Philips Micro music system DCM2060 User manual

Register your product and get support at
www.philips.com/welcome
EN
User manual
ZH-CN
用户手册
DCM2060_93_UM_V1.1.indb 1
DCM2060
2011/8/31 15:18:42
1Important
Know these safety symbols
Hearing Safety
2 Your Micro System
Introduction
What’s in the box
Overview of the main unit
Overview of the remote control
4
4
5
6
6
6
7
8
3 Get started
10
10
10
10
11
11
11
4Play
12
12
12
12
13
14
14
5 Listen to FM radio
14
14
14
15
15
15
15
6 Other features
16
16
16
16
16
Placement
Connect FM antenna
Prepare the remote control
Connect power
Set clock
Turn on
Play disc
Play from USB
Play from iPod/iPhone/iPad
Play options
Adjust sound
Display different information
Auto install FM radio stations
Tune to FM radio stations
Program FM radio stations automatically
Program FM radio stations manually
Select a preset radio station
Select stereo/mono broadcast
Set the alarm timer
Set the sleep timer
Listen through the headphone
Play from external audio device
7 Product information
17
17
18
18
8Troubleshooting
19
9Notice
20
Specifications
USB playability information
Supported MP3 disc formats
EN
DCM2060_93_UM_V1.1.indb 3
English
Contents
3
2011/8/31 15:18:42
1Important
•
•
•
•
•
•
•
•
•
•
•
•
•
•
4
Read these instructions.
Follow all instructions.
Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
Do not install near any heat sources such
as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that
produce heat.
Protect the power cord from being
walked on or pinched, particularly at
plugs, convenience receptacles, and the
point where they exit from the unit.
Only use attachments/accessories
specified by the manufacturer.
Unplug this unit during lightning storms or
when unused for long periods of time.
Refer all servicing to qualified service
personnel. Servicing is required when the
unit has been damaged in any way, such
as power-supply cord or plug is damaged,
liquid has been spilled or objects have
fallen into the apparatus, the unit has
been exposed to rain or moisture,
does not operate normally, or has been
dropped.
Battery usage CAUTION – To prevent
battery leakage which may result in bodily
injury, property damage, or damage to
the remote control:
Install all batteries correctly, + and - as
marked on the remote control.
Do not mix batteries (old and new or
carbon and alkaline, etc.).
Remove batteries when the remote
control is not used for a long time.
The unit shall not be exposed to dripping
or splashing.
Do not place any sources of danger on
the unit (e.g. liquid filled objects, lighted
candles).
•
Where the plug of the Direct Plug-in
Adapter is used as the disconnect device,
the disconnect device shall remain readily
operable.
Know these safety symbols
This ‘bolt of lightning’ indicates uninsulated
material within your unit may cause an electrical
shock. For the safety of everyone in your
household, please do not remove product
covering.
The ‘exclamation point’ calls attention to
features for which you should read the enclosed
literature closely to prevent operating and
maintenance problems.
WARNING: To reduce the risk of fire or electric
shock, this apparatus should not be exposed to
rain or moisture and objects filled with liquids,
such as vases, should not be placed on this
apparatus.
CAUTION: To prevent electric shock, match
wide blade of plug to wide slot, fully insert.
Warning
•• Never remove the casing of this apparatus.
•• Never lubricate any part of this apparatus.
•• Never place this apparatus on other electrical
equipment.
•• Keep this apparatus away from direct sunlight,
naked flames or heat.
•• Never look into the laser beam inside this
apparatus.
•• Ensure that you always have easy access to the
power cord, plug or adaptor to disconnect this
apparatus from the power.
EN
DCM2060_93_UM_V1.1.indb 4
2011/8/31 15:18:42
English
Hearing Safety
Danger
•• To avoid hearing damage, limit the time you use the
headphones at high volume and set the volume to a
safe level. The louder the volume, the shorter is the safe
listening time.
Be sure to observe the following guidelines
when using your headphones.
• Listen at reasonable volumes for
reasonable periods of time.
• Be careful not to adjust the volume
continuously upwards as your hearing
adapts.
• Do not turn up the volume so high that
you can’t hear what’s around you.
• You should use caution or temporarily
discontinue use in potentially hazardous
situations.
• Excessive sound pressure from earphones
and headphones can cause hearing loss.
Caution
•• Use of controls or adjustments or
performance of procedures other than herein
may result in hazardous radiation exposure or
other unsafe operation.
EN
DCM2060_93_UM_V1.1.indb 5
5
2011/8/31 15:18:42
2 Your Micro
System
Congratulations on your purchase, and
welcome to Philips! To fully benefit from the
support that Philips offers, register your product
at www.philips.com/welcome.
Introduction
With this unit, you can:
• enjoy audio from discs, iPod/iPhone/iPad,
USB devices, and other external devices
• listen to FM radio
You can enrich sound output with these sound
effects:
• Digital Sound Control (DSC)
• Dynamic Bass Boost (DBB)
What’s in the box
Check and identify the contents of your
package:
• Main unit
• Remote control
• Power adapter
• 1 x MP3 link cable
• Mounting kit (2 dowels and 2 screws)
• FM antenna
• Rubber pad for iPad
• User manual
• Quick start guide
• Wall mounting instructions
If you contact Philips, you will be asked for the
model and serial number of this apparatus. The
model number and serial number are on the
bottom of the apparatus. Write the numbers
here:
Model No. __________________________
Serial No. ___________________________
The unit supports these media formats:
6
EN
DCM2060_93_UM_V1.1.indb 6
2011/8/31 15:18:43
English
Overview of the main unit
a
b
g
MP3-LINK
c
d
h
i
e
j
SOURCE
OK /
MENU /
VOLUME
VOLUME
f
m
n
k
l
a
b
c
FM ANT
MICRO MUSIC SYSTEM DCM2060
DOC K for
•
Connect USB device.
•
Headphone socket.
•
•
Turn the unit on/off.
Switch to standby mode.
dSOURCE
• Select a source: CD, FM, USB, Dock,
or MP3 LINK.
e
o
DC IN
12 V
3A
•
•
•
•
/
Skip to the previous/next track.
Search within a track/disc.
Tune to radio stations.
Adjust time.
fOK/
• Confirm selection.
• Switch between mono and stereo
broadcast.
• Start/pause play.
gMP3-LINK
• Connect an external audio device.
h
•
Open/close the disk tray.
i VOLUME + / • Adjust volume.
jMENU/
• Access iPod/iPhone/iPad menu.
• Stop play or erase a program.
k FM ANT
• Improve FM reception.
EN
DCM2060_93_UM_V1.1.indb 7
7
2011/8/31 15:18:45
l DC IN
• Connect power.
m Display panel
• Show play information.
Overview of the remote
control
n Disc tray
o DOCK for iPod/iPhone/iPad
a
b
c
CD
FM
PRESET/ALBUM
s
r
q
OK
d
MP 3 LINK
e
DOCK
USB
MENU
DISPLAY
f
p
o
RDS
g
h
VOL
1
2
3
4
5
6
7
8
9
j
PROG/
CLOCK SET
0
REPEAT/
SHUFFLE
n
k
SLEEP/
TIMER
DSC
DBB
m
i
l
a
b
8
•
•
Turn the unit on/off.
Switch to standby mode.
•
Mute/restore sound.
EN
DCM2060_93_UM_V1.1.indb 8
2011/8/31 15:18:45
d
•
•
•
•
/
Skip to the previous/next track.
Search within a track/disc.
Tune to radio stations.
Adjust time.
e USB/MP3 LINK
• Select USB/MP3 link source.
fRDS/DISPLAY
• Show time and play information.
• Have no RDS function.
g
•
pDOCK
• Select iPod/iPhone/iPad source.
English
c CD
• Select CD source.
qOK
• Confirm selection.
• Switch between mono and stereo
broadcast.
r
•
•
/
Select a preset radio station.
Skip to previous/next album.
sFM
• Select FM tuner source.
Start/pause play.
h VOL +/• Adjust volume.
i Numeric Keypad 0 - 9
• Select a track from a disc or USB
device directly.
• Select a preset radio station.
j PROG/CLOCK SET
• Program tracks.
• Program radio stations.
• Set time.
kSLEEP/TIMER
• Set sleep/alarm timer.
lDSC
• Select a preset sound setting.
mDBB
• Turn dynamic bass enhancement on/
off.
nREPEAT/SHUFFLE
• Play a track or all tracks repeatedly.
• Play tracks in current album
repeatedly.
• Play tracks randomly.
oMENU/
• Access iPod/iPhone/iPad menu.
• Stop play or erase a program.
EN
DCM2060_93_UM_V1.1.indb 9
9
2011/8/31 15:18:46
3 Get started
Caution
•• Use of controls or adjustments or
performance of procedures other than herein
may result in hazardous radiation exposure or
other unsafe operation.
Always follow the instructions in this chapter in
sequence.
Prepare the remote control
Caution
•• Risk of explosion! Keep batteries away from
heat, sunshine or fire. Never discard batteries
in fire.
•• Risk of decreased battery life! Never mix
different brands or types of batteries.
•• Risk of product damage! When the remote
control is not used for long periods, remove
the batteries.
To install the remote control battery:
Placement
You can place the unit on a flat surface or
mount the unit on a wall.
Mount on a wall
1
2
3
Open the battery compartment.
Insert 2 AAA batteries with correct
polarity (+/-) as indicated.
Close the battery compartment.
a
See the wall mounting instructions included in
the package.
Connect FM antenna
b
Tip
•• For optimal reception, fully extend and adjust
the position of the antenna.
Connect the supplied FM antenna to the FM
ANT socket on the main unit.
10
c
EN
DCM2060_93_UM_V1.1.indb 10
2011/8/31 15:18:46
Caution
•• Risk of product damage! Ensure that the
power supply voltage corresponds to the
voltage printed on the back or the underside
of the unit.
•• Risk of electric shock! When you unplug the
power cord, always pull the plug from the
socket. Never pull the cord.
•• Before connecting the power adapter, ensure
that you have completed all other connections.
2
3
4
5
Press CLOCK SET again.
»» The 12 or 24 hour format blinks.
English
Connect power
Press
/
repeatedly to select an
hour format.
Press CLOCK SET to confirm.
»» The hour digits blink.
Repeat steps 3-4 to set the hour and
minute respectively.
Note
•• If no button is pressed in 90 seconds, the unit
exits clock setting mode automatically.
Note
•• The type plate is located at the back of the
main unit.
Connect the power adapter to:
• the DC IN socket on the main unit.
• the wall socket.
Turn on
Press .
»» The unit switches to the last selected
source.
Note
•• To select a source, press SOURCE repeatedly
or the source selection buttons on the remote
control.
Switch to standby mode
Press again to switch the unit to standby
mode.
»» The clock (if set) appears on the display
panel.
Set clock
1
In standby mode, press and hold CLOCK
SET on the remote control for two
seconds.
»» [SET CLOCK] (set clock) scrolls on
the display.
EN
DCM2060_93_UM_V1.1.indb 11
11
2011/8/31 15:18:47
4Play
Play from iPod/iPhone/iPad
Play disc
You can enjoy audio from iPod/iPhone/iPad
through this unit.
1
2
3
4
Press
to open the disc compartment.
Insert a disc with the printed side facing
up.
Press
to close the disc compartment.
Press CD on the remote control to select
the disc source.
»» [Reading] (reading) blinks for a
moment, then CD starts playing
automatically. If not, press
.
Play from USB
Note
•• Make sure that the USB device contains
Compatible iPod/iPhone/iPad
The unit supports the following iPod, iPhone
and iPad models:
Made for.
• iPod touch (1st, 2nd, 3rd, and 4th
generation)
• iPod nano (2nd, 3rd, 4th, 5th, and 6th
generation)
• iPhone 4
• iPhone 3GS
• iPhone 3G
• iPhone
• iPad 2
• iPad
Load the iPod/iPhone/iPad
playable audio content.
1
Insert the USB device into the
socket.
1
2
2
12
Press USB on the remote control to
select the USB source.
»» Play starts automatically. If not, press
.
Push the dock compartment to open it.
Place the iPod/iPhone/iPad in the dock.
Install the rubber pad
If necessary, install the supplied rubber pad to
keep the iPad/iPad 2 stable before you place
the iPad/iPad 2.
EN
DCM2060_93_UM_V1.1.indb 12
2011/8/31 15:18:47
English
Play options
Pause/resume play
During play, press
Listen to the iPod/iPhone/iPad
1
2
3
Make sure that the iPod/iPhone/iPad is
loaded correctly.
Repeat/shuffle play
1
Press SOURCE repeatedly or DOCK on
the remote control to select iPod/iPhone/
iPad source.
Play tracks in the iPod/iPhone/iPad.
• To pause/resume play, press
.
• To skip to a track, press
/ .
• To search during play, press and hold
/ , then release to resume
normal play.
• To go back to the previous iPod/
iPhone/iPad menu, press MENU.
• To scroll through the menu, press
/ .
• To confirm a selection, press OK.
Remove the iPod/iPhone/iPad
Pull the iPod/iPhone/iPad out of the dock.
Charge the iPod/iPhone/iPad
2
with video are not compatible with dock
charging.
When the unit is connected to power, the
docked iPod/iPhone/iPad begins to charge.
During play, press REPEAT/SHUFFLE
repeatedly to select:
•
: play the current track repeatedly.
•
(for MP3/WMA only): play all
tracks in this album repeatedly.
•
: play all tracks repeatedly.
•
: play all tracks randomly.
To resume normal play, press
REPEAT/SHUFFLE repeatedly until the
above icons disappear.
Skip to a track
For CD:
Press
/
to select another track.
For MP3 disc and USB:
1
2
Press /
folder.
Press
to select an album or a
/
to select a track/file.
Tip
•• To select a track directly, you can also press a
key on the numerical keypad.
Note
•• iPod with color display, iPod classic, and iPod
to pause/resume play.
Search within a track
1
2
During play, press and hold
/
.
Release to resume normal play.
Tip
•• For certain iPod models, it may take up to a
minute before the charging indication appears.
EN
DCM2060_93_UM_V1.1.indb 13
13
2011/8/31 15:18:48
Program tracks
You can program a maximum of 20 tracks.
1
2
3
4
5
In CD/USB mode, press to stop
playback, then press PROG to activate
the programming mode.
»» [PROG] (program) is displayed.
For MP3/WMA tracks, press
select an album.
/
to
Press
/
to select a track, then
press PROG to confirm.
Repeat steps 2 to 3 to program more
tracks.
Press
to play the programmed tracks.
»» During play, [PROG] (program) is
displayed.
•
To erase the program, when
playback is stopped, press .
Adjust sound
5 Listen to FM
radio
Auto install FM radio stations
When the unit turns to FM tuner mode, and
no radio stations are stored, the unit begins to
store FM radio stations automatically.
Note
•• Position the antenna as far as possible from
TV, VCR, or other radiation source.
•• Ensure that you have connected and fully
extended the supplied FM antenna.
1
2
During play, you can adjust volume and select
sound effects.
Function
To increase/decrease volume
To mute/restore sound
To turn dynamic bass
enhancement on/off
To select a sound effect:
[POP] (pop)
[JAZZ] (jazz)
[CLASSIC] (classic)
[ROCK] (rock)
[FLAT] (flat)
Action
Press VOL
+/-.
Press .
Press DBB.
Press and hold
for 3 seconds to start
full scan.
»» The unit automatically stores FM radio
stations with sufficient signal strength
and then broadcasts the first preset
station.
Tip
•• To exit storing mode, press or .
•• RDS service is not available.
Press DSC
repeatedly.
Display different information
During play, press DISPLAY repeatedly to view
time and different play information.
14
Press FM to select FM tuner mode.
»» [AUTO INSTALL - PRESS PLAY, STOP
CANCEL] (to auto install, press
;
to cancel, press ) is displayed.
Tune to FM radio stations
1
2
In FM tuner mode, press and hold
for 3 seconds.
»» [SEARCH] (search) is displayed.
/
»» The unit tunes to an FM station with
strong reception automatically.
Repeat step 1 to tune to more stations.
EN
DCM2060_93_UM_V1.1.indb 14
2011/8/31 15:18:49
Program FM radio stations
automatically
Note
•• You can program a maximum of 20 preset FM
radio stations.
In FM tuner mode, press and hold PROG for 3
seconds.
»» [AUTO] (auto) is displayed.
»» The unit stores all the FM radio stations
automatically and then broadcasts the first
preset radio station.
Select a preset radio station
English
To tune to a weak station:
Press
/
repeatedly until you find optimal
reception.
In tuner mode, press / or the numeric
buttons to select a preset number.
Select stereo/mono broadcast
Note
•• Stereo broadcast is the default setting for
tuner mode.
•• For stations with weak signals: to improve the
reception, change to monaural sound.
In FM tuner mode, press OK to switch between
mono and stereo broadcast.
Program FM radio stations
manually
1
2
3
4
5
In tuner mode, tune to an FM radio
station.
Press PROG to activate programming
mode.
»» [PROG] (program) blinks.
Press / repeatedly to select a
channel number.
Press PROG again to confirm.
Repeat steps 1-4 to store other FM
stations.
Note
•• To remove a pre-stored station, store another
station in its place.
EN
DCM2060_93_UM_V1.1.indb 15
15
2011/8/31 15:18:49
6 Other features
Tip
•• If CD/USB/iPod source is selected, but no
disc is inserted or no USB/ipod/iPhone/iPad
connected, the unit switches to the tuner
source automatically.
Set the alarm timer
This unit can be used as an alarm timer. You can
select CD, FM tuner, iPod/iPhone/iPad, or USB
as alarm source.
Set the sleep timer
Note
Note
•• Make sure that you have set the clock
correctly.
1
2
3
4
5
6
•• Make sure that you have set the clock
In standby mode, press and hold TIMER
until [SET TIMER] (set timer) scrolls on
the display.
»» [SELECT SOURCE] (select source) is
displayed.
Press SOURCE repeatedly or the source
selection buttons on the remote control
to select a source: disc, FM tuner, iPod/
iPhone/iPad, or USB.
correctly.
When the unit is turned on, press SLEEP
repeatedly to select the sleep timer period (in
minutes).
»» When sleep timer is activated, is
displayed.
Tip
•• To deactivate the sleep timer, press SLEEP
repeatedly until [OFF] (off ) is displayed.
Press TIMER to confirm.
»» The hour digits blink.
Press
/
repeatedly to set the hour.
Press TIMER to confirm.
»» The minute digits blink.
Repeat steps 4-5 to set the minute and
alarm volume.
Note
•• If no button is pressed in 90 seconds, the unit
exits alarm setting mode automatically.
To activate or deactivate the alarm timer,
In standby mode, press TIMER repeatedly to
activate or deactivate the alarm.
»» appears when the timer is activated.
Listen through the headphone
Plug a headphone into the
Play from external audio
device
With this unit, you can play audio from an
external audio device like MP3 player.
1
2
3
16
socket on the unit.
Connect the supplied MP3 Link cable to
• the MP3-LINK socket.
• the audio output socket of an
external device.
Press USB/MP3 LINK repeatedly to
select MP3 link mode.
Start to play the external device (see the
device’s user manual).
EN
DCM2060_93_UM_V1.1.indb 16
2011/8/31 15:18:50
Note
without prior notice.
Specifications
Amplifier
2 X 10 W RMS
80 Hz - 16 kHz, ± 3 dB
≥60 dB
0.5 V RMS 20 kohm
Disc
Laser Type
Disc Diameter
Support Disc
>28 dBf
<3%
>50 dB
20
General information
•• Product information is subject to change
Rated Output
Power
Frequency
Response
Signal to Noise
Ratio
MP3 Link Input
Search selectivity
Total harmonic distortion
Signal to noise ratio
Number of presets
English
7Product
information
Semiconductor
12 cm/8 cm
CD-DA, CD-R,
CD-RW, MP3-CD,
WMA-CD
24 Bits/44.1 kHz
<1.5 % (1 kHz)
Audio DAC
Total Harmonic
Distortion
Frequency Response 60 Hz - 16 kHz
S/N Ratio
>55 dBA
Tuner (FM)
Tuning range
Tuning grid
Sensitivity
- Mono, 26dB S/N Ratio
- Stereo, 46dB S/N Ratio
87.5 - 108 MHz
50 KHz
<22 dBf
>43 dBf
AC power
Operation Power
Consumption
Standby Power
Consumption
Dimensions
- Main Unit
(W x H x D)
Weight
- With Packing
- Main Unit
Model: AS360-120AB300;
Input: 100 - 240 V ~,
50/60 Hz, 1.2 A;
Output: 12 V 3.0 A
25 W
≤1 W
400 x 235 x 97.5 mm
3.7 kg
2.2 kg
USB playability information
Compatible USB devices:
• USB flash memory (USB1.1)
• USB flash players (USB1.1)
• memory cards (requires an additional
card reader to work with this unit)
Supported formats:
• USB or memory file format: FAT12,
FAT16, FAT32 (sector size: 512 bytes)
• MP3 bit rate (data rate): 32-320 Kbps and
variable bit rate
• WMA v9 or earlier
• Directory nesting up to a maximum of 8
levels
• Number of albums/ folders: maximum 99
• Number of tracks/titles: maximum 999
• ID3 tag v2.0 or later
EN
DCM2060_93_UM_V1.1.indb 17
17
2011/8/31 15:18:50
•
File name in Unicode UTF8 (maximum
length: 16 bytes)
Unsupported formats:
• Empty albums: an empty album is an
album that does not contain MP3/WMA
files, and is not be shown in the display.
• Unsupported file formats are skipped. For
example, Word documents (.doc) or MP3
files with extension .dlf are ignored and
not played.
• AAC, WAV, PCM audio files
• DRM protected WMA files (.wav, .m4a,
.m4p, .mp4, .aac)
• WMA files in Lossless format
Supported MP3 disc formats
•
•
•
•
•
18
ISO9660, Joliet
Maximum title number: 999 (depending
on file name length)
Maximum album number: 99
Supported sampling frequencies: 32 kHz,
44.1 kHz, 48 kHz
Supported Bit-rates: 32~320 (kbps),
variable bit rates
EN
DCM2060_93_UM_V1.1.indb 18
2011/8/31 15:18:50
Warning
•• Never remove the casing of this apparatus.
To keep the warranty valid, never try to repair
the system yourself.
If you encounter problems when using this
apparatus, check the following points before
requesting service. If the problem remains
unsolved, go to the Philips web site (www.
philips.com/welcome). When you contact
Philips, ensure that the apparatus is nearby
and the model number and serial number are
available.
No power
•• Ensure that the AC power cord of the
unit is connected properly.
•• Ensure that there is power at the AC
outlet.
•• As a power-saving feature, the system
switches off automatically 15 minutes
after track play reaches the end and no
control is operated.
No sound or poor sound
•• Adjust the volume.
•• Disconnect the headphones.
•• Check that the speakers are connected
correctly.
•• Check if the stripped speaker wires are
clamped.
No response from the unit
•• Disconnect and reconnect the AC power
plug, then turn on the unit again.
•• As a power-saving feature, the system
switches off automatically 15 minutes
after track play reaches the end and no
control is operated.
Remote control does not work
•• Before you press any function button,
first select the correct source with the
remote control instead of the main unit.
•• Reduce the distance between the remote
control and the unit.
•• Insert the battery with its polarities (+/–
signs) aligned as indicated.
•• Replace the battery.
•• Aim the remote control directly at the
sensor on the front of the unit.
No disc detected
•• Insert a disc.
•• Check if the disc is inserted upside down.
•• Wait until the moisture condensation at
the lens has cleared.
•• Replace or clean the disc.
•• Use a finalized CD or correct format disc.
Cannot display some files in USB device
•• The number of folders or files in the USB
device has exceeded a certain limit. This
phenomenon is not a malfunction.
•• The formats of these files are not
supported.
USB device not supported
•• The USB device is incompatible with the
unit. Try another one.
Poor radio reception
•• Increase the distance between the unit
and your TV or VCR.
•• Fully extend the FM antenna.
Timer does not work
•• Set the clock correctly.
•• Switch on the timer.
Clock/timer setting erased
•• Power has been interrupted or the power
cord has been disconnected.
•• Reset the clock/timer.
EN
DCM2060_93_UM_V1.1.indb 19
English
8Troubleshooting
19
2011/8/31 15:18:50
9Notice
Any changes or modifications made to this
device that are not expressly approved by
Philips Consumer Lifestyle may void the user’s
authority to operate the equipment.
Disposal of your old product and
batteries
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
Never dispose of your product with other
household waste. Please inform yourself about
the local rules on the separate collection
of electrical and electronic products and
batteries. The correct disposal of these
products helps prevent potentially negative
consequences on the environment and human
health.
Please visit www.recycle.philips.com for
additional information on a recycling center in
your area.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and
old equipment.
20
“Made for iPod,” “Made for iPhone,” and
“Made for iPad” mean that an electronic
accessory has been designed to connect
specifically to iPod, iPhone, or iPad,
respectively, and has been certified by the
developer to meet Apple performance
standards. Apple is not responsible for the
operation of this device or its compliance
with safety and regulatory standards. Please
note that the use of this accessory with
iPod, iPhone, or iPad may affect wireless
performance.
iPod and iPhone are trademarks of Apple Inc.,
registered in the U.S. and other countries. iPad
is a trademark of Apple Inc.
The making of unauthorized copies of copyprotected material, including computer
programs, files, broadcasts and sound
recordings, may be an infringement of
copyrights and constitute a criminal offence.
This equipment should not be used for such
purposes.
This apparatus includes this label:
EN
DCM2060_93_UM_V1.1.indb 20
2011/8/31 15:18:51
部件名称
Name of the
Parts
有毒有害物质或元素
Hazardous/toxic Substance
铅
(Pb, Lead)
汞 (Hg,
Mercury)
镉 (Cd,
cadmium)
六价铬(Chromium
6+)
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
Housing
外壳
O
O
O
O
O
O
DVD/CD loader
DVD/CD 光盒
X
O
O
O
O
O
LCD Panel
液晶面板
X
X
O
O
O
O
Loudspeakers
喇叭单元
O
O
O
O
O
O
PWBs
电路板组件
X
O
O
O
O
O
Accessories
(Remote control &
cables)
附件（遥控器，电
源线，连接线）
X
O
O
O
O
O
Batteries in
Remote Control
(ZnC)
遥控器电池
X
O
O
O
O
O
○：表示该有毒有害物质在该部件所有均质材料中的含量均在SJ/T11363 - 2006 标准规定的限量要求以下。
O:Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this
part is below the limit requirement in SJ/T11363 － 2006.
×：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出SJ/T11363 － 2006 标准规定的限量要
求。
X:Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials
used for this part is above the limit requirement in SJ/T11363 - 2006.
环保使用期限 Environmental Protection Use Period
This logo refers to the period ( 10 years )
电子信息产品中含有的有毒有害物质或元素在正常使用的条件下不会发生外泄或突变，电子信息产品用户使
用该电子信息产品不会对环境造成严重污染或对其人身、财产造成严重 损害的期限。
This logo refers to the period ( 10 years ) during which the toxic or hazardous substances or elements
contained in electronic information products will not leak or mutate so that the use of these [substances or
elements] will not result in any severe environmental pollution, any bodily injury or damage to any assets.
DCM2060_93_UM_V1.1.indb 39
2011/8/31 15:19:02
© 2011 Koninklijke Philips Electronics N.V.
All rights reserved.
DCM2060_93_UM_V1.1
DCM2060_93_UM_V1.1.indb 40
2011/8/31 15:19:02