Hikvision DS-8108HFHI-ST User manual

Document

Digital Video Recorder
User Manual
UD.6L0202D1252A01
User Manual of Digital Video Recorder
Hikvision&reg; Network Digital Video Recorder User Manual
This manual, as well as the software described in it, is furnished under license and may be used or copied only
in accordance with the terms of such license. The content of this manual is furnished for informational use only,
is subject to change without notice, and should not be construed as a commitment by Hangzhou Hikvision
Digital Technology Co., Ltd. (Hikvision). Hikvision assumes no responsibility or liability for any errors or
inaccuracies that may appear in the book.
Except as permitted by such license, no part of this publication may be reproduced, stored in a retrieval system,
or transmitted, in any form or by any means, electronic, mechanical, recording, or otherwise, without the prior
written permission of Hikvision.
HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
REGARDING THE HIKVISION SOFTWARE. HIKVISION DOES NOT WARRANT, GUARANTEE, OR
MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE
HIKVISION
SOFTWARE
IN
TERMS
OF
ITS
CORRECTNESS,
ACCURACY,
RELIABILITY,
CURRENTNESS, OR OTHERWISE. THE ENTIRE RISK AS TO THE RESULTS AND PERFORMANCE OF
THE HIKVISION SOFTWARE IS ASSUMED BY YOU. THE EXCLUSION OF IMPLIED WARRANTIES IS
NOT PERMITTED BY SOME STATES. THE ABOVE EXCLUSION MAY NOT APPLY TO YOU.
IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE
TO YOU FOR ANY CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES (INCLUDING
DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS
INFORMATION, AND THE LIKE) ARISING OUT OF THE USE OR INABILITY TO USE THE HIKVISION
SOFTWARE EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR
CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATIONS MAY NOT APPLY TO
YOU.
2
User Manual of Digital Video Recorder
Regulatory information
FCC information
FCC compliance : This equipment has been tested and found to comply with the limits for a digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with &quot;CE&quot; and comply therefore with
the applicable harmonized European standards listed under the Low Voltage Directive 2006/95/EC, the EMC
Directive 2004/108/EC, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal
waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase
of equivalent new equipment, or dispose of it at designated collection points. For more information see:
www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal
waste in the European Union. See the product documentation for specific battery information. The battery is
marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg).
For proper recycling, return the battery to your supplier or to a designated collection point. For more
information see: www.recyclethis.info.
3
User Manual of Digital Video Recorder
Preventive and Cautionary Tips
Before connecting and operating your DVR, please be advised of the following tips:
•
•
•
•
•
Ensure unit is installed in a well-ventilated, dust-free environment.
Unit is designed for indoor use only.
Keep all liquids away from the DVR.
Ensure environmental conditions meet factory specifications.
Ensure unit is properly secured to a rack or shelf. Major shocks or jolts to the unit as a result of dropping it
may cause damage to the sensitive electronics within the unit.
•
•
•
•
Use the DVR in conjunction with an UPS if possible.
Power down the unit before connecting and disconnecting accessories and peripherals.
A factory recommended HDD should be used for this device.
Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or
equivalent type only. Dispose of used batteries according to the instructions provided by the battery
manufacturer.
4
User Manual of Digital Video Recorder
Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact
dealer.
This manual is applicable to the models listed in the following table.
Series
Model
Type
7200HFHI-SL
DS-7204HFHI-SL
Network DVR
DS-7208HFHI-SL
7200HFHI-SE
DS-7204HFHI-SE
Network DVR
DS-7208HFHI-SE
7200HFHI-ST
DS-7204HFHI-ST
Network DVR
DS-7208HFHI-ST
7300HFHI-ST
DS-7304HFHI-ST
Network DVR
DS-7308HFHI-ST
DS-7316HFHI-ST
8100HFHI-ST
DS-8104HFHI-ST
DS-8108HFHI-ST
DS-8116HFHI-ST
5
Network DVR
User Manual of Digital Video Recorder
Product Key Features
General
 Support HD-SDI camera connection;
 Each channel supports dual-stream. Main stream supports up to 1080P resolution and sub-stream
supports up to 4CIF resolution;
 Independent configuration for each channel, including resolution, frame rate, bit rate, image quality,
etc.
 Encoding for both video stream and video &amp; audio stream; audio and video synchronization during
composite stream encoding;
 Watermark technology;
Local Monitoring
 Simultaneous HDMI, VGA and CVBS outputs (no CVBS output for DS-7200HFHI-SL,
DS-7200HFHI-SE and DS-7200HFHI-ST);
 HDMI output and VGA output at up to 1920*1080 resolution.
 1/4/6/8/9/16 screen live view is supported, and the display sequence of screens is adjustable.
 Live view screen can be switched in group and manual switch and automatic cycle live view are also
provided, the interval of automatic cycle can be adjusted.
 Quick setting menu is provided for live view.
 The selected live view channel can be shielded.
 Motion detection, video-tampering detection, video exception alarm and video loss alarm functions.
 Privacy mask;
 Several PTZ protocols supported; PTZ preset, patrol and pattern.
 Zooming in/out by clicking the mouse and PTZ tracing by dragging mouse;
HDD Management
 For DS-7200HFHI-SL series, 1 SATA hard disk can be connected; for DS-7200HFHI-SE and
DS-7200HFHI-ST series, up to 2 SATA hard disks can be connected; for DS-7300HFHI-ST series, 4
SATA hard disks and 1 eSATA disk can be connected; and for DS-8100HFHI-ST series, 8 SATA hard
disks and 1 eSATA disk can be connected. (Each disk with a maximum of 4TB storage capacity.)
 8 network disks (8 NAS disks, or 7 NAS disks+1 IP SAN disk) can be connected.
 Support eSATA disks for recording or backup.
 Support S.M.A.R.T. and bad sector detection.
 Support HDD standby function;
 HDD property: redundancy, read-only, read/write (R/W).
 HDD group management;
 HDD quota management; different capacity can be assigned to different channels.
Recording and Playback
 Holiday recording schedule configuration;
 Cycle and non-cycle recording modes;
 Normal and event video encoding parameters;
 Multiple recording types: manual, normal, alarm, motion, motion | alarm, motion &amp; alarm;
 8 recording time periods with separated recording types;
 Pre-record and post-record for motion detection triggered recording, and pre-record time for schedule
6
User Manual of Digital Video Recorder
and manual recording;
 Searching record files by events (alarm input/motion detection);
 Customization of tags, searching and playing back by tags;
 Locking and unlocking of record files;
 Local redundant recording;
 Searching and playing back record files by channel number, recording type, start time, end time, etc.;
 Smart search for the selected area in the video when playback;
 Zooming in for any area when playback;
 Reverse playback of multi-channel.
 Supports pause, fast forward, slow forward, skip forward, and skip backward when playback, locating
by dragging the mouse on the progress bar;
 Up to 16-ch synchronous playback at 1080P;
Backup
 Export data by a USB, SATA or eSATA device;
 Export video clips when playback;
 Management and maintenance of backup devices;
Alarm and Exception
 Configurable arming time of alarm input/output.
 Alarm for video loss, motion detection, tampering, abnormal signal, video input/recording resolution
mismatch, illegal login, network disconnected, IP confliction, record exception, HDD error, and HDD
full, etc.
 Alarm triggers full screen monitoring, audio alarm, notifying surveillance center, sending email and
alarm output.
 Automatic restore when system is abnormal.
Other Local Functions
 Users can operate by mouse and remote control.
 Three-level user management; admin user can create many operating account and define their
operating permission, which includes the permission to access any channel;
 Completeness of operation, alarm, exceptions and log writing and searching;
 Manually triggering and clearing alarms.
 Importing and exporting of configuration file of devices;
 Getting cameras type information automatically.
Network Functions
 1
self-adaptive
10M/100M
network
interface
for
DS-7204HFHI-SL;
2
self-adaptive
10M/100M/1000M network interfaces for DS-8100HFHI-ST series, and various working modes are
configurable: multi-address, load balance, network fault tolerance, etc.; and 1 self-adaptive
10M/100M/1000M network interface for other models;
 IPv6 is supported;
 TCP/IP protocol, PPPoE, DHCP, DNS, DDNS, NTP, SADP, SMTP, SNMP, NFS, iSCSI and UPnP™
are supported;
 TCP, UDP and RTP for unicast;
 Auto/Manual port mapping by UPnPTM.
 Remote search, playback, download, locking and unlocking the record files, and downloading files
broken transfer resume;
7
User Manual of Digital Video Recorder
 Remote parameters setup; remote import/export of device parameters;
 Remote viewing of the device status, system logs and alarm status;
 Remote keyboard operation;
 Remote locking and unlocking of control panel and mouse;
 Remote HDD formatting and program upgrading;
 Remote system restart and shutdown;
 Support upgrading via remote FTP server;
 RS-232, RS-485 transparent channel transmission.
 Alarm and exception information can be sent to the remote host;
 Remotely start/stop recording.
 Remotely start/stop alarm output.
 Remote PTZ control.
 Remote JPEG capture.
 Two-way audio and voice broadcasting.
 Embedded WEB server.
Development Scalability
 SDK for Windows and Linux system;
 Source code of application software for demo;
 Development support and training for application system;
8
User Manual of Digital Video Recorder
Table of Contents
Product Key Features ................................................................................................................................. 6
Chapter 1 Introduction ................................................................................................................................ 12
1.1
Front Panels ................................................................................................................................... 13
1.2
IR Remote Control Operations ...................................................................................................... 20
1.3
USB Mouse Operation .................................................................................................................. 22
1.4
Input Method Description .............................................................................................................. 23
1.5
Rear Panel ..................................................................................................................................... 24
Chapter 2 Getting Started ............................................................................................................................. 27
2.1
Starting Up and Shutting Down the DVR...................................................................................... 28
2.2
Using the Wizard for Basic Configuration..................................................................................... 30
Chapter 3 Live View ...................................................................................................................................... 34
3.1
Introduction of Live View ............................................................................................................. 35
3.2
Operations in Live View Mode...................................................................................................... 36
3.2.1
Front Panel Operation .......................................................................................................... 36
3.2.2
Using the Mouse in Live View............................................................................................. 37
3.2.3
Using an Auxiliary Monitor ................................................................................................. 38
3.2.4
Main/Aux Output Switching ................................................................................................ 38
3.2.5
Quick Setting Toolbar in Live View Mode .......................................................................... 39
3.3
Channel-zero Encoding ................................................................................................................. 41
3.4
Adjusting Live View Settings ........................................................................................................ 42
3.5
User Logout ................................................................................................................................... 43
Chapter 4 PTZ Controls............................................................................................................................... 44
4.1
Configuring PTZ Settings.............................................................................................................. 45
4.2
Setting PTZ Presets, Patrols &amp; Patterns......................................................................................... 46
4.3
4.2.1
Customizing Presets ............................................................................................................. 46
4.2.2
Calling Presets ..................................................................................................................... 47
4.2.3
Customizing Patrols ............................................................................................................. 48
4.2.4
Calling Patrols ..................................................................................................................... 49
4.2.5
Customizing Patterns ........................................................................................................... 50
4.2.6
Calling Patterns .................................................................................................................... 51
PTZ Control Panel ......................................................................................................................... 52
Chapter 5 Record Settings ........................................................................................................................... 53
5.1
Configuring Encoding Parameters ................................................................................................. 54
5.2
Configuring Record Schedule ....................................................................................................... 57
5.3
Configuring Motion Detection Record .......................................................................................... 61
5.4
Configuring Alarm Triggered Record ............................................................................................ 63
5.5
Manual Record .............................................................................................................................. 65
5.6
Configuring Holiday Record ......................................................................................................... 66
5.7
Configuring Redundant Recording ................................................................................................ 68
5.8
Configuring HDD Group for Recording ........................................................................................ 70
5.9
Files Protection .............................................................................................................................. 71
9
User Manual of Digital Video Recorder
Chapter 6 Playback........................................................................................................................................ 73
6.1
6.2
Playing Back Record Files ............................................................................................................ 74
6.1.1
Playing Back by Channel ..................................................................................................... 74
6.1.2
Playing Back by Time .......................................................................................................... 76
6.1.3
Playing Back by Event Search ............................................................................................. 78
6.1.4
Playing Back by Tag ............................................................................................................ 81
6.1.5
Playing Back by System Logs ............................................................................................. 83
6.1.6
Playing Back External File .................................................................................................. 85
Auxiliary Functions of Playback ................................................................................................... 86
6.2.1
Playing Back Frame by Frame ............................................................................................. 86
6.2.2
Smart Search ........................................................................................................................ 86
6.2.3
Digital Zoom........................................................................................................................ 88
6.2.4
Reverse Playback of Multi-channel ..................................................................................... 88
Chapter 7 Backup ......................................................................................................................................... 90
7.1
7.2
Backing up Record Files ............................................................................................................... 91
7.1.1
Quick Export ........................................................................................................................ 91
7.1.2
Backing up by Normal Video Search ................................................................................... 92
7.1.3
Backing up by Event Search ................................................................................................ 97
7.1.4
Backing up Video Clips ..................................................................................................... 101
Managing Backup Devices .......................................................................................................... 104
Chapter 8 Alarm Settings .......................................................................................................................... 107
8.1
Setting Motion Detection............................................................................................................. 108
8.2
Setting Sensor Alarms ................................................................................................................. 111
8.3
Detecting Video Loss................................................................................................................... 114
8.4
Detecting Video Tampering ......................................................................................................... 116
8.5
Handling Exceptions ................................................................................................................... 118
8.6
Setting Alarm Response Actions ................................................................................................. 119
8.7
Triggering or Clearing Alarm Output Manually .......................................................................... 121
Chapter 9 Network Settings ........................................................................................................................ 122
9.1
Configuring General Settings ...................................................................................................... 123
9.2
Configuring Advanced Settings ................................................................................................... 125
9.2.1
Configuring PPPoE Settings .............................................................................................. 125
9.2.2
Configuring DDNS ............................................................................................................ 125
9.2.3
Configuring NTP Server .................................................................................................... 129
9.2.4
Configuring SNMP ............................................................................................................ 130
9.2.5
Configuring UPnP™ .......................................................................................................... 130
9.2.6
Configuring the Remote Alarm Host ................................................................................. 132
9.2.7
Configuring Multicast ........................................................................................................ 133
9.2.8
Configuring RTSP.............................................................................................................. 133
9.2.9
Configuring Server and HTTP Ports .................................................................................. 134
9.2.10 Configuring Email ............................................................................................................. 134
9.3
Checking Network Traffic ........................................................................................................... 137
9.4
Configuring Network Detection .................................................................................................. 138
9.4.1
Testing Network Delay and Packet Loss ............................................................................ 138
10
User Manual of Digital Video Recorder
9.4.2
Exporting Network Packet ................................................................................................. 138
9.4.3
Checking Network Status................................................................................................... 140
9.4.4
Checking Network Statistics .............................................................................................. 140
Chapter 10 HDD Management ................................................................................................................. 142
10.1 Initializing HDDs ........................................................................................................................ 143
10.2 Managing Network HDD ............................................................................................................ 144
10.3 Managing eSATA ........................................................................................................................ 146
10.4 Managing HDD Group ................................................................................................................ 147
10.4.1 Setting HDD Groups .......................................................................................................... 147
10.4.2 Setting HDD Property ........................................................................................................ 148
10.5 Configuring Quota Mode............................................................................................................. 150
10.6 Checking HDD Status ................................................................................................................. 152
10.7 Checking S.M.A.R.T Information ............................................................................................... 153
10.8 Detecting Bad Sector ................................................................................................................... 154
10.9 Configuring HDD Error Alarms .................................................................................................. 155
Chapter 11 Camera Settings ..................................................................................................................... 156
11.1 Configuring OSD Settings ........................................................................................................... 157
11.2 Configuring Privacy Mask........................................................................................................... 158
Chapter 12 DVR Management and Maintenance ................................................................................... 159
12.1 Viewing System Information ....................................................................................................... 160
12.1.1 Viewing Device Information .............................................................................................. 160
12.1.2 Viewing Camera Information ............................................................................................. 160
12.1.3 Viewing Record Information ............................................................................................. 160
12.1.4 Viewing Alarm Information ............................................................................................... 161
12.1.5 Viewing Network Information ........................................................................................... 161
12.1.6 Viewing HDD Information ................................................................................................ 162
12.2 Searching and Exporting Log Files ............................................................................................. 163
12.3 Importing/Exporting Configuration Files .................................................................................... 165
12.4 Upgrading System ....................................................................................................................... 166
12.4.1 Upgrading by Local Backup Device .................................................................................. 166
12.4.2 Upgrading by FTP ............................................................................................................. 166
12.5 Restoring Default Settings ........................................................................................................... 167
Chapter 13 Others ...................................................................................................................................... 168
13.1 Configuring General Settings ...................................................................................................... 169
13.2 Configuring DST Settings ........................................................................................................... 170
13.3 Configuring More Settings .......................................................................................................... 171
13.4 Managing User Accounts............................................................................................................. 172
13.4.1 Adding a User .................................................................................................................... 172
13.4.2 Deleting a User .................................................................................................................. 174
13.4.3 Editing a User .................................................................................................................... 174
13.5 Logging out/Shutting down/Rebooting Device ........................................................................... 176
Chapter 14 Appendix ................................................................................................................................. 177
Glossary ................................................................................................................................................. 178
Troubleshooting ..................................................................................................................................... 179
11
User Manual of Digital Video Recorder
Chapter 1 Introduction
12
User Manual of Digital Video Recorder
1.1 Front Panels
Figure 1. 1 Front Panel of DS-7204HFHI-SE &amp; DS-7200HFHI-SL
Figure 1. 2 Front Panel of DS-7208HFHI-SE
Table 1. 1 Description of Front Panel
No.
Name
POWER
1
STATUS
TX/RX
2
IR Receiver
3
USB Interfaces
Function Description
Power indicator turns yellow when the power switch on the real
panel is turned on.
Status indicator blinks red when data is being read from or written to
HDD.
TX/RX indictor blinks yellow when network connection is
functioning properly.
Receiver for IR remote
Universal Serial Bus (USB) ports for additional devices such as
USB mouse and USB Hard Disk Drive (HDD).
Figure 1. 3 Front Panel of DS-7200HFHI-ST
Table 1. 2 Description of Control Panel Buttons
No.
1
Name
Function Description
POWER
Power indicator turns yellow once the power switch turns on.
READY
Ready indicator turns yellow when system is running.
STATUS
Status indicator turns red when SHIFT mode is on.
ALARM
Alarm indicator turns red when a sensor alarm is detected.
HDD
TX/RX
HDD indicator blinks red when data is being read from or written
to HDD.
TX/RX indictor blinks yellow when network connection is
functioning properly.
13
User Manual of Digital Video Recorder
No.
Name
Function Description
2
IR Receiver
Receiver for IR remote.
3
USB Interface
Universal Serial Bus (USB) ports for additional devices such as
USB mouse and USB Hard Disk Drive (HDD).
Switch between the numeric or letter input and functions of the
SHIFT
composite keys. (Input letter or numbers when the light is out;
Realize functions when the light is red.)
1/MENU
Enter numeral “1”;
Access the main menu interface.
Enter numeral “2”;
Enter letters “ABC”;
2/ABC/F1
The F1 button when used in a list field will select all items in the
list.
In PTZ Control mode, it will turn on/off PTZ light and when the
image is zoomed in, the key is used to zoom out.
Enter numeral “3”;
3/DEF/F2
Enter letters “DEF”;
The F2 button is used to change the tab pages.
In PTZ control mode, it zooms in the image.
Enter numeral “4”;
4/GHI/ESC
Enter letters “GHI”;
Exit and back to the previous menu.
4
Composite
Enter numeral “5”;
Keys
Enter letters “JKL”;
5/JKL/EDIT
Delete characters before cursor;
Check the checkbox and select the ON/OFF switch;
Start/stop record clipping in playback.
Enter numeral “6”;
6/MNO/PLAY
Enter letters “MNO”;
Playback, for direct access to all-day playback interface.
Enter numeral “7”;
7/PQRS/REC
Enter letters “PQRS”;
Open the manual record interface.
Enter numeral “8”;
8/TUV/PTZ
Enter letters “TUV”;
Access PTZ control interface.
Enter numeral “9”;
9/WXYZ/PREV
Enter letters “WXYZ”;
Multi-channel display in live view.
Enter numeral “0”;
0/A
Shift the input methods in the editing text field.(Upper and
lowercase, alphabet, symbols or numeric input).
The DIRECTION buttons are used to navigate between different
fields and items in menus.
5
DIRECTION
In the Playback mode, the Up and Down button is used to speed up
and slow down recorded video. The Left and Right button will
select the next and previous record files.
14
User Manual of Digital Video Recorder
No.
Name
Function Description
In Live View mode, these buttons can be used to cycle through
channels.
In PTZ control mode, it can control the movement of the PTZ
camera.
The ENTER button is used to confirm selection in any of the menu
modes.
It can also be used to tick checkbox fields.
ENTER
In Playback mode, it can be used to play or pause the video.
In single-frame Playback mode, pressing the button will advance
the video by a single frame.
In Auto-switch mode, it can be used to stop /start auto switch.
Figure 1. 4 Front Panel of DS-7300HFHI-ST
Table 1. 3 Description of Front Panel
No.
Name
POWER
READY
STATUS
1
ALARM
TX/RX
3
DVD-R/W
Composite
Keys
Ready indicator is normally green, indicating that the DVR is
functioning properly.
Indicator turns green when DVR is controlled by an IR remote
control with the address from 1~254;
Indicator turns red when the SHIFT button is used;
Indicator does not light when the DVR is controlled by a keyboard
or by the IR remote control with the address of 255;
Indicator turns green when the DVR is controlled by IR remote
control (with the address from 1~254) and keyboard at the same
time , and the SHIFT button is not used;
Indicator turns orange : (a) when the DVR is controlled by IR
remote control (with the address from 1~254) and keyboard at the
same time and the SHIFT button is used as well; (b) when the DVR
is controlled by IR remote control (with the address from 1~254)
and the SHIFT button is used.
Alarm indicator turns red when a sensor alarm is detected.
HDD indicator blinks in red when data is being read from or
written to HDD.
TX/RX indictor blinks in green when network connection is
functioning properly.
HDD
2
Function Description
Power indicator lights in green when DVR is powered up.
Slot for DVD-R/W.
Switch between the numeric or letter input and functions of the
SHIFT
composite keys. (Input letter or numbers when the light is out;
Realize functions when the light is red.)
15
User Manual of Digital Video Recorder
No.
Name
Function Description
1/MENU
Enter numeral “1”;
Access the main menu interface.
Enter numeral “2”;
Enter letters “ABC”;
The F1 button when used in a list field will select all items in the
2/ABC/F1
list.
In PTZ Control mode, it will turn on/off PTZ light and when the
image is zoomed in, the key is used to zoom out.
In live view or playback mode, the F1 button can be used to switch
between main and spot video output.
Enter numeral “3”;
3/DEF/F2
Enter letters “DEF”;
The F2 button is used to change the tab pages.
In PTZ control mode, it zooms in the image.
Enter numeral “4”;
4/GHI/ESC
Enter letters “GHI”;
Exit and back to the previous menu.
Enter numeral “5”;
Enter letters “JKL”;
5/JKL/EDIT
Delete characters before cursor;
Check the checkbox and select the ON/OFF switch;
Start/stop record clipping in playback.
Enter numeral “6”;
6/MNO/PLAY
Enter letters “MNO”;
In Playback mode, it is used for direct access to playback interface.
Enter numeral “7”;
7/PQRS/REC
Enter letters “PQRS”;
Manual record, for direct access to manual record interface;
manually enable/disable record.
Enter numeral “8”;
8/TUV/PTZ
Enter letters “TUV”;
Access PTZ control interface.
Enter numeral “9”;
9/WXYZ/PREV
Enter letters “WXYZ”;
Multi-channel display in live view.
Enter numeral “0”;
0/A
Shift the input methods in the editing text field. (Upper and
lowercase, alphabet, symbols or numeric input).
The DIRECTION buttons are used to navigate between different
fields and items in menus.
In the Playback mode, the Up and Down button is used to speed up
and slow down recorded video. The Left and Right button will
4
DIRECTION
select the next and previous record files.
In Live View mode, these buttons can be used to cycle through
channels.
In PTZ control mode, it can control the movement of the PTZ
camera.
16
User Manual of Digital Video Recorder
No.
Name
Function Description
The ENTER button is used to confirm selection in any of the menu
modes.
It can also be used to tick checkbox fields.
ENTER
In Playback mode, it can be used to play or pause the video.
In single-frame Playback mode, pressing the button will advance
the video by a single frame.
In Auto-switch mode, it can be used to stop /start auto switch.
Move the active selection in a menu. It will move the selection up
and down.
In Live View mode, it can be used to cycle through different
5
JOG SHUTTLE Control
channels.
In
the Playback
mode,
it
can
be used
to
jump
30s
forward/backward in video files.
In PTZ control mode, it can control the movement of the PTZ
camera.
Power on/off switch.
6
POWER
7
USB Interface
8
IR Receiver
Universal Serial Bus (USB) ports for additional devices such as
USB mouse and USB Hard Disk Drive (HDD).
Receiver for IR remote control.
Figure 1. 5 Front Panel of DS-8100HFHI-ST
Table 1. 4 Description of Front Panel
No.
Name
ALARM
READY
STATUS
1
Status
Indicators
HDD
TX/RX
GUARD
Function Description
Alarm indicator turns red when a sensor alarm is detected.
Ready indicator is normally blue, indicating that the DVR is
functioning properly.
Indicator turns blue when DVR is controlled by an IR remote.
Indicator turns red when controlled by a keyboard and orange when
IR remote and keyboard is used at the same time.
Indicator does not light when the DVR is controlled by the IR remote
control with the address of 255.
HDD indicator blinks in red when data is being read from or written
to HDD.
TX/RX indictor blinks in blue when network connection is
functioning properly.
Indicator turns blue when the device is armed;
Indicator does not light when the device is disarmed;
The arm/disarm state can be initiated by pressing and holding on the
ESC button for more than 3 seconds in live view mode.
17
User Manual of Digital Video Recorder
No.
Name
Function Description
Switch to the corresponding channel in Live view or PTZ Control
mode.
Input numbers and characters in Edit mode.
2
Alphanumeric Buttons
Switch between different channels in Playback mode.
The light of the button is blue when the corresponding channel is
recording; it is red when the channel is in network transmission
status; it is pink when the channel is recording and transmitting.
The DIRECTION buttons are used to navigate between different
fields and items in menus.
In the Playback mode, the Up and Down button is used to speed up
and slow down recorded video. The Left and Right button will select
DIRECTION
the next and previous record files.
In Live View mode, these buttons can be used to cycle through
channels.
3
Control
In PTZ control mode, it can control the movement of the PTZ
Buttons
camera.
The ENTER button is used to confirm selection in any of the menu
modes.
It can also be used to tick checkbox fields.
ENTER
In Playback mode, it can be used to play or pause the video.
In single-frame Playback mode, pressing the button will advance the
video by a single frame.
In Auto-switch mode, it can be used to stop /start auto switch.
Move the active selection in a menu. It will move the selection up
and down.
In Live View mode, it can be used to cycle through different
channels.
4
JOG SHUTTLE Control
In the Playback mode: the outer ring is used to speed up or slow
down the record files and the inner ring is used to jump 30s
forward/backward in records files.
In PTZ control mode, it can control the movement of the PTZ
camera.
5
POWER
Power on/off switch.
6
USB Interfaces
ESC
Universal Serial Bus (USB) ports for additional devices such as USB
mouse and USB Hard Disk Drive (HDD).
Exit and back to the previous menu.
Arm/disarm the DVR in live view mode.
Enter the Manual Record setting menu.
7
Composite
REC/SHOT
Keys
In PTZ control settings, press the button and then you can call a PTZ
preset by pressing Numeric button.
It is also used to turn audio on/off in the Playback mode.
Enter the Playback menu;
PLAY/AUTO
ZOOM+
A/FOCUS+
Auto scan in the PTZ Control mode.
Zoom in the PTZ camera in the PTZ Control setting.
Adjust focus in the PTZ Control menu.
18
User Manual of Digital Video Recorder
No.
Name
Function Description
It is also used to switch between input methods (upper and lowercase
alphabet, symbols and numeric input).
Edit text fields. When editing text fields, it will also function as a
Backspace button to delete the character in front of the cursor.
EDIT/IRIS+
On checkbox fields, pressing the button will tick the checkbox.
In PTZ Control mode, the button adjusts the iris of the camera.
In Playback mode, it can be used to generate video clips for backup.
Enter/exit the folder of USB device and eSATA HDD.
MAIN/SPOT/Z
OOM-
Switch between main and spot output.
In PTZ Control mode, it can be used to zoom out the image.
Select all items on the list when used in a list field.
F1/ LIGHT
In PTZ Control mode, it will turn on/off PTZ light (if applicable).
In Playback mode, it is used to switch between play and reverse play.
F2/ AUX
Cycle through tab pages.
In synchronous playback mode, it is used to switch between channels.
Press the button will help you return to the Main menu (after
successful login).
Press and hold the button for 5 seconds will turn off audible key
MENU/WIPER
beep.
In PTZ Control mode, the MENU/WIPER button will start wiper (if
applicable).
In Playback mode, it is used to show/hide the control interface.
Switch between single screen and multi-screen mode.
PREV/FOCUS-
In PTZ Control mode, it is used to adjust the focus in conjunction
with the A/FOCUS+ button.
Enter the PTZ Control mode.
PTZ/IRIS-
In the PTZ Control mode, it is used to adjust the iris of the PTZ
camera.
8
IR Receiver
Receiver for IR remote control.
9
DVD-R/W
Slot for DVD-R/W.
19
User Manual of Digital Video Recorder
1.2 IR Remote Control Operations
The DVR may also be controlled with the included IR remote control, shown in Figure 1. 6.
Batteries (2&times;AAA) must be installed before operation.
Figure 1. 6 Remote Control
The keys on the remote control closely resemble the ones found on the front panel. Refer to Table 1. 5, they
include:
Table 1. 5 Description of the IR Remote Control Buttons
No.
Name
Description
1
POWER
Power on/off the device.
2
DEV
Enables/Disables Remote Control.
20
User Manual of Digital Video Recorder
No.
Name
Description
3
Alphanumeric Buttons
Same as Alphanumeric buttons on front panel.
4
EDIT Button
Same as EDIT/IRIS+ button on front panel.
5
A Button
Same as A/FOCUS+ button on front panel.
6
REC Button
Same as REC/SHOT button on front panel.
7
PLAY Button
Same as the PLAY/AUTO button on front panel.
8
INFO Button
Same as the ZOOM+ button on front panel.
9
VOIP/MON Button
Same as the MAIN/SPOT/ZOOM- button on front panel.
10
MENU Button
Same as the MENU/WIPER button on front panel.
11
PREV Button
Same as the PREV/FOCUS- button on front panel.
12
DIRECTION/ENTER
Same as the DIRECTION/ENTER buttons on front panel.
Buttons
13
PTZ Button
Same as the PTZ/IRIS- button on front panel.
14
ESC Button
Same as the ESC button on front panel.
15
RESERVED
Reserved for future usage.
16
F1 Button
Same as the F1/LIGHT button on front panel.
17
PTZ Control Buttons
Buttons to adjust the iris, focus and zoom of a PTZ camera.
18
F2 Button
Same as the F2/AUX button on front panel.
Troubleshooting Remote Control:
Note: Make sure you have install batteries properly in the remote control. And you have to aim the remote
control at the IR receiver in the front panel.
If there is no response after you press any button on the remote, follow the procedure below to troubleshoot.
Steps:
1.
Go into Menu &gt; Settings &gt; General &gt; More Settings by operating the front control panel or the mouse.
2.
Check and remember DVR ID#. The default ID# is 255. This ID# is valid for all IR remote controls.
3.
Press the DEV button on the remote control.
4.
Enter the DVR ID# in step 2.
5.
Press the ENTER button on the remote.
If the Status indicator on the front panel turns blue, the remote control is operating properly. If the Status
indicator does not turn blue and there is still no response from the remote, please check the following:
1. Batteries are installed correctly and the polarities of the batteries are not reversed.
2. Batteries are fresh and not out of charge.
3. IR receiver is not obstructed.
If the remote still cannot function properly, please change the remote and try again, or contact the device
provider.
21
User Manual of Digital Video Recorder
1.3 USB Mouse Operation
A regular 3-button (Left/Right/Scroll-wheel) USB mouse can also be used with this DVR. To use a USB mouse:
1. Plug USB mouse into one of the USB interfaces on the front panel of the DVR.
2. The mouse should automatically be detected. If in a rare case that the mouse is not detected, the possible
reason may be that the two devices are not compatible, please refer to the recommended the device list
from your provider.
The operation of the mouse:
Table 1. 6 Description of the Mouse Control
Name
Action
Description
Single-Click
Live view: Select channel and show the quick set menu.
Menu: Select and enter.
Left-Click
Double-Click
Live view: Switch between single-screen and multi-screen.
Click and Drag
PTZ control: Wheeling.
Privacy mask and motion detection: Select target area.
Digital zoom-in: Drag and select target area.
Live view: Drag channel/time bar.
Right-Click
Single-Click
Live view: Show menu.
Menu: Exit current menu to upper level menu.
Scroll-Wheel
Scrolling up
Live view: Previous screen.
Menu: Previous item.
Scrolling down
Live view: Next screen.
Menu: Next item.
22
User Manual of Digital Video Recorder
1.4 Input Method Description
Figure 1. 7 Soft Keyboard
Description of the buttons on the soft keyboard:
Table 1. 7 Description of the Soft Keyboard Icons
Icons
Description
English
Numbers
Lowercase/Uppercase
Space
Exit
Icons
23
Description
Capital English
Symbols
Backspace
Enter
User Manual of Digital Video Recorder
1.5 Rear Panel
Figure 1. 8 DS-7204HFHI-SL
Figure 1. 9 DS-7208HFHI-SL
Figure 1. 10 DS-7204HFHI-SE
Figure 1. 11 DS-7204HFHI-ST
Figure 1. 12 DS-7208HFHI-SE and DS-7208HFHI-ST
No.
Item
Description
1
VIDEO IN
HD-SDI interface for video input.
2
AUDIO IN
RCA connector
3
AUDIO OUT
RCA connector
4
VGA
DB15 connector for VGA output. Display local video output and menu.
24
User Manual of Digital Video Recorder
No.
Item
Description
5
HDMI
HDMI video output connector.
6
USB Port
Universal Serial Bus (USB) port for additional devices.
7
Network Interface
Connector for network
8
RS-485 Interface
Connector for RS-485 devices.
9
Power Supply
DC 12V power supply.
10
Power Switch
Switch for turning on/off the device.
11
GND
Ground
Figure 1. 13 DS-7300HFHI-ST
Figure 1. 14 DS-8100HFHI-ST
No.
Item
Description
1
VIDEO IN
HD-SDI interface for video input.
2
VIDEO OUT
BNC connector for video output.
3
AUDIO IN
RCA connector
4
USB Port
Universal Serial Bus (USB) port for additional devices.
5
HDMI
HDMI video output connector.
6
VGA
DB15 connector for VGA output. Display local video output and menu.
7
AUDIO OUT
RCA connector
8
Network Interface
Connector for network
Connector for RS-485 devices. T+ and T- pins connect to R+ and Rpins of PTZ receiver respectively.
D+, D- pin connects to Ta, Tb pin of controller. For cascading devices,
9
RS-485 Interface
the first DVR’s D+, D- pin should be connected with the D+, D- pin of
the next DVR.
Connector for alarm input.
Connector for alarm output.
10
Power Supply
AC 100 ~ 240V power supply.
11
Power Switch
Switch for turning on/off the device.
25
User Manual of Digital Video Recorder
No.
Item
Description
12
GND
Ground
13
LINE IN
BNC connector for audio input.
14
eSATA
Connects external SATA HDD, CD/DVD-RW.
15
RS-232 Interface
Connector for RS-232 devices.
16
Termination Switch
RS-485 termination switch.
Up position is not terminated.
Down position is terminated with 120Ω resistance.
26
User Manual of Digital Video Recorder
Chapter 2 Getting Started
27
User Manual of Digital Video Recorder
2.1 Starting Up and Shutting Down the DVR
Purpose:
Proper startup and shutdown procedures are crucial to expanding the life of the DVR.
Before you start:
Check that the voltage of the extra power supply is the same with the DVR’s requirement, and the ground
connection is working properly.
Starting up the DVR
Steps:
1. Check the power supply is plugged into an electrical outlet. It is HIGHLY recommended that an
Uninterruptible Power Supply (UPS) be used in conjunction with the device.
2. Turn on the power switch on the rear panel, and the Power indicator LED should turn on indicating that
the unit begins to start up.
3. After startup, the Power indicator LED remains on.
Shutting down the DVR
Steps:
There are two proper ways to shut down the DVR. To shut down the DVR:
 OPTION 1: Standard shutdown
1. Enter the Shutdown menu.
Menu &gt; Shutdown
Figure 2. 1 Shutdown Menu
2. Select the Shutdown button.
3. Click the Yes button.
4. Turn off the power switch on the rear panel when the note appears (for DS-7200HFHI-SE and
DS-7200HFHI-SL series only).
Figure 2. 2 Shutdown Tips
 OPTION 2: By operating the front panel (for DS-7300HFHI-ST and DS-8100HFHI-ST series)
28
User Manual of Digital Video Recorder
1. Press and hold the POWER button on the front panel for 3 seconds.
2. Enter the administrator’s username and password in the dialog box for authentication.
3. Click the Yes button.
 Do not press the POWER button again when the system is shutting down.
 The device (exclude DS-7200HFHI-SL&amp;SE) remains standby mode after shutting down, and the
POWER indicator turns red; you can turn on the device by pressing the POWER button on the remote
control.
Rebooting the DVR
While in the Shutdown menu (Figure 2. 1), you can also reboot the DVR.
Steps:
1. Enter the Shutdown menu by clicking Menu &gt; Shutdown.
2. Click the Logout button to log out or the Reboot button to reboot the DVR.
29
User Manual of Digital Video Recorder
2.2 Using the Wizard for Basic Configuration
By default, the Setup Wizard will start once the DVR has loaded, as shown in Figure 2. 3.
Steps:
1. Please select the system language in the drop-down list on your demand.
Figure 2. 3 Resolution Selection
2. The Setup Wizard can walk you through some important settings of the DVR. If you do not want to use
the Setup Wizard at this time, click the Cancel button. You can also choose to use the Setup Wizard next
time by leaving the “Start wizard when DVR starts?” checkbox in checked status.
Figure 2. 4 Start Wizard Interface
3. Click Next button on the Wizard window to enter the Login window, as shown in Figure 2. 5.
30
User Manual of Digital Video Recorder
Figure 2. 5 Login Window
4. Enter the admin password. By default, the password is 12345.
5. To change the admin password, check the New Admin Password checkbox. Enter the new password and
confirm the password in the given fields.
6. Click the Next button to enter the date and time settings window, as shown in Figure 2. 6.
Figure 2. 6 Date and Time Settings
7. After the time settings, click Next button which will take you back to the Network Setup Wizard window,
as shown in Figure 2. 7.
DS-7204HFHI-SL
31
User Manual of Digital Video Recorder
DS-8100HFHI-ST
Other Models
Figure 2. 7 Network Configuration
8. Click Next button after you having configured the network parameters, which will take you to the HDD
Management window, shown in Figure 2. 8.
Figure 2. 8 HDD Management
9. To initialize the HDD, click the Init button. Initialization will remove all the data saved in the HDD.
10. Click Next button to enter the Record Settings window, as shown in Figure 2. 9.
32
User Manual of Digital Video Recorder
Figure 2. 9 Record Settings
11. Click Copy to copy the recording setting to other cameras.
12. Click OK to save the settings and exit the wizard.
33
User Manual of Digital Video Recorder
Chapter 3 Live View
34
User Manual of Digital Video Recorder
3.1 Introduction of Live View
Live view shows you the video image getting from each camera in real time. The DVR will automatically enter
Live View mode when powered on. It is also at the very top of the menu hierarchy, thus hitting the ESC many
times (depending on which menu you’re on) will bring you to the Live View mode.
Live View Icons
In the live view mode, there are icons at the right top of the screen for each channel, showing the status of the
record and alarm in the channel, so that you can know whether the channel is recorded, or whether there are
alarms occur as soon as possible.
Table 3. 1 Description of Live View Icons
Icons
Description
Alarm (video loss, tampering, motion detection or sensor alarm)
Record (manual record, schedule record, motion detection or alarm triggered record)
Alarm &amp; Record
35
User Manual of Digital Video Recorder
3.2 Operations in Live View Mode
In live view mode, there are many functions provided. The functions are listed below.
• Single Screen: show only one screen on the monitor.
• Multi-screen: show multiple screens on the monitor simultaneously.
• Auto-switch: the screen is auto switched to the next one. And you must set the dwell time for each screen
on the configuration menu before enabling the auto-switch. Menu&gt;Configuration&gt;Live View&gt;Dwell
Time.
•
•
•
•
Start Recording: normal record and motion detection record are supported.
Quick Set: select the output mode to Standard, Bright, Gentle or Vivid.
Playback: play back the recorded videos for current day.
Aux/Main output switch: the DVR checks the connection of the output interfaces to define the main and
auxiliary output interfaces. The priority level for the main and aux output is HDMI&gt;VGA&gt;CVBS. This
means if the HDMI is used, it will be the main output. If the HDMI is not used, the VGA output will be
the main output. See the table below.
Table 3. 2 Priorities of Interfaces
HDMI
VGA
CVBS
Main output
Auxiliary
output
1
√
√
√
HDMI
VGA
2
√
&times;
√
HDMI
CVBS
3
&times;
√
√
VGA
CVBS
4
&times;
&times;
√
CVBS

√ means the interface is in use, &times; means the interface is out of use or the connection is invalid. And the
HDMI, VGA and CVBScan be used at the same time.
When the aux output is enabled, the main output cannot do any operation, and you can do some basic operation
on the live view mode for the Aux output.
3.2.1 Front Panel Operation
This function is not supported by DS-7200HFHI-SL and DS-7200HFHI-SE series.
Table 3. 3 Front Panel Operation in Live View
Functions
Front Panel Operation
Show single screen
Press the corresponding Alphanumeric button. E.g. Press 2 to display only the
screen for channel 2.
Show multi-screen
Press the PREV button.
Manually switch
Next screen: right direction button.
screens
Previous screen: left direction button.
Auto-switch
Press Enter button.
Playback
Press Play button.
36
User Manual of Digital Video Recorder
3.2.2 Using the Mouse in Live View
Table 3. 4 Mouse Operation in Live View
Name
Description
Menu
Enter the main menu of the system by right clicking the mouse.
Single Screen
Switch to the single full screen by choosing channel number from the dropdown
list.
Multi-screen
Adjust the screen layout by choosing from the dropdown list.
Previous Screen
Switch to the previous screen.
Next Screen
Switch to the next screen.
Start/Stop
Enable/disable the auto-switch of the screens.
Auto-switch
The dwell time of the live view configuration must be set before using
Start Auto-switch.
Start Recording
Start recording of all channels, Normal Record and Motion Detection Recording
are selectable from the dropdown list.
Quick Set
Output Mode is configurable with Standard, Bright, Gentle and Vivid options.
Playback
Enter the playback interface and start playing back the video of the selected
channel immediately.
Aux Monitor
Switch to the auxiliary output mode and the operation for the main output is
disabled.
If you enter Aux monitor mode and the Aux monitor is not connected, the
mouse operation is disabled; you need to switch back to the Main output
with the F1 button on front panel or VOIP/MON button on IR remote
control and then press the Enter button.
If the corresponding camera supports intelligent function, the Reboot Intelligence option will be
included when right-clicking mouse on this camera.
37
User Manual of Digital Video Recorder
DS-7200HFHI-SL&amp;SE&amp;ST
DS-7300HFHI-ST &amp; DS-8100HFHI-ST
Figure 3. 1 Right-click Menu
3.2.3 Using an Auxiliary Monitor
Certain features of the Live View are also available while in an Aux monitor. These features include:
• Single Screen: Switch to a full screen display of the selected camera. Camera can be selected from a
dropdown list.
• Multi-screen: Switch between different display layout options. Layout options can be selected from a
dropdown list.
• Previous Screen: When displaying less than the maximum number of cameras in Live View, clicking this
feature will switch to the previous set of displays.
• Next Screen: When displaying less than the maximum number of cameras in Live View, clicking this
feature will switch to the next set of displays.
• Quick Set: Set the video output mode to Standard, Bright, Gentle or Vivid.
• Menu Output Mode: Select the menu output mode to HDMI/VGA, Main CVBS or Auto.
• Main Monitor: Enter Main operation mode.
In the live view mode of the main output monitor, the menu operation is not available while Aux output
mode is enabled.
3.2.4 Main/Aux Output Switching
When the HDMI/VGA output is configured as the main output, you can perform the following operation to
switch to CVBS output as the main output.
Steps:
1. Use the mouse wheel to double-click on the HDMI/VGA output screen, and the following message box
pops up:
38
User Manual of Digital Video Recorder
Figure 3. 2 Switch Main and Aux Output
2. Use the mouse wheel to double-click on the screen again to switch to the Aux output, or click Cancel to
cancel the operation.
3. Select the Menu Output Mode to Main CVBS from the right-click menu on the CVBS output monitor.
Figure 3. 3 Right-click Menu on CVBS Output Monitor
4. On the pop-up message box, click Yes to restart the device to enable the CVBS output as the main output.
You can select the Menu Output Mode under Menu&gt;Configuration&gt;More Settings to Auto or
HDMI/VGA and then restart the device to switch the main output back to HDMI/VGA output.
3.2.5 Quick Setting Toolbar in Live View Mode
On the screen of each channel, there is a quick setting toolbar which shows when you point the mouse to the
bottom of the screen.
Figure 3. 4 Quick Setting Toolbar
Table 3. 5 Description of Quick Setting Toolbar Icons
Icons
Description
Enable/Disable
/
Manual Record
Icons
Description
Instant Playback
Close Live View
PTZ Control
Icons
/
Description
Mute/Audio on
Digital Zoom
Instant Playback only shows the record in last five minutes. If no record is found, it means there is no
39
User Manual of Digital Video Recorder
record during the last five minutes.
Digital Zoom can zoom in the selected area to the full screen. Click and draw to select the area to zoom in,
as shown in Figure 3. 5.
Figure 3. 5 Digital Zoom
40
User Manual of Digital Video Recorder
3.3 Channel-zero Encoding
This chapter is only applicable to DS-7300HFHI-ST and DS-8100HFHI-ST.
Purpose:
Sometimes you need to get a remote view of many channels in real time from web browser or CMS(Client
Management System) software, in order to decrease the bandwidth requirement without affecting the image
quality, channel-zero encoding is supported as an option for you.
Steps:
1. Enter the Live View Settings interface.
Menu&gt; Configuration&gt; Live View
2. Select the Channel-Zero Encoding tab.
Figure 3. 6 Live View- Channel-Zero Encoding
3. Check the checkbox after Enable Channel-Zero Encoding.
4. Configure the Frame Rate, Max. Bitrate Mode and Max. Bitrate.
5. Click the Apply button to activate the settings.
After you set the Channel-Zero encoding, you can get a view in the remote client or web browser of 16
channels in one screen.
41
User Manual of Digital Video Recorder
3.4 Adjusting Live View Settings
Purpose:
Live View settings can be customized according to different needs. You can configure the output interface,
dwell time for screen to be shown, mute or turning on the audio, the screen number for each channel, etc.
Steps:
1. Enter the Live View Settings interface.
Menu&gt; Configuration&gt; Live View
Figure 3. 7 Live View-General
The settings available in this menu include:
• Video Output Interface: Designates the output to configure the settings for. Outputs include HDMI
(depends on the model) and VGA.
• Live View Mode: Designates the display mode to be used for Live View.
• Dwell Time: The time in seconds to dwell between switching of channels when enabling auto-switch
in Live View.
• Enable Audio Output: Enables/disables audio output for the selected video output.
• Event Output: Designates the output to show event video.
• Full Screen Monitoring Dwell Time: The time in seconds to show alarm event screen.
2. Set the camera order.
Figure 3. 8 Live View- Camera Order
1) Select View tab.
2) Click a window to select it, and then double-click a camera name in the camera list you would like to
display. Setting an ‘X’ means the window will not display any channel.
3) Click the Apply button.
42
User Manual of Digital Video Recorder
3.5 User Logout
Purpose:
After logging out, the monitor turns to the live view mode and if you want to do some operation, you need to
enter user name and password to log in again.
Steps:
1. Enter the Shutdown menu.
Menu&gt;Shutdown
Figure 3. 9 Shutdown
2. Click Logout.
After you have logged out the system, menu operation on the screen is invalid. It is required a user
name and password to login the system.
43
User Manual of Digital Video Recorder
Chapter 4 PTZ Controls
44
User Manual of Digital Video Recorder
4.1 Configuring PTZ Settings
Purpose:
Follow the procedure to set the parameters for PTZ. The configuring of the PTZ parameters should be done
before you set the PTZ camera.
Before you start:
Check that the PTZ and the DVR are connected properly through RS-485 interface.
Steps:
1. Enter the PTZ Settings interface.
Menu &gt;Camera&gt; PTZ
Figure 4. 1 PTZ- General
2. Choose the camera for PTZ setting next to Camera label.
3. Enter the parameters of the PTZ camera.
All the parameters should be exactly the same as the PTZ camera parameters.
4. Click Copy if you want to configure same settings to other PTZ cameras.
5. Click Apply button to save and exit menu.
45
User Manual of Digital Video Recorder
4.2 Setting PTZ Presets, Patrols &amp; Patterns
Before you start:
Please make sure that the presets, patrols and patterns should be supported by PTZ protocols.
4.2.1 Customizing Presets
Purpose:
Follow the steps to set the Preset location which you want the PTZ camera to point to when an event takes
place.
Steps:
1. Enter the PTZ Control interface.
Menu&gt;Camera&gt;PTZ&gt;More Settings
Figure 4. 2 PTZ- More Settings
2. Use the directional button to wheel the camera to the location where you want to set preset.
3. Click the round icon before Save Preset.
4. Click the preset number to save the preset.
Repeat the steps2-4 to save more presets. If the number of the presets you want to save is greater than 17, you
can click […] and choose the available numbers.
Figure 4. 3 More Presets
46
User Manual of Digital Video Recorder
4.2.2 Calling Presets
Purpose:
This feature enables the camera to point to a specified position such as a window when an event takes place.
Call preset in the PTZ setting interface:
Steps:
1. Enter the PTZ Control interface.
Menu&gt;Camera&gt;PTZ&gt;More Settings
2. Check the round icon before Call Preset.
Figure 4. 4 PTZ- Call Preset
3. Choose the preset number.
Call preset in live view mode:
Steps:
1. Press the PTZ button on the front panel or click the PTZ Control icon
enter the PTZ setting menu in live view mode.
Figure 4. 5 PTZ Toolbar
2. Choose Camera in the list on the menu.
47
in the quick setting bar to
User Manual of Digital Video Recorder
3. Double-click the preset you want to call in the Preset list.
4.2.3 Customizing Patrols
Purpose:
Patrols can be set to move the PTZ to a set of different key points sequentially and have it stay there for a set
duration before moving on to the next key point. The key points are corresponding to the presets. The presets
can be set following the steps above in Customizing Presets.
Steps:
1. Enter the PTZ Control interface.
Menu&gt;Camera&gt;PTZ&gt;More Settings
2. Select patrol number.
3. Select the
under Patrol option box to add key points for the patrol.
Figure 4. 6 PTZ- Add Key Point
4. Configure key point parameters, such as the key point No., duration of staying for one key point and speed
of patrol. The key point is corresponding to the preset.
The Preset determines the order at which the PTZ will follow while cycling through the patrol.
The Duration refers to the time span to stay at the corresponding key point.
The Speed defines the speed at which the PTZ will move from one key point to the next.
Figure 4. 7 Key point Configuration
5. Click OK to save the key point to the patrol.
48
User Manual of Digital Video Recorder
Repeat the above steps to add more key points.
You can also click
to delete the corresponding key point and click
to delete all the key points.
Figure 4. 8 KeyPoints Deletion
4.2.4 Calling Patrols
Purpose:
Calling a patrol makes the PTZ to move according the predefined patrol path.
Calling patrol in the PTZ setting interface:
Steps:
1. In the PTZ setting interface.
Menu&gt; Camera&gt; PTZ&gt; More Settings
2. Select the patrol number, and then click
3. Click
to call the patrol.
to stop it.
Figure 4. 9 Calling Patrol
Calling patrol in live view mode:
Steps:
1. Press PTZ control on the front panel or on the remote, or click PTZ Control icon
49
on the quick setting
User Manual of Digital Video Recorder
toolbar, to show the PTZ control panel.
2. Choose Patrol on the control bar.
3. Double-click the patrol you want to call, or click to select the patrol and click
to call the patrol.
Figure 4. 10 PTZ Panel- Patrol
4.2.5 Customizing Patterns
Purpose:
Patterns can be set by recording the movement of the PTZ. You can call the pattern to make the PTZ movement
according to the predefined path.
Steps:
1. Enter the PTZ Control interface.
Menu&gt;Camera&gt;PTZ&gt;More Settings
2. Choose pattern number in the option box.
Figure 4. 11 PTZ- Pattern
3. Click
, and use your mouse to drag the image or click the eight directional buttons in the control box
under the image to move the PTZ camera.
The movement of the PTZ is recorded as the pattern.
50
User Manual of Digital Video Recorder
4. Click
to save the pattern.
Repeat the above steps to save more patterns.
4.2.6 Calling Patterns
Purpose:
Follow the procedure to move the PTZ camera according to the predefined patterns.
Calling pattern in the PTZ setting interface
Steps:
1. Enter the PTZ Control interface.
2. Select the pattern number.
3. Click
, then the PTZ moves according to the pattern. Click
to stop it.
Figure 4. 12 PTZ- Calling Pattern
Call pattern in live view mode.
Steps:
1. In the live view mode, press PTZ control on the front panel or on the remote control, or click PTZ Control
icon
on the quick setting toolbar.
2. And then choose Pattern on the control bar.
3. Double-click the pattern you want to call, or you can click to select the pattern and click
pattern.
Figure 4. 13 PTZ Panel- Pattern
51
to call the
User Manual of Digital Video Recorder
4.3 PTZ Control Panel
In the Live View mode, you can press the PTZ Control button on the front panel or on the remote control, or
choose the PTZ Control icon
to enter the PTZ panel.
Figure 4. 14 PTZ Panel
Table 4. 1 Description of the PTZ panel icons
Icon
Description
Icon
Description
Direction button and
Zoom+, Focus+,
the auto-cycle button
Iris+
Icon
Description
Zoom-, Focus-, Iris-
The speed of the
Light on/off
Wiper on/off
PTZ movement
Image
3D-Zoom
Preset
Centralization
Patrol
Pattern
Menu
Previous item
Next item
Start pattern/patrol
Stop the patrol or
Minimize
pattern movement
windows
Exit
52
User Manual of Digital Video Recorder
Chapter 5 Record Settings
53
User Manual of Digital Video Recorder
5.1 Configuring Encoding Parameters
Before you start:
1. Make sure that the HDD has already been installed. If not, please install a HDD and initialize it.
(Menu&gt;HDD&gt;General)
Figure 5. 1 HDD- General
2. Click Advance to check the storage mode of the HDD.
1) Whether the HDD mode is Quota, please set the maximum record capacity. For detailed information,
see Chapter 10.5 Configuring Quota Mode.
2) If the HDD mode is Group, you should set the HDD group. For detailed information, see Chapter 5.8
Configuring HDD Group for Recording.
Figure 5. 2 HDD- Advanced
Steps:
1. Enter the Record settings interface to configure the encoding parameters:
Menu&gt;Record&gt;Encoding
Figure 5. 3 Record Encoding
2. Set the encoding parameters for recording.
54
User Manual of Digital Video Recorder
1) Select the Record tab to configure.
2) Select a camera number in the camera dropdown list.
You can configure the stream type, the resolution, the video quality and other parameters on demand
for Main Stream(Normal) and Main Stream(Event) respectively.
The Input Resolution of camera connected will be displayed in the live view for 5 seconds when the
camera is connected, or the DVR is powered on. The input resolution includes the resolution and
frame rate of the camera, e.g. 1080P25.
3) You can configure the advantage parameters, including pre-record, post-record time, expired time,
redundant record (this option is only available when the HDD mode is Group) and whether you want
to record audio.
• Pre-record: The time you set to record before the scheduled time or event. For example, when an
alarm triggered the recording at 10:00, if you set the pre-record time as 5 seconds, the camera
records it at 9:59:55.
• Post-record: The time you set to record after the event or the scheduled time. For example, when
an alarm triggered the recording ends at 11:00, if you set the post-record time as 5 seconds, it
records till 11:00:05.
• Expired Time: The expired time is the longest time for a record file to be kept in the HDD, if the
deadline is reached, the file will be deleted. You can set the expired time to 0, and then the file will
not be deleted. The actual keeping time for the file should be determined by the capacity of the
HDD.
• Redundant Record: Enabling redundant record means you save the record in the redundant HDD.
See Chapter 5.7 Configuring Redundant Recording.
• Record Audio: Check the checkbox of Record Audio to record the sound, otherwise record the
image without sound.
4) Click Apply to save the settings.
5) You can copy the settings to other channels by clicking Copy, if the setting can also be used for other
channels.
Figure 5. 4 Copy Camera Settings
The redundant record is to decide whether you want the camera to save the record files in the
redundant HDD. You must configure the redundant HDD in HDD settings. For detailed information,
55
User Manual of Digital Video Recorder
see Chapter 10.4.2 Setting HDD Property.
3. Set encoding parameters for sub-stream.
1) Select the Substream tab.
Figure 5. 5 Sub-stream Encoding
2) Select a camera in the camera dropdown list.
3) Configure the parameters.
4) Click Apply to save the settings.
5) (Optional) If the parameters can also be used to other channels, click Copy to copy the settings to
other channels.
56
User Manual of Digital Video Recorder
5.2 Configuring Record Schedule
Purpose:
Set the record schedule, and then the camera will automatically start/stop recording according to the configured
schedule.
Steps:
1. Enter the Record Schedule interface.
Menu&gt; Record&gt; Schedule
DS-7200HFHI-SL&amp;SE&amp;ST
DS-7300HFHI-ST and DS-8100HFHI-ST
Figure 5. 6 Record Schedule
2. Choose the camera you want to configure in the Camera dropdown list.
3. Check the checkbox of Enable Schedule.
4. Configure the record schedule.
Edit the schedule
1)
2)
3)
Click Edit.
In the message box, you can choose the day to which you want to set schedule.
To schedule an all-day recording, check the checkbox after the All Day item.
57
User Manual of Digital Video Recorder
Figure 5. 7 Edit Schedule- All Day
4)
To arrange other schedule, leave the All Day checkbox blank and set the Start/End time.
Figure 5. 8 Edit Schedule- Set Time Period
Up to 8 periods can be configured for each day. And the time periods cannot be overlapped each
other.
Repeat the above steps 1)-3) to schedule recording for other days in the week. If the schedule can also be
set to other days, click Copy.
Figure 5. 9 Copy Schedule to Other Days
58
User Manual of Digital Video Recorder
The Holiday option is available when you enable holiday schedule in Holiday settings. See
Chapter 5.6 Configuring Holiday Record.
5)
Click OK to save setting and back to upper level menu.
Draw the schedule
1)
Click on the color icon to select a record type in the event list on the right-side of the interface.
Figure 5. 10 Draw the Schedule
Descriptions of the color icons are shown in the figure below.
Figure 5. 11 Descriptions of the color icons
2)
Click and drag the mouse on the schedule.
3)
Click on the other area except for the schedule table to finish and exit the drawing.
You can repeat step 4 to set schedule for other channels. If the settings can also be used to other channels,
click Copy, and then choose the channel to which you want to copy.
59
User Manual of Digital Video Recorder
Figure 5. 12 Copy Schedule to Other Channels
5. Click Apply in the Record Schedule interface to save the settings.
60
User Manual of Digital Video Recorder
5.3 Configuring Motion Detection Record
Purpose:
Follow the steps to set the motion detection parameters. In the live view mode, once a motion detection event
takes place, the DVR can analyze it and do many actions to handle it. Enabling motion detection function can
trigger certain channels to start recording, or trigger full screen monitoring, audio warning, notifying the
surveillance center, sending email and so on.
Steps:
1. Enter the Motion Detection interface.
Menu&gt;Camera&gt;Motion
Figure 5. 13 Motion Detection
2. Configure Motion Detection:
1) Choose camera you want to configure.
2) Check the checkbox after Enable Motion Detection.
3) Drag and draw the area for motion detection by mouse. If you want to set the motion detection for all
the area shot by the camera, click Full Screen. To clear the motion detection area, click Clear.
Figure 5. 14 Motion Detection- Mask
4) Click Handling, and the message box for channel information pops up.
61
User Manual of Digital Video Recorder
Figure 5. 15 Motion Detection Handling
5) Select the channels which you want the motion detection event to trigger recording.
6) Click Apply to save the settings.
7) Click OK to back to the upper level menu.
8) Exit the Motion Detection menu.
3. Configure the schedule.
Please refer to the step 4 of Chapter 5.2 Configuring Record Schedule, while you may choose Motion as
the record type.
62
User Manual of Digital Video Recorder
5.4 Configuring Alarm Triggered Record
The DS-7200HFHI-SL&amp;SE&amp;ST series DVR does not support the alarm input by default.
Purpose:
Follow the procedure to configure alarm triggered recording.
Steps:
1. Enter the Alarm setting interface.
Menu&gt; Configuration&gt; Alarm
Figure 5. 16 Alarm Settings
2. Click the Alarm Input tab.
Figure 5. 17 Alarm Settings- Alarm Input
1)
Select Alarm Input number and configure alarm parameters.
2)
Choose N.O (normally open) or N.C (normally closed) for alarm type.
3)
Check the checkbox of Setting.
4)
Click the
button.
63
User Manual of Digital Video Recorder
Figure 5. 18 Alarm Handling
5)
Choose the alarm triggered recording channel.
6)
Check the checkbox
7)
Click Apply to save settings.
8)
Click OK to back to the upper level menu.
to select channel.
Repeat the above steps to configure other alarm input parameters.
If the setting can also be applied to other alarm inputs, click Copy and choose the alarm input number.
Figure 5. 19 Copy Alarm Input
3. Configure the schedule.
Please refer to the step 4 of Chapter 5.2 Configuring Record Schedule, while you may choose Alarm as
the record type.
64
User Manual of Digital Video Recorder
5.5 Manual Record
Purpose:
Follow the steps to set parameters for the manual record. Using manual record, you don’t need to set a schedule
for recording.
Steps:
1. Enter the Manual settings interface.
Menu&gt; Manual
Figure 5. 20 Manual Record
2. Enable manual record.
Click the status icon
Or click the status icon
before camera number to change it to
.
of Analog to enable manual record of all channels.
3. Disable manual record.
Click the status icon
Or click the status icon
to change it to
.
of Analog to disable manual record of all channels.
After rebooting all the manual records enabled are canceled.
65
User Manual of Digital Video Recorder
5.6 Configuring Holiday Record
Purpose:
Follow the steps to configure the record schedule on holiday for that year. You may want to have different plan
for recording on holiday.
Steps:
1. Enter the Record setting interface.
Menu&gt;Record
2. Choose Holiday on the left bar.
Figure 5. 21 Holiday Settings
3. Enable Edit Holiday schedule.
1) Click
to enter the Edit interface.
Figure 5. 22 Edit Holiday Settings
2) Check the checkbox of Enable.
3) Select Mode from the dropdown list.
There are three different modes for the date format to configure holiday schedule. By Month, By Week,
and By Month are selectable.
4) Set the start and end date.
66
User Manual of Digital Video Recorder
5) Click Apply to save settings.
6) Click OK to exit the Edit interface.
4. Configure the record schedule.
Please refer to the Chapter 5.2 Configuring Record Schedule, while you may choose Holiday in the
Schedule dropdown list, or you can draw the schedule on the timeline of Holiday. See the two figures
below.
Figure 5. 23 Edit Schedule- Holiday
Figure 5. 24 Draw Schedule- Holiday
Up to 8 periods can be configured for each day. And the time periods cannot be overlapped each other.
In the time table of the channel, both holiday schedule and normal day schedule are displayed.
Repeat the above step 4 to set Holiday schedule for other channel. If the holiday schedule can also be used to
other channels, click Copy and choose the channel you want to apply the settings.
67
User Manual of Digital Video Recorder
5.7 Configuring Redundant Recording
Purpose:
Enabling redundant recording, which means saving the record files not only in the R/W HDD but also in the
redundant HDD, will effectively enhance the data safety and reliability.
Before you start:
You must set the Storage mode in the HDD advanced settings to Group before you set the HDD property to
Redundant. For detailed information, please refer to Chapter 10.4 Managing HDD Group. There should be at
least another HDD which is in Read/Write status.
Steps:
1. Enter HDD Information interface.
Menu&gt; HDD
Figure 5. 25 HDD General
2. Select the HDD and click
to enter the Local HDD Settings interface.
1) Set the HDD property to Redundant.
Figure 5. 26 HDD General-Editing
2) Click Apply to save the settings.
3) Click OK to back to the upper level menu.
3. Enter the Record setting interface.
Menu&gt; Record&gt; Encoding
1) Select the Record tab.
68
User Manual of Digital Video Recorder
Figure 5. 27 Encoding Record
2) Select Camera you want to configure.
3) Check the checkbox of Redundant Record.
4) Click Apply to save settings.
If the encoding parameters can also be used to other channels, click Copy and choose the channel you want to
apply the settings.
69
User Manual of Digital Video Recorder
5.8 Configuring HDD Group for Recording
Purpose:
You can group the HDDs and save the record files in certain HDD group.
Steps:
1. Enter HDD setting interface.
Menu&gt;HDD&gt;Advanced
Figure 5. 28 HDD General
2. Select Advanced on the left bar.
Check whether the storage mode of the HDD is Group. If not, set it to Group. For detailed information,
please refer to Chapter 10.4 Managing HDD Group.
3. Select General in the left bar.
Click
to enter editing interface.
4. Configuring HDD group.
1)
Choose a group number for the HDD group.
2)
Click Apply to save your settings.
3)
Click OK to back to the upper level menu.
Repeat the above steps to configure more HDD groups.
5. Choose the Channels which you want to save the record files in the HDD group.
1)
Select Advanced on the left bar.
Figure 5. 29 HDD Advanced
2)
Choose Group number in the dropdown list of Record on HDD Group
3)
Check the channels you want to save in this group.
4)
Click Apply to save settings.
After you have configured the HDD groups, you can configure the Recording settings following the
procedure provided in Chapter 5.2-5.7.
70
User Manual of Digital Video Recorder
5.9 Files Protection
Purpose:
You can lock the recorded files or set the HDD property to Read-only to protect the record files from being
overwritten.
Protect file by locking the record files
Steps:
1. Enter Playback setting interface.
Menu&gt; Export
Figure 5. 30 Export
2. Select the channels you want to investigate by checking the checkbox to
.
3. Configure the record type, file type, start time and end time.
4. Click Search to show the results.
Figure 5. 31 Export- Search Result
5. Protect the record files.
1) Find the record files you want to protect, and then click the
icon which will turn to
that the file is locked.
The record files of which the recording is still not completed cannot be locked.
2) Click
to change it to
to unlock the file and the file is not protected.
71
, indicating
User Manual of Digital Video Recorder
Figure 5. 32 Unlocking Attention
Protect file by setting HDD property to Read-only
Before you start:
To edit HDD property, you need to set the storage mode of the HDD to Group. See Chapter 10.4 Managing
HDD Group.
Steps:
1. Enter HDD setting interface.
Menu&gt; HDD
Figure 5. 33 HDD General
2. Click
to edit the HDD you want to protect.
Figure 5. 34 HDD General- Editing
3. Set the HDD to Read-only.
4. Click OK to save settings and back to the upper level menu.
 You cannot save any files in a Read-only HDD. If you want to save files in the HDD, change the
property to R/W.
 If there is only one HDD and is set to Read-only, the DVR cannot record any files. Only live view mode
is available.
 If you set the HDD to Read-only when the DVR is saving files in it, then the file will be saved in next
R/W HDD. If there is only one HDD, the recording will be stopped.
72
User Manual of Digital Video Recorder
Chapter 6 Playback
73
User Manual of Digital Video Recorder
6.1 Playing Back Record Files
6.1.1 Playing Back by Channel
Purpose:
Play back the recorded video files of a specific channel in the live view mode. Channel switch is supported.
 OPTION 1
Choose a channel in live view mode using the mouse and click the
button in the quick setting toolbar.
Only record files recorded during the last five minutes on this channel will be played back.
Figure 6. 1 Instant Playback Interface
 OPTION 2
Steps:
1. Enter the Playback interface.
Mouse: right click a channel in live view mode and select Playback from the menu, as shown in Figure 6.
2.
74
User Manual of Digital Video Recorder
DS-7200HFHI-SL&amp;SE&amp;ST
DS-7300HFHI-ST &amp; DS-8100HFHI-ST
Figure 6. 2 Right-click Menu under Live View
Front Panel: press PLAY button to play back record files of the channel under single-screen live view
mode.
Under multi-screen live view mode, the recorded files of the top-left channel will be played back.
For the DS-7300HFHI-ST and DS-8100HFHI-ST, pressing numerical buttons will switch playback
to the corresponding channels during playback process.
2. Playback management.
The toolbar in the bottom part of Playback interface can be used to control playing progress, as shown in
Figure 6. 3.
Figure 6. 3 Playback Interface
Click the channel(s) if you want to switch playback to another channel or execute simultaneous playback
of multiple channels.
75
User Manual of Digital Video Recorder
Figure 6. 4 Toolbar of Playback
Table 6. 1 Detailed Explanation of Playback Toolbar
Button
Operation
Button
Audio on/
/
Mute
tag
Pause reverse
Single-frame
reverse play
Add
Tag
customized tag
management
Button
Operation
30s reverse
Speed down
Scaling
Play/
/
Operation
30s forward
clipping
Pause play/
play/
Reverse play/
Button
Start/Stop
/
Add default
/
Operation
/
Single-frame
up/down the
Speed up
time line
play
Previous day
Next day
Full Screen
Exit
Stop
Digital Zoom
Smart Search
Video type
Process bar
Video type bar
Playback progress bar: use the mouse to drag the progress bar to locate special frames.
6.1.2 Playing Back by Time
Purpose:
Play back video files recorded in specified time duration. Multi-channel simultaneous playback and channel
switch are supported.
Steps:
1. Enter playback interface.
Menu&gt;Playback
2. Check the checkbox of channel(s) in the channel list and then double-click to select a date on the calendar.
Figure 6. 5 Playback Calendar
76
User Manual of Digital Video Recorder
If there are record files for that camera in that day, in the calendar, the icon for that day is displayed as
. Otherwise it is displayed as
In the Playback interface:
The toolbar in the bottom part of Playback interface can be used to control playing process, as shown in
Figure 6. 6.
Figure 6. 6 Interface of Playback by Time
Figure 6. 7 Toolbar of Playback by Time
Table 6. 2 Detailed Explanation of Playback Toolbar
Button
Operation
Button
Audio on/
/
Mute
tag
Pause reverse
Single-frame
reverse play
Add
Tag
customized tag
management
Button
Operation
30s reverse
Speed down
Scaling
Play/
/
Operation
30s forward
clipping
Pause play/
play/
Reverse play/
Button
Start/Stop
/
Add default
/
Operation
/
Single-frame
up/down the
Speed up
time line
play
Previous day
Next day
Full Screen
Exit
Stop
Digital Zoom
Smart Search
Video type
Process bar
Video type bar
77
User Manual of Digital Video Recorder
Playback progress bar: use the mouse to click any point of the progress bar or drag the progress bar to
locate special frames.
6.1.3 Playing Back by Event Search
Purpose:
Play back recording files on one or several channels searched out by restricting event type (e.g. alarm input and
motion detection).
Steps:
1. Enter the Playback interface.
Menu &gt; Playback
2. Select the Event in the drop-down list on the top-left side.
3. Select Alarm Input or Motion as the event type, edit the Start time and End time.
Figure 6. 8 Alarm Input Search Interface
78
User Manual of Digital Video Recorder
Figure 6. 9 Motion Search Interface
4. Click Search button to get the search result information. You may refer to the right-side bar for the result.
Figure 6. 10 Search Result Bar (Alarm In and Motion)
5. Click
button to play back the file.
You can click the Back button to back to the search interface.
Pre-play and post-play can be configured.
6. (Optional) If multiple channels are triggered recording by the alarm input, clicking the
button will
pop up a synchoronouse playback channel selection window. Select channel(s) you want to play and click
the OK button.
79
User Manual of Digital Video Recorder
7. Playback management.
The toolbar in the bottom part of Playback interface can be used to control playing process.
Figure 6. 11 Interface of Playback by Event
Figure 6. 12 Toolbar of Playback by Event
Table 6. 3 Detailed Explanation of Playback-by-event Toolbar
Button
Operation
Button
Audio on/
/
Mute
tag
Pause reverse
Single-frame
reverse play
Previous day
Operation
Button
30s forward
clipping
Add
Tag
customized tag
management
Operation
30s reverse
Speed down
Pause play/
play/
Reverse play/
Button
Start/Stop
/
Add default
/
Operation
Play/
/
Single-frame
Stop
Speed up
Full Screen
Exit
play
Next day
Scaling
Process bar
Video type
Digital Zoom
/
up/down the
time line
Smart Search
(Not supported)
Playback progress bar: use the mouse to click any point of the progress bar or drag the progress bar to
locate special frames.
80
User Manual of Digital Video Recorder
6.1.4 Playing Back by Tag
Purpose:
Video tag allows you to record related information like people and location of a certain time point during
playback. You are also allowed to use video tag(s) to search for record files and position time point.
Before playing back by tag:
1. Enter Playback interface.
Menu&gt;Playback
2. Search and play back the record file(s). Refer to Chapter 6.1.1 Playing Back by Channel for the detailed
information about searching and playback of the record files.
Figure 6. 13 Interface of Playback by Time
Click
button to add default tag.
Click
button to add customized tag and input tag name.
Max. 64 tags can be added to a single video file.
3. Tag management.
Click
button to check, edit and delete tag(s).
Figure 6. 14 Tag Management Interface
81
User Manual of Digital Video Recorder
Steps:
1. Select the Tag from the drop-down list in the Playback interface.
2. Choose channels, edit start time and end time, and then click Search to enter Search Result interface.
You can enter keyword in the textbox
to search the tag on your command.
Figure 6. 15 Video Search by Tag
3. Click
button to play back the file.
You can click the Back button to back to the search interface.
Pre-play and post-play can be configured.
Figure 6. 16 Interface of Playback by Tag
82
User Manual of Digital Video Recorder
Figure 6. 17 Toolbar of Playback by Tag
Table 6. 4 Detailed Explanation of Playback-by-tag Toolbar
Button
Operation
Button
Audio on/
/
Mute
Operation
Start/Stop
/
tag
Pause reverse
Button
Add
Tag
customized tag
management
Operation
30s reverse
Speed down
Pause play/
play/
Reverse play/
Operation
30s forward
clipping
Add default
/
Button
Play/
/
Single-frame
Single-frame
Speed up
Full Screen
Exit
play
reverse play
Previous day
Stop
Next day
Scaling
Process bar
Video type
Digital Zoom
/
up/down the
time line
Smart Search
Playback progress bar: use the mouse to click any point of the progress bar or drag the progress bar to
locate special frames.
6.1.5 Playing Back by System Logs
Purpose:
Play back record file(s) associated with channels after searching system logs.
Steps:
1. Enter Log Information interface.
Menu&gt;Maintenance&gt;Log Information
2. Click Log Search tab to enter Playback by System Logs.
Set search time and type and click Search button.
83
User Manual of Digital Video Recorder
Figure 6. 18 System Log Search Interface
3. Choose a log with record file and click
button to enter Playback interface.
If there is no record file at the time point of the log, the message box “No result found” will pop up.
Figure 6. 19 Result of System Log Search
4. Playback management.
The toolbar in the bottom part of Playback interface can be used to control playing process.
Figure 6. 20 Interface of Playback by Log
84
User Manual of Digital Video Recorder
6.1.6 Playing Back External File
Purpose:
Perform the following steps to look up and play back files in the external devices.
Steps:
1. Enter Tag Search interface.
Menu&gt;Playback
2. Select the External File in the drop-down list on the top-left side.
The files are listed in the right-side list.
You can click the
button to refresh the file list.
3. Select and click the
button to play back it.
Figure 6. 21 Interface of External File Playback
85
User Manual of Digital Video Recorder
6.2 Auxiliary Functions of Playback
6.2.1 Playing Back Frame by Frame
Purpose:
Play video files frame by frame, in order to check image details of the video when abnormal events happen.
Steps:
• Using a Mouse
Go to Playback interface and click button
and
until the speed changes to Single frame. One click
on the playback screen represents playback or adverse playback of one frame. It is also feasible to use
button
in toolbar.
• Using the front panel (Not supported with DS-7200HFHI-SL&amp;SE)
Press the
button to set the speed to Single frame. One click on the playback screen or press
button
on the front panel represents playback or adverse playback of one frame.
6.2.2 Smart Search
Purpose:
In order to locate motion detection event easily and accurately in the playback progress bar, you are allowed to
analyze a certain area (scene) dynamically, and to get all of the related motion detection events that occurred in
this area.
Steps:
1. Go to Playback interface and play the video.
Figure 6. 22 Interface of Playback by Time
2. Click the
button to go to analysis area selection interface.
86
User Manual of Digital Video Recorder
3. Click and drag the mouse to draw area(s). You can click button
searching area. After drawing area(s), press button
to set the full screen as target
to execute smart search in this area.
Multi-area and full-screen searching modes are supported.
Figure 6. 23 Draw Area of Smart Search
The results of smart search will be marked as
in the progress bar.
Figure 6. 24 Smart Search Result with Video List
Figure 6. 25 Toolbar of Smart Search Playback
Table 6. 5 Detailed Explanation of Smart-search-playback Toolbar
Button
Operation
Button
Audio on/
/
Mute
Previous day
Operation
Button
Start/Stop
/
clipping
Next day
87
Operation
Button
Operation
30s forward
30s reverse
Full Screen
Exit
User Manual of Digital Video Recorder
Button
Operation
Button
Pause reverse
Reverse play/
Button
Operation
Button
Operation
Pause play/
play/
/
Operation
Play/
/
Single-frame
Stop
Single-frame
Speed up
play
reverse play
Add
Add
Tag
customized
default tag
Speed down
management
tag
Scaling
Process bar
Video type
Digital Zoom
/
up/down the
time line
Smart Search
Playback progress bar: use the mouse to click any point of the progress bar or drag the progress bar to
locate special frames.
6.2.3 Digital Zoom
Steps:
1. Click the
button on the playback control bar to enter Digital Zoom interface.
2. Use the mouse to draw a red rectangle and the image within it will be enlarged up to 16 times.
Figure 6. 26 Draw Area for Digital Zoom
3. Right-click the image to exit the digital zoom interface.
6.2.4 Reverse Playback of Multi-channel
Purpose:
88
User Manual of Digital Video Recorder
You can play back record files of multi-channel reversely. Up to 16-ch (with 1920*1080 resolution)
simultaneous reverse playback is supported.
Steps:
1. Enter Playback interface.
Menu&gt;Playback
2. Check more than one checkboxes to select multiple channels and click to select a date on the calendar.
Figure 6. 27 4-ch Synchronous Playback Interface
3. Click
to play back the record files reversely.
89
User Manual of Digital Video Recorder
Chapter 7 Backup
90
User Manual of Digital Video Recorder
7.1 Backing up Record Files
Before you start:
Please insert the backup device(s) into the device.
7.1.1 Quick Export
Purpose:
Export record files to backup device(s) quickly.
Steps:
1. Enter Video Export interface.
Menu&gt;Export&gt;Normal
2. Check the checkbox of the channel(s) you want to back up and click Quick Export button.
The time duration of record files on a specified channel cannot exceed one day. Otherwise, the
message box “Max. 24 hours are allowed for quick export.” pops up.
Figure 7. 1 Quick Export Interface
3. Export.
In the Export interface, choose the backup device and click the Export button to start exporting.
Here we use USB Flash Drive and please refer to the next section Normal Backup for more backup
devices supported by the device.
Figure 7. 2 Quick Export using USB1-1
91
User Manual of Digital Video Recorder
Stay in the Exporting interface until all record files are being exported.
Figure 7. 3 Export Finished
4. Check backup result.
Choose the record file in Export interface and click button
to check it.
The Player player.exe will be exported automatically during record file export.
Figure 7. 4 Checkup of Quick Export Result Using USB1-1
7.1.2 Backing up by Normal Video Search
Purpose:
The record files can be backed up to various USB devices, such as USB flash drives, USB HDDs, and USB
writer.
Backup using USB flash drives, USB HDDs, and USB writer
Steps:
1. Enter Export interface.
Menu&gt;Export&gt;Normal
2. Set search condition and click Search button to enter the search result interface.
92
User Manual of Digital Video Recorder
Figure 7. 5 Result of Normal Video Search for Backup
3. Select record files you want to back up.
Click button
to play the record file if you want to check it.
Check the checkbox before the record files you want to back up.
The size of the currently selected files is displayed in the lower-left corner of the window.
4. Export.
Click Export button and start backup.
If the inserted USB device is not recognized:
• Click the Refresh button.
• Reconnect device.
• Check for compatibility from vendor.
You can also format the USB device by clicking the Format button.
Figure 7. 6 Export by Normal Video Search using USB Flash Drive
93
User Manual of Digital Video Recorder
Figure 7. 7 Export by Normal Video Search using USB Writer
Stay in the Exporting interface until all record files are exported with pop-up message box “Export finished”.
Figure 7. 8 Export Finished
5. Check backup result.
Choose the record file in Export interface and click
button to check it.
The Player player.exe will be exported automatically during record file export.
Figure 7. 9 Checkup of Export Result using USB Flash Drive
94
User Manual of Digital Video Recorder
Figure 7. 10 Checkup of Export Result using USB Writer
Backup using eSATA HDDs
Steps:
1. Enter Record&gt;Advanced and set the usage of eSATA HDD at “Export”.
Menu&gt;Record&gt;Advanced
Choose eSATA and set its usage at Export. Click Yes when pop-up message box “System will reboot
automatically if the usage of eSATA is changed. Continue?”
The usages of eSATA HDD contain Record and Export. And changes in usage will take effective
after rebooting the device.
2. Enter Export interface.
Menu&gt;Export&gt;Normal
Set search condition and click Search button to enter the search result interface.
3. Select record files you want to back up.
Click button
to play the record file if you want to check it.
Tick record files you want to back up.
The size of the currently selected files is displayed in the lower-left corner of the window.
95
User Manual of Digital Video Recorder
Figure 7. 11 Result of Normal Video Search for Backup
4. Export.
Click Export button and start backup.
 Please format the eSATA first when using it for the first time.
 If the inserted eSATA HDD is not recognized:
• Click the Refresh button.
• Reconnect device.
• Check for compatibility from vendor.
You can also format eSATA HDD via the device.
Figure 7. 12 Export by Normal Video Search Using eSATA HDD
Stay in the Exporting interface until all record files are exported with pop-up message “Export finished”.
96
User Manual of Digital Video Recorder
Figure 7. 13 Export Finished
5. Check backup result.
Choose the record file in Export interface and click button
to check it.
The Player player.exe will be exported automatically during record file export.
Figure 7. 14 Checkup of Export Result Using eSATA HDD
7.1.3 Backing up by Event Search
Purpose:
Back up event-related record files using USB devices, such as USB flash drives, USB HDDs, and USB writer.
Quick Backup and Normal Backup are supported.
Alarm Input type is supported after the alarm module is plugged in.
Steps:
1. Enter Export interface.
Menu&gt;Export&gt;Event
2. Search for events.
1) Select the type of event from the dropdown list of Event Type.
2) Select the alarm input No. and time.
97
User Manual of Digital Video Recorder
3) Click Search button to enter the Search Result interface.
Figure 7. 15 Event Search for Backup- Motion
Figure 7. 16 Event Search for Backup- Alarm Input
3. Select record files to export.
1) Select an alarm input in the list and click Quick Export button to enter Export interface.
2) Clicking Details button will take you to the interface with detailed information of all channels
triggered by the event.
3) Clicking Quick Export button will export record files of all channels triggered by the selected alarm
input.
Figure 7. 17 Result of Event Search by Motion
98
User Manual of Digital Video Recorder
Figure 7. 18 Result of Video Search by Alarm Input
4) Click Details button to view detailed information of the record file, e.g. start time, end time, file size,
etc.
The size of the currently selected files is displayed in the lower-right corner of the window.
Figure 7. 19 Event Details Interface- Alarm Input
Figure 7. 20 Event Details Interface- Alarm Input
99
User Manual of Digital Video Recorder
4. Export.
Click the Export button and start backing up.
If the inserted USB device is not recognized:
• Click the Refresh button.
• Reconnect device.
• Check for compatibility from vendor.
You can also format USB flash drive or USB HDDs via the device.
Figure 7. 21 Export by Event Using USB Flash Drive
Stay in the Exporting interface until all record files are exported with pop-up message “Export finished”.
Figure 7. 22 Export Finished
5. Check backup result.
The Player player.exe will be exported automatically during record file export.
100
User Manual of Digital Video Recorder
Figure 7. 23 Checkup of Event Export Result Using USB Flash Drive
7.1.4 Backing up Video Clips
Purpose:
You may also select video clips to export directly during Playback, using USB devices, such as USB flash
drives, USB HDDs, and USB writers.
Steps:
1. Enter Playback interface.
Please refer to Chapter 6 Playback.
2. During playback, use buttons
and
in the playback toolbar to start or stop clipping record file(s).
3. Quit Playback interface after finishing clipping and you will be prompted to save the clips.
A maximum of 30 clips can be selected for each channel.
Figure 7. 24 Interface of Playback by Time
101
User Manual of Digital Video Recorder
4. Click Yes to save video clips and enter Export interface, or click No to quit without saving video clips.
Figure 7. 25 Attention to Video Clip Saving
5. Export.
Click Export button and start backup.
If the inserted USB device is not recognized:
• Click the Refresh button.
• Reconnect device.
• Check for compatibility from vendor.
You can also format USB devices by clicking the Format button.
Figure 7. 26 Export Video Clips Using USB Flash Drive
Stay in the Exporting interface until all record files are exported with pop-up message “Export finished”.
Figure 7. 27 Export Finished
6. Check backup result.
102
User Manual of Digital Video Recorder
The Player player.exe will be exported automatically during record file export.
Figure 7. 28 Checkup of Video Clips Export Result Using USB Flash Drive
103
User Manual of Digital Video Recorder
7.2 Managing Backup Devices
Management of USB flash drives and USB HDDs.
Steps:
1. Enter Search Result interface of record files.
Menu&gt;Export&gt;Normal
Set search condition and click Search button to enter Search Result interface.
At least one channel shall be selected.
Figure 7. 29 Normal Video Search for Backup
2. Select record files you want to back up.
Click Export button to enter Export interface.
At least one recording file shall be selected.
Figure 7. 30 Result of Normal Video Search for Backup
3. Backup device management.
104
User Manual of Digital Video Recorder
Figure 7. 31 USB Flash Drive Management
Click New Folder button if you want to create a new folder in the backup device.
Select a record file or folder in the backup device and press button
Select a record file in the backup device and press button
if you want to delete it.
to play it.
Click Format button to format the backup device.
If the inserted USB device is not recognized:
 Click the Refresh button.
 Reconnect device.
 Check for compatibility from vendor.
Management of USB writers
Steps:
1. Enter Search Result interface of record files.
Menu&gt;Export&gt;Normal
Set search condition and click Search button to enter Search Result interface.
At least one channel shall be selected.
Figure 7. 32 Normal Video Search for Backup
2. Select record files you want to back up.
Click Export button to enter Export interface.
105
User Manual of Digital Video Recorder
At least one record file shall be selected.
Figure 7. 33 Result of Normal Video Search for Backup
3. Backup device management.
Figure 7. 34 USB Writer Management
Click Erase button if you want to erase the files from a re-writable CD/DVD.
 There must be a re-writable CD/DVD when you make this operation.
 If the inserted USB writer is not recognized:



Click the Refresh button.
Reconnect device.
Check for compatibility from vendor.
106
User Manual of Digital Video Recorder
Chapter 8 Alarm Settings
107
User Manual of Digital Video Recorder
8.1 Setting Motion Detection
Steps:
1. Enter Motion Detection interface of Camera Management and choose a camera you want to set up motion
detection.
Menu&gt; Camera&gt; Motion
Figure 8. 1 Motion Detection Setup Interface
2. Set detection area and sensitivity.
Check
checkbox to enable motion detection, use the mouse to draw detection area(s) and drag the
sensitivity bar to set sensitivity.
Click
to set alarm response actions.
Figure 8. 2 Set Detection Area and Sensitivity
3. Click Trigger Channel tab and select one or more channels which will start to record or become
full-screen monitoring when motion alarm is triggered.
108
User Manual of Digital Video Recorder
Figure 8. 3 Set Trigger Camera of Motion Detection
4. Set arming schedule of the channel.
Select Arming Schedule tab to set the channel’s arming schedule.
Choose one day of a week and up to eight time periods can be set within each day. Or you can click the
Copy button to copy the time period settings to other day(s).
Time periods shall not be repeated or overlapped.
Figure 8. 4 Set Arming Schedule of Motion Detection
5. Click Handling tab to set up alarm response actions of motion alarm (please refer to Chapter 8.6 Setting
Alarm Response Actions).
Repeat the above steps to set up arming schedule of other days of a week.
Click the OK button to complete the motion detection settings of the channel.
6. If you want to set motion detection for another channel, repeat the above steps or just copy the above
settings to it.
You are not allowed to copy the “Trigger Channel” action.
109
User Manual of Digital Video Recorder
Figure 8. 5 Copy Settings of Motion Detection
110
User Manual of Digital Video Recorder
8.2 Setting Sensor Alarms
Purpose:
Set up handling method of an external sensor alarm.
Steps:
1. Enter Alarm Settings of System Configuration and select an alarm input.
Menu&gt; Configuration&gt; Alarm
Select Alarm Input tab to enter Alarm Input Settings interface.
Figure 8. 6 Alarm Status Interface of System Configuration
2. Set the handling method of the selected alarm input.
Check the Setting checkbox and click Handling button to set its alarm response actions.
Figure 8. 7 Alarm Input Settings Interface
3. Select Trigger Channel tab and select one or more channels which will start to record or become
full-screen monitoring when an external alarm is input.
4. Select Arming Schedule tab to set the channel’s arming schedule.
Choose one day of a week and Max. eight time periods can be set within each day.
Time periods shall not be repeated or overlapped.
5. Select Handling tab to set up alarm response actions of the alarm input (please refer to Chapter 8.6
Setting Alarm Response Actions).
Repeat the above steps to set up arming schedule of other days of a week. You can also use Copy button
to copy an arming schedule to other days.
111
User Manual of Digital Video Recorder
Figure 8. 8 Set Arming Schedule of Alarm Input
6. If necessary, select PTZ Linking tab and set PTZ linkage of the alarm input.
Set PTZ linking parameters and click the OK button to complete the settings of the alarm input.
Please check whether the PTZ or speed dome supports PTZ linkage.
One alarm input can trigger presets, patrol or pattern of more than one channel. But presets, patrols and
patterns are exclusive.
Figure 8. 9 Set PTZ Linking of Alarm Input
7. If you want to set handling method of another alarm input, repeat the above steps or just copy the above
settings to it.
112
User Manual of Digital Video Recorder
Figure 8. 10 Copy Settings of Alarm Input
113
User Manual of Digital Video Recorder
8.3 Detecting Video Loss
Purpose:
Detect video loss of a channel and take alarm response action(s).
Steps:
1. Enter Video Loss interface of Camera Management and select a channel you want to detect.
Menu&gt; Camera&gt; Video Loss
Figure 8. 11 Video Loss Setup Interface
2. Set up handling method of video loss.
Check the checkbox of “Enable Video Loss Alarm”.
Click
button to set up handling method of video loss.
3. Set arming schedule of the channel.
Select Arming Schedule tab to set the channel’s arming schedule.
Choose one day of a week and up to eight time periods can be set within each day. Or you can click the
Copy button to copy the time period settings to other day(s).
Time periods shall not be repeated or overlapped.
Figure 8. 12 Set Arming Schedule of Video Loss
Repeat the above steps to set arming schedule of other days of a week. You can also use Copy button to
copy an arming schedule to other days.
114
User Manual of Digital Video Recorder
4. Select Handling tab to set up alarm response action of video loss (please refer to Chapter 8.6 Setting
Alarm Response Actions).
5. Click the OK button to complete the video loss settings of the channel.
Repeat the above steps to finish settings of other channels, or click the Copy button copy the above
settings to them.
115
User Manual of Digital Video Recorder
8.4 Detecting Video Tampering
Purpose:
Trigger alarm when the lens is covered and take alarm response action(s).
Steps:
1. Enter Video Tampering interface of Camera Management and select a channel you want to detect video
tampering.
Menu&gt; Camera&gt; Video Tempering Detection
Figure 8. 13 Video Tempering Interface
2. Check the checkbox of “Enable Video Tampering”.
3. Drag the sensitivity bar and choose a proper sensitivity level.
4. Click
to set handling method of video tampering. Set arming schedule and alarm response actions of
the channel.
1) Click Arming Schedule tab to set the arming schedule of response action.
2) Choose one day of a week and up to eight time periods can be set within each day.
Time periods shall not be repeated or overlapped.
Figure 8. 14 Set Arming Schedule of Video Tampering
3) Select Handling tab to set alarm response actions of video tampering alarm (please refer to Chapter
116
User Manual of Digital Video Recorder
8.6 Setting Alarm Response Actions).
Repeat the above steps to set arming schedule of other days of a week. You can also use Copy button
to copy an arming schedule to other days.
4) Click the OK button to complete the video tampering settings of the channel.
Repeat the above steps to finish settings of other channels, or click the Copy button copy the above
settings to them.
117
User Manual of Digital Video Recorder
8.5 Handling Exceptions
Purpose:
Exception settings refer to the handling method of various exceptions, e.g.
•
•
•
•
•
•
•
HDD Full: The HDD is full.
HDD Error: Writing HDD error, unformatted HDD, etc.
Network Disconnected: Disconnected network cable.
IP Conflicted: Duplicated IP address.
Illegal Login: Incorrect user ID or password.
Input/Recording Resolution Mismatch: The input resolution is smaller than the recording resolution.
Record Exception: No space for saving recorded files.
Steps:
Enter Exception interface of System Configuration and handle various exceptions.
Menu&gt; Configuration&gt; Exceptions
Please refer to Chapter 8.6 Setting Alarm Response Actions for detailed alarm response actions.
DS-7200HFHI-SL&amp;SE&amp;ST
DS-7300HFHI-ST and DS-8100HFHI-ST
Figure 8. 15 Exceptions Settings Interface
118
User Manual of Digital Video Recorder
8.6 Setting Alarm Response Actions
Purpose:
Take alarm response actions will be activated when an alarm or exception occurs, including Full Screen
Monitoring, Audible Warning (buzzer), Notify Surveillance Center, Send Email and Trigger Alarm Output.
 Full Screen Monitoring
When an alarm is triggered, the local monitor (HDMI or VGA monitor) display in full screen the video image
from the alarming channel configured for full screen monitoring.
If alarms are triggered simultaneously in several channels, their full-screen images will be switched at an
interval of 10 seconds (default dwell time). A different dwell time can be set by going to Menu &gt;
Configuration &gt;Live View.
Auto-switch will terminate once the alarm stops and you will be taken back to the Live View interface.

Audible Warning
Trigger an audible beep when an alarm is detected.

Notify Surveillance Center
Sends an exception or alarm signal to remote alarm host when an event occurs. The alarm host refers to the PC
installed with Remote Client.
The alarm signal will be transmitted automatically at detection mode when remote alarm host is
configured. Please refer to Chapter 9.2.6 Configuring the Remote Alarm Host for details of alarm host
configuration.

Send Email
Send an email with alarm information to a user or users when an alarm is detected.
Please refer to Chapter 9.2.10 Configuring Email for details of Email configuration.

Trigger Alarm Output
Trigger an alarm output when an alarm is triggered.
Steps:
1. Enter Alarm Output interface.
Menu&gt; Configuration&gt; Alarm&gt; Alarm Output
Select an alarm output and set alarm name and dwell time. Click
button to set the arming schedule of
alarm output.
If “Manually Clear” is selected in the dropdown list of Dwell Time, you can clear it only by going to
Menu&gt; Manual&gt; Alarm.
Figure 8. 16 Alarm Output Settings Interface
2. Set up arming schedule of the alarm output.
119
User Manual of Digital Video Recorder
Choose one day of a week and up to 8 time periods can be set within each day.
Time periods shall not be repeated or overlapped.
Figure 8. 17 Set Arming Schedule of Alarm Output
3. Repeat the above steps to set arming schedule of other days of a week. You can also use Copy button to
copy an arming schedule to other days.
Click the OK button to complete the arming schedule setting of alarm output.
4. Click the Apply button to save the settings.
120
User Manual of Digital Video Recorder
8.7 Triggering or Clearing Alarm Output
Manually
Purpose:
Sensor alarm can be triggered or cleared manually. If “Manually Clear” is selected in the dropdown list of dwell
time of an alarm output, the alarm can be cleared only by clicking Clear button in the following interface.
Steps:
Select the alarm output you want to trigger or clear and make related operations.
Menu&gt; Manual&gt; Alarm
Click Trigger/Clear button if you want to trigger or clear an alarm output.
Click Trigger All button if you want to trigger all alarm outputs.
Click Clear All button if you want to clear all alarm output.
Figure 8. 18 Clear or Trigger Alarm Output Manually
121
User Manual of Digital Video Recorder
Chapter 9 Network Settings
122
User Manual of Digital Video Recorder
9.1 Configuring General Settings
Purpose:
Network settings must be properly configured before you operate DVR over network.
Steps:
1. Enter the Network Settings interface.
Menu &gt; Configuration &gt; Network
DS-8100HFHI-ST
Other Models
Figure 9. 1 Network Settings Interface
2. Select the General tab.
3. In the General Settings interface, you can configure the following settings: Working mode (applicable for
DS-8100HFHI-ST only), NIC Type, IPv4 Address, IPv4 Gateway, MTU and DNS Server.
If the DHCP server is available, you can check the checkbox of DHCP to automatically obtain an IP
address and other network settings from that server.
The valid value of MTU is from 500 to 1500.
123
User Manual of Digital Video Recorder
4. After having configured the general settings, click the Apply button to save the settings.
Working Mode
There are two 10M/100M/1000M NIC cards provided by the DS-8100HFHI-ST series device, and it allows
the device to work in the Multi-address, Load Balance and Net-fault Tolerance modes.
Multi-address Mode: The parameters of the two NIC cards can be configured independently. You can select
LAN1 or LAN2 in the NIC type field for parameter settings.
You can select one NIC card as default route. And then the system is connecting with the extranet the data will
be forwarded through the default route.
Net-fault Tolerance Mode: The two NIC cards use the same IP address, and you can select the Main NIC to
LAN1 or LAN2. By this way, in case of one NIC card failure, the device will automatically enable the other
standby NIC card so as to ensure the normal running of the whole system.
Load Balance Mode: By using the same IP address and two NIC cards share the load of the total bandwidth,
which enables the system to provide two Gigabit network capacity.
124
User Manual of Digital Video Recorder
9.2 Configuring Advanced Settings
9.2.1 Configuring PPPoE Settings
Purpose:
The DVR also allows access by Point-to-Point Protocol over Ethernet (PPPoE).
Steps:
1. Enter the Network Settings interface.
Menu &gt; Configuration &gt; Network
2. Select the PPPoE tab to enter the PPPoE Settings interface.
Figure 9. 2 PPPoE Settings Interface
3. Check the PPPoE checkbox to enable this feature.
4. Enter User Name and Password for PPPoE access.
The User Name and Password should be assigned by your ISP.
5. Click the Apply button to save the settings.
6. After successful settings, the system asks you to reboot the device to enable the new settings, and the
PPPoE dial-up is automatically connected after reboot.
You can go to Menu &gt; Maintenance &gt; System Info &gt; Network interface to view the status of PPPoE
connection. Please refer to Chapter 12.1.5 Viewing Network Information for PPPoE status.
9.2.2 Configuring DDNS
Purpose:
If your DVR is set to use PPPoE as its default network connection, you may set Dynamic DNS (DDNS) to be
used for network access.
Prior registration with your ISP is required before configuring the system to use DDNS.
Steps:
1. Enter the Network Settings interface.
Menu &gt; Configuration &gt; Network
2. Select the DDNS tab to enter the DDNS Settings interface.
125
User Manual of Digital Video Recorder
Figure 9. 3 DDNS Settings Interface
3. Check the DDNS checkbox to enable this feature.
4. Select DDNS Type. Five different DDNS types are selectable: IPServer, DynDNS, PeanutHull, NO-IP
and HiDDNS.
 IPServer: Enter Server Address for IPServer.
Figure 9. 4 IPServer Settings Interface
 DynDNS:
1) Enter Server Address for DynDNS (i.e. members.dyndns.org).
2) In the DVR Domain Name text field, enter the domain obtained from the DynDNS website.
3) Enter the User Name and Password registered in the DynDNS website.
Figure 9. 5 DynDNS Settings Interface
 PeanutHull: Enter the User Name and Password obtained from the PeanutHull website.
Figure 9. 6 PeanutHull Settings Interface
 NO-IP:
Enter the account information in the corresponding fields. Refer to the DynDNS settings.
1) Enter Server Address for NO-IP.
2) In the DVR Domain Name text field, enter the domain obtained from the NO-IP website
(www.no-ip.com).
3) Enter the User Name and Password registered in the NO-IP website.
126
User Manual of Digital Video Recorder
Figure 9. 7 NO-IP Settings Interface
 HiDDNS:
1) The Server Address of the HiDDNS server appears by default: www.hik-online.com.
2) Enter the Device Domain Name. You can use the alias you registered in the HiDDNS server or
define a new device domain name. If a new alias of the device domain name is defined in the DVR,
it will replace the old one registered on the server. You can register the alias of the device domain
name in the HiDDNS server first and then enter the alias to the Device Domain Name in the DVR;
you can also enter the domain name directly on the DVR to create a new one.
Figure 9. 8 HiDDNS Settings Interface
Register the device on the HiDDNS server.
1) Go to the HiDDNS website: www.hik-online.com.
2) Click
to register an account if you do not have one and use the account to log
in.
Figure 9. 9 Register an Account
3) In the Device Management interface, click
127
to register the device.
User Manual of Digital Video Recorder
Figure 9. 10 Register the Device
The device name can only contain the lower-case English letter, numeric and ‘-’; and it
must start with the lower-case English letter and cannot end with ‘-’.
Access the Device via Web Browser or Client Software
After having successfully registered the device on the HiDDNS server, you can access your
device via web browser or Client Software with the Device Domain Name (Device Name).
OPTION 1: Access the Device via Web Browser
Open a web browser, and enter http://www.hik-online.com/alias in the address bar. Alias refers
to the Device Domain Name on the device or the Device Name on the HiDDNS server.
Example: http://www.hik-online.com/dvr
If you mapped the HTTP port on your router and changed it to port No. except 80, you
have to enter http://www.hik-online.com/alias:HTTP port in the address bar to access the
device. You can refer to Chapter 9.2.5 Configuring UPnPTM for the mapped HTTP port
No.
OPTION 2: Access the devices via iVMS4200
For iVMS-4200, in the Add Device window, select
and then edit the device
information.
Nickname: Edit a name for the device as you want.
Server Address: www.hik-online.com
Device Domain Name: It refers to the Device Domain Name on the device or the Device
Name on the HiDDNS server you created.
User Name: Enter the user name of the device. By default it is admin.
Password: Enter the password of the device. By default it is 12345.
128
User Manual of Digital Video Recorder
Figure 9. 11 Access Device via iVMS4200
5. Click the Apply button to save and exit the interface.
9.2.3 Configuring NTP Server
Purpose:
A Network Time Protocol (NTP) Server can be configured on your DVR to ensure the accuracy of system
date/time.
Steps:
1. Enter the Network Settings interface.
Menu &gt; Configuration &gt; Network
2. Select the NTP tab to enter the NTP Settings interface.
Figure 9. 12 NTP Settings Interface
3. Check the Enable NTP checkbox to enable this feature.
4. Configure the following NTP settings:
• Interval: Time interval between the two synchronizing actions with NTP server. The unit is minute.
• NTP Server: IP address of NTP server.
• NTP Port: Port of NTP server.
5. Click the Apply button to save and exit the interface.
The time synchronization interval can be set from 1 to 10080 minutes, and the default value is 60
minutes. If the DVR is connected to a public network, you should use a NTP server that has a time
synchronization function, such as the server at the National Time Center (IP Address: 210.72.145.44). If
the DVR is set in a more customized network, NTP software can be used to establish a NTP server used
for time synchronization.
129
User Manual of Digital Video Recorder
9.2.4 Configuring SNMP
Purpose:
You can use SNMP protocol to get device status and parameters related information.
Steps:
1. Enter the Network Settings interface.
Menu &gt; Configuration &gt; Network
2. Select the SNMP tab to enter the SNMP Settings interface.
Figure 9. 13 SNMP Settings Interface
3. Check the Enable SNMP checkbox to enable this feature.
4. Configure the following SNMP settings:
• Trap Address: IP Address of SNMP host.
• Trap Port: Port of SNMP host.
Figure 9. 14 Configure SNMP Settings
5. Click the Apply button to save and exit the interface.
Before setting the SNMP, please download the SNMP software and manage to receive the device
information via SNMP port. By setting the Trap Address, the DVR is allowed to send the alarm event
and exception message to the surveillance center.
9.2.5 Configuring UPnP™
Purpose:
Universal Plug and Play (UPnP™) can permit the device seamlessly discover the presence of other network
devices on the network and establish functional network services for data sharing, communications, etc. You can
use the UPnP™ function to enable the fast connection of the device to the WAN via a router without port
mapping.
130
User Manual of Digital Video Recorder
Before you start:
If you want to enable the UPnP™ function of the device, you must enable the UPnP™ function of the router to
which your device is connected. When the network working mode of the device is set as multi-address, the
Default Route of the device should be in the same network segment as that of the LAN IP address of the router.
Steps:
1. Enter the Network Settings interface.
Menu &gt; Configuration &gt; Network
2. Select the UPnP tab to enter the UPnP™ interface.
Figure 9. 15 UPnP™ Settings Interface
3. Check
checkbox to enable UPnP™.
4. Select the Mapping Type as Manual or Auto in the drop-down list.
OPTION 1: Auto
If you select Auto, the Port Mapping items are read-only, and the external ports are set by the router
automatically.
1) Click Apply button to save the settings.
2) You can click Refresh button to get the latest status of the port mapping.
Figure 9. 16 UPnP™ Settings Finished-Auto
OPTION 2: Manual
If you select Manual as the mapping type, you can edit the external port on your demand by clicking
to activate the External Port Settings dialog box.
Steps:
1) Click
to activate the External Port Settings dialog box. Configure the external port No. for server
port, http port and RTSP port respectively.
 You can use the default port No., or change it according to actual requirements.
 External Port indicates the port No. for port mapping in the router.
 The value of the RTSP port No. should be 554 or between 1024 and 65535, while the value of
131
User Manual of Digital Video Recorder
the other ports should be between 1 and 65535 and the value must be different from each other.
If multiple devices are configured for the UPnP™ settings under the same router, the value of
the port No. for each device should be unique.
Figure 9. 17 External Port Settings Dialog Box
2) Click Apply button to save the settings.
3) You can click Refresh button to get the latest status of the port mapping.
Figure 9. 18 UPnP™ Settings Finished-Manual
9.2.6 Configuring the Remote Alarm Host
Purpose:
With a remote alarm host configured, the DVR will send the alarm event or exception message to the host when
an alarm is triggered. The remote alarm host must have the Network Video Surveillance software installed.
Steps:
1. Enter the Network Settings interface.
Menu &gt; Configuration &gt; Network
2. Select the More Settings tab to enter the More Settings interface.
Figure 9. 19 More Settings Interface
3. Enter Alarm Host IP and Alarm Host Port in the text fields.
The Alarm Host IP refers to the IP address of the remote PC on which the CMS (Client Management
132
User Manual of Digital Video Recorder
System) software (e.g., iVMS-4200) is installed, and the Alarm Host Port must be the same as the alarm
monitoring port configured in the software (default port is 7200).
Figure 9. 20 Configure Alarm Host
4. Click the Apply button to save and exit the interface.
9.2.7 Configuring Multicast
Purpose:
The multicast can be configured to realize live view for more than 128 cameras through network.
A multicast address spans the Class-D IP range of 224.0.0.0 to 239.255.255.255. It is recommended to use the IP
address ranging from 239.252.0.0 to 239.255.255.255.
Steps:
1. Enter the Network Settings interface.
Menu &gt; Configuration &gt; Network
2. Select the More Settings tab to enter the More Settings interface.
3. Set Multicast IP. When adding a device to the CMS (Client Management System) software, the multicast
address must be the same as the DVR’s multicast IP.
Figure 9. 21 Configure Multicast
4. Click the Apply button to save and exit the interface.
9.2.8 Configuring RTSP
Purpose:
The RTSP (Real Time Streaming Protocol) is a network control protocol designed for using in entertainment and
communications systems to control streaming media servers.
Steps:
1. Enter the Network Settings menu:
Menu &gt; Configuration &gt; Network
2. Select the More Settings tab to enter the More Settings menu.
133
User Manual of Digital Video Recorder
Figure 9. 22 RTSP Settings Interface
3. Enter the RTSP port in the text field of RTSP Service Port. The default RTSP port is 554, and you can
change it according to different requirements.
4. Click the Apply button to save and exit the menu.
9.2.9 Configuring Server and HTTP Ports
Purpose:
You can change the server and HTTP ports in the Network Settings menu. The default server port is 8000 and
the default HTTP port is 80.
Steps:
1. Enter the Network Settings interface.
Menu &gt; Configuration &gt; Network
2. Select the More Settings tab to enter the More Settings interface, as shown in Figure 9. 23.
3. Enter new Server Port and HTTP Port.
Figure 9. 23 Host/Others Settings Menu
4. Enter the Server Port and HTTP Port in the text fields. The default Server Port is 8000 and the HTTP Port
is 80, and you can change them according to different requirements.
5. Click the Apply button to save and exit the interface.
The Server Port should be set to the range of 2000-65535 and it is used for remote client software access.
The HTTP port is used for remote web browser access.
9.2.10 Configuring Email
Purpose:
The system can be configured to send an Email notification to all designated users if an event is detected, e.g. an
alarm or motion event is detected, etc.
134
User Manual of Digital Video Recorder
Before configuring the Email settings, the DVR must be connected to a local area network (LAN) that maintains
an SMTP mail server. The network must also be connected to either an intranet or the Internet depending on the
location of the e-mail accounts to which you want to send notification. Additional, the Preferred DNS server
must be configured.
Before you start:
Make sure you have configured the IPv4 Address, IPv4 Subnet Mask, IPv4 Gateway and the Preferred DNS
Server in the Network Settings menu. Please refer to Chapter 9.1 Configuring General Settings for detailed
information.
Steps:
1. Enter the Network Settings interface.
Menu &gt; Configuration &gt; Network
2. Select the Email tab to enter the Email Settings interface.
Figure 9. 24 Email Settings Interface
3. Configure the following Email settings:
Enable Server Authentication (optional): Check the checkbox to enable the server authentication
feature.
User Name: The user account of sender’s Email for SMTP server authentication.
Password: The password of sender’s Email for SMTP server authentication.
SMTP Server: The SMTP Server IP address or host name (e.g., smtp.263xmail.com).
SMTP Port No.: The SMTP port. The default TCP/IP port used for SMTP is 25.
Enable SSL (optional): Click the checkbox to enable SSL if required by the SMTP server.
Sender: The name of sender.
Sender’s Address: The Email address of sender.
Select Receivers: Select the receiver. Up to 3 receivers can be configured.
Receiver: The name of the receiver of the Email.
Receiver’s Address: The Email address of the receiver.
Enable Attached Pictures: Check the checkbox of Enable Attached Picture if you want to send email
with attached alarm images. The interval is the time between two captures of the alarm images.
Interval: The interval refers to the time between two actions of sending attached pictures.
E-mail Test: Sends a test message to verify that the SMTP server can be reached.
4. Click the Apply button to save the Email settings.
135
User Manual of Digital Video Recorder
5. You can click the Test button to test whether your Email settings work. The corresponding Attention
message box pops up.
Figure 9. 25 Email Testing Attention
136
User Manual of Digital Video Recorder
9.3 Checking Network Traffic
Purpose:
You can check the network traffic to obtain real-time information of DVR such as linking status, MTU,
sending/receiving rate, etc.
Steps:
1. Enter the Network Traffic interface.
Menu &gt; Maintenance &gt; Net Detect
Figure 9. 26 Network Traffic Interface
2. You can view the sending rate and receiving rate information on the interface. The traffic data is refreshed
every 1 second.
137
User Manual of Digital Video Recorder
9.4 Configuring Network Detection
Purpose:
You can obtain network connecting status of DVR through the network detection function, including network
delay, packet loss, etc.
9.4.1 Testing Network Delay and Packet Loss
Steps:
1. Enter the Network Traffic interface.
Menu &gt; Maintenance &gt; Net Detect
2. Click the Network Detection tab to enter the Network Detection menu.
Figure 9. 27 Network Detection Interface
3. Select a NIC to test network delay and packet loss.
4. Enter the destination address in the text field of Destination Address.
5. Click the Test button to start testing network delay and packet loss. The testing result pops up on the
window. If the testing is failed, the error message box will pop up as well.
Figure 9. 28 Testing Result of Network Delay and Packet Loss
9.4.2 Exporting Network Packet
Purpose:
By connecting the DVR to network, the captured network data packet can be exported to USB-flash disk, SATA
and other local backup devices.
Steps:
1. Enter the Network Traffic interface.
Menu &gt; Maintenance &gt; Net Detect
2. Click the Network Detection tab to enter the Network Detection interface.
138
User Manual of Digital Video Recorder
3. Select the backup device from the dropdown list of Device Name.
Click the Refresh button if the connected local backup device cannot be displayed. When it fails to
detect the backup device, please check whether it is compatible with the DVR. You can format the
backup device if the format is incorrect.
Figure 9. 29 Export Network Packet
4. Click the Export button to start exporting.
5. After the exporting is complete, click OK to finish the packet export.
Figure 9. 30 Packet Export Attention
Up to 1M data can be exported each time.
139
User Manual of Digital Video Recorder
9.4.3 Checking Network Status
Purpose:
You can also check the network status and quick set the network parameters in this interface.
Steps:
Click Status on the right bottom of the page.
Figure 9. 31 Checking Network Status
If the network is normal the following message box pops out.
Figure 9. 32 Network Status Checking Result
If the message box pops out with other information instead of this one, you can click Network button to show
the quick setting interface of the network parameters.
Figure 9. 33 Network Parameters Configuration
9.4.4 Checking Network Statistics
Purpose:
You can check the network statistics to obtain the real-time information of the device.
Steps:
140
User Manual of Digital Video Recorder
1. Enter the Network Statistics interface.
Menu &gt; Maintenance&gt; Net Detect
2. Click the Network Stat. tab to enter the Network Statistics menu.
Figure 9. 34 Network Stat. Interface
3. View the bandwidth of Remote Live View, bandwidth of Remote Playback, and bandwidth of Net Total Idle.
4. Click Refresh button to get the latest bandwidth statistics.
141
User Manual of Digital Video Recorder
Chapter 10 HDD Management
142
User Manual of Digital Video Recorder
10.1 Initializing HDDs
Purpose:
A newly installed hard disk drive (HDD) must be initialized before it can be used with your DVR.
Steps:
1. Enter the HDD Information interface.
Menu &gt; HDD&gt;General.
Figure 10. 1 HDD Information Interface
2. Select HDD to be initialized.
3. Click the Init button.
Figure 10. 2 Confirm Initialization
4. Select the OK button to start initialization.
Figure 10. 3 Start Initialization
5. After the HDD has been initialized, the status of the HDD will change from Uninitialized to Normal.
Figure 10. 4 HDD Status Changes to Normal
Initializing the HDD will erase all data on it.
143
User Manual of Digital Video Recorder
10.2 Managing Network HDD
Purpose:
You can add the allocated NAS or disk of IP SAN to DVR, and use it as network HDD.
Steps:
1. Enter the HDD Information interface.
Menu &gt; HDD&gt;General
Figure 10. 5 HDD Information Interface
2. Click the Add button to enter the Add NetHDD interface, as shown in Figure 10. 6.
Figure 10. 6 HDD Information Interface
3. Add the allocated NetHDD.
4. Select the type to NAS or IP SAN.
5. Configure the NAS or IP SAN settings.
• Add NAS disk:
1) Enter the NetHDD IP address in the text field.
2) Enter the NetHDD Directory in the text field.
3) Click the OK button to add the configured NAS disk.
Up to 8 NAS disks can be added.
144
User Manual of Digital Video Recorder
Figure 10. 7 Add NAS Disk
• Add IP SAN:
1) Enter the NetHDD IP address in the text field.
2) Click the Search button to the available IP SAN disks.
3) Select the IP SAN disk from the list shown below.
4) Click the OK button to add the selected IP SAN disk.
Up to 1 IP SAN disk can be added.
Figure 10. 8 Add IP SAN Disk
6. After having successfully added the NAS or IP SAN disk, return to the HDD Information menu. The added
NetHDD will be displayed in the list.
If the added NetHDD is uninitialized, please select it and click the Init button for initialization.
Figure 10. 9 Initialize Added NetHDD
145
User Manual of Digital Video Recorder
10.3 Managing eSATA
Purpose:
When there is an external eSATA device connected to DVR, you can configure eSATA for the use of Record or
Export, and you can manage the eSATA in the DVR.
Steps:
1. Enter the Advanced Record Settings interface.
Menu &gt;Record&gt;Advanced
2. Select the eSATA type to Export or Record from the dropdown list of eSATA.
Export: use the eSATA for backup. Refer to Backup using eSATA HDDs in Chapter 7.1.2 Backing up by
Normal Video Search for operating instructions.
Record: use the eSATA for record. Refer to the following steps for operating instructions.
Figure 10. 10 Set eSATA Mode
3. When the eSATA type is selected to Record, enter the HDD Information interface.
Menu &gt; HDD&gt;General
4. Edit the property of the selected eSATA, or initialize it is required.
Two storage modes can be configured for the eSATA when it is used for Record. Please refer to
Chapter 10.4 Managing HDD Group and Chapter 10.5 Configuring Quota Mode for details.
Figure 10. 11 Initialize Added eSATA
146
User Manual of Digital Video Recorder
10.4 Managing HDD Group
10.4.1 Setting HDD Groups
Purpose:
Multiple HDDs can be managed in groups. Video from specified channels can be recorded onto a particular HDD
group through HDD settings.
Steps:
1. Enter the Storage Mode interface.
Menu &gt; HDD &gt; Advanced
2. Set the Mode to Group, as shown in Figure 10. 12.
Figure 10. 12 Storage Mode Interface
3. Click the Apply button and the following Attention box will pop up.
Figure 10. 13 Attention for Reboot
4. Click the Yes button to reboot the device to activate the changes.
5. After reboot of device, enter the HDD Information interface.
Menu &gt; HDD &gt; General
6. Select HDD from the list and click the
Figure 10. 14.
icon to enter the Local HDD Settings interface, as shown in
147
User Manual of Digital Video Recorder
Figure 10. 14 Local HDD Settings Interface
7. Select the Group number for the current HDD.
The default group No. for each HDD is 1.
8. Click the OK button to confirm the settings.
Figure 10. 15 Confirm HDD Group Settings
9. In the pop-up Attention box, click the Yes button to finish the settings.
10.4.2 Setting HDD Property
Purpose:
The HDD property can be set to redundancy, read-only or read/write (R/W). Before setting the HDD property,
please set the storage mode to Group (refer to step1-4 of Chapter 10.4.1 Setting HDD Groups).
A HDD can be set to read-only to prevent important recorded files from being overwritten when the HDD becomes
full in overwrite recording mode.
When the HDD property is set to redundancy, the video can be recorded both onto the redundancy HDD and the
R/W HDD simultaneously so as to ensure high security and reliability of video data.
Steps:
1. Enter the HDD Information interface.
Menu &gt; HDD &gt; General
2. Select HDD from the list and click the
Figure 10. 16.
icon to enter the Local HDD Settings interface, as shown in
148
User Manual of Digital Video Recorder
Figure 10. 16 Set HDD Property
3. Set the HDD property to R/W, Read-only or Redundancy.
4. Click the OK button to save the settings and exit the interface.
5. In the HDD Information menu, the HDD property will be displayed in the list.
At least 2 hard disks must be added on your DVR when you want to set a HDD to Redundancy, and there
is one HDD with R/W property.
149
User Manual of Digital Video Recorder
10.5 Configuring Quota Mode
Purpose
Each camera can be configured with allocated quota for the storage of recorded files.
Steps
1. Enter the Storage Mode interface.
Menu &gt; HDD &gt; Advanced
2. Set the Mode to Quota, as shown in Figure 10. 17.
The DVR must be rebooted to enable the changes to take effect.
Figure 10. 17 Storage Mode Settings Interface
3. Select a camera for which you want to configure quota.
4. Enter the storage capacity in the text field of Max. Record Capacity (GB), as shown in Figure 10. 18.
Figure 10. 18 Configure Record Quota
5. You can copy the quota settings of the current camera to other cameras if required. Click the Copy button to
enter the Copy Camera interface, as shown in Figure 10. 19.
150
User Manual of Digital Video Recorder
Figure 10. 19 Copy Settings to Other Camera(s)
6. Select the camera (s) to be configured with the same quota settings. You can also click the checkbox of
Analog to select all cameras.
7. Click the OK button to finish the Copy settings and back to the Storage Mode interface.
8. Click the Apply button to apply the settings.
If the quota capacity is set to 0, then all cameras will use the total capacity of HDD for record.
151
User Manual of Digital Video Recorder
10.6 Checking HDD Status
Purpose:
You may check the status of the installed HDDs on DVR so as to take immediate check and maintenance in case
of HDD failure.
Checking HDD Status in HDD Information Interface
Steps:
1. Enter the HDD Information interface.
Menu &gt; HDD&gt;General
2. Check the status of each HDD which is displayed on the list, as shown in Figure 10. 20.
Figure 10. 20 View HDD Status (1)
If the status of HDD is Normal or Sleeping, it works normally. If the status is Uninitialized or Abnormal,
please initialize the HDD before use. And if the HDD initialization is failed, please replace it with a new
one.
Checking HDD Status in System Information Interface
Steps:
1. Enter the System Information interface.
Menu &gt; Maintenance &gt; System Info
2. Click the HDD tab to view the status of each HDD displayed on the list, as shown in Figure 10. 21.
Figure 10. 21 View HDD Status (2)
152
User Manual of Digital Video Recorder
10.7 Checking S.M.A.R.T Information
Purpose:
The S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) is a monitoring system for HDD to detect
and report on various indicators of reliability in the hopes of anticipating failures.
Steps:
1. Enter the HDD Detect interface.
Menu &gt; HDD &gt; HDD Detect
2. Click the S.M.A.R.T. Settings tab to enter the interface.
3. Select the HDD to view its S.M.A.R.T. information list, as shown in Figure 10. 22.
If you want to use the HDD even when the S.M.A.R.T. checking is failed, you can check the checkbox
before the Continue to use this disk when self-evaluation is failed item.
Figure 10. 22 S.M.A.R.T Settings Interface
153
User Manual of Digital Video Recorder
10.8 Detecting Bad Sector
Purpose:
You can detect the bad sector of the HDD to check the status of the HDD.
Steps:
1. Enter the HDD Detect interface.
Menu&gt;HDD&gt;HDD Detect
Figure 10. 23 Bad Sector Detection
2. Click the Bad Sector Detection tab to enter the interface.
3. Select a HDD and click the Detect button to start detecting.
Figure 10. 24 Bad Sector Detecting
4. You can click the Pause button to pause the detection and click the Resume button to resume the detection.
5. If there is error information about the HDD, you can click the Error Info button to view the information.
154
User Manual of Digital Video Recorder
10.9 Configuring HDD Error Alarms
Purpose:
You can configure the HDD error alarms when the HDD status is Uninitialized or Abnormal.
Steps:
1. Enter the Exception interface.
Menu &gt; Configuration &gt; Exceptions
2. Select the Exception Type to HDD Error from the dropdown list.
3. Check the checkbox(s) below to select the linkage action(s) for HDD error, as shown in Figure 10. 25.
The linkage actions can be selected to: Audible Warning, Notify Surveillance Center, Send Email and
Trigger Alarm Output.
Trigger alarm output is applicable to the DS-7300HFHI-ST and DS-8100HFHI-ST.
Please refer to Chapter 8.6 Setting Alarm Response Actions.
Figure 10. 25 Configure HDD Error Alarm
4. When the Trigger Alarm Output is selected, you can also select the alarm output to be triggered from the list
below.
5. Click the Apply button to save the settings.
155
User Manual of Digital Video Recorder
Chapter 11 Camera Settings
156
User Manual of Digital Video Recorder
11.1 Configuring OSD Settings
Purpose:
You can configure the OSD (On-screen Display) settings for the camera, including date /time, camera name, etc.
Steps:
1. Enter the OSD Configuration interface.
Menu &gt; Camera &gt; OSD
2. Select the camera to configure OSD settings.
3. Edit the Camera Name in the text field.
4. Configure the Display Name, Display Date and Display Week by checking the checkbox.
5. Select the Date Format, Time Format, Display Mode and the OSD font.
Figure 11. 1 OSD Configuration Interface
6. You can use the mouse to click and drag the text frame on the preview window to adjust the OSD position.
7. Copy Camera Settings
1)
If you want to copy the OSD settings of the current camera to other cameras, click the Copy button to
enter the Copy Camera interface, as shown in Figure 11. 2.
Figure 11. 2 Copy Settings to Other Cameras
2)
Select the camera (s) to be configured with the same OSD settings. You can also check the checkbox of
Analog to select all cameras.
3)
Click the OK button to finish the Copy settings and back to the OSD Configuration interface.
8. Click the Apply button to apply the settings.
157
User Manual of Digital Video Recorder
11.2 Configuring Privacy Mask
Purpose:
You are allowed to configure the four-sided privacy mask zones that cannot be viewed or recorded by the operator.
Steps:
1. Enter the Privacy Mask Settings interface.
Menu &gt; Camera &gt; Privacy Mask
2. Select the camera to set privacy mask.
3. Check the checkbox of Enable Privacy Mask to enable this feature.
Figure 11. 3 Privacy Mask Settings Interface
4. Use the mouse to draw a zone on the window. The zones will be marked with different frame colors.
Up to 4 privacy mask zones can be configured, and the size of each area can be adjusted.
5. The configured privacy mask zones on the window can be cleared by clicking the corresponding Clear
Zone1-4 icons on the right side of the window, or click Clear All to clear all zones.
Figure 11. 4 Set Privacy Mask Area
6. You can click the Copy button to copy the privacy mask settings of the current camera to other cameras.
Please refer to step 7 of Chapter 11.1Configuring OSD Settings.
7. Click the Apply button to save the settings.
158
User Manual of Digital Video Recorder
Chapter 12 DVR Management and
Maintenance
159
User Manual of Digital Video Recorder
12.1 Viewing System Information
12.1.1 Viewing Device Information
Steps:
1. Enter the System Information interface.
Menu &gt; Maintenance &gt; System Info
2. Click the Device Info tab to enter the Device Information menu to view the device name, model, serial No. ,
firmware version and encoding version, as shown in Figure 12. 1.
Figure 12. 1 Device Information Interface
12.1.2 Viewing Camera Information
Steps:
1. Enter the System Information interface.
Menu &gt; Maintenance &gt; System Info
2. Click the Camera tab to enter the Camera Information menu to view the status of each camera, as shown in
Figure 12. 2.
Figure 12. 2 Camera Information Interface
12.1.3 Viewing Record Information
Steps:
1. Enter the System Information interface.
Menu &gt; Maintenance &gt; System Info
2. Click the Record tab to enter the Record Information menu to view the recording status encoding parameters
of each camera, as shown in Figure 12. 3.
160
User Manual of Digital Video Recorder
Figure 12. 3 Record Information Interface
12.1.4 Viewing Alarm Information
This function is only supported by DS-7300HFHI-ST and DS-8100HFHI-ST series DVR.
Steps:
1. Enter the System Information interface.
Menu &gt; Maintenance &gt; System Info
2. Click the Alarm tab to enter the Alarm Information menu to view the alarm information, as shown in Figure
12. 4.
Figure 12. 4 Alarm Information Interface
12.1.5 Viewing Network Information
Steps:
1. Enter the System Information interface.
Menu &gt; Maintenance &gt; System Info
2. Click the Network tab to enter the Network Information menu to view the network information, as shown in
Figure 12. 5.
161
User Manual of Digital Video Recorder
DS-8100HFHI-ST
Other Models
Figure 12. 5 Network Information Interface
12.1.6 Viewing HDD Information
Steps:
1. Enter the System Information interface.
Menu &gt; Maintenance &gt; System Info
2. Click the HDD tab to enter the HDD Information menu to view the HDD status, free space, property, etc., as
shown in Figure 12. 6.
Figure 12. 6 HDD Information Interface
162
User Manual of Digital Video Recorder
12.2 Searching and Exporting Log Files
Purpose:
The operation, alarm, exception and information of the DVR can be stored in log files, which can be viewed and
exported at any time.
Steps:
1. Enter the Log Search interface.
Menu &gt; Maintenance &gt; Log Search
Figure 12. 7 Log Search Interface
2. Set the log search conditions to refine your search, including the Start Time, End Time, Major Type and
Minor Type.
3. Click the Search button to start search log files.
4. The matched log files will be displayed on the list shown below.
Up to 2000 log files can be displayed each time.
Figure 12. 8 Log Search Results
5. You can click the
button of each log or double-click it to view its detailed information, as shown in
Figure 12. 9. And you can also click the
button to view the related video files if available.
163
User Manual of Digital Video Recorder
Figure 12. 9 Log Details
6. If you want to export the log files, click the Export button to enter the Export menu, as shown in Figure 12.
10.
Figure 12. 10 Export Log Files
7. Select the backup device from the dropdown list of Device Name.
8. Click the Export to export the log files to the selected backup device.
You can click the New Folder button to create new folder in the backup device, or click the Format button
to format the backup device before log export.
 Please connect the backup device to DVR before operating log export.
 The log files exported to the backup device are named by exporting time, e.g.,
20110514124841logBack.txt.
164
User Manual of Digital Video Recorder
12.3 Importing/Exporting Configuration Files
Purpose:
The configuration files of the DVR can be exported to local device for backup; and the configuration files of one
DVR can be imported to multiple DVR devices if they are to be configured with the same parameters.
Steps:
1. Enter the Import/Export Configuration File interface.
Menu &gt; Maintenance &gt; Import/Export
Figure 12. 11 Import/Export Config File
2. Click the Export button to export configuration files to the selected local backup device.
3. To import a configuration file, select the file from the selected backup device and click the Import button.
After the import process is completed, you must reboot the DVR.
After having finished the import of configuration files, the device will reboot automatically.
165
User Manual of Digital Video Recorder
12.4 Upgrading System
Purpose:
The firmware on your DVR can be upgraded by local backup device or remote FTP server.
12.4.1 Upgrading by Local Backup Device
Steps:
1. Connect your DVR with a local backup device where the update firmware file is located.
2. Enter the Upgrade interface.
Menu &gt; Maintenance &gt; Upgrade
3. Click the Local Upgrade tab to enter the local upgrade menu, as shown in Figure 12. 12.
Figure 12. 12 Local Upgrade Interface
4. Select the update file from the backup device.
5. Click the Upgrade button to start upgrading.
6. After the upgrading is complete, reboot the DVR to activate the new firmware.
12.4.2 Upgrading by FTP
Before you start:
Configure PC (running FTP server) and DVR to the same Local Area Network. Run the 3rd-party TFTP software
on the PC and copy the firmware into the root directory of TFTP.
Steps:
1. Enter the Upgrade interface.
Menu &gt; Maintenance &gt; Upgrade
2. Click the FTP tab to enter the local upgrade interface, as shown in Figure 12. 13.
Figure 12. 13 FTP Upgrade Interface
3. Enter the FTP Server Address in the text field.
4. Click the Upgrade button to start upgrading.
5. After the upgrading is complete, reboot the DVR to activate the new firmware.
166
User Manual of Digital Video Recorder
12.5 Restoring Default Settings
Steps:
1. Enter the Default interface.
Menu &gt; Maintenance &gt; Default
Figure 12. 14 Restore Factory Default
2. Click the OK button to restore the default settings.
Except the network parameters (including IP address, subnet mask, gateway, MTU, default route and
server port), all other parameters of the device will be restored to factory default settings.
167
User Manual of Digital Video Recorder
Chapter 13 Others
168
User Manual of Digital Video Recorder
13.1 Configuring General Settings
Purpose:
You can configure the output resolution, system time, mouse pointer speed, etc.
Steps:
1. Enter the General Settings interface.
Menu &gt; Configuration &gt; General
2. Select the General tab.
DS-7300HFHI-ST and DS-8100HFHI-ST
Other Models
Figure 13. 1 General Settings Interface
3. Configure the following settings:
• Language: The default language used is English.
• CVBS Output Standard: Select the CVBS output standard to NTSC or PAL, which must be the same
with the video input standard (for DS-7300HFHI-ST and DS-8100HFHI-ST only).
• Resolution: Select the output resolution, which must be the same with the resolution of the monitor
screen.
•
•
•
•
•
•
•
Time Zone: Select the time zone.
Date Format: Select the date format.
System Date: Select the system date.
System Time: Select the system time.
Mouse Pointer Speed: Set the speed of mouse pointer; 4 levels are configurable.
Enable Wizard: Enable/disable the Wizard when the device starts up.
Enable ID Authentication: Enable/disable the use of the login password.
4. Click the Apply button to save the settings.
169
User Manual of Digital Video Recorder
13.2 Configuring DST Settings
Steps:
1. Enter the General Settings interface.
Menu &gt;Configuration&gt;General
2. Choose DST Settings tab.
Figure 13. 2 DST Settings Interface
You can check the checkbox before the Auto DST Adjustment item.
Or you can manually check the Enable DST checkbox, and then you choose the date of the DST period.
170
User Manual of Digital Video Recorder
13.3 Configuring More Settings
Steps:
1. Enter the General Settings interface.
Menu &gt; Configuration &gt; General
2. Click the More Settings tab to enter the More Settings interface, as shown in Figure 13. 3.
DS-7300HFHI-ST and DS-8100HFH-ST
Other Models
Figure 13. 3 More Settings Interface
3. Configure the following settings:
• Device Name: Edit the name of DVR.
• Device No.: Edit the serial number of DVR. The Device No. can be set in the range of 1~255, and the
default No. is 255.
• CVBS Output Brightness: Adjust the video output brightness.
• Operation Timeout: Set timeout time for menu inactivity. E.g., when the timeout time is set to 5
Minutes, then the system will exit from the current operation menu to live view screen after 5 minutes of
menu inactivity.
• Menu Output Mode: You can choose the menu display on different video output. There are auto,
HDMI/VGA and Main CVBS selectable.
4. Click the Apply button to save the settings.
171
User Manual of Digital Video Recorder
13.4 Managing User Accounts
Purpose:
There is a default account in the DVR: Administrator. The Administrator user name is admin and the password is
12345. The Administrator has the permission to add and delete user and configure user parameters.
13.4.1 Adding a User
Steps:
1. Enter the User Management interface.
Menu &gt; Configuration &gt; User
Figure 13. 4 User Management Interface
2. Click the Add button to enter the Add User interface.
Figure 13. 5 Add User Menu
3. Enter the information for new user, including User Name, Password, Level and User’s MAC Address.
Level: Set the user level to Operator or Guest. Different user levels have different operating permission.
• Operator: The Operator user level has permission of Local Log Search in Local Configuration, Remote
Log Search and Two-way Audio in Remote Configuration and all operating permission in Camera
Configuration.
• Guest: The Guest user has permission of Local Log Search in Local Configuration, Remote Log Search
in Remote Configuration and only has the local/remote playback in the Camera Configuration.
User’s MAC Address: The MAC address of the remote PC which logs onto the DVR. If it is configured and
enabled, it only allows the remote user with this MAC address to access the DVR.
4. Click the OK button to save the settings and go back to the User Management interface. The added new user
172
User Manual of Digital Video Recorder
will be displayed on the list, as shown in Figure 13. 6.
Figure 13. 6 Added User Listed in User Management Interface
5. Select the user from the list and then click the
button to enter the Permission settings interface, as shown
in Figure 13. 7.
Figure 13. 7 User Permission Settings Interface
6. Set the operating permission of Local Configuration, Remote Configuration and Camera Configuration for
the user.
Local Configuration
• Local Log Search: Searching and viewing logs and system information of DVR.
• Local Parameters Settings: Configuring parameters, restoring factory default parameters and
importing/exporting configuration files.
• Local Advanced Operation: Operating HDD management (initializing HDD, setting HDD property),
upgrading system firmware, clearing I/O alarm output.
• Local Shutdown Reboot: Shutting down or rebooting the DVR.
Remote Configuration
• Remote Log Search: Remotely viewing logs that are saved on the DVR.
• Remote Parameters Settings: Remotely configuring parameters, restoring factory default parameters and
importing/exporting configuration files.
•
•
•
•
Remote Serial Port Control: Configuring settings for RS-232 and RS-485 ports.
Remote Video Output Control: Sending remote button control signal.
Two-way Audio: Realizing two-way radio between the remote client and the DVR.
Remote Alarm Control: Remotely arming (notify alarm and exception message to the remote client) and
controlling the alarm output.
• Remote Advanced Operation: Remotely operating HDD management (initializing HDD, setting HDD
property), upgrading system firmware, clearing I/O alarm output.
• Remote Shutdown/Reboot: Remotely shutting down or rebooting the DVR.
Camera Configuration
• Remote Live View: Remotely viewing live video of the selected camera(s).
173
User Manual of Digital Video Recorder
• Local Manual Operation: Locally starting/stopping manual recording and alarm output of the selected
camera(s).
• Remote Manual Operation: Remotely starting/stopping manual recording and alarm output of the
selected camera(s).
•
•
•
•
•
Local Playback: Locally playing back recorded files of the selected camera(s).
Remote Playback: Remotely playing back recorded files of the selected camera(s).
Local PTZ Control: Locally controlling PTZ movement of the selected camera(s).
Remote PTZ Control: Remotely controlling PTZ movement of the selected camera(s).
Local Video Export: Locally exporting recorded files of the selected camera(s).
7. Click the OK button to save the settings and exit interface.
Only the admin user account has the permission of restoring factory default parameters.
13.4.2 Deleting a User
Steps:
1. Enter the User Management interface.
Menu &gt; Configuration &gt; User
2. Select the user to be deleted from the list, as shown in Figure 13. 8.
Figure 13. 8 Delete a User
3. Click the
icon to delete the selected user.
13.4.3 Editing a User
Steps:
1. Enter the User Management interface.
Menu &gt; Configuration &gt; User
2. Select the user to be edited from the list, as shown in Figure 13. 9.
Figure 13. 9 Edit a User
3. Click the
icon to enter the Edit User interface, as shown in Figure 13. 10 and Figure 13. 11.
174
User Manual of Digital Video Recorder
Figure 13. 10 Edit User Interface-operator and guest
Figure 13. 11 Edit User Interface-admin
4. Edit the parameters.
• Operator and Guest
You can edit the user information, including user name, password, permission level and MAC address.
Check the checkbox of Change Password if you want to change the password, and input the new one in the
text field of Password and Confirm.
• Admin
You are only allowed to edit password and MAC address. Check the checkbox of Change Password if you
want to change the password, and the input the correct old password, and the new one in the text field of
Password and Confirm.
5. Click the OK button to save the settings and exit the interface.
175
User Manual of Digital Video Recorder
13.5 Logging out/Shutting down/Rebooting
Device
Steps:
1. Enter the Shutdown interface.
Menu &gt; Shutdown
Figure 13. 12 Shutdown Menu
2. Click the Logout button to log out, or
Click the Shutdown button to shut down the device, or
Click the Reboot button to reboot the device.
After you have logged out the system, menu operation on the screen is invalid. It is required a user name
and password to login the system.
176
User Manual of Digital Video Recorder
Chapter 14 Appendix
177
User Manual of Digital Video Recorder
Glossary
• Dual Stream: Dual stream is a technology used to record high resolution video locally while transmitting
a lower resolution stream over the network. The two streams are generated by the DVR, with the main
stream having a maximum resolution of 1080P and the sub-stream having a maximum resolution of CIF.
• DVR: Acronym for Digital Video Recorder. A DVR is device that is able to accept video signals from
analog cameras, compress the signal and store it on its hard drives.
• HDD: Acronym for Hard Disk Drive. A storage medium which stores digitally encoded data on platters
with magnetic surfaces.
• DHCP: Dynamic Host Configuration Protocol (DHCP) is a network application protocol used by devices
(DHCP clients) to obtain configuration information for operation in an Internet Protocol network.
• HTTP: Acronym for Hypertext Transfer Protocol. A protocol to transfer hypertext request and information
between servers and browsers over a network
• PPPoE: PPPoE, Point-to-Point Protocol over Ethernet, is a network protocol for encapsulating
Point-to-Point Protocol (PPP) frames inside Ethernet frames. It is used mainly with ADSL services where
individual users connect to the ADSL transceiver (modem) over Ethernet and in plain Metro Ethernet
networks.
• DDNS: Dynamic DNS is a method, protocol, or network service that provides the capability for a
networked device, such as a router or computer system using the Internet Protocol Suite, to notify a
domain name server to change, in real time (ad-hoc) the active DNS configuration of its configured
hostnames, addresses or other information stored in DNS.
• Hybrid DVR: A hybrid DVR is a combination of a DVR and NVR.
• NTP: Acronym for Network Time Protocol. A protocol designed to synchronize the clocks of computers
over a network.
• NTSC: Acronym for National Television System Committee. NTSC is an analog television standard used
in such countries as the United States and Japan. Each frame of an NTSC signal contains 525 scan lines at
60Hz.
• NVR: Acronym for Network Video Recorder. An NVR can be a PC-based or embedded system used for
centralized management and storage for IP cameras, IP Domes and other DVRs.
• PAL: Acronym for Phase Alternating Line. PAL is also another video standard used in broadcast
televisions systems in large parts of the world. PAL signal contains 625 scan lines at 50Hz.
• PTZ: Acronym for Pan, Tilt, Zoom. PTZ cameras are motor driven systems that allow the camera to pan
left and right, tilt up and down and zoom in and out.
• USB: Acronym for Universal Serial Bus. USB is a plug-and-play serial bus standard to interface devices to
a host computer.
178
User Manual of Digital Video Recorder
Troubleshooting

No image displayed on the monitor after the device is starting up normally.
Possible Reasons:
a) No VGA or HDMI connections.
b) Connection cable is damaged.
c) Input mode of the monitor is incorrect.
Steps:
1. Verify the device is connected with the monitor via HDMI or VGA cable.
If not, please connect the device with the monitor and reboot.
2. Verify the connection cable is good.
If there is still no image display on the monitor after rebooting, please check if the connection cable is
good, and change a cable to connect again.
3. Verify Input mode of the monitor is correct.
Please check the input mode of the monitor matches with the output mode of the device (e.g. if the
output mode of DVR is HDMI output, then the input mode of monitor must be the HDMI input). And if
not, please modify the input mode of monitor.
4. Check if the fault is solved by the step 1 to step 3.
If it is solved, finish the process.
If not, please contact the engineer from our company to do the further process.
 There is a beep sound after a new bought device starts up.
Possible Reasons:
a) No HDD is installed in the device.
b) The installed HDD has not been initialized.
c) The installed HDD is not compatible with the device or is broken-down.
Steps:
1. Verify at least one HDD is installed in the device.
1) If not, please install the compatible HDD.
Please refer to the “Quick Operation Guide” for the HDD installation steps.
2) If you do not want to install a HDD, select “Menu&gt;Configuration &gt; Exceptions”, and uncheck the
Audible Warning checkbox of “HDD Error”.
2. Verify the HDD is initialized.
1) Select “Menu&gt;HDD&gt;General”.
2) If the status of the HDD is “Uninitialized”, please check the checkbox of corresponding HDD and
click the “Init” button.
3. Verify the HDD is detected or is in good condition.
1) Select “Menu&gt;HDD&gt;General”.
2) If the HDD is not detected or the status is “Abnormal”, please replace the dedicated HDD according
to the requirement.
4. Check if the fault is solved by the step 1 to step 3.
1) If it is solved, finish the process.
179
User Manual of Digital Video Recorder
2) If not, please contact the engineer from our company to do the further process.

Live view stuck when video outputs locally.
Possible Reasons:
a) The frame rate has not reached the real-time frame rate.
Steps:
1. Check the parameters of Main Stream (Normal) and Main Stream (Event).
Select “Menu &gt; Record &gt; Encoding &gt; Record”, and set the resolution of Main Stream (Event) the same
as the one of Main Stream (Normal).
2. Verify the frame rate is real-time frame rate.
Select “Menu &gt; Record &gt; Parameters &gt; Record”, and set the Frame rate to Full Frame.
3. Check if the fault is solved by the above steps.
If it is solved, finish the process.
If not, please contact the engineer from our company to do the further process.

When using the device to get the live view audio, there is no sound or there is too much noise, or the
volume is too low.
Possible Reasons:
a) Cable between the pickup and camera is not connected well; impedance mismatches or incompatible.
b) The stream type is not set as “Video &amp; Audio”.
Steps:
1. Verify the cable between the pickup and camera is connected well; impedance matches and compatible.
2. Verify the setting parameters are correct.
Select “Menu &gt; Record &gt; Parameters &gt; Record”, and set the Stream Type as “Audio &amp; Video”.
3. Check if the fault is solved by the above steps.
If it is solved, finish the process.
If not, please contact the engineer from our company to do the further process.

The image gets stuck when DVR is playing back by single or multi-channel cameras.
Possible Reasons:
a) The frame rate is not the real-time frame rate.
b) The DVR supports up to 16-channel synchronize playback at the resolution of 4CIF, if you want a
16-channel synchronize playback at the resolution of 720p, the frame extracting may occur, which leads
to a slight stuck.
Steps:
1. Verify the frame rate is real-time frame rate.
Select “Menu &gt; Record &gt; Parameters &gt; Record”, and set the Frame Rate to “Full Frame”.
2. Verify the hardware can afford the playback.
Reduce the channel number of playback.
Select “Menu &gt; Record &gt; Encoding &gt; Record”, and set the resolution and bitrate to a lower level.
3. Reduce the number of local playback channel.
Select “Menu &gt; Playback”, and uncheck the checkbox of unnecessary channels.
4. Check if the fault is solved by the above steps.
If it is solved, finish the process.
If not, please contact the engineer from our company to do the further process.

No record file found in the device local HDD, and the prompt “No record file found” pops up when you
search the record files.
180
User Manual of Digital Video Recorder
Possible Reasons:
a) The time setting of system is incorrect.
b) The search condition is incorrect.
c) The HDD is error or not detected.
Steps:
1. Verify the system time setting is correct.
Select “Menu &gt; Configuration &gt; General &gt; General”, and verify the “Device Time” is correct.
2. Verify the search condition is correct.
Select “Playback”, and verify the channel and time are correct.
3. Verify the HDD status is normal.
Select “Menu &gt; HDD &gt; General” to view the HDD status, and verify the HDD is detected and can be
read and written normally.
4. Check if the fault is solved by the above steps.
If it is solved, finish the process.
If not, please contact the engineer from our company to do the further process.
0203041031024
181
User Manual of Digital Video Recorder
182
">

Hello! I am an AI chatbot specifically trained to assist you with the Hikvision DS-8108HFHI-ST User manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Assistant typing

Assistant terminated

Related

TVT TD-2304 1UB 数字硬盘录像机 产品说明书

Laview LV-KH94FOLFB5-T1 4-Channel 1TB HDD Indoor/Outdoor Day Night Surveillance System and (4) HD 720P Camera 1 Bonus Channel Remote View User manual

Annke UI Blue) for Soter DVR Series (DW41JD/ DW81KD/ DW61LD DVR User Manual

Hikvision DS-8108HFHI-ST User manual

EFB SP-8HDSET User Manual

eidetic EI-6120 NIP-16, EI-6320-NI2, EI-6320-NIR3 User Manual

Eyeris Digital video recorder User Manual

EasternCCTV TVI Quick Start Guide

Digital Video Recorder LTN7600-HT LTN76/08/16-HT User Manual

Techpro TRIDVR-PRE32C Prime Series Manual

TVT TD-2304 1UB 数字硬盘录像机产品说明书