Peerless ACC200 mounting kit Manual
Add to my manuals3 Pages
Peerless ACC200 is a versatile mount designed for indoor use, enabling you to securely attach various equipment to walls or ceilings made of wood, concrete, or concrete blocks. It provides a sturdy and reliable foundation for mounting electronic devices, ensuring their stability and safety. With its simple installation process and clear instructions, the ACC200 allows you to easily set up your equipment without hassle.
advertisement
Supplemental Instructions - Wall Plate and Ceiling Plate Attachment
IMPORTANT!
Read entire instruction sheet before you start installation and assembly.
Peerless Industries, Inc.
1980 Hawthorne Avenue
Melrose Park, IL 60160
WARNING! Installer must verify that the wall or ceiling will safely support the combined weight of all attached equipment and hardware.
For customer service call
1-800-729-0307 or 708-865-8870.
This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury.
Note: For each step see corresponding illustration.
IMPORTANT: IT IS THE RESPONSIBILITY OF THE INSTALLER
TO VERIFY THAT THE MOUNTING SURFACE WILL SAFELY
SUPPORT THE COMBINED LOAD OF ALL ATTACHED
HARDWARE AND COMPONENTS.
#14 x 2.5"(6mm x 65mm) wood screws for attachment to wood studs, wood beams, or wood ceiling joists are provided with most Peerless products in quantities of
2, 3, or 4, depending on the product and application.
For attachment to solid concrete or concrete block order one of the concrete anchor accessory kits pictured (some products may already include concrete anchors). Accessory kits contain RAWL TM #5005 OR
HILTI TM HL814 CONCRETE EXPANSION ANCHORS.
[.312 x 1.625 (8mm x 41mm)].
For ceiling plate attachment to a concrete ceiling drill
5/16" (8mm) dia. holes to a minimum depth of 1 3/4"
(45mm). Attach using concrete expansion anchors.
Hammer in concrete expansion anchors, then tighten to 80 in. lbs. (9 N.M.) torque using a
10mm wrench.
NOT FOR ATTACHMENT TO CONCRETE CEILINGS
COVERED WITH PLASTER, DRYWALL, OR
OTHER FINISHING MATERIAL!
For ceiling plate attachment to a wood joist finished ceiling, exposed wood joists, or a wood beam ceiling locate joist centers using a stud finder. Drill 5/32"
(4mm) dia. holes 2.5" (65mm) deep into joist centers.
Attach ceiling plate using #14 x 2.5" (6mm x 65mm) wood screws.
CAUTION: Tighten wood screws so ceiling plate is firmly attached. But DO NOT TIGHTEN WITH EXCES-
SIVE FORCE! Overtightening can cause stress damage to wood screws greatly reducing their holding power! Tighten to 80 in. lbs. (9 N.M.) maximum torque.
For wall plate attachment to a solid concrete or
concrete block wall drill 5/16" (8mm) dia. holes to a minimum depth of 1 3/4" (45mm). Attach with concrete expansion anchors. If attaching to concrete block
DO NOT DRILL HOLES INTO MORTAR JOINTS!
Hammer in concrete expansion anchors, then tighten to 80 in. lbs. (9 N.M.) torque using a
10mm wrench.
NOT FOR ATTACHMENT TO CONCRETE WALLS
COVERED WITH PLASTER, DRYWALL, OR
OTHER FINISHING MATERIAL!
For wall plate attachment to a wood stud wall or
beam locate stud center using a stud finder. Drill 5/32"
(4mm) dia. holes 2.5" (65mm) deep into stud center.
Attach wall plate using #14 x 2.5" (6mm x 65mm) wood screws.
CAUTION: Tighten wood screws so wall plate is firmly attached. But DO NOT TIGHTEN WITH EXCESSIVE
FORCE! Overtightening can cause stress damage to wood screws greatly reducing their holding power!
Tighten to 80 in. lbs. (9 N.M.) maximum torque.
ACC200 ACC205
ACC210
ISSUED: 6-25-96 SHEET #: 120-8012-4 12-15-09
1 1 1 1 1 of 33333
10mm
∅ 5/16"(8mm)
∅ 5/32"(4mm)
ISSUED: 6-25-96 SHEET #: 120-8012-4 12-15-09
∅ 5/16"(8mm)
10mm
∅ 5/32"(4mm)
ISSUED: 6-25-96 SHEET #: 120-8012-4 12-15-09
© 2009 Peerless Industries, Inc. All rights reserved.
Peerless is a trademark of Peerless Industries, Inc.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project