advertisement
D I G I T A L P I A N O
P I A N O N U M É R I Q U E
P - 1 0 5
Référence MIDI
Table des matières
Sélection du canal de transmission/réception MIDI ...................................... 2
Local Control ON/OFF (Activation/désactivation de la commande locale) ... 2
Format des données MIDI .................................................................. 4
MIDI Implementation Chart................................................................. 8
FR
Fonctions MIDI
Vous pouvez effectuer des réglages détaillés pour les fonctions MIDI.
Sélection du canal de transmission/réception MIDI
Dans toute configuration de commandes MIDI, les canaux MIDI des périphériques de transmission et de réception doivent obligatoirement correspondre entre eux pour que le transfert des données s'effectue correctement.
Ce paramètre sert à spécifier le canal sur lequel l’instrument transmet ou reçoit des données MIDI.
Réglage du canal de transmission
Maintenez la touche [DEMO/SONG] (Démo/Morceau) enfoncée, appuyez sur la touche
[METRONOME/RHYTHM] (Métronome/Rythme) et maintenez-la enfoncée puis appuyez sur une touche comprise entre E0–G #1.
NOTE
En mode Dual, Split ou Duo, les données de la sonorité 1 sont transmises sur le canal spécifié pour cette dernière alors que les données de la sonorité 2 sont transmises via le canal portant le numéro le plus élevé après celui du canal spécifié.
Dans ce cas, aucune donnée ne sera transmise si le canal de transmission est réglé sur « OFF » (Désactivation).
Réglage du canal de réception
Maintenez la touche [DEMO/SONG] enfoncée, appuyez sur la touche [METRONOME/RHYTHM] et maintenez-la enfoncée puis appuyez sur une touche comprise entre A #1–D#3.
G #1 A#1 D #3
NOTE
ALL (Tout) :
Réception « multi-timbre ». Ce réglage autorise la réception simultanée de différentes parties sur les 16 canaux MIDI, ce qui permet à l'instrument de reproduire les données d'un morceau à plusieurs canaux transmises depuis un ordinateur.
1+2:
Réception « 1+2 ». Ce réglage autorise la réception simultanée des canaux 1 et 2 uniquement, ce qui permet à l'instrument de reproduire les données d'un morceau via les canaux 1 et 2 transmises depuis un ordinateur.
E0
3 5 7 10 12 15 OFF 1 4 6 9 11 13 16 ALL
NOTE
Les messages de changement de programme et les messages relatifs aux canaux n'affectent pas les réglages de panneau de l'instrument ni les notes que vous jouez au clavier.
1 2 4 6 8 9 11 13 14 16 2 3 5 7 8 10 12 14 15 1+2
Canal de transmission
(E0–G #1)
Canal de réception
(A #1–D#3)
NOTE
Les données des morceaux de démonstration et des morceaux prédéfinis ne sont pas transmissibles via MIDI.
Local Control ON/OFF (Activation/désactivation de la commande locale)
La fonction « Local Control » (Commande locale) indique que le clavier de cet instrument contrôle en principe lui-même son générateur de sons interne, ce qui lui permet de reproduire les sonorités internes directement depuis le clavier. C'est le cas en mode
« Local Control On » (Commande locale activée), puisque le générateur de sons interne est alors contrôlé localement par son propre clavier. Cependant, il est possible de désactiver la commande locale (OFF) de sorte que le clavier de l'instrument ne reproduise pas les sonorités internes mais que les informations MIDI appropriées continuent d'être transmises via la borne [USB TO HOST] (USB vers
Hôte) lorsque des notes sont jouées au clavier. Dans le même temps, le générateur de sons interne réagit aux informations MIDI reçues via la borne [USB TO HOST].
Maintenez la touche [DEMO/SONG] enfoncée, appuyez sur la touche [METRONOME/RHYTHM] et maintenez-la enfoncée puis appuyez sur la touche D6. Appuyez plusieurs fois sur la touche D6 pour basculer entre les états d'activation et de désactivation de Local Control.
NOTE
Réglage par défaut : ON (Activation)
D6
2
P-105 Référence MIDI
Fonctions MIDI
Program Change ON/OFF (Activation/désactivation du changement de programme)
L'instrument réagit habituellement aux numéros de changement de programme MIDI reçus d'un ordinateur, ce qui entraîne la sélection du même numéro de sonorité sur le canal correspondant (la sonorité du clavier reste inchangée). En règle générale, l'instrument envoie
également un numéro de changement de programme MIDI dès lors que l'une de ses sonorités est sélectionnée, ce qui entraîne la sélection du même numéro de sonorité ou de programme sur l'ordinateur lorsque celui-ci est configuré pour recevoir des numéros de changement de programme MIDI et pour y répondre. Cette fonction permet d'annuler la réception et la transmission d'un numéro de changement de programme de manière à sélectionner les sonorités de l'instrument sans que cela affecte l'ordinateur.
Maintenez la touche [DEMO/SONG] enfoncée, appuyez sur la touche [METRONOME/RHYTHM] et maintenez-la enfoncée puis appuyez sur la touche D #6. Appuyez plusieurs fois sur la touche D#6 pour basculer entre l'activation et la désactivation de Program Change (Changement de programme)..
D #6
NOTE
Pour plus d'informations sur les numéros de changement de programme de chacune des sonorités de l'instrument,
NOTE
Réglage par défaut : ON
Control Change ON/OFF (Activation/désactivation du changement de commande)
En général, l'instrument répond aux données de changement de commande MIDI reçues depuis un ordinateur, de sorte que la sonorité du canal correspondant est affectée par les réglages de la pédale et des autres « commandes » provenant du périphérique de commande
(la sonorité de clavier n'est pas concernée). L'instrument transmet également des informations de changement de commande MIDI lorsque la pédale ou d'autres commandes appropriées sont actionnées. Cette fonction permet d'annuler la réception et la transmission des données de changement de commande de manière à pouvoir, par exemple, actionner la pédale ou d'autres commandes de l'instrument sans que l'ordinateur en soit affecté.
Maintenez la touche [DEMO/SONG] enfoncée, appuyez sur la touche [METRONOME/RHYTHM] et maintenez-la enfoncée puis appuyez sur la touche E6. Appuyez plusieurs fois sur la touche E6 pour basculer entre l'activation et la désactivation de Control Change (Changement de commande).
E6
NOTE
Pour plus d'informations sur les changements de commande pouvant être utilisés avec l'instrument, reportez-vous à
NOTE
Réglage par défaut : ON
P-105 Référence MIDI
3
MIDI Data Format / MIDI-Datenformat /
Format des données MIDI / Formato de datos MIDI
1. NOTE ON/OFF
Data format: [9nH] -> [kk] -> [vv]
9nH = Note ON/OFF event (n = channel number) kk = Note number (Transmit: 09H–78H = A-2–C8 /
Receive: 00H–7FH = C-2–G8) vv = Velocity (Key ON = 01H–7FH, Key OFF = 00H)
Data format: [8nH] -> [kk] -> [vv] (reception only)
8nH = Note OFF event (n = channel number) kk = Note number: 00H–7FH = C-2–G8 vv = Velocity
2. CONTROL CHANGE
Data format: [BnH] -> [cc] -> [vv]
BnH = Control change (n = channel number) cc = Control number vv = Data Range
(1) Bank Select ccH
00H
20H
Parameter
Bank Select MSB
Bank Select LSB
Data Range (vvH)
00H:Normal
00H...7FH
Bank selection processing does not occur until receipt of next
Program Change message.
(2) Modulation (reception only) ccH Parameter Data Range (vvH)
01H Modulation 00H...7FH
(3) Main Volume ccH Parameter
07H Volume MSB
Data Range (vvH)
00H...7FH
(4) Panpot (reception only) ccH Parameter
0AH Panpot
(5) Expression ccH Parameter
0BH Expression MSB
(6) Damper Pedal/Sustain ccH Parameter
40H Sustain MSB
(7) Sostenuto ccH Parameter
42H Sostenuto
(8) Soft Pedal ccH Parameter
Data Range (vvH)
00H...7FH
Data Range (vvH)
00H...7FH
Data Range (vvH)
00H...7FH
Data Range (vvH)
(9) Harmonic Content (reception only) ccH Parameter
47H Harmonic Content 00H...7FH
(10) Release Time (reception only) ccH Parameter
48H Release Time 00H...7FH
(11) Attack Time (reception only) ccH Parameter
49H Attack Time 00H...7FH
(12) Brightness (reception only) ccH Parameter
4AH Brightness 00H...7FH
(13) Portamento Control (reception only) ccH Parameter
54H Portamento 00H...7FH
(14) Effect1 Depth (Reverb Send Level) ccH Parameter Data Range (vvH)
5BH Effect1 Depth 00H...7FH
Adjusts the reverb send level.
(15) Effect3 Depth (Chorus Send Level) ccH Parameter Data Range (vvH)
5DH Effect3 Depth 00H...7FH
(16) RPN
65H RPN
64H RPN
06H Data Entry
26H Data Entry
60H Data
MSB
LSB
MSB
LSB
Increment
61H Data Decrement
* Parameters that are controllable with RPN:
• Coarse Tune
• Fine Tune
• Pitch Bend Range
3. MODE MESSAGES
Data format: [BnH] -> [cc] -> [vv]
BnH = Control event (n = channel number) cc = Control number vv = Data Range
(1) All Sound Off (reception only) ccH Parameter
78H All Sound Off
Data Range (vvH)
00H
(2) Reset All Controllers (reception only) ccH Parameter Data Range (vvH)
79H Reset All Controllers 00H
Resets controllers as follows.
Controller Value
Expression 127 (max)
Sostenuto
Soft Pedal
0 (off)
0 (off)
(3) Local Control (reception only) ccH Parameter Data Range (vvH)
7AH Local Control 00H (off), 7FH (on)
(4) All Notes Off (reception only) ccH Parameter
7BH All Notes Off
Data Range (vvH)
00H
Switches OFF all the notes that are currently ON on the specified channel. Any notes being held by the sustain or sostenuto pedal will continue to sound until the pedal is released.
(5) Omni Off (reception only) ccH
7CH
Parameter
Omni Off
Data Range (vvH)
00H
Same processing as for All Notes Off.
(6) Omni On (reception only) ccH
7DH
Parameter
Omni On
Data Range (vvH)
00H
Same processing as for All Notes Off.
(7) Mono (reception only) ccH Parameter Data Range (vvH)
7EH Mono 00H
Same processing as for All Sound Off.
(8) Poly (reception only) ccH
7FH
Parameter
Poly
Data Range (vvH)
00H
Same processing as for All Sound Off.
• When Control Change is turned OFF, Control Change messages will not be transmitted or received.
• Local on/off, OMNI on/off are not transmitted. (The appropriate note off number is supplied with “All Note Off” transmission).
• When a voice bank MSB/LSB is received, the number is stored in the internal buffer regardless of the received order, then the stored value is used to select the appropriate voice when a program change message is received.
• Poly mode is always active. This mode will not change when the instrument receives a MONO/POLY mode message.
4
P-105 MIDI Reference / MIDI-Referenz / Référence MIDI / Referencia MIDI
MIDI Data Format / MIDI-Datenformat / Format des données MIDI / Formato de datos MIDI
4. PROGRAM CHANGE
Data format: [CnH] -> [ppH]
CnH = Program event (n = channel number) ppH = Program change number
P.C.#=Program Change number
Voice Name
GRAND PIANO 1
GRAND PIANO 2
E. PIANO 1
E. PIANO 2
E. PIANO 3
E. PIANO 4
JAZZ ORGAN
PIPE ORGAN
ROCK ORGAN
VIBRAPHONE
STRINGS
HARPSICHORD
WOOD BASS
E. BASS
MSB
0
0
0
0
0
0
0
0
0
0
0
0
0
0
LSB
122
112
122
123
122
123
122
123
122
122
122
122
122
122
P.C.#
1
1
6
6
5
5
17
20
19
12
49
7
33
34
• When program change reception is turned OFF, no program change data is transmitted or received.
• When you specify a program change as a number in the range of
0–127, specify a number that is one less than the program change number listed above. For example, to specify program change number 1, you would specify a value of 0.
5. Pitch Bend Change (reception only)
[EnH] -> [ccH] -> [ddH] ccH = LSB ddH = MSB
6. SYSTEM REALTIME MESSAGES
[rrH]
F8H: Timing clock
FAH: Start
FCH: Stop
FEH: Active sensing
Data
F8H
FAH
FCH
FEH
Transmission
Transmitted every
96 clocks
Song start
Song stop
Transmitted every
200 milliseconds
Reception
Received as 96-clock tempo timing when MIDI clock is set to
External.
Song start
Not received when the MIDI clock is set to Internal.
Song stop
Not received when the MIDI clock is set to Internal.
If a signal is not received via MIDI for more than 400 milliseconds, the same processing will take place for All Sound Off, All Notes
Off and Reset All Controllers as when those signals are received.
• If an error occurs during MIDI reception, the Sustain, Sostenuto, and Soft effects for all channels are turned off and an All Note Off occurs.
7. SYSTEM EXCLUSIVE MESSAGES
(Universal System Exclusive)
(1) Universal Realtime Message
Data format: [F0H] -> [7FH] -> [XnH] -> [04H] -> [01H] -> [ llH] ->
[mmH] -> [F7H]
MIDI Master Volume (reception only)
• Simultaneously changes the volume of all channels.
• When a MIDI master volume message is received, the volume only has affect on the MIDI receive channel, not the panel master volume.
F0H = Exclusive status
7FH = Universal Realtime
7FH = ID of target device
04H = Sub-ID #1=Device Control Message
01H = Sub-ID #2=Master Volume
llH = Volume LSB mmH = Volume MSB
F7H = End of Exclusive
or
F0H = Exclusive status
7FH = Universal Realtime
XnH = When received, n=0–F.
X = irrelevant
04H = Sub-ID #1=Device Control Message
01H = Sub-ID #2=Master Volume
llH = Volume LSB mmH = Volume MSB
F7H = End of Exclusive
(2) Universal Non-Realtime Message (GM On)
General MIDI Mode On
Data format: [F0H] -> [7EH] -> [XnH] -> [09H] -> [01H] -> [F7H]
F0H = Exclusive status
7EH = Universal Non-Realtime
7FH = ID of target device
09H = Sub-ID #1=General MIDI Message
01H = Sub-ID #2=General MIDI On
F7H = End of Exclusive
or
F0H = Exclusive status
7EH = Universal Non-Realtime
XnH = When received, n=0–F.
X = irrelevant
09H = Sub-ID #1=General MIDI Message
01H = Sub-ID #2=General MIDI On
F7H = End of Exclusive
When the General MIDI mode ON message is received, the MIDI system will be reset to its default settings.
This message requires approximately 50ms to execute, so sufficient time should be allowed before the next message is sent.
P-105 MIDI Reference / MIDI-Referenz / Référence MIDI / Referencia MIDI
5
MIDI Data Format / MIDI-Datenformat / Format des données MIDI / Formato de datos MIDI
8. SYSTEM EXCLUSIVE MESSAGES (XG Standard)
(1) XG Native Parameter Change
Data format: [F0H] -> [43H] -> [1nH] -> [4CH] -> [hhH] -> [mmH] ->
[ llH] -> [ddH] -> [F7H]
F0H = Exclusive status
43H = YAMAHA ID
1nH = When received, n=0–F.
When transmitted, n=0.
4CH = Model ID of XG hhH = Address High mmH = Address Mid
llH = Address Low ddH = Data
|
F7H = End of Exclusive
Data size must match parameter size (2 or 4 bytes).
When the XG System On message is received, the MIDI system will be reset to its default settings.
The message requires approximately 50ms to execute, so sufficient time should be allowed before the next message is sent.
(2) XG Native Bulk Data (reception only)
Data format: [F0H] -> [43H] -> [0nH] -> [4CH] -> [aaH] -> [bbH] ->
[hhH] -> [mmH] -> [
llH] ->[ddH] ->...-> [ccH] -> [F7H]
F0H = Exclusive status
43H = YAMAHA ID
0nH = When received, n=0–F.
When transmitted, n=0.
4CH = Model ID of XG aaH = ByteCount bbH = ByteCount hhH = Address High mmH = Address Mid
llH = Address Low ddH = Data
| |
| | ccH = Check sum
F7H = End of Exclusive
• Receipt of the XG SYSTEM ON message causes reinitialization of relevant parameters and Control Change values. Allow sufficient time for processing to execute (about 50 msec) before sending the instrument another message.
• XG Native Parameter Change message may contain two or four bytes of parameter data (depending on the parameter size).
• For information about the Address and Byte Count values, refer to
Table 1 below. Note that the table’s Total Size value gives the size of a bulk block. Only the top address of the block (00H, 00H, 00H) is valid as a bulk data address.
9. SYSTEM EXCLUSIVE MESSAGES
(Digital Piano MIDI Format)
Data format: [F0H] -> [43H] -> [73H] -> [xxH] -> [nnH] -> [F7H]
F0H = Exclusive status
43H = Yamaha ID
73H = Digital Piano ID
01H = Product ID (digital piano common) xxH = Substatus nn control
02H Internal MIDI clock
03H External MIDI clock
F7H = End of Exclusive
10. SYSTEM EXCLUSIVE MESSAGES (Others)
Data format: [F0H] -> [43H] -> [1nH] -> [27H] -> [30H] -> [00H] ->
[00H] -> [mmH] -> [
llH] -> [ccH] -> [F7H]
Master Tuning (XG and last message priority) simultaneously changes the pitch of all channels.
F0H = Exclusive Status
43H = Yamaha ID
1nH = When received, n=0–F.
When transmitted, n=0.
27H =
30H = Sub ID
00H =
00H = mmH = Master Tune MSB
llH = Master Tune LSB ccH = irrelevant (under 7FH)
F7H = End of Exclusive
6
P-105 MIDI Reference / MIDI-Referenz / Référence MIDI / Referencia MIDI
MIDI Data Format / MIDI-Datenformat / Format des données MIDI / Formato de datos MIDI
<Table 1>
MIDI Parameter Change table (SYSTEM)
Address (H) Size (H)
00 00 00
01
02
03
4
Data (H)
020C–05F4(*1)
Parameter
MASTER TUNE
Description
-102.4–+102.3[cent]
1st bit 3–0 bit 15–12
2nd bit 3–0 bit 11–8
3rd bit 3–0 bit 7–4
4th bit 3–0 bit 3–0
0–127 04 1 00–7F MASTER VOLUME
7E
7F
00
00
XG SYSTEM ON 00=XG sytem ON
RESET ALL PARAMETERS 00=ON (receive only)
TOTAL SIZE 07
*1: Values lower than 020CH select -102.4 cents. Values higher than 05F4H select +102.3 cents.
<Table 2>
MIDI Parameter Change table (EFFECT 1)
Refer to the “Effect MIDI Map” for a complete list of Reverb and Chorus type numbers.
Address (H) Size (H)
02 01 00 2
20
22
24
2
1
1
Data (H)
00–7F
00–7F
00–7F
00–7F
00–7F
00–7F
Parameter
REVERB TYPE MSB
REVERB TYPE LSB
CHORUS TYPE MSB
CHORUS TYPE LSB
CHORUS PARAMETER 1
CHORUS PARAMETER 3
Description
Refer to Effect MIDI Map
00 : basic type
Refer to Effect MIDI Map
00 : basic type
<Table 3>
MIDI Parameter Change table (MULTI PART)
Address (H) Size (H) Data (H)
08 nn 11
0C
1
1
00–7F
00–7F
0D 1 nn = Part Number
00–7F
• Effect MIDI Map
REVERB
ROOM
HALL 1
HALL 2
STAGE
OFF
MSB
02H
01H
01H
03H
00H
LSB
10H
10H
11H
10H
00H
Parameter
DRY LEVEL
Description
0–127
VELOCITY SENSE DEPTH 0–127
VELOCITY SENSE OFFSET 0–127
EFFECT
CHORUS
MSB
41H
PHASER 48H
TREMOLO 77H
ROTARY SP 42H
OFF 00H
LSB
08H
11H
00H
12H
00H
Default value (H)
00 04 00 00
400
7F
Default value (H)
01 (=HALL1)
00
41 (=CHORUS1)
00
Default value (H)
7F
40
40
P-105 MIDI Reference / MIDI-Referenz / Référence MIDI / Referencia MIDI
7
MIDI Implementation Chart / MIDI-Implementationstabelle /
MIDI Implementation Chart / Gráfico de implementación MIDI
YAMAHA [ Digital Piano ]
Model P-105 MIDI Implementation Chart
Transmitted Recognized
Function...
Basic
Channel
Default
Changed
1 - 16 o
1 - 16 o
Mode
Default
Messages
Altered
3 x
**************
3 x x
Date :27-JAN-2012
Version : 1.0
Remarks
Note
Number : True voice
Velocity Note ON
Note OFF
0 - 127
************** o 9nH,v=1-127 x 9nH,v=0
0 - 127
0 - 127 o 9nH,v=1-127 x
After
Touch
Key's
Ch's
Pitch Bend
Control
Change
0,32
1
7
10
11
6,38
64,66,67
71-74
84
91
93
96-97
100-101
Prog
Change : True #
System Exclusive x x x *1 o x x o o o x o x *1 o o o x *1 o 0 - 127
************** o x x o 0 - 24 semi o o o o o o o o o o o o o o 0 - 127
Bank Select
Modulation
Main Volume
Panpot
Expression
Data Entry
Pedal
Portament Control
Reverb Depth
Chorus Depth
RPN Inc,Dec
RPN LSB,MSB
: Song Pos.
Common : Song Sel.
: Tune x x x o x x x
System : Clock
Real Time : Commands
: All Sound Off
Aux : Reset All Cntrls
: Local ON/OFF
Mes- : All Notes OFF sages: Active Sense
: Reset
Notes: o o x x x x o o o (120,126,127) o (121) o (123-125) x
*1 These function are not transmitted by panel operation.
It may be transmitted during a Song performance.
Mode 1 : OMNI ON , POLY Mode 2 : OMNI ON ,MONO
Mode 3 : OMNI OFF, POLY Mode 4 : OMNI OFF,MONO o : Yes x : No
U.R.G., Digital Musical Instruments Division
©2012 Yamaha Corporation
209PO-A0
8
P-105 MIDI Reference / MIDI-Referenz / Référence MIDI / Referencia MIDI
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 2 Fonctions MIDI
- 2 Sélection du canal de transmission/réception MIDI
- 2 Local Control ON/OFF (Activation/désactivation de la commande locale)
- 3 Program Change ON/OFF (Activation/désactivation du changement de programme)
- 3 Control Change ON/OFF (Activation/désactivation du changement de commande)
- 8 MIDI Implementation Chart / MIDI-Implementationstabelle / MIDI Implementation Chart / Gráfico de implementación MIDI
- 4 MIDI Data Format / MIDI-Datenformat / Format des données MIDI / Formato de datos MIDI