Advertisement
Advertisement
User manual SyncMaster S23B550V S27B550V The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance. BN46-00193A-02 Before Using the Product Copyright The contents of this manual are subject to change without notice to improve quality. © 2011 Samsung Electronics Samsung Electronics owns the copyright for this manual. Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited. The SAMSUNG and SyncMaster logos are registered trademarks of Samsung Electronics. Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation. VESA, DPM and DDC are registered trademarks of the Video Electronics Standards Association. An administration fee may be charged if either (a) an engineer is called out at your request and there is no defect in the product (i.e. where you have failed to read this user manual). (b) you bring the unit to a repair center and there is no defect in the product (i.e. where you have failed to read this user manual). The amount of such administration charge will be advised to you before any work or home visit is carried out. Icons used in this manual The following images are for reference only. Real-life situations may differ from what is shown in the images. Symbols for safety precautions Warning A serious or fatal injury may result if instructions are not followed. Caution Personal injury or damage to properties may result if instructions are not followed. Activities marked by this symbol are prohibited. Instructions marked by this symbol must be followed. Before Using the Product 2 Before Using the Product Cleaning Cleaning Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched. Take the following steps when cleaning. 1. Power off the monitor and computer. 2. Disconnect the power cord from the monitor. Hold the power cable by the plug and do not touch the cable with wet hands. Otherwise, an electric shock may result. 3. Wipe the monitor screen using a clean, soft and dry cloth. Do not apply a cleaning agent that contains alcohol, solvent, or surfactant to the monitor. ! Do not spray water or detergent directly on the product. 4. Wet a soft and dry cloth in water and wring thoroughly to clean the exterior of the monitor. 5. Connect the power cord to the product after cleaning the product. 6. Power on the monitor and computer. ! Before Using the Product 3 Before Using the Product Securing the Installation Space Ensure some space around the product for ventilation. An internal temperature rise may cause fire and damage the product. Be sure to allow the amount of space as shown below or greater when installing the product. The exterior may differ depending on the product. 10 cm(3.93 inches) 10 cm(3.93 inches) 10 cm (3.93 inches) 10 cm (3.93 inches) 10 cm(3.93 inches) Precautions for storage Be sure to contact Samsung Customer Service Center (page 85) if the inside of the monitor needs cleaning. (Service fee will be charged.) Before Using the Product 4 Before Using the Product Safety Precautions Electricity and Safety The following images are for reference only. Real-life situations may differ from what is shown in the images. Warning Do not use a damaged power cord or plug, or a loose power socket. An electric shock or fire may result. Do not plug many products into the same power socket. Otherwise, the socket may overheat and cause a fire. Do not touch the power plug with wet hands. Otherwise, an electric shock may result. Insert the power plug all the way in so it is not loose. An unstable connection may cause a fire. ! Ensure you connect the power plug to a grounded power socket. (type 1 insulated devices only). ! An electric shock or injury may result. Do not bend or pull the power cord with force. Do not weigh the power cord down with a heavy object. A damaged power cord may cause an electric shock or fire. Do not place the power cord or product near heat sources. An electric shock or fire may result. Remove foreign substances such as dust around the plug pins and power socket with a dry cloth. ! Otherwise, a fire may result. Before Using the Product 5 Before Using the Product Caution Do not unplug the power cord when the product is in use. The product may become damaged by an electric shock. Do not use the power cord for products other than authorized products supplied by Samsung. ! An electric shock or fire may result. Keep the power socket where the power cord is connected unobstructed. If any problem occurs in the product, unplug the power cable to completely cut the power to the product. ! Power to the product cannot be completely cut off with the power button. Hold the plug when disconnecting the power cord from the power socket. An electric shock or fire may result. ! Installation and Safety Warning DO NOT PLACE CANDLES, INSECT REPELLANTS OR CIGARETTES ON TOP OF THE PRODUCT. DO NOT INSTALL THE PRODUCT NEAR HEAT SOURCES. Otherwise, a fire may result. Avoid installing the product in a narrow space with bad ventilation, such as a bookshelf or wall closet. Otherwise, a fire may result due to an increased internal temperature. Keep the plastic packaging bag for the product in a place that cannot be reached by children. ! Children may suffocate. Before Using the Product 6 Before Using the Product Do not install the product on an unstable or vibrating surface (insecure shelf, sloped surface, etc.). The product may fall and break or cause a personal injury. Using the product in an area with excess vibration may damage the product or cause a fire. Do not install the product in a vehicle or a place exposed to dust, moisture (water drips, etc.), oil, or smoke. ! An electric shock or fire may result. Do not expose the product to direct sunlight, heat, or a hot object such as a stove. Otherwise, the product lifespan may be reduced, or a fire may result. Do not install the product within the reach of young children. The product may fall and injure children. Edible oil, such as soybean oil, can damage or deform the product. Do not install the product in a kitchen or near a kitchen counter. Caution Take care not to drop the product when moving it. Otherwise, product failure or personal injury may result. ! Do not set down the product on its front. The screen may become damaged. When installing the product on a cabinet or shelf, make sure that the bottom edge of the front of the product is not protruding. The product may fall and break or cause a personal injury. Install the product only on cabinets or shelves of the right size. Before Using the Product 7 Before Using the Product Put down the product carefully. The product may fall and break or cause a personal injury. ! SAMSUNG ! Installing the product in an unusual place (a place exposed to a lot of fine particles, chemical substances or extreme temperatures, or an airport or train station where the product should operate continuously for an extended period of time) may seriously affect its performance. Be sure to consult Samsung Customer Service Center (page 85) before installation if you want to install the product at such a place. Operation and Safety Warning High voltage runs through the product. Do not attempt to disassemble, repair, or modify the product on your own. An electric shock or fire may result. Contact Samsung Customer Service Center (page 85) for repair. Before you move the product, be sure to turn off the power switch and remove all the cables connected to the product, including the power cord and the antenna cable. ! Otherwise, the power cord may be damaged and a fire or electric shock may result. If the product generates a strange noise, a burning smell, or smoke, remove the power cord immediately and contact Samsung Customer Service Center (page 85). ! An electric shock or fire may result. Do not let children hang from the product or climb on top of it. The product may fall, and your child may become injured or seriously harmed. If the product falls or the exterior is damaged, power off the product, remove the power cord, and contact Samsung Customer Service Center (page 85). Otherwise, an electric shock or fire may result. Before Using the Product 8 Before Using the Product Do not put a heavy object, toy, or sweets on top of the product. The product or heavy objects may fall as children try to reach for the toy or sweets resulting in a serious injury. During a lightning or thunderstorm, remove the power cord and do not touch the antenna cable. ! An electric shock or fire may result. Do not drop objects on the product or apply impact. An electric shock or fire may result. ! Do not move the product by pulling the power cord or any cable. Otherwise, the cable may be damaged and product failure, an electric shock or fire may result. If a gas leakage is found, do not touch the product or power plug. Also, ventilate the area immediately. ! GAS Sparks can cause an explosion or fire. During a lightning or thunderstorm, do not touch the power cord or antenna cable. Do not lift or move the product by pulling the power cord or any cable. Otherwise, the cable may be damaged and product failure, an electric shock or fire may result. Do not use or keep combustible spray or an inflammable substance near the product. ! An explosion or fire may result. Ensure the vents are not blocked by tablecloths or curtains. Otherwise, a fire may result from an increased internal temperature. Before Using the Product 9 Before Using the Product 100 Do not insert a metallic object (a chopstick, coin, hair pin, etc.) or inflammable object (paper, match, etc.) into the vent or ports of the product. If water or any foreign substance enters the product, be sure to power off the product, remove the power cord, and contact Samsung Customer Service Center (page 85). Product failure, an electric shock or fire may result. Do not place objects containing liquid (vases, pots, bottles, etc) or metallic objects on top of the product. If water or any foreign substance enters the product, be sure to power off the product, remove the power cord, and contact Samsung Customer Service Center (page 85). Product failure, an electric shock or fire may result. Caution Leaving the screen fixed on a stationary image for an extended period of time may cause afterimage burn-in or defective pixels. ! If you are not going to use the product for an extended period of time, activate power-saving mode or a moving-picture screen saver. -_! Disconnect the power cord from the power socket if you do not plan on using the product for an extended period of time (vacation, etc.). Otherwise, a fire may result from accumulated dust, overheating, an electric shock, or electric leakage. Use the product at the recommended resolution and frequency. Your eyesight may deteriorate. ! Do not put DC power adapters together. Otherwise, a fire may result. Remove the plastic bag from the DC power adapter before you use it. Otherwise, a fire may result. Before Using the Product 10 Before Using the Product Do not let water enter the DC power adapter or get the adapter wet. An electric shock or fire may result. Avoid using the product outdoors where it can be exposed to rain or snow. Be careful not to get the DC power adapter wet when you wash the floor. Do not put the DC power adapter near to any heating apparatus. Otherwise, a fire may result. Keep the DC power adapter in a well-ventilated area. ! Looking at the screen too close for an extended period of time can deteriorate your eyesight. ! Do not hold the monitor upside-down or move it by holding the stand. The product may fall and break or cause a personal injury. Do not use humidifiers or stoves around the product. An electric shock or fire may result. Rest your eyes for more than 5 minutes for every 1 hour of product use. Eye fatigue will be relieved. ! Do not touch the screen when the product has been turned on for an extended period of time as it will become hot. Store the small accessories used with the product out of reach of children. ! Exercise caution when adjusting the product angle or stand height. ! Otherwise, children's fingers or hands may become stuck and injured. Tilting the product excessively may cause it to fall and result in personal injury. Before Using the Product 11 Before Using the Product Do not place heavy objects on the product. Product failure or personal injure may result. When using headphones or earphones, do not turn the volume too high. Having the sound too loud may damage your hearing. Correct posture to use the product Use the product in the correct posture as follows. Straighten your back. Allow a distance of 45 to 50cm between your eye and the screen, and look slightly downward at the screen. Keep your eyes directly in front of the screen. Adjust the angle so light does not reflect on the screen. Keep your forearms perpendicular to your upper arms and level with the back of your hands. Keep your elbows at about a right angle. Adjust the height of the product so you can keep your knees bent at 90 degrees or more, your heels attached to the floor, and your arms lower than your heart. Before Using the Product 12 Table Of Contents BEFORE USING THE PRODUCT PREPARATIONS USING "MHL(MOBILE HIGH-DEFINITION LINK)" 2 Copyright 2 2 Icons used in this manual Symbols for safety precautions 3 Cleaning 3 4 4 Cleaning Securing the Installation Space Precautions for storage 5 Safety Precautions 5 6 8 Electricity and Safety Installation and Safety Operation and Safety 12 Correct posture to use the product 18 Checking the Contents 18 19 Removing the Packaging Checking the Components 20 Parts 20 22 Frontal Buttons Reverse Side 23 Installation 23 24 25 26 Attaching the Stand Adjusting the Product Tilt Installing a Wall-mount Kit or Desktop Stand Anti-theft Lock 27 "MHL" (Mobile High-Definition Link) 28 30 Using "MHL" Disabling "MHL" Table Of Contents 13 Table Of Contents CONNECTING AND USING A SOURCE DEVICE SCREEN SETUP 31 Before Connecting 31 Pre-connection Checkpoints 31 Connecting the Power 32 Connecting and Using a PC 32 33 34 35 36 Connecting to a PC Connecting to Headphones or Speakers Driver Installation Setting Optimum Resolution Changing the Resolution Using a PC 39 Brightness 39 Configuring Brightness 40 Contrast 40 Configuring Contrast 41 Sharpness 41 Configuring Sharpness 42 SAMSUNG MAGIC Bright 42 Configuring SAMSUNG MAGIC Bright 44 SAMSUNG MAGIC Angle 44 Configuring SAMSUNG MAGIC Angle 45 Coarse 45 Adjusting Coarse 46 Fine 46 Adjusting Fine 47 Response Time 47 Configuring Response Time 48 HDMI Black Level 48 Configuring the HDMI Black Level Settings Table Of Contents 14 Table Of Contents CONFIGURING TINT RESIZING OR RELOCATING THE SCREEN SETUP AND RESET 49 SAMSUNG MAGIC Color 49 Configuring SAMSUNG MAGIC Color 50 Red 50 Configuring Red 51 Green 51 Configuring Green 52 Blue 52 Configuring Blue 53 Color Tone 53 Configuring the Color Tone Settings 54 Gamma 54 Configuring Gamma 55 H-Position & V-Position 55 Configuring H-Position & V-Position 56 Image Size 56 Changing the Image Size 57 Menu H-Position & Menu V-Position 57 Configuring Menu H-Position & Menu VPosition 58 Reset 58 Initializing Settings (Reset) 59 Language 59 Changing the Language 60 Eco Saving 60 Configuring Eco Saving 61 Off Timer On/Off 61 Configuring Off Timer On/Off Table Of Contents 15 Table Of Contents INFORMATION MENU AND OTHERS INSTALLING THE SOFTWARE 62 Off Timer Setting 62 Configuring Off Timer Setting 63 PC/AV Mode 63 Configuring PC/AV Mode 64 Key Repeat Time 64 Configuring Key Repeat Time 65 Auto Source 65 Configuring Auto Source 66 Display Time 66 Configuring Display Time 67 Menu Transparency 67 Changing Menu Transparency 68 INFORMATION 68 Displaying INFORMATION 68 Configuring Volume in the Initial Screen 68 69 Volume Sound Mode 70 Magic Tune 70 70 71 What is MagicTune? Installing the Software Removing the Software 72 MultiScreen 72 73 Installing the Software Removing the Software Table Of Contents 16 Table Of Contents TROUBLESHOOTI NG GUIDE SPECIFICATIONS APPENDIX 74 Requirements Before Contacting Samsung Customer Service Center 74 74 74 Testing the Product Checking the Resolution and Frequency Check the following. 77 Q&A 79 General 81 PowerSaver 82 Standard Signal Mode Table 85 Contact SAMSUNG WORLDWIDE 90 Correct Disposal 90 Correct Disposal of This Product (Waste Electrical & Electronic Equipment) 91 Terminology Table Of Contents 17 1 1.1 Preparations Checking the Contents 1.1.1 Removing the Packaging 1 Open the packaging box. Be careful not to damage the product when you open the packaging with a sharp instrument. 2 Remove the styrofoam from the product. 3 Check the components and remove the styrofoam and plastic bag. This image is for reference only. 4 Store the box in a dry area so that it can be used when moving the product in the future. 1 Preparations 18 1 Preparations 1.1.2 Checking the Components Contact the dealer from whom you purchased the product if any item is missing. The appearance of the components and items sold separately may differ from the image shown. Components Quick setup guide Warranty card (Not available in some locations) User manual Power cable DC power adapter D-SUB cable (optional) Stereo Cable HDMI cable (optional) MHL Cable HDMI-DVI cable (optional) Stand Stand Connector Components may vary depending on the country. 1 Preparations 19 1 1.2 Preparations Parts 1.2.1 Frontal Buttons The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. Key Guide MHL VOL MHL AUTO VOL AUTO This is a touch-type button. Tap the button lightly with a finger. Icons Description MENU Open or close the onscreen display (OSD) menu, or return to the parent menu. OSD control lock: Maintain the current settings, or lock the OSD control to prevent unintended changes to settings. Enable: To lock the OSD control, press the [ MENU ] button for 10 seconds. Disable: To unlock the locked OSD control, press the [ MENU ] button for more than 10 seconds. If the OSD control is locked, MHL SAMSUNG Brightness and Contrast, MAGIC Bright can be adjusted, and INFORMATION can be viewed. Pressing the [MHL] button when your smartphone is connected to [HDMI 2 / MHL] on the product enables the MHL function, which allows you to import data from the smartphone to the product. For further details on the MHL function, refer to " Using "MHL(Mobile High-Definition Link)"". Move to the upper or lower menu or adjust the value for an option on the OSD menu. 1 Preparations 20 1 Preparations Icons Description When the Key Guide is displayed, the [ ] button activates the function assigned to Volume. Confirm a menu selection. Pressing the [ ] button when the OSD menu is not displayed will change the input source (Analog/HDMI 1/HDMI 2/MHL). If you power on the product or change the input source by pressing the [ ] button, a message that shows the changed input source will appear at the top left corner of the screen. Press the [AUTO] button to automatically adjust the screen settings. AUTO Changing the resolution in Display Properties will activate the Auto Adjustment function. Turn the screen on or off. The power indicator will be lit when the product is operating normally. (Power lamp) To reduce power consumption, it is best to remove the power cable when you will not be using the product for an extended period of time. When a control button on the product is pressed, the Key Guide will be displayed before the onscreen menu opens. (The guide shows the function of the button pressed.) Key Guide To access the onscreen menu when the guide is displayed, press the corresponding button again. The Key Guide may vary depending on the function or product model. Refer to the actual product. 1 Preparations 21 1 Preparations 1.2.2 Reverse Side The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. HDMI 2 / MHL RGB IN DC 14V Port HDMI1 Ports Connect to the DC power adapter. HDMI 1 HDMI 2 / MHL Connect to a source device using an HDMI cable. Connect to a source device that has the MHL function using the MHL cable. Connect to a source device using an HDMI cable. Connect to a PC using the D-SUB cable. Connect to an audio-input source using an audio cable. Connect to an audio output device such as headphones. 1 Preparations 22 1 1.3 Preparations Installation 1.3.1 Attaching the Stand Before assembling the product, place the product down on a flat and stable surface so that the screen is facing downwards. RELEASE LOCK Insert the Stand Connector into the Stand in the direction shown by the figure. Check if the Stand Connector is firmly connected. Turn the connecting screw at the bottom of the stand fully so that it is completely fixed. Place a soft cloth over the table to protect the product and place the product onto the cloth so that the front of the product is facing downwards. Hold the main body of the product with your hand as shown by the figure. - Caution Do not hold the product upside down only by the stand. Push the assembled stand into the main body in the direction of the arrow as shown in the figure. The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. 1 Preparations 23 1 Preparations 1.3.2 Adjusting the Product Tilt The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. -1° (± 2°) ~ 20° (± 2°) You can adjust the tilt of your monitor. Hold the lower part of the product and adjust the tilt carefully. 1 Preparations 24 1 Preparations 1.3.3 Installing a Wall-mount Kit or Desktop Stand Before Installation Power the product off and remove the power cable from the power socket. Place a protective cloth or cushion on a flat surface. Next, place the product with the face down on top of the cloth or cushion. Hold the main body of the product with your hand as shown by the figure. Pull the stand in the direction of the arrow as shown in the figure to separate it. Installing a Wall-mount Kit or Desktop Stand 2 1 A 3 4 B A Attach the wall-mount kit or desktop stand here B Bracket (sold separately) Align the grooves and tightly fasten the screws on the bracket on the product with the corresponding parts on the wall-mount kit or desktop stand you want to attach. 1 Preparations 25 1 Preparations Notes Using a screw longer than the standard length can damage the internal components of the product. The length of screws required for a wall mount that does not comply with the VESA standards may vary depending on the specifications. Do not use screws that do not comply with the VESA standards. Do not attach the wall-mount kit or desktop stand using excessive force. The product may get damaged or fall and cause personal injury. Samsung shall not be held liable for any damage or injury caused by using improper screws or attaching the wall-mount kit or desktop stand using excessive force. Samsung shall not be held liable for any product damage or personal injury caused by using a wallmount kit other than the one specified or from an attempt to install the wall-mount kit on your own. To mount the product on a wall, ensure you purchase a wall-mount kit that can be installed 10cm or farther away from the wall. Be sure to use a wall-mount kit that complies with the standards. 1.3.4 Anti-theft Lock An anti-theft lock allows you to use the product securely even in public places. The locking device shape and locking method depend on the manufacturer. Refer to the user guide provided with your anti-theft locking device for details. The lock device is sold separately. The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. To lock an anti-theft locking device: 1 2 3 4 Fix the cable of your anti-theft locking device to a heavy object such as a desk. Put one end of the cable through the loop on the other end. Insert the locking device into the anti-theft lock slot at the back of the product. Lock the locking device. An anti-theft locking device can be purchased separately. Refer to the user guide provided with your anti-theft locking device for details. Anti-theft locking devices can be purchased at electronics retailers or online. 1 Preparations 26 2 2.1 Using "MHL(Mobile High-Definition Link)" "MHL" (Mobile High-Definition Link) This feature allows you to enjoy videos and photos (imported from a connected mobile device that supports MHL) on the screen of the product. MHL To find a list of MHL-certified devices, go to the Samsung website (http://www.samsung.com). To use the MHL function, the latest version of software must be installed on the mobile device. On some mobile devices, the MHL function may not be available depending on the device's performance or functionality. Since the display size of the product is larger than those of mobile devices, the picture quality may degrade. This product is officially MHL-certified. If you encounter any proble.3m when using the MHL function, please contact the manufacturer of the mobile device. The picture quality may degrade when content (imported from the mobile device) with a low resolution is played on the product. 2 Using "MHL(Mobile High-Definition Link)" 27 2 Using "MHL(Mobile High-Definition Link)" 2.1.1 Using "MHL" 1 Connect the USB port on the mobile device to the [HDMI 2 / MHL] port on the product using the MHL cable. HDMI 2/MHL 2 When the MHL cable is used, [HDMI 2 / MHL] is the only port on the product that supports the MHL function. A mobile device should be purchased separately. Connect the DC power adapter to the product and a power outlet. (For details, refer to "3.2 Connecting the Power".) 3 Press the [MHL] button to activate MHL mode. 4 If the following message appears, MHL mode is activated. And the MHL screen will be displayed. [MHL] 3 sec later MHL activated. DSUB/HDMI1 MHL MHL The indicated time 3 seconds (the waiting time before the MHL screen appears) may vary depending on the mobile device. 2 Using "MHL(Mobile High-Definition Link)" 28 2 Using "MHL(Mobile High-Definition Link)" When the mobile device is in sleep mode When the mobile device is in sleep mode, the following message will appear in place of the MHL screen. To display the MHL screen, deactivate sleep mode. MHL device is in sleep mode. When the mobile device is not connected or does not support MHL When the mobile device is not connected to the product or does not support the MHL function, the following message will appear. If MHL mode is not activated, check the connection of the mobile device. If MHL mode is not activated, check if the mobile device supports MHL. If MHL mode is not activated even though the mobile device supports MHL, update the firmware of the mobile device to the latest version. 3 sec later Check Signal Cable HDMI2/MHL MHL device is not connected or the device doesn't support MHL. MHL MHL The indicated time 3 seconds (the waiting time before the MHL screen appears) may vary depending on the mobile device. 2 Using "MHL(Mobile High-Definition Link)" 29 2 Using "MHL(Mobile High-Definition Link)" 2.1.2 Disabling "MHL" Disabling MHL by using the [MHL] button When MHL is active, press the [MHL] button. The MHL function will be disabled. DSUB (or HDMI1) [MHL] MHL DSUB/HDMI1 The input source changes automatically only when a cable is connected to a port other than [HDMI 2 / MHL]. Check Signal Cable HDMI2/MHL MHL MHL When the cable is disconnected or the mobile device is powered off If the MHL cable is disconnected or the mobile device is powered off when MHL is active, the MHL function will be disabled. 8IFOUIFDBCMFJT EJTDPOOFDUFEPS UIFNPCJMFEFWJDF JTQPXFSFEPGG MHL device disconnected. MHL Check Signal Cable HDMI2/MHL 3 sec later MHL If the MHL cable is disconnected, the product will display the message Check Signal Cable and remain in MHL mode. The indicated time 3 seconds (the waiting time before the MHL screen appears) may vary depending on the mobile device. 2 Using "MHL(Mobile High-Definition Link)" 30 3 3.1 Connecting and Using a Source Device Before Connecting 3.1.1 Pre-connection Checkpoints Before connecting a source device, read the user manual provided with it. The number and locations of ports on source devices may differ from device to device. Do not connect the power cable until all connections are completed. Connecting the power cable during connection may damage the product. 3.2 Check the types of ports at the back of the product you want to connect. Connecting the Power Connect the power adapter to [DC] jack on the rear of the product. Connect the power cord to the adapter and wall socket. (The input voltage is switched automatically.) DC 14V 3 Connecting and Using a Source Device 31 3 3.3 Connecting and Using a Source Device Connecting and Using a PC 3.3.1 Connecting to a PC Select a connection method suitable for your PC. Connecting parts may differ in different products. Connection Using the D-SUB Cable (Analogue Type) RGB IN 1 2 Connect the D-SUB cable to the [RGB IN] port on the back of the product and the RGB port on the PC. Connect the DC power adapter to the product and a power socket. Next, turn on the power switch on the PC. (For details, refer to "3.2 Connecting the Power".) 3 Press [ ] to change the input source to Analog. To enable the sound, connect an audio cable. Connection Using the HDMI Cable HDMI 1 2 Connect the HDMI cable to the HDMI port on the back of the product and the HDMI port on the PC. Connect the DC power adapter to the product and a power socket. Next, turn on the power switch on the PC. (For details, refer to "3.2 Connecting the Power".) 3 Press the [ ] button to change the input source to HDMI 1 or HDMI 2/MHL IN. 3 Connecting and Using a Source Device 32 3 Connecting and Using a Source Device Connection Using an HDMI-DVI Cable HDMI 1 Connect the HDMI-DVI cable to the HDMI port on the back of the product and the DVI port on the PC. 2 Connect the DC power adapter to the product and a power socket. Next, turn on the power switch on the PC. (For details, refer to "3.2 Connecting the Power".) 3 Press the [ ] button to change the input source to HDMI 1 or HDMI 2/MHL IN. To enable the sound, connect an audio cable. 3.3.2 Connecting to Headphones or Speakers AUDIO IN AUDIO OUT 1 Connect an audio output device such as headphones or speakers to [ ] on the product. To enable the sound, connect an audio cable. 3 Connecting and Using a Source Device 33 3 Connecting and Using a Source Device 3.3.3 Driver Installation You can set the optimum resolution and frequency for this product by installing the corresponding drivers. An installation driver is contained on the CD supplied with the product. If the file provided is faulty, visit the Samsung homepage (http://www.samsung.com) and download the file. 1 2 3 4 Insert the user manual CD provided with the product into the CD-ROM drive. 5 Go to Display Properties and check that the resolution and refresh rate are appropriate. Click "Windows Driver". Follow the instructions given on the screen to proceed with installation. Select your product model from the list of models. Refer to your Windows OS manual for further details. 3 Connecting and Using a Source Device 34 3 Connecting and Using a Source Device 3.3.4 Setting Optimum Resolution An information message about setting optimum resolution will appear if you power on the product for the first time after purchase. Select a language and change the resolution to the optimum value. The optimal resolution for this monitor is as follows: **** x **** **Hz Follow the above settings to set the resolution. English EXIT 1 2 Press [ AUTO ] to move to the language you want and press [ ]. To hide the information message, press [ MENU ]. If the optimum resolution is not selected, the message will appear up to three times for a specified time even when the product is turned off and on again. The optimum resolution can also be selected in Control Panel on your PC. 3 Connecting and Using a Source Device 35 3 Connecting and Using a Source Device 3.3.5 Changing the Resolution Using a PC Adjust the resolution and refresh rate in Control Panel on your PC to obtain optimum picture quality. The picture quality of TFT-LCDs may degrade if the optimum resolution is not selected. Changing the Resolution on Windows XP Go to Control Panel 1 Display Settings and change the resolution. 2 3 ********** **** **** 3 Connecting and Using a Source Device 36 3 Connecting and Using a Source Device Changing the Resolution on Windows Vista Go to Control Panel Personalization Display Settings and change the resolution. 1 2 3 4 *********** *********** 3 Connecting and Using a Source Device 37 3 Connecting and Using a Source Device Changing the Resolution on Windows 7 Go to Control Panel Display Screen Resolution and change the resolution. 1 2 3 4 3 Connecting and Using a Source Device 38 4 4.1 Screen Setup Configure the screen settings such as brightness and color tone. Brightness You can adjust the general brightness of the picture. (Range: 0~100) A higher value will make the picture appear brighter. SAMSUNG This menu is not available when MAGIC Bright is set to Dynamic Contrast mode. Not available if Eco Saving is set to On. 4.1.1 Configuring Brightness 1 Press any button on the front of the product to display the Key Guide. Next, press [ MENU ] to display the corresponding menu screen. 2 3 Press [ ] to move to Picture and press [ Press [ ] to move to Brightness and press [ ] on the product. ] on the product. The following screen will appear. PICTURE Brightness Contrast Sharpness SAMSUNG MAGIC Bright Custom SAMSUNG MAGIC Angle Coarse Off Fine AUTO 4 Adjust the Brightness using the [ ] buttons. 4 Screen Setup 39 4 4.2 Screen Setup Contrast Adjust the contrast between the objects and background. (Range: 0~100) A higher value will increase the contrast to make the object appear clearer. SAMSUNG This menu is not available when MAGIC Bright is in Cinema or Dynamic Contrast mode. SAMSUNG This menu is not available when MAGIC Color is in Full or Intelligent mode. 4.2.1 Configuring Contrast 1 Press any button on the front of the product to display the Key Guide. Next, press [ MENU ] to display the corresponding menu screen. 2 3 Press [ ] to move to Picture and press [ Press [ ] to move to Contrast and press [ ] on the product. ] on the product. The following screen will appear. PICTURE Brightness Contrast Sharpness SAMSUNG MAGIC Bright &XVWRP MAGIC Angle Coarse SAMSUNG 2II Fine AUTO 4 Adjust the Contrast using the [ ] buttons. 4 Screen Setup 40 4 4.3 Screen Setup Sharpness Make the outline of objects more clear or blurry. (Range: 0~100) A higher value will make the outline of objects clearer. SAMSUNG This menu is not available when MAGIC Bright is in Cinema or Dynamic Contrast mode. SAMSUNG This menu is not available when MAGIC Color is in Full or Intelligent mode. 4.3.1 Configuring Sharpness 1 Press any button on the front of the product to display the Key Guide. Next, press [ MENU ] to display the corresponding menu screen. 2 3 Press [ ] to move to Picture and press [ Press [ ] to move to Sharpness and press [ ] on the product. ] on the product. The following screen will appear. PICTURE Brightness Contrast Sharpness SAMSUNG MAGIC Bright Custom MAGIC Angle Coarse SAMSUNG Off Fine AUTO 4 Adjust the Sharpness using the [ ] buttons. 4 Screen Setup 41 4 4.4 Screen Setup SAMSUNG MAGIC Bright This menu provides an optimum picture quality suitable for the environment where the product will be used. Not available if Eco Saving is set to On. SAMSUNG This menu is not available when MAGIC Angle is enabled. You can customize the brightness to suit your preferences. 4.4.1 Configuring SAMSUNG MAGIC Bright 1 Press any button on the front of the product to display the Key Guide. Next, press [ MENU ] to display the corresponding menu screen. 2 3 Press [ ] to move to Picture and press [ ] on the product. Press [ SAMSUNG ] to move to MAGIC Bright and press [ ] on the product. The following screen will appear. PICTURE Brightness Contrast Sharpness SAMSUNG MAGIC Bright Custom ࢽ࣏ࡈی SAMSUNG MAGIC Angle Coarse ଥࢿ Game Fine Standard Cinema Dynamic Contrast AUTO Custom: Customize the contrast and brightness as required. Standard: Obtain a picture quality suitable for editing documents or using Internet. Game: Obtain a picture quality suitable for playing games that involve many graphic effects and dynamic movements. Cinema: Obtain the brightness and sharpness of TVs suitable for enjoying video and DVD content. 4 Screen Setup 42 4 Screen Setup Dynamic Contrast: Obtain balanced brightness through automatic contrast adjustment. PICTURE Brightness Contrast Sharpness SAMSUNG MAGIC Bright Dynamic ࢽ࣏ࡈی SAMSUNG MAGIC Angle Coarse ଥࢿ Movie Fine Standard Custom AUTO SAMSUNG When the external input is connected through HDMI and PC/AV Mode is set to AV, MAGIC Bright has four automatic picture settings (Dynamic, Standard, Movie and Custom) that are preset at the factory. You can activate either Dynamic, Standard, Movie or Custom. You can select Custom which automatically recalls your personalized picture settings. Dynamic: Select this mode to view a sharper image than in Standard mode. Standard: Select this mode when the surroundings are bright. This also provides a sharp image. Movie: Select this mode when the surroundings are dark. This will save power and reduce eye fatigue. 4 5 Custom: Select this mode when you want to adjust the image according to your preferences. Press [ ] to move to the option you want and press [ ]. The selected option will be applied. 4 Screen Setup 43 4 4.5 Screen Setup SAMSUNG MAGIC Angle SAMSUNG MAGICAngle allows you to configure the settings to obtain the optimum picture quality according to your viewing angle. SAMSUNG This menu is not available when MAGIC Bright is in Cinema or Dynamic Contrast mode. SAMSUNG This menu is not available when MAGIC Color is enabled. You can customize the angle to suit your preferences. 4.5.1 Configuring SAMSUNG MAGIC Angle 1 Press any button on the front of the product to display the Key Guide. Next, press [ MENU ] to display the corresponding menu screen. 2 3 Press [ ] to move to Picture and press [ ] on the product. Press [ SAMSUNG ] to move to MAGIC Angle and press [ ] on the product. The following screen will appear. PICTURE Brightness Contrast Sharpness SAMSUNG MAGIC Bright Off ࢽ࣏ࡈی SAMSUNG MAGIC Angle Coarse Lean Back Mode 2 Fine Group View Lean Back Mode 1 Standing Mode ଥࢿ Side Mode Custom AUTO 4 1 1 5 5 2 3 4 5 ① : Select this option to view directly in front of the product. Lean Back Mode 1 ② : Select this option to view from a place slightly lower than the product. Lean Back Mode 2 ③ : Select this option to view from a place lower than Lean Back Mode 1. Standing Mode ④ : Select this option to view from a place higher than the product. Side Mode ⑤ : Select this option to view from either side of the product. Group View: Select this option for more than one viewer to view from places ① , ④ , and ⑤ . Off Custom: Lean Back Mode 1 will be applied by default if Custom is selected. Press [ ] to move to the option you want and press [ ]. The selected option will be applied. 4 Screen Setup 44 4 4.6 Screen Setup Coarse Adjust the screen frequency. This menu is available in Analog mode only. 4.6.1 Adjusting Coarse 1 Press any button on the front of the product to display the Key Guide. Next, press [ MENU ] to display the corresponding menu screen. 2 3 Press [ ] to move to Picture and press [ ] on the product. Press [ ] to move to Coarse and press [ ] on the product. The following screen will appear. PICTURE Brightness Contrast Sharpness SAMSUNG MAGIC Bright Custom SAMSUNG MAGIC Angle Coarse Off Fine AUTO 4 Adjust the Coarse using the [ ] buttons. 4 Screen Setup 45 4 4.7 Screen Setup Fine Fine-adjust the screen to obtain a vivid picture. This menu is available in Analog mode only. 4.7.1 Adjusting Fine 1 Press any button on the front of the product to display the Key Guide. Next, press [ MENU ] to display the corresponding menu screen. 2 3 Press [ ] to move to Picture and press [ Press [ ] to move to Fine and press [ ] on the product. ] on the product. The following screen will appear. PICTURE Brightness Contrast Sharpness SAMSUNG MAGIC Bright Custom SAMSUNG MAGIC Angle Coarse Off Fine AUTO 4 Adjust the Fine using the [ ] buttons. 4 Screen Setup 46 4 4.8 Screen Setup Response Time Accelerate the panel response rate to make video appear more vivid and natural. It is best to set Response Time to Normal or Faster when you are not viewing a movie. The functions available on the monitor may vary depending on the model. Refer to the actual product. 4.8.1 Configuring Response Time 1 Press any button on the front of the product to display the Key Guide. Next, press [ MENU ] to display the corresponding menu screen. 2 3 Press [ ] to move to Picture and press [ ] on the product. Press [ ] to move to Response Time and press [ ] on the product. The following screen will appear. PICTURE Response Time Normal HDMI Black Level Fastest Faster AUTO 4 5 Press [ ] to move to the option you want and press [ ]. The selected option will be applied. 4 Screen Setup 47 4 4.9 Screen Setup HDMI Black Level If a DVD player or set-top box is connected to the product via HDMI, image quality degradation (contrast/ color degradation, black level, etc.) may occur, depending on the connected source device. In such case, HDMI Black Level can be used to adjust the image quality. If this is the case, correct the degraded picture quality using HDMI Black Level. 4.9.1 Configuring the HDMI Black Level Settings 1 Press any button on the front of the product to display the Key Guide. Next, press [ MENU ] to display the corresponding menu screen. 2 3 Press [ ] to move to Picture and press [ ] on the product. Press [ ] to move to HDMI Black Level and press [ ] on the product. The following screen will appear. PICTURE Response Time : Faster HDMI Black Level Normal Low AUTO Normal: Select this mode when there is no contrast ratio degradation. Low: Select this mode to reduce the black level and increase the white level when there is a contrast ratio degradation. 4 5 Press [ ] to move to the option you want and press [ ]. The selected option will be applied. HDMI Black Level may not be compatible with some source devices. 4 Screen Setup 48 5 Configuring Tint SAMSUNG Adjust the tint of the screen. This menu is not available when MAGIC Bright is set to Cinema or Dynamic Contrast mode. 5.1 SAMSUNG MAGIC Color SAMSUNG MAGICColor is a new picture-quality improvement technology developed independently by Samsung, which delivers vivid natural colors without picture quality degradation. SAMSUNG This menu is not available when MAGIC Angle is enabled. 5.1.1 Configuring SAMSUNG MAGIC Color 1 Press any button on the front of the product to display the Key Guide. Next, press [ MENU ] to display the corresponding menu screen. 2 3 Press [ ] to move to COLOR and press [ ] on the product. Press [ SAMSUNG ] to move to MAGIC Color and press [ ] on the product. The following screen will appear. COLOR SAMSUNG MAGIC Color : Red : Green : Blue : Color Tone : Normal Gamma : Mode 1 Off Demo Full Intelligent AUTO 4 5 SAMSUNG Off: Disable MAGIC Color. SAMSUNG Demo: Compare normal screen mode with MAGIC Color mode. Full: Obtain a vivid picture quality for all areas including the flesh colors in the picture. Intelligent: Improve the chroma for all areas except the flesh colors in the picture. Press [ ] to move to the option you want and press [ ]. The selected option will be applied. 5 Configuring Tint 49 5 5.2 Configuring Tint Red Adjust the value of the color red in the picture. (Range: 0~100) A higher value will increase the intensity of the color. SAMSUNG This menu is not available when MAGIC Color is in Full or Intelligent mode. 5.2.1 Configuring Red 1 Press any button on the front of the product to display the Key Guide. Next, press [ MENU ] to display the corresponding menu screen. 2 3 Press [ ] to move to COLOR and press [ Press [ ] to move to Red and press [ ] on the product. ] on the product. The following screen will appear. COLOR SAMSUNG MAGIC Color : Off Red : Green : Blue : Color Tone : Normal Gamma : Mode 1 AUTO 4 Adjust the Red using the [ ] buttons. 5 Configuring Tint 50 5 5.3 Configuring Tint Green Adjust the value of the color green in the picture. (Range: 0~100) A higher value will increase the intensity of the color. SAMSUNG This menu is not available when MAGIC Color is in Full or Intelligent mode. 5.3.1 Configuring Green 1 Press any button on the front of the product to display the Key Guide. Next, press [ MENU ] to display the corresponding menu screen. 2 3 Press [ ] to move to COLOR and press [ Press [ ] to move to Green and press [ ] on the product. ] on the product. The following screen will appear. COLOR SAMSUNG MAGIC Color : Red : Green : Blue : Color Tone : Normal Gamma : Mode 1 Off AUTO 4 Adjust the Green using the [ ] buttons. 5 Configuring Tint 51 5 5.4 Configuring Tint Blue Adjust the value of the color blue in the picture. (Range: 0~100) A higher value will increase the intensity of the color. SAMSUNG This menu is not available when MAGIC Color is in Full or Intelligent mode. 5.4.1 Configuring Blue 1 Press any button on the front of the product to display the Key Guide. Next, press [ MENU ] to display the corresponding menu screen. 2 3 Press [ ] to move to COLOR and press [ Press [ ] to move to Blue and press [ ] on the product. ] on the product. The following screen will appear. COLOR SAMSUNG MAGIC Color : Red : Green : Blue : Color Tone : Normal Gamma : Mode 1 Off AUTO 4 Adjust the Blue using the [ ] buttons. 5 Configuring Tint 52 5 5.5 Configuring Tint Color Tone Adjust the general color tone of the picture. SAMSUNG This menu is not available when MAGIC Color is in Full or Intelligent mode. SAMSUNG This menu is not available when MAGIC Angle is enabled. 5.5.1 Configuring the Color Tone Settings 1 Press any button on the front of the product to display the Key Guide. Next, press [ MENU ] to display the corresponding menu screen. 2 3 Press [ ] to move to COLOR and press [ ] on the product. Press [ ] to move to Color Tone and press [ ] on the product. The following screen will appear. COLOR SAMSUNG MAGIC Color Red Green Blue Color Tone Gamma : Off : : : &RRO &RRO : ࣱ 1RUPDO :DUP : ֻҖ :DUP &XVWRP AUTO Cool 2: Set the color temperature to be cooler than Cool 1. Cool 1: Set the color temperature to be cooler than Normal mode. Normal: Display the standard color tone. Warm 1: Set the color temperature to be warmer than Normal mode. Warm 2: Set the color temperature to be warmer than Warm 1. Custom: Customize the color tone. When the external input is connected through HDMI and PC/AV Mode is set to AV,Color Tone has four color temperature settings (Cool, Normal, Warm and Custom). 4 5 Press [ ] to move to the option you want and press [ ]. The selected option will be applied. 5 Configuring Tint 53 5 5.6 Configuring Tint Gamma Adjust the mid-range brightness (Gamma) of the picture. SAMSUNG This menu is not available when MAGIC Angle is enabled. 5.6.1 Configuring Gamma 1 Press any button on the front of the product to display the Key Guide. Next, press [ MENU ] to display the corresponding menu screen. 2 3 Press [ ] to move to COLOR and press [ ] on the product. Press [ ] to move to Gamma and press [ ] on the product. The following screen will appear. COLOR SAMSUNG MAGIC Color Red Green Blue Color Tone Gamma : Off : : : : Normal : Mode ֻҖ1 Mode 2 Mode 3 AUTO 4 5 Press [ ] to move to the option you want and press [ ]. The selected option will be applied. 5 Configuring Tint 54 6 6.1 Resizing or Relocating the Screen H-Position & V-Position H-Position: Move the screen to the left or right. V-Position: Move the screen up or down. Available only when Image Size is set to Screen Fit. This menu is available in Analog mode only. 6.1.1 Configuring H-Position & V-Position 1 Press any button on the front of the product to display the Key Guide. Next, press [ MENU ] to display the corresponding menu screen. 2 3 Press [ ] to move to SIZE&POSITION and press [ ] on the product. Press [ ] to move to H-Position or V-Position, and press [ ]. The following screen will appear. SIZE&POSITION SIZE&POSITION H-Position H-Position V-Position V-Position Image Size Auto Image Size Auto Menu H-Position Menu H-Position Menu V-Position Menu V-Position AUTO 4 Press [ AUTO ] to configure H-Position or V-Position. 6 Resizing or Relocating the Screen 55 6 6.2 Resizing or Relocating the Screen Image Size Change the picture size. 6.2.1 Changing the Image Size 1 Press any button on the front of the product to display the Key Guide. Next, press [ MENU ] to display the corresponding menu screen. 2 3 Press [ ] to move to SIZE&POSITION and press [ Press [ ] to move to Image Size and press [ ] on the product. ] on the product. The following screen will appear. SIZE&POSITION H-Position V-Position Image Size Menu H-Position Ѱ $XWR :LGH Menu V-Position AUTO Auto: Display the picture according to the aspect ratio of the input source. Wide: Display the picture in full screen regardless of the aspect ratio of the input source. SIZE&POSITION H-Position V-Position Image Size Ѱ 6FUHHQ)LW Menu H-Position Menu V-Position AUTO 4:3: Display the picture with an aspect ratio of 4:3. Suitable for videos and standard broadcasts. 16:9: Sets the picture to 16:9 wide mode. Screen Fit: Display the picture with the original aspect ratio without cutting off. Changing the screen size is available when the following conditions are satisfied. 4 5 A digital output device is connected using the DVI cable. The input signal is 480p, 576p, 720p, or 1080p. Press [ ] to move to the option you want and press [ ]. The selected option will be applied. 6 Resizing or Relocating the Screen 56 6 6.3 Resizing or Relocating the Screen Menu H-Position & Menu V-Position Menu H-Position: Move the menu position to the left or right. Menu V-Position: Move the menu position up or down. 6.3.1 Configuring Menu H-Position & Menu V-Position 1 Press any button on the front of the product to display the Key Guide. Next, press [ MENU ] to display the corresponding menu screen. 2 3 Press [ ] to move to SIZE&POSITION and press [ ] on the product. Press [ ] to move to Menu H-Position or Menu V-Position, and press [ ]. The following screen will appear. SIZE&POSITION SIZE&POSITION H-Position H-Position V-Position V-Position Image Size $XWR Image Size $XWR Menu H-Position Menu H-Position Menu V-Position Menu V-Position AUTO 4 Press [ AUTO ] to configure Menu H-Position or Menu V-Position. 6 Resizing or Relocating the Screen 57 7 7.1 Setup and Reset Reset Return all the settings for the product to the default factory settings. 7.1.1 Initializing Settings (Reset) 1 Press any button on the front of the product to display the Key Guide. Next, press [ MENU ] to display the corresponding menu screen. 2 3 Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to Reset and press [ ] on the product. ] on the product. The following screen will appear. SETUP&RESET Reset Language (QJOLVK Eco Saving Off Off Timer On/Off Off Off Timer Setting PC/AV Mode Key Repeat Time Acceleration AUTO Reset all settings? Yes EXIT 4 5 Press [ No AUTO ] to move to the option you want and press [ ]. The selected option will be applied. 7 Setup and Reset 58 7 7.2 Setup and Reset Language Set the menu language. A change to the language setting will only be applied to the onscreen menu display. It will not be applied to other functions on your PC. 7.2.1 Changing the Language 1 Press any button on the front of the product to display the Key Guide. Next, press [ MENU ] to display the corresponding menu screen. 2 3 Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to Language and press [ ] on the product. ] on the product. The following screen will appear. SETUP&RESET 5HVHW /DQJXDJH (FR6DYLQJ 2II7LPHU2Q2II 2II7LPHU6HWWLQJ 3&$90RGH .H\5HSHDW7LPH 'HXWVFK (QJOLVK (VSDxRO )UDQoDLV ,WDOLDQR ଥࢿ 0DJ\DU 3ROVNL ଥࢿ 3RUWXJXrV ƧNJLjLjǁƿǀ 6YHQVND 7UNoH 3& ᣣᧄ⺆ ଞ˲߭ ɼܖ؆ـ ∝䇁 AUTO 4 5 Press [ ] to move to the language you want and press [ ]. The selected option will be applied. 7 Setup and Reset 59 7 7.3 Setup and Reset Eco Saving The Eco Saving function reduces power consumption by controlling the electric current used by the monitor panel. SAMSUNG This menu is not available when MAGIC Bright is in Dynamic Contrast mode. 7.3.1 Configuring Eco Saving 1 Press any button on the front of the product to display the Key Guide. Next, press [ MENU ] to display the corresponding menu screen. 2 3 Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to Eco Saving and press [ ] on the product. ] on the product. The following screen will appear. SETUP&RESET 5HVHW /DQJXDJH English (FR6DYLQJ ଥࢿ 2II7LPHU2Q2II ଥࢿ Off 2II7LPHU6HWWLQJ 3&$90RGH .H\5HSHDW7LPH Acceleration AUTO 4 5 75% : Change the monitor power consumption to 75% of the default level. 50% : Change the monitor power consumption to 50% of the default level. Off: Deactivate the Eco Saving function. Press [ ] to move to the option you want and press [ ]. The selected option will be applied. 7 Setup and Reset 60 7 7.4 Setup and Reset Off Timer On/Off You can set the product to automatically turn off. 7.4.1 Configuring Off Timer On/Off 1 Press any button on the front of the product to display the Key Guide. Next, press [ MENU ] to display the corresponding menu screen. 2 3 Press [ ] to move to SETUP&RESET and press [ ] on the product. Press [ ] to move to Off Timer On/Off and press [ ] on the product. The following screen will appear. SETUP&RESET 5HVHW /DQJXDJH (QJOLVK (FR6DYLQJ : Off 2II7LPHU2Q2II Off On 2II7LPHU6HWWLQJ 3&$90RGH .H\5HSHDW7LPH Acceleration AUTO 4 5 Off: Deactivate the off timer so that the product does not power off automatically. On: Activate the off timer so that the product powers off automatically. Press [ ] to move to the option you want and press [ ]. The selected option will be applied. 7 Setup and Reset 61 7 7.5 Setup and Reset Off Timer Setting The off timer can be set within a range of 1 to 23 hours. The product will automatically power off after the specified number of hours. This menu is available only when Off Timer On/Off is set to On. 7.5.1 Configuring Off Timer Setting 1 Press any button on the front of the product to display the Key Guide. Next, press [ MENU ] to display the corresponding menu screen. 2 3 Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to Off Timer Setting and press [ ] on the product. ] on the product. The following screen will appear. SETUP&RESET 5HVHW /DQJXDJH English (FR6DYLQJ Off 2II7LPHU2Q2II On 2II7LPHU6HWWLQJ 10h 3&$90RGH .H\5HSHDW7LPH Acceleration AUTO 4 Press [ ] to configure Off Timer Setting. 7 Setup and Reset 62 7 7.6 Setup and Reset PC/AV Mode Set PC/AV Mode to AV. The picture size will be enlarged. This option is useful when you view a movie. PC/AV Mode is available in HDMI mode only. 7.6.1 Configuring PC/AV Mode 1 Press any button on the front of the product to display the Key Guide. Next, press [ MENU ] to display the corresponding menu screen. 2 3 Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to PC/AV Mode and press [ ] on the product. ] on the product. The following screen will appear. SETUP&RESET Reset Language (QJOLVK Eco Saving Off Off Timer On/Off On Off Timer Setting 10h PC/AV Mode Key Repeat Time $FFHOHUDWLRQ AUTO PC/AV Mode +'0, +'0, 3& $9 ೳ AUTO 4 5 Press [ ] to move to the option you want and press [ ]. The selected option will be applied. 7 Setup and Reset 63 7 7.7 Setup and Reset Key Repeat Time Control the response rate of a button when the button is pressed. 7.7.1 Configuring Key Repeat Time 1 Press any button on the front of the product to display the Key Guide. Next, press [ MENU ] to display the corresponding menu screen. 2 3 Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to Key Repeat Time and press [ ] on the product. ] on the product. The following screen will appear. SETUP&RESET 5HVHW /DQJXDJH English (FR6DYLQJ Off 2II7LPHU2Q2II On 2II7LPHU6HWWLQJ 3&$90RGH .H\5HSHDW7LPH Acceleration 1 sec 2 sec No Repeat ݤɾ AUTO Acceleration, 1 sec, or 2 sec can be selected. If No Repeat is selected, a command responds only once when a button is pressed. 4 5 Press [ ] to move to the option you want and press [ ]. The selected option will be applied. 7 Setup and Reset 64 7 7.8 Setup and Reset Auto Source You can activate Auto Source. 7.8.1 Configuring Auto Source 1 Press any button on the front of the product to display the Key Guide. Next, press [ MENU ] to display the corresponding menu screen. 2 3 Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to Auto Source and press [ ] on the product. ] on the product. The following screen will appear. SETUP&RESET 'LVSOD\7LPH Auto Manual 0HQX7UDQVSDUHQF\ On $XWR6RXUFH AUTO 4 5 Auto: The input source is automatically recognized. Manual: Manually select an input source. Press [ ] to move to the option you want and press [ ]. The selected option will be applied. 7 Setup and Reset 65 7 7.9 Setup and Reset Display Time Set the on-screen display (OSD) menu to automatically disappear if the menu is not used for a specified period of time. Display Time can be used to specify the time after which you want the OSD menu to disappear. 7.9.1 Configuring Display Time 1 Press any button on the front of the product to display the Key Guide. Next, press [ MENU ] to display the corresponding menu screen. 2 3 Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to Display Time and press [ ] on the product. ] on the product. The following screen will appear. SETUP&RESET $XWR6RXUFH 0DQXDO 'LVSOD\7LPH VHF VHF VHF VHF 0HQX7UDQVSDUHQF\ AUTO 4 5 Press [ ] to move to the option you want and press [ ]. The selected option will be applied. 7 Setup and Reset 66 7 Setup and Reset 7.10 Menu Transparency Set the transparency for the menu windows: 7.10.1 Changing Menu Transparency 1 Press any button on the front of the product to display the Key Guide. Next, press [ MENU ] to display the corresponding menu screen. 2 3 Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to Menu Transparency and press [ ] on the product. ] on the product. The following screen will appear. SETUP&RESET $XWR6RXUFH : Manual 'LVSOD\7LPH : 20 sec 0HQX7UDQVSDUHQF\ : Off On AUTO 4 5 Press [ ] to move to the option you want and press [ ]. The selected option will be applied. 7 Setup and Reset 67 8 8.1 INFORMATION Menu and Others INFORMATION View the current input source, frequency and resolution. 8.1.1 Displaying INFORMATION 1 Press any button on the front of the product to display the Key Guide. Next, press [ MENU ] to display the corresponding menu screen. 2 Press [ ] to move to INFORMATION. The current input source, frequency and resolution will appear. PICTURE COLOR Analog **kHz **Hz NP **** x **** SIZE&POSITION Optimal Mode **** x **** **Hz SETUP&RESET INFORMATION AUTO EXIT The displayed menu items may vary depending on the model. 8.2 Configuring Volume in the Initial Screen 8.2.1 Volume Adjust the Volume by pressing the [ 1 Press any button on the front of the product (when no menu screen is displayed) to display the Key Guide. Next, press [ 2 ] button when the Key Guide is displayed. Press [ ]. ] to move to Volume and press [ ] on the product. The following screen will appear. Volume Volume 6RXQG0RGH Standard ೳ AUTO 3 Adjust the Volume using the [ ] buttons. 8 INFORMATION Menu and Others 68 8 INFORMATION Menu and Others 8.2.2 Sound Mode Select a sound mode (Mode) suitable for the environment where the product will be used. This item is not available when connecting to headphones. 1 Press any button on the front of the product (when no menu screen is displayed) to display the Key Guide. Next, press [ 2 Press [ ]. ] to move to Sound Mode and press [ ] on the product. The following screen will appear. Volume 9ROXPH 6RXQG0RGH Standard Music Movie Clear Voice ೳ AUTO 3 4 Standard: Provides sound suitable for any type of content. Music: Provides sound close to the original experience. Movie: Provides a grand sound experience. Clear Voice: Hear voices clearly. Press [ ] to move to the option you want and press [ ]. The selected option will be applied. 8 INFORMATION Menu and Others 69 9 9.1 Installing the Software Magic Tune 9.1.1 What is MagicTune? MagicTune is a software program that helps with monitor adjustments by providing comprehensive descriptions of monitor functions and easy-to-understand guidelines. You can adjust the product with the mouse and the keyboard without using the operating buttons of the product. 9.1.2 Installing the Software 1 2 Insert the installation CD into the CD-ROM drive. Select the MagicTune setup program. If the pop-up screen for the software installation does not appear on the main screen, find and double-click the MagicTune setup file on the CD-ROM. 3 4 Select the installation language and click [Next]. Complete the remaining software installation steps according to the instructions displayed on the screen. The software may not work properly if you do not restart the computer after the installation. The MagicTune icon may not appear depending on the computer system and the product specifications. If the shortcut icon does not appear, press the F5 key. Restrictions and Problems with the Installation (MagicTune™) The installation of MagicTune™may be affected by the graphics card, motherboard and the networking environment. System Requirements OS Windows XP, Windows Vista, Windows 7 9 Installing the Software 70 9 Installing the Software 9.1.3 Removing the Software You can only remove MagicTune™ through [Add or Remove Programs] in Windows. To remove MagicTune™, complete the following steps. 1 Click [Start] select [Settings], and select [Control Panel] from the menu. For Windows XP, click [Start], and select [Control Panel] from the menu. 2 3 4 5 6 Double-click the [Add or Remove Programs] icon in the Control Panel. In the [Add/Remove] window, find and select MagicTune™so that it is highlighted. Click [Change or Remove Programs] to remove the software. Select [Yes] to start removing MagicTune™. Wait until a message box appears informing you that the software has been removed completely. For technical support, the FAQ (frequently asked questions) or information about the software upgrade for MagicTune™, please visit our website(http://www.samsung.com/us/consumer/ learningresources/monitor/magetune/pop_intro.html). 9 Installing the Software 71 9 9.2 Installing the Software MultiScreen MultiScreen MultiScreen enables users to use the monitor by partitioning multiple sections. 9.2.1 Installing the Software 1 2 Insert the installation CD into the [CD-ROM drive]. Select the "MultiScreen" setup program. If the pop-up screen for the software installation does not appear on the main screen, find and double-click the "MultiScreen" setup file on the [CD-ROM]. 3 4 When the Installation Wizard appears, click [Next]. Follow the instructions given on the screen to proceed with installation. The software may not work properly if you do not restart the computer after the installation. The "MultiScreen" icon may not appear depending on the computer system and the product specifications. If the shortcut icon does not appear, press the "F5" key. Restrictions and Problems with the Installation (MultiScreen) The "MultiScreen" installation may be affected by the [Graphics card], [Motherboard] and the [Networking environment]. Operating System "OS" "Windows 2000" "Windows XP Home Edition" "Windows XP Professional" "Windows Vista 32bit" "Windows 7 32bit" For "MultiScreen", the operating systems "Windows 2000" or later is recommended. "Hardware" At least 32MB of memory At least 60MB of free space on the hard disk drive 9 Installing the Software 7 2 9 Installing the Software 9.2.2 Removing the Software Click [Start], select [Settings]/[Control Panel], and then double-click [Add or Remove Programs]. Select "MultiScreen" from the program list and click the [Add/Delete] button. 9 Installing the Software 73 10 Troubleshooting Guide 10.1 Requirements Before Contacting Samsung Customer Service Center 10.1.1 Testing the Product Before calling Samsung Customer Service Center, test your product as follows. If the problem persists, contact Samsung Customer Service Center. Check if your product is operating normally by using the product test function. If the screen is turned off and the power indicator blinks even though the product is properly connected to a PC, perform a self-diagnosis test. 1 2 3 4 Power off both the PC and product. Disconnect the cables from the product. Power on the product. If the message "Check Signal Cable" appears, the product is working normally. If the screen remains blank, check the PC system, video controller and cable. 10.1.2 Checking the Resolution and Frequency For a mode that exceeds the supported resolution (refer to "11.3 Standard Signal Mode Table"), the message "Not Optimum Mode" will appear for a short time. 10.1.3 Check the following. Installation issue (PC mode) The screen keeps switching on and off. Check the cable connection between the product and PC, and ensure the connectors are locked. (Refer to "3.3 Connecting and Using a PC") Screen issue The power LED is off. The screen will not switch on. Check that the power cable is connected properly. (Refer to "3.3 Connecting and Using a PC") The message "Check Signal Cable" appears. Check that the cable is properly connected to the product. (Refer to "3.3 Connecting and Using a PC") Check that the device connected to the product is powered on. 10 Troubleshooting Guide 74 10 Troubleshooting Guide Screen issue "Not Optimum Mode" is displayed. This message appears if the signal from the graphics card exceeds the maximum resolution or frequency for the product. Change the maximum resolution and frequency to suit the product performance, referring to Standard Signal Mode Table (page 82). The images on the screen look distorted. Check the cable connection to the product (Refer to "3.3 Connecting and Using a PC") The screen is not clear. The screen is blurry. Adjust Coarse (page 45) and Fine (page 46). Remove any accessories (video extension cable, etc.) and try again. Set the resolution and frequency to the recommended level. (Refer to "11.1 General") The screen appears unstable and shaky. There are shadows or ghost images left on the screen. Check that the resolution and frequency for the PC are within the range of resolution and frequency compatible with the product. Next, if required, change the settings, referring to Standard Signal Mode Table (page 82) in this manual and the INFORMATION menu on the product. The screen is too bright. The screen is too dark. Adjust Brightness (page 39) and Contrast (page 40). Screen color is inconsistent. Change the COLOR settings. (Refer to " Configuring Tint") The colors on the screen have a shadow and are distorted. Change the COLOR settings. (Refer to " Configuring Tint") White does not really look white. Change the COLOR settings. (Refer to " Configuring Tint") There is no image on the screen and the power LED blinks every 0.5 to 1 second. The product is operating in power-saving mode. Press any key on the keyboard or move the mouse to return to normal operating mode. Sound issue There is no sound. Check the connection of the audio cable or adjust the volume. Check the volume. 10 Troubleshooting Guide 75 10 Troubleshooting Guide Sound issue The volume is too low. Adjust the volume. If the volume is still low after turning it up to the maximum level, adjust the volume on your PC sound card or software program. Source device issue A beeping sound is heard when my PC is booting. If a beeping sound is heard when your PC is booting, have your PC serviced. 10 Troubleshooting Guide 76 10 Troubleshooting Guide 10.2 Q & A Question How can I change the frequency? Answer Set the frequency on your graphics card. Windows XP: Go to Control Panel Themes Display Settings Appearance and Advanced Monitor, and adjust Refresh rate under Monitor settings. Windows ME/2000: Go to Control Panel Settings Advanced Display Monitor, and adjust Refresh rate under Monitor settings. Windows Vista: Go to Control Panel Appearance and Personalization Display Settings Advanced Settings Personalization Monitor, and adjust Refresh rate under Monitor settings. Windows 7: Go to Control Panel Personalization Advanced settings Display Appearance and Screen Resolution Monitor, and adjust Refresh rate under Monitor settings. 10 Troubleshooting Guide 77 10 Troubleshooting Guide Question How can I change the resolution? Answer Windows XP: Go to Control Panel Themes Display Appearance and Settings, and adjust the resolution. Windows ME/2000: Go to Control Panel Display Settings, and adjust the resolution. Windows Vista: Go to Control Panel Personalization Personalize Appearance and Display Settings, and adjust the resolution. Windows 7: Go to Control Panel Personalization Display Appearance and Adjust Resolution, and adjust the resolution. How do I set power-saving mode? Windows XP: Set power-saving mode in Control Panel Appearance and Themes Display Screen Saver Settings or BIOS SETUP on the PC. Windows ME/2000: Set power-saving mode in Control Panel Display Screen Saver Settings or BIOS SETUP on the PC. Windows Vista: Set power-saving mode in Control Panel Appearance and Personalization Personalize Screen Saver Settings or BIOS SETUP on the PC. Windows 7: Set power-saving mode in Control Panel Appearance and Personalization Personalize Screen Saver Settings or BIOS SETUP on the PC. Refer to the user manual for your PC or graphics card for further instructions on adjustment. 10 Troubleshooting Guide 78 11 Specifications 11.1 General Model Name S23B550V S27B550V Size 23 Inches (58 cm) 27 Inches (68 cm) Display area 509.76 mm (H) x 286.74 mm (V) 597.89 mm (H) x 336.31 mm (V) Horizontal Frequency 30 ~ 81 kHz Vertical Frequency 56 ~ 75 kHz Panel Synchronization Display Color 16.7M Optimum Resolution 1920x1080@60Hz Maximum Resolution 1920x1080@60Hz Resolution Maximum Pixel Clock 164MHz (Analog,HDMI) This product uses 100 to 240V. Power Supply Refer to the label at the back of the product as the standard voltage can vary in different countries. 15pin-to-15pin D-sub cable, Detachable HDMI to DVI Cable, Detachable HDMI to MHL Cable, Detachable Signal connectors HDMI Cable, Detachable Stereo cable,Detachable Without Stand Dimensions (W x H x D) / Weight With Stand VESA Mounting Interface 553.2 x 336.2 x 56.3 mm 649.6 x 393.6 x 58 mm 21.8 x 13.2 x 2.2 Inches 25.6 x 15.5 x 2.3 Inches 553.2 x 410.15 x 195.0 mm / 3.05 kg 649.6 x 466.9 x 252 mm / 4.60 kg 21.8 x 16.1 x 7.7 Inches / 6.7 lbs 25.6 x 18.4 x 9.9 Inches / 10.1 lbs 75 mm x 75 mm 100 mm x 100 mm 3.0 Inches x 3.0 Inches 3.9 Inches x 3.9 Inches (For use with Specialty(Arm) Mounting hardware.) (For use with Specialty(Arm) Mounting hardware.) 11 Specifications 79 11 Specifications Model Name S23B550V Operating Temperature : 50°F – 104°F (10°C – 40°C) Humidity : 10 % – 80 %, non-condensing Storage Temperature : -4°F – 113°F (-20°C – 45°C) Humidity : 5 % – 95 %, non-condensing Environmental considerations S27B550V Plug-and-Play This monitor can be installed and used with any Plug-and-Play compatible systems. Two-way data exchange between the monitor and PC system optimizes the monitor settings. Monitor installation takes place automatically. However, you can customize the installation settings if desired. Panel Dots (Pixels) Due to the nature of the manufacturing of this product, approximately 1 pixel per million (1ppm) may be brighter or darker on the LCD panel. This does not affect product performance. The above specifications are subject to change without notice to improve quality. This device is a Class B digital apparatus. (broadcast communications device for home use) This Class B device designed for home use is registered for EMC requirements and can be used in all regions. (USA only) Dispose unwanted electronics through an approved recycler. To find the nearest recycling location, go to our website: www.samsung.com/recyclingdirect or call, (877) 278 - 0799 11 Specifications 80 11 Specifications 11.2 PowerSaver The power-saving function of this product reduces power consumption by switching off the screen and changing the color of the power LED if the product is not used for a specified period of time. The power is not turned off in power-saving mode. To switch the screen back on, press any key on the keyboard or move the mouse. Power-saving mode functions only when the product is connected to a PC that has a power-saving function. S23B550V PowerSaver Normal operation mode Power saving mode Power off (Power button) Power Indicator On Blinking Off less than 0.5 watts less than 0.5 watts In this case, the [ HDMI2/MHL] interface is not connected to the mobile device. In this case, the [ HDMI2/MHL] interface is not connected to the mobile device. Power Consumption 30 watts S27B550V PowerSaver Normal operation mode Power saving mode Power off (Power button) Power Indicator On Blinking Off less than 0.5 watts less than 0.5 watts In this case, the [ HDMI2/MHL] interface is not connected to the mobile device. In this case, the [ HDMI2/MHL] interface is not connected to the mobile device. Power Consumption 40 watts The power consumption level can vary in different operating conditions or when settings are changed. To reduce the power consumption to 0 watts, turn off the power switch on the back of the product or disconnect the power cable. Be sure to disconnect the power cable when you will not be using the product for an extended period of time. To reduce the power consumption to 0 watts when the power switch is not available, disconnect the power cable. 11 Specifications 81 11 Specifications 11.3 Standard Signal Mode Table This product can be set to only one resolution for each screen size to obtain the optimum picture quality due to the nature of the panel. Therefore, a resolution other than the specified resolution may degrade the picture quality. To avoid this, it is recommended that you select the optimum resolution specified for the screen size of your product. Check the frequency when you exchange a CDT monitor (connected to a PC) for an LCD monitor. If the LCD monitor does not support 85Hz, change the vertical frequency to 60Hz using the CDT monitor before you exchange it with the LCD monitor. If a signal that belongs to the following standard signal modes is transmitted from your PC, the screen will automatically be adjusted. If the signal transmitted from the PC does not belong to the standard signal modes, the screen may be blank even though the power LED turns on. In such a case, change the settings according to the following table by referring to the graphics card user manual. S23B550V Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 720 X 400 31.469 70.087 28.322 -/+ MAC, 640 x 480 35.000 66.667 30.240 -/- MAC, 832 x 624 49.726 74.551 57.284 -/- MAC, 1152 x 870 68.681 75.062 100.000 -/- VESA, 640 x 480 31.469 59.940 25.175 -/- VESA, 640 x 480 37.861 72.809 31.500 -/- VESA, 640 x 480 37.500 75.000 31.500 -/- VESA, 800 x 600 35.156 56.250 36.000 +/+ VESA, 800 x 600 37.879 60.317 40.000 +/+ VESA, 800 x 600 48.077 72.188 50.000 +/+ VESA, 800 x 600 46.875 75.000 49.500 +/+ VESA, 1024 x 768 48.363 60.004 65.000 -/- VESA, 1024 x 768 56.476 70.069 75.000 -/- VESA, 1024 x 768 60.023 75.029 78.750 +/+ VESA, 1152 x 864 67.500 75.000 108.000 +/+ VESA, 1280 x 720 45.000 60.000 74.250 +/+ VESA, 1280 x 800 49.702 59.810 83.500 -/+ VESA, 1280 x 1024 63.981 60.020 108.000 +/+ 11 Specifications 82 11 Specifications Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) VESA, 1280 x 1024 79.976 75.025 135.000 +/+ VESA, 1440 x 900 55.935 59.887 106.500 -/+ VESA, 1600 x 900 60.000 60.000 108.000 +/+ VESA, 1680 x 1050 65.290 59.954 146.250 -/+ VESA, 1920 x 1080 67.500 60.000 148.500 +/+ Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) 720 x 480,480p 31.470 59.940 27.000 +/+ 720 x 576,576p 31.250 50.000 27.000 +/+ 1280 x 720,720p 37.500 50.000 74.250 +/+ 1280 x 720,720p 45.000 60.000 74.250 +/+ 1920 x 1080,1080p 56.250 50.000 148.500 +/+ 1920 x 1080,1080p 67.500 60.000 148.500 +/+ Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 720 X 400 31.469 70.087 28.322 -/+ MAC, 640 x 480 35.000 66.667 30.240 -/- MAC, 832 x 624 49.726 74.551 57.284 -/- MAC, 1152 x 870 68.681 75.062 100.000 -/- VESA, 640 x 480 31.469 59.940 25.175 -/- VESA, 640 x 480 37.861 72.809 31.500 -/- VESA, 640 x 480 37.500 75.000 31.500 -/- VESA, 800 x 600 35.156 56.250 36.000 +/+ VESA, 800 x 600 37.879 60.317 40.000 +/+ VESA, 800 x 600 48.077 72.188 50.000 +/+ HDMI S27B550V 11 Specifications 83 11 Specifications Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) VESA, 800 x 600 46.875 75.000 49.500 +/+ VESA, 1024 x 768 48.363 60.004 65.000 -/- VESA, 1024 x 768 56.476 70.069 75.000 -/- VESA, 1024 x 768 60.023 75.029 78.750 +/+ VESA, 1152 x 864 67.500 75.000 108.000 +/+ VESA, 1280 x 720 45.000 60.000 74.250 +/+ VESA, 1280 x 800 49.702 59.810 83.500 -/+ VESA, 1280 x 1024 63.981 60.020 108.000 +/+ VESA, 1280 x 1024 79.976 75.025 135.000 +/+ VESA, 1440 x 900 55.935 59.887 106.500 -/+ VESA, 1600 x 900 60.000 60.000 108.000 +/+ VESA, 1680 x 1050 65.290 59.954 146.250 -/+ VESA, 1920 x 1080 67.500 60.000 148.500 +/+ Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) 720 x 480,480p 31.470 59.940 27.000 +/+ 720 x 576,576p 31.250 50.000 27.000 +/+ 1280 x 720,720p 37.500 50.000 74.250 +/+ 1280 x 720,720p 45.000 60.000 74.250 +/+ 1920 x 1080,1080p 56.250 50.000 148.500 +/+ 1920 x 1080,1080p 67.500 60.000 148.500 +/+ HDMI Horizontal Frequency The time required to scan a single line from the left to the right side of the screen is called a horizontal cycle. The reciprocal number of a horizontal cycle is called horizontal frequency. Horizontal frequency is measured in kHz. Vertical Frequency Repeating the same picture dozens of times per second allows you to view natural pictures. The repeat frequency is called "vertical frequency" or "refresh rate" and is indicated in Hz. 11 Specifications 84 Appendix Contact SAMSUNG WORLDWIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. NORTH AMERICA U.S.A 1-800-SAMSUNG (726-7864) http://www.samsung.com CANADA 1-800-SAMSUNG (726-7864) http://www.samsung.com/ca http://www.samsung.com/ca_fr (French) MEXICO 01-800-SAMSUNG (726-7864) http://www.samsung.com LATIN AMERICA ARGENTINA 0800-333-3733 http://www.samsung.com BRAZIL 0800-124-421 http://www.samsung.com 4004-0000 BOLIVIA 800-10-7260 http://www.samsung.com CHILE 800-SAMSUNG(726-7864) http://www.samsung.com From mobile 02-482 82 00 COLOMBIA 01-8000112112 http://www.samsung.com COSTA RICA 0-800-507-7267 http://www.samsung.com DOMINICA 1-800-751-2676 http://www.samsung.com ECUADOR 1-800-10-7267 http://www.samsung.com EL SALVADOR 800-6225 http://www.samsung.com GUATEMALA 1-800-299-0013 http://www.samsung.com HONDURAS 800-27919267 http://www.samsung.com JAMAICA 1-800-234-7267 http://www.samsung.com NICARAGUA 00-1800-5077267 http://www.samsung.com PANAMA 800-7267 http://www.samsung.com PERU 0-800-777-08 http://www.samsung.com PUERTO RICO 1-800-682-3180 http://www.samsung.com TRINIDAD & TOBAGO 1-800-SAMSUNG(726-7864) http://www.samsung.com VENEZUELA 0-800-100-5303 http://www.samsung.com Appendix 85 Appendix EUROPE ALBANIA 42 27 5755 http://www.samsung.com AUSTRIA 0810 - SAMSUNG (7267864, € 0.07/min) http://www.samsung.com BELGIUM 02-201-24-18 http://www.samsung.com/be (Dutch) http://www.samsung.com/be_fr (French) BOSNIA 05 133 1999 http://www.samsung.com BULGARIA 07001 33 11 http://www.samsung.com CROATIA 062 SAMSUNG (062 726 7864) http://www.samsung.com CZECH 800 - SAMSUNG (800-726786) http://www.samsung.com Samsung Electronics Czech and Slovak, s.r.o., Oasis Florenc, Sokolovská 394/17, 180 00, Praha 8 DENMARK 70 70 19 70 http://www.samsung.com FINLAND 030 - 6227 515 http://www.samsung.com FRANCE 01 48 63 00 00 http://www.samsung.com GERMANY 01805 - SAMSUNG (726-7864 € 0,14/Min) http://www.samsung.com CYPRUS From landline : 8009 4000 http://www.samsung.com GREECE From landline : 80111SAMSUNG (7267864) http://www.samsung.com From landline & mobile : (+30) 210 6897691 HUNGARY 06-80-SAMSUNG(726-7864) http://www.samsung.com ITALIA 800-SAMSUNG(726-7864) http://www.samsung.com KOSOVO +381 0113216899 http://www.samsung.com LUXEMBURG 261 03 710 http://www.samsung.com MACEDONIA 023 207 777 http://www.samsung.com MONTENEGRO 020 405 888 http://www.samsung.com NETHERLANDS 0900-SAMSUNG (0900-7267864) (€ 0,10/Min) http://www.samsung.com NORWAY 815-56 480 http://www.samsung.com POLAND 0 801-1SAMSUNG(172-678) http://www.samsung.com +48 22 607-93-33 Appendix 86 Appendix EUROPE PORTUGAL 808 20-SAMSUNG (808 20 7267) http://www.samsung.com RUMANIA From landline : 08010SAMSUNG (7267864) http://www.samsung.com From landline & mobile : (+40) 21 206 01 10 SERBIA 0700 Samsung (0700 726 7864) http://www.samsung.com SLOVAKIA 0800 - SAMSUNG (0800-726 786) http://www.samsung.com SPAIN 902 - 1 - SAMSUNG (902 172 678) http://www.samsung.com SWEDEN 0771 726 7864 (SAMSUNG) http://www.samsung.com SWITZERLAND 0848 - SAMSUNG (7267864, CHF 0.08/min) http://www.samsung.com/ch U.K 0330 SAMSUNG (7267864) http://www.samsung.com EIRE 0818 717100 http://www.samsung.com LITHUANIA 8-800-77777 http://www.samsung.com LATVIA 8000-7267 http://www.samsung.com ESTONIA 800-7267 http://www.samsung.com TURKEY 444 77 11 http://www.samsung.com http://www.samsung.com/ ch_fr/(French) CIS RUSSIA 8-800-555-55-55 http://www.samsung.com GEORGIA 8-800-555-555 http://www.samsung.com ARMENIA 0-800-05-555 http://www.samsung.com AZERBAIJAN 088-55-55-555 http://www.samsung.com KAZAKHSTAN 8-10-800-500-55-500 (GSM: 7799) http://www.samsung.com UZBEKISTAN 8-10-800-500-55-500 http://www.samsung.com KYRGYZSTAN 00-800-500-55-500 http://www.samsung.com TADJIKISTAN 8-10-800-500-55-500 http://www.samsung.com MONGOLIA http://www.samsung.com Appendix 87 Appendix CIS UKRAINE 0-800-502-000 http://www.samsung.com/ua http://www.samsung.com/ ua_ru BELARUS 810-800-500-55-500 http://www.samsung.com MOLDOVA 00-800-500-55-500 http://www.samsung.com ASIA PACIFIC AUSTRALIA 1300 362 603 http://www.samsung.com NEW ZEALAND 0800 SAMSUNG (0800 726 786) http://www.samsung.com CHINA 400-810-5858 http://www.samsung.com HONG KONG (852) 3698-4698 http://www.samsung.com/hk http://www.samsung.com/ hk_en/ INDIA 1800 1100 11 http://www.samsung.com 3030 8282 1800 3000 8282 1800 266 8282 INDONESIA 0800-112-8888 http://www.samsung.com 021-5699-7777 JAPAN 0120-327-527 http://www.samsung.com MALAYSIA 1800-88-9999 http://www.samsung.com PHILIPPINES 1-800-10-SAMSUNG (726-7864) for PLDT http://www.samsung.com 1-800-3-SAMSUNG(726-7864) for Digitel 1-800-8-SAMSUNG(726-7864) for Globe 02-5805777 SINGAPORE 1800-SAMSUNG (726-7864) http://www.samsung.com THAILAND 1800-29-3232 http://www.samsung.com 02-689-3232 TAIWAN 0800-329-999 http://www.samsung.com 0266-026-066 VIETNAM 1 800 588 889 http://www.samsung.com Appendix 88 Appendix MIDDlE EAST IRAN 021-8255 http://www.samsung.com OMAN 800-SAMSUNG(726-7864) http://www.samsung.com KUWAIT 183-2255 http://www.samsung.com BAHRAIN 8000-4726 http://www.samsung.com EGYPT 08000-726786 http://www.samsung.com JORDAN 800-22273 http://www.samsung.com MOROCCO 080 100 2255 http://www.samsung.com SAUDI ARABIA 9200-21230 http://www.samsung.com U.A.E 800-SAMSUNG (726-7864) http://www.samsung.com AFRICA CAMEROON 7095- 0077 http://www.samsung.com COTE D’ IVOIRE 8000 0077 http://www.samsung.com GHANA 0800-10077 http://www.samsung.com 0302-200077 KENYA 0800 724 000 http://www.samsung.com NIGERIA 0800-726-7864 http://www.samsung.com SENEGAL 800-00-0077 http://www.samsung.com SOUTH AFRICA 0860-SAMSUNG (726-7864) http://www.samsung.com TANZANIA 0685 88 99 00 http://www.samsung.com UGANDA 0800 300 300 http://www.samsung.com Appendix 89 Appendix Correct Disposal Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal. Appendix 90 Appendix Terminology OSD(On Screen Display) On screen display (OSD) allows you to configure on-screen settings to optimize the picture quality as required. It allows you to change the screen brightness, tint, size and many other settings using menus displayed on the screen. Gamma The Gamma menu adjusts the grey scale that represents middle tones on the screen. Adjusting the brightness brightens the whole screen, but adjusting Gamma only brightens the medium brightness. Grey scale Scale refers to levels of color intensity that show variations of color change from darker areas to brighter areas on the screen. Changes to the screen brightness are expressed with black and white variation, and grey scale refers to the medium area between black and white. Changing the grey scale through Gamma adjustment will change the medium brightness on the screen. Scanning rate Scanning rate, or refresh rate, refers to the frequency of screen refreshes. Screen data is transmitted as it refreshes to display an image, although the refreshing is invisible to the naked eye. The number of screen refreshes is called scanning rate and is measured in Hz. A scanning rate of 60Hz means that the screen refreshes 60 times per second. The screen scanning rate depends on the performance of the graphics cards in your PC and monitor. Horizontal Frequency Characters or images displayed on the monitor screen consist of numerous dots (pixels). Pixels are transmitted in horizontal lines, which are then arranged vertically to create an image. The horizontal frequency is measured in kHz and represents how many times horizontal lines per second are transmitted and displayed on the monitor screen. A horizontal frequency of 85 means that the horizontal lines that make up an image are transmitted 85 000 times per second, and the horizontal frequency is indicated in 85kHz. Vertical Frequency One image is made of numerous horizontal lines. The vertical frequency is measured in Hz and represents how many images can be created per second by those horizontal lines. A vertical frequency of 60 means that an image is transmitted 60 times per second. The vertical frequency is also called "refresh rate" and affects screen flicker. Appendix 91 Appendix Resolution Resolution is the number of horizontal pixels and vertical pixels that form a screen. It represents the level of display detail. A higher resolution displays a greater amount of information on the screen and is suitable for performing multiple tasks at the same time. E.g. A resolution of 1920 x 1080 consists of 1,920 horizontal pixels (horizontal frequency) and 1,080 vertical lines (vertical resolution). Plug & Play The Plug & Play feature allows the automatic exchange of information between a monitor and PC to produce an optimum display environment. The monitor uses VESA DDC (international standard) to execute Plug & Play. MHL (Mobile High-Definition Link) This feature allows you to enjoy videos and photos (imported from a connected mobile device that supports MHL) on the screen of the product. Appendix 92 Index Symbols G "MHL" (Mobile High-Definition Link) 27 Gamma 54 General 79 A Green 51 Appendix 85 Auto Source 65 H HDMI Black Level 48 B Before Connecting 31 I Blue 52 Image Size 56 Brightness 39 INFORMATION 68 Installation 23 C Checking the Contents 18 K Cleaning 3 Key Repeat Time 64 Coarse 45 Color Tone 53 Connecting and Using a PC 32 L Language 59 Contact SAMSUNG WORLDWIDE 85 Contrast 40 Copyright 2 Correct Disposal 90 Correct posture to use the product 12 D Display Time 66 M Menu Transparency 67 MultiScreen 72 O Off Timer OnOff 61 Off Timer Setting 62 E Eco Saving 60 P Parts 20 PC/AV Mode 63 F Fine 46 Q Q & A 77 Index 93 Index R Red 50 Requirements Before Contacting Samsung Customer Service Center 74 Reset 58 Response Time 47 S Safety Precautions 5 SAMSUNG MAGIC Angle 44 SAMSUNG MAGIC Bright 42 SAMSUNG MAGIC Color 49 Sharpness 41 Standard Signal Mode Table 82 U Using "MHL" 28 Index 94 ">

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- 68.6 cm (27") LED
- HD 1920 x 1080 pixels 16:9
- 2 ms 300 cd/m² 1000:1
- 40 W