V1.0
MCI-400
MUSIC CENTER WITH iPod DOCKING STATION, CASSETTE, FM RADIO, CD/MP3 PLAYER
AND USB- & CARDSLOT
INSTRUCTION MANUAL
For information and support, www.lenco.eu
LOCATION OF CONTROLS
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
11)
12)
CD DOOR
15) MAIN UNIT ON / OFF BUTTON
LCD DISPLAY
16) FUNCTION BUTTON
VOLUME UP/DOWN BUTTON
17) MEMORY/CLOCK ADJUST BUTTON
CD DOOR OPEN/CLOSE BUTTON
18) MP3 FOLDER UP/ PRE-UP
PRESE BUTTON
19) ST-MONO / PLAY/PAUSE
BUTTON
ALARM BUTTON
20) REMOTE SENSOR
PLAY MODE BUTTON
21) STANDBY LED INDICATOR
3.5MM STEREO HEADPHONE JACK
22) USB SOCKET
STOP
BUTTON
23) iPod DOCKING STATION
SKIP / TUNING UP
/DOWN
BUTTON
24) SD/MMC CARD SLOT
CASSETTE DECK DOOR
25) SPEAKER OUT TERMINAL (L/R)
CASSETTE CONTROL KEY
26) FM 75 OHM ANTENNA JACK
RECORD KEY
27) SUB-WOOFER OUT JACK
PLAYBACK KEY
28) AC POWER CORD OF MAIN UNIT
REWIND KEY
29) SUB-WOOFER VOLUME CONTROL
FAST FORWARD KEY
30) AC POWER CORD OF SUB-WOOFER UNIT
STO/EJECT KEY
31) SUB-WOOFER IN JACK
PAUSE KEY
13) CASSETTE KEY DUST COVER
14) SUB-WOOFER POWER ON/OFF BUTTON/INDICATOR
E-2
CAUTION:
USAGE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED
HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
THIS UNIT SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT QUALIFIED SERVICE PERSONNEL.
IMPORTANT:
SINCE MOVEMENT OF THE CD MECHANISM AND THE SENSITIVE CIRCUITY MAY CAUSE INTERFERENCE TO THE
RADIO TUNER NEARBY, SWITCH THIS UNIT OFF WHILE OPERATING OTHER RADIO DEVICES.
PRECAUTIONS FOR USE
INSTALLATION
•
•
•
UNPACK ALL PARTS AND REMOVE PROTECTIVE MATERIAL.
DO NOT CONNECT THE UNIT TO THE MAINS BEFORE CHECKING THE MAIN VOLTAGE AND BEFORE ALL OTHER
CONNECTIONS HAVE BEEN MADE.
DO NOT COVER ANY VENTS AND MAKE SURE THAT THERE IS A SPACE OF SEVERAL CENTIMETERS AROUND
THE UNIT FOR VENTILATION.
QUICK GUIDE CONNECTION
PLEASE FOLLOW THE FOLLOWING STEPS AND PROCEDURES TO SET UP YOUR MUSIC TOWER
I) MAIN UNIT + SUN-WOOFER CONNECTION
1)
2)
3)
PLACE THE MAIN UNIT VERTICALLY DOWN TO THE SUB-WOOFER TOP AS SHOW ON PICTURE
PULL THE MAUN UNIT BACKWARD UNIT THE BRACKET HOOK UP & TIGHTLY AS SHOW ON PICTURE
.
TRY TO LIFT UP THE WHOLE SYSTEM AND CHECK WHETHER THE MAIN UNIT & SUB-WOOFER ARE BEING
COMBINED TIGHTLY.
E-3
II) WIRE CONNECTION
1)
CONNECT THE END OF THE SPEAKER CABLE
TO THE SPEAKER OUT TERMINAL (RED & WHITE HEAD)
(25) AT THE BACK OF MAIN UNIT, ANOTHER
TERMINAL CONNECT TO THE SPEAKER CLIP OF THE
SPEAKER BOX BACK SIDE(RED COLOR OF SPEAKER
CABLE TO RED COLOR OF SPEAKER CLIP)
2)
CONNECT ONE END OF THE RCA CABLE (YELLOW
HEAD)
TO THE SUB-WOOFER OUT JACK (27) AT THE BACK OF
MAIN UNIT TO THE SUB-WOOFER IN JACK (31) AT THE
BACK OF THE SUB-WOOFER
3)
CONNECT THE 75 OHM ANTENNA JACK(26) VIA A 75
OHM
CABLE(NOT PROVIDED) TO GET THE FM RECEPTION
III) POWER SUPPLY
CONNECT THE AC POWER CORD FROM THE MAIN UNIT(28) AND AC POWER CORD FROM SUB-WOOFER UNIT(30)TO
THE MAIN POWER SUPPLY FROM YOUR HOME AREA. TURN ON THE ON/OFF BUTTON AT MAIN UNIT (15) AND POWER
ON THE SUB-WOOFER (14) RESPECTIVELY. IF THE LCD DISPLAY (2) AND THE POWER LED (14) IS LIGHT UP WITH
BLUE LIHGT. IT MEANS THE SYSTEM IS NOW READY TO PLAY THE MUSIC.
SETTING THE CLOCK
1.
2.
3.
4.
SET UNIT IN STANDBY MODE.
PRESS THE “MEM/CLK-ADJ” BUTTON (17) ONCE, THE LCD DISPLAY (2) WILL SHOW “ 24 HR “. PRESS SKIP
OR
SKIP
BUTTON (10) TO SELECT THE APPROPIATE AREA HOUR FORMAT(12HR/24HR). PRESS “MEM/CLK-ADJ”
BUTTON (17) AGAIN TO CONFIRM.
THEN FIRST DIGIT OF “0:00” ON DISPLAY(2)(IF SELECT 24HS MODE) IS FLASHING. PRESS SKIP
OR SKIP
BUTTON (10) TO SET THE CORRECT HOUR. PRESS ”MEM/CLK-ADJ” BUTTON (17) TO STORE THE CORRECT
HOUR.
THE THIRD & FOURTH DIGIT OF “0:00” IS FLASHING, PRESS THE SKIP
OR SKIP
BUTTON (10) TO SET THE
CORRECT MINUTES. THEN PRESS “MEM/CLK-ADJ” (17) TO STORE THE CORRECT MINUTE.
THE PRE-SET TIME WILL BE RE-SET COMPLETELY IF DIS-CONNECTING THE MAIN POWER SUPPLY.
YOU ARE RECOMMENDED TO SWITCH THE SYSTEM INTO STANDBY MODE FOR CONVENIENCE
USAGE.
LISTENING TO RADIO
MANUAL TUNING
1.
2.
3.
PRESS FUNCTION BUTTON (16) TO SELECT “ TUNER ” MODE.
TUEN TO THE DESIRE STATION BY PRESSING THE SKIP/TUNE
OR SKIP/TUNE
BUTTON (10).
ADJUST THE MAIN VOLUME CONTROL (3) AND SUB-WOOFER VOLUME (29) TO THE DESIRED VOLUME AND BASS
EFFECT LEVEL.
AUTO TUNING
1.
2.
3.
4.
5.
PRESS FUNCTION BUTTON (16) TO SELECT “ TUNER ” MODE.
PRESS AND HOLD THE SKIP/TUNE
OR SKIP/TUNE
BUTTON (10) FOR 1-2 SECONDS AND THEN
RELEASE.
THE UNIT WILL START SEEKING AUTOMATICALLY AND STOP UNTIL A RADIO STATION IS REACHED.
REPEAT STEP 3 & 4 UNTIL THE DESIRED RADIO STATION IS BEING REACHED.
ADJUST THE MAIN VOLUME CONTROL (3) AND SUB-WOOFER VOLUME (29) TO THE DESIRED VOLUME AND BASS
EFFECT LEVEL.
E-4
PRESET STATIONS
YOU CAN STORE UP TO 20 RADIO STATIONS IN THE MEMORY (20 FM).
1. SET TO TUNER MODE.
2. TURN TO THE DESIRED RADIO STATION BY “ MANUAL” OR “ AUTO ” TUNING METHOD.
3. PRESS “ MEM/CLK-ADJ ” BUTTON (17) TO ENABLE PROGRAM FUNCTION & “ MEM ” INDICATOR IS SHOW ON LCD
(2)
4. PRESS “ FOLDER / PRE-UP ” BUTTON (18) TO SELECT THE DESIRED STATION MEMORY FOR STORAGE.
5. PRESS “MEM/CLK-ADJ” BUTTON (17) AGAIN TO CONFIRM THE SETTING.
6. REPEAT STEP 2 TO 5 TO STORE OTHER STATIONS.
7. NOW YOU CAN SELECT THE PRESETS STATIONS IN ORDER BY PRESSING THE “FOLDER/REP-UP” BUTTON (18)
OR PRE-DN
BUTTON (ON REMOTE HANDSET)
THE PRE-SET MEMORIES WILL BE CANCELLED COMPLETELY IF DIS-CONNECTING THE MAIN POWER SUPPLY.
YOU ARE RECOMMENDED TO SWITCH THE SYSTEM INTO STANDBY MODE FOR CONVENIENCE USAGE.
THERE ARE 10 SECONDS FOR PROGRAM STATE, AFTER 10 SEC. THIS STATE WOULD RESUME TO NORMAL
TUNER MODE AUTOMATICALLY.
YOU CAN OVERWRITE A PRESENT STATION BY STORING ANOTHER FREQUENCY IN ITS PLACE.
FM & FM-STEREO RECEPTION (BY REMOTE HANDSET)
PRESS THE “ST-MO“ BUTTON(19) OR “FM-ST / MONO”. ” BUTTON AT REMOTE HANDSET REPEATEDLY, THE FM
PROGRAMS ARE RECEIVING IN MONO AND STEREO MODE REPEATEDLY. IN PARTICULAR WHEN STEREO
SIGNALS ARE WEAK. IT IS PREFERABLE TO RECEIVE THE PROGRAM IN MONO.
IF STEREO SIGNAL IS BEING RECEIVED, THE “ST” INDICATOR “
” WILL APPEAR ON LCD (2) TO SHOW FM
STEREO PROGRAM IS NOW RECEIVING.
HINTS FOR BEST RECEPTION:FM : CONNECT THE FM SOCKET (26) VIA A 75 OHM CABEL (NOT PROVIDED) FOR THE BEST RECEPTION.
PLAYING COMPACT DISC
GETTING START
1.
2.
3.
PRESS FUNCTION BUTTON (16) TO SELECT “ CD ” MODE,
PRESS “CD DOOR OPEN/CLOSE” BUTTON (4) TO OPEN THE CD DOOR.
PLACE A CD INSIDE THE TRAY WITH THE PRINTED SIDE FACING OUT & THEN CLOSE THE CO DOOR BY
PRESSING THE “ CD DOOR OPEN/CLOSE “ BUTTON (4) AGAIN.
FOCUS SEARCH IS PERFORMING, THE LCD DISPLAY (2) WILL SHOW THE TOTAL NUMBER OF TRACKS & TOTAL
PLAYING TIME.
4.
PLAY / PAUSE MODE
1.
2.
PRESS THE “ST/MO/ ” BUTTON (19) TO START PLAYBACK, THE FIRST TRACK WILL START PLAYBACK.
TO INTERRUPT, PRESS THE “ST/MO/ ” BUTTON (19) ONCE, AND THE PLAYING TIME WILL BE FREEZE &
FLASHING ON THE LCD DISPLAY (2). PRESS AGAIN TO RESUME NORMAL PLAYBACK.
STOP MODE
1.
IF “STOP
SKIP MODE (SKIP UP
1.
DURING PLAY OR PAUSE MODE, IF “SKIP UP
” BUTTON (10) IS PRESSED. IT WILL GO TO NEXT TRACK AND
DISPLAY THE TRACK NO. AND THEN REMAIN THE PLAY OR PAUSE MODE.
DURING PLAY OR PAUSE MODE, IF “SKIP DOWN
” BUTTON (10) IS PRESSED. IT WILL GO BACK TO THE
BEGINNING OF THE TRACK, ORIGINAL TRACK NO. IS DISPLAY AND REMAIN THE PLAY OR PAUSE MODE.
AFTER STEP 2, PRESS “SKIP DOWN
” BUTTON (10) AGAIN WILL GO TO THE PREVIOUS TRACK AND REMAIN
THE PLAY OR PAUSE MODE.
2.
3.
“ BUTTON (9) IS PRESSED DURING PLAY OR PAUSE MODE, SYSTEM WILL GO TO STOP MODE.
/ SKIP DOWN
)
FOR MP3 DISC
1.
AFTER FOCUS SEARCH IS PERFORMING, THE TOTAL NUMBER OF TRACK AND ABLUM WILL BE SHOWN ON THE
LCD DISPLAY (2).
PRESS “ FOLDER/ PRE-UP “ (18) TO SELECT THE ALBUM NUMBER.
PRESS “ SKIP UP
“ OR SKIP DOWN
(10) BUTTON TO SELECT THE TRACK NUMBER.
WHEN THE DESIRED TRACK AND ALBUM IS BEING SELECTED, PRESS THE “ST/MO/ ” BUTTON (19) TO START
PLAYBACK.
2.
3.
4.
E-5
ID3 (TRACK/ALBUM TITLE) FUNCTION (BY REMOTE HANDSET)
PRESS THE “ ID3 “ BUTTON UNTIL THE LCD DISPLAY (2) SHOW “ FILE - … ”DURING PLAYBACK OF MP3/WMA FILE,
THE SONG TITLE / ARTIST NAME / ALBUM NAME IS BEING DISPLAYED IN SEQUENCE . PRESS THE “ ID3 ” BUTTON
AGAIN TO DISABLE THE FUNCTION.
REMARK:-
IN THAT CASE OF NO NAME HAD BEEN ASSIGNED FOR THE TRACK, “ NO TITLE “ OR “ NO ARTIST “ IS BEING
DISPLAYED” ON LCD DISPLAY (2).
- NO TITLE/ALBUM NAME CAN BE RECOGNIZED IF THE INPUT FORMAT ON THE DISC/MASS MEDIA IS NOT
SUPPORTING BY THE SYSTEM.
- THE SYSTEM SUPPORT ONLY ENGLISH TEXT FOR ID3 FUNCTION
MP3 TRACK FORMAT REQUIREMENT:- BIT RATE : 32 KBPS~320KBPS, SAMPLING RATE : 32KHZ, 44.1KHZ AND 48 KHZ DECODABLE
- THE PERFORMANCE OF PLAYING MP3 DISC IS VARIOUS FROM THE QUALITY OF RECORDING DISC AND THE
METHOD OF RECORDING. FURTHERMORE, THE SEARCHING LEAD-TIME FOR MP3-CD IS LONGER THAN NORMAL
CD DUE TO DIFFERENCE FORMAT.
REPEAT/RANDOM MODE
PRESS THE “ PLAT MODE “ BUTTON (7)DURING PLAYBACK TO SELECT REPEAT AND RANDOM FUNCTION, A SINGLE
TRACK, SINGLE FOLDER (MP3 ONLY) OR ALL THE TRACKS CAN BE PLAYED IN DIFFERENCE MODE AS FOLLOW:-
FOR CD
(1) REPEAT 1
(2) REPEAT ALL TRACK
PLAY MODE
REPEAT TRACK
REPEAT ALL
RANDOM
OFF MODE
(3) RANDOM
(4) OFF MODE
INDICATOR
ON LCD DISPLAY
& FLASHING
RAN
--------------
FOR MP3/WMA DISC/FILE
(1) REPEAT 1
(2) REPEAT 1 FOLER
(3) REPEAT ALL TRACKS
(5) OFF MODE
PLAY MODE
REPEAT SINGLE TRACK
REPEAT SINGLE FOLDER
REPEAT ALL TRACKS
RANDOM MODE
OFF MODE
(4) RANDOM
INDICATOR
ON LCD DISPLAY
& FLASHING
RAN
-----------------
REPEAT PLAY
YOU CAN LISTEN THE DESIRED TRACKS OR FOLDER REPEATEDLY BY THIS FUNCTION.
RANDOM PLAY
YOU CAN LISTEN ALL THE TRACKS OR FOLDER IN A RANDOM ORDER BY THIS FUNCTION
CD / MP3 DISC PROGRAMMING
UP TO 20 TACKS CAN BE PROGRAMMED FOR DISC PLAY IN THIS FUNCTION. BEFORE USE, BE SURE TO PRESS THE
“ STOP
“ BUTTON (9)
1. SET IN CD MODE & STOP THE CD OR CD-MP3 PLAYBACK.
2. PRESS THE “MEMORY/CLK-ADJ” BUTTON (17) , “ MEM “ WILL FLASH ON LCD DISPLAY (2). MOREOVER, IT WILL
INDICATE PROGRAM NO. AND DIGITS FOR TRACK NO. TO BE PROGRAMMED – “ 0 P- 01 “.
3. SELECT A DESIRED TRACK BY PRESSING SKIP UP
OR DOWN
BUTTONS (10).
4. PRESS THE“MEMORY/CLK-ADJ” BUTTON (17) TO STORE THE TRACK INTO MEMORY.
E-6
5.
6.
7.
REPEAT STEPS 3 AND 4 TO ENTER ADDITIONAL TRACKS INTO THE MEMORY IF NECESSARY.
WHEN ALL THE DESIRED TRACKS HAVE BEEN PROGRAMMED, PRESS ST/MONO ” BUTTON (19) TO PLAY THE
DISC IN ASSIGNED ORDER.
PRESS “STOP ” BUTTON (9) TO TERMINATE PROGRAM PLAY.
AFTER PROGRAM COMPLETE, PRESS “MEMORY/CLK-ADJ” BUTTON (17)TO REVIEW THE TRACKS BEING
PROGRAMMED.
PRESS “ STOP
“ BUTTON (9) AT CD STOP MODE TO CANCEL ALL PROGRAMMED MEMORY.
ST
FOR MP3 DISC / FILE, PRESS THE “ FOLDER / PRE-UP “ BUTTON (18) TO SELECT THE 1 TRACK OF NEXT
FOLDER DIRECTLY AND HENCE TO SPEED UP THE SONG SLECTION.
LISTENING TO iPod
CONNECTING
BEFORE FITTING ANY DOCKABLE iPod MODEL ON THE DOCKING STATION (23) OF
THE SYSTEM, PLEASE SELECT AND INSERT THE PROPER DOCKING CRADLE WHICH
SUPPLIED WITH YOUR PARTICULAR iPod MODEL DURING PURCHASES OR
PURCHASED SEPARATELY.
REMARK :
DO NOT INSERT WRONG DOCKING CRADLE AS IT MAY CAUSE A MALFUTION OF
THE iPod AND THE SYSTEM.
THEN INSERT YOUR iPod AFTER INSERTING THE APPROPIATE DOCK ADAPTOR.
PLAYBACK
1.
PRESS FUNCTION BUTTON (16) TO SELECT “ iPod ” MODE. THE TEXT “ iPod ” WILL APPEAR ON THE LCD DISPLAY
(2).AND THE SYSTEM WILL START PLAYBACK AUTOMATICALLY OR PRESS “ PLAY/PAUSE
” BUTTON (19) TO
START PLAYBACK.
PRESS THE SKIP UP
OR DOWN
BUTTON (10) TO SELECT THE DESIRE MUSIC TRACK.
ADJUST VOLUME UP/DOWN CONTROL (3) AND SUB-WOOFER VOLUME (29) TO THE DESIRE VOLUME AND BASS
EFFECT LEVEL.
2.
3.
CHARGING
WHEN THE iPod IS DOCKED ON THE UNIT, THE BATTERY CAN BE CHARGED IN ALL FUNCTIONS MODE EXCEPT
TUNER MODE.
iPod CONTROL FUNCTION KEYS (BY REMOTE CONTROL)
YOU ARE RECOMMENDED TO CONTROL THE iPod UNIT BY USING FOLLOWING “ i-MENU ” BUTTONS INSTEAD OF
PRESSING THE iPod UNIT DIRECTLY AFTER DOCKING ON THE SYSTEM.
4)
5)
6)
PRESS “ i-MENU ” BUTTON TO CONTROL THE iPod MENU FUCNTION OF YOUR iPod UNIT.
PRESS “ i-SCROLL ” BUTTON TO CONTROL THE SCROLL UP/DOWN FUNCTION OF YOUR iPod UNIT.
PRESS “ i-ENTER ” BUTTON TO CONTROL THE ENTER FUNCTION OF YOUR iPod UNIT.
REMARK :
7)
8)
9)
TO PREVENT DAMAGE OF THE DOCK CONNECTOR, DON’T TWIST THE iPod WHEN INSERTING OR REMOVING IT.
BE CAREFUL NOT TO KNOCK OVER THE iPod WHEN INSERTED TO PREVENT DOCK CONECTOR DAMAGE.
DON’T USE WITH ANY OTHER iPod ACCESSORIES, SUCH AS FM TRANSMITTERS AND MICROPHONES BECAUSE
THEY MAY CAUSE A MALFUNCTION.
LISTENING TO TAPE
GENERAL OPERATION
STOP / EJECT KEY
FAST FORWARD
& FAST REWIND
PLAY
PAUSE
RECORD
KEY
KEY
KEY
PRESS TO STOP ALL DECK OPERATION. PRESS AGAIN TO OPEN THE CASSETTE DOOR.
KEY PRESS TO START RAPID TAPE WINDING IN EITHER FORWARD OR REVERS
KEY DIRECTION. PRESS STOP/EJECT KEYS WHEN THE CASSETTE SPOOLS STOP TURNING.
PRESS TO START PLAYING TAPE.
PRESS TO STOP TAPE OPERATION TEMPORARILY. PRESS AGAIN TO RESUME PLAY.
PRESS TOGETHER WITH PLAY KEY TO START TAPE RECORDING.
E-7
PLAYBACK
SELECT “TAPE” FUNCTION (16).
PUT IN THE CASSETTE TAPE.
PRESS “
PLAY “ KEY TO ACTIVE PLAYBACK
ADJUST THE VOLUME AT MAIN UNIT (3) AND SUB-WOOFER (29 ) TO THE DESIRE LEVEL.
USE PAUSE KEY WHEN YOU WANT TO STOP PLAYBACK TEMPORARILY.
PRESS STOP / EJECT KEY WHEN FINISHED.
RECORDING
THE CASSETTE DECK CAN RECORD ALL FUNCTIONS MODEL (CD/TUNER/USB/SD/iPod) AS FOLLOWING
PROCEDURES:
SELECT THE FUNCTION WHICH YOU WANT TO RECORD TO CASSETTE TAPE.
INSERT A BLANK CASSETTE TAPE IN CASSETTE DECK.
PRESS “ RECORD” & “ PLAY “ KEY TO START RECORDING.
START THE PLAYBACK OF THE MUSIC SOURCE WHICH YOU WANT TO RECORD TO TAPE
PRESS “PAUSE” KEYS AND THEN “STOP/EJECT” KEY AT CASSETTE DECK WHEN FINISH.
PLAYBACK OF MP3/WMA SONG VIA USB STORAGE MEDIA OR MEMORY CARD
CONNECTING
THE SYSTEM IS ABLE TO DECODE AND PLAYBACK ALL MP3 FILE WHICH STORED IN
THE MEMORY MEDIA WITH USB CONNECTING PORT, MULTI- MEDIA CARD (MMC)
OR SECURE DIGITAL (SD) MEMORY CARD.
1.
2.
OR CARD
” MODE.
PRESS FUNCTION BUTTON (16) TO SELECT “ USB
PLUG-IN THE USB PLUG WITH THE FACE UP & MAKE SURE IT GOING INTO
COMPLETELY OR INSERT THE MEMORY CARD IN THE DIRECTION OF THE
ARROW AS SHOWN IN THE LABEL ON THE UNDERSIDE OF THE MEMORY CARD
SLOT COVER. INSERT STRAIGHT WITHOUT BENDING.
CONNECTING THE USB / MEMORY CARD UPSIDE DOWN OR BACKWARDS COULD DAMAGE THE AUDIO
SYSTEM OR THE STORAGE MEDIA (USB / MEMORY CARD). CHECK TO BE SURE THE DIRECTION IS CORRECT
BEFORE CONNECTION.
THE SYSTEM WILL START READING THE STORAGE MEDIA AUTOMATICALLY AFTER CONNECTING, AND LCD
DISPLAY (2) WILL SHOW THE TOTAL NUMBER OF MP3/WMA FILES AND TOTAL NUMBER OF ALBUM BEING
DETECTED.
REPEAT THE SAME PLAYBACK PROCEDURE AS PLAYING CD/MP3 DISC AS ABOVE
3.
4.
REMARK
-
-
THE SYSTEM CAN DETECT AND READ THE FILE UNDER MP3 AND WMA FORMAT ONLY THROUGH THE USB
PORT/MEMORY CARD SLOT.
IF CONNECT THE SYSTEM TO MP3 PLAYER VIA THE USB SOCKET, DUE TO VARIANCES IN MP3 ENCODING
FORMAT, SOME MP3 PLAYER MAY NOT BE ABLE TO PLAY VIA THE USB SOCKET. THIS IS NOT THE
MALFUNCTION OF THE SYSTEM.
USB PORT DOES NOT SUPPORT CONNECTION WITH USB EXTENSION CABLE AND IS NOT DESIGNED FOR
COMMUNICATION WITH COMPUTER DIRECTLY.
REMOVING OF USB / MEMORY CARD
TO REMOVE THE USB / MEMORY CARD, TURN OFF THE UNIT OR SWITCH THE FUNCTION MODE TO EITHER CD, OR
TUNER FIRST. FOR USB PORT – UN-PLUG IT BY PULLING OUT THE USB SOCKET DIRECTLY, FOR MEMORY CARD –
PRESS THE MEMORY CARD INWARD & THEN RELEASE, NOW THE CARD BEING PARTIALLY EJECT AND YOU CAN
REMOVE IT BY HAND.
MORE FEATURES
A.
1.
2.
3.
4.
SLEEP SETTING (BY REMOTE CONTROL)
PRESS “SLEEP” BUTTON AND SLEEP INDICATOR SHOWN ON THE LCD (2).
KEEP PRESSING THE BUTTON TO ADJUST THE SLEEP TIMER IN THE ORDER OF 90 > 75 >60….15 MINUTES.
SYSTEM WILL STOP AND GOTO STANDBY MODE AUTOMATICALLY AFTER THE SELECTED TIMING.
TO CANCEL THE SLEEP MODE, PRESS “ SLEEP ” BUTTON UNIT IT REACHS “OFF” MODE.
E-8
B.
ALARM CLOCK SETTING (BY REMOTE CONTROL)
THIS FUNCTION ALLOWS THE SYSTEM TO TURN ON AUTOMATICALLY AND WAKE YOU UP BY CD, TUNER, USB, SD or
iPod MODE RESPECTIVELY.
FIRST, SET THE UNIT AT STANDBY MODE AND THEN PRESS AND HOLD FOR A WHILE THE “ ALARM ” BUTTON (6) TO
ENTER THE SETTING MODE, THE FIRST TWO DIGITS OF CLOCK AND INDICATOR “
”WILL FLASHING:
1) WAKE UP TIME : THEN PRESS SKIP UP
/ DOWN
” BUTTON (10) TO SET THE HOUR & THEN PRESS “ ALARM ”
BUTTON (6) AGAIN TO CONFIRM. THEN PRESS SKIP UP
/ DOWN
” BUTTON (10) TO SET
THE MINUTES & THEN PRESS THE “ ALARM “ BUTTON(6) TO CONFIRM.
1) WAKE UP SOURCE : PRESS THE “SKIP UP
/ DOWN
” BUTTON (10) TO SELECT THE SOURCE FROM “CD” -
“ - “ USB
” - “ TUNER” – “ iPOD ” REPEATLY. PRESS “ ALARM“ BUTTON(6)
“SD/MMC
AGAIN TO CONFIRM SELECTED THE SOURCE .
2) WAKE UP VOLUME : PRESS SKIP UP
/ DOWN
” BUTTON (10) TO SET THE WAKE UP VOLUME LEVEL FROM 1
TO MAX. AND THEN PRESS “THE ALARM” BUTTON(6) TO CONFIRM
NOW THE ALARM SETTING IS COMPLETED AND THE ALARM INDICATOR “
”
IS SHOWN ON LCD.
REMARK
IF THERE IS NO MUSIC SOURCE BEING DETECTED (SUCH AS CD) WHEN THE PRESET TIME IS REACHED,
SYSTEM WILL DEFAULT TO “ TUNER ” FOR WAKE UP MODE AUTOMATICALLY.
FOR TUNER WAKE UP, THE SYSTEM WILL PRESET AT THE LATEST RADIO FRQUENCY BEING LISTENED
BEFORE SWITCHING OFF.
ACTIVE/DE-ACTIVE ALARM FUNCTION
1.
TO ACTIVE THE ALARM, PRESS THE “ ALARM ” BUTTON(6) UNTIL THE ALARM INDICATOR “
ON LCD DISPLAY (2).
”
IS SHOWN
2.
TO CANCEL ALARM FUNCTION BY PRESS AGAIN “ ALARM ” BUTTON(6) UNTIL THE TIMER INDICATOR “
DISAPPEAR.
SNOOZE FUNCTION
”
PRESS “ SNOOZE ” BUTTON ON REMOTE CONTROL ONCE TO TERMINATE THE ALARM MODE TEMPORARILY, AND
SYSTEM WILL RE-START AGAIN AFTER 10 MINUTES ON EACH PRESS. TO CANCEL THE ALARM MODE, PRESS THE
“ ALARM ” (6)BUTTON OR “ POWER ON/STANDBY
” BUTTON (15) WHILE SYSTEM IS ON.
C. MUTE FUNCTION (BY REMOTE HANDSET)
PRESS TO TERMINATE THE SOUND OUTPUT FROM SPEAKER TEMPORARILY AND PRESS AGAIN TO RESUME SOUND
OUTPUT.
D. PRE-SET EQ FUNCTION (BY REMOTE CONTROL)
THIS UNIT PROVIDES 4 DIFFERENCES SOUND MODE TO ENHANCE YOUR LISTENING EXPERIENCE. YOU CAN
SELECT THE DESIRED EFFECT BY PRESSING THE “ PRESET EQ” BUTTON REPEATEDLY AT FOLLOWING SEQUENCE:-
FLAT
CLASSIC
ROCK
POP
E-9
JAZZ
REMOTE CONTROL TRANSMITTER
CONTROL FUNCTIONS
BATTERY INSTALLATION
THE INFRA-RED TRANSMITTER REQUIRE 2 PCS “ AAA “ BATTERY FOR OPERATION
BUTTON DESCRIPTION
1) POWER ON/STANDBY
PRESS TO SWITCH ON/STANDBY THE SYSTEM
2) MEMORY/CLK-ADJ
IN CD MODE : PRESS TO ACTIVE CD ROGRAM FUNCTION
IN TUNER MODE : PRESS TO ACTIVE PRESET STATION MODE
IN STANDBY MODE : PRESS TO ADJUST CLOCK
3) PLAY/PAUSE
IN CD/USB/SD/iPod MODE : PRESS ONCE TO START CD PLAYBACK. PRESS ONCE
AGAIN TO STOP THE MUSIC PLAY TEMPORARILY
IN FM TUNER MODE : PRESS TO SELECT FM STEREO OR MONO
/ ST/MO
4) SKIP/TUNE DOWN
5) FOLDER/PRE DOWN
i-MENU
6) i-SCROLL
7) VOLUME
/-10
-/+
IN CD/USB/SD/iPod MODE : TO SELECT PREVIOUS TRACK
IN TUNER MODE : PRESS TO STEP DOWN OF FREQUENCY
/
IN MP3 MODE : PRESS TO STEP DOWN THE MP3 FOLDER
IN TUNER MODE : PRESS TO SELECT THE PRESET MEMORY DOWN
IN IPOD MODE : PRESS TO CONTROL MENU FUNCTION OF iPod UNIT
PRESS TO CONTROL SCROLL FUNCTION OF iPod UNIT
IN CD/USB/SD MODE : PRESS TO SKIP -10 TRACKS
IN IPOD MODE : PRESS TO CONTROL SCROLL FUNCTION OF iPod UNIT
PRESS TO ADJUST VOLUME LEVEL UP/DOWN
E-10
8) i-SHUFFLE
IN iPod MODE : PRESS TO CONTROL SHUFFLE FUNCTION OF iPod UNIT
9) SLEEP
PRESS TO ACTIVE SLEEP FUNCTION
10) ALARM
PRESS TO ON/OFF AND SETTING THE ALARM FUNCTION
11) SNOOZE
IN ALARM MODE: PRESS ONCE TO ACTIVE SNOOZE FUNCTION AND PRESS TO
12) ID3
IN CD MP3/USB/SD MODE: PRESS TO ACTIVE/DE-ACTIVE ID3 FUNCTION
13) MUTE
PRESS TO ACTIVE MUTE FUNCTION
14) PRESET EQ
PRESS TO SELECT DIFFERENCE EQ MODE FOR LISTENING ENJOYMENT
15) i-REPEAT/PLAY MODE
IN iPod MODE : CONTROL REPEAT FUNCTION OF iPod UNIT
IN CD/MP3 MODE: PRESS TO ACTIVE REPEAT AND RANDOM PLAY FUNCTION
16) CD DOOR OPEN/CLOSE
PRESS TO OPEN AND CLOSE THE CD DOOR
17) i-SCROLL UP /
+10
IN CD/USB/SD MODE : PRESS TO SKIP -10 TRACKS
IN IPOD MODE : PRESS TO CONTROL SCROLL FUNCTION OF iPod UNIT
18) FODER/PRE UP /
i-ENTER
IN MP3 MODE : PRESS TO STEP UP THE MP3 FOLDER
TUNER MODE : PRESS TO SELECT THE PRESET MEMORY UP
IN IPOD MODE : PRESS TO CONTROL ENTER FUNCTION OF iPod UNIT
19) STOP
IN CD/USB/SD MODE : PRESS TO STOP THE CD/USB/SD PLAYING
20) SKIP/TUNE UP
IN CD/USB.SD/iPod MODE : TO SELECT NEXT TRACK
IN TUNER MODE : PRESS TO STEP UP OF FREQUENCY
21) FUNCTION
PRESS TO SELECT THE FUNCTIONS (CD/TUNER/BLUETOOTH/USB/SD/AUX)
E-11
">
