireless Networking Installation, then click OK.
4220 Log in screen
4320 Log in screen
NOTE: If the IP Address is not detected, enter the IP Address displayed at the
bottom left corner of the screen.
Understanding the Buttons
After a successful log in, the following screen appears:
Using Your Projector
63
Projection Mode
1
2
3
4
1
2
3
4
Item
Description
Status Bar
Displays IP and LOGIN CODE information.
Menu
Click to activate the application menu.
Minimize button
Click to minimize the application.
Close button
Click to exit the application.
Status Mode
Projection Mode
Click to activate the projection mode.
Video Mode
Click to activate the video mode.
Controls Toolbar
Full screen
Click to project the image in full screen.
Split 1
Click to project the image in the upper left
corner of the screen.
Split 2
Click to project the image in the upper right
corner of the screen.
Split 3
Click to project the image in the lower left
corner of the screen.
Split 4
Click to project the image in the lower right
corner of the screen.
Stop
Click to stop projection.
Pause
Click to pause projection.
Audio Projection
Click to enable audio projection.
Connection Status
Connection Icon
Blinks when projection is in progress.
Projecting the Presentation
• To project the presentation, click any of the projection buttons
• To pause the presentation, click
. The icon turns green.
• To continue the presentation, click
again.
64
Using Your Projector
.
• To audio projection the presentation, click
Installation" on page 73.
• To stop the presentation, click
.
. See "Audio Projection
Video Mode
1
Item
1
Description
Control Toolbar
Open
Click to open folder and searching the video
or music file.
Play
Click to starting player.
Stop
Click to stop player.
Mute
Click to mute/un-mute.
NOTE: The following information is for wireless data presentation mode only.
Image display could be slow or not displayed smoothly if displaying a video clip
or animation. Refer to the frame-rate table below for reference:
Frame Rate of Wireless Presentation
Screen Variation % 1
Estimated frames per second 2
<5 %
30
<10%
28
<20%
26
<40%
25
<75%
22
<=100%
20
NOTE:
1 The percentage of screen variation is based on 1024 x 768. Example to display a
320 x 240 video clip on 1024 x 768 desktop, the screen variation is 9.8%.
Using Your Projector
65
2 Actual frame rate could be different depending on factors such as network
environment, image content, signal conditions, locations, and CPU performance.
3 Under clean WLAN environment using 802.11g connection, and no screen
stretching.
4 Compressed to 1024 x 768 and under 802.11g.
NOTE: Your computer will not enter S1 (standby mode) / S3 (sleep mode) / S4
(hibernate mode) when running a wireless, USB Display, or USB Viewer
presentation.
Using the Menu
Click
to display the menu.
WEB MANAGEMENT—Click to open the Web Management page. See "Managing the
Projector From Web Management" on page 81.
SEARCH FOR PROJECTOR—Click to search and connect to wireless projector.
MAKE APPLICATION TOKEN—Click to make application token. See "Make
Application Token" on page 100.
INFO—Click to display system information.
ABOUT—Click to display the application version.
EXIT—Click to close the application.
66
Using Your Projector
Presentation to Go (PtG) Installation
Minimum system requirements to install PtG are as follow:
Operating System:
- Windows
Microsoft Windows XP™ Home or Professional Service pack 2/3 (32-bit
recommended), Windows Vista 32-bit, or Windows® 7 Home or Professional
32-bit or 64-bit
- Office 2003 or Office 2007
NOTE: Presentation to Go (PtG) installation steps are the same for the 4220 and
4320 models.
In order to use your USB Viewer, you need to complete the steps below:
"Wireless and LAN" option and "Wireless connection" default are enabled.
1
Plug the USB Flash to your projector.
NOTE:
• Supports only the JPEG format photo within 10 MB x 40 M pixels.
• The PtG converter can convert your PowerPoint files into PtG files. See "PtG
Converter - Lite Application Software" on page 72.
• You can download the "PtG Converter - Lite" from the Dell Support site at:
support.dell.com.
2
At INPUT SOURCE menu, select Wireless/USB and then select USB Viewer
on the sub-menu. See "INPUT SOURCE WIRELESS/USB" on page 39.
NOTE:
1 When the Wireless and LAN function is disabled , Go to LAN Settings menu,
select the "Enabled" in the "Wireless and LAN" option to activate the Wireless
and LAN function.
2 When the Wireless connection is disconnected, Go to Wireless Settings
menu, select the "Connected" in the Wireless option to enable wireless
connection.
Using Your Projector
67
PtG Viewer
System will stay in this page when ready.
Photo Viewer
68
Using Your Projector
PtG/Photo Function Introduction
Show valid PtG and Photo files which are stored in the USB disk.
NOTE: If only one disk is detected, the system will skip this step.
PtG Overview
Using Your Projector
69
Photo Overview
NOTE: Supports 14 languages of photo files name format (Languages: English,
Dutch, French, German, Italian, Japanese, Korean, Polish, Portuguese, Russian,
Simplified Chinese, Spanish, Swedish, and Traditional Chinese).
Buttons-Introduction
Use the up, down, and left buttons to navigate and
control panel or remote control to select.
button on your projector's
Button
Up
Down
Left
Right
Enter
PtG function
Up
Down
Back
No function
Enter
PtG Playback
Pre Page
Next Page
Back
No function
Next Pause
Photo
function
Up
Down
Back
No function
Enter
Photo
Playback
Pre Page
Next Page
Back
No function
No
function
NOTE: If you enter the OSD menu while using PtG, PtG navigation by the up,
down, and left buttons will not function.
70
Using Your Projector
Set up PtG Converter - Lite
Please follow the on-screen instructions to complete the setup.
Using Your Projector
71
PtG Converter - Lite Application Software
Please launch the "PtG Converter - Lite". The below screen appears:
1
Click
2
Select the PowerPoint file you want to convert.
3
Click Browse button to select the storage location and then press OK.
to start conversion.
NOTE:
1 If your computer does not have MS PowerPoint installed, file convert will fail.
2 PtG converter only supports up to 20 pages.
3 PtG converter only supports conversion of .ppt files to .PtG files.
72
Using Your Projector
Audio Projection Installation
Audio Projection only supports the Wireless Display and LAN Display source.
Minimum system requirements as follow:
Operation System:
•
Windows
Microsoft Windows XP™ Home or Professional Service pack 2/3 (32-bit
recommended), Windows Vista 32-bit, or Windows® 7 Home or
Professional 32-bit or 64-bit
Minimum Hardware:
a
Intel® Core™ i5-460 MHz (2.53 GHz/Turbo 2.8 GHz) or greater
b
1 GB DDR3 VRAM independent graphics card or more
recommended
c
2 GB dual channel DDR3 SDRAM memory at 1066 MHz required
or more recommended
d
Gigabit Ethernet
e
Integrated 802.11 b/g/n Wi-Fi Device for a WLAN connection
NOTE: Audio Projection function not supports the MAC operation system.
NOTE: If your computer does not meet the minimum hardware requirements,
audio projection may have lag or noise. Meet the recommended system
requirements to have optimized performance of audio projection.
NOTE: Audio Projection Setting steps are the same for the 4220 and 4320
models.
Follow these steps to set up the audio projection function:
Using Your Projector
73
Enable Wireless or LAN on the Projector
1
Connect the power cable and turn on the projector by pressing the power
button.
2.1 If you choose the LAN connection mode, follow these steps to enable Wireless
and LAN function (default is Enabled): Advanced Settings
LAN Settings
Wireless and LAN
Enabled.
2.2 If you choose the wireless connection mode, follow these steps to enable
Wireless
wireless connection (default is Connected): Advanced Settings
Wireless
Connected.
Settings
NOTE: If your want to use the wireless connection for 4220 or 4320 projector,
need installed the optional wireless dongle. See "Installing the Optional
Wireless Dongle" on page 11.
74
Using Your Projector
3
Access the Input Source menu, select the Wireless/USB and then select the
Wireless Display on the sub-menu.
The Wireless Guide Screen shown below appears:
4
Take note of the LOGIN CODE, NETWORK NAME (SSID), and IP
ADDRESS. You will need these information to log in later.
Install the Dell Wireless Application Software on Your Computer
5
Connect the LAN cable to the projector and the computer.
Using Your Projector
75
NOTE: If your projector has installed the optional wireless dongle, you can also
select the wireless connection. See "Wireless Connection" on page 60.
NOTE: It is recommended that all proxies are turned off. (In Microsoft®
Windows 7: Click Control Panel
Settings)
6
Internet Options
Connections
LAN
"Wireless Application Software" is required if the Wireless or LAN is used for
the Audio Projection set-up. Please download and install the software the first
time you use Audio Projection. If it is already installed, skip Step 6 - 7.
NOTE: You only need to install the "Wireless Application Software" once.
7
76
Wireless Application Software download and installation steps refer to "Install
the Wireless Application Software" on page 60.
Using Your Projector
Launch the Wireless Application
8
Once the installation is complete, the program will launch automatically. Or
you can double-click the icon
or
on the desktop to start the
application.
NOTE:
1 If you choose LAN connection mode, click "Skip".
2 If you choose wireless connection mode, select your projector, and then
click "OK".
Login
9
To communicate with your projector, enter the Login Code (see Step 4), and
then click OK.
4220 Log in screen
4320 Log in screen
NOTE: If the IP Address is not detected, enter the IP Address displayed at the
bottom left corner of the wireless screen.
Using Your Projector
77
10
You are now logged into the 4220 or 4320 Wireless Application. Press the "Play"
button in the application to starting the LAN or wireless projection.
NOTE: You may use the controls to either project in full screen mode or in split
screen mode.
11
Press the "Audio Projection" button in the application to enable Audio
Projection function.
NOTE: Audio projector function need install extra driver, if your computer do
not install driver, will pop-up need install driver message on screen. You can
download the "extra driver" from the Dell Support site at support.dell.com.
12
78
Executing the Windows Media Player or others audio player software
(example: Winamp player...) on your computer.
Using Your Projector
Video Stream Installation
Video Stream only supports the Wireless Display and LAN Display source.
Minimum system requirements as follow:
Operation System:
•
Windows
Microsoft Windows XP™ Home or Professional Service pack 2/3 (32-bit
recommended), Windows Vista™ 32-bit, or Windows® 7 Home or
Professional 32-bit or 64-bit
•
MAC
MacBook Pro and above, MacOS 10.5 and above
Minimum Hardware:
a
Dual® Core™ 1.4 GHz or greater
b
64 MB VRAM independent graphics card or more recommended
c
2 GB DDR SDRAM memory or more recommended
d
Gigabit Ethernet
e
Integrated 802.11 b/g/n Wi-Fi Device for a WLAN connection
NOTE: If your computer does not meet the minimum hardware requirements,
video stream may have lag. Meet the recommended system requirements to
have optimized performance of the video stream.
NOTE: Video Stream Setting steps are the same for the 4220 and 4320 models.
Video Stream Support Format
File Format
Video Format
Audio Format
MP4
AVC, Mpeg4 visual, H.263
AAC-LC, MP3, AMR NB
MOV
AVC, Mpeg4 visual, H.263
AAC-LC, MP3
ASF
VC1
WMA
Using Your Projector
79
Enable Wireless or LAN on the Projector
Please refer to steps 1 to 4 of the Audio Projection Installation to enable wireless or
LAN feature.
Install the Dell Wireless Application Software on Your Computer
Please refer to steps 5 to 7 of the Audio Projection Installation to install the Dell
Wireless Application Software.
Launch the Wireless Application
Please refer to steps 8 of the Audio Projection Installation to launching the
Wireless Application.
Login
Please refer to steps 9 of the Audio Projection Installation to log-in the application.
1
You are now logged into the 4220 or 4320 Wireless Application. Click
"Video Mode" button switch to Video Mode screen.
2
Click
80
to select the video or music files and starting player.
Using Your Projector
Managing the Projector From Web
Management
Configuring the Network Setting
If the projector is connected to a network, you can access the projector using a web
browser. For configuring the network setting, refer to "LAN Settings" on page 50.
Accessing Web Management
Use Internet Explorer 5.0 and above or Firefox 1.5 and above and enter the IP
address. You can now access Web Management and manage the projector from a
remote location.
NOTE: Web management and set are the same for the 4220 and 4320 models.
Home Page
•
Access the Web Management Home page by entering the projector’s IP
address at the web browser. See "LAN Settings" on page 50.
•
Select the language for web management from the list.
•
Click any menu item on the left tab to access the page.
Using Your Projector
81
Download the Wireless Application Software
See also "Wireless Networking Installation" on page 57.
Click the Download button of the corresponding operating system of your
computer.
82
Using Your Projector
Conference Control
This allows you to host conference presentations from different sources without
using projector cables and lets you control how each presentation will appear on
screen.
NOTE: Without Conference Play Control, the last user to hit the "Play" button on
the application will take control of the full-screen projection.
Computer Name: Lists the computers logged for conference control.
Play Control: Click the buttons to control how each computer’s projection will
appear on screen.
•
Full screen projection — The presentation from the computer
occupies the whole screen.
•
Split 1 - The presenation from the computer appears on the upper
left corner of the screen.
•
Split 2- The presenation from the computer appears on the upper
right corner of the screen.
•
Split 3- The presenation from the computer appears on the lower left
corner of the screen.
•
Split 4- The presenation from the computer appears on the lower
right corner of the screen.
•
Stop - Projection from the computer is stopped.
IP Address: Shows each computer’s IP Address.
NOTE: To end the conference, click Home.
Using Your Projector
83
Managing Properties
Admin
An administrator password is required to access the Admin page.
•
84
Admin Password: Enter the administrator password and then click Login.
The default password is "admin". To change the password, see "Change
Passwords" on page 89.
Using Your Projector
System Status
Displays the Network Status, Connection Status, and Projector Status
information.
Using Your Projector
85
Network Status
See OSD section on page 50.
IP Setup
•
Choose Obtain an IP address automatically to assign an IP address to the
projector automatically, or Use the following IP address to assign an IP
address manually.
DHCP Server Setup
•
Choose Auto to automatically set up the Start IP, End IP, Subnet Mask,
Default Gateway, and DNS Server address from a DHCP server, or Disable
to disable this function.
Wireless Setup
•
86
Choose Enable to set up the Region, SSID, SSID Broadcast, Channel,
Encryption, and Key. Choose Disable to disable the wireless set up.
Using Your Projector
SSID: Up to maximum length of 32 characters.
Encryption: You can Disable WPA key or select one of 64-bit or 128-bit in
ASCII or HEX string.
Key: If Encryption is enabled, you have to set key value according to the
encryption mode you selected.
RADIUS Server Setup
•
Set up the IP address, Port, and Key information.
GateKeeper
•
There are three options:
All Pass: Allow users to access the office network via the wireless projector.
All Block: Block users from accessing the office network via the wireless
projector.
Internet Only: Block users from the office network, but still reserve Internet
connection capability.
Set Security For SNMP
•
Setup Write Community information.
Click the Apply button to save and apply changes. The projector must be restarted
for the changes to take effect.
Using Your Projector
87
Projection Setup
Projection Setup
•
Resolution: Allows you to select the resolution. Options are: XGA (1024 x
768) and WXGA (1280 x 800).
•
Login Code: Select how you want the login code to be generated by the
projector. There are three options:
•
Disable: Login code will not be required when logging in to the system.
•
Random: Default is Random. Login code will be randomly generated.
•
Use the following code: Enter a 4-digit code. This code will be used to
log in to the system.
Projector Setup
•
Set up the Model Name, Projector Name, Location, and Contact
information (up to 21 characters for each field).
Click the Apply button to save and apply changes. The projector must be restarted
for the changes to take effect.
88
Using Your Projector
Change Passwords
This page allows you to change the administrator password.
•
Enter New Password: Enter the new password.
•
Confirm New Password: Enter the password again and click Apply.
NOTE: Contact Dell if you forget your administrator password.
Using Your Projector
89
Reset to Default
Click the Apply button to restore the wireless/network setup to its factory default
settings.
90
Using Your Projector
Firmware Upgrade
Use the Firmware Upgrade page to update your projector’s wireless firmware.
NOTE: Please disable and enable wireless/network using the OSD to restart
the network card for the projector after firmware upgrade is successful.
To start the firmware update, follow these steps:
1
Press Browse to select the file to update.
2
Click the Update button to start. Wait while the system updates the firmware
in your device.
CAUTION: Do not interrupt the update process as this may cause the system to
crash!
3
Click OK when the update is complete.
Using Your Projector
91
Projector Control Panel
Projector Information
•
Projector Status: There are five status: Lamp On, Standby, Power Saving,
Cooling, and Warming up. Click Refresh to refresh the status and control
settings.
•
Power Saving: Power Saving can be set to Off, 30, 60, 90, or 120 minutes. For
more information, see "Power Saving" on page 55.
•
Alert Status: There are three alert states: Lamp warning, Low lamp life, and
Temperature warning. Your projector might lock up in the protection mode
if any of the alerts are activated. To exit the protection mode, click Clear to
clear the Alert Status before you power on your projector.
92
Using Your Projector
Image Control
•
Operation Mode: Allows you to select the operation mode. The two options
are: Normal Mode and ECO Mode.
•
Projector Mode: Allows you to select the projector mode, depending on how
the projector is mounted. There are four projection modes: Front
Projection-Desktop, Front Projection-Ceiling Mount, Rear ProjectionDesktop, and Rear Projection-Ceiling Mount.
•
Source Select: The Source Select menu allows you to select your projector’s
input source. You can select VGA-A, VGA-B, S-Video, Composite Video,
HDMI, Wireless Display, USB Display, or USB Viewer.
•
Video Mode: Select a mode to optimize the display image based on how the
projector is being used:
- Presentation: Best for presentation slides.
- Bright: Maximum brightness and contrast.
- Movie: For viewing movies and photos
- sRGB: Provides a more accurate color representation.
- Custom: User-preferred settings.
•
Blank Screen: You can select On or Off.
•
Aspect Ratio: Allows you to select the aspect ratio to adjust how the image
appears.
•
Brightness: Select value to adjust the brightness of the image.
•
Contrast: Select value to adjust the display contrast.
Click the Auto Adjust button to adjust the settings automatically.
Audio Control
• Audio Input: Select the input source. Options are: Audio-A, Audio-B,
Audio-C, HDMI, and Wireless/LAN.
•
Volume: Select the value (0~20) for audio volume.
•
Speaker: Select On to enable the audio function or select Off to disable the
audio function.
Click the Factory Reset button to restore the factory default settings.
Using Your Projector
93
Alert Setting
E-mail Alert
•
E-mail Alert: You can set whether to be notified by email (Enable) or not
(Disable).
•
To/CC/From: You can enter email address of sender (From) and recipients
(To/Cc) to receive notification when an abnormality or warning occurs.
•
Subject: You can enter the subject line of the email.
Click the E-mail Alert Test button to test the e-mail alert settings.
SMTP Setting
•
Out going SMTP server, User name, and Password should be provided by
your network administrator or MIS.
Alert Condition
•
You can select the abnormalities or warnings to be notified by email. When
any of the alert conditions occur, an email will be sent to the recipients
(To/Cc).
Click the Save button to save the settings.
NOTE: E-mail alert is designed to work with a standard SMTP server using the
default 25 port. It does not support encryption and authentication (SSL or TLS).
94
Using Your Projector
Reboot System
Click Reboot to reboot the system.
Crestron
For Crestron function.
Using Your Projector
95
FAQS:
I would like to remotely access
the projector via the Internet.
What is the best setting for the
browser?
To have the best setting for the browser, please
follow the below steps:
1 Open Control Panel
Internet Options
General tab
Temporary Internet Files
Settings
Select Every visit to the pages.
2 Some firewall or anti-virus may block the
HTTP application. If possible, turn off the
firewall or anti-virus.
I would like to remotely access The following are the TCP/IP socket ports
the projector via Internet. What which the projector uses.
socket port number should I
UDP/TCP
Port
Description
open for it in the firewall?
Number
Why am I unable to access the
projector via the Internet?
96
Using Your Projector
TCP
80
Web configuration
(HTTP)
UDP/TCP
25
SMTP: used for email
routing between mail
servers
UDP/TCP
161
SNMP: Simple
Network
Management
Protocol
UDP
9131
AMX: used for AMX
discovery
1 Check whether your computer/laptop is
connected to the Internet.
2 Check with your MIS or network
administrator whether your computer/laptop
is in the same subnet.
Why am I unable to access the
SMTP server?
Why am I unable to receive the
test alert email even though the
projector already indicates the
test mail is already sent?
1 Check with your MIS or network
administrator whether the SMTP server
function is open for the projector and the IP
assigned to the projector is allowed to access
the SMTP server. The projector’s SMTP
socket port number is 25, this cannot be
changed.
2 Check if the outgoing SMTP server, user
name, and password are set correctly.
3 Some SMTP servers will check whether the
mail address of "From" correlates with the
"User name" and "Password". For example,
you use test@dell.com as the mail address in
"From". You should also use test@dell.com
account information for the User name and
the password to log in the SMTP server.
It could be because the SMTP server
recognized the alert mail as a spam mail or
because of the SMTP server restriction. Check
with your MIS or network administrator for
the SMTP server’s setting.
Using Your Projector
97
Firewall Configuration and FAQ
Q: Why can’t I access the Web Management Page?
A: Your computer’s firewall configuration may prevent you from accessing the
Web Management Web Page. Please refer to the following configuration
settings:
Firewall Protection
McAfee Security
Center
Norton AntiVirus
Sygate Personal
Firewall
98
Configuration
1
Launch McAfee Security Center (Start > All
Programs > McAfee > McAfee Security Center).
2
On the personal firewall plus tab, click View the
Internet Applications List.
3
Find and select Dell 4220 or 4320 Projector from the
list.
4
Right-click on its Permissions column.
5
Select Allow Full Access from the pop-up menu.
1
Open Norton AntiVirus (Start > All Programs >
Norton AntiVirus > Norton AntiVirus).
2
Click Options menu, then select Norton AntiVirus.
3
On the Status page, select Internet Worm
Protection.
4
Find and select Dell 4220 or 4320 Projector from the
list of programs.
5
Right-click on its Internet Access column.
6
Select Permit All from the pop-up menu.
7
Click OK.
1
Open Sygate Personal Firewall (Start > All Programs
> Sygate > Sygate Personal Firewall).
2
From the Running Applications list, find and
right-click on Dell 4220 or 4320 Projector.
3
Select Allow from the pop-up menu.
Using Your Projector
Firewall Protection
Windows Firewall
Zone Alarm
Configuration
1
Open Windows Firewall (Start > All Programs >
Control Panel). Double-click on Windows Firewall.
2
On the General tab, uncheck Don’t allow
exceptions.
3
On the Exceptions tab, click the Add Program...
button.
4
Find and select Dell 4220 or 4320 Projector from the
list of programs, then click OK.
5
Click OK to confirm exceptions settings.
1
Open Zone Alarm Firewall (Start > All Programs >
Zone Labs > Zone Labs Center).
2
On the Program Control page, find and select
Dell 4220 or 4320 Projector from the list.
3
Right-click on its Access-Trusted column.
4
Select Allow from the pop-up menu.
5
Right-click and select Allow for the Access-Internet,
Server-Trusted, and Server-Internet columns.
Using Your Projector
99
Make Application Token
The Application Token lets you perform Plug and Show using a USB token.
1
From the application software, click
2
The following screen appears. Click Next.
3
Plug a flash drive into any of the USB ports on your computer. Select the drive
from the list, then click Next.
4
Click Finish to close the wizard.
100
Using Your Projector
> Make Application Token.
Troubleshooting Your Projector
4
If you experience problems with your projector, see the following troubleshooting
tips. If the problem persists, contact Dell™ (see Contacting Dell™ on page 115).
Problem
Possible Solution
No image appears on the
screen
• Ensure that the lens cap is removed and the
projector is turned on.
• Ensure that you have chosen the correct
input source on the INPUT SOURCE menu.
• Ensure the external graphics port is enabled.
If you are using a Dell™ laptop computer,
press
(Fn+F8). For other
computers, see your respective
documentation. If images are not displayed
properly, please upgrade the video driver of
your computer. For Dell computers, see
support.dell.com.
• Ensure that all the cables are securely
connected. See "Connecting Your Projector"
on page 10.
• Ensure that the pins of the connectors are
not bent or broken.
• Ensure that the lamp is securely installed
(see "Changing the Lamp" on page 106).
• Use Test Pattern in the Projector Settings of
the Advanced Settings menu. Ensure that
the colors of the test pattern are correct.
Troubleshooting Your Projector
101
Problem (continued)
Partial, scrolling, or
incorrectly displayed image
Possible Solution (continued)
1 Press the Auto Adjust button on the remote
control or the control panel.
2 If you are using a Dell™ portable computer,
set the resolution of the computer to WXGA
(1280 x 800) or XGA (1024 x 768):
a Right-click the unused portion of your
Microsoft® Windows® desktop, click
Properties, and then select Settings tab.
b Verify that the setting is 1280 x 800 or
1024 x 768 pixels for the external monitor
port.
c Press
(Fn+F8).
If you experience difficulty in changing
resolutions, or if your monitor freezes, restart
all the equipment and the projector.
If you are not using a Dell™ portable
computer, see your documentation. If images
are not displayed properly, please upgrade the
video driver of your computer. For a Dell
computer, see support.dell.com.
The screen does not display
your presentation
If you are using a portable computer, press
(Fn+F8).
Image is unstable or flickering Adjust the tracking in the OSD Display
Settings of the Advanced Settings menu (in
PC Mode only).
Image has vertical flickering
bar
Adjust the frequency in the OSD Display
Settings of the Advanced Settings menu (in
PC Mode only).
Image color is incorrect
• If the display receives the wrong signal
output from the graphics card, please set the
signal type to RGB in the OSD Image
Settings of the Advanced Settings tab.
• Use Test Pattern in the Projector Settings of
the Advanced Settings menu. Ensure that
the colors of the test pattern are correct.
102
Troubleshooting Your Projector
Problem (continued)
Image is out of focus
Possible Solution (continued)
1 Adjust the focus ring on the projector lens.
2 Ensure that the projection screen is within
the required distance from the projector
(3.94 ft [1.2 m] to 32.81 ft [10 m]).
The image is stretched when
displaying a 16:9 DVD
The projector automatically detects the input
signal format. It will maintain the aspect ratio
of the projected image according to input
signal format with an Original setting.
If the image is still stretched, adjust the aspect
ratio in the Display Settings of the Advanced
Settings menu in the OSD.
Image is reversed
Select Projector Settings of the Advanced
Settings from the OSD and adjust the
projector mode.
Lamp is burned out or makes
a popping sound
When the lamp reaches its end of life, it may
burn out and may make a loud popping sound.
If this occurs, the projector does not turn back
on. To replace the lamp, see "Changing the
Lamp" on page 106.
LAMP light is solid amber
If the LAMP light is solid amber, replace the
lamp.
LAMP light is blinking amber
If the LAMP light is blinking amber, the lamp
module connection may be disrupted. Please
check the lamp module and ensure that it is
properly installed.
If the LAMP light and the Power light are
blinking amber, the lamp driver has failed and
the projector will automatically shut down.
If the LAMP and TEMP lights are blinking
amber and the Power light is solid blue, the
color wheel has failed and the projector will
automatically shut down.
To clear the protection mode, press and hold
the POWER button for 10 seconds.
Troubleshooting Your Projector
103
Problem (continued)
Possible Solution (continued)
TEMP light is solid amber
The projector has overheated. The display
automatically shuts down. Turn the display on
again after the projector cools down. If the
problem persists, contact Dell™.
TEMP light is blinking amber If the projector fan fails, the projector will
automatically shut down. Try to clear the
projector mode by pressing and holding the
Power button for 10 seconds. Please wait for
about 5 minutes and try to power up again. If
the problem persists, contact Dell™.
The OSD does not appear on
the screen
Try to press the Menu button on the panel for
15 seconds to unlock the OSD. Check the
Menu Lock on page 52.
The remote control is not
operating smoothly or works
only within a limited range
The battery may be low. Check if the laser
beam transmitted from the remote is too dim.
If so, replace with two new AAA batteries.
104
Troubleshooting Your Projector
Guiding Signals
Control Buttons
Projector Status
Description
Indicator
Power
TEMP
(Amber)
LAMP
(Amber)
Standby mode
Projector in Standby mode. Ready to power
on.
BLUE
Flashing
OFF
OFF
Warming up
mode
Projector takes some time to warm up and
power on.
BLUE
OFF
OFF
Lamp on
Projector in Normal mode, ready to display
an image.
Note: The OSD menu is not accessed.
BLUE
OFF
OFF
Cooling mode
Projector is cooling to shutdown.
BLUE
OFF
OFF
Cooling before
Power Saving
mode
The projector takes 60 seconds to cool
down before entering Power Saving mode.
AMBER
OFF
OFF
Projector
overheated
Air vents might be blocked or ambient
temperature may be above 35 ºC. The
projector automatically shuts down. Ensure
that the air vents are not blocked and that
the ambient temperature is within
operational range. If the problem persists,
contact Dell.
OFF
AMBER
OFF
Lamp driver
overheated
The lamp driver is overheated. The air
vents may be blocked. The projector
automatically shuts down. Turn the display
on again after the projector cools down. If
the problem persists, contact Dell.
AMBER
AMBER
OFF
Fan breakdown
One of the fans has failed. The projector
automatically shuts down. If the problem
persists, contact Dell.
ÒFF
AMBER
Flashing
OFF
Lamp driver
breakdown
The lamp driver has failed. The projector
automatically shuts down. Unplug the
power cord after three minutes and then
turn the display on again. If this problem
persists, contact Dell.
AMBER
Flashing
OFF
AMBER
Flashing
Color Wheel
breakdown
Color wheel cannot start. The projector has
failed and the projector automatically shuts
down. Unplug the power cord after three
minutes and then turn on the projector. If
this problem persists, contact Dell.
BLUE
AMBER
Flashing
AMBER
Flashing
Lamp failure
Lamp is defective. Replace the lamp.
OFF
OFF
AMBER
Fault - DC supply
(+12V)
Power supply has been interrupted. The
projector automatically shuts down.
Unplug the power cord after three minutes
and then turn on the projector. If this
problem persists, contact Dell.
AMBER
Flashing
AMBER
AMBER
Lamp module
connection failed
Lamp module connection may be
disrupted. Check the lamp module and
ensure that it is properly installed. If the
problem persists, contact Dell.
OFF
OFF
AMBER
Flashing
Troubleshooting Your Projector
105
Changing the Lamp
CAUTION: Before you begin any of the procedures in this section, follow the
Safety Instructions as described on page 8.
Replace the lamp when the message "Lamp is approaching the end of its useful
life in the operation. Replacement suggested! www.dell.com/lamps" appears
on the screen. If this problem persists after replacing the lamp, contact Dell™. For
more information, see Contacting Dell™on page 115.
CAUTION: Use an original lamp to ensure safe and optimal working condition
of your projector.
CAUTION: The lamp becomes very hot when in use. Do not attempt to replace
the lamp until the projector has been allowed to cool down for at least 30 minutes.
CAUTION: Do not touch the bulb or the lamp glass at any time. Projector lamps
are very fragile and may shatter if touched. The shattered glass pieces are
sharp and can cause injury.
CAUTION: If the lamp shatters, remove all broken pieces from the projector
and dispose or recycle according to state, local, or federal law. For more
information see www.dell.com/hg.
1 Turn off the projector and disconnect the power cord.
2 Let the projector cool for at least 30 minutes.
3 Loosen the two screws that secure the
lamp cover, and remove the cover.
4 Loosen the two screws that secure the
lamp.
5 Pull the lamp up by its metal handle.
NOTE: Dell™ may require lamps
replaced under warranty to be returned
to Dell™. Otherwise, contact your local
waste disposal agency for the address
of the nearest deposit site.
6 Replace with the new lamp.
7 Tighten the two screws that secure the
lamp.
8 Replace the lamp cover and tighten the
two screws.
9 Reset the lamp usage time by selecting "Yes" for Lamp Reset in the OSD Power
Settings of the Advanced Setting menu (see Power Settings of the Advanced
106
Troubleshooting Your Projector
Setting menu on page 54). When a new lamp module has been changed, the
projector will automatically detect and reset the lamp hours.
CAUTION: Lamp Disposal (for the US only)
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE
RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE, OR FEDERAL
LAWS. FOR MORE INFORMATION, GO TO WWW.DELL.COM/HG OR CONTACT
THE ELECTRONIC INDUSTRIES ALLIANCE AT WWW.EIAE.ORG. FOR
LAMP-SPECIFIC DISPOSAL INFORMATION, CHECK WWW.LAMPRECYCLE.ORG.
Troubleshooting Your Projector
107
Specifications
Light Valve
5
4220: 0.55" XGA S450 DMD, DarkChip3™
4320: 0.65" WXGA S450 DMD, DarkChip3™
Brightness
4220: 4100 ANSI Lumens (Max.)
4320: 4300 ANSI Lumens (Max.)
Contrast Ratio
2000:1 Typical (Full On/Full Off)
Uniformity
80% Typical (Japan Standard - JBMA)
Number of Pixels
4220: 1024 x 768 (XGA)
4320: 1280 x 800 (WXGA)
Displayable Color
1.07 billion colors
Color Wheel Speed
2X
Projection Lens
F-Stop: F/ 2.4~2.66
Focal length, f=18.2~21.8 mm
1.2X manual Zoom Lens, Fix
4220: Throw ratio =1.6~1.92 wide and tele
4320: Throw ratio =1.28~1.536 wide and tele
Projection Screen Size
4220: 30.8~307 inches (diagonal)
1X for 3D Display
4320: 36.3~362 inches (diagonal)
Projection Distance
3.94~32.81 ft (1.2 m~10 m)
Video Compatibility
Composite Video / S-Video: NTSC (J, M, 4.43), PAL
(B, D, G, H, I, M, N, Nc, 60), SECAM (B, D, G, K,
K1, L)
Component Video input via VGA: 1080i, 720p,
576i/p, 480i/p
Component Video input via HDMI: 1080p, 720p,
576i/p, 480i/p
Power Supply
108
Specifications
Universal AC 100-240 50-60 Hz with PFC input
Power Consumption
Normal mode: 375 W ± 10% @ 110 Vac
(Network On)
Eco mode: 320 W ± 10% @ 110 Vac (Network On)
Power saving mode: <10 W (Wireless and
Network On)
Standby mode: < 0.5 W (Network, VGA_Out, and
Wireless Off)
Audio
2 speakers x 5 watt RMS
Noise Level
35 dB(A) Normal mode, 32 dB(A) Eco mode
Weight
6.4 lb (2.9 kg) ± 0.05 lb
Dimensions (W x H x D)
11.26 x 4.33 x 9.76 inches (286 x 110 x 247.8 mm)
Environmental
Operating temperature: 5 oC - 35 oC (41 oF- 95 oF)
Humidity: 80 % maximum
Storage temperature: 0 oC to 60 oC (32 oF to 140 oF)
Humidity: 90 % maximum
Shipping temperature: -20 oC to 60 oC
(-4 oF to 140 oF)
Humidity: 90 % maximum
I/O Connectors
Power: One AC power socket (3-pin - C14 inlet)
VGA input: Two 15-pin D-sub connectors (Blue),
VGA-A and VGA-B, for analog RGB/Component
input signals.
VGA output: One 15-pin D-sub connector (Black)
for VGA-A loop through.
S-Video input: One standard 4-pin min-DIN
S-Video connector for Y/C signal.
Specifications
109
Composite Video input: One Yellow RCA jack for
CVBS signal.
HDMI input: One HDMI connector for supporting
HDMI 1.3. HDCP compliant.
Analog Audio input: Two 3.5 mm stereo mini phone
jack (Blue) and one pair of RCA connector
(Red/White).
Variable audio output: One 3.5 mm stereo mini
phone jack (Green).
USB (type A) port: One USB connector for
Photo/PtG viewer (JPG/PPT format).
USB (type B) port: One mini USB slave for remote
support and One USB connector for supporting
USB Display.
RS232 port: One mini-DIN 6-pin for RS232
communication.
RJ45 port: One RJ45 connector for control of
projector through network and LAN Display.
12 V output: One 12 V DC / 200 mA max. relay
output for driving automatic screen.
Wireless Dongle
Wireless Standard: IEEE802.11b/g/n
Wireless: One WiFi USB (type A) connector for
supporting wireless dongle (USB interface,
Optional).
OS environment: Windows 7/Vista/XP/2000, MAC
OS X
Support: Presentation slides and projector control.
Allow connection up to 30 users at the same time.
4-to-1 split screen. Allow four presentation slides to
be projected on screen.
Conference Control mode.
Supports Audio Projection (need to install extra
driver)
Lamp
110
Philips 300 W user-replaceable lamp (up to 2500
hours in eco mode)
Specifications
NOTE: The lamp life rating for any projector is a measure of brightness
degradation only, and is not a specification for the time it takes a lamp to fail
and cease light output. Lamp life is defined as the time it takes for more than
50 percent of a lamp sample population to have brightness decrease by
approximately 50 percent of the rated lumens for the specified lamp. The lamp
life rating is not guaranteed in any way. The actual operating life span of a
projector lamp will vary according to operating conditions and usage patterns.
Usage of a projector in stressful conditions which may include dusty
environments, under high temperatures, many hours per day, and abrupt
powering-off will most likely result in a lamp’s shortened operating life span or
possible lamp failure.
Specifications
111
RS232 Pin Assignment
RS232 Protocol
•
Communication Settings
Connection settings
Value
Baud Rate
19,200
Data Bits
8
Parity
None
Stop Bits
1
•
Command types
•
Control command Syntax (From PC to Projector)
To pop up the OSD menu and adjust the settings.
[H][AC][SoP][CRC][ID][SoM][COMMAND]
•
Example: Power ON Command (Send low byte firstly)
--> 0xBE, 0xEF, 0x10, 0x05, 0x00, 0xC6, 0xFF, 0x11, 0x11, 0x01, 0x00, 0x01
•
Control Commands List
To view the latest RS232 code, go to the Dell Support site at: support.dell.com.
112
Specifications
Compatibility Modes (Analog/Digital)
Resolution
Refresh Rate (Hz)
Hsync Frequency
(KHz)
Pixel Clock (MHz)
640 x 350
70.087
31.469
25.175
640 x 480
59.940
31.469
25.175
640 x 480 p60
59.940
31.469
25.175
720 x 480 p60
59.940
31.469
27.000
720 x 576 p50
50.000
31.250
27.000
720 x 400
70.087
31.469
28.322
640 x 480
75.000
37.500
31.500
848 x 480
60.000
31.020
33.750
640 x 480
85.008
43.269
36.000
800 x 600
60.317
37.879
40.000
800 x 600
75.000
46.875
49.500
800 x 600
85.061
53.674
56.250
1024 x 768
60.004
48.363
65.000
1280 x 720 p50
50.000
37.500
74.250
1280 x 720 p60
60.000
45.000
74.250
1920 x 1080 i50
50.000
28.125
74.250
1920 x 1080 i60
60.000
33.750
74.250
1280 x 720
59.855
44.772
74.500
1024 x 768
75.029
60.023
78.750
1280 x 800
59.810
49.702
83.500
1366 x 768
59.790
47.712
85.500
1360 x 768
60.015
47.712
85.500
1024 x 768
84.997
68.677
94.500
1440 x 900
59.887
55.935
106.500
1152 x 864
75.000
67.500
108.000
1280 x 960
60.000
60.000
108.000
1280 x 1024
60.020
63.981
108.000
1152 x 864
85.000
77.095
119.651
1400 x 1050
59.978
65.317
121.750
1280 X 800
84.880
71.554
122.500
1280 x 1024
75.025
79.976
135.000
1440 X 900
74.984
70.635
136.750
1680 x 1050
59.954
65.290
146.250
1280 x 960
85.002
85.938
148.500
1920 x 1080
60.000
67.500
148.500
1400 X 1050
74.867
82.278
156.000
1280 x 1024
85.024
91.146
157.000
1440 X 900
84.842
80.430
157.000
1600 x 1200
60.000
75.000
162.000
Specifications
113
114
800 x 600
119.972
76.302
73.250
1024 x 768
119.989
97.551
115.500
1280 x 720
120.000
101.563
146.250
Specifications
Contacting Dell
For customers in the United States, call 800-WWW-DELL (800-9993355).
NOTE: If you do not have an active Internet connection, you can find contact
information on your purchase invoice, packing slip, bill, or Dell product catalog.
Dell™ provides several online and telephone-based support and service
options. Availability varies by country and product, and some services may
not be available in your area. To contact Dell for sales, technical support,
or customer service issues:
1
Visit support.dell.com.
2
Verify your country or region in the Choose A Country/Region dropdown menu at the bottom of the page.
3
Click Contact Us on the left side of the page.
4
Select the appropriate service or support link based on your need.
5
Choose the method of contacting Dell that is convenient for you.
Contacting Dell
115
Appendix: Glossary
ANSI LUMENS — A standard for measuring the brightness. It is calculated by
dividing a square meter image into nine equal rectangles, measuring the lux (or
brightness) reading at the center of each rectangle, and averaging these nine
points.
ASPECT RATIO — The most popular aspect ratio is 4:3 (4 by 3). Early television and
computer video formats are in a 4:3 aspect ratio, which means that the width of
the image is 4/3 times the height.
Brightness — The amount of light emitted from a display or projection display or
projection device. The brightness of projector is measured by ANSI lumens.
Color Temperature — The color appearance of white light. Low color
temperature implies warmer (more yellow/red) light while high color temperature
implies a colder (more blue) light. The standard unit for color temperature is
Kelvin (K).
Component Video — A method of delivering quality video in a format that
consists of the luminance signal and two separate chrominance signals and are
defined as Y'Pb'Pr' for analog component and Y'Cb'Cr' for digital component.
Component video is available on DVD players.
Composite Video — A video signal that combines the luma (brightness), chroma
(color), burst (color reference), and sync (horizontal and vertical synchronizing
signals) into a signal waveform carried on a single wire pair. There are three kinds
of formats, namely, NTSC, PAL, and SECAM.
Compressed Resolution — If the input images are of higher resolution than the
native resolution of the projector, the resulting image will be scaled to fit the
native resolution of the projector. The nature of compression in a digital device
means that some image content is lost.
Contrast Ratio — Range of light and dark values in a picture, or the ratio between
their maximum and minimum values. There are two methods used by the
projection industry to measure the ratio:
1 Full On/Off — measures the ratio of the light output of an all white image (full
on) and the light output of an all black (full off) image.
2 ANSI — measures a pattern of 16 alternating black and white rectangles. The
average light output from the white rectangles is divided by the average light
output of the black rectangles to determine the ANSI contrast ratio.
Full On/Off contrast is always a larger number than ANSI contrast for the same
projector.
116
Glossary
dB — decibel — A unit used to express relative difference in power or intensity,
usually between two acoustic or electric signals, equal to ten times the common
logarithm of the ratio of the two levels.
Diagonal Screen — A method of measuring the size of a screen or a projected
image. It measures from one corner to the opposite corner. A 9 ft high and 12 ft
wide, screen has a diagonal of 15 ft. This document assumes that the diagonal
dimensions are for the traditional 4:3 ratio of a computer image as per the example
above.
DHCP — Dynamic Host Configuration Protocol — A network protocol that
enables a server to automatically assign a TCP/IP address to a device.
DLP® — Digital Light Processing™ — Reflective display technology developed by
Texas Instruments, using small manipulated mirrors. Light passing through a color
filter is sent to the DLP mirrors which arrange the RGB colors into a picture
projected onto screen, also known as DMD.
DMD — Digital Micro-Mirror Device — Each DMD consists of thousands of
tilting, microscopic aluminum alloy mirrors mounted on a hidden yoke.
DNS — Domain Name System — An Internet service that translates domain
names into IP addresses.
Focal Length — The distance from the surface of a lens to its focal point.
Frequency — It is the rate of repetition in cycles per seconds of electrical signals.
Measured in Hz (Hertz).
HDCP — High-Bandwidth Digital-Content Protection — A specification
developed by Intel™ Corporation to protect digital entertainment across digital
interface, such as DVI, HDMI.
HDMI — High-Definition Multimedia Interface — HDMI carries both
uncompressed high definition video along with digital audio and device control
data in a single connector.
Hz (Hertz) — Unit of frequency.
IEEE802.11 — A set of standards for wireless local are network (WLAN)
communication. 802.11b/g/n uses the 2.4 GHz band.
Keystone Correction — Device that will correct an image of the distortion
(usually a wide-top narrow-bottom effect) of a projected image caused by
improper projector to screen angle.
Maximum Distance — The distance from a screen the projector can be to cast an
image that is usable (bright enough) in a fully darkened room.
Maximum Image Size — The largest image a projector can throw in a darkened
room. This is usually limited by focal range of the optics.
Glossary
117
Minimum Distance — The closest position that a projector can focus an image
onto a screen.
NTSC — National Television Standards Committee. North American standard for
video and broadcasting, with a video format of 525 lines at 30 frames per second.
PAL — Phase Alternating Line. A European broadcast standard for video and
broadcasting, with a video format of 625 lines at 25 frames per second.
Reverse Image — Feature that allows you to flip the image horizontally. When
used in a normal forward projection environment text, graphics, etc. are
backwards. Reverse image is used for rear projection.
RGB — Red, Green, Blue — typically used to describe a monitor that requires
separate signals for each of the three colors.
S-Video — A video transmission standard that uses a 4-pin mini-DIN connector
to send video information on two signal wires called luminance (brightness, Y) and
chrominance (color, C). S-Video is also referred to as Y/C.
SECAM — A French and international broadcast standard for video and
broadcasting, closely related to PAL but with a different method of sending color
information.
SSID — Service Set Identifiers — A name used to identify the particular wireless
LAN to which a user wants to connect.
SVGA — Super Video Graphics Array — 800 x 600 pixels count.
SXGA — Super Extended Graphics Array, — 1280 x 1024 pixels count.
UXGA — Ultra Extended Graphics Array — 1600 x 1200 pixels count.
VGA — Video Graphics Array — 640 x 480 pixels count.
WEP — Wired Equivalent Privacy — This is a method for encrypting
communication data. The encryption key is created and notified only to the
communicating user, so the communication data cannot be decrypted by a third
party.
XGA — Extended Video Graphics Array — 1024 x 768 pixels count.
WXGA — Wide Extended Graphics Array — 1280 x 800 pixels count.
Zoom Lens — Lens with a variable focal length that allows operator to move the
view in or out making the image smaller or larger.
Zoom Lens Ratio — Is the ratio between the smallest and largest image a lens can
the project from a fixed distance. For example, a 1.4:1 zoom lens ratio means that
a 10 foot image without zoom would be a 14 foot image with full zoom.
118
Glossary
Index
A
Adjusting the Projected Image 25
Elevator button 25
lower the projector
Elevator foot 25
Tilt adjustment wheel 25
Lowering the Projector Height
25
Raising the Projector Height 25
Adjusting the Projector Zoom and
Focus 26
Focus ring 26
Zoom tab 26
C
Changing the Lamp 106
Connecting the Projector
12 V DC Plug 22
Composite Video cable 18
Connecting a Computer with a
RS232 cable 14, 15
Connecting with a Component
Cable 19
Connecting with a Composite
Cable 18
Connecting with an HDMI
Cable 20
Connecting with an S-video
Cable 17
HDMI cable 20, 21, 23
Motorized projection screen 22
Power cord 12, 13, 14, 15, 17,
18, 19, 20, 21, 22, 23
RS232 cable 14
S-Video cable 17
To Computer 12
USB to USB cable 12
USB-A to USB-B cable 15
VGA to VGA cable 12, 13
VGA to YPbPr cable 19
Connection Ports
+12 V DC out connector 10
Audio output connector 10
Audio-A input connector 10
Audio-B input connector 10
Audio-C left-channel input
connector 10
Audio-C right channel input
connector 10
Composite Video connector 10
HDMI connector 10
Mini USB (Mini Type B)
connector for remote
control 10
Power code connector 10
RJ45 connector 10
RS232 connector 10
Security cable slot 10
S-Video connector 10
USB Type A connector for USB
Viewer 10
USB Type B connector for USB
Index
119
Display 10
VGA-A input (D-sub) connector
10
VGA-A output (monitor
loop-through) 10
VGA-B input (D-sub) connector
10
WiFi USB Type A connector 10
Contact Dell 7, 104, 106
Control Panel 31
D
Dell
contacting 115
P
phone numbers 115
Powering On/Off the Projector
Powering Off the Projector 24
Powering On the Projector 24
R
Remote Control 33
IR receiver 32
M
Main Unit 8
Control panel 8
Elevator button for height
adjustments 8
Focus tab 8
IR receivers 8
Lens 8
Lens cap 8
Zoom tab 8
O
On-Screen Display 38
ADVANCED SETTINGS 41
AUDIO INPUT 41
AUTO ADJUST 39
BRIGHTNESS/CONTRAST 40
HELP 56
120
INPUT SOURCE 38
INPUT SOURCE MULTIPLE
DISPLAY 39
LANGUAGE 56
VIDEO MODE 40
VOLUME 41
Index
S
Specifications
Audio 109
Brightness 108
Color Wheel Speed 108
Contrast Ratio 108
Dimensions 109
Displayable Color 108
Environmental 109
I/O Connectors 109
Light Valve 108
Noise Level 109
Number of Pixels 108
Power Consumption 109
Power Supply 108
Projection Distance 108
Projection Lens 108
Projection Screen Size 108
RS232 Protocol 112
Uniformity 108
Video Compatibility 108
Weight 109
support
contacting Dell 115
T
telephone numbers 115
Troubleshooting 101
Contact Dell 101
V
VGA-B input (D-sub) connector
10
Index
121
Download PDF