Premier Mounts | P4263FP | Specifications | Premier P4263FP flat panel wall mount

Premier P4263FP flat panel wall mount
P4263FP
Portrait Flat Mount for 42″ to 63″ Flat-Panels
INSTALLATION INSTRUCTIONS
CREATING POSITIVE CUSTOMER EXPERIENCES
9531-210-011-01
P4263FP
Contents
Weight Limit................................................................................................................................................................................... 2
Warning Statements...................................................................................................................................................................... 2
Installation Tools............................................................................................................................................................................ 3
Parts List....................................................................................................................................................................................... 3
Mounting Hardware....................................................................................................................................................................... 4
Features........................................................................................................................................................................................ 5
Installing the Wall Plate................................................................................................................................................................. 6
Introduction..................................................................................................................................................................... 6
Determining the Mounting Surface................................................................................................................................. 6
Wood Stud Installation.................................................................................................................................................... 6
Concrete Installation....................................................................................................................................................... 8
Steel Stud Installation..................................................................................................................................................... 9
Installing the Mounting Bracket....................................................................................................................................................11
Selecting the Mounting Hardware..................................................................................................................................11
Universal Washer Installation........................................................................................................................................ 12
Universal Spacer Installation........................................................................................................................................ 12
Locking and Leveling Screw Installation....................................................................................................................... 13
Lock-It™ Security Barrel Installation (Optional).......................................................................................................................... 14
Attaching the Mounting Bracket to the Flat Panel......................................................................................................... 14
Attaching the Flat Panel to the Wall Plate..................................................................................................................... 15
Mounting Bracket Adjustments.................................................................................................................................................... 15
Leveling Screw Adjustment........................................................................................................................................... 15
Locking Screw Adjustment............................................................................................................................................ 15
Utilizing the Security Barrel........................................................................................................................................... 16
Technical Specifications.............................................................................................................................................................. 16
Warranty...................................................................................................................................................................................... 17
Disclaimer.................................................................................................................................................................................... 17
Weight Limit
Maximum Flat Panel Weight:
175 lbs.
THE WALL STRUCTURE MUST BE CAPABLE OF
SUPPORTING AT LEAST FIVE TIMES THE WEIGHT OF
THE FLAT PANEL. IF NOT, THE WALL STRUCTURE MUST
BE REINFORCED.
Warning Statements
PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS MUST BE READ AND
COMPLETELY UNDERSTOOD. KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION
FOR FUTURE REFERENCE.
PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN MUST BE FOLLOWED, AS OUTLINED
IN THESE INSTALLATION INSTRUCTIONS. FAILURE TO DO SO COULD RESULT IN PROPERTY DAMAGE, SERIOUS
PERSONAL INJURY, OR EVEN DEATH.
SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT. USE
PROPER SAFETY EQUIPMENT AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY.
PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS
PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY
UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS, AND IS NOT RESPONSIBLE FOR ANY DAMAGES, CLAIMS,
DEMANDS, SUITS, ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM, ARISING OUT OF OR
IN ANY MANNER RELATING TO ANY SUCH USE, ATTACHMENTS OR MODIFICATIONS.
At least two qualified people should perform the assembly procedure. Personal injury and/or property damage can result
from dropping or mishandling the flat panel.
If mounting to wall studs or ceiling studs, make sure that the mounting screws are anchored into the center of the wall studs
or ceiling studs. Use of an edge-to-edge stud finder is recommended.
It is recommended that a maximum of ⅝″ plaster board be used when mounting to wooden studs.
Be aware of the mounting environment. If drilling and/or cutting into the mounting surface, always make sure that there
are no electrical wires in wall. Cutting or drilling into an electrical line may cause serious personal injury.
Make sure there are no water or natural gas lines inside the wall where the mount is to be located. Cutting or drilling into a
water or gas line may cause severe property damage or personal injury.
This product is intended for indoor use only. Use of this product outdoors could lead to product failure and/or serious
personal injury.
Do not install near sources of high heat. Do not install on a structure that is prone to vibration, movement or chance of
impact.
Contact Premier Mounts with any questions:
(800) 368-9700
techsupport@mounts.com
Page 2
Visit the Premier Mounts website at http://www.premiermounts.com
Installation Instructions
P4263FP
Installation Tools
The following tools may be required, dependent upon your particular installation. These tools are not provided by
Premier Mounts, but you can purchase them at your local hardware store.
Electronic Stud Finder
¼˝ Drill Bit for
Wood Stud
7/16˝
Drill Bit for
Steel Stud*
/16˝ Concrete Drill Bit**
Hand Held Drill
5
2
1
Pencil
Level
Protective Eyewear
Socket Wrench
Tape Measure
½″ Socket
Hammer**
Phillips Tip Screwdriver
M10 Socket*
* Optional tools for steel stud installations.
** Optional tools for concrete installations.
Parts List
Your Premier Mounts product is shipped with all proper installation hardware and components. Make sure that none
of these parts are missing and/or damaged before beginning installation. If there are parts missing and/or damaged,
please stop the installation and contact Premier Mounts at (800) 368-9700.
P4263FP Universal Low Profile Flat Mount Assembly Components
5/16″ Flat Washers
(Qty 6)
M6 x 250mm Screws
(Qty 4)
Wall Plate
(Qty 1)
Mounting Brackets
(Qty 2)
Universal Spacers
(Qty 24)
Security Barrel
(Qty 1)
Thread Depth Indicator
(Qty 1)
Universal Washers
(Qty 6)
Pro Mounting Hardware
M6 Steel Stud Anchors
(Qty 6)
Installation Instructions
5/16″ Concrete Wedge Anchors
(Qty 6)
Visit the Premier Mounts website at http://www.premiermounts.com
5/16″ x 3″ Lag Bolts
(Qty 6)
Page 3
P4263FP
Parts List (cont’d)
Mounting Hardware
M4 x 16mm Screw
(Qty 6)
M8 x 16mm Screw
(Qty 6)
M4 x 25mm Screw
(Qty 6)
M8 x 25mm Screw
(Qty 6)
M4 x 30mm Screw
(Qty 6)
M8 x 30mm Screw
(Qty 6)
M5 x 16mm Screw
(Qty 6)
M8 x 45mm Screw
(Qty 6)
M5 x 25mm Screw
(Qty 6)
M8 x 70mm Screw
(Qty 4)
M5 x 30mm Screw
(Qty 6)
M6 x 16mm Screw
(Qty 6)
M6 x 25mm Screw
(Qty 6)
M6 x 30mm Screw
(Qty 6)
M6 x 45mm Screw
(Qty 6)
Page 4
Visit the Premier Mounts website at http://www.premiermounts.com
Installation Instructions
P4263FP
Features
Leveling Screws
Allows for leveling
adjustments of the flat panel
after mounting.
Cable/Electrical Cut Out
A large cut out on the wall
plate allows for easy cable
access and power
distribution installations.
Directional Mounting Arrow
Directional Mounting Arrow
lets you know which edge is
up.
Low Profile Design
Holds the flat panel
less than 1″ from
the wall.
Mounting Slots
Allow for a variety of stud
configurations and lateral
shift adjustments when
mounting your flat panel.
Locking Safety Screws
Prevents the flat panel from
being removed or dislodged
from the wall plate.
Installation Instructions
Visit the Premier Mounts website at http://www.premiermounts.com
Universal Spacers
Premier Mount’s uniquely
designed spacers that fit
multiple screw sizes.
Page 5
P4263FP
Installing the Wall Plate
Introduction
Directional Mounting Arrow
The Directional Mounting Arrow stamped into the
top of the P4263FP wall mount indicates which
edge is the top.
Mounting Safety
Two people are recommended to for the
installation of this mount.
Determining the Mounting Surface
If you will be installing your P4263FP mount to wood
studs, proceed to the “Wood Stud Installation”
section.
If you will be installing your P4263FP mount to a
concrete wall, proceed to the “Concrete Installation”
section.
Wo
od
Stu
d
Co
ncr
ete
Ste
el S
tud
If you will be installing your P4263FP mount to a
steel frame, proceed to the “Steel Stud Installation”
section.
Wood Stud Installation
Step 1
You must secure the wall plate to two (2) wall
studs with a minimum of four (4) lag bolts (2 lag
bolts for each stud found).
X
X
➊➊ Use a stud finder to determine the exact center of
➋➋
wall studs in the vicinity of the wall plate.
Use a pencil to mark the exact center of each of the
wall studs.
Step 2
Two people are recommended for this step; one
person to level the wall plate and another person
to mark the wall stud location.
➊➊ Place the wall plate against the wall in the desired
➋➋
➌➌
➍➍
viewing location.
Adjust the wall plate to align the mount slots in the
wall plate with the center of the wall studs.
Level the wall plate.
Use a pencil to mark the upper right mounting
location along the center of the wall stud.
Page 6
Visit the Premier Mounts website at http://www.premiermounts.com
Installation Instructions
P4263FP
Installing the Wall Plate (cont’d)
Step 3
Drill a “pilot hole” in the center of the upper right mark
using a ¼″ drill bit and power drill.
Only use a ¼″ drill bit when drilling the pilot holes.
Step 4
➊➊ Place the wall plate against the wall and align it with
➋➋
the pilot hole.
Insert one (1) 5/16″ x 3″ lag bolt and one (1) 5/16″
washer into the upper right mounting hole and
tighten using a socket wrench and ½″ socket.
Do not overtighten the lag bolt.
Step 5
➊➊ Level the wall plate.
➋➋ Use a pencil to mark the remaining three (3)
mounting locations along the center of each wall
stud.
Step 6
Two people are recommended for this step; one
person to level the wall plate and another person
to drill the pilot holes.
Drill a “pilot hole” in the center of each of the marks with
a power drill and a ¼″ drill bit.
Only use ¼″ drill bit when drilling the pilot holes.
Installation Instructions
Visit the Premier Mounts website at http://www.premiermounts.com
Page 7
P4263FP
Installing the Wall Plate (cont’d)
Step 7
➊➊ Insert one (1)
➋➋
/16″ x 3″ lag bolt and one (1) 5/16″ washer
into each pilot hole
Tighten all lag bolts using a socket wrench and ½″
socket.
5
Do not overtighten the lag bolts when attaching the
mount to the wall. Improper installation may result in
personal injury or property damage.
Proceed to the “Installing the Mounting Bracket”
section.
Concrete Installation
The supplied 5/16″ concrete wedge anchors must be
used for concrete installation.
You will need a 5/16″ concrete drill bit, which is
available at your closest hardware store.
Concrete Wedge Anchors
Example of 5/16″ Concrete Drill Bit (Not Included)
Step 1
Two people are recommended for this step; one
person to level the wall plate and another person
to mark the mounting locations.
>1
2”
➊➊ Place the wall plate against the wall in the desired
➋➋
➌➌
➍➍
viewing location.
Level the wall plate.
Use a pencil and mark 2 upper and 2 lower
mounting locations where you will be drilling holes
for the concrete wedge anchors. Each horizontal
location cannot be closer than 12″ apart.
Set the wall plate to one side in a safe location.
Step 2
Use a power drill and 5/16″ masonry drill bit to drill a hole
at each of the marks.
Page 8
Visit the Premier Mounts website at http://www.premiermounts.com
Installation Instructions
P4263FP
Installing the Wall Plate (cont’d)
Step 3
➊➊ Insert a concrete wedge anchor into each hole.
➋➋
➌➌
If necessary, lightly tap each concrete wedge anchor
into place with a hammer.
Remove the nuts and washers from all four (4)
concrete wedge anchors.
Replace the washers which you removed from
the concrete wedge anchors with the 5/16″ washers
shown in the parts list on Page 3.
Step 4
➊➊ Place the wall plate against the wall over the
➋➋
threaded shafts of the concrete wedge anchors.
Attach the nuts and 5/16″ washers to each of the
concrete wedge anchors and tighten using a socket
wrench and an M10 socket.
Do not overtighten the wedge anchor nuts.
Proceed to the “Installing the Mounting Bracket”
section.
Steel Stud Installation
The supplied M6 steel stud anchors must be used
to install your Premier Mounts’ mount to steel
studs. Do not use lag bolts or wood screws.
Steel Stud Anchor Screw
Steel Stud Anchor Sleeve
Step 1
➊➊ Identify the general location on the wall where you
will be mounting your flat panel.
➋➋ Use a stud finder to determine the exact center
➌➌
of each steel stud in the vicinity of the mounting
location.
Use a pencil and mark the exact center of each
steel stud.
Installation Instructions
Visit the Premier Mounts website at http://www.premiermounts.com
X
Page 9
Installing the Wall Plate (cont’d)
P4263FP
Step 2
➊➊ Place the wall plate against the wall in the desired
➋➋
➍➍
➎➎
➏➏
viewing location.
Adjust the wall plate to match the locations of the
steel studs.
Level the wall plate.
Use a pencil and mark 2 upper and 2 lower
locations where you will be drilling holes for the steel
stud anchors.
Set the wall plate to one side in a safe location.
Step 3
➊➊ Use a power drill and
➋➋
7
/16″ drill bit to drill a hole at
each of the marks.
Insert a steel stud anchor into each hole.
If necessary, lightly tap each steel stud anchor into
place with a hammer.
Step 4
Use a Phillips screwdriver to tighten each steel
stud anchor screw until the legs have completely
compressed against the back of the steel stud.
The steel stud anchor screw will feel tight when
you first begin to turn it until the legs begin to
compress. The steel stud anchor screw will then
turn easier for several turns. The steel stud anchor
screw will again feel tight when the legs have
completely compressed against the back of the
drywall. Stop turning the steel stud anchor screw
at that point.
Do not overtighten the steel stud anchor screw.
Remove the steel stud anchor screws and set them
aside.
Steel stud anchors may come with small paper
washers. You may leave them on the screw or
discard them. These small paper washers do not
replace standard 5/16″ washers.
Page 10
Visit the Premier Mounts website at http://www.premiermounts.com
Installation Instructions
P4263FP
Installing the Wall Plate (cont’d)
Step 5
➊➊ Align the wall plate over the steel stud anchor sleeves.
➋➋ Insert a steel stud anchor screw and a / ″ washer into
5
➌➌
16
each steel stud anchor sleeve.
Use a Phillips screwdriver and tighten each steel stud
anchor screw until it is just snug.
Do not overtighten the steel stud anchor screws.
Do not use a power drill to tighten the steel stud anchor
screws.
Proceed to the “Installing the Mounting Bracket”
section.
Installing the Mounting Bracket
Selecting the Mounting Hardware
➊➊ Insert a small straw or toothpick into the threaded
inserts found on the back of the flat panel.
➋➋ Use a pencil to mark the depth of the threaded
➌➌
➍➍
➎➎
insert on the small straw or toothpick.
Mark the straw or toothpick 1/8” above the depth of
the threaded insert, as shown in Figure 1.
Insert the small straw or toothpick into the remaining
threaded inserts to compare and verify their depth
using the straw or toothpick’s 1/8” allowance mark.
Locate the correct diameter screw for the threaded
insert.
If the screw you selected is longer than the 1/8”
allowance mark on the small straw or toothpick,
as shown in Figure 2 and Figure 3, do not use
this screw. The screw length must not bypass the
mark.
Marking the 1/8”
Allowance
➏➏ Test each size of the screws provided.
Small Straw or Toothpick
The correct screws should thread easily into the
mounting point and not pull out when tension is
applied.
Proceed to the “Universal Washer Installation”
section.
Installation Instructions
Small Straw
or Toothpick
Depth Plus 1/8” Allowance
Mark
Visit the Premier Mounts website at http://www.premiermounts.com
Small Straw
or Toothpick
Depth Plus 1/8” Allowance
Mark
Page 11
P4263FP
Installing the Mounting Bracket (cont’d)
Universal Washer Installation
Premier Mounts’ Universal Washers are designed to
accommodate the various M4, M5, M6 and M8 hole
sizes required by flat panels.
Do not place excessive pressure on the back of
the flat panel, as this may damage your flat panel.
The Universal Washer must be installed between
the head of the mounting screw and the mounting
bracket as shown.
Does your flat panel have:
●● Recessed mount points?
●● Uneven mount points?
●● A curved back?
●● Any obstruction near the mount point?
If Yes, you must install Universal Spacers. Proceed to
the “Universal Spacer Installation” section.
Mounting Screw
If No, skip to the “Lock-It™ Security Barrel
Installation (Optional)” section.
Universal Washer
Mounting Bracket
Universal Spacer Installation
Premier Mounts’ Universal Spacers allow you to
attach the mounting bracket to flat panels which have
recessed or uneven mount points. Each Universal
Spacer adds ¼˝ to the distance between the mounting
bracket and your flat panel.
Flat Panel
Universal Spacer
Mount Point
The Universal Spacers must be stacked and
oriented as shown.
The Universal Spacers must only be installed
between the mounting bracket and your flat panel.
The Universal Spacers will fit M4, M5, M6 and M8
screw sizes.
Proceed to the “Locking and Leveling Screw
Installation” section.
1˝
Page 12
¼˝
Visit the Premier Mounts website at http://www.premiermounts.com
Installation Instructions
P4263FP
Installing the Mounting Bracket (cont’d)
Locking and Leveling Screw Installation
Leveling Screw Installation
You must install the leveling screws before you
attach the mounting bracket to the back of the flat
panel. The leveling screws consists of two (2) M6
x 250mm screws.
Thread one (1) leveling screw into the top mounting
hole on each of the mounting brackets. Make sure the
leveling screw is securely threaded into the mounting
tab before proceeding.
Do not thread the leveling screw any further once
it is even with the mounting tab. Threading the
leveling screw any further will prevent you from
safely attaching the flat panel to the wall plate.
Leveling Screw
Correctly Threaded
Leveling Screw
Threaded Too Far
Locking Screw Installation
You must install the locking screws before you
attach the mounting bracket to the back of the flat
panel. The locking screws consists of two (2) M6 x
250mm screws.
Thread one (1) locking screw into the bottom mounting
hole on each of the mounting brackets. Make sure the
locking screw is securely threaded into the mounting tab
before proceeding.
Do not thread the locking screw any further once
it is even with the mounting tab. Threading the
locking screw any further will prevent you from
safely attaching the flat panel to the wall plate.
Locking Screw
Correctly Threaded
Proceed to the “Lock-It™ Security Barrel
Installation (Optional)” section.
Installation Instructions
Visit the Premier Mounts website at http://www.premiermounts.com
Locking Screw
Threaded Too Far
Page 13
P4263FP
Lock-It™ Security Barrel Installation (Optional)
Optional security configurations include:
- PCB-CSL1 (sold separately)
- Padlock (Combination or Keyed; commercially
available)
Mounting Tab
Please read the following directions to install the
security barrel:
the locking screw from the mounting
➊➊ Remove
bracket.
the locking screw into and through the
➋➋ Place
security barrel (see illustration below).
the locking screw and security barrel into
➌➌ Re-insert
the mounting bracket.
the locking screw and security barrel until
➍➍ Tighten
seated in the mounting tab.
Do not thread the locking screw any further once
it is even with the mounting tab (see illustration to
the right). Threading the locking screw any further
will prevent you from safely attaching the flat
panel to the wall plate.
Do not overtighten the locking screw.
Proceed to the “Attaching the Mounting Bracket to
the Flat Panel” section.
Locking Screw
Lock-It™ Security
Barrel
Attaching the Mounting Bracket to the Flat Panel
This section presumes that you have read and
understood these sections:
●● Selecting the Proper Mounting Hardware
●● Universal Washer Installation
●● Universal Spacer Installation
➊➊ Place your flat panel screen-side down on a soft, flat
➋➋
➌➌
➍➍
surface.
Identify the number and location of the thread
inserts on the back of your flat panel.
Aligning the holes on each mounting bracket with
the thread inserts on the back of your flat panel.
Secure each mounting bracket to your flat panel by
inserting a minimum of two (2) screws per bracket.
Do not overtighten the mounting hardware.
Proceed to the “Attaching the Flat Panel to the Wall
Plate” section.
Page 14
Visit the Premier Mounts website at http://www.premiermounts.com
Installation Instructions
P4263FP
Installing the Mounting Bracket (cont’d)
Attaching the Flat Panel to the Wall Plate
This section requires two people.
Do not release your flat panel until you are certain that top and bottom hooks of both mounting brackets are
securely seated on the upper and lower mounting rails of the wall panel.
➊➊ Raise the flat panel past the top and bottom mounting rails on the wall panel.
➋➋ Slide the flat panel down slowly, keeping it close to the wall.
➌➌ Engage the top and bottom mounting brackets to the rails of the wall plate.
Proceed to the “Mounting Bracket Adjustments” section.
Mounting Bracket Adjustments
Leveling Screw Adjustment
If your flat panel is tilted too far to one side, the leveling
screws will allow you compensate for this tilt by simply
adjusting the screws with a screwdriver.
➊➊ Loosen both locking screws.
➋➋ Adjust the tilt of your flat panel.
➌➌ Tighten both locking screws.
M6 x 250mm
Leveling Screw
(1 per Bracket)
Caution!
It is possible to dislodge your flat panel while you
level your flat panel. Use extreme caution until
you tighten the locking screws.
Locking Screw Adjustment
After you have finished leveling your flat panel, be sure
to tighten the two (2) M6 x 250mm locking screws.
Do not overtighten the locking screws.
M6 x 250mm
Locking Screw
(1 per Bracket)
Installation Instructions
Visit the Premier Mounts website at http://www.premiermounts.com
Page 15
P4263FP
Utilizing the Security Barrel
Your P4263FP Mount includes one (1) Security Barrel
which can provide additional theft deterrence for your
flat panel.
PCB-CSL1 Security Cable Thread the cable through the hole on the security
barrel.
Attach the PCB-CSL1 locking mechansim and
secure it using the supplied key.
Padlock Place the locking hook through the hole of the
security barrel.
Snap lock and locking hook together.
Padlock
(Combination or Keyed)
PCB-CSL1
Technical Specifications
All measurements are in inches [millimeters].
562.85
22.159
530.28
20.877
501.70
19.752
742.14
29.218
Page 16
707.78
27.866
142.60
5.614
24.37
.960
287.93
11.336
Visit the Premier Mounts website at http://www.premiermounts.com
Installation Instructions
P4263FP
Warranty
PREMIER MOUNTS
LIMITED LIFETIME WARRANTY
What and Who is Covered by this Limited Warranty and for How Long
Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original
owner of this product. The limited warranty is valid only for the original purchaser of the product.
What Premier Mounts Will Do
At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is defective.
If Premier Mounts chooses to replace a defective product or part, a replacement product or part will be shipped to you
at no charge, but you must pay any labor costs.
What is Not Covered; Limitations
PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS, ADAPTERS, DISPLAYS,
PROJECTORS, OTHER PROPERTY, OR PERSONAL INJURY RESULTING, IN WHOLE OR IN PART, FROM
IMPROPER INSTALLATION, MODIFICATION, USE OR MISUSE OF ITS PRODUCTS.
PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. PREMIER MOUNTS IS NOT
RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO,
INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE
PRODUCTS OR PARTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
What Customers Must Do for Limited Warranty Service
If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the address
below within thirty (30) days. Proof of purchase (an original sales receipt) from the original consumer purchaser must
accompany all warranty claims. Warranty claims must also include a description of the problem, the purchaser’s name,
address, and telephone number. General inquiries can be addressed to Premier Mounts Customer Service at 1-800368-9700. Warranty claims will not be accepted over the phone or by fax.
Premier Mounts
Attn: Warranty Claim
3130 East Miraloma Ave.
Anaheim, CA 92806
How State Law Applies
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH
VARY FROM STATE TO STATE.
Disclaimer
Premier Mounts intends to make this manual accurate and complete. However, Premier Mounts makes no claim that
the information contained herein covers all details, conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this product. The information contained in this document
is subject to change without notice or obligation of any kind. Premier Mounts makes no representation of warranty,
expressed or implied, regarding the information contained herein. Premier Mounts assumes no responsibility for
accuracy, completeness or sufficiency of the information contained in this document.
Contact Us
NORTH AMERICA
3130 East Miraloma Avenue
Anaheim, CA 92806 USA
USA and Canada
Phone: 1-800-368-9700
Fax: 1-800-832-4888
Other Locations
Phone: (001) 714-632-7100
Fax: (001) 714-632-1044
EUROPE
Unit 3, The Moorings Business Park,
Channel Way, Longford,
Coventry, CV6 6RH, UK
Phone: +44 (0) 24 7664 4105
Fax: +44 (0) 24 7664 4165
©Premier Mounts 2011
Installation Instructions
Visit the Premier Mounts website at http://www.premiermounts.com
Page 17
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising