Sharkoon Tauron Red Edition Specification

Add to my manuals
23 Pages

advertisement

Sharkoon Tauron Red Edition Specification | Manualzz

Manual

tauron

Content

2. Package content

3. the case at a glance

4. Installation notes

5. rebuilding the HDD cages

6. Installation of a mainboard

7. Installation of a PSu

8. Installation of a HDD

9. Installation of an optical device

10. Installation of a 3.5" device

11. Installation of an add-on card

12. the pre-installed fans / using the fan control

13. Installation of additional fans / optimized airflow

Dear customer!

Congratulations for purchasing this premium quality SHARKOON product.

For a long life time and to take full advantage of this product we recommend you to read this manual completely.

Enjoy our product!

SHARKOON Technologies

11

14

15

17

19

4

8

3

3

9

21

21

22

Tauron

2

1. Features

• ATX case

• 2x 5.25" drive bays (external)

• 1x 5.25" or 3.5" drive bays (external)

• 7x 2.5" or 3.5" bays with removable mounting trays for HDDs (internal)

• Top I/O: 2x USB3.0, 2x USB2.0 and 2x audio, power and reset button, 2x fan speed controllers for

up to 6 fans

• 7 slots for add-on cards

• Acrylic side panel

• Plastic front panel with air inlet, drive bay covers in mesh design

• Quick fasteners for optical drives, mainboard mounting with installation opening for CPU coolers

• 4 openings for water cooling

• Cable management system

• Interior painting

• Removable HDD brackets support long VGA cards up to 42 cm

• Fan configuration:

Front panel

Rear panel

Top panel

2x 120 mm LED fan (pre-installed)

1x 120 mm fan (pre-installed)

1x 170 mm fan (pre-installed)

• Dimensions: 510 x 205 x 495 mm (L x W x H)

• Weight: ~9.5 kg

2. Package contents

• ATX case “Tauron”

• Manual flyer

• Accessory kit

Screws for mainboard mounting

Mounting screws for 2.5"

HDDs/SSDs

Screws for PSU mounting

Screws for HDD mounting

Note:

If you are missing any of the items listed above, please contact our customer service immediately: [email protected] (Germany and Europe) [email protected] (international).

Stand-offs for mainboard Internal USB3.0 adapter

Tauron 3

3. the case at a glance

Front panel a

C

B

A – 5.25" drive bays

B – 3.5" mounting bay

C – behind the mesh panel: 2x 120 mm LED fans

Side panel (closed/left) a

A – Acrylic side panel

Tauron

4

Side panel (opened/left) a a b

B

E

C D

A – Mainboard mounting panel

a – Installation opening for CPU coolers

b – Cable feedthrough

B – 5.25" drive bays

C – 3.5" mounting bay

D – Quick fasteners

E – HDD cages

Side panel (closed/right) a

B

A – Air inlet for CPU

B – Air inlet for HDDs

Tauron

5

Side panel (opened/right) a

B C

D b

E a

A – 5.25" drive bays

B – 3.5" mounting bay

C – Quick fasteners

D – HDD cages

E – Mainboard mounting panel

a – Installation opening for CPU coolers

b – Cable feedthrough

Rear panel a

D

B

C

A – Opening for I/O shield

B – Openings for water cooling

C – 120 mm fan

D – Slot bezels

E – PSU bracket

B

E

Tauron

6

Top panel a a e

B e a b c d

Bottom panel a a

C

A – Case feet

B – Air inlet for PSU

C – Fan bracket for 120 mm or 140 mm fan a

B a

A – On/off button

B – Top I/O:

a – 2x USB3.0

b – 2x audio

c – Reset button

d – 2x USB2.0

e – 2x fan control

C – under the mesh bezel:

170 mm fan

Tauron

7

The internal I/O connectors a B C D

E b a

F a b c d e

A – Audio connectors for:

a – HD Audio

b – AC’97

B – USB2.0 connector

C – 2x USB3.0 connectors

D – Fan control connector

E – Front-I/O power connector

F – Connectors for:

a – Power Switch

b – Power LED –

c – Power-LED +

d – HDD-LED

e – Reset-Switch

4. Installation notes

1. For further information on how to install the PC components, please also refer to their respective

instructions.

2. In order to guarantee full functionality of the fan controls and the front connectors, the front-I/O

power connector must be connected to the power supply.

Tauron

8

5. rearranging the HDD cages

The HDD cages of the case may be re-arranged, so that VGA cards up to 42 cm can be installed.

Delivery status

Removed HDD cages

Alternative HDD cage arrangements

Tauron

9

In order to remove the HDD cages, proceed as follows:

1. Unscrew the thumb screws on the back side of the case and remove both side panels.

2. Lift the attachment lever of the respective HDD cage (fig. 1) and drag the cage out of its fitting (fig. 1b).

fig. 1a fig. 1b

3. Slide the HDD cage into the respective bottom fitting of the case until the attachment lever locks

(fig. 2a and b).

fig. 2a fig 2b

Tauron

10

6. Installation of a mainboard

1. Unscrew the thumb screws on the back side of the case and remove both side panels. Lay down the

case sidewise on an even surface.

2. The mounting panel of the mainboard inside the case provides various mounting holes to fix the

standoffs (fig. 3).

Fig. 3

The mainboard contains special screw mounts (fig. 4).

Fig. 4

Tauron

11

Place the mainboard to the mounting panel. A standoff must be screwed into every hole on the mounting

panel visible through the mainboard’s screw openings.

3. Remove the mainboard and screw the standoffs into the their respective holes on the mounting panel

(fig. 5).

(Standoffs)

Fig. 5

4. Insert the I/O shield (delivered with the mainboard) into the I/O shield opening in the rear panel of the '

case.

Tauron

12

5. Place the mainboard back onto the standoffs and screw the mainboard to them (fig. 6).

(Screws for mainboard mounting)

Fig. 6

6. Plug the connectors of the case’s front bezel to the respective connectors of the mainboard (please refer

to your mainboard’s manual for further information).

Tauron

13

7. Installation of a PSu

1. Position the case in front of you and – from the inside – position the PSU against the PSU bracket on the

case’s rear panel (fig. 7).

Fig. 7

2. Screw the PSU to the case from the outside (fig. 8).

(Screws for PSU mounting)

Fig. 8

Tauron

14

8. Installation of a HDD

1. Take a mounting frame from one of the HDD cages (fig. 9).

Fig. 9 Mounting frame

2. Place an HDD into the mounting frame (connectors pointing backwards / fig. 10a and b).

Fig. 10a Fig. 10b

Tauron

15

3. Attach the HDD to the mounting frame from below (fig. 11a and b).

Fig. 11a Fig. 11b

4. Slide the mounting frame into the HDD cage until it locks (fig. 12).

Fig. 12

5. Connect the HDD to the PSU and the mainboard.

Tauron

16

9. Installation of an optical device

1. Remove the case’s front panel by gently pulling it towards you (fig. 13).

Fig. 13

2. Dismantle the 5.25" front bezel from the mounting bay by removing it from the front panel (fig. 14).

Fig. 14

Tauron

17

3. Place the front panel back onto the case.

4. Slide the optical drive into the case’s drive bay (fig. 15).

Fig. 15

5. Attach the optical device to the case from both sides using the quick fasteners (fig. 16).

Fig. 16

Note:

If you intend to transport the case, we recommend that you screw-in the built-in devices (additionally).

6. Connect the optical drive to the power supply and the mainboard.

Tauron

18

10. Installation of a 3.5" device

1. Remove the case’s front panel by gently pulling it towards you.

2. Dismantle the 3.5" front bezel by removing it from the front panel (fig. 17).

Fig. 17

3. Unlock the quick fasteners, which attach the mounting frame for 3.5” devices inside the case (fig. 18a)

and remove the mounting frame from the case (fig. 18b).

Fig. 18a

Fig. 18b

(Carefully remove an optionally present metal bezel covering the 3.5" drive bay by using a gripper.)

Tauron

19

4. Place the 3.5" device into the mounting frame for 3.5" devices and attach the device to the frame from

both sides (fig. 19).

Fig. 19

5. Slide the mounting frame with the installed 3.5" device into the case’s mounting bay (fig. 20a) and lock it

from both sides using the quick fasteners (fig. 20b).

Fig. 20a Fig. 20b

6. Connect the 3.5" device to the power supply and the mainboard.

7. Replace the front bezel to the case.

Tauron

20

11. Installation of an add-on card

1. Remove the anchor screw of the slot bezel and take it from the case.

2. Insert the add-on card into the respective slot of the mainboard and attach it to the case using the

anchor screw (fig. 21).

Fig. 21

3. Close the case.

12. the pre-installed fans / using the fan control

The pre-installed fans provide a 3-pin as well as a 4-pin power connector: a

B B

A – 3-pin power connector

B – 4-pin power connector

The 3-pin power connector lets you connect the respective fan to a matching power connector of the mainboard (in this case, the fan will be controlled by the mainboard) or a connector of the case’s fan control; in this case the fan speed can be adjusted by using the sliders of the fan controller.

Tauron 21

Fan connector of the fan control

Sliders of the fan control

13. Installation of an additional bottom panel fan / optimized airflow

The case provides the opportunity to install an additional 120 or 140 mm fan into the bottom panel.

Therefore proceed as follows:

1. Remove the bottom fitting for the HDD cages by loosening its four mounting screws und removing the

fitting from the case (fig. 23).

Fig. 23

Tauron

22

2. Place the fan against the respective bracket from the inside of the case.

3. Screw the fan to the attachment from the outside.

4. Connect the fan to the mainboard or the PSU.

Notes:

When installing fans, make sure that (cool) air is taken in on the front/bottom of the case and blown out on

its rear side/top. The PC components with the highest heat development should be placed directly within

the airflow.

Legal disclaimer:

As a continuing policy of product improvement at SHARKOON, the design and specifications are subject to change without prior notice. National product specifications may vary.

All rights reserved especially (also in extracts) for translation, reprinting, reproduction by copying or other technical means. Infringements will lead to compensation.

All rights reserved especially in case of assignation of patent or utility patent. Means of delivery and technical modifications reserved.

Disposal of your old product

Your product is designed and manufactured with high quality materials and components, which can be recycled and reused.

When this crossed-out wheeled bin symbol is attached to a product, it means the product is covered by the

European Directive 2002/96/EC.

Please be informed about the local separate collection system for electrical and electronic products.

Please act according to your local rules and do not dispose of your old products with your normal household waste. The correct disposal of your old product will help prevent potential negative consequences to the environment and human health.

© SHarKoon technologies 2011 www.sharkoon.com

Tauron

23

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement