Avent SCD610/01 User manual User manual

Register your product and get support at
www.philips.com/welcome
User manual
SCD610
SCD609
Contents
1 Introduction
2 Important Safety Instructions
Compliance information
Recycling
4
6
8
9
3 Overview
10
Parent unit
Baby unit
10
11
4 Get started
Charge the parent unit
Set up the baby unit
Wall mount the baby unit
5 Use your baby monitor
Operating range
6 Menu
Zoom & Pan
Voice activation
Adjust brightness
Add/delete cameras
Change the language
Reset
7 Optimize the battery life of the
parent unit
8 Guarantee and service
Warranty
9 Frequently asked questions
12
12
13
13
15
15
16
16
16
16
16
17
18
19
19
19
20
EN
3
1 Introduction
SCD609
Baby unit
Congratulations on your purchase and welcome
support that Philips AVENT offers, register your
product at www.philips.com/AVENT.
Philips AVENT is dedicated to producing caring
and reliable products that give parents the
reassurance that they need. This Philips AVENT
baby monitor provides round-the-clock support
by ensuring that you can see and hear your
baby in perfect clarity.
The instructions are intended for both SCD610
and SCD609.
SCD610
Know these
safetysymbols
CAUTION
Parent unit
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Baby unit
4
EN
This “bolt of lightning” indicates uninsulated material within your unit may
cause an electrical shock. For the safety of
everyone in your household, please do not
remove product covering.
The “exclamation point” calls attention to features for which you should
read the enclosed literature closely to prevent operating and maintenance problems.
WARNING: To reduce the risk of fire or
electric shock, this apparatus should not be
exposed to rain or moisture and objects
filled with liquids, such as vases, should not
be placed on this apparatus.
CAUTION: To prevent electric shock,
match wide blade of plug to wide slot, fully
insert.
EN
5
2 Important Safety
Instructions
a Read these instructions.
b Keep these instructions.
c Heed all warnings.
d Follow all instructions.
e Do not use this apparatus near water.
f Do not install near any heat sources
such as radiators, heat registers, stoves
that produce heat.
g Where the power plug is used as the
disconnect device, the disconnect device
shall remain readily operable.
h Protect the adapter cord from being
walked on or pinched particularly at
plugs, convenience receptacles, and
the point where they exit from the
apparatus.
i Only use attachments/accessories
j Use this apparatus only for its intended
use as described in this manual.
k Do not overload wall outlets and
extension cords as this can result in the
l Never push objects of any kind into this
apparatus through casing slots as they
may touch dangerous voltage points or
short out parts that could result in a risk
m The apparatus shall not be exposed to
dripping or splashing and no objects
placed on the apparatus.
n Do not place any sources of danger on
6
EN
!
o "
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus,
the apparatus has been exposed to rain
or moisture, does not operate normally,
or has been dropped. For assistance,
visit our website www.philips.com/
AVENT or call 1-800-54-AVENT
#$%%&'($)*$
p This product may contain lead and
mercury. Disposal of these materials
may be regulated due to environmental
considerations. For disposal or recycling
information, please contact your local
authorities or the Electronic Industries
Alliance: www.eiae.org.
Warning
To prevent strangulation with the power cord, always
keep the baby unit and the power cord out of baby's
reach, at least 1 meter/3.5 feet away. Do not use
extension cords.
Caution: Risk of explosion, electric shock,
short circuit, or leakage
The apparatus shall not be exposed to
with liquids, such as vases, shall not be
placed on the apparatus.
Before you connect the baby monitor
to the mains, make sure that the voltage
indicated on the adapters of the baby
monitor corresponds to the local mains
voltage.
Where the MAINS plug is used as the
disconnect device, the disconnect device
shall remain readily operable.
Use the supplied adapter to connect the
baby unit to the mains.
Use the supplied adapter to charge the
parent unit.
To prevent electric shock, do not open
the housing of the baby unit or parent unit
except for the battery compartments.
Make sure that your hands are dry when
you insert or replace batteries (battery
pack).
For the parent unit, use only the
rechargeable battery pack supplied with
the baby monitor. Charge the rechargeable
battery pack as described in this user
manual.
To avoid a risk of explosion, replace the
battery with a correct type.
Dispose of used batteries according to
instructions.
To prevent battery explosion or leakage,
which can damage the baby monitor and
cause burns and skin or eye irritation:
do not recharge non-rechargeable
batteries,
insert batteries in the right direction
(+/-),
remove batteries if you are not going to
use the product for more than 30 days,
keep the battery away from excessive
!"!
To prevent the battery from heating up or
releasing toxic materials, hydrogen, or oxygen,
do not:
overcharge,
short circuit,
reverse charge, or
mutilate batteries.
To handle damaged or leaked batteries, wear
protective gloves to protect your skin.
Adult supervision
This baby monitor is intended as an aid. It is
not a substitute for responsible and proper
adult supervision and should not be used as
such.
Never place the baby unit inside the baby
bed or playpen.
To prevent overheating, do not cover the
baby monitor with a towel, blanket, or any
other items.
When your baby monitor uses a power
outlet, make sure that you can easily access
the power outlet.
For their safety, do not allow children to play
with the baby monitor.
Cleaning and Maintenance
Do not immerse the parent unit or baby
unit in water, and do not clean them
under the tap.
Do not use cleaning spray or liquid
cleaners.
Unplug the parent unit and baby unit if
they are connected to a power outlet.
Clean the parent unit and baby unit with
a damp cloth.
Clean the adapters with a dry cloth.
This baby monitor has no other
userserviceable parts.
Storage precautions
Use and store the baby monitor between
10°C (50°F) and 35°C (95°F). Keep the baby
monitor out of direct sunlight.
Disposal
Dispose of batteries properly. Do not
incinerate. Batteries may explode if
overheated. Do not wrap in metal or
aluminum foil. Wrap in newspaper before
discarding.
It is suggested that you contact your local
town or city to determine proper battery
redemption site(s) in your area.
Please visit www.recycle.philips.com for
additional information on a recycling
center in your area.
Replacement
If you need to replace the adapters, use the
#
If you need to replace the battery, please
contact the customer care center.
EN
7
Compliance information
The FCC ID number is located on the casing
bottom of the parent unit and in the battery
compartment of the baby unit.
$%*;
%
*
<#
means that the equipment meets certain
radio communications and operational
requirements. This device complies with
Part 15 of the FCC Rules and RSS-210 of
Industry Canada. Operation is subject to the
following two conditions: (1) this device may
not cause harmful interference, and (2) this
device must accept any interference received,
including interference that may cause undesired
operation.
Radio interference
This equipment has been tested and found
to comply with the limits for a Class B digital
device,pursuant to Part 15 of the FCC Rules
and ICES-003 of Industry Canada. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses
and can radiate radio frequency energy and, if
not installed and used in accordance with the
instructions, may cause harmful interference
to radio communications.However, there is
no guarantee that interference will not occur
in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference
by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the
equipment and receiver.
-- Connect the equipment to an outlet on a
circuit different from that to which the receiver is
connected.
RF Radiation Exposure Statement
8
EN
This equipment complies with FCC RF radiation
exposure limits set forth for an uncontrolled
environment. This equipment should be installed
and operated with a minimum distance of 7 3/4
inches / 20 centimeters between the radiator
and your body. For handheld operation, this
equipment has been tested and meets the
FCC RF exposure guidelines. For body-worn
operation,this product has been tested and
meets the FCC RF exposure guideline when
used with the belt clip supplied with this
product. This transmitter must not be co-located
or operating in conjunction with any other
antenna or transmitter. Use of other accessories
may not ensure compliance with FCC RF
exposure guidelines.This equipment also complies
with Industry Canada RSS-102 with respect
to Canada’s Health Code 6 for Exposure of
Humans to RF Fields.
Do not attempt to repair or modify this
equipment
Any repairs or alterations made by the user
to the equipment may void the warranty
and compliance of the equipment. Changes
=
not expressly approved by Philips AVENT
may void the FCC authorization to operate
this equipment. For assistance visit our
website www.philips.com/AVENT or call
1-800-54-AVENT (1-800-542-8368).
Do not attempt to repair or modify this
equipment
Any repairs or alterations made by the user
to the equipment may void the warranty
and compliance of the equipment. Changes
=
not expressly approved by Philips AVENT
may void the FCC authorization to operate
this equipment. For assistance visit our
website www.philips.com/AVENT or call
1-800-54-AVENT (1-800-542-8368).
>?@G
This Philips AVENT appliance complies with all
>?@G#%
handled properly and according to the instructions
in this user manual, the appliance is safe to use
JJ#
Recycling
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
When you see the crossed-out wheel bin
symbol attached to a product, it means the
product is covered by the European Directive
2002/96/EC:
Never dispose of your product with other
household waste. Please inform yourself about the
local rules on the separate collection of electrical
and electronic products.The correct disposal
of your old product helps prevent potentially
negative consequences on the environment and
human health.
Your product contains batteries covered by the
European Directive 2006/66/EC, which cannot be
disposed of with normal household waste.
When you see the crossed-out wheel bin symbol
with the chemical symbol 'Pb', it means that the
batteries comply with the requirement set by the
directive for lead:
Please inform yourself about the local rules on
separate collection of batteries. The correct
disposal of batteries helps prevent potentially
negative consequences on the environment and
human health.
EN
9
Solid green: The unit is running.
3 Overview
f Voice activation light
g Sound level lights
Indicate the level of sound in your
baby's room
Parent unit
l
a
k
b
c
j
i
h
d
e
f
g
a
ON/OFF switch
Press and hold to turn the parent unit
on or off
b Stand
c Voice activation button
Press and hold to turn voice activation
on or off
For details, please refer to Page 16.
d Connector for the supplied DC adapter
e Power on/off light
Flashing red: The rechargeable battery
is low in power.
Flashing green: The rechargeable
battery is in charging mode.
10
EN
h Key
+ [UP]
- [DOWN]
[LEFT]
[RIGHT]
i
Menu
j Speaker
k Video display
Signal strength indicator
Battery power indicator
Low battery power indicator
l Antenna
Connector for the supplied AC/DC adapter
Input: 100-240V AC
Output: 6.0V DC, 500 mA
Model number: For UK, SSW1920UK-2; For the other European
countries, SSW-1920EU-2
For US and Canada, SSW-1920US-2
For Australia and New Zealand, SSW1920AU-2
For Mexico, SSW-1920MX-2
f Lens
Baby unit
g Connector for the supplied DC adapter
h Wall mount
a
b
f
c
d
g
e
i Wall mount screws
Connector for the supplied AC/DC adapter
Input: 100-240V AC
Output: 6.0V DC, 500 mA
Model number: For UK, SSW1920UK-2; For the other European
countries, SSW-1920EU-2
For US and Canada, SSW-1920US-2
For Australia and New Zealand, SSW1920AU-2
For Mexico, SSW-1920MX-2
h
i
a Antenna
b Power-on light
In green: The baby unit is turned on
c
ON/OFF switch
Press and hold to turn the baby unit
on or off
Short press to pair the parent unit
while the baby unit is on.
d Microphone
e Stand
EN
11
4 Get started
2
Insert the rechargeable battery.
3
4
Reattach the lid.
Charge the parent unit
Note
Make sure your hands and the unit are dry when you
insert and remove the rechargeable battery.
Do as follows to charge the parent unit before
<
unit indicates that the battery is low.
» ^
the video display and the battery on/
^
#
Insert the plug into parent unit and put the
adapter in a wall socket.
Note
If the battery is completely empty, the parent unit
automatically switches off.
The batter Model No. is BL-5C, 1050mAh.
1
To remove the battery door, slide to the
right.
» The battery on/off light on the parent
^
#
» When the battery is fully charged, the
battery light turns solid green.
Note
_
12
EN
after a long time not being used, switch it off and let it
charge continuously for at least 8 hours.
_
time, the operating time is less than 7 hours. The
rechargeable battery only reaches its full capacity after
you have charged and discharged it three times.
The battery gradually discharges, even when the parent
unit is switched off.
Tip
4
Insert the plug into the baby unit and put
the adapter in a wall socket.
5
Place the parent unit within the operation
range of the baby unit. Make sure it is at
least 1.5 metre/5 feet away from the baby
unit to avoid acoustic feedback.
6
For more information on the operating
range, see section "Operating range" below.
Charging normally takes 5 hours, but it takes longer
when the parent unit is switched on during charging. To
keep the charging time as short as possible, switch off
the parent unit during charging.
When the battery is fully charged, the parent unit can
be used cordlessly for approximately 7 hours if it is in
voice activation mode. If the video is on continuously,
the parent unit can be used cordlessly for approx. 5
hours.
Set up the baby unit
Caution
Keep the baby unit out of the reach of the baby. Never
place the baby unit inside or mount it on the baby's
bed or playpen.
Tip
Note
If you use wireless devices, microwave oven or a DECT-
Position the baby unit at a higher level to get a good
overview of the baby's bed or playpen.
system and you experience interference on either the
parent unit or baby unit, move the parent unit further
away until there is no more interference.
1
Place the baby unit at least 1 meter/3.5
feet away from your baby.
2
Place the baby unit on a stable surface.
You may also mount the baby unit on a
wall mount which is provided. For more
information, please refer to the next
section.
3
Adjust the position of the baby unit in a
way that ensures the best visibility of your
baby.
Wall mount the baby unit
Caution
When the baby unit is wall mounted, manage the
{<!
accessible by the baby.
1
Use the paper template to mark the
positions of the three screws to wall
mount your baby unit.
2
3
Drill holes at the three positions.
Place wall plugs in the wall.
EN
13
4
Screw in the wall-mount.
5
Put the baby unit into the wall-mount.
6
Place the cable into the holder at the wallmount.
7
Adjust the baby unit so that you can get a
best view of your baby.
14
EN
5 Use your baby
monitor
Tip
It takes about 15 seconds to establish the link between
the parent unit and the baby unit.
^
runs out of power.
The battery symbol
To see your baby,
1
Press on the parent/baby unit.
» The parent/baby unit turns on, and all
indicators on the parent/baby unit light
^#
Operating range
The operating range of the baby monitor is
150 metres/490 feet in open air. The range
varies depending on the surroundings and other
disturbing factors.
This monitor is designed to operate at its
best within a 150m range, suitable for most
household environments. The operating range
and quality of the connection varies depending
on the number of obstructions, like walls or
buildings, in between the two units.
» Philips AVENT logo appears on the
^#
» If no link is established, a [NOT
LINKED!CAM1 OUT OF RANGE]
^
#
parent unit beeps from time to time.
Note
The CAM1 refers to the default camera.
EN
15
6 Menu
Press the button on the side of the parent
unit, and the voice activation indicator slowly
blinks.
Change voice activation sensitivity
1
Press menu button on the parent unit.
» Menu is displayed.
2
1
2
Press +/- to move up or down the memu/
submenu, and press / to move left or
right across menu/submenu.
3
4
!
"
To exit, press .
Press menu button on the parent unit.
Select [VOICE ACTIVATION SENSITIVITY]
of the baby unit.
Menu option
[HIGH]
[MID]
[LOW]
Description
High voice activation sensitivity
Medium voice activation
sensitivity
Low voice activation sensitivity
Zoom & Pan
Note
1
2
Press menu button.
Select [ZOOM & PAN] from the menu to
zoom in and out the view, and pan your
view.
Menu option
[ZOOM+]
[PAN]
[ZOOM-]
Description
Zoom in the view
Pan the view to adjust
the focus of the view
Zoom out the view
Voice activation
Voice activation
When the voice activation mode is on, the
video display only switches on when the baby
unit picks up a sound. As long as no sound is
detected, the video display is off to save power.
When you press a key or a sound is detected,
the parent unit is activated, and will be off again
after 20 seconds time-out. The timer is reset
each time when:
A sound exceeds the set voice
activation sensitivity.
One button on parent unit (menu, +, -,
, ) is pressed on.
Turn on voice activation
16
EN
When voice activation is active, the LOOP ALL CAMs
in the switch CAM dialogue is not available.
When the LOOP ALL CAMs is active, the VOICE
ACTIVATION function is not available. An info screen
will be shown when you press the VOX button.
When [VOICE ACTIVATION SENSITIVITY] is
set higher,it picks up a softer sound.
Adjust brightness
1
2
3
Press menu button on the parent unit.
Select [ADJUST BRIGHTNESS].
Press +/- to adjust the brightness of the
video display.
Add/delete cameras
Add a new camera
A maximum of 4 cameras can be paired to a
parent unit. The menu has 4 positions named
CAM1 up to CAM4. Your default setting will be
at CAM1. You can select any of the positions
in the list to assign a camera. It is up to you to
decide which camera is which item in the list.
Note
Only when a position is empty in the list, a new camera
Note
When only one camera is in the paired list, the camera
!##
and
displayed.
can be paired.
1
2
Press menu button on the parent unit.
Select [ADD/DEL CAM].
» The paired CAM list is displayed.
2
Note
A paired CAM cannot be paired again on another
position when it is assigned to a position.
3
4
Select [ADD CAM].
» An info screen will indicate that the
parent unit is searching for the new
camera. You are prompted to shortly
press of the baby unit, with the baby
unit being on.
Short press of the baby unit, less than 1
second.
» <<
pairing process is successful.
Delete a camera
1
From the paired CAM list, select the
camera to be deleted.
» The dialog [DELETE CAM1 FROM
LIST?] is displayed.
2
Press !
press to return.
For example, when "CAM1 DELETE" is
highlighted and selected, CAM1 will be deleted.
Select other cameras
When multiple CAMs are listed in the paired
camera list, you may switch between different
cameras.
1
Press or to show the CAM
<
currently linked to the parent unit.
will not be
Press and to navigate this bar to select
other CAMs in the list, i.e. parent unit tries
to connect to camera.
» Camera icon will change to orange
color when it has been selected.
Loop all cameras
Switch on the tab LOOP ALL cameras to check
what is going on through all paired cameras.
Note
When VOICE ACTIVATION is active, the LOOP ALL
function is not selectable.
When LOOP ALL is activated, will be
in orange color. You will see the views of all
cameras one by one. Other cameras not
viewed will be displayed as the icon , or
(without bracket) etc. It also indicates how
many cameras you have been set up and which
camera will be viewed next.
For example,
1
From
, the view stays at camera one
for 20 seconds.
2
From
, the view stays at camera two
for for 20 seconds.
3
The view switches to another camera if
there is any more camera paired.
Change the language
1
2
Press menu button on the parent unit
select [LANGUAGE]
desired language.
Menu option
GB
FR
Description
English
French
EN
17
Reset
To reset the parent unit:
1
Press and hold
unit.
2
3
Press and hold - on the parent unit.
18
EN
to turn off the parent
When you hold -, turn on the parent unit.
» The parent unit is reset.
7 Optimize the
battery life of
the parent unit
Recharge the parent unit when
you see the low battery icon. Fully
recharge the parent unit before you
use it again, as completely draining the
rechargeable battery may reduce its
life.
Remove the rechargeable battery pack
from the parent unit if you are not
going to use if for a week or longer.
Always fully recharge the parent after a
long period of time.
If you experience any issue while
charging your battery, you may contact
your dealer or a Philips service centre.
8 Guarantee and
service
If you need service or information or if you
have a problem, please visit the Philips AVENT
website at www.philips.com/AVENT welcome
or contact the Philips Consumer Care Centre
#|
of the Philips Consumer Care Centre in the
<<^#%
Philips Consumer Care Centre in your country,
please visit the local Philips dealer.
Warranty
Full two-year warranty
Philips Electronics North America Corporation
(USA) and Philips Electronics Ltd (Canada)
warrant each new Philips AVENT product,
model SCD505/00, against defects in materials
or workmanship for a period of two years from
the date of purchase, and agree to repair or
replace any defective product without charge.
Important: This warranty does not cover
damage resulting from accident, misuse or
!"
!{
any attachment not provided with the product.
No responsibility is assumed for any special,
incidental or consequential damages. In order
to obtain warranty service, simply call toll-free
1-800-54-AVENT.
EN
19
9 Frequently
asked questions
%}
section, you can get support at
www.philips.com/AVENT or contact the Philips
Consumer Care Center in your country.
Problems
My parent/baby unit will not
switch on.
Possible causes
The unit is not connected to the
power supply.
The battery is empty.
My baby unit will not switch on.
The unit is not connected to a
power supply.
The units are out of range.
I cannot establish a connection.
The parent unit beeps and the a
"NOT LINKED! CAMx OUT OF
€
^
#
I get interference. I can only hear
intermittently.
I cannot hear anything through
my parent unit.
My range is less than 150 metres/
490 feet.
20
EN
Solutions
Connect the unit to a power
supply.
Replace the battery and make
sure that it is correctly inserted.
Connect the unit to a power
supply.
Move the units closer (see
"Operating range" )
Parent and baby units are too far Move the parent unit at least
apart.
1.5 metres/ 5 feet away from
the baby unit.
The baby unit is switched off.
Switch on the baby unit.
The units are out of range.
Move the units closer.
The parent unit picks up signals
from other appliances or baby
monitors.
The volume of parent unit is set
too low or it is on mute.
The units are out of range.
You have switched on the
automatic voice activation.
The voice activation sensitivity is
set too low.
Environmental obstructions may
be affecting your range.
Move the parent unit away
from other 2.4GHz wireless
appliances such as telephones.
Increase the volume of the
parent unit.
Move the units closer.
When it is activated, the video
is displayed on when the baby
unit picks up a sound. As long
as no sound is detected, the
video display is off to save
power.
Increase the voice activation
sensitivity.
Move the units closer.
The battery light on the parent
^
#
The battery of the parent unit
runs low quickly.
Is my baby unit secure from
eavesdropping?
I hear other sounds from my
parent unit.
The charging of the parent unit
takes a long time.
The video monitor makes some a
high-pitched noise.
The parent unit makes a buzzing
sound.
J
^"
#
There is no image on the video
display when the power on light
is on.
The image on the video display
is unclear.
The rechargeable battery of the
parent unit is running low.
The volume is set too high and
the unit consumes more power.
The video display is switched
on continuously and the unit
consumes more energy.
Recharge the battery.
The parent unit picks up signals
from other appliances or baby
monitors.
The rechargeable battery of the
parent unit may be low.
The units are nearly out of range.
The parent unit picks up signals
from other appliances or baby
monitors.
The rechargeable battery of the
parent unit may be low.
The parent unit may be in the
automatic voice activation mode.
Move the parent unit away
from other 2.4GHz wireless
appliances such as telephones.
Recharge the battery.
Decrease the volume.
Activate the automatic voice
activation mode to increase the
operating time.
The 2.4GHz digital technology
of this baby monitor guarantees
no eavesdropping.
The baby unit is too far from the Move the baby unit closer to
baby
your baby with a minimum
distance of 1 metre/ 3.5 feet.
The voice activation sensitivity is Decrease the voice activation
set too high.
sensitivity.
The baby unit is close to other
Move the baby unit away from
sound source.
the sound source.
Allow at least 8 hours of
or after a long period of disuse.
charging time.
The parent unit is switched on
Switch off the parent unit
during charging
during charging.
The units may be too close to
Move the parent unit at least
each other.
1.5 metres/ 5 feet away from
the baby unit.
The volume of the parent unit
Decrease the volume of the
may be set too high.
parent unit.
The units are out of range.
Move the units closer.
Move the units closer.
Move the parent unit away
from other 2.4GHz wireless
appliances such as telephones.
Recharge the battery.
Press the automatic voice
activation button again to
switch on the video display.
The display brightness may be set Adjust the display brightness.
too low or too high.
EN
21
The image on the video display is
unclear in night vision.
The parent unit does not charge
when I have plugged it in.
The night vision LED is still ON
when the ambient condition is
bright enough.
The distance between the baby
and the baby unit may be too
long.
The rechargeable battery may
have reached the end of its life.
The baby unit's light sensor
(located on top of the housing
near the antenna) is blocked
from the ambient light.
Tip
Product information is subject to change without prior
notice.
22
EN
Make sure that the baby unit is
placed 1 to 1.5 metres/ 3.5 to
5 feet away from the baby.
Replace the rechargeable
battery.
Relocate the baby unit or leave
it as it is. It will not affect the
picture of the display.
In US manufactured for Philips Consumer Lifestyle,
A division of Philips Electronics North America Corporation,
P.O. Box 10313, Stamford, CT 06904
In Canada imported for Philips Electronics Ltd,
281 Hillmount Road, Markham, ON L6C2S3
Call TOLL-FREE 1.800.54.AVENT
En EE.UU. faricado para Philips Consumer Lifestyle,
Una división de Philips Electronics North America Corporation,
P.O. Box 10313,, Stamford, CT 06904
En Canadá importado para Philips Electronics Ltd,
281 Hillmount Road, Markham, ON L6C2S3
Llame gratuítamente: 1.800.54.AVENT
Aux États-Unis fabriqué pour: Mode de Vie/ Consommateurs Philips,
une division de Philips Electronics North America Corporation,
P.O. Box 10313, Stamford, CT 06904
Au Canada importé pour Philips Électronique Ltée,
281 Hillmount Road, Markham, ON L6C2S3
Appelez SANS FRAIS: 1.800.54.AVENT
SCD610_609

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project