Advertisement
Advertisement
NETWORK CAMERA User Manual SND-3080(P) Network Camera User Manual Copyright ©2010 Samsung Techwin Co., Ltd. All rights reserved. Trademark is the registered logo of Samsung Techwin Co., Ltd. The name of this product is the registered trademark of Samsung Techwin Co., Ltd. Other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin. Disclaimer Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. Samsung Techwin reserves the right to change the contents of this document without prior notice. Warranty If the product does not operate properly in normal conditions, please let us know. Samsung Techwin will resolve the problem for free of charge. The warranty period is 3 years. However, the followings are excluded: • If the system behaves abnormally because you run a program irrelevant to the system operation. • Deteriorated performance or natural worn-out in process of time overview CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit. WARNING y To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. y To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions. y If this power supply is used at 24V ac, a suitable plug adapter should be used. y The camera is to be only connected to PoE networks without routing to the outside plant. WARNING 1. Be sure to use only the standard adapter that is specified in the specification sheet. Using any other adapter could cause fire, electrical shock, or damage to the product. 2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire, electric shock, or damage to the product. 3. Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause abnormal heat generation or fire. 4. Securely plug the power cord into the power receptacle. Insecure connection may cause fire. 5. When installing the camera, fasten it securely and firmly. The fall of camera may cause personal injury. 6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers filled with water on top of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects. English _3 ● OVERVIEW CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER overview 7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock. 8. If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the power source and contact the service center. Continued use in such a condition may cause fire or electric shock. 9. If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifications or attempted repair.) 10. When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock 11. Do not expose the product to the direct airflow from an air conditioner. Otherwise, it may cause moisture condensation inside the Clear Dome due to temperature difference between internal and external of the dome camera. 12. If you install this product in a low-temp area such as inside a cold store, you must seal up the wiring pipe with silicon, so that the external air can not flow inside the housing. Otherwise, external high, humid air may flow inside the housing, pooling moisture or vapor inside the product due to a difference between internal and external temperature. 4_ overview CAUTION 1. Do not drop objects on the product or apply strong blows to it. Keep away from a location subject to excessive vibration or magnetic interference. 2. Do not install in a location subject to high temperature (over 50°C), low temperature (below -10°C), or high humidity. Doing so may cause fire or electric shock. 3. If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall it. 5. Keep out of direct sunlight and heat radiation sources. It may cause fire. 6. Install it in a place with good ventilation. 7. Avoid aiming the camera directly towards extremely bright objects such as sun, as this may damage the CCD image sensor. 8. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. 9. The Mains plug is used as a disconnect device and shall stay readily operable at any time. 10. When using the camera outdoors, moisture may occur inside the camera due to temperature difference between indoors and outdoors. For this reason, it is recommended to install the camera indoors. For outdoor use, use the camera with builtin fan and heater. English _5 ● OVERVIEW 4. Remove the power plug from the outlet when there is a lighting storm. Neglecting to do so may cause fire or damage to the product. overview FCC STATEMENT This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions : 1) This device may not cause harmful interference, and 2) This device must accept any interference received including interference that may cause undesired operation. CAUTION This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. IC Compliance Notice This Class A digital apparatus meets all requirements of the Canadian Interference.-Causing Equipment Regulations of ICES-003. CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. 6_ overview IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus English _7 ● OVERVIEW 6. Clean only with dry cloth. overview CONTENTS 7 10 10 11 12 Important Safety Instructions Product Features Recommended PC Specifications What’s Included At a Glance INSTALLATION & CONNECTION 16 17 16 18 19 21 Removing the Covers Inserting/Removing an SD Memory Card Memory Card Information (Not Included) Connecting with Other Device Installation CAMERA SETUP 24 25 25 26 31 32 33 How to Use the Keyboard Controller Main Menu Profile Camera Setup Privacy Zone Others System Info 34 Connecting the Camera to an IP Router with the xDSL/Cable Modem Connecting the Camera to an IP Router With Local Area Networking Connecting the Camera Directly to a DHCP-Based xDSL/Cable Modem Connecting the Camera Directly to Local Area Networking Buttons Used in IP Installer Static IP Setup Dynamic IP Setup Port Range Forward (Port Mapping) Setup Connecting to the camera from a shared local PC Connecting to the camera from a remote PC via the Internet OVERVIEW 3 24 NETWORK CONNECTION AND SETUP 34 35 36 37 38 39 42 43 44 44 8_ overview WEB VIEWER 45 52 APPENDIX 70 Connecting to the Camera Login Installing Activex Using the Live Screen Backup Using the SD Search Viewer Screen 52 53 58 61 62 69 Accessing the Setup Screen Default Setup System Setup Overlay Setup Event Setup Network Setup 70 71 72 76 82 88 90 Profile Terminology Specifications Frame Rate (NTSC) Frame Rate (PAL) Troubleshooting GPL/LGPL Software License English _9 ● OVERVIEW SETUP SCREEN 45 46 47 48 49 51 overview PRODUCT FEATURES y Support various communication protocols Supports TCP/IP, UDP, RTP/RTSP, SMTP for email, and FTP protocols as well as various internet protocols such as ARP, HTTP, HTTPS and DHCP. y Web Browser-based Monitoring Using the Internet web browser to display the image in a local network environment. y Automatic Local IP Setup Even a network novice can install it with minimum operations. y Alarm If an alarm sensor is connected and it detects a motion, a message is sent to the registered address via FTP/email (SMTP) or stored in the SD memory card, or an alarm will signal to the alarm out terminal. y Motion Detection If the camera with a specified motion area detects a motion in that area, it will send a notification to a user FTP/email account (SMTP) or stored in the SD memory card, or send the corresponding signal to the Alarm Out terminal. RECOMMENDED PC SPECIFICATIONS y CPU : Pentium4 / 2.4GHz or higher y Operating System : Windows XP(Service Pack2, Service Pack3) / Windows Vista / Windows 7 y Resolution : 1024X768 pixels or higher y RAM : 512MB or higher y Web Browser : Internet Explorer 6.0 or higher y Video Card : Radeon, Nvidia y Video Memory : 128MB y DirectX 8.1 or higher Compatible IP Routers y Linksys y D-Link y Netgear Compatible PoE Switches y Linksys SRW224G4P y D-Link DES-1316 y SMC SMCPWR-INJ3 10_ overview WHAT’S INCLUDED Please check if your camera and accessories are all included in the product package. User Manual/ IP INSTALLER DVD Quick Guide Test Monitor Cable Screw Dust-proof Plate M The Test Monitor Cable is connected to a portable displayer and used for testing the camera. If you intend to use it for an actual monitoring camera, use the BNC cable instead. English _11 ● OVERVIEW Camera overview AT A GLANCE Appearance Item Description Dome Cover Case cover used to protect the lens and the main unit. b Main Unit Consists of: lens, switch board, PCB and screws. c Power Port Used to plug in the power cable. Video Output Port Used to connect the Video In connector of the monitor, from which the video signal of the camera outputs. Network Port Used to connect the PoE or LAN cable. M Wipe out a dirty surface of the lens softly with a lens tissue or cloth to which you have applied ethanol. 12_ overview Inside ● OVERVIEW Item Description Alarm In / Out terminals Alarm in/out terminals can be configured as follows: - ALARM IN : Terminal for Alarm Input. - ALARM OUT : Terminal for Alarm Output. - GND : Grounding terminal. b SD Memory Card Compartment Compartment for the SD memory card. c Reset Button Resets the camera settings. Press the button for about 3 seconds, and the system indicator turns off and will restart. J Resetting the camera r equires reconfiguration of network settings (IP address, subnet mask, gateway address etc.) using the IP Installer software application. English _13 overview Components 1 3 2 Lens 6 4 5 7 8 9 14_ overview Item b Description Cover used to protect the main unit. Wing-Side Hook Tap on either end to remove the inner cover. Monitor Out The Test Monitor Cable is connected to a portable displayer and used for testing the camera. Zoom Lever Used to adjust or fix the zoom factor of the lens. Focus Lever Turn it to the left or right to adjust the focus; turn it clockwise to fix the focus. Tilt Screw Used to adjust or fix the tilt of the lens. Bracket Used to install the camera on the wall or ceiling with the screws. Wiring Cover If you drill a hole in the wiring cover for wiring, remove the cover and attach the provided dustproof plate to it, and arrange the cables through the plate. The dust-proof plate is to prevent outside dust from inflow to the wiring compartment. Release Lock If you want to remove the bracket from the main unit or remove the camera from the bracket, push this out and turn the main unit in the <UNLOCK> direction. c English _15 ● OVERVIEW Inner Cover installation & connection REMOVING THE COVERS If you want to connect the Alarm I/O connectors, you must remove the dome cover and lens cover beforehand. 1. Turn the dome cover counter-clockwise. 2. Remove the dome cover by lifting it up. 3. Tap on either end of the lens cover to remove it. 16_ installation & connection INSERTING/REMOVING AN SD MEMORY CARD Inserting an SD Memory Card Push the SD memory card in the direction of the arrow shown in the diagram. Do not insert the SD memory card while it’s upside down by force. Otherwise, it may damage the SD memory card. Removing an SD Memory Card Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot. "-"3.065 "-"3.065 (/% "-"3.*/ "-"3.*/ J Pressing too hard on the SD memory card can cause the card to shoot out uncontrollably from the slot when released. Before ejecting the SD memory card, release the checkbox <SD Card Record> in <Alarm image> and press [Apply] button. (page 65) English _17 ● INSTALLATION & CONNECTION "-"3.065 "-"3.065 (/% "-"3.*/ "-"3.*/ J installation & connection MEMORY CARD INFORMATION (NOT INCLUDED) What is a memory card? The memory card is an external data storage device that has been developed to offer an entirely new way to record and share video, audio, and text data using digital devices. Selecting a memory card that’s suitable for you Your camera supports SDHC memory cards. You may, however, experience compatibility issues depending on the model and make of the memory card. Your camera supports SD memory cards. Note that supported memory card capacity is up to 2GB. For your camera, we recommend you use a memory card from the following manufacturers: SDHC/SD Memory Card: Panasonic, Sandisk, Toshiba Your camera supports 128MB to 16GB (SD Card : 2GB) of memory card capacity. Playback performance can be affected depending on the speed of memory card, so use the high-speed memory card. To ensure proper recording of video data, we recommend you use a memory card that supports at least read/write speed 10Mbps and Class 6. Memory Card Use SD and SDHC memory cards feature a switch that disables writing data on to the media. Having this switch to the Lock position will prevent accidental deletion of data stored in the memory card but at the same time will also prevent you from writing data on to the media. ❖ Memory Card Components Contacts Lock Switch SDHC 18_ installation & connection CONNECTING WITH OTHER DEVICE Monitor Network Power Supply Connect the power adaptor to the power input port. J Be careful not to reverse the polarity when you connect the power cable. You can also use a router featuring PoE (Power over Ethernet) to supply power to the camera. Connecting to the monitor Connect the [V_OUT] port of the camera to the video input port of the monitor. Network Connection Connect the Network cable to the local network or to the Internet. English _19 ● INSTALLATION & CONNECTION Power installation & connection Connecting to the I/O port box Connect the Alarm I/O cable to the corresponding port of the inner port box. ALARM IN GND ALARM OUT y ALARM IN 1, 2 : Used to connect the alarm input signal. y GND : Used for earth-grounding. y ALARM OUT 1, 2 : Used to connect the alarm output signal. Alarm I/O Wiring Diagram ALARM IN 1 1 ALARM IN 2 2 GND 3 External Relay ALARM OUT 1 4 External Relay ALARM OUT 2 5 20_ installation & connection INSTALLATION Precautions before installation Ensure you read the following instructions before installing the camera: Installing the camera 1. Hold down the bottom lock lever while removing the cover with the other hand. Removing the cover reveals the main unit and inner cover. 2. To fix the camera position, hold down either hook of the inner cover and lift it up. 3. Push the release lock out while turning the main unit in the <UNLOCK> direction to remove the bracket. If this doesn't work, use the hole on the bottom of the bracket to turn the bracket in the <LOCK> direction. English _21 ● INSTALLATION & CONNECTION y Select an installation site (ceiling or wall) that can endure at least 5 times of the camera weight. y Stuck-in or peeled-off cables can cause damage to the product or a fire. y For safety purposes, keep anyone else away from the installation site. And put aside personal belongings from the site, just in case. installation & connection 4. Use the provided screws (x3) to fix the bracket to a desired position (ceiling or wall). Ensure that the <CAMERA FRONT> label on the bracket faces the direction for camera monitoring. Wiring Cover 5. Arrange the cables through the bracket to the ceiling or wall. If you drill a hole in the ceiling cover for wiring, press hard to remove the cover and attach the dust-proof plate to it, and arrange the cables through the plate. If you intend to arrange the cables without drilling a hole, use the empty area opposite to the <CAMERA FRONT> label side for the wiring purpose. 6. Mount the main unit onto the bracket. Align the marking hole of the main unit with the <CAMERA FRONT> label of the bracket, and turn the unit in the <LOCK> direction. 7. Adjust the lens in a desired direction. For adjusting the lens direction, refer to "Adjusting the monitoring direction for the camera". 8. Secure the inner cover to the main unit. Fit the two holes of the wing-side locks on the inner cover into the corresponding hole of the main unit, and press it down until you hear a click. 9. Fix the cover to the main unit. Fit the protruding part inside the cover into the corresponding hole of the main unit, and turn the cover to fix it. 22_ installation & connection Adjusting the monitoring direction for the camera Panning Lens rotation You can adjust the camera direction only when the camera is fixed on the ceiling. Then, turning the camera to the left or right is referred to as "Panning", while tilting the angle is "Tilting". For panning, the panning limit is 220˚ for the clockwise, and 120˚ for the counterclockwise, a total of 340˚ enabled; further rotation is stopped by the stopper. Adjusting the zoom and focus Watch the camera’s real time video and rotate the “Zoom lever” to zoom in/out the subject as you want. Rotate the “Focus lever” until the image looks clear. For the position of the Zoom lever and Focus lever, refer to the “Components” (page 14). M It is recommended to install the camera 2.5M~10M high above from the floor. English _23 ● INSTALLATION & CONNECTION Tilt Adjustment Screw Tilting camera setup You can configure the camera settings using the Web Viewer. M For accessing the Web Viewer, refer to "Network Connection and Setup". (page 34) HOW TO USE THE KEYBOARD CONTROLLER Follow the steps below if you run the Web Viewer for setting the menus. 1. Launch the Web Viewer. 2. From the [Camera OSD] menu in the left pane, click [Menu]. The <MAIN MENU> screen appears. 3. Click the Up/Down (▲▼) buttons to move to a desired item. 4. Click the four direction (▲▼◄ ►) buttons to navigate through the menu items. 5. To change the value of a selected item, click the Left/Right (◄ ►) buttons. ]. 6. Click [ Your changes will be applied. : Exits the menu setup screen. Before exiting the setup screen, select [SAVE] to save your settings, or [QUIT] to cancel them. : Saves your settings and returns to the previous screen. : Use this icon if you want to save your settings after you specified the mask area and privacy area, etc. Once you saved your settings, the changes remain intact even if you select [QUIT] on exit. : Use this icon if you want to delete a mask, or privacy area, etc. Once you deleted your settings, the deletions remain valid even if you select [QUIT] on exit. : This arrow appears next to a menu that contains sub items. For the items with the "*" mark on the right, You can get help from "Terminology". (page 71) 24_ camera setup MAIN MENU You can configure the camera settings to your preference. ** MAIN MENU ** PROFILE CAMERA SET PRIVACY ZONE OTHER SET SYSTEM INFO PROFILE You can select one from the pre-determined modes as appropriate to your specific camera installation environment. Your selection on each item in PROFILE will affect all other settings of the camera. For the setting, refer to "PROFILE". (page 70) For selecting and saving each menu item, refer to "How to use the keyboard controller". (page 24) y STANDARD ◄ PROFILE ► Automatically optimizes the camera settings to *STANDARD the normal environment. ITS y ITS BACKLIGHT DAY/NIGHT This setting enables you to analyze the traffic GAMING situation and take the traffic information at a glance. BANK CUSTOM y BACKLIGHT This setting enables you to view a sharp background and object even in a severe backlight scene. y DAY/NIGHT Automatically optimizes the camera settings to the day and night scene. y GAMING This automatically configures the settings so that you can work in a stable illumination condition as indoors. y BANK Automatically optimizes the camera settings to the bank environment. y CUSTOM Your change to any of the PROFILE settings will switch the display to CUSTOM. English _25 ● CAMERA SETUP y PROFILE You can select a mode that is appropriate to the camera installation environment. y CAMERA SET Configure the camera functions and settings. y PRIVACY ZONE You can configure the privacy settings. y OTHER SET You can configure more settings including FACTORY DEFAULTS. y SYSTEM INFO Shows the camera version and type. camera setup CAMERA SETUP You can configure the general settings of the camera module. Use the four direction (▲▼◄ ►) buttons to select a desired item. CAMERA ID Provide the ID and position for a camera that displays on the screen. For selecting and saving each menu item, refer to "How to use the keyboard controller". (page 24) 1. Select <CAMERA SET> - <CAMERA ID>. 2. Use the four direction (▲▼◄ ►) buttons to select a desired character. In the lower input box of the screen, the selected character will be entered. You can enter up to 54 characters including alphabets, numbers and special characters. CAMERA ID ABCDEFGHIJKLMNOPQRSTUVWXYZO BCDEFGHIJKLMNOPQRSTUVWXYZO _ 123456789 : ? + *()/ SP►► ◄◄ SP►► ◄◄ SP LOCATION ------------------------------------------------- 3. When done, continue to select <LOCATION> to specify the display position of the camera ID. IRIS You can set the iris to control the intensity of radiation incoming to the camera. For selecting and saving each menu item, refer to "How to use the keyboard controller". (page 24) 1. Select <CAMERA SET> - <IRIS>. 2. Use the left/right (◄ ►) buttons to select <ALC>. y LEVEL : Select an overall brightness level. y BACKLIGHT : Select either <BLC> or <WDR>. - WDR : Specify the synthesis level in the WEIGHT, and shutter speed in the WDR LEVEL, or select <OUTDOOR> or <INDOOR> in the WHITE BAL. - BLC : Set the <BLC> area by specifying the <SIZE> and <POSITION>. M ALC LEVEL BACKLIGHT [ 00] ---- I ---OFF If the iris is set to <ALC>, fixing the iris is your priority when you adjust AE and the shutter speed. 26_ camera setup MOTION ◄ CAMERA SET CAMERA ID IRIS MOTION DNR SHUTTER SENS-UP FLICKERLESS XDR DIS ► ON ALC (F.FAST) (F.FAST)----MID OFF AUTO X4 OFF MID OFF DNR Reduces the noise on the screen. This is useful, especially for a noisy screen. Set it to <USER>, you can specify the level. SHUTTER The SHUTTER menu is used to set the fixed fast electronic shutter or auto fast electronic shutter. DAY/NIGHT WHITE BAL DIGITAL ZOOM DETAIL AGC COLOR SUP REVERSE POSI/NEGA PIP AUTO [2] OFF MID OFF + OFF SENS-UP If the brightness of the video signal is too low, the Slow Shutter function will be activated. Slow Shutter can collect the individual max frame rate to adjust the setting. FLICKERLESS If set to <ON>, the shutter speed will be fixed to 1/100 second. This will prevent possible screen distortion due to a mismatch between the vertical sync frequency and the blinking frequency of the lighting. If SHUTTER is set to AUTO, FIX, EXT mode / SENSE UP to FIX / AGC to FIX, the <DIS> menu will be disabled. XDR This will correct a brightness difference between different scenes for the optimal visibility. The higher the value is, the higher the correction level is. DIS Automatically compensates for the flicker on the screen. If set to <ON>, the image will be enlarged with digital zoom as much area as compensated. If you set DIS to ON, the compensation area will be enlarged as set in the digital zoom factor. If you set the digital zoom factor to greater than the enlarged zoom factor for the compensation, the DIS function will be deactivated. English _27 ● CAMERA SETUP You can specify a level of AGC for controlling the camera motion. Select F.FAST if you want to monitor a very fast moving object in a low contrast scene, and S.SLOW if monitoring a very slow moving, inanimate object in the same condition. As long as DAY/NIGHT is set to AUTO, the <MOTION> menu is not available. camera setup DAY/NIGHT You can specify a recording mode according to the scene. For selecting and saving each menu item, refer to "How to use the keyboard controller". (page 24) 1. Select <CAMERA SET> - <DAY/NIGHT>. 2. Select a screen transition mode according to the illumination, and set options as appropriate. y DAY : Fixed to DAY mode, regardless of the scene. y NIGHT : Fixed to NIGHT mode, regardless of the scene. If BURST is set to <ON>, the burst signal will output. y AUTO : According to the luminance, this will switch DAY to NIGHT mode, or vice versa. y DAYNIGHT / NIGHTDAY : If set to <AUTO>, you can specify the brightness level triggering the mode switch between DAY and NIGHT as well as the interval. y MASK AREA : If there exists a bright spot light source in a night scene, you can specify the size and position as needed. Any excessively bright area in a night scene will be masked. 28_ camera setup AUTO BURST DAY DAY NIGHT BRIGHTNESS DWELL TIME NIGHT NIGHT DAY BRIGHTNESS DWELL TIME MASK AREA MASK AREA <SIZE> <LOCATION> OFF MID 2S 1 MID 5S 2 WHITE BAL If you need to adjust the screen brightness, use the WHITE BALANCE function. For selecting and saving each menu item, refer to "How to use the keyboard controller". (page 24) 1. Select <CAMERA SET> - <WHITE BAL>. WHITE BAL DAY/NIGHT MODE RED BLUE DAY ATW2 [ 00] 00] ---- I ---[ 00 00]] ---- I ---- 3. According to the specified recording mode, WHITE BAL select a WHITE BAL mode with necessary options. DAY/NIGHT NIGHT BRIGHTNESS MID y BRIGHTNESS : Specify a brightness level MODE AWC [ 00 RED 00]] ---- I ---triggering the switch from DAY to NIGHT [ 00 BLUE 00]] ---- I ---mode. [[0040 R-GAIN 0040]] [[0133 B-GAIN 0133]] y MODE : According to the selected mode, you can adjust the RED and BLUE color level. - RED : Adjust the strength of the red color. - BLUE : Adjust the strength of the blue color. - R-GAIN/B-GAIN : Specify the current color temperature manually. You can set the R-GAIN, and B-GAIN value only in AWC mode. DIGITAL ZOOM You can set the digital zoom factor and position. When the zoom factor and position are defined, the digital zoom function will operate. If you set the digital zoom to a larger factor than the actual enlargement for compensation, the DIS function will be disabled. DETAIL You can adjust the vertical and horizontal sharpness, respectively. English _29 ● CAMERA SETUP 2. Select a mode where you set the balance. y DAY : You can set the RED, and BLUE value in DAY mode. y NIGHT : You can adjust the <WHITE BAL> according to the ambient luminance. camera setup AGC COLOR SUP This will adjust the color scheme according to the AGC value. REVERSE This will reverse the signal left to right, top to bottom, or a combination of the preceding. POSI/NEGA This will display the video brightness signal either normally or reversely. PIP You can view a main image with a sub image on the same screen. If more than one privacy zone is set and the PRIVACY SET is set to ON, the PIP function will be deactivated. 30_ camera setup PRIVACY ZONE You can set up to 12 privacy zones that will be hided for privacy of the subject when recording. For selecting and saving each menu item, refer to "How to use the keyboard controller". (page 24) ZONE SETUP 1. Select <MAIN MENU> - <PRIVACY ZONE>. 3. Select the <PIXEL LEVEL>. Specify the pixel unit level for the POSITION setting. 4. Select <POINT>. You will see dots on the screen. ◄ 1 7 PRIVACY ZONE 2 8 3 9 4 10 5 11 PRIVACY SET STYLE ► 6 12 ON MOSAIC1 PRIVACY ZONE SET 1 PIXEL LEVEL <POINT> <POSITION> [4] 5. Use the four direction (▲▼◄ ►) buttons to specify the position for each of the four dots. 6. Select <POSITION> and use the four direction (▲▼◄ ►) buttons to specify the position for each of the four dots. 7. Save the changes and move to the previous screen and select the <STYLE>. Select <COLOR> and pick a desired color. M Setting one or more privacy zone and enabling privacy function will disable the PIP function. English _31 ● CAMERA SETUP 2. Use the four direction (▲▼◄ ►) buttons to select a desired number. The Zone setup screen appears. camera setup OTHERS You can reset the camera, or select the OSD font color to your preference. For selecting and saving each menu item, refer to "How to use the keyboard controller". (page 24) LANGUAGE You can slect a preferred language for the screen display. Select your language by using the left and right keys. ◄ OTHER SET ► LANGUAGE ENGLISH FACTORY DEFAULTS OSD COLOR BW FACTORY DEFAULT 1. Select <MAIN MENU> - <OTHER SET> - <FACTORY DEFAULTS>. The FACTORY DEFAULTS setup screen appears. 2. Select <OK>. All the settings will be restored to the factory default. However, the language setting will not be restored. OSD COLOR You can set the font color of the user interface. 32_ camera setup FACTORY DEFAULTS OK CANCEL SYSTEM INFO You can check the system information. For selecting and saving each menu item, refer to "How to use the keyboard controller". (page 24) 1. Select <MAIN MENU> - <SYSTEM INFO>. 2. The current system information is displayed. SYSTEM INFO ► 3_IPV_N v2.00_101012 The camera type may different, depend on the video signal. English _33 ● CAMERA SETUP M ◄ TYPE CAMERA VER. network connection and setup You can set up the network settings according to your network configurations. M Before installing or while using this program, visit the Samsung website www.samsungsecurity.com and download and upgrade with the latest S/W version available. CONNECTING THE CAMERA TO AN IP ROUTER WITH THE XDSL/CABLE MODEM This is for a small network environment such as homes, SOHO and ordinary shops. SND-3080 INTERNET IP Router SND-3080 xDSL or Cable Modem xDSL or Cable Modem External Remote PC Local PC DDNS 서버 DDNS Server (Data Center, KOREA) (Data Center, KOREA) Configuring the network settings of the local PC connected to an IP router Configuring the network settings of the local PC connected to an IP router, follow the instructions below. y Select : <Network Neighborhood> <Properties> <Local Area Connection> <Properties> <General> <Internet Protocol (TCP/IP)> <Properties> <Obtain an IP address automatically> or <Use the following IP address>. y Follow the instructions below if you select <Use the following IP address>: ex1) If the address (LAN IP) of the IP router is 192.168.1.1 IP address: 192.168.1.100 Subnet Mask: 255.255.255.0 Default Gateway: 192.168.1.1 ex2) If the address (LAN IP) of the IP router is 192.168.0.1 IP address: 192.168.0.100 Subnet Mask: 255.255.255.0 Default Gateway: 192.168.0.1 34_ network connection and setup ex3) If the address (LAN IP) of the IP router is 192.168.xxx.1 IP address: 192.168.xxx.100 Subnet Mask: 255.255.255.0 Default Gateway: 192.168.xxx.1 M For the address of the IP router, refer to the product’s documentation. Checking if the IP router is connected to the xDSL/Cable modem properly y If it is properly connected, <IP Address>, <Subnet Mask> and <Gateway> provided by your ISP are displayed. Please remember these values because they are required so that an external remote computer of the IP router connects to the camera. However, note that certain ISPs change the settings of <IP Address>, <Subnet Mask> and <Gateway> on a regular basis y If the IP router is not properly connected, press the [Connect] button to try to reconnect or check if the settings of the IP router are correct. CONNECTING THE CAMERA TO AN IP ROUTER WITH LOCAL AREA NETWORKING This is for a large network environment such as corporate office, building, public office and factory. SND-3080 INTERNET SND-3080 공유기 IPIP Router 외부Remote 원격 PC PC External 방화벽 Firewall Local로컬 PCPC Local PC DDNSServer 서버 DDNS (Data Center, KOREA) (Data Center, KOREA) Configuring the network settings of the local PC connected to an IP router Configuring the network settings of the local PC connected to an IP router, follow the instructions below. y Select : <Network Neighborhood> <Properties> <Local Area Connection> <Properties> <General> <Internet Protocol (TCP/IP)> <Properties> <Obtain an IP address automatically> or <Use the following IP address>. English _35 ● NETWORK CONNECTION AND SETUP Select <Status> from the Settings menu of the IP Router network connection and setup y Follow the instructions below if you select <Use the following IP address>: ex1) If the address (LAN IP) of the IP router is 192.168.1.1 IP address: 192.168.1.100 Subnet Mask: 255.255.255.0 Default Gateway: 192.168.1.1 ex2) If the address (LAN IP) of the IP router is 192.168.0.1 IP address: 192.168.0.100 Subnet Mask: 255.255.255.0 Default Gateway: 192.168.0.1 ex3) If the address (LAN IP) of the IP router is 192.168.xxx.1 IP address: 192.168.xxx.100 Subnet Mask: 255.255.255.0 Default Gateway: 192.168.xxx.1 M For the address of the IP router, refer to the product’s documentation. CONNECTING THE CAMERA DIRECTLY TO A DHCPBASED XDSL/CABLE MODEM INTERNET SND-3080 xDSL xDSL또는 or Cable 모뎀 Cable Modem 외부 원격 PC PC External Remote DDNS Server 서버 DDNS (Data Center, KOREA) (Data Center, KOREA) Setting the IP Router This is enabled for a modem using DHCP. 1. Set the Static or Dynamic IP address. (pages 39~42) 2. Launch an Internet browser on the local PC connected to the IP Router. 3. Enter the IP Router’s address in the address bar of the browser. ex) http://192.168.1.1, http://192.168.0.1 or http://192.168.xxx.1 For the DDNS URL address, refer to "To check the DDNS address". (page 46) 36_ network connection and setup 4. When the IP Router is connected, the login window appears and prompts you to enter the password. For the login IP and the password, refer to the IP router’s documentation. 5. When done, you will see the setup window of the IP router. In the setup menu, select “Automatic Configuration-DHCP” for Internet Connection Type. For the menu location of Internet Connection Type or DHCP selection, refer to the IP router’s documentation. CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING Connecting to the camera from a local PC in the LAN 1. Launch an Internet browser on the local PC. 2. Enter the IP address of the camera in the address bar of the browser. SND-3080 INTERNET SND-3080 Firewall 방화벽 External Remote 외부 원격 PC PC 로컬 PC Local PC DDNS 서버 Server DDNS (DataCenter, Center, KOREA) (Data KOREA) M A remote PC in an external Internet out of the LAN network may not be able to connect to the camera installed in the intranet if the port-forwarding is not properly set or a firewall is set. In this case, to resolve the problem, contact your network administrator. English _37 ● NETWORK CONNECTION AND SETUP 6. When done, click the [Save] or [Apply] button to save the settings. network connection and setup BUTTONS USED IN IP INSTALLER Item Description Device Name Model name of the connected camera. Click the column to sort the list by model name. However, search will be stopped if clicked during the search. b Mode Displays either <Static> or <Dynamic> for the current network connection status. c MAC(Ethernet) Address Ethernet address for the connected camera. Click the column to sort the list by Ethernet address. However, search will be stopped if clicked during the search. IP Address IP address. Click the column to sort the list by IP address. However, search will be stopped if clicked during the search. The factory default is “192.168.1.200”. Protocol Network setting for the camera. The factory default is "IPv4". Cameras with the IPv6 setting will be displayed "IPv6". UPnP Status This function is not currently implemented. 38_ network connection and setup Item m URL DDNS URL address enabling access from the external Internet. However, this will be replaced with the <IP Address> of the camera if DDNS registration has failed. IPv4 Scans for cameras with the IPv4 setting. IPv6 Scans for cameras with the IPv6 setting. Search Scans for cameras that are currently connected to the network. However, this button will be grayed out if neither IPv4 nor IPv6 is checked. Auto Set <IP Installer> will automatically configure the network settings for you. Manual Set You should configure the network settings manually. Exit Exits the IP Installer program. STATIC IP SETUP Manual Network Setup Run <IP Installer.exe> to display the camera search list. At the initial startup, both [Auto Set] and [Manual Set] will be grayed out. M For cameras found with the IPv6 setting, these buttons will be grayed out as the cameras do not support this function. 1. Select a camera in the search list. Find the MAC (Ethernet) address labeled on the rear of the camera. Both the [Auto Set] and [Manual Set] buttons will be activated. 2. Click [Manual Set]. The Manual Setting dialog appears. The default values of <IP Address>, <Subnet Mask>, <Gateway>, and <HTTP Port> of the camera will be displayed. The default <PASSWORD> is 4321. 3. In the <ADDRESS> pane, provide the necessary information. y MAC (Ethernet) Address : The MAC (Ethernet) address of the applicable camera will be set automatically so you don't need to input it manually. English _39 ● NETWORK CONNECTION AND SETUP Description network connection and setup If using an IP router : y IP Address : Enter an address falling in the IP range provided by the IP router. ex) 192.168.1.2~254, 192.168.0.2~254, 192.168.XXX.2~254 y Subnet Mask : The <Subnet Mask> of the IP router will be the <Subnet Mask> of the camera. y Gateway : The <Local IP Address> of the IP router will be the <Gateway> of the camera. If not using an IP router : For setting <IP Address>, <Subnet Mask>, and <Gateway>, contact your network administrator. M The values of Device, TCP, UDP, Upload, and Multicast ports can not be changed manually, and will be adjusted according to the HTTP port value. 4. In the <Port> pane, provide necessary information. y HTTP Port : Used to access the camera using the Internet browser, defaulted to 80. Use the spin button to change the HTTP Port value. The start value of the port is 80, and increases or decreases by 6 like 10000, 10006, 10012. y VNP Port : Used to control the video signal transfer, defaulted to 60001(TCP). y TCP Port : Video signal transfer port using TCP protocols, defaulted to 60002(TCP). y UDP Port : Video signal transfer port using the UDP Unicast method, defaulted to 60003(UDP). y Upload Port : Used to upgrade the software firmware, defaulted to 60004(TCP). y Multicast Port : Video signal transfer port using the UDP Multicast method, defaulted to 60005(UDP). 5. Enter the password. This is the login password for the "admin" user who accesses the camera. The default password is "4321". 40_ network connection and setup 6. Click [OK]. Manual network setup will be completed. 7. When the manual setup including <IP> is completed, the camera will restart. If the IP router has more than one camera connected Configure the IP related settings and the Port related settings distinctly with each other. Category IP Address Subnet Mask Gateway HTTP Port VNP Port TCP Port Port related settings UDP Port Upload Port Multicast Port M Camera #2 192.168.1.200 255.255.255.0 192.168.1.1 192.168.1.201 255.255.255.0 192.168.1.1 80 60001 60002 60003 60004 60005 10000 10001 10002 10003 10004 10005 If the <HTTP Port> is set other than 80, you must provide the <Port> number in the address bar of the Internet browser before you can access the camera. ex) http://IP address : HTTP Port http://192.168.1.201:10000 Auto Network Setup Run <IP Installer.exe> to display the camera search list. At the initial startup, both [Auto Set] and [Manual Set] will be grayed out. M For cameras found with the IPv6 setting, these buttons will be grayed out as the cameras do not support this function. 1. Select a camera in the search list. Find the MAC (Ethernet) address labeled on the rear of the camera. Both the [Auto Set] and [Manual Set] buttons will be activated. 2. Click [Auto Set]. The Auto Setting dialog appears. The <IP Address>, <Subnet Mask>, and <Gateway> will be set automatically. English _41 ● NETWORK CONNECTION AND SETUP IP related settings Camera #1 network connection and setup 3. Enter the password. This is the login password for the "admin" user who accesses the camera. The default password is "4321". 4. Click [OK]. Auto network setup will be completed. 5. The camera will automatically complete the network setting and restart. DYNAMIC IP SETUP Dynamic IP Environment Setup y Example of the dynamic IP environment - If an IP router, with cameras connected, is assigned an IP address by the DHCP server - If connecting the camera directly to the xDSL or cable modem using the DHCP protocols - If IPs are assigned by the internal DHCP server via the LAN Checking the dynamic IP 1. From a local PC, run <IP Installer> to display a list of cameras that are assigned <Dynamic IP>. 2. Select a camera in the list, and click [Manual Set] to check the <Dynamic IP> of the camera. If you uncheck <DHCP>, you can change <IP> or <Port> to <STATIC>. 42_ network connection and setup PORT RANGE FORWARD (PORT MAPPING) SETUP If you have installed an IP router with a camera connected, you must set the port range forwarding on the IP router so that a remote PC can access the camera in it. Manual Port Range Forwarding ● NETWORK CONNECTION AND SETUP 1. From the Setup menu of the IP router, select <Applications & Gaming> <Port Range Forward>. For setting the port range forward for a third-party IP router, refer to the user guide of that IP router. 2. Select <TCP> and <UDP Port> for each connected camera to the IP router. Each port number for the IP router should match that specified in <Basic> - <IP> from the camera's Setup menu. 3. When done, click [Save Settings]. Your settings will be saved. English _43 network connection and setup CONNECTING TO THE CAMERA FROM A SHARED LOCAL PC 1. Launch <IP Installer>. It will scan for connected cameras and display a list of them. 2. Double-click a camera to access. The Internet browser starts and connects to the camera. M You can also access the camera in such way you type the IP address of the found camera in the address bar of the Internet browser. CONNECTING TO THE CAMERA FROM A REMOTE PC VIA THE INTERNET As a remote PC can not directly access <IP Installer>, you should access the camera in the IP router network using DDNS URL of the camera. 1. Before you can access a camera in the IP router network, you should have set the port range forward for the IP router. 2. From the remote PC, launch the Internet browser and type the DDNS URL address of the camera, or the IP address of the IP router in the address bar. ex) http://mfffe42.websamsung.net For the DDNS URL address, refer to "To check the DDNS address". (page 46) 44_ network connection and setup web viewer CONNECTING TO THE CAMERA Normally, you would ● WEB VIEWER 1. Launch the Internet browser. 2. Type the IP address of the camera in the address bar. ex) • IP address (IPv4) : 192.168.1.200 http://192.168.1.200 - the Login dialog should appear. • IP address (IPv6) : 2001:230:abcd: ffff:0000:0000:ffff:1111 http://[2001:230:abcd:ffff:0000 :0000:ffff:1111] If the HTTP port is other than 80 1. Launch the Internet browser. 2. Type the IP address and HTTP port number of the camera in the address bar. ex) IP address : 192.168.1.200:Port number(10000) http://192.168.1.200:10000 - the Login dialog should appear. Using URL 1. Launch the Internet browser. 2. Type the DDNS URL of the camera in the address bar. ex) URL address : http://mfffe42.websamsung.net - the Login dialog should appear. Connecting via URL (If the HTTP port is other than 80) 1. Launch the Internet browser. 2. Type the DDNS URL and HTTP port number of the camera in the address bar. ex) URL address : http://mfffe42.websamsung.net:Port number(10000) http://mfffe42.websamsung.net:10000 - the Login dialog should appear. English _45 web viewer To check the DDNS address The DDNS address consists of: <one of the lower-case letters: c, m, p> + <the last 6 digits of the MAC (Ethernet) address> + <websamsung.net> The small letter will be <c> if the first 6 digits of the MAC (Ethernet) address is <00:00:f0>, or <m> if they are <00:16:6c>, or <p> for <00:68:36>. ex) - If the MAC (Ethernet) address is 00:00:f0:ff:fe:42: c + fffe42 + websamsung.net = cfffe42.websamsung.net - If the MAC (Ethernet) address is 00:16:6c:ff:fe:42: m + fffe42 +websamsung.net = mfffe42.websamsung.net - If the MAC (Ethernet) address is 00:68:36:ff:fe:42: p + fffe42 +websamsung.net = pfffe42.websamsung.net J The above mentioned addresses are simply examples; do not use any of these for connecting purposes. LOGIN The default user ID is “admin”, and the default password is “4321”. 1. Enter “admin” in the <User Name> input box. 2. Enter “4321” in the <Password> input box. If the password is changed, enter the changed password instead. 3. Click [OK]. If you have logged in successfully, you will the Live Viewer screen. M For security purposes, ensure that you change the password in <Basic> - <User>. The administrator ID, “admin”, is fixed and can not be changed. If you check the “Save this password in your password list” option when your input is done, you will be logged in automatically without being prompted to enter the login information from next time on. J For this, your computer has installed DirectX 8.1 or later. You can get a free download of the latest DirectX from http://www.microsoft.com/download. If you are using Internet Explorer 7.0 or 8.0 as the default web browser, you can view the best quality image with a screen ratio of 100%. Reducing the ratio may cut the image on the borders. 46_ web viewer INSTALLING ACTIVEX If connecting to a camera for the first time, you will see the installation message. Then, install the required ActiveX to access the camera and control the video from it in real time. For Windows XP Service Pack 2 users ● WEB VIEWER 1. Click the installation message that pops up when you first access the camera. 2. Click <Install ActiveX Control...>. 3. The security warning popup appears, click [Install]. 4. When the required ActiveX is installed properly after your access to the camera, the Live screen should appear. J For normal installation, set the Block Popup setting as follows: Internet Explorer ➝ Tools ➝ Block Popup ➝ Always allow popups from the current site(A) English _47 web viewer USING THE LIVE SCREEN Item b c Description SD search Moves to the screen for searching event images from the SD card. Setup Move to the Setup screen. About You can check the firmware version, serial number and manufacturer information. Reset Alarm Resets the Alarm icon. (the Alarm and Motion icons disappear.) Capture Saves the snapshot as an image file in the .jpeg or .bmp format. Print Prints out the current image. Record Saves the snapshot as a video file in the .avi format. Full Screen Displays the Live screen in full screen. Video format You can set the video format (MJPEG, H.264/MPEG4) for vidoe files. The context menu will differ, depending on the codec specified in <Select H.264 & MPEG4 Video> of the active viewer. Alarm output On : Activates the specified Alarm Out port. Off : Deactivates the specified Alarm Out port. Pulse : Activates the Alarm Out port as much time as specified before deactivating it. 48_ web viewer Item Description Used to retrieve and customize the Camera Setup menu. Camera OSD For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 24) Viewer Screen Displays the Live video on the screen. ● WEB VIEWER BACKUP You can capture, print out, and save the snapshot in the specified path. To capture the snapshot 1. Click [ ] on the scene to capture. The Capture dialog should appear. 2. Click [OK]. The screenshot will be saved in the specified path. y Default file path - Windows XP : C:\Program Files\ Samsung\SND-3080\SnapShot\Live If you want to change the path, click [Set path ( )] and specify a path. - Windows Vista, Windows 7 : C:\users\[UserID]\Documents\Samsung\ SND-3080\SnapShot\Live On the Windows Vista, Windows 7 system, the path to save is fixed. y The screenshot file will be named automatically in the format of <IP address_ Port number_YYYYMMDD_hhmmss_index>. ex) 192.168.1.200_60001_20101012_204029_00 To print out the screenshot 1. Click [ ] on the scene to print out. The Print setup dialog appears. 2. Specify the name of the printer connected, and click [OK]. English _49 web viewer To record a video 1. Click [ ] on the scene to record. 2. You will see the Save AVI dialog; provide the necessary information. y Save path : You can change the default saving path. y File name : You can change the default file name. y HDD minimum free size : If the free space on the HDD is less than the recorded space, recording will be forcibly ended. 3. Click [OK]. Recording will start with the display of <REC> on the viewer screen. The video file will be saved into the specified path. 4. If you want to quit recording, click [ ] again. y Default file path - Windows XP : C:\Program Files\ Samsung\SND-3080\VideoClip\ Live If you want to change the path, click [Set path ( )] and specify a path. - Windows Vista, Windows 7 : C:\users\[UserID]\Documents\Samsung\ SND-3080\VideoClip\Live On the Windows Vista, Windows 7 system, the path to save is fixed. y The screenshot file will be named automatically in the format of <IP address_ Port number_YYYYMMDD_hhmmss_index>. ex) 192.168.1.200_60001_20101012_204059_00 y If you want to play an .avi file, you must have installed the corresponding DivX codec on your system. You can get a free download of the DivX from http://sourceforge.net/projects/ ffdshow/. y A specific codec to MPEG4 is required before you can play videos in the MPEG4 format. You can download the codec for MPEG4 videos from www.samsungsecurity.com. 50_ web viewer USING THE SD SEARCH VIEWER SCREEN 1. Click <SD search> tab in the Live screen. 2. The SD Search Screen appears. ● WEB VIEWER Name b c Function and description Thumbnail Size The thumbnail images are displayed based on the selected size. Date You can select the desired date to search for events generated. Schedule You can select the desired time to search the schedule events. Alarm input You can select the desired time to search the alarm events. English _51 setup screen ACCESSING THE SETUP SCREEN You can configure the default setting, system, overlay, event and network related settings, and change them as necessary. 1. In the Live screen, click the <Setup> tab. 2. The Setup screen appears. 52_ setup screen DEFAULT SETUP To configure the video settings You can set the video resolution and quality, and select the codec required. ● SETUP SCREEN 1. Select <Basic> - <Video>. The Video setup screen appears. y Brightness : Adjust the screen brightness from 1 to 100. y Contrast : Adjust the contrast from 1 to 100. y Resolution : Set the video size of the MPEG4, H.264, and MPEG files. - NTSC : 4CIF(704x480), VGA(640X480), CIF(352X240) - PAL : 4CIF(704x576), VGA(640X480), CIF(352X288) y Quality : Adjust the picture quality from 1 to 10. y Frame rate : - NTSC : Select one from 30 fps, 15 fps, 8 fps, 3 fps, and 1 fps. - PAL : Select one from 25 fps, 13fps, 6fps, 3fps and 1fps. y Bitrate control* : Select CBR (Constant Bit Rate) or VBR (Variable Bit Rate) for the compression method. If selecting VBR, you can not set the target bit rate. y y y y y y Target bitrate : Transfers video signal at a specified bit rate. Compression : Adjust the compression rate from 5 through 100 by 5. Encode priority : Set the video transfer method to Frame rate or Quality. GOP* size : Select a GOP size between 5 and 15. Deblock : This will soften the edges between macro blocks. De-interlace : You can set the grid noise reduction function. This can be set only if the resolution of MPEG4 video is 4CIF. English _53 setup screen y Profile : Select Baseline or Main for the H.264 profiling method. y Entropy coding* : Reduces the compression loss due to encoding. y Motion estimation : Estimates the movement of pixels by determining the motion vector. J If you set the profile to Baseline, the entropy coding is available only for CAVLC*; if you set it to MAIN, the entropy coding is available for both CAVLC* and CABAC*. If you set WDR to <OFF>, or the resolution of MPEG4 video is other than 4CIF, De-Interlace of MPEG4 codec will not be available. 2. When done, click [Apply]. Your settings will be saved. To configure the IP settings 1. Select <Basic> - <IP>. The IP setup window appears. y IP configuration : Set the IP and port settings for the camera. - IP type : Select one from <Static IP>, <Dynamic IP>, and <PPPoE IP>. If you select <PPPoE IP>, you can provide the optional ADSL IP and password. However, the multicast items (multicast address, port, TTL) for VNP and RTP will disappear. - MAC address : Displays the Ethernet MAC address. This is used for creating a DDNS address. - IP address : Displays the current IP address. - Subnet mask : Displays the <Subnet mask> for the set IP. - Gateway : Displays the <Gateway> for the set IP. - DNS server : Displays the DNS(Domain Name Service) server address. - HTTP webserver port : HTTP port used to access the camera via the web browser. The default is 80(TCP). - Upload port (TCP) : Used to upgrade the software firmware, defaulted to 60004(TCP). 54_ setup screen 2. When done, click [Apply]. Your settings are saved and the system restarts. The currently opened web browser will be closed. M If the IP router has more than one camera connected, you should configure IP and port settings differently with each other. English _55 ● SETUP SCREEN y IPv6 configuration : Obtains the IPv6 address to access the IPv6 network. y VNP configuration : Set a port used to transfer video signals with the Samsung protocols. - Device port (TCP) : Used to control the video signal transfer, defaulted to 60001(TCP). - TCP streaming port : Video signal transfer port using TCP protocols, defaulted to 60002(TCP). - UDP streaming port : UDP Port used to transfer video signal with the UDP Unicast protocols. The default is 60003(UDP). - Multicast address : IP address used to transfer video signal with the UDP Multicast protocols. The default is 225.128.1.128, and if you want to change the address, specify it ranging from 224.0.0.0 to 239.255.255.255. - Multicast port : UDP Port used to transfer video signal with the UDP Multicast protocols. The default is 60005(UDP). - TTL* : Set the TTL for the VNP packet. The default is 63, and if you want to change the address, specify it ranging from 0 to 255. y RTP configuration : You can set the RTP protocol. - RTSP port : You can set the RTSP port. - Streaming port : Used to transfer video signal with the RTP protocols. The default range is between 61000 and 61999. - Multicast address : IP address used to transfer video signal with the RTP protocols. - Multicast port : Used to transfer video signal with the RTP-protocol multicasting. - TTL* : You can set the TTL for the RTP packet. setup screen To set the user account 1. Click <Basic> - <User>. The User setup window appears. y Login authentication : You can set to authenticate the login by the user. - If you select <Enable>, the user should have gone through the login authentication; if selecting <Disable>, every user can access the system without the login authentication, having the ordinary user permissions. - When done, click [Apply]. y User login ID/password list : Displays a list of accessible users ID, passwords, and ratings. - You can add up to 10 users. - The admin ID is “admin”. - The password for the admin ID can be changed, but not added or deleted. 2. When done, click [Apply]. Your settings will be saved. The currently opened web browser will be closed. User Registration 1. From the User setup window, click [Insert]. The Register User window appears. 2. Provide the <User ID>, <Password>, and <Confirm password>, respectively. You can enter up to 9 alphanumeric or special characters (some excluded) for the user ID and password, respectively. 3. Select a user level. Select either <Operator> or <User> for a new user's permission. 4. Click [Apply]. The user registration is completed. J An existing user ID can not be added duplicate. Neither admin ID nor guest ID can be registered. 56_ setup screen To edit a registered user account 1. From the User setup window, select a user ID to change. 2. From the User setup window, click [Modify]. The Modify user window appears. ● SETUP SCREEN 3. Change the <User ID>, <Password>, <Confirm password>, and <Level> as you wish. 4. Click [Apply]. The selected user ID will be changed. To delete a user ID 1. From the User setup window, select a user ID to delete. 2. From the User setup window, click [Delete]. The selected user ID will be deleted. M About the user permission Administrator : Can use all functions (change/control settings). Operator : Can use only the functions available in the Live Viewer. User : Can only view the video on the Live Viewer. To set the display language 1. Click <Basic> - <Language>. The Language setup window appears. You can select one from 7 languages (English/Korean/Chinese/French/Italian/ Spanish/German). 2. When done, click [Apply]. The selected language will be applied. English _57 setup screen SYSTEM SETUP To set the date/time You can obtain the current system time from the NTP server or your PC for your time setting. 1. Select <System> - <Date & Time>. The Date & Time setup window appears. 2. If you select Manual, input the date and time manually. Your settings will be saved. y Current system time : The specified time in System Time Setup will be applied. y System time setup : You can synchronize the system time with the NTP server (time server) or your PC, or specify it manually. M You can specify the time between January 1, 2000 and December 31, 2037. To set the system time 1. Select a desired address in <Address> or select <Synchronize with PC viewer>. 2. If you select Manual, input the date and time manually. 3. Click [Apply]. The specified system time will be applied. M <NTP Server IP> is provided by a public agency, the list of which is subject to change from time to time. In a local network, a separate NTP server must be manually defined. J The current time can vary depending on the computers regional (GMT and DST) and country (PC time configuration) settings. 58_ setup screen To check the log information Select <System> - <Log>. The Log information list appears. M ● SETUP SCREEN y System log list : Shows the log information about the system changes along with time and IP address. - User login : Shows the current login user to the camera. - Video configuration change : Show video setting changes. - System time change : Shows the time changes. - System started : Shows time when the camera is turned on. The maximum of 2000 logs can be recorded. If the log number is over 2000, the log in the bottom of the log list will be replaced with a new log. To update the software Select <System> - <Software update>. The Software update window appears. How to update the software 1. From the software update window, click [Browse…]. The Open dialog appears. 2. Select an updatable file and click [Open]. 3. From the software update window, click [Install]. The selected file will be unzipped with a start of the update. It may take a several minutes to complete the update. 4. When the software update is completed, you will be prompted to restart the system. 5. Click [OK] to restart the system. Since the current connection is disconnected, you have to connect to the system again. English _59 setup screen J If the network is disconnected, the power supply fails, or the PC abnormally operates during the update, the system does not work at all. To reset the system Restart or reset the system if it does not work properly or causes a problem. Select <System> - <Reset>. The Reset window appears. y Restart : Restarts the system. y Factory default : Resets the system settings to the factory defaults with following two options: - Except network parameter : Resets all settings except for the Network Parameters. - All : Restores all settings to the default. This works the same as pressing the [RESET] button on the inside of the camera. J After the system is reset or restarts, you should try to connect to the camera again. It takes several minutes until the system completes rebooting. Wait until the system rebooting is completed and try to connect again. After executing <Factory default>, you must run the <IP Installer.exe> program to change the basic network settings such as IP address, Subnet mask, Gateway, etc., before you can connect to the Internet. To set the HTTPS 1. Select <System> - <HTTPS>. The HTTPS setup window appears. y Secure connection system : Select a secure connection system to use. To use the secure connection mode requiring the public certificate for the secure connection system, you must have installed a signed certificate issued by a certificate authority on your system. 60_ setup screen y Install a public certificate : To install the certificate to camera, you need to type a certificate name (it can be arbitrarily assigned by user), certificate file issued from the authority and a key file. When done, click [Install]. If the certificate is installed successfully, the user-defined certificate name will be displayed. Also, the option button of <HTTPS (Secure connection mode using the public certificate)> in the upper side becomes activated. To access the camera using HTTPS mode, you have to type the IP address for the camera in the form of “https://<Camera_IP>”. ● SETUP SCREEN M 2. When done, click [Apply]. The web viewer will switch to the set secure connection system. OVERLAY SETUP You can display text on the screen. To set the text 1. Select <Overlay> - <Overlay text>. The Overlay Text setup window appears. 2. When done, click [Apply]. Your settings will be saved. y Overlay text settings : If you select <Disable>, the overlay text will not be displayed; If selecting <Enable>, it will display on the screen. y Show date : Set to display the date information on the bottom screen. - Output Format : Select a display format of the date information. YYYY-MM-DD : Year-Month-Day / MM-DD-YYYY : Month-Day-Year/ DD-MM-YYYY : Day-Month-Year y Show time : Set to display the time information on the bottom screen. - Output Format : Select a display format of the time information. 24hr : Displays the time in the 24-hour format. 12hr : Displays the time in the 12-hour format. y Text color : Select black or white for the text color. y Background color : Select black or white for the background color. English _61 setup screen EVENT SETUP To set the event transfer function You can set the FTP/email server (SMTP) to transfer the alarm images present in the camera, in case an alarm event occurs. Select <Event> - <Transfer setup>. The Image transfer setup window appears. M For more information on commercial SMTP services, contact the SMTP service provider. To test the FTP transfer Click [Test]. This will test if the image is transferred to the specified FTP server properly. When the test on the FTP server connection and transfer is done, a message of <( Verified )> will be displayed. You will see an error message if the test fails. If this is the case, check the FTP server status or the settings again. y FTP transfer : With this, you can transfer alarm images to the FTP server. If the initial FTP server setting and the connection status are not verified, the <( Not verified )> message appears. - Use passive mode : Select this option when the passive mode connection is inevitable due to the firewall or FTP server setting. - FTP server address : Enter the IP address of a FTP server to which an alarm image will be transferred. 62_ setup screen English _63 ● SETUP SCREEN - Upload path : You can specify the path of the FTP directory to which you will transfer an alarm image. You can specify the path by just typing </directory name> or <directory name> in this field. If nothing is specified, the path will be defaulted to the root directory of the FTP server. - Port : The FTP port is defaulted to 21. This value can be changed according to the FTP server setting. - User ID : Provide the user account ID to access the FTP server. - Password : Provide the user account password to access the FTP server. y E-mail(SMTP) transfer : With this setting, you can transfer alarm images to the email server. This function is available only for the SMTP email server. When the initial SMTP server setting and connection are not verified, the <Not verified> message appears. - SMTP server address : Enter the SMTP server address to use when you send an email. ex) 10.240.56.228 - Port : Enter a port number to use when you send an email. The default is 25. - User ID : Provide the user account ID to access the SMTP server. - Password : Provide the user account password to access the SMTP server. - E-mail sender : Enter the address of the email sender. If the sender address is incorrect, the email from the sender may be classified as SPAM by the SMTP server and may not be sent. - E-mail receiver : Enter the addressz of the email receiver. - Title : Enter the subject of the email to send. - Message : Enter the content of the email to send. setup screen To test the email transfer Click [Test]. This will test if the image is transferred to the specified SMTP server properly. When the test on the SMTP server connection and transfer is done, a message of <( Verified )> will be displayed. You will see an error message if the test fails. If this is the case, check the SMTP server status or the settings again. To setup the record 1. Click <Event> - <Record setup>. The Record setup window appears. 2. To complete the setting, click the [Apply] button. The settings are saved. y SD card : Enables you to verify data saved on the SD memory card and format the memory card itself. It is possible to set to automatically delete movie clips recorded before a certain period of time (e.g. 1 week, 1 month, or 1 year). y Options : Determine whether or not you wish to receive Email notification of insufficient capacity warnings. 64_ setup screen To set an alarm image You can configure to send message via FTP/E-mail (SMTP) or to save recording into the SD memory card. Select a transfer method when an event occurs or the schedule transfer function is activated. ● SETUP SCREEN 1. Select <Event> - <Alarm image>. The Alarm Image setup window appears. y Transfer mode : You can select alarm message notification method among FTP/E-mail transfer and SD Card recording. - FTP transfer : The image is sent to the specified FTP address. - E-mail transfer : The image is sent to the specified email address. - SD Card Record : Saves images into the SD memory card. M If an SD memory card is not inserted, the corresponding button will be disabled. In this case, insert the SD memory card into the slot and refresh to enable the button. J If the SD memory card is ejected while the button is checked, the camera automatically restarts. y Transferred image naming setup : You can set the file name of an alarm image to be sent when an alarm is triggered or during the scheduled transfer. y Pre/post alarm image : You can set to save the pre or post alarm image. - Number of image : The frame rate per second can be one among 1, 2, 3, and 5. - Pre-alarm duration : The pre alarm duration can be one among 5 seconds, 10 seconds, 15 seconds, and 30 seconds. You can send a pre-alarm image of up to 30 seconds before the alarm is triggered. (The max time differs, depending on the frame rate) - Post-alarm duration : The post alarm duration can be one among 5 seconds, 10 seconds, 15 seconds, and 30 seconds. You can send a post-alarm image of up to 30 seconds after the alarm is triggered. (The max time differs, depending on the frame rate) M The pre/post alarm duration is not available in SMTP transfer mode. Only one image at the corresponding time will be transferred. 2. When done, click [Apply]. Your settings will be saved. English _65 setup screen To set the alarm input 1. Select <Event> - <Alarm input 1> or <Alarm input 2>. The Alarm Input setup window appears. 2. When done, click [Apply]. Your settings will be saved. y Input device setup : Select an input type according to the characteristics of the alarm sensor on the rear of the camera. - Off : Turns off the alarm input setting. - NO (Normal Open) : It is normally open, but if it is closed, an alarm will be triggered. - NC (Normal Close) : It is normally closed, but if it is open, an alarm will be triggered. y Activation time : You can set a time to execute a specific command when an alarm occurs. - Always : Always executes the specified command when an alarm occurs. - Only scheduled time : Executes the specified command when an alarm occurs only on a specified weekday, or time. y Action : You can set an action to execute when an alarm occurs. - Alarm output : Set the alarm output port to which the alarm signal is transferred. - Output duration : Set the period of time to output the alarm signal to the specified alarm output port when an alarm occurs. If a new alarm event is detected during the alarm output, the delay time is recalculated based on the detection time of the recent alarm. - Alarm image transfer : If you select <On>, you can transfer JPEG images to a registered address via FTP or SMTP server or save images into the SD memory card according to the setting in <Event> - <Transfer setup>. 66_ setup screen To set the motion detection function 1. Select <Event> - <Motion>. The Motion Detection setup window appears. English _67 ● SETUP SCREEN 2. When done, click [Apply]. Your settings will be saved. y M.D. function : If selecting <Enable>, the motion detection function will be activated; if selecting <Disable>, it will not operate at all. y M.D. configuration : Configure the motion detection settings. - Motion sensitivity : Select one from <High>, <Medium> and <Low>. Selecting <High> will trigger the motion detection event even with a small motion. - Motion area : Set an area where the motion detection is performed. y Activation time : Set the time to activate a specified operation when a motion is detected. - Always : Always executes the specified command when a motion is detected. - Only scheduled time : Executes the specified command when a motion is detected only on a specified weekday, or time. y Action : You can set an action to execute when a motion is detected. - Alarm output : Set the alarm output port to which the motion detection signal is transferred. - Output duration : Set the period of time to output the motion detection signal to the specified alarm output port when a motion is detected. If another motion is detected during the alarm output, the delay time is recalculated based on the detection time of the recent motion. - Alarm image transfer : If you select <On>, you can transfer JPEG images to a registered address via FTP or SMTP server or save images into the SD memory card according to the setting in <Event> - <Transfer setup>. setup screen To set a motion area You can set a specific area to detect a motion in. 1. From the Motion Detection setup window, click [Setup] in the <Motion area>. The Motion Area window appears. You can set a specific area to detect a motion in. 2. Click over square boxes corresponding to the target motion area. The selected area will be highlighted yellow. 3. To cancel the selection, click the square box again. The square box will restore its original color. 4. When done, click [Apply]. Your settings will be saved. The Motion Detection function will operate on the selected area. To set the scheduled transfer You can set to transfer the JPEG image to the FTP/SMTP server saved in the SD memory card at a specific interval. 1. Select <Event> - <Schedule>. The Schedule Transfer setup window appears. y Schedule transfer function : If selecting <Enable>, the schedule transfer function will be activated; if selecting <Disable>, it will be deactivated. y Transfer interval : You can set the time interval to transfer images. You can set the unit of the interval to <seconds> or <minutes>; you can also set to transfer one image per 5/15/30/45/60 seconds, or one per 5/15/30/45/60 minutes. y Activation time : You can set a time to execute a specific command when a schedule transfer event occurs. - Always : Always sends an image at the set interval. - Only scheduled time : Sends the image only on a specified weekday, or time. 2. When done, click [Apply]. Your settings will be saved. 68_ setup screen NETWORK SETUP To set the video transfer mode You can control the transfer rate according to the video transfer mode and network speed. 2. When done, click [Apply]. Your settings will be saved. y VNP streaming : You can set the Samsung Protocol (VNP) for the streaming service. - Protocol : Select a video transfer protocol from TCP*, UDP (Unicast)*, and UDP (Multicast)*. Multicast backbone (MBone) is not supported; you can access the camera only in the multicast local network environment. y RTP streaming : You can set the RTP Protocol or the streaming service. - Protocol : Select a video transfer protocol from UDP (Unicast) and UDP (Multicast). To set the DDNS DDNS is an abbreviation of Dynamic Domain Name Service that converts the IP address of a camera into a general Host Name so that the user can easily remember it and enables connecting a camera with a fixed Host Name even if the IP address of the camera may be dynamically changed. 1. Select <Network> - <DDNS>. The DDNS setup window appears. 2. When done, click [Apply]. Your settings will be saved. M For checking the DDNS address, refer to “To check the DDNS address”. (page 46) English _69 ● SETUP SCREEN 1. Select <Network> - <Streaming type>. The Video Transfer setup window appears. appendix PROFILE CAMERA SETUP MENU STANDARD ITS BACKLIGHT DAY/NIGHT ALC ALC ALC - - - DC DC DC GAMING BANK ALC ALC ALC - - - DC DC DC Parent Menu Sub-menus ALC IRIS LENS LEVEL BACKLIGHT MOTION 0 0 0 0 0 0 OFF OFF WDR OFF OFF WDR (F.FAST) --- (F.FAST) --- NORM (F.FAST) --- SLOW (F.FAST) --- DNR MID MID MID MID MID MID SHUTTER OFF AUTO 1/250 OFF OFF OFF OFF SENSE UP AUTO X4 AUTO X2 AUTO X4 AUTO X4 AUTO X4 AUTO X4 XDR MID MID MID MID MID MID AUTO AUTO DAY AUTO DAY AUTO DAY/NIGHT NIGHT - - - - - - OFF ON OFF OFF OFF OFF DAY DAY/NIGHT DAY DAY/NIGHT DAY DAY - - - - - - MODE ATW2 ATW1 ATW1 ATW1 ATW1 ATW2 RED 0 0 0 0 0 0 BLUE 0 0 0 0 0 0 - - - - - - MID Custom Setting MID ATW2 OFF ATW2 0 Custom Setting 0 Custom Setting Custom Setting 0 Custom Setting 0 Custom Setting Custom Setting 2 2 2 BURST DAY WHITE BAL NIGHT BRIGHTNESS Custom Setting MODE OFF RED Custom Setting BLUE Custom Setting DETAIL 70_ appendix 2 Custom Setting Custom Setting OFF 2 OFF 2 TERMINOLOGY y Entropy coding : Data transfer technology used to reduce the compression loss from encoding. - CAVLC (Context-adaptive variable-length coding): Records a higher compression loss rate than CABAC. - CABAC (Context-adaptive binary arithmetic coding): Shows a lesser compression loss than CAVLC. y Bitrate Control - CBR(Constant Bitrate) This will transfer video data in an equal size at all times, regardless of the video complexity. The video quality may be deteriorated, depending on the video complexity. - VBR(Variable Bitrate) The amount of video data to transfer may differ, depending on the video complexity. This enables receiving video data in an equal quality at all times. y TTL : TTL stands for “Time To Live”, which you can specify to prevent loss of data packet that passes through multiple-staged routers. Each router decreases the TTL value by one each time a packet passes it through; If the TTL value reaches 0, the packet cannot further pass through a router. y TCP : It is a general purpose protocol used for transmission that requires reliability. With constant communication between the sender and recipient, it provides high reliability against transmission data loss; however, it has imitation to transmit a large amount of data in real time at a high speed. It enables reliable data transmission over xDSL and cable network at a relatively slow speed. y UDP (Unicast): It refers to a system that transmits data between only one transmitter and one receiver (1:1). y UDP (Multicast): It refers to the data transfer protocol in one-to-many (1:N) between the transmitting and receiving terminals; although it alleviates the network load, it requires <Multicast> router. For more information such as whether the network over which the camera is installed supports <Multicast>, contact the network administrator. y UDP : It is a protocol appropriate to transmit a large amount of data such as multimedia data at a high speed. However, with its nonconnection structure, it records a higher transmission efficiency than TCP especially in a high LAN environment faster than 100Mbps. English _71 ● APPENDIX y GOP : The default is 15, and if set to 15, one I-Frame will be output per 15 frames as one I-Frame and 14 P-Frames constitute the GOP. The lower the GOP size is, the better the quality is; however, the bit rate as well as the data size will increase, causing a lower of the fps. GOP(Group of Pictures) is a set of video frames for MPEG4 and H.264 format compression, indicating a collection of frames from the initial I-Frame (key frame) to the next I-Frame. GOP consists of 2 kinds of frames: I-Frame and P-Frame. I-Frame is the basic frame for the compression, also known as Key Frame, which contains one complete image data. P-Frame contains only the data that has changed from the preceding I-Frame. appendix SPECIFICATIONS Description Item Camera Type NTSC Color/BW Color Device Image Scanning Pixels Total Effective System Horizontal Frequency Vertical Frequency 1/3" Super-HAD PS CCD 811 x 508 768 x 494 Progressive 15.734 Hz 59.94 Hz 795 x 596 752 x 582 15.625 Hz 50 Hz Color Sens off : 0.12 Lux(15 IRE), 0.2 Lux(30 IRE), 0.4Lux(50 IRE)@F1.2 Sens up x512 : 0.00023 Lux(15 IRE), 0.0005 Lux(30 IRE), 0.0008 Lux(50 IRE)@F1.2 B/W Sens off : 0.012 Lux(15 IRE), 0.02 Lux(30 IRE), 0.04Lux(50 IRE)@F1.2 Sens up x512 : 0.000023 Lux(15 IRE), 0.00005 Lux(30 IRE), 0.00008 Lux(50 IRE)@F1.2 Number of Privacy Zone Day/Night Extended Dynamic Range WDR D-Zoom PIP High Speed Shutter Flickerless Sens Up BLC AGC Camera ID White Balance Digital Noise Reduction Digital Image Stablization Etc. Function 12 ea Day/Night/AUTO(Soft Method) Off/On (Level Setting) Off/On (128) Off/On (160) x1 ~ x16 (x0.1 STEP) Off/On (Advanced) 1/60 ~ 1/10Ksec 1/50 ~ 1/10Ksec Off/On x2 ~ x512 Off/On (Area Setting) Off/On (Max.Level Setting) Off/On (Max.54ea/2Line) ATW1/ATW2/AWC/MANUAL Off/On (Adaptive 3D+2D) Off/On Detail, Reverse(H/V), Posi/Nega Min. Scene Illumination Functions PAL 72_ appendix Description Item NTSC Horizontal 600 TV Lines Vertical 350 TV Lines PAL Resolution Video Output Video Output S/N Ratio VBS 1.0Vp-p about 52 dB Lens Drive Type AI (DC) ● APPENDIX S/N Ratio Lens Network Board Mount Type Board Type OS Embedded Linux Hardware Flash memory 32M byte RAM 256M byte DSP TI Davinci Ethernet RJ-45 (10/100BASE-T) PoE Yes (IEEE802.3af) Input 2 ea Output 2 ea Compression H.264 / MPEG4 / MJPEG Multiple Codec (H.264 / MPEG4 selectable) Simultaneous Dual Streaming Alarm Video Resolution 4CIF 704x480 VGA 640x480 CIF 704x576 352x240 352x288 Frame Rate 30, 15, 8, 3, 1 fps 25, 13, 6, 3, 1 fps Quality 1 ~ 10 level OSD Camera Control and Adjustment OSD menu on Video (Menu enter/exit, move by Web UI) * Some key adjustment menus will be supported by CGI API. Motion Detection Sensitivity and Area Setting High, Medium, Low English _73 appendix Description Item NTSC IP Network Protocol Protocol IPv4 TCP/IP, UDP/IP, RTP(UDP), RTP(TCP), RTSP, NTP, HTTP, HTTPS, SSL, DHCP PPPoE, FTP, SMTP, ICMP, IGMP, SNMPv1/v2c/v3(MIB-2), ARP, DNS, DDNS, VSIP IPv6 TCP/IP, HTTP, HTTPS, SSL, DHCP Streaming Unicast (TCP, UDP), Multicast (UDP) Security HTTPS Login Authentication Digest Login Authentication DDNS Supporting Samsung DDNS and Public DDNS services Maximum User Access Connection Administrator User Access Level Live Monitoring, Alarm I/O control User Live Monitoring Alarm Input Video Player JPEG Image transfer : FTP, SMTP, SD Card Notification : notify to viewer or by E-mail (one image attachment) Alarm Out Schedule JPEG Image transfer : FTP, SMTP, SD Card Supported OS Windows XP, Windows VISTA, Windows 7 Supported Browser Internet Explorer 6.0 or Higher UI Language E/F/G/S/I/C/K S/W upgrade Support RTP/RTSP streaming Quicktime, VLC player Video Management Software Application Max 10 Users at Unicast (TCP, UDP) Mode Max 20 Users at Multicast (UDP) Mode Live Monitoring, Alarm I/O control, OSD menu control, SETUP Operator Event Management Motion Detection Web Browser Viewer (Default) PAL IPv4 / IPv6 Samsung iPOLiS 3rd Party S/W appliction IP Installation 74_ appendix IP Installer Application for All Samsung IP Devices Item HTTP API CGI Command SDK RTP/RTSP API RTP Header, RTSP Command Document SDK ActiveX API for viewing data streams from IP camera. Power AC24V±10%(60Hz±0.3Hz)/ DC12V+10%/-5% / PoE (Power over Ethernet) Power Consumption Max. 8W Operating Temp. -10˚C~50˚C Operating Humidity ~90% Dimension (Ø x H) 133.0(Ø) x 129.4(H)mm Weight About 523g English _75 ● APPENDIX ActiveX Description NTSC PAL Provides functionality to control cameras and set/retrieve internal parameter values. Get JPEG image or MJPEG stream Alarm In/Out control appendix FRAME RATE (NTSC) Test Condition: MJPEG - Resolution(CIF), Quality(1), Frame rate(1) M H.264 - Bitrate control(CBR), Compression(40), Encode Priority(Frame rate), GOP size(15), Deblock(ON), Profile(Baseline), Entropy coding(CAVLC), Motion estimation(HPel) MPEG4 - Bitrate control(CBR), Compression(40), Encode Priority(Frame rate), De-Interlace(ON), GOP size(15) ❖ MPEG4 (4CIF) Frame Rate 30 FPS 15 FPS 8 FPS 3 FPS 1 FPS LEVEL10 4239 Kbps 23 FPS 2765 Kbps 15 FPS 1290 Kbps 7 FPS 737 Kbps 4 FPS 221 Kbps 1 FPS LEVEL9 3686 Kbps 24 FPS 2304 Kbps 15 FPS 1075 Kbps 7 FPS 614 Kbps 4 FPS 184 Kbps 1 FPS LEVEL8 3072 Kbps 25 FPS 1843 Kbps 15 FPS 860 Kbps 7 FPS 492 Kbps 4 FPS 147 Kbps 1 FPS LEVEL7 2396 Kbps 26 FPS 1382 Kbps 15 FPS 645 Kbps 7 FPS 369 Kbps 4 FPS 111 Kbps 1 FPS LEVEL6 1659 Kbps 27 FPS 922 Kbps 15 FPS 430 Kbps 7 FPS 246 Kbps 4 FPS 74 Kbps 1 FPS LEVEL5 1336 Kbps 29 FPS 691 Kbps 15 FPS 323 Kbps 7 FPS 184 Kbps 4 FPS 55 Kbps 1 FPS LEVEL4 1133 Kbps 30 FPS 576 Kbps 15 FPS 269 Kbps 7 FPS 154 Kbps 4 FPS 46 Kbps 1 FPS LEVEL3 922 Kbps 30 FPS 461 Kbps 15 FPS 215 Kbps 7 FPS 123 Kbps 4 FPS 37 Kbps 1 FPS LEVEL2 691 Kbps 30 FPS 346 Kbps 15 FPS 161 Kbps 7 FPS 92 Kbps 4 FPS 28 Kbps 1 FPS LEVEL1 461 Kbps 30 FPS 230 Kbps 15 FPS 108 Kbps 7 FPS 61 Kbps 4 FPS 18 Kbps 1 FPS Quality 76_ appendix ❖ H.264 (4CIF) Frame Rate 15 FPS 8 FPS 3 FPS 1 FPS LEVEL10 1229 Kbps 10 FPS 737 Kbps 6 FPS 369 Kbps 3 FPS 147 Kbps 1 FPS LEVEL9 1751 Kbps 19 FPS 1198 Kbps 13 FPS 645 Kbps 7 FPS 369 Kbps 4 FPS 111 Kbps 1 FPS LEVEL8 1536 Kbps 20 FPS 1075 Kbps 14 FPS 538 Kbps 7 FPS 307 Kbps 4 FPS 92 Kbps 1 FPS LEVEL7 1352 Kbps 22 FPS 897 Kbps 15 FPS 430 Kbps 7 FPS 246 Kbps 4 FPS 74 Kbps 1 FPS LEVEL6 1129 Kbps 25 FPS 691 Kbps 15 FPS 369 Kbps 8 FPS 184 Kbps 4 FPS 55 Kbps 1 FPS LEVEL5 960 Kbps 25 FPS 576 Kbps 15 FPS 307 Kbps 8 FPS 154 Kbps 4 FPS 46 Kbps 1 FPS LEVEL4 799 Kbps 26 FPS 461 Kbps 15 FPS 246 Kbps 8 FPS 123 Kbps 4 FPS 37 Kbps 1 FPS LEVEL3 622 Kbps 27 FPS 346 Kbps 15 FPS 184 Kbps 8 FPS 92 Kbps 4 FPS 28 Kbps 1 FPS LEVEL2 445 Kbps 29 FPS 230 Kbps 15 FPS 123 Kbps 8 FPS 61 Kbps 4 FPS 18 Kbps 1 FPS LEVEL1 223 Kbps 29 FPS 115 Kbps 15 FPS 61 Kbps 8 FPS 31 Kbps 4 FPS 9 Kbps 1 FPS English _77 ● APPENDIX 30 FPS 2298 Kbps 19 FPS Quality appendix ❖ MPEG4 (VGA) Frame Rate 30 FPS 15 FPS 8 FPS 3 FPS 1 FPS LEVEL10 4055 Kbps 22 FPS 2580 Kbps 14 FPS 1290 Kbps 7 FPS 737 Kbps 4 FPS 221 Kbps 1 FPS LEVEL9 3533 Kbps 23 FPS 2304 Kbps 15 FPS 1075 Kbps 7 FPS 614 Kbps 4 FPS 184 Kbps 1 FPS LEVEL8 2949 Kbps 24 FPS 1843 Kbps 15 FPS 860 Kbps 7 FPS 492 Kbps 4 FPS 147 Kbps 1 FPS LEVEL7 2304 Kbps 25 FPS 1382 Kbps 15 FPS 645 Kbps 7 FPS 369 Kbps 4 FPS 111 Kbps 1 FPS LEVEL6 1536 Kbps 25 FPS 922 Kbps 15 FPS 430 Kbps 7 FPS 246 Kbps 4 FPS 74 Kbps 1 FPS LEVEL5 1152 Kbps 25 FPS 691 Kbps 15 FPS 323 Kbps 7 FPS 184 Kbps 4 FPS 55 Kbps 1 FPS LEVEL4 998 Kbps 26 FPS 576 Kbps 15 FPS 269 Kbps 7 FPS 154 Kbps 4 FPS 46 Kbps 1 FPS LEVEL3 799 Kbps 26 FPS 461 Kbps 15 FPS 246 Kbps 8 FPS 123 Kbps 4 FPS 37 Kbps 1 FPS LEVEL2 622 Kbps 27 FPS 346 Kbps 15 FPS 184 Kbps 8 FPS 92 Kbps 4 FPS 28 Kbps 1 FPS LEVEL1 415 Kbps 27 FPS 230 Kbps 15 FPS 123 Kbps 8 FPS 61 Kbps 4 FPS 18 Kbps 1 FPS Quality 78_ appendix ❖ H.264 (VGA) Frame Rate 15 FPS 8 FPS 3 FPS 1 FPS LEVEL10 1229 Kbps 10 FPS 737 Kbps 6 FPS 369 Kbps 3 FPS 147 Kbps 1 FPS LEVEL9 1659 Kbps 18 FPS 1014 Kbps 11 FPS 553 Kbps 6 FPS 276 Kbps 3 FPS 111 Kbps 1 FPS LEVEL8 1459 Kbps 19 FPS 845 Kbps 11 FPS 538 Kbps 7 FPS 307 Kbps 4 FPS 92 Kbps 1 FPS LEVEL7 1229 Kbps 20 FPS 737 Kbps 12 FPS 430 Kbps 7 FPS 246 Kbps 4 FPS 74 Kbps 1 FPS LEVEL6 1014 Kbps 22 FPS 691 Kbps 15 FPS 323 Kbps 7 FPS 184 Kbps 4 FPS 55 Kbps 1 FPS LEVEL5 883 Kbps 23 FPS 576 Kbps 15 FPS 269 Kbps 7 FPS 154 Kbps 4 FPS 46 Kbps 1 FPS LEVEL4 707 Kbps 23 FPS 461 Kbps 15 FPS 215 Kbps 7 FPS 123 Kbps 4 FPS 37 Kbps 1 FPS LEVEL3 553 Kbps 24 FPS 346 Kbps 15 FPS 161 Kbps 7 FPS 92 Kbps 4 FPS 28 Kbps 1 FPS LEVEL2 384 Kbps 25 FPS 230 Kbps 15 FPS 108 Kbps 7 FPS 61 Kbps 4 FPS 18 Kbps 1 FPS LEVEL1 200 Kbps 26 FPS 115 Kbps 15 FPS 54 Kbps 7 FPS 31 Kbps 4 FPS 9 Kbps 1 FPS English _79 ● APPENDIX 30 FPS 2089 Kbps 17 FPS Quality appendix ❖ MPEG4 (CIF) Frame Rate 30 FPS 15 FPS 8 FPS 3 FPS 1 FPS LEVEL10 1382 Kbps 30 FPS 691 Kbps 15 FPS 369 Kbps 8 FPS 184 Kbps 4 FPS 55 Kbps 1 FPS LEVEL9 1152 Kbps 30 FPS 576 Kbps 15 FPS 307 Kbps 8 FPS 154 Kbps 4 FPS 46 Kbps 1 FPS LEVEL8 922 Kbps 30 FPS 461 Kbps 15 FPS 246 Kbps 8 FPS 123 Kbps 4 FPS 37 Kbps 1 FPS LEVEL7 691 Kbps 30 FPS 346 Kbps 15 FPS 184 Kbps 8 FPS 92 Kbps 4 FPS 28 Kbps 1 FPS LEVEL6 461 Kbps 30 FPS 230 Kbps 15 FPS 123 Kbps 8 FPS 61 Kbps 4 FPS 18 Kbps 1 FPS LEVEL5 346 Kbps 30 FPS 173 Kbps 15 FPS 92 Kbps 8 FPS 46 Kbps 4 FPS 14 Kbps 1 FPS LEVEL4 288 Kbps 30 FPS 144 Kbps 15 FPS 77 Kbps 8 FPS 38 Kbps 4 FPS 12 Kbps 1 FPS LEVEL3 230 Kbps 30 FPS 115 Kbps 15 FPS 61 Kbps 8 FPS 31 Kbps 4 FPS 9 Kbps 1 FPS LEVEL2 173 Kbps 30 FPS 86 Kbps 15 FPS 46 Kbps 8 FPS 23 Kbps 4 FPS 7 Kbps 1 FPS LEVEL1 151 Kbps 30 FPS 76 Kbps 15 FPS 40 Kbps 8 FPS 20 Kbps 4 FPS 6 Kbps 1 FPS Quality 80_ appendix ❖ H.264 (CIF) Frame Rate 15 FPS 8 FPS 3 FPS 1 FPS LEVEL10 461 Kbps 15 FPS 215 Kbps 7 FPS 123 Kbps 4 FPS 37 Kbps 1 FPS LEVEL9 691 Kbps 30 FPS 346 Kbps 15 FPS 184 Kbps 8 FPS 92 Kbps 4 FPS 28 Kbps 1 FPS LEVEL8 576 Kbps 30 FPS 288 Kbps 15 FPS 134 Kbps 7 FPS 77 Kbps 4 FPS 23 Kbps 1 FPS LEVEL7 461 Kbps 30 FPS 230 Kbps 15 FPS 108 Kbps 7 FPS 61 Kbps 4 FPS 18 Kbps 1 FPS LEVEL6 346 Kbps 30 FPS 173 Kbps 15 FPS 81 Kbps 7 FPS 46 Kbps 4 FPS 14 Kbps 1 FPS LEVEL5 288 Kbps 30 FPS 144 Kbps 15 FPS 67 Kbps 7 FPS 38 Kbps 4 FPS 12 Kbps 1 FPS LEVEL4 230 Kbps 30 FPS 115 Kbps 15 FPS 54 Kbps 7 FPS 31 Kbps 4 FPS 9 Kbps 1 FPS LEVEL3 173 Kbps 30 FPS 86 Kbps 15 FPS 40 Kbps 7 FPS 23 Kbps 4 FPS 7 Kbps 1 FPS LEVEL2 115 Kbps 30 FPS 58 Kbps 15 FPS 27 Kbps 7 FPS 15 Kbps 4 FPS 5 Kbps 1 FPS LEVEL1 58 Kbps 30 FPS 29 Kbps 15 FPS 13 Kbps 7 FPS 8 Kbps 4 FPS 2 Kbps 1 FPS English _81 ● APPENDIX 30 FPS 922 Kbps 30 FPS Quality appendix FRAME RATE (PAL) Test Condition: MJPEG - Resolution(CIF), Quality(1), Frame rate(1) M H.264 - Bitrate control(CBR), Compression(40), Encode Priority(Frame rate), GOP size(15), Deblock(ON), Profile(Baseline), Entropy coding(CAVLC), Motion estimation(HPel) MPEG4 - Bitrate control(CBR), Compression(40), Encode Priority(Frame rate), De-Interlace(ON), GOP size(15) ❖ MPEG4 (4CIF) Frame Rate 25 FPS 13 FPS 6 FPS 3 FPS 1 FPS LEVEL10 4645 Kbps 21 FPS 2654 Kbps 12 FPS 1327 Kbps 6 FPS 664 Kbps 3 FPS 221 Kbps 1 FPS LEVEL9 4055 Kbps 22 FPS 2212 Kbps 12 FPS 1106 Kbps 6 FPS 553 Kbps 3 FPS 184 Kbps 1 FPS LEVEL8 3391 Kbps 23 FPS 1769 Kbps 12 FPS 885 Kbps 6 FPS 442 Kbps 3 FPS 147 Kbps 1 FPS LEVEL7 2544 Kbps 23 FPS 1327 Kbps 12 FPS 664 Kbps 6 FPS 332 Kbps 3 FPS 111 Kbps 1 FPS LEVEL6 1769 Kbps 24 FPS 885 Kbps 12 FPS 442 Kbps 6 FPS 221 Kbps 3 FPS 74 Kbps 1 FPS LEVEL5 1382 Kbps 25 FPS 664 Kbps 12 FPS 332 Kbps 6 FPS 166 Kbps 3 FPS 55 Kbps 1 FPS LEVEL4 1152 Kbps 25 FPS 553 Kbps 12 FPS 276 Kbps 6 FPS 138 Kbps 3 FPS 46 Kbps 1 FPS LEVEL3 922 Kbps 25 FPS 442 Kbps 12 FPS 221 Kbps 6 FPS 111 Kbps 3 FPS 37 Kbps 1 FPS LEVEL2 691 Kbps 25 FPS 332 Kbps 12 FPS 166 Kbps 6 FPS 83 Kbps 3 FPS 28 Kbps 1 FPS LEVEL1 461 Kbps 25 FPS 221 Kbps 12 FPS 111 Kbps 6 FPS 55 Kbps 3 FPS 18 Kbps 1 FPS Quality 82_ appendix ❖ H.264 (4CIF) Frame Rate 13 FPS 6 FPS 3 FPS 1 FPS LEVEL10 1180 Kbps 8 FPS 737 Kbps 5 FPS 442 Kbps 3 FPS 147 Kbps 1 FPS LEVEL9 1991 Kbps 18 FPS 1106 Kbps 10 FPS 664 Kbps 6 FPS 332 Kbps 3 FPS 111 Kbps 1 FPS LEVEL8 1751 Kbps 19 FPS 1014 Kbps 11 FPS 553 Kbps 6 FPS 276 Kbps 3 FPS 92 Kbps 1 FPS LEVEL7 1475 Kbps 20 FPS 885 Kbps 12 FPS 442 Kbps 6 FPS 221 Kbps 3 FPS 74 Kbps 1 FPS LEVEL6 1161 Kbps 21 FPS 664 Kbps 12 FPS 332 Kbps 6 FPS 166 Kbps 3 FPS 55 Kbps 1 FPS LEVEL5 968 Kbps 21 FPS 553 Kbps 12 FPS 276 Kbps 6 FPS 138 Kbps 3 FPS 46 Kbps 1 FPS LEVEL4 811 Kbps 22 FPS 442 Kbps 12 FPS 221 Kbps 6 FPS 111 Kbps 3 FPS 37 Kbps 1 FPS LEVEL3 608 Kbps 22 FPS 332 Kbps 12 FPS 166 Kbps 6 FPS 83 Kbps 3 FPS 28 Kbps 1 FPS LEVEL2 424 Kbps 23 FPS 221 Kbps 12 FPS 111 Kbps 6 FPS 55 Kbps 3 FPS 18 Kbps 1 FPS LEVEL1 230 Kbps 25 FPS 111 Kbps 12 FPS 55 Kbps 6 FPS 28 Kbps 3 FPS 9 Kbps 1 FPS English _83 ● APPENDIX 25 FPS 2359 Kbps 16 FPS Quality appendix ❖ MPEG4 (VGA) Frame Rate 25 FPS 13 FPS 6 FPS 3 FPS 1 FPS LEVEL10 4424 Kbps 20 FPS 2654 Kbps 12 FPS 1327 Kbps 6 FPS 664 Kbps 3 FPS 221 Kbps 1 FPS LEVEL9 3871 Kbps 21 FPS 2212 Kbps 12 FPS 1106 Kbps 6 FPS 553 Kbps 3 FPS 184 Kbps 1 FPS LEVEL8 3097 Kbps 21 FPS 1769 Kbps 12 FPS 885 Kbps 6 FPS 442 Kbps 3 FPS 147 Kbps 1 FPS LEVEL7 2433 Kbps 22 FPS 1327 Kbps 12 FPS 664 Kbps 6 FPS 332 Kbps 3 FPS 111 Kbps 1 FPS LEVEL6 1769 Kbps 24 FPS 885 Kbps 12 FPS 442 Kbps 6 FPS 221 Kbps 3 FPS 74 Kbps 1 FPS LEVEL5 1382 Kbps 25 FPS 664 Kbps 12 FPS 332 Kbps 6 FPS 166 Kbps 3 FPS 55 Kbps 1 FPS LEVEL4 1152 Kbps 25 FPS 553 Kbps 12 FPS 276 Kbps 6 FPS 138 Kbps 3 FPS 46 Kbps 1 FPS LEVEL3 922 Kbps 25 FPS 442 Kbps 12 FPS 221 Kbps 6 FPS 111 Kbps 3 FPS 37 Kbps 1 FPS LEVEL2 691 Kbps 25 FPS 332 Kbps 12 FPS 166 Kbps 6 FPS 83 Kbps 3 FPS 28 Kbps 1 FPS LEVEL1 461 Kbps 25 FPS 221 Kbps 12 FPS 111 Kbps 6 FPS 55 Kbps 3 FPS 18 Kbps 1 FPS Quality 84_ appendix ❖ H.264 (VGA) Frame Rate 13 FPS 6 FPS 3 FPS 1 FPS LEVEL10 1327 Kbps 9 FPS 737 Kbps 5 FPS 442 Kbps 3 FPS 147 Kbps 1 FPS LEVEL9 1991 Kbps 18 FPS 1217 Kbps 11 FPS 664 Kbps 6 FPS 332 Kbps 3 FPS 111 Kbps 1 FPS LEVEL8 1659 Kbps 18 FPS 1106 Kbps 12 FPS 553 Kbps 6 FPS 276 Kbps 3 FPS 92 Kbps 1 FPS LEVEL7 1401 Kbps 19 FPS 885 Kbps 12 FPS 442 Kbps 6 FPS 221 Kbps 3 FPS 74 Kbps 1 FPS LEVEL6 1106 Kbps 20 FPS 664 Kbps 12 FPS 332 Kbps 6 FPS 166 Kbps 3 FPS 55 Kbps 1 FPS LEVEL5 968 Kbps 21 FPS 553 Kbps 12 FPS 276 Kbps 6 FPS 138 Kbps 3 FPS 46 Kbps 1 FPS LEVEL4 774 Kbps 21 FPS 442 Kbps 12 FPS 221 Kbps 6 FPS 111 Kbps 3 FPS 37 Kbps 1 FPS LEVEL3 608 Kbps 22 FPS 332 Kbps 12 FPS 166 Kbps 6 FPS 83 Kbps 3 FPS 28 Kbps 1 FPS LEVEL2 424 Kbps 23 FPS 221 Kbps 12 FPS 111 Kbps 6 FPS 55 Kbps 3 FPS 18 Kbps 1 FPS LEVEL1 230 Kbps 25 FPS 111 Kbps 12 FPS 55 Kbps 6 FPS 28 Kbps 3 FPS 9 Kbps 1 FPS English _85 ● APPENDIX 25 FPS 2507 Kbps 17 FPS Quality appendix ❖ MPEG4 (CIF) Frame Rate 25 FPS 13 FPS 6 FPS 3 FPS 1 FPS LEVEL10 1382 Kbps 25 FPS 664 Kbps 12 FPS 332 Kbps 6 FPS 166 Kbps 3 FPS 55 Kbps 1 FPS LEVEL9 1152 Kbps 25 FPS 553 Kbps 12 FPS 276 Kbps 6 FPS 138 Kbps 3 FPS 46 Kbps 1 FPS LEVEL8 922 Kbps 25 FPS 442 Kbps 12 FPS 221 Kbps 6 FPS 111 Kbps 3 FPS 37 Kbps 1 FPS LEVEL7 691 Kbps 25 FPS 332 Kbps 12 FPS 166 Kbps 6 FPS 83 Kbps 3 FPS 28 Kbps 1 FPS LEVEL6 461 Kbps 25 FPS 221 Kbps 12 FPS 111 Kbps 6 FPS 55 Kbps 3 FPS 18 Kbps 1 FPS LEVEL5 346 Kbps 25 FPS 166 Kbps 12 FPS 83 Kbps 6 FPS 41 Kbps 3 FPS 14 Kbps 1 FPS LEVEL4 288 Kbps 25 FPS 138 Kbps 12 FPS 69 Kbps 6 FPS 35 Kbps 3 FPS 12 Kbps 1 FPS LEVEL3 230 Kbps 25 FPS 111 Kbps 12 FPS 55 Kbps 6 FPS 28 Kbps 3 FPS 9 Kbps 1 FPS LEVEL2 173 Kbps 25 FPS 83 Kbps 12 FPS 41 Kbps 6 FPS 21 Kbps 3 FPS 7 Kbps 1 FPS LEVEL1 151 Kbps 25 FPS 73 Kbps 12 FPS 36 Kbps 6 FPS 18 Kbps 3 FPS 6 Kbps 1 FPS Quality 86_ appendix ❖ H.264 (CIF) Frame Rate 13 FPS 6 FPS 3 FPS 1 FPS LEVEL10 442 Kbps 12 FPS 221 Kbps 6 FPS 111 Kbps 3 FPS 37 Kbps 1 FPS LEVEL9 691 Kbps 25 FPS 332 Kbps 12 FPS 166 Kbps 6 FPS 83 Kbps 3 FPS 28 Kbps 1 FPS LEVEL8 576 Kbps 25 FPS 276 Kbps 12 FPS 138 Kbps 6 FPS 69 Kbps 3 FPS 23 Kbps 1 FPS LEVEL7 461 Kbps 25 FPS 221 Kbps 12 FPS 111 Kbps 6 FPS 55 Kbps 3 FPS 18 Kbps 1 FPS LEVEL6 346 Kbps 25 FPS 166 Kbps 12 FPS 83 Kbps 6 FPS 41 Kbps 3 FPS 14 Kbps 1 FPS LEVEL5 288 Kbps 25 FPS 138 Kbps 12 FPS 69 Kbps 6 FPS 35 Kbps 3 FPS 12 Kbps 1 FPS LEVEL4 230 Kbps 25 FPS 111 Kbps 12 FPS 55 Kbps 6 FPS 28 Kbps 3 FPS 9 Kbps 1 FPS LEVEL3 173 Kbps 25 FPS 83 Kbps 12 FPS 41 Kbps 6 FPS 21 Kbps 3 FPS 7 Kbps 1 FPS LEVEL2 115 Kbps 25 FPS 55 Kbps 12 FPS 28 Kbps 6 FPS 14 Kbps 3 FPS 5 Kbps 1 FPS LEVEL1 58 Kbps 25 FPS 28 Kbps 12 FPS 14 Kbps 6 FPS 7 Kbps 3 FPS 2 Kbps 1 FPS English _87 ● APPENDIX 25 FPS 922 Kbps 25 FPS Quality appendix TROUBLESHOOTING PROBLEM SOLUTION y Check to make sure that the camera’s Network settings are appropriate. y Check to make sure that all network cables have been connected properly. I can’t access the camera from a web browser. y If connected using DHCP, verify that the camera is able to acquire dynamic IP addresses without any problem. y If connected using a DDNS URL, verify that the MAC address has been properly entered. y If the camera is connected to a router, verify that port forwarding is properly configured. y Connected Viewers become disconnected upon any change to camera or network configurations. Viewer got disconnected during monitoring. y Check all network connections. I cannot connect to the system using a tab browser of Internet Explorer 7.0. y When you try to connect to the system using a tab browser, the same cookie information is shared, resulting in errors when connected. Therefore, instead of using a tab browser, open a new browser window to connect to the system. The camera connected to the network is not detected in the IP installer program. y Turn off the firewall settings on your PC and then search the camera again. Images overlap. y Check whether two or more cameras are set to a single multicast address instead of different addresses. If a single address is used for multiple cameras, the images may overlap. No image appears. y If the transmission method is set to multicast, check whether there is a router that supports multicast in the LAN the camera is connected to. 88_ appendix y If the camera is connected over an xDSL network, it’ s possible for Viewer to disconnect under poor network conditions. PROBLEM I enabled Motion Detection Feature under Motion Detection, but .jpg files are not getting sent over FTP/ SMTP even after motion detection occurs at the FT camera. SOLUTION y Verify the settings in the following sequence: A. NTP must be properly configured. B. Motion Detection Feature must be enabled. C. Alarm Video Transmission must be enabled. D. Check for scheduling conflict. y Yes. Motion Zone can be configured independently of whether or not Motion Detection Feature is in use. A motion event took place but didn’t trigger an alarm. y Check alarm output port settings. Cannot record into the SD memory y Check if the memory card is defective. card. y Check if the write protection tab of the memory card is set to “Lock”. y Check if the memory card is defective. SD memory indicator does not turn on even when the SD memory y Check if the <Record> is checked in <Setup> <Event> <SD Card card is inserted. Record> menu. SD memory card is inserted but the camera does not operate properly. Cannot format the SD memory card. y Check if the memory card is inserted in the proper direction. Operation of memory card that is formatted by other devices is not guaranteed with this camera unit y Format the memory card again in <Setup> <Event> <SD Card> menu. y Check if the write protection tab of the memory card is set to “Lock”. English _89 ● APPENDIX Is it possible to configure Motion Zone with Motion Detection Feature disabled? GPL/LGPL SOFTWARE LICENSE The software included in this product contains copyrighted software that is licensed under the GPL/LGPL. You may obtain the complete Corresponding Source code from us for a period of three years after our last shipment of this product by sending email to [email protected] If you want to obtain the complete Corresponding Source code in the physical medium such as CD-ROM, the cost of physically performing source distribution might be charged. y GPL S/W - Base Kernel, Busybox, Sysvinit, dosfstools y LGPL S/W - gLibc, Inetutils GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright © 1989, 1991 Free Software Foundation, Inc. 51 Franklin Street,Fifth Floor, Boston, MA 02110-1301, USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. Preamble The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software-- to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation's software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by the GNU Lesser General Public License instead.) You can apply it to your programs, too. When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs ; and that you know you can do these things. To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it. For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights. We protect your rights with two steps : (1)copyright the software, and (2)offer you this license which gives you legal permission to copy, distribute and/or modify the software. Also, for each author's protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors' reputations. Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone's free use or not licensed at all. The precise terms and conditions for copying, distribution and modification follow. TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc. 51 Franklin S 0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The "Program", below, refers to any such program or work, and a "work based on the Program" means either the Program or any derivative work under copyright law : that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated into another language. (Hereinafter, translation is included without limitation in the term "modification".) Each licensee is addressed as "you". Activities other than copying, distribution and modification are not covered by this License ; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does. 1. You may copy and distribute verbatim copies of the Program's source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty ; and give any other recipients of the Program a copy of this License along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions : a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change. b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License. c) If the modified program normally reads commands interactively when run,you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception:if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.) These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you ; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Program. In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program)on a volume of a storage or distribution medium does not bring the other work under the scope of this License. 3. You may copy and distribute the Program (or a work based on it, under Section 2)in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following : a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange ; or, b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machinereadable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange ; or, c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.) The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form)with the major components (compiler, kernel, and so on)of the operating system on which the executable runs, unless that component itself accompanies the executable. your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program. If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system ; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice. This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License. 4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance. 5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License.Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it. 6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License. 7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise)that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously 8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries,so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License. 9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free Software Foundation. 10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation,write to the Free Software Foundation ; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally. NO WARRANTY 11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "ASIS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAMPROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. END OF TERMS AND CONDITIONS How to Apply These Terms to Your New Programs If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms. To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty ; and each file should have at least the "copyright" line and a pointer to where the full notice is found. one line to give the program's name and an idea of what it does. Copyright (C)yyyy name of author This program is free software ; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation ; either version 2 of the License, or (at your option)any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY ; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program ; if not, write to the Free Software Foundation, Inc.,51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA. Also add information on how to contact you by electronic and paper mail. If the program is interactive, make it output a short notice like this when it starts in an interactive mode : Gnomovision version 69, Copyright (C) year name of author Gnomovision comes with ABSOLUTELY NO WARRANTY ; for details type ‘show w’. This is free software, and you are welcome to redistribute it under certain conditions ; type ‘show c’ for details. The hypothetical commands ‘show w’ and ‘show c’ should show the appropriate parts of the General Public License. Of course, the commands you use may be called something other than ‘show w’ and ‘show c’ ; they could even be mouse-clicks or menu items-- whatever suits your program. You should also get your employer (if you work as a programmer)or your school, if any, to sign a "copyright disclaimer" for the program,if necessary. Here is a sample ; alter the names: Yoyodyne, Inc.,hereby disclaims all copyright interest in the program ‘Gnomovision’ (which makes passes at compilers) written by James Hacker. signature of Ty Coon, 1 April 1989 Ty Coon, President of Vice This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the GNU Lesser General Public License instead of this License. GNU GENERAL PUBLIC LICENSE Version 3, 29 June 2007 Copyright © 2007 Free Software Foundation, Inc. <http://fsf.org/> Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. Preamble The GNU General Public License is a free, copyleft license for software and other kinds of works. The licenses for most software and other practical works are designed to take away your freedom to share and change the works. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change all versions of a program--to make sure it remains free software for all its users. We, the Free Software Foundation, use the GNU General Public License for most of our software; it applies also to any other work released this way by its authors. You can apply it to your programs, too. When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for them if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs, and that you know you can do these things. To protect your rights, we need to prevent others from denying you these rights or asking you to surrender the rights. Therefore, you have certain responsibilities if you distribute copies of the software, or if you modify it: responsibilities to respect the freedom of others. For example, if you distribute copies of such a program, whether gratis or for a fee, you must pass on to the recipients the same freedoms that you received. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights. Developers that use the GNU GPL protect your rights with two steps: (1) assert copyright on the software, and (2) offer you this License giving you legal permission to copy, distribute and/or modify it. For the developers' and authors' protection, the GPL clearly explains that there is no warranty for this free software. For both users' and authors' sake, the GPL requires that modified versions be marked as changed, so that their problems will not be attributed erroneously to authors of previous versions. Some devices are designed to deny users access to install or run modified versions of the software inside them, although the manufacturer can do so. This is fundamentally incompatible with the aim of protecting users' freedom to change the software. The systematic pattern of such abuse occurs in the area of products for individuals to use, which is precisely where it is most unacceptable. Therefore, we have designed this version of the GPL to prohibit the practice for those products. If such problems arise substantially in other domains, we stand ready to extend this provision to those domains in future versions of the GPL, as needed to protect the freedom of users. Finally, every program is threatened constantly by software patents. States should not allow patents to restrict development and use of software on generalpurpose computers, but in those that do, we wish to avoid the special danger that patents applied to a free program could make it effectively proprietary. To prevent this, the GPL assures that patents cannot be used to render the program non-free. The precise terms and conditions for copying, distribution and modification follow. TERMS AND CONDITIONS 0. Definitions. “This License” refers to version 3 of the GNU General Public License. “Copyright” also means copyright-like laws that apply to other kinds of works, such as semiconductor masks. “The Program” refers to any copyrightable work licensed under this License. Each licensee is addressed as “you”. “Licensees” and “recipients” may be individuals or organizations. To “modify” a work means to copy from or adapt all or part of the work in a fashion requiring copyright permission, other than the making of an exact copy. The resulting work is called a “modified version” of the earlier work or a work “based on” the earlier work. A “covered work” means either the unmodified Program or a work based on the Program. To “propagate” a work means to do anything with it that, without permission, would make you directly or secondarily liable for infringement under applicable copyright law, except executing it on a computer or modifying a private copy. Propagation includes copying, distribution (with or without modification), making available to the public, and in some countries other activities as well. shared libraries and dynamically linked subprograms that the work is specifically designed to require, such as by intimate data communication or control flow between those subprograms and other parts of the work. To “convey” a work means any kind of propagation that enables other parties to make or receive copies. Mere interaction with a user through a computer network, with no transfer of a copy, is not conveying. The Corresponding Source need not include anything that users can regenerate automatically from other parts of the Corresponding Source. An interactive user interface displays “Appropriate Legal Notices” to the extent that it includes a convenient and prominently visible feature that (1) displays an appropriate copyright notice, and (2) tells the user that there is no warranty for the work (except to the extent that warranties are provided), that licensees may convey the work under this License, and how to view a copy of this License. If the interface presents a list of user commands or options, such as a menu, a prominent item in the list meets this criterion. 1. Source Code. The “source code” for a work means the preferred form of the work for making modifications to it. “Object code” means any non-source form of a work. A “Standard Interface” means an interface that either is an official standard defined by a recognized standards body, or, in the case of interfaces specified for a particular programming language, one that is widely used among developers working in that language. The “System Libraries” of an executable work include anything, other than the work as a whole, that (a) is included in the normal form of packaging a Major Component, but which is not part of that Major Component, and (b) serves only to enable use of the work with that Major Component, or to implement a Standard Interface for which an implementation is available to the public in source code form. A “Major Component”, in this context, means a major essential component (kernel, window system, and so on) of the specific operating system (if any) on which the executable work runs, or a compiler used to produce the work, or an object code interpreter used to run it. The “Corresponding Source” for a work in object code form means all the source code needed to generate, install, and (for an executable work) run the object code and to modify the work, including scripts to control those activities. However, it does not include the work's System Libraries, or general-purpose tools or generally available free programs which are used unmodified in performing those activities but which are not part of the work. For example, Corresponding Source includes interface definition files associated with source files for the work, and the source code for The Corresponding Source for a work in source code form is that same work. 2. Basic Permissions. All rights granted under this License are granted for the term of copyright on the Program, and are irrevocable provided the stated conditions are met. This License explicitly affirms your unlimited permission to run the unmodified Program. The output from running a covered work is covered by this License only if the output, given its content, constitutes a covered work. This License acknowledges your rights of fair use or other equivalent, as provided by copyright law. You may make, run and propagate covered works that you do not convey, without conditions so long as your license otherwise remains in force. You may convey covered works to others for the sole purpose of having them make modifications exclusively for you, or provide you with facilities for running those works, provided that you comply with the terms of this License in conveying all material for which you do not control copyright. Those thus making or running the covered works for you must do so exclusively on your behalf, under your direction and control, on terms that prohibit them from making any copies of your copyrighted material outside their relationship with you. Conveying under any other circumstances is permitted solely under the conditions stated below. Sublicensing is not allowed; section 10 makes it unnecessary. 3. Protecting Users' Legal Rights From AntiCircumvention Law. No covered work shall be deemed part of an effective technological measure under any applicable law fulfilling obligations under article 11 of the WIPO copyright treaty adopted on 20 December 1996, or similar laws prohibiting or restricting circumvention of such measures. When you convey a covered work, you waive any legal power to forbid circumvention of technological measures to the extent such circumvention is effected by exercising rights under this License with respect to the covered work, and you disclaim any intention to limit operation or modification of the work as a means of enforcing, against the work's users, your or third parties' legal rights to forbid circumvention of technological measures. work in an aggregate does not cause this License to apply to the other parts of the aggregate. 6. Conveying Non-Source Forms. 4. Conveying Verbatim Copies. You may convey verbatim copies of the Program's source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice; keep intact all notices stating that this License and any non-permissive terms added in accord with section 7 apply to the code; keep intact all notices of the absence of any warranty; and give all recipients a copy of this License along with the Program. You may charge any price or no price for each copy that you convey, and you may offer support or warranty protection for a fee. 5. Conveying Modified Source Versions. You may convey a work based on the Program, or the modifications to produce it from the Program, in the form of source code under the terms of section 4, provided that you also meet all of these conditions: a) The work must carry prominent notices stating that you modified it, and giving a relevant date. b) The work must carry prominent notices stating that it is released under this License and any conditions added under section 7. This requirement modifies the requirement in section 4 to “keep intact all notices”. c) You must license the entire work, as a whole, under this License to anyone who comes into possession of a copy. This License will therefore apply, along with any applicable section 7 additional terms, to the whole of the work, and all its parts, regardless of how they are packaged. This License gives no permission to license the work in any other way, but it does not invalidate such permission if you have separately received it. d) If the work has interactive user interfaces, each must display Appropriate Legal Notices; however, if the Program has interactive interfaces that do not display Appropriate Legal Notices, your work need not make them do so. A compilation of a covered work with other separate and independent works, which are not by their nature extensions of the covered work, and which are not combined with it such as to form a larger program, in or on a volume of a storage or distribution medium, is called an “aggregate” if the compilation and its resulting copyright are not used to limit the access or legal rights of the compilation's users beyond what the individual works permit. Inclusion of a covered You may convey a covered work in object code form under the terms of sections 4 and 5, provided that you also convey the machine-readable Corresponding Source under the terms of this License, in one of these ways: a) Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by the Corresponding Source fixed on a durable physical medium customarily used for software interchange. b) Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by a written offer, valid for at least three years and valid for as long as you offer spare parts or customer support for that product model, to give anyone who possesses the object code either (1) a copy of the Corresponding Source for all the software in the product that is covered by this License, on a durable physical medium customarily used for software interchange, for a price no more than your reasonable cost of physically performing this conveying of source, or (2) access to copy the Corresponding Source from a network server at no charge. c) Convey individual copies of the object code with a copy of the written offer to provide the corresponding Source. This alternative is allowed only occasionally and noncommercially, and only if you received the object code with such an offer, in accord with subsection 6b. d) Convey the object code by offering access from a designated place (gratis or for a charge), and offer equivalent access to the Corresponding Source in the same way through the same place at no further charge. You need not require recipients to copy the Corresponding Source along with the object code. If the place to copy the object code is a network server, the Corresponding Source may be on a different server (operated by you or a third party) that supports equivalent copying facilities, provided you maintain clear directions next to the object code saying where to find the Corresponding Source. Regardless of what server hosts the Corresponding Source, you remain obligated to ensure that it is available for as long as needed to satisfy these requirements. e) Convey the object code using peer-to-peer transmission, provided you inform other peers where the object code and Corresponding Source of the work are being offered to the general public at no charge under subsection 6d. A separable portion of the object code, whose source code is excluded from the Corresponding Source as a System Library, need not be included in conveying the object code work. A “User Product” is either (1) a “consumer product”, which means any tangible personal property which is normally used for personal, family, or household purposes, or (2) anything designed or sold for incorporation into a dwelling. In determining whether a product is a consumer product, doubtful cases shall be resolved in favor of coverage. For a particular product received by a particular user, “normally used” refers to a typical or common use of that class of product, regardless of the status of the particular user or of the way in which the particular user actually uses, or expects or is expected to use, the product. A product is a consumer product regardless of whether the product has substantial commercial, industrial or non-consumer uses, unless such uses represent the only significant mode of use of the product. “Installation Information” for a User Product means any methods, procedures, authorization keys, or other information required to install and execute modified versions of a covered work in that User Product from a modified version of its Corresponding Source. The information must suffice to ensure that the continued functioning of the modified object code is in no case prevented or interfered with solely because modification has been made. If you convey an object code work under this section in, or with, or specifically for use in, a User Product, and the conveying occurs as part of a transaction in which the right of possession and use of the User Product is transferred to the recipient in perpetuity or for a fixed term (regardless of how the transaction is characterized), the Corresponding Source conveyed under this section must be accompanied by the Installation Information. But this requirement does not apply if neither you nor any third party retains the ability to install modified object code on the User Product (for example, the work has been installed in ROM). The requirement to provide Installation Information does not include a requirement to continue to provide support service, warranty, or updates for a work that has been modified or installed by the recipient, or for the User Product in which it has been modified or installed. Access to a network may be denied when the modification itself materially and adversely affects the operation of the network or violates the rules and protocols for communication across the network. Corresponding Source conveyed, and Installation Information provided, in accord with this section must be in a format that is publicly documented (and with an implementation available to the public in source code form), and must require no special password or key for unpacking, reading or copying. 7. Additional Terms. “Additional permissions” are terms that supplement the terms of this License by making exceptions from one or more of its conditions. Additional permissions that are applicable to the entire Program shall be treated as though they were included in this License, to the extent that they are valid under applicable law. If additional permissions apply only to part of the Program, that part may be used separately under those permissions, but the entire Program remains governed by this License without regard to the additional permissions. When you convey a copy of a covered work, you may at your option remove any additional permissions from that copy, or from any part of it. (Additional permissions may be written to require their own removal in certain cases when you modify the work.) You may place additional permissions on material, added by you to a covered work, for which you have or can give appropriate copyright permission. Notwithstanding any other provision of this License, for material you add to a covered work, you may (if authorized by the copyright holders of that material) supplement the terms of this License with terms: a) Disclaiming warranty or limiting liability differently from the terms of sections 15 and 16 of this License; or b) Requiring preservation of specified reasonable legal notices or author attributions in that material or in the Appropriate Legal Notices displayed by works containing it; or c) Prohibiting misrepresentation of the origin of that material, or requiring that modified versions of such material be marked in reasonable ways as different from the original version; or d) Limiting the use for publicity purposes of names of licensors or authors of the material; or e) Declining to grant rights under trademark law for use of some trade names, trademarks, or service marks; or f) Requiring indemnification of licensors and authors of that material by anyone who conveys the material (or modified versions of it) with contractual assumptions of liability to the recipient, for any liability that these contractual assumptions directly impose on those licensors and authors. All other non-permissive additional terms are considered “further restrictions” within the meaning of section 10. If the Program as you received it, or any part of it, contains a notice stating that it is governed by this License along with a term that is a further restriction, you may remove that term. If a license document contains a further restriction but permits relicensing or conveying under this License, you may add to a covered work material governed by the terms of that license document, provided that the further restriction does not survive such relicensing or conveying. If you add terms to a covered work in accord with this section, you must place, in the relevant source files, a statement of the additional terms that apply to those files, or a notice indicating where to find the applicable terms. Additional terms, permissive or non-permissive, may be stated in the form of a separately written license, or stated as exceptions; the above requirements apply either way. 8. Termination. You may not propagate or modify a covered work except as expressly provided under this License. Any attempt otherwise to propagate or modify it is void, and will automatically terminate your rights under this License (including any patent licenses granted under the third paragraph of section 11). However, if you cease all violation of this License, then your license from a particular copyright holder is reinstated (a) provisionally, unless and until the copyright holder explicitly and finally terminates your license, and (b) permanently, if the copyright holder fails to notify you of the violation by some reasonable means prior to 60 days after the cessation. Moreover, your license from a particular copyright holder is reinstated permanently if the copyright holder notifies you of the violation by some reasonable means, this is the first time you have received notice of violation of this License (for any work) from that copyright holder, and you cure the violation prior to 30 days after your receipt of the notice. Termination of your rights under this section does not terminate the licenses of parties who have received copies or rights from you under this License. If your rights have been terminated and not permanently reinstated, you do not qualify to receive new licenses for the same material under section 10. 9. Acceptance Not Required for Having Copies. You are not required to accept this License in order to receive or run a copy of the Program. Ancillary propagation of a covered work occurring solely as a consequence of using peer-to-peer transmission to receive a copy likewise does not require acceptance. However, nothing other than this License grants you permission to propagate or modify any covered work. These actions infringe copyright if you do not accept this License. Therefore, by modifying or propagating a covered work, you indicate your acceptance of this License to do so. 10. Automatic Licensing of Downstream Recipients. Each time you convey a covered work, the recipient automatically receives a license from the original licensors, to run, modify and propagate that work, subject to this License. You are not responsible for enforcing compliance by third parties with this License. An “entity transaction” is a transaction transferring control of an organization, or substantially all assets of one, or subdividing an organization, or merging organizations. If propagation of a covered work results from an entity transaction, each party to that transaction who receives a copy of the work also receives whatever licenses to the work the party's predecessor in interest had or could give under the previous paragraph, plus a right to possession of the Corresponding Source of the work from the predecessor in interest, if the predecessor has it or can get it with reasonable efforts. You may not impose any further restrictions on the exercise of the rights granted or affirmed under this License. For example, you may not impose a license fee, royalty, or other charge for exercise of rights granted under this License, and you may not initiate litigation (including a cross-claim or counterclaim in a lawsuit) alleging that any patent claim is infringed by making, using, selling, offering for sale, or importing the Program or any portion of it. 11. Patents. A “contributor” is a copyright holder who authorizes use under this License of the Program or a work on which the Program is based. The work thus licensed is called the contributor's “contributor version”. A contributor's “essential patent claims” are all patent claims owned or controlled by the contributor, whether already acquired or hereafter acquired, that would be infringed by some manner, permitted by this License, of making, using, or selling its contributor version, but do not include claims that would be infringed only as a consequence of further modification of the contributor version. For purposes of this definition, “control” includes the right to grant patent sublicenses in a manner consistent with the requirements of this License. Each contributor grants you a non-exclusive, worldwide, royalty-free patent license under the contributor's essential patent claims, to make, use, sell, offer for sale, import and otherwise run, modify and propagate the contents of its contributor version. In the following three paragraphs, a “patent license” is any express agreement or commitment, however denominated, not to enforce a patent (such as an express permission to practice a patent or covenant not to sue for patent infringement). To “grant” such a patent license to a party means to make such an agreement or commitment not to enforce a patent against the party. If you convey a covered work, knowingly relying on a patent license, and the Corresponding Source of the work is not available for anyone to copy, free of charge and under the terms of this License, through a publicly available network server or other readily accessible means, then you must either (1) cause the Corresponding Source to be so available, or (2) arrange to deprive yourself of the benefit of the patent license for this particular work, or (3) arrange, in a manner consistent with the requirements of this License, to extend the patent license to downstream recipients. “Knowingly relying” means you have actual knowledge that, but for the patent license, your conveying the covered work in a country, or your recipient's use of the covered work in a country, would infringe one or more identifiable patents in that country that you have reason to believe are valid. If, pursuant to or in connection with a single transaction or arrangement, you convey, or propagate by procuring conveyance of, a covered work, and grant a patent license to some of the parties receiving the covered work authorizing them to use, propagate, modify or convey a specific copy of the covered work, then the patent license you grant is automatically extended to all recipients of the covered work and works based on it. A patent license is “discriminatory” if it does not include within the scope of its coverage, prohibits the exercise of, or is conditioned on the non-exercise of one or more of the rights that are specifically granted under this License. You may not convey a covered work if you are a party to an arrangement with a third party that is in the business of distributing software, under which you make payment to the third party based on the extent of your activity of conveying the work, and under which the third party grants, to any of the parties who would receive the covered work from you, a discriminatory patent license (a) in connection with copies of the covered work conveyed by you (or copies made from those copies), or (b) primarily for and in connection with specific products or compilations that contain the covered work, unless you entered into that arrangement, or that patent license was granted, prior to 28 March 2007. Nothing in this License shall be construed as excluding or limiting any implied license or other defenses to infringement that may otherwise be available to you under applicable patent law. 12. No Surrender of Others' Freedom. If conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot convey a covered work so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not convey it at all. For example, if you agree to terms that obligate you to collect a royalty for further conveying from those to whom you convey the Program, the only way you could satisfy both those terms and this License would be to refrain entirely from conveying the Program. 13. Use with the GNU Affero General Public License. Notwithstanding any other provision of this License, you have permission to link or combine any covered work with a work licensed under version 3 of the GNU Affero General Public License into a single combined work, and to convey the resulting work. The terms of this License will continue to apply to the part which is the covered work, but the special requirements of the GNU Affero General Public License, section 13, concerning interaction through a network will apply to the combination as such. 14. Revised Versions of this License. The Free Software Foundation may publish revised and/ or new versions of the GNU General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the Program specifies that a certain numbered version of the GNU General Public License “or any later version” applies to it, you have the option of following the terms and conditions either of that numbered version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of the GNU General Public License, you may choose any version ever published by the Free Software Foundation. If the Program specifies that a proxy can decide which future versions of the GNU General Public License can be used, that proxy's public statement of acceptance of a version permanently authorizes you to choose that version for the Program. Later license versions may give you additional or different permissions. However, no additional obligations are imposed on any author or copyright holder as a result of your choosing to follow a later version. 15. Disclaimer of Warranty. THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 16. Limitation of Liability. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MODIFIES AND/OR CONVEYS THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. [This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.] Preamble The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and change free software to make sure the software is free for all its users. This license, the Lesser General Public License, applies to some specially designated software packages-typically libraries-of the Free Software Foundation and other authors who decide to use it. You can use it too, but we suggest you first think carefully about whether this license or the ordinary General Public License is the better strategy to use in any particular case, based on the explanations below. When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish); that you receive source code or can get it if you want it; that you can change the software and use pieces of it in new free programs; and that you are informed that you can do these things. To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it. 17. Interpretation of Sections 15 and 16. If the disclaimer of warranty and limitation of liability provided above cannot be given local legal effect according to their terms, reviewing courts shall apply local law that most closely approximates an absolute waiver of all civil liability in connection with the Program, unless a warranty or assumption of liability accompanies a copy of the Program in return for a fee. END OF TERMS AND CONDITIONS GNU LESSER GENERAL PUBLIC LICENSE Version 2.1, February 1999 Copyright © 1991, 1999 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code. If you link other code with the library, you must provide complete object files to the recipients, so that they can relink them with the library after making changes to the library and recompiling it. And you must show them these terms so they know their rights. We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives you legal permission to copy, distribute and/or modify the library. To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the library is modified by someone else and passed on, the recipients should know that what they have is not the original version, so that the original author’s reputation will not be affected by problems that might be introduced by others. Although the Lesser General Public License is Less protective of the users’ freedom, it does ensure that the user of a program that is linked with the Library has the freedom and the wherewithal to run that program using a modified version of the Library. Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a company cannot effectively restrict the users of a free program by obtaining a restrictive license from a patent holder. Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full freedom of use specified in this license. The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a “work based on the library” and a “work that uses the library”. The former contains code derived from the library, whereas the latter must be combined with the library in order to run. Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license, the GNU Lesser General Public License, applies to certain designated libraries, and is quite different from the ordinary General Public License. We use this license for certain libraries in order to permit linking those libraries into non-free programs. When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work, a derivative of the original library. The ordinary General Public License therefore permits such linking only if the entire combination fits its criteria of freedom. The Lesser General Public License permits more lax criteria for linking other code with the library. We call this license the “Lesser” General Public License because it does Less to protect the user’ s freedom than the ordinary General Public License. It also provides other free software developers Less of an advantage over competing non-free programs. These disadvantages are the reason we use the ordinary General Public License for many libraries. However, the Lesser license provides advantages in certain special circumstances. For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it becomes a de-facto standard. To achieve this, non-free programs must be allowed to use the library. A more frequent case is that a free library does the same job as widely used non-free libraries. In this case, there is little to gain by limiting the free library to free software only, so we use the Lesser General Public License. In other cases, permission to use a particular library in non-free programs enables a greater number of people to use a large body of free software. For example, permission to use the GNU C Library in non-free programs enables many more people to use the whole GNU operating system, as well as its variant, the GNU/ Linux operating system. TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0. This License Agreement applies to any software library or other program which contains a notice placed by the copyright holder or other authorized party saying it may be distributed under the terms of this Lesser General Public License (also called “this License”). Each licensee is addressed as “you”. A “library” means a collection of software functions and/ or data prepared so as to be conveniently linked with application programs (which use some of those functions and data) to form executables. The “Library”, below, refers to any such software library or work which has been distributed under these terms. A “work based on the Library” means either the Library or any derivative work under copyright law: that is to say, a work containing the Library or a portion of it, either verbatim or with modifications and/or translated straightforwardly into another language. (Hereinafter, translation is included without limitation in the term “modification”.) “Source code” for a work means the preferred form of the work for making modifications to it. For a library, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the library. Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running a program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the Library (independent of the use of the Library in a tool for writing it). Whether that is true depends on what the Library does and what the program that uses the Library does. 1. You may copy and distribute verbatim copies of the Library’s complete source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and distribute a copy of this License along with the Library. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) The modified work must itself be a software library. b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change. c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this License. d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful. (For example, a function in a library to compute square roots has a purpose that is entirely well-defined independent of the application. Therefore, Subsection 2d requires that any application-supplied function or table used by this function must be optional: if the application does not supply it, the square root function must still compute square roots.) These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Library, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Library, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Library. In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the Library) on a volume of a storage or distribution medium does not bring the other work under the scope of this License. 3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library. To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General Public License, version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other change in these notices. Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies to all subsequent copies and derivative works made from that copy. This option is useful when you wish to copy part of the code of the Library into a program that is not a library. 4. You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided t hat you accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange. If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place satisfies the requirement to distribute the source code, even though third parties are not compelled to copy the source along with the object code. 5. A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being compiled or linked with it, is called a “work that uses the Library”. Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of this License. However, linking a “work that uses the Library” with the Library creates an executable that is a derivative of the Library (because it contains portions of the Library), rather than a “work that uses the library”. The executable is therefore covered by this License. Section 6 states terms for distribution of such executables. When a “work that uses the Library” uses material from a header file that is part of the Library, the object code for the work may be a derivative work of the Library even though the source code is not. Whether this is true is especially significant if the work can be linked without the Library, or if the work is itself a library. The threshold for this to be true is not precisely defined by law. If such an object file uses only numerical parameters, data structure layouts and accessors, and small macros and small inline functions (ten lines or less in length), then the use of the object file is unrestricted, regardless of whether it is legally a derivative work. (Executables containing this object code plus portions of the Library will still fall under Section 6.) Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section 6. Any executables containing that work also fall under Section 6, whether or not they are linked directly with the Library itself. 6. As an exception to the Sections above, you may also combine or link a “work that uses the Library” with the Library to produce a work containing portions of the Library, and distribute that work under terms of your choice, provided that the terms permit modification of the work for the customer’ s own use and reverse engineering for debugging such modifications. You must give prominent notice with each copy of the work that the Library is used in it and that the Library and its use are covered by this License. You must supply a copy of this License. If the work during execution displays copyright notices, you must include the copyright notice for the Library among them, as well as a reference directing the user to the copy of this License. Also, you must do one of these things: a) Accompany the work with the complete corresponding machine-readable source code for the Library including whatever changes were used in the work (which must be distributed under Sections 1 and 2 above); and, if the work is an executable linked with the Library, with the complete machine readable “work that uses the Library”, as object code and/or source code, so that the user can modify the Library and then relink to produce a modified executable containing the modified Library. (It is understood that the user who changes the contents of definitions files in the Library will not necessarily be able to recompile the application to use the modified definitions.) b) Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that (1) uses at run time a copy of the library already present on the user’s computer system, rather than copying library functions into the executable, and (2) will operate properly with a modified version of the library, if the user installs one, as long as the modified version is interface-compatible with the version that the work was made with. c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in Subsection 6a, above, for a charge no more than the cost of performing this distribution. d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the above specified materials from the same place. e) Verify that the user has already received a copy of these materials or that you have already sent this user a copy. For an executable, the required form of the “work that uses the Library” must include any data and utility programs needed for reproducing the executable from it. However, as a special exception, the materials to be distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system. Such a contradiction means you cannot use both them and the Library together in an executable that you distribute. 7. You may place library facilities that are a work based on the Library side-by-side in a single library together with other library facilities not covered by this License, and distribute such a combined library, provided that the separate distribution of the work based on the Library and of the other library facilities is otherwise permitted, and provided that you do these two things: a) Accompany the combined library with a copy of the same work based on the Library, uncombined with any other library facilities. This must be distributed under the terms of the Sections above. b) Give prominent notice with the combined library of the fact that part of it is a work based on the Library, and explaining where to find the accompanying uncombined form of the same work. 8. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the Library is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance. 9. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Library or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Library (or any work based on the Library), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Library or works based on it. 10. Each time you redistribute the Library (or any work based on the Library), the recipient automatically receives a license from the original licensor to copy, distribute, link with or modify the Library subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties with this License. 11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Library at all. For example, if a patent license would not permit royalty free redistribution of the Library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Library. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice. This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License. 12. If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License. 13. The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the Library specifies a version number of this License which applies to it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Library does not specify a license version number, you may choose any version ever published by the Free Software Foundation. 14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with these, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally. NO WARRANTY 15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. END OF TERMS AND CONDITIONS How to Apply These Terms to Your New Libraries If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it free software that everyone can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General Public License). To apply these terms, attach the following notices to the library. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the “copyright” line and a pointer to where the full notice is found. one line to give the library’s name and an idea of what it does. Copyright © year name of author This library is free software; you can redistribute it and/ or modify it under the terms of the GNU Lesser General Public License as published by the Free Software Foundation; either version 2.1 of the License, or (at your option) any later version. This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more details. You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Also add information on how to contact you by electronic and paper mail. You should also get your employer (if you work as a programmer) or your school, if any, to sign a “copyright disclaimer” for the library, if necessary. Here is a sample; alter the names: Yoyodyne, Inc., hereby disclaims all copyright interest in the library ‘Frob’ (a library for tweaking knobs) written by James Random Hacker. signature of Ty Coon, 1 April 1990 Ty Coon, President of Vice. OpenSSL LICENSE Copyright © 1998-2006 The OpenSSL Project. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/ or other materials provided with the distribution. 3. All advertising materials mentioning features or use of this software must display the following acknowledgment: “This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)” 4. The names “OpenSSL Toolkit” and “OpenSSL Project” must not be used to endorse or promote products derived from this software without prior written permission. For written permission, please contact [email protected]. 5. Products derived from this software may not be called “OpenSSL” nor may “OpenSSL” appear in their names without prior written permission of the OpenSSL Project. 6. Redistributions of any form whatsoever must retain the following acknowledgment: “This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/)” THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT “AS IS” AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. This product includes cryptographic software written by Eric Young ([email protected]). This product includes software written by Tim Hudson([email protected]). Original SSLeay License Copyright (C) 1995-1998 Eric Young (eay@cryptsoft. com) All rights reserved. This package is an SSL implementation written by Eric Young (eay@cryptsoft. com). The implementation was written so as to conform with Netscapes SSL. This library is free for commercial and non-commercial use as long as the following conditions are aheared to. The following conditions apply to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code. The SSL documentation included with this distribution is covered by the same copyright terms except that the holder is Tim Hudson (tjh@ cryptsoft.com). Copyright remains Eric Young’s, and as such any Copyright notices in the code are not to be removed. If this package is used in a product, Eric Young should be given attribution as the author of the parts of the library used. This can be in the form of a textual message at program startup or in documentation (online or textual) provided with the package. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/ or other materials provided with the distribution. 3. All advertising materials mentioning features or use of this software must display the following acknowledgement: “This product includes cryptographic software written by Eric Young (eay@ cryptsoft.com)” The word ‘cryptographic’ can be left out if the rouines from the library being used are not cryptographic related :-). 4. If you include any Windows specific code (or a derivative thereof) from the apps directory (application code) you must include an acknowledgement: “This product includes software written by Tim Hudson (tjh@ cryptsoft.com)” THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ‘‘AS IS AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. The licence and distribution terms for any publically available version or derivative of this code cannot be changed. i.e. this code cannot simply be copied and put under another distribution licence [including the GNU Public Licence. Samsung Techwin cares for the environment at all product manufacturing stages, and is taking measures to provide customers with more environmentally friendly products. The Eco mark represents Samsung Techwin’s devotion to creating environmentally friendly products, and indicates that the product satisfies the EU RoHS Directive. Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal. SALES NETWORK SAMSUNG TECHWIN CO., LTD. Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400 TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745 SAMSUNG TECHWIN AMERICA Inc. 1480 Charles Willard St, Carson, CA 90746, UNITED STATES Tol Free : +1-877-213-1222 FAX : +1-310-632-2195 www.samsungcctvusa.com www.samsungtechwin.com www.samsungsecurity.com www.samsungipolis.com SAMSUNG TECHWIN EUROPE LTD. Samsung House, 1000 Hillswood Drive, Hillswood Business Park Chertsey, Surrey, UNITED KINGDOM KT16 OPS TEL : +44-1932-45-5300 FAX : +44-1932-45-5325 ">
Advertisement
Key Features
- Indoor & outdoor IP security camera
- CCD 25.4 / 3 mm (1 / 3") 704 x 576 pixels
- Wired Ethernet LAN
- Night vision IR
- Optical zoom: 3.9x Digital zoom: 16x
- Dome Ceiling
- White
- 650 g
