Register your product and get support at
DCM377
www.philips.com/welcome
EN
User manual
DCM377_05_UM_V1.1.indd
1
2010-9-29
16:46:45
1
Important
Safety
Notice
4
4
5
2
Your Docking Entertainment System
Introduction
What’s in the box
Overview of the main unit
Overview of the remote control
6
6
6
7
8
3
Get started
Connect speakers
Connect FM antenna
Connect power
Prepare the remote control
Set clock
Turn on
Store radio stations automatically
9
9
9
9
10
10
10
10
4
Play
Basic play operations
Play from disc
Play from USB
Adjust sound
11
11
11
11
11
5
Play iPhone/iPod
Compatible iPhone/iPod
Listen to the iPhone/iPod
Charge the iPhone/iPod
Remove the iPhone/iPod
12
12
12
12
12
6
Listen to FM radio
Tune to FM radio stations
Program radio stations automatically
Program radio stations manually
Tune to a preset radio station
Show RDS information
13
13
13
13
13
13
7
Other features
Set alarm timer
Set sleep timer
Listen to external audio device
Listen through headphone
14
14
14
14
14
8
Product information
6SHFLÀFDWLRQV
USB playability information
Supported MP3 disc formats
14
14
15
15
9
Troubleshooting
16
EN
DCM377_05_UM_V1.1.indd
3
2010-9-29
English
Contents
3
16:46:45
1 Important
Safety
This ‘bolt of lightning’ indicates uninsulated material
within your unit may cause an electrical shock. For
the safety of everyone in your household, please do
not remove product covering.
The ‘exclamation point’ calls attention to features
for which you should read the enclosed literature
closely to prevent operating and maintenance
problems.
:$51,1*7RUHGXFHWKHULVNRIÀUHRUHOHFWULF
shock, this apparatus should not be exposed to rain
RUPRLVWXUHDQGREMHFWVÀOOHGZLWKOLTXLGVVXFKDV
vases, should not be placed on this apparatus.
CAUTION: To prevent electric shock, match wide
blade of plug to wide slot, fully insert.
Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Do not install near any heat sources such
as radiators, heat registers, stoves, or other
DSSDUDWXVLQFOXGLQJDPSOLÀHUVWKDWSURGXFH
heat.
Protect the power cord from being walked on
or pinched, particularly at plugs, convenience
receptacles, and the point where they exit
from the apparatus.
2QO\XVHDWWDFKPHQWVDFFHVVRULHVVSHFLÀHGE\
the manufacturer.
Use only with the cart, stand,
tripod, bracket, or table
VSHFLÀHGE\WKHPDQXIDFWXUHU
or sold with the apparatus.
When a cart is used, use
caution when moving the cart/
apparatus combination to avoid
injury from tip-over.
Unplug this apparatus during lightning storms
or when unused for long periods of time.
4
Refer DOOVHUYLFLQJWRTXDOLÀHGVHUYLFH
personnel. Servicing is required when the
apparatus has been damaged in any way, such
as power-supply cord or plug is damaged,
liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate
normally, or has been dropped.
Battery usage CAUTION – To prevent battery
leakage which may result in bodily injury,
property damage, or damage to the unit:
Install all batteries correctly, + and - as marked
on the unit.
Do not mix batteries (old and new or carbon
and alkaline, etc.).
Remove batteries when the unit is not used
for a long time.
Apparatus shall not be exposed to dripping or
splashing.
Do not place any sources of danger on the
DSSDUDWXVHJOLTXLGÀOOHGREMHFWVOLJKWHG
candles).
Important notes for users in the U.K.
How to connect a plug
The wires in the mains lead are coloured with the
following code: blue = neutral (N), brown = live (L).
As these colours may not correspond with the
colour markings identifying the terminals in your
plug, proceed as follows:
Connect the blue wire to the terminal marked
N or coloured black.
Connect the brown wire to the terminal
marked L or coloured red.
Do not connect either wire to the earth
terminal in the plug, marked E (or e) or
coloured green (or green and yellow).
Before replacing the plug cover, make certain
that the cord grip is clamped over the sheath
of the lead - not simply over the two wires.
Mains plug
7KLVDSSDUDWXVLVÀWWHGZLWKDQDSSURYHG$PS
plug. To change a fuse in this type of plug proceed
as follows:
Remove fuse cover and fuse.
Fix new fuse which should be a BS1362 3 Amp,
A.S.T.A. or BSI approved type.
ReÀWWKHIXVHFRYHU
,IWKHÀWWHGSOXJLVQRWVXLWDEOHIRU\RXUVRFNHW
outlets, it should be cut off and an appropriate plug
ÀWWHGLQLWVSODFH
If the mains plug contains a fuse, this should have a
value of 3 Amp. If a plug without a fuse is used, the
fuse at the distribution board should not be greater
than 3 Amp.
EN
DCM377_05_UM_V1.1.indd
4
2010-9-29
16:46:46
Copyright in the U.K.
Recording and playback of material may require
consent. See Copyright Act 1956 and The
Performer’s Protection Acts 1958 to 1972.
Caution
Use of controls or adjustments or performance of
$Q\FKDQJHVRUPRGLÀFDWLRQVPDGHWRWKLV
device that are not expressly approved by Philips
Consumer Lifestyle may void the user’s authority to
operate the equipment.
English
The severed plug must be disposed off to avoid a
possible shock hazard should it be inserted into a 13
Amp socket elsewhere.
Your product is designed and manufactured with
high quality materials and components, which can
be recycled and reused.
procedures other than herein may result in hazardous
radiation exposure or other unsafe operation.
Warning
Where the MAINS plug or an appliance coupler is used
as the disconnect device, the disconnect device shall
remain readily operable.
Hearing Safety
Danger
To avoid hearing damage, limit the time you use the
headphones at high volume and set the volume to a
safe level. The louder the volume, the shorter is the safe
listening time.
Be sure to observe the following guidelines when
using your headphones.
Listen at reasonable volumes for reasonable
periods of time.
Be careful not to adjust the volume
continuously upwards as your hearing adapts.
Do not turn up the volume so high that you
can’t hear what’s around you.
You should use caution or temporarily
discontinue use in potentially hazardous
situations.
Excessive sound pressure from earphones and
headphones can cause hearing loss.
Notice
This product complies with the radio interference
requirements of the European Community.
This product complies with the requirements of the
following directives and guidelines: 2004/108/EC +
2006/95/EC
When this crossed-out wheeled bin symbol is
attached to a product it means that the product is
covered by the European Directive 2002/96/EC.
Please inform yourself about the local separate
collection system for electrical and electronic
products.
Please act according to your local rules and do not
dispose of your old products with your normal
household waste. Correct disposal of your old
product helps to prevent potential negative
consequences for the environment and human
health.
Your product contains batteries covered by the
European Directive 2006/66/EC, which cannot
be disposed with normal household waste.Please
inform yourself about the local rules on separate
collection of batteries because correct disposal
helps to prevent negative consequences for the
environmental and human health.
Environmental information
All unnecessary packaging has been omitted. We
have tried to make the packaging easy to separate
into three materials: cardboard (box), polystyrene
foam (buffer) and polyethylene (bags, protective
foam sheet.)
Your system consists of materials which can be
recycled and reused if disassembled by a specialized
company. Please observe the local regulations
regarding the disposal of packaging materials,
exhausted batteries and old equipment.
EN
DCM377_05_UM_V1.1.indd
5
2010-9-29
5
16:46:46
2 Your Docking
Entertainment System
The making of unauthorized copies of copyprotected material, including computer programs,
ÀOHVEURDGFDVWVDQGVRXQGUHFRUGLQJVPD\EHDQ
infringement of copyrights and constitute a criminal
offence. This equipment should not be used for
such purposes.
“Made for iPod” means that an electronic accessory
KDVEHHQGHVLJQHGWRFRQQHFWVSHFLÀFDOO\WRL3RG
DQGKDVEHHQFHUWLÀHGE\WKHGHYHORSHUWRPHHW
Apple performance standards.
“Works with iPhone” means that an electronic
DFFHVVRU\KDVEHHQGHVLJQHGWRFRQQHFWVSHFLÀFDOO\
WRL3KRQHDQGKDVEHHQFHUWLÀHGE\WKHGHYHORSHU
to meet Apple performance standards.
Apple is not responsible for the operation of this
device or its compliance with safety and regulatory
standards.
iPod is a trademark of Apple Inc., registered in the
U.S. and other countries.
Congratulations on your purchase, and welcome to
3KLOLSV7RIXOO\EHQHÀWIURPWKHVXSSRUWWKDW3KLOLSV
offers, register your product at www.philips.com/
welcome.
Introduction
With this unit, you can:
enjoy audio from discs, USB devices, iPod,
iPhone and other external devices
listen to radio stations
You can enrich sound output with these sound
effects:
Digital Sound Control (DSC)
Dynamic Bass Boost (DBB)
Loudness Control
The unit supports these media formats:
Norge
7\SHVNLOWÀQQHVSnDSSDUDWHQVXQGHUVLGH
Observer: Nettbryteren er sekundert innkoplet.
Den innebygde netdelen er derfor ikke frakoplet
QHWWHWVnOHQJHDSSDUDWHWHUWLOVOXWWHWQHWWNRQWDNWHQ
)RUnUHGXVHUHIDUHQIRUEUDQQHOOHUHOHNWULVNVW¡W
skal apparatet ikke utsettes for regn eller fuktighet.
This apparatus includes this label:
What’s in the box
Note
The type plate is located on the bottom of the apparatus.
6
Check and identify the contents of your package:
Main unit
Remote control with battery
Speaker boxes (×2)
FM antenna
Power cable
MP3 link cable (60cm)
User manual
EN
DCM377_05_UM_V1.1.indd
6
2010-9-29
16:46:47
English
Overview of the main unit
p
o
n
m
l
k
a
j
i
h
b
c
g
f
d
e
a VOLUME
Adjust volume.
b DSC
Select a preset sound setting.
c DBB
Turn on or off dynamic bass
enhancement.
d
USB socket.
h OPEN/CLOSE
Open or close the disc tray.
i SOURCE
Select a source.
j ALBUM/PRESET /
Skip to previous/next album.
Select a preset radio station.
Navigate through iPod/iPhone menu.
k
e MP3 LINK
Connect external audio device.
f
Headphone socket.
g Disc tray
/
Skip to previous/next track.
Search within a track/disc.
Tune to a radio station.
Stop play.
Erase a program.
l
EN
DCM377_05_UM_V1.1.indd
7
2010-9-29
7
16:46:49
m
a
Start or pause play.
n Display panel
Show current status.
o
Turn on the apparatus, switch to standby
mode, or Eco Power standby mode.
p Dock for iPhone / iPod
Turn on the unit.
Switch to standby or Eco Power standby
mode.
b Source selection keys (CD, USB, FM, iPhone,
iPod, AUX, MP3 LINK)
Select a source.
c RDS
For selected FM radio stations: display
RDS information.
Synchronize clock with RDS station.
Overview of the remote control
d DISPLAY
Display play information.
a
CD
USB
FM
MP 3 LINK
REPEAT
SHUFFLE
b
DISPLAY
d
e
ALBUM/PRESET
u
f
OK
LOUDNESS
MENU
VOL
g ALBUM/PRESET /
Skip to previous/next album.
Select a preset radio station.
Navigate through iPod/iPhone menu.
h MENU
Access iPod/iPhone menu.
i VOL +/ Adjust volume.
j MUTE
Mute volume.
h
k DIM
Adjust brightness of display panel.
i
DBB
q
1
2
3
MUTE
j
4
5
6
DIM
k
7
8
9
CLOCK
l
PROG
0
SHIFT
TIMER
p
Skip to previous/next track.
Search within a track/disc.
Tune to a radio station.
g
DSC
r
/
c
w
v
SLEEP
o
f
RDS
AUX
OPEN/CLOSE
t
s
e SHUFFLE
Play tracks randomly.
m
n
l CLOCK
Set clock.
m SLEEP/TIMER
Set sleep timer.
Set alarm timer.
n SHIFT
Enter a two or three-digit number (used
with the numeric keypad).
o PROG
Program tracks.
Program radio stations.
p Numeric keypad
Select a track directly.
q
8
Stop play.
Erase a program.
EN
DCM377_05_UM_V1.1.indd
8
2010-9-29
16:46:50
English
r DSC/DBB
Select a preset sound setting.
Turn on or off dynamic bass
enhancement.
s
Start or pause play.
t LOUDNESS
Enable or disable automatic loudness
adjustment.
u OK
&RQÀUPDVHOHFWLRQ
v REPEAT
Select a repeat play mode.
w OPEN/CLOSE
Open or close the disc tray.
Connect FM antenna
3 Get started
Caution
Use of controls or adjustments or performance of
procedures other than herein may result in hazardous
radiation exposure or other unsafe operation.
Always follow the instructions in this chapter in
sequence.
If you contact Philips, you will be asked for the model
and serial number of this apparatus. The model
number and serial number are on the bottom of the
apparatus. Write the numbers here:
Model No. __________________________
Serial No. ___________________________
Connect speakers
Tip
For optimal reception, fully extend and adjust the
position of the antenna.
For better FM stereo reception, connect an outdoor FM
antenna to the FM ANTENNA socket.
The unit does not support MW radio reception.
Note
For optimal sound, use the supplied speakers only.
Connect only speakers with impedance that is the
1
same or higher than the supplied speakers. Refer to the
6SHFLÀFDWLRQVVHFWLRQRIWKLVPDQXDO
1
Connect the supplied FM antenna to the FM
ANTENNA socket on the main unit.
Connect power
Insert the speaker wires completely into the
speaker input sockets on the back of the unit.
Caution
Risk of product damage! Ensure that the power supply
voltage corresponds to the voltage printed on the back
or the underside of the unit.
Risk of electric shock! When you unplug the AC power
cord, always pull the plug from the socket. Never pull
the cord.
Before you connect the AC power cord, ensure that you
have completed all other connections.
EN
DCM377_05_UM_V1.1.indd
9
2010-9-29
9
16:46:51
Note
If you are not going to use the remote control for a long
time, remove the battery.
Set clock
1
Connect the power cable to:
the AC~ jack on the main unit.
the wall socket.
Prepare the remote control
1
In standby mode, press CLOCK for 3 seconds
to activate clock setting mode.
» [SET CLOCK] scrolls on the display, then
the time format [24H] and [12H] appears.
2
Press ALBUM/PRESET to select 24H or 12H,
then press CLOCKWRFRQÀUP
» The hour digits begin to blink.
3
Press ALBUM/PRESET to set hour, then press
CLOCK again.
» The minute digits begin to blink.
4
5
Press ALBUM/PRESET to set minute.
Press CLOCKWRFRQÀUPWKHFORFNVHWWLQJ
Caution
Note
Risk of explosion! Keep batteries away from heat,
VXQVKLQHRUÀUH1HYHUGLVFDUGEDWWHULHVLQÀUH
)RUÀUVWWLPHXVH
1 Remove the protective tab to activate the
remote control battery.
To replace the remote control batteries:
If no button is pressed in 30 seconds, the system exits
clock setting mode automatically.
Turn on
1
Press .
» The unit switches to the last selected
source.
Switch to standby mode
1 Press for over 3 seconds to switch the unit
to Eco Power Standby mode.
» The backlight on the display panel turns off.
» The blue Eco Power indicator turns on.
To switch the unit to standby mode:
In Eco Power Standby mode, press for over
3 seconds.
» The clock (if set) appears on the display
panel.
» The blue Eco Power indicator turns off.
1
1
2
3
Open the battery compartment.
Insert one lithium CR2025 battery with
correct polarity (+/-) as indicated.
Close the battery compartment.
10
EN
DCM377_05_UM_V1.1.indd
10
Store radio stations automatically
When the unit is connected to power and no radio
stations are stored, the unit begins to store radio
stations automatically.
1 Connect the unit to power supply.
» [AUTO INSTALL PRESS--PLAY KEY](auto
install press - play key) is displayed.
2010-9-29
16:46:51
Press
to start storing.
» The unit automatically stores radio stations
ZLWKVXIÀFLHQWVLJQDOVWUHQJWK
» When all the available radio stations are
VWRUHGWKHÀUVWSUHVHWUDGLRVWDWLRQLV
broadcast automatically.
Play from USB
English
2
4 Play
Basic play operations
You can control play through following operations.
Key
/
DISPLAY
REPEAT
SHUFFLE
Function
7RVHOHFWDWUDFNRUÀOH
Press and hold to fast-forward/fastreverse the track during playback,
then release to resume play.
To pause/resume play during
playback.
To select different play information.
To select a repeat play mode:
[REP] (repeat): play current track
repeatedly.
[REP ALL] (repeat all): play all tracks
repeatedly.
[REP] (repeat) and [ALB] (album) (for
MP3 and USB only): play the current
album repeatedly.
Press again to return to normal play.
To play tracks randomly.
Press again to return to normal play.
Play from disc
1
2
Press CD to select the CD source.
Press OPEN/CLOSE.
» The disc compartment opens.
3
Place a disc with the printed side facing up,
then press OPEN/CLOSE.
Play starts automatically.
If play does not start, press
/
to select a
track, then press
.
4
Warning
Ensure that the USB device contains playable audio
contents for supported formats.
1
2
3
Flip open the cover marked
on the front
panel.
Insert the USB device into the USB socket.
Press USB to select the USB source.
» Play starts automatically. If not, press
ALBUM/PRESET to select a folder and
/ WRVHOHFWDÀOH7KHQSUHVVOK to start
play.
Adjust sound
During play, you can adjust volume through following
operations.
Key
VOL +/MUTE
LOUDNESS
DBB
DSC
Function
To increase/decrease the volume.
To mute/restore sound.
To turn on/off automatic loudness
control.
To turn on or off dynamic bass
enhancement.
If DBB is activated, [DBB] is
displayed.
To select your desired sound effect:
[POP] (pop)
[JAZZ] (jazz)
[ROCK] (rock)
[FLAT]ÁDW
[CLASSIC] (classic)
EN
DCM377_05_UM_V1.1.indd
11
11
2010-9-29
16:46:52
5 Play iPhone/iPod
You can enjoy audio from iPhone/iPod through this
unit.
Compatible iPhone/iPod
The unit supports the following iPod and iPhone
models:
Made for.
iPod classic
iPod with color display
iPod with video
iPod nano (1st/2nd/3rd/4th/5th generation)
iPod Touch (1st/2nd/3rd generation)
Works with.
iPhone
iPhone 3G
iPhone 3GS
Listen to the iPhone/iPod
1
2
Press iPhone/iPod to select the iPhone/iPod
source.
Open the iPhone/iPod dock on the top panel.
To pause/resume play, press
.
To skip to a track, press
/ .
To search during play: press and hold
/ , then release to resume normal play.
To navigate the menu: press MENU and
/ to select, then press OKWRFRQÀUP
Note
When iPod/iPhone source is selected, you cannot enjoy
audio through the headphone socket.
Charge the iPhone/iPod
When the unit is connected to power, the docked
iPhone/iPod begins to charge.
Remove the iPhone/iPod
3
Place the iPhone/iPod in the dock.
12
EN
DCM377_05_UM_V1.1.indd
12
1
2
Pull the iPhone/iPod out of the dock.
Press down to hide the dock.
2010-9-29
16:46:53
4
Repeat steps 2-3 to program other stations.
English
6 Listen to FM radio
Note
Tune to FM radio stations
To overwrite a programmed station, store another
station in its place.
Warning
Ensure that you have connected and fully extended the
supplied FM antenna.
1
2
3
Press FM.
Press and hold
/
to tune to a radio
station.
When the frequency starts to change, release
the button.
» The FM tuner tunes to a station with strong
reception automatically.
4
Repeat steps 2-3 to tune to more stations.
To tune to a weak station:
Press
/ UHSHDWHGO\XQWLO\RXÀQGRSWLPDO
reception.
Program radio stations
automatically
Note
1
Press
/
to select a preset number.
Show RDS information
RDS (Radio Data System) is a service that allows FM
stations to show additional information. If you tune to
a RDS station, a RDS icon and the station name are
displayed.
1 Tune to a RDS station.
2 Press RDS repeatedly to scroll through the
following information (if available):
» Station name
» Program type such as [NEWS] (news),
[SPORT] (sport), [POP M] (pop music)...
» RDS clock
» Frequency
Synchronize clock with RDS
You can program a maximum of 20 preset radio stations.
1
Tune to a preset radio station
In FM tuner mode, press PROG for 3 seconds
to activate automatic programming.
» [AUTO] (auto) is displayed.
» The unit automatically stores radio stations
ZLWKVXIÀFLHQWVLJQDOVWUHQJWK
» When all the available radio stations are
VWRUHGWKHÀUVWSUHVHWUDGLRVWDWLRQLV
broadcast automatically.
Program radio stations manually
You can synchronize time shown on the unit with
that on the RDS station.
1 Tune to a RDS radio station that transmits
time signals.
2 Press RDS for over 2 seconds.
» [CT SYNC] is displayed and the unit reads
RDS time automatically.
» If no time signal is received, [NO CT] is
displayed.
Note
The accuracy of the transmitted time depends on the
RDS station that transmits the time signal.
Note
You can program a maximum of 20 preset radio stations.
1
2
3
Tune to a radio station.
Press PROG to activate programming mode.
Press / to select a number from 1–20
for this radio station, then press PROG to
FRQÀUP
» The preset number and the frequency of
the preset station are displayed.
EN
DCM377_05_UM_V1.1.indd
13
13
2010-9-29
16:46:53
7 Other features
Set sleep timer
1
Set alarm timer
This unit can be used as an alarm clock. You can select
CD, iPod/iPhone, iPod/iPhone playlist, FM or USB as
alarm source.
Note
Make sure that you have set the clock correctly.
1
In standby mode, press and hold TIMER until
[SET TIMER] (set timer) scrolls on the display.
» [SELECT SOURCE] (select source) scrolls
on the screen.
2
Press SOURCE repeatedly to select a source:
CD, FM, USB, iPod/iPhone or iPod/iPhone
playlist.
If iPod/iPhone playlist is selected as alarm
source, you need create a playlist called
“PHILIPS” in your iPod/iPhone.
If no playlist called “PHILIPS” is created
in the iPod/iPhone or no track is stored
in the playlist, the unit switches to iPod/
iPhone alarm source.
Press TIMERWRFRQÀUP
» The hour digits are displayed and begin to
blink.
3
4
Press / repeatedly to set hour, then press
TIMERDJDLQWRFRQÀUP
» The minute digits are displayed and begin
to blink.
5
Press / to set minute, then press TIMER to
FRQÀUP
» VOL (volume) is displayed and begins to
blink.
6
Press / to adjust volume, then press
TIMERWRFRQÀUP
» A clock icon is displayed.
Activate/deactivate alarm timer
1 In standby mode, press TIMER repeatedly to
activate or deactivate timer.
» If timer is activated, is displayed.
Tip
When the unit is turned on, press SLEEP
repeatedly to select a time period (in minutes).
» When sleep timer is activated, is
displayed.
» To deactivate sleep timer, press SLEEP again
until disappears.
Listen to external audio device
You can listen to an external audio device such as
MP3 player through this unit.
1 Connect the audio device.
For audio device with red/white audio
output sockets:
Connect a red/white audio cable (not
supplied) to the AUX IN sockets and to
the audio output sockets on the audio
device.
For audio device with headphone
sockets:
Connect the supplied MP3 Link cable
to the MP3 LINK socket and to the
headphone socket on the audio device.
2 Select MP3 LINK/AUX source.
3 Play the device.
Listen through headphone
1
Plug a headphone into the
unit.
socket on the
8 Product information
Note
Product information is subject to change without prior
notice.
6SHFLÀFDWLRQV
$PSOLÀHU
Rated Output Power
Frequency Response
Signal to Noise Ratio
Aux Input
2X50W RMS
30Hz-20kHZ
G%
1V RMS 20kohm
Alarm timer is not available in MP3 LINK mode.
If CD/USB/iPod/iPhone source is selected, yet no disc is
placed or no USB/iPod/iPhone connected, the system
switches to the tuner source automatically.
14
EN
DCM377_05_UM_V1.1.indd
14
2010-9-29
16:46:54
Disc
USB playability information
Audio DAC
Total Harmonic
Distortion
Frequency Response
S/N Ratio
Semiconductor
12cm/8cm
CD-DA, CD-R, CD-RW,
MP3-CD, WMA-CD
16Bits / 44.1kHz
<1% (1 kHz)
4Hz - 20kHz (44.1kHz)
>75dBA
Tuner (FM)
Tuning Range
Tuning grid
Sensitivity
- Mono, 26dB S/N Ratio
- Stereo, 46dB S/N Ratio
Search Selectivity
Total Harmonic Distortion
Signal to Noise Ratio
87.5 - 108MHz
50 KHz
<22 dBf
>43 dBf
>28 dBf
<3%
>55 dB
Speakers
Speaker Impedance
Speaker Driver
Sensitivity
6 ohm
5” woofer + 1” tweeter
>85dB/m/W
General information
AC power
Operation Power
Consumption
Eco Standby Power
Consumption
Audio Output
Headphone Output
USB Direct
Dimensions
- Main Unit (W x H x D)
- Speaker Box (W x H x D)
Weight
- With Packing
- Main Unit
- Speaker Box
220 - 240V, 50/60Hz
35W
:
1Vpp ± 0.1Vpp
3.5kohm
2x15mW 32ohm
Version 2.0 FS
Compatible USB devices:
USBÁDVKPHPRU\86%RU86%
86%ÁDVKSOD\HUV86%RU86%
memory cards (requires an additional card
reader to work with this unit)
Supported formats:
U6%RUPHPRU\ÀOHIRUPDW)$7)$7
FAT32 (sector size: 512 bytes)
MP3 bit rate (data rate): 32-320 Kbps and
variable bit rate
WMA v9 or earlier
Directory nesting up to a maximum of 8 levels
Number of albums/ folders: maximum 99
Number of tracks/titles: maximum 999
ID3 tag v2.0 or later
File name in Unicode UTF8 (maximum length:
64 bytes)
Unsupported formats:
Empty albums: an empty album is an album
WKDWGRHVQRWFRQWDLQ03:0$ÀOHVDQGLV
not be shown in the display.
8QVXSSRUWHGÀOHIRUPDWVDUHVNLSSHG)RU
H[DPSOH:RUGGRFXPHQWVGRFRU03ÀOHV
with extension .dlf are ignored and not played.
$$&:$93&0DXGLRÀOHV
'50SURWHFWHG:0$ÀOHVZDYPDPS
.mp4, .aac)
:0$ÀOHVLQ/RVVOHVVIRUPDW
Supported MP3 disc formats
ISO9660, Joliet
0D[LPXPWLWOHQXPEHUGHSHQGLQJRQÀOH
name length)
Maximum album number: 255
Supported sampling frequencies: 32 kHz,
44.1kHz, 48 kHz
Supported Bit-rates: 32~320 (kbps), variable
bit rates
160 x 242 x 237mm
160 x 242 x 222mm
10 kg
2 kg
2.85 x 2 kg
EN
DCM377_05_UM_V1.1.indd
15
English
Laser Type
Disc Diameter
Support Disc
15
2010-9-29
16:46:54
9 Troubleshooting
Warning
Never remove the casing of this apparatus.
To keep the warranty valid, never try to repair the
system yourself.
If you encounter problems when using this apparatus,
check the following points before requesting service. If
the problem remains unsolved, go to the Philips web
site (www.philips.com/welcome). When you contact
Philips, ensure that the apparatus is nearby and the
model number and serial number are available.
No power
Ensure that the AC power cord of the unit is
connected properly.
Ensure that there is power at the AC outlet.
As a power-saving feature, the system
switches off automatically 15 minutes after
track play reaches the end and no control is
operated.
No sound or poor sound
Adjust the volume.
Disconnect the headphones.
Check that the speakers are connected
correctly.
Check if the stripped speaker wires are
clamped.
Wait until the moisture condensation at the
lens has cleared.
Replace or clean the disc.
8VHDÀQDOL]HG&'RUFRUUHFWIRUPDWGLVF
&DQQRWGLVSOD\VRPHÀOHVLQ86%GHYLFH
7KHQXPEHURIIROGHUVRUÀOHVLQWKH86%
device has exceeded a certain limit. This
phenomenon is not a malfunction.
7KHIRUPDWVRIWKHVHÀOHVDUHQRWVXSSRUWHG
USB device not supported
The USB device is incompatible with the unit.
Try another one.
Poor radio reception
Increase the distance between the unit and
your TV or VCR.
Fully extend the FM antenna.
Connect an outdoor FM antenna instead.
Timer does not work
Set the clock correctly.
Switch on the timer.
Clock/timer setting erased
Power has been interrupted or the power
cord has been disconnected.
Reset the clock/timer.
No response from the unit
Disconnect and reconnect the AC power plug,
then turn on the unit again.
As a power-saving feature, the system
switches off automatically 15 minutes after
track play reaches the end and no control is
operated.
Remote control does not work
%HIRUH\RXSUHVVDQ\IXQFWLRQEXWWRQÀUVW
select the correct source with the remote
control instead of the main unit.
Reduce the distance between the remote
control and the unit.
Insert the battery with its polarities (+/– signs)
aligned as indicated.
Replace the battery.
Aim the remote control directly at the sensor
on the front of the unit.
No disc detected
Insert a disc.
Check if the disc is inserted upside down.
16
EN
DCM377_05_UM_V1.1.indd
16
2010-9-29
16:46:55
© 2010 Koninklijke Philips Electronics N.V.
All rights reserved.
DCM377_05_UM_V1.1
DCM377_05_UM_V1.1.indd
27
2010-9-29
16:46:43
">
