LG | KM60020S | Operating instructions | LG KM60020S hob

Ceramic Glass HOB
Installation and Operating Instructions
KM60520S
KM60020S
To avoid the risk of accidents or damage to the HOB,
it is essential to read these operating instructions
before it is installed or used for the first time.
And please keep this manual for later reference.
P/No. :3828W5A8382
Dear Customer
Please read these operating instructions carefully.
Above all, please observe the “safety” section on the first few
pages.
Please retain these operating instructions for later reference.
Pass them on to any subsequent owners of the appliance.
The following symbols are used in the text:
Safety information
-- Warning: Information concerning your personal safety.
-- Important: Information on how to avoid damaging the
appliance.
Information and practical tips
Environmental information
1. These numbers indicate step by step how to use the appliance.
2. …
3. …
These operating instructions contain information on steps you
can take yourself to rectify a possible malfunction. Refer to the
section “What to do if...”.
2
Contents
Safety ....................................................................................... 4-7
Suitable Kitchenware .............................................................. 8-9
Description of the appliance ................................................... 10
Cooking zones and control ...................................................... 10
The key features of your appliance .........................................11
Operating Instructions ........................................................ 12-13
Before using for the first time ................................................... 12
Operating the hob .................................................................... 12
Outside Cooking Zone (Dual, Oval) Selection ......................... 13
Uses, Tables and Tips .............................................................. 14
Chart for Setting the Cooking Zones ........................................ 14
Automatic time limiter .............................................................. 15
Cleaning and Care................................................................ 16-17
Installation Instructions....................................................... 18-24
Technical data .......................................................................... 18
Regulations, Standards, Directives ......................................... 19
Safety instructions for the installer ........................................... 20
Electrical connection ................................................................ 21
Assembly ................................................................................. 22
Troubleshooting .........................................................................25
Service.........................................................................................26
3
Safety
The safety aspects of this appliance comply with accepted
technical standards and IEC Standards. However, as the
manufacturer we also believe it is our responsibility to
familiarize you with the following safety instructions.
Electrical Safety
• The installation and connection of the new appliance must only be
carried out by qualified personnel.
• Repairs to the appliance are only to be carried out by approved
service persons. Repairs carried out by inexperienced persons
may cause injury or serious malfunctioning. If your appliance
needs repairing, please contact your local Service Centre.
• This connection may be achieved by having the plug accessible or
by incorporation a switch in the fixed wiring in accordance with the
wiring rules.
Please follow these instructions, otherwise the warranty will not
cover any damage that may occur.
• Flush-mounted appliances may only be operated following
installation in suitable cabinets and workplaces which conform to
the relevant standards. This ensures sufficient protection against
electric shock as required by certification body.
• If your appliance malfunctions or fractures:
– switch off all cooking zones, and contact Service Center.
If the surface is cracked, switch off the appliance to avoid the
possibility of electric shock. Do not re-use your hob until the
glass surface has been changed.
When using Hob, never use aluminum foil, products wrapped in
aluminum foil, or deep frozen food in aluminum cookware.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard.
4
Child Safety
This appliance is not intended for use by young children or
infirm persons unless they have been adequately supervised by
a responsible person to ensure that they can use the appliance
safely.
Young children should be supervised to ensure that they do not
play with the appliance.
WARNING: Accessible parts may become hot during use.
Young children should be kept away.
The cooking zones will become hot when you cook. Therefore,
always keep small children away from the appliance.
Safety During Use
• This appliance may only be used for normal cooking and frying in
the home. It is not designed for commercial or industrial purposes.
• Do not use the hob to heat the room.
• Take care when plugging in electric appliances near the hob.
Connection leads must not come into contact with the hot surface.
• Overheated fats and oils catch fire quickly. You should supervise
cooking when preparing foods in fat or oil.
• Switch off the cooking zones after use.
• Always keep the control panels clean and dry.
• Never place combustible items on the hob.
• You must not keep any combustible items aerosol cans in a
drawer located under the hob.
• The service cables from electrical appliances must not touch the
hot plates. This could cause damage to the hob and cable
insulation.
5
Safety
Safety When Cleaning
• Always switch off the appliance before cleaning.
• For safety reasons do not clean the appliance with a steam jet or
high pressure cleaner.
• Clean the hob in accordance with the maintenance and cleaning
instructions in this manual.
• Do not use harsh abrasive cleaners or sharp metal scrapers to
clean the oven door glass since they can scratch the surface,
which may result in shattering of the glass.
How to avoid damage to the appliance
• Do not use the cooking area as a worktop or storage space.
• Please be careful the edges when moving pots and pans around.
• Do not have the cooking zones on with empty pans, or with no
pots or pans on them.
• Ceramic glass is very tough, and impervious to sharp temperature
changes, but is not unbreakable. It can be damaged if particularly
hard or sharp objects fall on to it.
• Be very cautious if using pots made of cast iron, or other pots with
rough edges or burrs. Moving these can cause scratches on
glass.
• If sugar or a mixture containing sugar falls onto a hot cooking
zone and melts, remove immediately, while still hot. If left to cool
down, it may damage the surface when removed.
Important: There is a risk of burning yourself when the glass
scraper is used on a hot cooking zone!
• Keep objects or materials liable to melt away from the ceramic
glass surface, for example, plastic utensils, aluminium foil, or
cooking wraps. If any other materials or foodstuffs have melted on
the ceramic glass surface, these should also be cleaned away
immediately.
6
Disposal of old appliances
Warning: Before disposing of old appliances please make them
inoperable so that they cannot be the source of danger.
To do this, have a qualified person disconnect the
appliance from the house circuitry.
To protect the environment, it is important that worn out appliances
are disposed of in the correct manner.
• The appliance must not be disposed of with household rubbish.
• You can obtain information about collection dates or public refuse
disposal sites from your local Council or Environmental Health
Office.
Note: Moisture coming from or appearing around Hob.
The moisture could be coming from the wood and hob when the
hob is operated initially or after long time of no operation.
This is not a fault with the Hob.
7
Suitable Kitchenware
Pots and pans
The better the pot, the better the cooking results.
• You can recognize good pots and pans by their bases. The base
should be as thick and flat as possible.
• When buying new pots and pans, pay particular attention to the
diameter of the base. Maunfacturers often only state the diameter
of the rim.
• Pots with aluminum, or copper bases can cause metallic
discolouring on the ceramic glass surface which is very difficult or
impossible to remove.
• Be very careful when using cast iron pots or pots with damaged
bases which are rough and or have burrs on them. Scratches can
occur if they are slid across the surface.
• When cold, pot bases are normally bowed slightly in wards
(concave). They should never be bowed outwards (convex).
• If you use special pots and pans (e.g., a pressure cooker,
simmering pan, wok etc.) please observe the manufacturer’s
instructions.
General information
• The base should always be clean and dry.
• In order to avoid ugly scratches on the ceramic glass cooking
surface, do not slide pots and pans around but lift them up instead
when changing positions.
• Scratches can result from grains of sand (e.g., after washing out
vegetables) which are dragged with the pot across the cooking
surface.
• Always use large pots for dishes with lots of liquid so that nothing
can boil over.
8
Tips on saving energy
You will save valuable energy by observing the following points:
• Always position pots and pans before you switch on the cooking
zone.
• Dirty cooking zones and pot bases increase the power
consumption.
• Whenever possible, always have the lid firmly placed on the pots
and pans so that they are completely covered.
• Switch off the cooking zones before the end of the cooking time to
use the residual heat for keeping food warm or for melting
purposes.
• The base of the pot should have the same size as the cooking
zone.
• Using a pressure cooker shortens the cooking times by up to 50%.
9
Description of the Appliance
Cooking zones and control
KM60520S
Cooking zone
1200W 15cm
Cooking zone
2400W 26cm
Cooking zone
2200W (Dual)
22cm
Cooking zone
1200W 15cm
Indicators
KM60020S
Cooking zone
1200W 15cm
Cooking zone
1800W 19cm
Cooking zone
2300W 22cm
Cooking zone
1200W 15cm
Indicators
10
Oven Control panel
Oven model : LE641152
Heater control knob
Oven model : LE641122
Heater control knob
* Heater control knob : Set and adjust the power level.
The Key Features of Your Appliance
• Cooking zones: The appliance is fitted with ceramic glass.
• Easy cleaning: The advantage of the ceramic glass cooking
surface is their accessibility for cleaning.
The flat surface is easy to clean.
• Indicators: Digital indicators provide information about settings
made, functions activated, as well as any residual heat of the
corresponding cooking zone.
• Residual heat indicator: An h for residual heat is shown in the
display if the cooking zone becomes so hot that there is a risk of
burning. As the burner cools down further, the display changes to
. The display remains lit until the burner cooles sufficiently.
11
Operating Instructions
Before using for the first time
Initial Cleaning
Wipe the ceramic glass surface with a damp cloth and ceramic
cooktop glass cleaner.
Important: Do not use any caustic, abrasive cleaners!
The surface could be damaged.
Operating the hob
For setting and adjusting the power level ( 1 to 9 ) for cooking,
dial the relative cooking zone knob in the oven control panel.
5
4 3
2
6
1
0
2
Heat Level Setting
To select the required cooking zone and set the heat level, dial the
corresponding burner’s knob into clockwise.
5
6
4 3
2
8
9
7 6
5
Dial the Knob into Clockwise
To increase the heat power level dial the knob into
counterclockwise.
12
Outside Cooking Zone (Dual, Oval) Selection
By switching outside heater on or off, the effective heating surface
can be matched to the size of the cookware.
To switch on outside heater, the inside heater must be switched on
power level 9.
And then dial the desired Heater’s Control knob more into
clockwise.
The indicator of outside heater will be on.
9 8
7
1
0
2
To switch off outside heater, set the heaters power level 0 and then
set inside heater desired power level one more time.
13
Uses, Tables and Tips
Chart for Setting the Cooking Zones
Heat setting
9
7-9
6-7
Heating Up
Heavy
Browning
Deep fat
frying
Baking
Frying
4-5
Boil
3-4
Steaming
2-3
Simmering
1-2
Melting
0
suitable for
Bringing liquid to a boil.
Browning meat, heat oil for deep fat
frying or sauteing.
Maintaining fast boil for large
amounts of liquids.
Frying meat, schnitzel, cordon bleu,
chops, pancakes, rissoles, roux,
mild roasting, fried sausages, liver,
eggs.
Cooking larger quantities of food,
stews and soups, steaming
potatoes, cooking meat stock or
bouillon
Steaming vegeables or braising
meat, cooking rice pudding
Simmering rice or milk-based
dishes, steaming smaller quantities
of potatoes or vegetables, heating
up ready-to-serve meals.
Fluffy omelettes, egg royale, Sauce
hollandaise, keeping dishes warm,
melting butter, chocolate, honey
gelatin
Off setting
Note:
The heat setting indicated in the table above is only guidelines for
your reference. You need to adjust the heat settings to the pan and
food conditions.
14
Automatic time limiter
If a element is in constant use for a long time without the setting
being changed, the automatic time limiter is activated.
Then, power level is set 0 automatically.
Changing power level will reset the burner. The following table
shows the automatic limiter activation times.
Heat setting
max
1
2
6h
3
4
5h
15
5
4h
6
7
1.5h
8
9
Cleaning and care
Light Soiling
1. Wipe the ceramic glass surface with a damp cloth and a little
cooktop cleaner.
2. Then rub dry with a clean cloth. Remnants of cleaner must not be
left on the surface.
3. Thoroughly clean the entire ceramic glass cooking surface once
a week with a commercially available ceramic glass or stainless
steel cleaner.
4. Then wipe the ceramic glass surface using plenty of clean water
and rub dry with a clean fluff-free cloth.
Stubborn Soiling
1. To remove food that has boiled over or stubborn splashes, use a
glass scraper.
2. Place the glass scraper at an angle to the ceramic glass surface.
3. Remove soiling by sliding the blade across the area.
You can obtain glass scrapers and ceramic glass cleaners
which are suitable for glass ceramic, e.g. CERA CLEAN, cerafix, sidol for ceran+steel, from your local Hardware Centre.
16
Problem Soils
1. Remove sugar, melted plastic, aluminium foil or other meltable
materials with a glass scraper immediately and while still hot.
Important: There is a risk of burning yourself when the
glass scraper is used on a hot cooking zone!
2. Then clean the hob normally when it has cooled down.
If the cooking zone on which something has melted has already
cooled down, warm it up again for cleaning.
Scratches or dark marks on the ceramic glass surface, caused
by a pan base with sharp edges, cannot be removed. However,
they do not impair the function of the hob.
Since the heat is generated in the pan, food or foodstuffs
possibly on the glass ceramic surface are not burned in as
badly.
Important: Cleaning agents must not come into contact with
the hot ceramic glass surface! All cleaning agents must be
removed with plenty of clean water after cleaning because they
can have a caustic effect when the rings are next heated!
Do not use any aggressive cleaners such as grill or oven
sprays, coarse scourers or abrasive pan cleaners.
Clean the ceramic glass surface after each use when it is warm
to the touch or cold. This will avoid spillages becoming burned
on. Remove scale and
water marks, fat spots
and discolouration with a
metallic shimmer using a
commercially available
ceramic glass or stainless
steel cleaner.
17
Installation Instructions
Technical Data
Important! The new appliance may only be installed and
connected by a registered specialist.
Please observe these instructions, otherwise the warranty will not
cover any damage that may occur.
Appliance dimensions
Width
Depth
Height
575mm
515mm
40mm
Worktop cut-out dimensions
Width
Depth
Corner radius
560mm
500mm
5mm
Cooking rings
Position
Front left
Rear left
Rear right
Front right
Diameter
KM60520S KM60020S
210mm
210mm
140mm
140mm
260mm
180mm
140mm
140mm
Connection voltage
Maximum connected load power
18
Power
KM60520S KM60020S
2200W
2300W
1200W
1200W
2400W
1800W
1200W
1200W
220~240V 1AC/2NAC
50Hz
7.0kW (KM60520S)
6.5kW (KM60020S)
Regulations, Standards, Directives
This appliance meets the following standards:
• EN 60335-1 and EN 60335-2-6
relating to the safety of electrical appliances for household use
and similar purposes and
• EN 60350
Methods for measuring performance.
• EN 55014-2
• EN 55014-1
• EN 61000-3-2
• EN 61000-3-3
relating to basic requirements for electro-magnetic compatibility
protection (EMC)
This appliance complies with the following EU Directives:
• 73/23/EWG dated 19.02.1973 (Low Voltage Directive)
• 89/336/EWG dated 03.05.1989 (EMC Directive including
Amending Directive 92/31/EWG).
• 93/68/EWG CE Labelling Directive
19
Installation Instructions
Safety Instructions for the Installer
• A device must be provided in the electrical installation which
allows the appliance to be disconnected from the mains at all
poles with a contact opening width of at least 3 mm Suitable
isolation devices include line protecting cut-outs, fuses (screw
type fuses are to be removed from the holder), earth leakage trips
and contactors.
• In respect of fire protection, this appliance corresponds to type
Y (EN 60335-2-6). Only this type of appliance may be installed
with a high cupboard or wall on one side.
• Drawers may not be fitted underneath the hob.
• The installation must guarantee shock protection.
• The kitchen unit in which the appliance is fitted must satisfy the
stability requirements of DIN 68930.
• For protection against moisture, all cut surfaces are to be sealed
with a suitable sealant.
• On tiled work surfaces, the joints in the area where the hob sits
must be completely filled with grout.
• On natural, artificial stone, or ceramic tops, the snap action
springs must be bonded in place with a suitable artificial resin or
mixed adhesive.
• Ensure that the seal is correctly seated against the work surface
without any gaps. Additional silicon sealant must not be applied;
this would make removal more difficult when servicing.
• The hob must be pressed out from below when removed.
• Clean the work surface in the area of the cut-out.
• Sealing tape is mounted on the ceramic Glass initially.
• Drawers may only be installed with a protective floor directly under
the appliance.
20
Electrical Connection
Before connecting, check that the nominal voltage of the appliance,
that is the voltage stated on the rating plate, corresponds to the
available supply voltage. The rating plate is located on the lower
casing of the hob.
Shut off power to circuit before connecting hob wires to circuit.
The heating element voltage is AC230V~. The appliance also works
perfectly with AC220V~ and AC 240V~.
Once connected to the mains supply check that all cooking
zones are ready for use by briefly switching each on in turn at
the maximum setting.
Loose and inappropriate plug and socket connections can lead to
overheating of the plug.
- Fit plug and socket connections together properly.
21
Installation Instructions
Assembly
Bracing
<Fig. 1>
Remove the
bracing from the
furniture for hob
airflow.
Furniture
min. 50 mm
min. 50 mm
<Fig. 2>
min. 50 mm
min. 5 mm
Follow Fig.2 for
minimum
required surface
clearances.
22
CL
5
5
15
15
5
15
55
1
<Fig. 3>
Cabinet cutout and mounting clip locations.
23
CL
Installation Instructions
<Fig. 4>
Caution: It is important to keep 20 mm distance between hob case
and combustible surface.
Make sure hob is fully seated, with foam tape compressed against
countertop.
<Fig. 5>
To remove the hob, it must be pressed out from below.
24
Troubleshooting
Malfunctions often have simple explanations. Please read the
following instructions before calling the after-sales service:
Problem description
Possible cause or Remedies
Hob does not work.
• Check below.
– Connection and Main Switch.
– The correponding cooking zone is
selected.
– The desired heat setting is selected.
Flashing
• When initially powered up or after power
outage. Touch the on/off key to fix.
h will flash for 60 minutes.
• The hotplate temperature is controlled by
switching the heat on and off, this means
that it is not always possible to see the
red, glowing heat. If you select a low heat
setting, the heat will switch off more often
than at higher heat settings. The heat also
switches on and off at the highest setting.
h
Burner not glowing
red
Repairs
Repairs may only be carried out by service technicians.
25
Service
Packaging and old appliances
Your new appliance was protected by suitable packaging while it
was on its way to you. All materials used for this purpose are
environmentally friendly and can be recycled. Please make a
contribution to protecting the environment by disposing of the
packaging appropriately.
Old appliances are not worthless rubbish.
Environmentally conscious recycling can reclaim valuable raw
materials.
Before disposing of your old appliance, please make sure that it is
unusable, or label it with a sticker stating "Caution, scrap".
Up-to-date information on how to dispose of your old appliance and
the packaging from the new one can be obtained from your retailer
or local authority.
Contact Service center
Please quote the model name of your appliance when contacting
the service center. The name plate can be found under the
appliance. When you contact us we need to know.
• Your name
• Address and post code
• Telephone number
• Clear and concise details of the fault
• Model No. and serial No.
26
Memo
27
FOR WARRANTY SERVICE PLEASE CONTACT THE RETAILER FROM WHOM
YOU PURCHASED YOUR UNIT OR CONTACT LG SERVICE
LG ELECTRONICS S.A.(Pty) Ltd.
P.O.BOX 473
ISANDO
1600
LG Service center
Phone: 0800-LGLGLG (0800-545454)
http://www.lge.co.za
220V-240V 1 AC/2NAC 50Hz
Model : KM60520S / KM60020S
Made In Korea
Max. : 7.0kW (KM60520S)
6.5kW (KM60020S)
P/No.:3828W5A8382
Download PDF

advertising