advertisement
HP ProBook User Guide
© Copyright 2009 Hewlett-Packard
Development Company, L.P.
Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard
Company under license. Intel is a trademark of Intel Corporation in the U.S. and other countries or regions. Java is a U.S.
trademark of Sun Microsystems, Inc.
Microsoft, Windows, and Windows Vista are
U.S. registered trademarks of Microsoft
Corporation. SD Logo is a trademark of its proprietor.
The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services.
Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
First Edition: September 2009
Document Part Number: 570781-001
Product notice
This user guide describes features that are common to most models. Some features may not be available on your computer.
Safety warning notice
WARNING!
To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter to contact the skin or a soft surface, such as pillows or rugs or clothing, during operation. The computer and the
AC adapter comply with the user-accessible surface temperature limits defined by the International
Standard for Safety of Information Technology Equipment (IEC 60950).
iii
iv Safety warning notice
Table of contents
2 Wireless, modem, and local area network
v
3 Pointing devices and keyboard
Enabling and disabling the embedded numeric keypad .................................... 47
Switching key functions on the embedded numeric keypad ............................. 47
vi
The optical disc tray does not open for removal of a CD, DVD, or BD ............. 63
The computer does not detect the optical drive ................................................ 63
Obtaining the latest HP device drivers ............................................. 66
Obtaining Microsoft device drivers ................................................... 66
vii
Resolving a low battery level when external power is available ....... 80
Resolving a low battery level when the computer cannot exit
Step 5: Reenable Hibernation and Sleep .......................................................... 83
viii
Managing a BIOS administrator password ...................................................... 125
Entering a BIOS administrator password ........................................................ 126
Entering an Automatic DriveLock password ................................................... 130
Removing Automatic DriveLock protection ..................................................... 131
ix
Using a Windows Vista operating system DVD (purchased separately) ........................ 147
HP Client Manager for Altiris (select models only) .......................................... 163
HP CCM (Client Configuration Manager) (select models only) ....................... 165
HP SSM (System Software Manager) ............................................................. 166
x
1 Features
Identifying hardware
Components included with the computer may vary by region and model. The illustrations in this chapter identify the standard features on most computer models.
To see a list of hardware installed in the computer, follow these steps:
1.
Select Start > Computer > System Properties.
2.
In the left pane, click Device Manager.
You can also add hardware or modify device configurations using Device Manager.
NOTE:
Windows® includes the User Account Control feature to improve the security of your computer.
You may be prompted for your permission or password for tasks such as installing applications, running utilities, or changing Windows settings. Refer to Help and Support for more information.
Top components
TouchPad
Component
(1)
(2)
(3)
Pointing stick (select models only)*
Left pointing stick button (select models only)*
TouchPad*
Description
Moves the pointer and selects or activates items on the screen.
Functions like the left button on an external mouse.
Moves the pointer and selects or activates items on the screen.
Identifying hardware 1
Component Description
(4)
(5)
Left TouchPad button* Functions like the left button on an external mouse.
Right pointing stick button (select models only)* Functions like the right button on an external mouse.
(6)
(7)
TouchPad scroll zone
Right TouchPad button*
Scrolls up or down.
Functions like the right button on an external mouse.
*This table describes factory settings. To view or change pointing device preferences, select Start > Control Panel > Hardware
and Sound > Mouse.
2 Chapter 1 Features
Lights
NOTE:
Refer to the illustration that most closely matches your computer.
Component
(1)
Wireless lights (2)*
(2)
Power lights (2) †
(3)
Battery light
(4)
Drive light
Description
● Blue: An integrated wireless device, such as a wireless local area network (WLAN) device, the HP Mobile Broadband
Module (select models only), and/or a Bluetooth® device, is on.
●
Amber: All wireless devices are off.
●
On: The computer is on.
● Blinking: The computer is in the Sleep state.
●
Off: The computer is off or in Hibernation.
● Amber: A battery is charging.
●
Turquoise: A battery is close to full charge capacity.
● Blinking amber: A battery that is the only available power source has reached a low battery level. When the battery reaches a critical battery level, the battery light begins blinking rapidly.
●
Off: If the computer is plugged into an external power source, the light turns off when all batteries in the computer are fully charged. If the computer is not plugged into an external power source, the light stays off until the battery reaches a low battery level.
●
Blinking turquoise: The hard drive or optical drive (select models only) is being accessed.
● Amber: HP 3D DriveGuard has temporarily parked the hard drive.
Identifying hardware 3
Component Description
(5)
(6)
(7)
(8)
(9)
(10)
QuickLook light
QuickWeb light
Caps lock light
Num lock light
Volume mute light
Volume down light
●
On: The computer is on.
●
Off: The computer is off or in the Sleep or Hibernation state.
On: The Web browser is in use.
On: Caps lock is on.
On: Num lock is on or the embedded numeric keypad is enabled.
●
Turquoise: Speaker sound is on.
● Amber: Speaker sound is off.
Blinking: The volume down button is being used to decrease the speaker volume.
(11)
Volume up light Blinking: The volume up button is being used to increase the speaker volume.
*The 2 wireless lights display the same information. The light on the wireless button is visible only when the computer is open.
The wireless light on the front of the computer is visible whether the computer is open or closed.
† The 2 power lights display the same information. The light on the power button is visible only when the computer is open. The power light on the front of the computer is visible whether the computer is open or closed.
Component
(1)
Wireless lights (2)*
(2)
Power lights (2) †
4 Chapter 1 Features
Description
●
Blue: An integrated wireless device, such as a wireless local area network (WLAN) device, the HP Mobile Broadband
Module (select models only), and/or a Bluetooth® device, is on.
● Amber: All wireless devices are off.
●
On: The computer is on.
● Blinking: The computer is in the Sleep state.
●
Off: The computer is off or in Hibernation.
Component Description
(3)
(4)
Battery light
Drive light
●
Amber: A battery is charging.
●
Turquoise: A battery is close to full charge capacity.
● Blinking amber: A battery that is the only available power source has reached a low battery level. When the battery reaches a critical battery level, the battery light begins blinking rapidly.
●
Off: If the computer is plugged into an external power source, the light turns off when all batteries in the computer are fully charged. If the computer is not plugged into an external power source, the light stays off until the battery reaches a low battery level.
● Blinking turquoise: The hard drive or optical drive (select models only) is being accessed.
●
Amber: HP 3D DriveGuard has temporarily parked the hard drive.
●
On: The computer is on.
(5)
QuickLook light
(6)
(7)
(8)
(9)
QuickWeb light
Caps lock light
Num lock light
Volume mute light
● Off: The computer is off or in the Sleep or Hibernation state.
On: The Web browser is in use.
On: Caps lock is on.
On: Num lock is on or the embedded numeric keypad is enabled.
(10)
Volume down light
● Turquoise: Speaker sound is on.
●
Amber: Speaker sound is off.
Blinking: The volume down button is being used to decrease the speaker volume.
(11)
Volume up light Blinking: The volume up button is being used to increase the speaker volume.
On: The Windows calculator function is on.
(12)
Calculator light
*The 2 wireless lights display the same information. The light on the wireless button is visible only when the computer is open.
The wireless light on the front of the computer is visible whether the computer is open or closed.
†
The 2 power lights display the same information. The light on the power button is visible only when the computer is open. The power light on the front of the computer is visible whether the computer is open or closed.
Buttons and fingerprint reader
NOTE:
Refer to the illustration that most closely matches your computer.
Identifying hardware 5
Component
(1)
Power button
(2)
QuickLook button
(3)
QuickWeb button
(4)
Wireless button
6 Chapter 1 Features
Description
●
When the computer is off, press the button to turn on the computer.
● When the computer is on, press the button to shut down the computer.
●
When the computer is in the Sleep state, press the button briefly to exit Sleep.
● When the computer is in Hibernation, press the button briefly to exit Hibernation.
If the computer has stopped responding and Windows shutdown procedures are ineffective, press and hold the power button for at least 5 seconds to turn off the computer.
To learn more about your power settings, select Start >
Control Panel > System and Maintenance > Power
Options.
● When the computer is off, press the button to open
HP QuickLook.
●
When the computer is on, press the button to open
Software Setup.
NOTE:
If Software Setup is not available, the default
Web browser opens.
●
When the computer is off, press the button to open
HP QuickWeb.
● When the computer is on, press the button to open the default Web browser.
Turns the wireless feature on or off but does not establish a wireless connection.
Component
(5)
(6)
(7)
(8)
Volume mute button
Volume down button
Volume up button
Fingerprint reader (select models only)
Description
Mutes and restores speaker sound.
Decreases computer volume.
Increases computer volume.
Allows a fingerprint logon to Windows, instead of a password logon.
Component
(1)
Power button
Description
●
When the computer is off, press the button to turn on the computer.
● When the computer is on, press the button to shut down the computer.
●
When the computer is in the Sleep state, press the button briefly to exit Sleep.
● When the computer is in Hibernation, press the button briefly to exit Hibernation.
If the computer has stopped responding and Windows shutdown procedures are ineffective, press and hold the power button for at least 5 seconds to turn off the computer.
To learn more about your power settings, select Start >
Control Panel > System and Maintenance > Power
Options.
Identifying hardware 7
Component
(2)
QuickLook button
(3)
QuickWeb button
(4)
(5)
(6)
(7)
Wireless button
Volume mute button
Volume down button
Volume up button
(8)
(9)
Calculator button
Fingerprint reader (select models only)
Description
●
When the computer is off, press the button to open
HP QuickLook.
●
When the computer is on, press the button to open
Software Setup.
NOTE:
If Software Setup is not available, the default
Web browser opens.
●
When the computer is off, press the button to open
HP QuickWeb.
● When the computer is on, press the button to open the default Web browser.
Turns the wireless feature on or off but does not establish a wireless connection.
Mutes and restores speaker sound.
Decreases computer volume.
Increases computer volume.
Opens the Windows calculator feature.
Allows a fingerprint logon to Windows, instead of a password logon.
8 Chapter 1 Features
Keys
NOTE:
Refer to the illustration that most closely matches your computer.
Component
(1)
esc key
(2)
fn key
(3)
(4)
(5)
(6)
Windows logo key
Windows applications key
Embedded numeric keypad keys
Function keys
Description
Displays system information when pressed in combination with the fn key.
Executes frequently used system functions when pressed in combination with a function key or the esc key.
Displays the Windows Start menu.
Displays a shortcut menu for items beneath the pointer.
Can be used like the keys on an external numeric keypad.
Execute frequently used system functions when pressed in combination with the fn key.
Identifying hardware 9
Component
(1)
esc key
(2)
fn key
(3)
(4)
(5)
(6)
Windows logo key
Windows applications key
Integrated numeric keypad keys
Function keys
Front components
Description
Displays system information when pressed in combination with the fn key.
Executes frequently used system functions when pressed in combination with a function key or the esc key.
Displays the Windows Start menu.
Displays a shortcut menu for items beneath the pointer.
Can be used like the keys on an external numeric keypad.
Execute frequently used system functions when pressed in combination with the fn key.
10 Chapter 1 Features
Component
(1)
Wireless light
(2)
Power light
(3)
Battery light
(4)
Drive light
(5)
(6)
(7)
(8)
Webcam light (select models only)
Display release latch
Speakers (2)
Business card slot
Description
●
Blue: An integrated wireless device, such as a wireless local area network (WLAN) device, the HP Mobile Broadband
Module (select models only), and/or a Bluetooth® device, is on.
●
Amber: All wireless devices are off.
● On: The computer is on.
●
Blinking: The computer is in the Sleep state.
● Off: The computer is off or in Hibernation.
● Amber: A battery is charging.
●
Turquoise: A battery is close to full charge capacity.
●
Blinking amber: A battery that is the only available power source has reached a low battery level. When the battery reaches a critical battery level, the battery light begins blinking rapidly.
●
Off: If the computer is plugged into an external power source, the light turns off when all batteries in the computer are fully charged. If the computer is not plugged into an external power source, the light stays off until the battery reaches a low battery level.
● Blinking turquoise: The hard drive or optical drive (select models only) is being accessed.
●
Amber: HP 3D DriveGuard has temporarily parked the hard drive.
On: The webcam is in use.
Opens the computer.
Produce sound.
Holds a business card in position so that the webcam (select models only) can capture an image.
Right-side components
NOTE:
Refer to the illustration that most closely matches your computer.
Identifying hardware 11
Component
(1)
Media Card Reader
(2)
(3)
(4)
Upgrade bay
USB port
1394 port
(5)
(6)
RJ-11 (modem) jack
Security cable slot
Description
Supports the following optional digital card formats:
●
Memory Stick
● Memory Stick Pro
●
Memory Stick Duo (adapter required)
● Memory Stick Duo Pro (adapter required)
●
MultiMediaCard
●
MultiMediaCard Plus
●
Secure Digital (SD) Memory Card
● Secure Digital (SD) High Capacity Memory Card
● micro Secure Digital (SD) Memory Card (adapter required)
● xD-Picture Card
Supports an optical drive or a hard drive.
Connects an optional USB device.
Connects an optional IEEE 1394 or 1394a device, such as a camcorder.
Connects a modem cable.
Attaches an optional security cable to the computer.
NOTE:
The security cable is designed to act as a deterrent, but it may not prevent the computer from being mishandled or stolen.
Component
(1)
Media Card Reader
Description
Supports the following optional digital card formats:
● Memory Stick
●
Memory Stick Pro
● Memory Stick Duo (adapter required)
●
Memory Stick Duo Pro (adapter required)
12 Chapter 1 Features
Component
(2)
(3)
(4)
Upgrade bay
USB port
1394 port
(5)
Serial port
Description
●
MultiMediaCard
●
MultiMediaCard Plus
● Secure Digital (SD) Memory Card
●
Secure Digital (SD) High Capacity Memory Card
● micro Secure Digital (SD) Memory Card (adapter required)
● xD-Picture Card
Supports an optical drive or a hard drive.
Connects an optional USB device.
Connects an optional IEEE 1394 or 1394a device, such as a camcorder.
Connects an optional device such as a serial modem, mouse, or printer.
Left-side components
NOTE:
Refer to the illustration that most closely matches your computer.
Component
(1)
Vent
(2)
DisplayPort
(3)
(4)
(5)
USB ports (3)
ExpressCard slot
Audio-in (microphone) jack
(6)
Audio-out (headphone) jack
Description
Enables airflow to cool internal components.
NOTE:
The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation.
Connects an optional digital display device such as a highperformance monitor or projector.
Connect optional USB devices.
Supports optional ExpressCards.
Connects an optional computer headset microphone, stereo array microphone, or monaural microphone.
Produces sound when connected to optional powered stereo speakers, headphones, ear buds, a headset, or television audio.
NOTE:
When a device is connected to the headphone jack, the computer speakers are disabled.
Identifying hardware 13
Component
(1)
Vent
(2)
DisplayPort
(3)
(4)
(5)
USB ports (3)
Smart card reader
Audio-in (microphone) jack
(6)
Audio-out (headphone) jack
Description
Enables airflow to cool internal components.
NOTE:
The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation.
Connects an optional digital display device such as a highperformance monitor or projector.
Connect optional USB devices.
Supports optional smart cards and Java™ Cards.
Connects an optional computer headset microphone, stereo array microphone, or monaural microphone.
Produces sound when connected to optional powered stereo speakers, headphones, ear buds, a headset, or television audio.
NOTE:
When a device is connected to the headphone jack, the computer speakers are disabled.
Rear components
NOTE:
Refer to the illustration that most closely matches your computer.
Component
(1)
(2)
(3)
RJ-45 (network) jack
External monitor port
Power connector
14 Chapter 1 Features
Description
Connects a network cable.
Connects an external VGA monitor or projector.
Connects an AC adapter.
Component
(1)
Security cable slot
(2)
(3)
(4)
(5)
RJ-11 (modem) jack
RJ-45 (network) jack
External monitor port
Power connector
Bottom components
Description
Attaches an optional security cable to the computer.
NOTE:
The security cable is designed to act as a deterrent, but it may not prevent the computer from being mishandled or stolen.
Connects a modem cable.
Connects a network cable.
Connects an external VGA monitor or projector.
Connects an AC adapter.
Component
(1)
Battery bay
Description
Holds the battery.
Identifying hardware 15
Component
(2)
(3)
(4)
(5)
(6)
(7)
SIM slot
Battery release latch
Docking connector
Accessory battery connector
Bluetooth compartment
Vents (6)
(8)
HP Mobile Broadband Module compartment
(9)
(10)
Memory module compartment
Hard drive bay
Description
Contains a wireless subscriber identity module (SIM) (select models only). The SIM slot is located inside the battery bay.
Releases the battery from the battery bay.
Connects an optional docking device.
Connects an optional accessory battery.
Contains a Bluetooth device.
Enable airflow to cool internal components.
NOTE:
The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation.
Contains an HP Mobile Broadband Module (select models only).
NOTE:
To prevent an unresponsive system, replace the wireless module only with a wireless module authorized for use in the computer by the governmental agency that regulates wireless devices in your country or region. If you replace the module and then receive a warning message, remove the module to restore computer functionality, and then contact technical support through
Help and Support.
Contains an expansion memory module slot.
Holds the hard drive.
Display components
NOTE:
Your computer may look slightly different from the illustration in this section.
16 Chapter 1 Features
Component
(1)
Internal display switch
(2)
Internal microphones (2)
(3)
(4)
Webcam light (select models only)
Webcam (select models only)
Description
Turns off the display or initiates Sleep if the display is closed while the power is on.
Record sound.
NOTE:
If there is a microphone icon next to each microphone opening, your computer has internal microphones.
On: The webcam is in use.
Records audio and video and captures still photographs.
Wireless antennas (select models only)
NOTE:
Your computer may look slightly different from the illustration in this section.
Identifying hardware 17
Component Description
(1)
(2)
WWAN antennas (2)*
WLAN antennas (2)*
Send and receive wireless signals to communicate with wireless wide-area networks (WWAN).
Send and receive wireless signals to communicate with wireless local area networks (WLAN).
*The antennas are not visible from the outside of the computer. For optimal transmission, keep the areas immediately around the antennas free from obstructions.
To see wireless regulatory notices, refer to the section of the Regulatory, Safety and Environmental
Notices that applies to your country or region. These notices are located in Help and Support.
18 Chapter 1 Features
Additional hardware components
Component Description
(1)
(2)
Power cord*
Battery*
Connects an AC adapter to an AC outlet.
Powers the computer when the computer is not plugged into external power.
(3)
AC adapter Converts AC power to DC power.
*Batteries and power cords vary in appearance by region and country.
Identifying the labels
The labels affixed to the computer provide information you may need when you troubleshoot system problems or travel internationally with the computer:
●
Service tag—Provides important information, including the following:
◦
Product Name (1). This is the product name affixed to the front of your computer.
◦ Serial Number (s/n) (2). This is an alphanumeric identifier that is unique to each product.
◦
Part number/Product number (p/n) (3). This number provides specific information about the product's hardware components. The part number helps a service technician to determine what components and parts are needed.
◦ Model description (4). This is an alphanumeric identifier used to locate documents, drivers, and support for your computer.
◦
Warranty period (5). This number describes the duration (in years) of the warranty period for this computer.
Identifying the labels 19
Have this information available when you contact technical support. The service tag label is affixed to the bottom of the computer.
●
Microsoft® Certificate of Authenticity—Contains the Windows Product Key. You may need the
Product Key to update or troubleshoot the operating system. This certificate is affixed to the bottom of the computer.
●
Regulatory label—Provides regulatory information about the computer. The regulatory label is affixed inside the battery bay.
● Wireless certification label(s) (select models only)—Provide information about optional wireless devices and the approval markings of some of the countries or regions in which the devices have been approved for use. An optional device may be a wireless local area network (WLAN) device or an optional Bluetooth® device. If your computer model includes one or more wireless devices, one or more certification labels are included with your computer. You may need this information when traveling internationally. Wireless certification labels are affixed to the bottom of the computer.
●
SIM (subscriber identity module) label (select models only)—Provides the ICCID (Integrated Circuit
Card Identifier) of your SIM. This label is located inside the battery bay.
● HP Mobile Broadband Module serial number label (select models only)—Provides the serial number of your HP Mobile Broadband Module. This label is located inside the battery bay.
20 Chapter 1 Features
2 Wireless, modem, and local area network
Using wireless devices (select models only)
Wireless technology transfers data across radio waves instead of wires. Your computer may be equipped with one or more of the following wireless devices:
●
Wireless local area network (WLAN) device—Connects the computer to wireless local area networks (commonly referred to as Wi-Fi networks, wireless LANs, or WLANs) in corporate offices, your home, and public places such as airports, restaurants, coffee shops, hotels, and universities.
In a WLAN, each mobile wireless device communicates with a wireless router or a wireless access point.
●
HP Mobile Broadband Module—A wireless wide area network (WWAN) device that provides access to information wherever mobile network operator service is available. In a WWAN, each mobile device communicates to a mobile network operator’s base station. Mobile network operators install networks of base stations (similar to cell phone towers) throughout large geographic areas, effectively providing coverage across entire states, regions, or even countries.
●
Bluetooth® device—Creates a personal area network (PAN) to connect to other Bluetooth-enabled devices such as computers, phones, printers, headsets, speakers, and cameras. In a PAN, each device communicates directly with other devices, and devices must be relatively close together— typically within 10 meters (approximately 33 feet) of each other.
Computers with WLAN devices support one or more of the following IEEE industry standards:
●
802.11b, the first popular standard, supports data rates of up to 11 Mbps and operates at a frequency of 2.4 GHz.
●
802.11g supports data rates of up to 54 Mbps and operates at a frequency of 2.4 GHz. An 802.11g
WLAN device is backward compatible with 802.11b devices, so they can operate on the same network.
● 802.11a supports data rates of up to 54 Mbps and operates at a frequency of 5 GHz.
NOTE:
802.11a is not compatible with 802.11b and 802.11g.
●
802.11n supports data rates of up to 450 Mbps and may operate at 2.4 GHz or 5 GHz, making it backward compatible with 802.11a, b, and g.
NOTE:
The specifications for the 802.11n WLAN are draft specifications and are not final. If the final specifications differ from the draft specifications, it may affect the ability of the computer to communicate with other 802.11n WLAN devices.
Using wireless devices (select models only) 21
For more information on wireless technology, refer to the information and Web site links provided in
Help and Support.
Identifying wireless and network icons
Icon Name Description
Wireless (connected) Identifies the location of the wireless lights and the wireless buttons on the computer. Also identifies the Wireless Assistant software on the computer and indicates that one or more of the wireless devices are on.
Wireless
(disconnected)
HP Connection
Manager
Identifies the Wireless Assistant software on the computer and indicates that all of the wireless devices are off.
Opens HP Connection Manager, which enables you to create a connection with an HP Mobile Broadband device (select models only).
Network status
(connected)
Indicates that one or more of your network drivers are installed and one or more network devices are connected to the network.
Network status
(disconnected)
Indicates that one or more of your network drivers are installed but no network devices are connected to the network.
Using the wireless controls
You can control the wireless devices in your computer using these features:
●
Wireless button
● Wireless Assistant software (select models only)
●
HP Connection Manager software (select models only)
● Operating system controls
Using the wireless button
The computer has a wireless button, one or more wireless devices, and two wireless lights. All of the wireless devices on your computer are enabled at the factory, so the wireless light is on (blue) when you turn on the computer.
The wireless light indicates the overall power state of your wireless devices, not the status of individual devices. If the wireless light is blue, at least one wireless device is on. If the wireless light is amber, all wireless devices are off.
Because the wireless devices are enabled at the factory, you can use the wireless button to turn on or turn off the wireless devices simultaneously. Individual wireless devices can be controlled through
Wireless Assistant software (select models only) or through Computer Setup.
22 Chapter 2 Wireless, modem, and local area network
NOTE:
If the wireless devices are disabled by Computer Setup, the wireless button will not work until you reenable your devices.
Using Wireless Assistant software (select models only)
A wireless device can be turned on or off using the Wireless Assistant software. If a wireless device is disabled by Computer Setup, it must be reenabled by Computer Setup before it can be turned on or off using Wireless Assistant.
NOTE:
Enabling or turning on a wireless device does not automatically connect the computer to a network or a Bluetooth-enabled device.
To view the state of the wireless devices, position the cursor over the wireless icon in the notification area, at the far right of the taskbar.
NOTE:
To display the Wireless icon, click the Show Hidden Icons icon (< or <<) in the notification area.
If the wireless icon is not displayed in the notification area, complete the following steps to change the
Wireless Assistant properties:
1.
Select Start > Control Panel > Mobile PC > Windows Mobility Center.
2.
Click the wireless icon in the Wireless Assistant tile, which is located in the bottom-left corner of
Windows® Mobility Center.
3.
Click Properties.
4.
Select the check box next to HP Wireless Assistant icon in notification area.
5.
Click Apply.
For more information, refer to the Wireless Assistant software Help:
1.
Open Wireless Assistant by clicking the wireless icon in Windows Mobility Center.
2.
Click the Help button.
Using HP Connection Manager (select models only)
You can use HP Connection Manager to connect to WWANs using the HP Mobile Broadband device in your computer (select models only).
To start Connection Manager, click the Connection Manager icon in the notification area, at the far right of the taskbar.
– or –
Select Start > All Programs > HP > HP Connection Manager.
For more details about using Connection Manager, refer to the Connection Manager software Help.
Using operating system controls
Some operating systems also offer a way to manage integrated wireless devices and the wireless connection. For example, Windows provides the Network and Sharing Center that allows you to set up a connection or network, connect to a network, manage wireless networks, and diagnose and repair connections.
Using wireless devices (select models only) 23
To access the Network and Sharing Center, click Start > Control Panel > Network and Internet >
Network and Sharing Center.
For more information, refer to Help and Support. Click Start > Help and Support.
24 Chapter 2 Wireless, modem, and local area network
Using a WLAN device (select models only)
With a WLAN device, you can access a wireless local area network (WLAN), which is composed of other computers and accessories that are linked by a wireless router or a wireless access point.
NOTE:
The terms wireless router and wireless access point are often used interchangeably.
●
A large-scale WLAN, such as a corporate or public WLAN, typically uses wireless access points that can accommodate a large number of computers and accessories and can separate critical network functions.
●
A home or small office WLAN typically uses a wireless router, which allows several wireless and wired computers to share an Internet connection, a printer, and files without requiring additional pieces of hardware or software.
NOTE:
To use the WLAN device in your computer, you must connect to a WLAN infrastructure
(provided through a service provider or a public or corporate network).
Setting up a WLAN
To set up a WLAN and connect to the Internet, you need the following equipment:
●
A broadband modem (either DSL or cable) (1) and high-speed Internet service purchased from an
Internet service provider (ISP)
● A wireless router (purchased separately) (2)
●
The wireless computer (3)
The following illustration shows an example of a wireless network installation that is connected to the
Internet.
As your network grows, additional wireless and wired computers can be connected to the network to access the Internet.
For help in setting up your WLAN, refer to the information provided by your router manufacturer or your
ISP.
Protecting your WLAN
Because the WLAN standard was designed with only limited security capabilities—basically to foil casual eavesdropping rather than more powerful forms of attack—it is essential to understand that WLANs are vulnerable to well-known and well-documented security weaknesses.
WLANs in public areas, or “hotspots,” like coffee shops and airports may not provide any security. New technologies are being developed by wireless manufacturers and hotspot service providers that make the public environment more secure and anonymous. If you are concerned about the security of your computer in a hotspot, limit your network activities to noncritical e-mail and basic Internet surfing.
Using a WLAN device (select models only) 25
When you set up a WLAN or access an existing WLAN, always enable security features to protect your network from unauthorized access. The common security levels are Wi-Fi Protected Access (WPA) and
Wired Equivalent Privacy (WEP). Because wireless radio signals travel outside the network, other WLAN devices can pick up unprotected signals and either connect to your network (uninvited) or capture information being sent across it. However, you can take precautions to protect your WLAN:
●
Use a wireless transmitter with built-in security.
Many wireless base stations, gateways, and routers provide built-in security features such as wireless security protocols and firewalls. With the correct wireless transmitter, you can protect your network from the most common wireless security risks.
●
Work behind a firewall.
A firewall is a barrier that checks both data and requests for data that are sent to your network and then discards any suspicious items. Firewalls are available in many varieties, both software and hardware. Some networks use a combination of both types.
●
Use wireless encryption.
A variety of sophisticated encryption protocols is available for your WLAN. Find the solution that works best for your network security:
◦ Wired Equivalent Privacy (WEP) is a wireless security protocol that uses a WEP key to encode or encrypt all network data before it is transmitted. Usually, you can allow the network to assign the WEP key. Alternatively, you can set up your own key, generate a different key, or choose other advanced options. Without the correct key, others will not be able to use the
WLAN.
◦
WPA (Wi-Fi Protected Access), like WEP, uses security settings to encrypt and decrypt data that is transmitted over the network. However, instead of using one static security key for encryptions as WEP does, WPA uses temporal key integrity protocol (TKIP) to dynamically generate a new key for every packet. It also generates different sets of keys for each computer on the network.
●
Close your network.
If possible, prevent your network name (SSID) from being broadcast by the wireless transmitter.
Most networks initially broadcast the name, telling any computer nearby that your network is available. By closing the network, other computers are less likely to know that your network exists.
NOTE:
If your network is closed and the SSID is not broadcast, you will need to know or remember the SSID to connect new devices to the network. Write down the SSID and store it in a secure place before closing the network.
26 Chapter 2 Wireless, modem, and local area network
Connecting to a WLAN
To connect to the WLAN, follow these steps:
1.
Be sure that the WLAN device is on. If it is on, the wireless light is on. If the wireless light is amber, press the wireless button.
2.
Select Start > Connect to.
3.
Select your WLAN from the list, and then type the network security key, if required.
●
If the network is unsecured, meaning that anyone can access the network, a warning is displayed. Click Connect Anyway to accept the warning and complete the connection.
●
If the network is a security-enabled WLAN, you are prompted to enter a network security key, which is a security code. Type the code, and then click Connect to complete the connection.
NOTE:
If no WLANs are listed, you are out of range of a wireless router or access point.
NOTE:
If you do not see the network you want to connect to, click Set up a connection or
network. A list of options is displayed. You can choose to manually search for and connect to a network or to create a new network connection.
After the connection is made, place the cursor over the network status icon in the notification area, at the far right of the taskbar, to verify the name and status of the connection.
NOTE:
The functional range (how far your wireless signals travel) depends on WLAN implementation, router manufacturer, and interference from other electronic devices or structural barriers such as walls and floors.
More information about using a WLAN is available through the following resources:
● Information from your ISP and the manufacturer's instructions included with your wireless router and other WLAN equipment
●
Information and Web site links provided in Help and Support
For a list of public WLANs near you, contact your ISP or search the Web. Web sites that list public
WLANs include Cisco Internet Mobile Office Wireless Locations, Hotspotlist, and Geektools. Check with each public WLAN location for cost and connection requirements.
For additional information on connecting your computer to a corporate WLAN, contact your network administrator or IT department.
Roaming to another network
When you move your computer within range of another WLAN, Windows attempts to connect to that network. If the attempt is successful, your computer is automatically connected to the new network. If
Windows does not recognize the new network, follow the same procedure you used initially to connect to your WLAN.
Using a WLAN device (select models only) 27
Using HP Mobile Broadband (select models only)
HP Mobile Broadband enables your computer to use wireless wide area networks (WWANs) to access the Internet from more places and over larger areas than it can by using WLANs. Using HP Mobile
Broadband requires a network service provider (called a mobile network operator), which in most cases is a mobile phone network operator. Coverage for HP Mobile Broadband is similar to mobile phone voice coverage.
When used with mobile network operator service, HP Mobile Broadband gives you the freedom to stay connected to the Internet, send e-mail, or connect to your corporate network whether you are on the road or outside the range of Wi-Fi hotspots.
HP supports the following technologies:
●
HSPA (High Speed Packet Access), which provides access to networks based on the Global
System for Mobile Communications (GSM) telecommunications standard.
●
EV-DO (Evolution Data Optimized), which provides access to networks based on the code division multiple access (CDMA) telecommunications standard.
You may need the HP Mobile Broadband Module serial number to activate mobile broadband service.
The serial number is printed on a label inside the battery bay of your computer.
Some mobile network operators require the use of a subscriber identity module (SIM). A SIM contains basic information about you, such as a PIN (personal identification number), as well as network information. The computer includes a SIM that is preinstalled in the battery bay. If the SIM is not preinstalled, it may be provided in the HP Mobile Broadband information provided with your computer or the mobile network operator may provide it separately from the computer.
For information on inserting and removing the SIM, refer to the following “Inserting a SIM” and “Removing a SIM” sections.
For information on HP Mobile Broadband and how to activate service with a preferred mobile network operator, refer to the mobile broadband information included with your computer. For additional information, see the HP Web site at http://www.hp.com/go/mobilebroadband (US only).
Inserting a SIM
CAUTION:
To prevent damage to the connectors, use minimal force when inserting a SIM.
To insert a SIM:
1.
Shut down the computer. If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the power button. Then shut down the computer through the operating system.
2.
Close the display.
3.
Disconnect all external devices connected to the computer.
4.
Unplug the power cord from the AC outlet.
5.
Turn the computer upside down on a flat surface, with the battery bay toward you.
6.
Remove the battery.
28 Chapter 2 Wireless, modem, and local area network
7.
Insert the SIM into the SIM slot, and gently push the SIM into the slot until it is firmly seated.
8.
Replace the battery.
NOTE:
HP Mobile Broadband will be disabled if the battery is not replaced.
9.
Reconnect external power.
10.
Reconnect external devices.
11.
Turn on the computer.
Removing a SIM
To remove a SIM:
1.
Shut down the computer. If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the power button. Then shut down the computer through the operating system.
2.
Close the display.
3.
Disconnect all external devices connected to the computer.
4.
Unplug the power cord from the AC outlet.
5.
Turn the computer upside down on a flat surface, with the battery bay toward you.
6.
Remove the battery.
Using HP Mobile Broadband (select models only) 29
7.
Press in on the SIM (1), and then remove it from the slot (2).
8.
Replace the battery.
9.
Reconnect external power.
10.
Reconnect external devices.
11.
Turn on the computer.
30 Chapter 2 Wireless, modem, and local area network
Using a Bluetooth wireless device
A Bluetooth device provides short-range wireless communications that replace the physical cable connections that traditionally link electronic devices such as the following:
●
Computers (desktop, notebook, PDA)
●
Phones (cellular, cordless, smart phone)
●
Imaging devices (printer, camera)
●
Audio devices (headset, speakers)
Bluetooth devices provide peer-to-peer capability that allows you to set up a personal area network
(PAN) of Bluetooth devices. For information on configuring and using Bluetooth devices, refer to the
Bluetooth software Help.
Bluetooth and Internet Connection Sharing (ICS)
HP does not recommend setting up one computer with Bluetooth as a host and using it as a gateway through which other computers may connect to the Internet. When two or more computers are connected using Bluetooth, and Internet Connection Sharing (ICS) is enabled on one of the computers, the other computers may not be able to connect to the Internet using the Bluetooth network.
The strength of Bluetooth is in synchronizing information transfers between your computer and wireless devices including cellular phones, printers, cameras, and PDAs. The inability to consistently connect two or more computers to share the Internet through Bluetooth is a limitation of Bluetooth and the
Windows® operating system.
Using a Bluetooth wireless device 31
Troubleshooting wireless network problems
Some possible causes for wireless connection problems include the following:
●
Wireless device is not installed correctly or has been disabled.
●
Wireless device or router hardware has failed.
●
Network configuration (SSID or security) has been changed.
● Wireless device encountered interference from other devices.
NOTE:
Wireless networking devices are included with select computer models only. If wireless networking is not listed in the feature list on the side of the original computer package, you may add wireless networking capability to the computer by purchasing a wireless networking device.
Before working your way through the sequence of possible solutions to your network connection problem, be sure that device drivers are installed for all wireless devices.
Use the procedures in this chapter to diagnose and repair a computer that does not connect to the network you want to use.
Cannot create a WLAN connection
If you have a problem connecting to a WLAN, confirm that the integrated WLAN device is properly installed on your computer:
NOTE:
Windows includes the User Account Control feature to improve the security of your computer.
You may be prompted for your permission or password for tasks such as installing software, running utilities, or changing Windows settings. Refer to Help and Support for more information.
1.
Select Start > Computer > System properties.
2.
In the left pane, click Device Manager.
3.
Identify the WLAN device from the Network adapters list. The listing for a WLAN device may include the term wireless, wireless LAN, WLAN, or 802.11.
If no WLAN device is listed, either your computer does not have an integrated WLAN device, or the driver for the WLAN device is not properly installed.
For more information on troubleshooting WLANs, refer to the Web site links provided in Help and
Support.
32 Chapter 2 Wireless, modem, and local area network
Cannot connect to a preferred network
Windows can automatically repair a corrupted WLAN connection:
●
If there is a network status icon in the notification area, at the far right of the taskbar, right-click the icon, and then click Diagnose and repair from the menu.
Windows resets your network device and attempts to reconnect to one of the preferred networks.
●
If an “x” is superimposed over the network status icon, one or more of your WLAN or LAN drivers are installed but the computer is not connected.
●
If there is no network status icon in the notification area, follow these steps:
1.
Click Start and type network and sharing in the Start Search box.
2.
From the list of search results, click Network and Sharing Center.
3.
In the left pane, click Diagnose and repair.
The Network connections window is displayed, and Windows resets your network device and attempts to reconnect to one of the preferred networks.
Network status icon is not displayed
If the network status icon is not displayed in the notification area after you configure the WLAN, the software driver is either missing or corrupted. A Windows “Device not Found” error message may also be displayed. The driver must be reinstalled.
To get the latest version of the WLAN device software for your computer, follow these steps:
1.
Open your Internet browser and go to http://www.hp.com/support .
2.
Select your country or region.
3.
Click the option for software and driver downloads, and then type your computer model number in the search box.
4.
Press enter , and then follow the on-screen instructions.
NOTE:
If the WLAN device you are using was purchased separately, consult the manufacturer's Web site for the latest software.
Current network security codes are unavailable
If you are prompted for a network key or an SSID when connecting to a WLAN, the network is protected by security. You must have the current codes to make a connection on a secure network. The SSID and network key are alphanumeric codes that you enter into your computer to identify your computer to the network.
●
For a network connected to your personal wireless router, review the router user guide for instructions on setting up the same codes on both the router and the WLAN device.
●
For a private network, such as a network in an office or at a public Internet chat room, contact the network administrator to obtain the codes, and then enter the codes when prompted to do so.
Some networks change the SSID or network keys used in their routers or access points on a regular basis to improve security. You must change the corresponding code in your computer accordingly.
Troubleshooting wireless network problems 33
If you are provided with new wireless network keys and SSID for a network, and if you have previously connected to that network, follow these steps to connect to the network:
1.
Click Start > Network > Network and Sharing Center > Manage wireless networks.
A list showing the available WLANs is displayed. If you are in a hotspot where several WLANs are active, several will be displayed.
2.
Right-click the network, and then click Properties.
NOTE:
If the network you want is not listed, check with the network administrator to be sure that the router or access point is operating.
3.
Click the Security tab, and then enter the correct wireless encryption data into the Network
security key field.
4.
Click OK to save these settings.
WLAN connection is very weak
If the connection is very weak, or if your computer cannot make a connection to a WLAN, minimize interference from other devices, as follows:
● Move your computer closer to the wireless router or access point.
●
Temporarily disconnect other wireless devices such as a microwave, cordless phone, or cellular phone to be sure that they are not interfering.
If the connection does not improve, try forcing the device to reestablish all connection values:
1.
Click Start > Network > Network and Sharing Center > Manage wireless networks.
A list showing the available WLANs is displayed. If you are in a hotspot where several WLANs are active, several will be displayed.
2.
Right-click a network, and then click Remove network.
Cannot connect to the wireless router
If you are trying to connect to the wireless router and are unsuccessful, reset the wireless router by removing power from the router for 10 to 15 seconds.
If the computer still cannot make a connection to a WLAN, restart the wireless router. For details, refer to the router manufacturer's instructions.
34 Chapter 2 Wireless, modem, and local area network
Using the modem (select models only)
The modem must be connected to an analog telephone line using a 6-pin, RJ-11 modem cable
(purchased separately). In some countries or regions, a country- or region-specific modem cable adapter
(purchased separately) is also required. Jacks for digital PBX systems may resemble analog telephone jacks, but they are not compatible with the modem.
WARNING!
Connecting the internal analog modem to a digital line can permanently damage the modem. Immediately disconnect the modem cable if you accidentally connect it to a digital line.
If the modem cable contains noise suppression circuitry (1), which prevents interference from TV and radio reception, orient the circuitry end (2) of the cable toward the computer.
Connecting a modem cable
WARNING!
To reduce the risk of electric shock, fire, or damage to the equipment, do not plug a modem cable (purchased separately) or telephone cable into the RJ-45 (network) jack.
To connect a modem cable:
1.
Plug the modem cable into the modem jack (1) on the computer.
2.
Plug the modem cable into the RJ-11 telephone wall jack (2).
Using the modem (select models only) 35
Connecting a country- or region-specific modem cable adapter
Telephone jacks vary by country or region. To use the modem and the modem cable (purchased separately) outside the country or region in which you purchased the computer, you must obtain a country- or region-specific modem cable adapter (purchased separately).
To connect the modem to an analog telephone line that does not have an RJ-11 telephone jack, follow these steps:
1.
Plug the modem cable into the modem jack (1) on the computer.
2.
Plug the modem cable into the country- or region-specific modem cable adapter (2).
3.
Plug the country- or region-specific modem cable adapter (3) into the telephone wall jack.
Selecting a location setting
Viewing the current location selection
To view the current location setting for the modem, follow these steps:
1.
Select Start > Control Panel.
2.
Click Clock, Language, and Region.
3.
Click Regional and Language Options.
4.
Your location is displayed under Location.
36 Chapter 2 Wireless, modem, and local area network
Adding new locations when traveling
By default, the only location setting available to the modem is a location setting for the country or region in which you purchased the computer. As you travel to different countries or regions, set the internal modem to a location setting that meets the operating standards of the country or region in which you are using the modem.
As you add new location settings, they are saved by the computer so that you can switch among settings at any time. You can add multiple location settings for any country or region.
CAUTION:
To prevent losing your home country or region settings, do not delete your current modem country or region settings. To enable modem use in other countries or regions while preserving your home country or region configuration, add a new configuration for each location in which you will use the modem.
CAUTION:
To prevent configuring the modem in a way that violates the telecommunications regulations and laws of the country or region you are visiting, select the country or region in which the computer is located. The modem may not function properly if the correct country or region selection is not made.
To add a location setting for the modem, follow these steps:
1.
Select Start > Control Panel > Hardware and Sound > Phone and Modem Options.
2.
Then click the Dialing Rules tab.
3.
Click New. (The New Location window is displayed.)
4.
In the Location name box, type a name (such as “home” or “work”) for the new location setting.
5.
Select a country or region from the Country/region drop-down list. (If you select a country or region that is not supported by the modem, the Country/region selection for USA or UK is displayed by default.)
6.
Enter the area code, a carrier code (if necessary), and the number to access an outside line (if necessary).
7.
Next to Dial using, click Tone or Pulse.
8.
Click OK to save your new location setting. (The Phone and Modem Options window is displayed.)
9.
Do one of the following:
●
To set your new location setting as the current location, click OK.
● To select another location setting as the current location setting, select your preference from the settings in the Location list, and then click OK.
NOTE:
You can use the preceding procedure to add location settings for places within your own country or region as well as in other countries or regions. For example, you could add a setting named “Work” that includes dialing rules for accessing an outside line.
Using the modem (select models only) 37
Solving travel connection problems
If you experience modem connection problems when using the computer outside of the country or region in which you purchased it, try the following suggestions.
●
Check the telephone line type.
The modem requires an analog, not a digital, telephone line. A line described as a PBX line is usually a digital line. A telephone line described as a data line, fax machine line, modem line, or standard telephone line is usually an analog line.
●
Check for pulse or tone dialing.
An analog telephone line supports one of 2 dialing modes: pulse dialing or tone dialing. These dialing mode options are selected in the Phone and Modem Options settings. The dialing mode option selected must match the dialing mode supported by the telephone line in your location.
To determine the dialing mode supported by a telephone line, dial a few digits on the telephone, and then listen for clicks (pulses) or tones. Clicks indicate that the telephone line supports pulse dialing. Tones indicate that the telephone line supports tone dialing.
To change the dialing mode in your current modem location setting, follow these steps:
1.
Select Start > Control Panel > Hardware and Sound > Phone and Modem Options.
2.
Then click the Dialing Rules tab.
3.
Select your modem location setting.
4.
Click Edit.
5.
Click either Tone or Pulse.
6.
Click OK twice.
●
Check the telephone number you are dialing and the response of the remote modem.
Dial a telephone number, make sure there is a response from the remote modem, and then hang up.
●
Set the modem to ignore dial tones.
If the modem receives a dial tone it does not recognize, it does not dial and displays a “No Dial
Tone” error message.
To set the modem to ignore all dial tones before dialing, follow these steps:
1.
Select Start > Control Panel > Hardware and Sound > Phone and Modem Options.
2.
Then click the Modems tab.
3.
Click the listing for the modem.
4.
Click Properties.
5.
Click Modem.
6.
Clear the check box for Wait for dial tone before dialing.
7.
Click OK twice.
38 Chapter 2 Wireless, modem, and local area network
Connecting to a local area network (LAN)
Connecting to a local area network (LAN) requires an 8-pin, RJ-45 network cable (purchased separately). If the network cable contains noise suppression circuitry (1), which prevents interference from TV and radio reception, orient the circuitry end of the cable (2) toward the computer.
To connect the network cable:
1.
Plug the network cable into the network jack (1) on the computer.
2.
Plug the other end of the cable into a network wall jack (2).
WARNING!
To reduce the risk of electric shock, fire, or damage to the equipment, do not plug a modem or telephone cable into the RJ-45 (network) jack.
Connecting to a local area network (LAN) 39
3 Pointing devices and keyboard
Using pointing devices
Setting pointing device preferences
Use Mouse Properties in Windows® to customize settings for pointing devices, such as button configuration, click speed, and pointer options.
To access Mouse Properties, select Start > Control Panel > Hardware and Sound > Mouse.
Using the TouchPad
To move the pointer, slide your finger across the TouchPad surface in the direction you want the pointer to go. Use the TouchPad buttons like the corresponding buttons on an external mouse. To scroll up and down using the TouchPad vertical scroll zone, slide your finger up or down over the lines.
NOTE:
If you are using the TouchPad to move the pointer, you must lift your finger off the TouchPad before moving it to the scroll zone. Simply sliding your finger from the TouchPad to the scroll zone will not activate the scrolling function.
Using the pointing stick (select models only)
Press the pointing stick in the direction you want to move the pointer on the screen. Use the left and right pointing stick buttons as you would the left and right buttons on an external mouse.
Connecting an external mouse
You can connect an external USB mouse to the computer using one of the USB ports on the computer.
A USB mouse can also be connected to the system using the ports on an optional docking device.
Using the keyboard
Using hotkeys
Hotkeys are combinations of the fn key (1) and either the esc key (2) or one of the function keys (3).
The icons on the f3 , f4 , and f8 through f10 keys represent the hotkey functions. Hotkey functions and procedures are discussed in the following sections.
NOTE:
Your computer may look slightly different from the illustration in this section.
40 Chapter 3 Pointing devices and keyboard
Function
Display system information.
Initiate Sleep.
Switch the screen image.
Display Power Assistant.
Decrease screen brightness.
Increase screen brightness.
Hotkey
fn+esc fn+f3 fn+f4 fn+f8 fn+f9 fn+f10
To use a hotkey command on the computer keyboard, follow either of these steps:
●
Briefly press the fn key, and then briefly press the second key of the hotkey command.
– or –
●
Press and hold down the fn key, briefly press the second key of the hotkey command, and then release both keys at the same time.
Displaying system information
Press fn+esc to display information about system hardware components and the system BIOS version number.
In the Windows fn+esc display, the version of the system BIOS (basic input-output system) is displayed as the BIOS date. On some computer models, the BIOS date is displayed in decimal format. The BIOS date is sometimes called the system ROM version number.
Using the keyboard 41
Initiating Sleep
CAUTION:
To reduce the risk of information loss, save your work before initiating Sleep.
Press fn+f3 to initiate Sleep.
When Sleep is initiated, your information is stored in system memory, the screen is cleared, and power is conserved. While the computer is in the Sleep state, the power lights blink.
The computer must be on before you can initiate Sleep.
NOTE:
If a critical battery level occurs while the computer is in the Sleep state, the computer initiates
Hibernation and the information stored in memory is saved to the hard drive. The factory setting for critical battery action is Hibernate, but this setting can be changed using Power Options in Windows
Control Panel.
To exit Sleep, briefly press the power button
The function of the fn+f3 hotkey can be changed. For example, you can set the fn+f3 hotkey to initiate
Hibernation instead of Sleep.
NOTE:
In all Windows operating system windows, references to the sleep button apply to the fn+f3 hotkey.
42 Chapter 3 Pointing devices and keyboard
Switching the screen image
Press fn+f4 to switch the screen image among display devices connected to the system. For example, if a monitor is connected to the computer, pressing fn+f4 alternates the screen image from computer display to monitor display to simultaneous display on both the computer and the monitor.
Most external monitors receive video information from the computer using the external VGA video standard. The fn+f4 hotkey can also alternate images among other devices receiving video information from the computer.
The following video transmission types, with examples of devices that use them, are supported by the fn+f4 hotkey:
●
LCD (computer display)
● External VGA (most external monitors)
Using the keyboard 43
Displaying Power Assistant
Press fn+f8 to open Power Assistant. Power Assistant allows you to configure system settings to optimize your computer's power consumption and battery charge. Power Assistant also provides tools and information to help you make informed decisions on power management.
NOTE:
If Power Assistant is not installed on your computer, pressing fn+f8 displays the battery charge information.
44 Chapter 3 Pointing devices and keyboard
Decreasing screen brightness
Press fn+f9 to decrease screen brightness. Hold down the hotkey to decrease the brightness level incrementally.
Increasing screen brightness
Press fn+f10 to increase screen brightness. Hold down the hotkey to increase the brightness level incrementally.
Using the keyboard 45
Using HP QuickLook 3
QuickLook 3 allows you to save calendar, contact, inbox, and task information from Microsoft Outlook to the hard drive of your computer. Then, when the computer is off, you can press the QuickLook button on the computer to view this information without waiting for the operating system to restart.
Use QuickLook 3 to manage contact information, calendar events, e-mail information, and tasks without restarting your computer.
NOTE:
QuickLook 3 does not support the Sleep state or Hibernation in Windows.
For more information about setting up and using QuickLook 3, refer to the QuickLook 3 software Help.
Using keypads
The computer includes either an embedded numeric keypad or an integrated numeric keypad. The computer also supports an optional external numeric keypad or an optional external keyboard that includes a numeric keypad.
Refer to the illustration that most closely matches your computer.
Using the embedded numeric keypad
If the computer includes an embedded numeric keypad, the 15 keys of the embedded numeric keypad can be used like the keys on an external keypad. When the embedded numeric keypad is turned on, each key on the keypad performs the function indicated by the icon in the upper-right corner of the key.
(1)
Component
fn key
46 Chapter 3 Pointing devices and keyboard
Description
Enables/disables the embedded numeric keypad when pressed in combination with the num lk key.
(2)
(3)
Component
Embedded numeric keypad num lk key
Description
Can be used like the keys on an external numeric keypad when pressed in combination with the fn and num lk keys.
Alternates between the navigation and numeric functions on the embedded numeric keypad.
NOTE:
The keypad function that is active when the computer is turned off will be reinstated when the computer is turned back on.
Enabling and disabling the embedded numeric keypad
Press fn+num lk to enable the embedded numeric keypad. Press fn+num lk again to return the keys to their standard keyboard functions.
NOTE:
The embedded numeric keypad will not function while an external keyboard or numeric keypad is connected to the computer.
Switching key functions on the embedded numeric keypad
You can temporarily alternate the functions of keys on the embedded numeric keypad between their standard keyboard functions and their keypad functions by using the fn key or the fn+shift key combination.
●
To change the function of a keypad key to keypad functions while the keypad is off, press and hold the fn key while pressing the keypad key.
●
To use the keypad keys temporarily as standard keys while the keypad is on:
◦
Press and hold the fn key to type in lowercase.
◦ Press and hold fn+shift to type in uppercase.
Using the integrated numeric keypad
If the computer includes an integrated numeric keypad, the 17 keys of the integrated numeric keypad can be used like the keys on an external keypad.
Using keypads 47
(1)
Component
num lk key
(2)
Integrated numeric keypad
Description
Alternates between the navigation and numeric functions on the integrated numeric keypad.
NOTE:
The keypad function that is active when the computer is turned off will be reinstated when the computer is turned back on.
Can be used like the keys on an external numeric keypad.
Using an optional external numeric keypad
Keys on most external numeric keypads function differently according to whether num lock is on or off.
(Num lock is turned off at the factory.) For example:
●
When num lock is on, most keypad keys type numbers.
●
When num lock is off, most keypad keys function like the arrow, page up, or page down keys.
When num lock on an external keypad is turned on, the num lock light on the computer is turned on.
When num lock on an external keypad is turned off, the num lock light on the computer is turned off.
To turn num lock on or off on an external keypad as you work:
▲
Press the num lk key on the external keypad, not on the computer.
48 Chapter 3 Pointing devices and keyboard
Cleaning the TouchPad and keyboard
Dirt and grease on the TouchPad can cause the pointer to jump around on the screen. To avoid this, clean the TouchPad with a damp cloth, and wash your hands frequently when using the computer.
WARNING!
To reduce the risk of electric shock or damage to internal components, do not use a vacuum cleaner attachment to clean the keyboard. A vacuum cleaner can deposit household debris on the keyboard surface.
Clean the keyboard regularly to prevent keys from sticking and to remove dust, lint, and particles that can become trapped beneath the keys. A can of compressed air with a straw extension can be used to blow air around and under the keys to loosen and remove debris.
Cleaning the TouchPad and keyboard 49
4 Multimedia
Multimedia features
Your computer includes multimedia features that allow you to listen to music and view pictures. Your computer may include the following multimedia components:
● Optical drive for playing audio and video discs
●
Integrated speakers for listening to music
●
Integrated microphones for recording your own audio
●
Integrated webcam that allows you to capture and share video
●
Preinstalled multimedia software that allows you to play and manage your music, movies, and pictures
NOTE:
Your computer may not include all of the components listed.
The following sections explain how to use the multimedia components included with your computer.
Adjusting the volume
You can adjust the volume using the following controls:
●
Computer volume buttons:
◦
To mute or restore volume, press the mute button (1).
◦ To decrease volume, press and hold the volume down button (2) until the desired volume level is reached.
50 Chapter 4 Multimedia
◦
To increase volume, press and hold the volume up button (3) until the desired volume level is reached.
●
Windows volume control:
a.
Click the Volume icon in the notification area, at the far right of the taskbar.
b.
Increase or decrease the volume by moving the slider up or down. Click the Mute icon to mute the volume.
– or –
a.
Right-click the Volume icon in the notification area, at the far right of the taskbar, and then click Open Volume Mixer.
b.
In the Speakers column, you can increase or decrease the volume by moving the Volume slider up or down. You can also mute the volume by clicking the Mute icon.
If the Volume icon is not displayed in the notification area, follow these steps to add it:
a.
Right-click in the notification area, and then click Properties.
b.
Click the Notification Area tab.
c.
Under System icons, select the Volume check box.
d.
Click OK.
● Program volume control:
Volume can also be adjusted within some programs.
Multimedia software
Your computer includes preinstalled multimedia software that allows you to play music and view pictures.
The following sections provide details about preinstalled multimedia software and installing multimedia software from a disc.
Multimedia software 51
Accessing your preinstalled multimedia software
To access preinstalled multimedia software:
▲
Select Start > All Programs, and then open the multimedia program you want to use.
NOTE:
Some programs may be located in subfolders.
NOTE:
For details about using software included with the computer, refer to the software manufacturer’s instructions. These instructions may be provided with the software, on disc, or on the manufacturer’s Web site.
Installing multimedia software from a disc
To install any multimedia software from a CD or DVD, follow these steps:
1.
Insert the disc into the optical drive (select models only) or an optional external optical drive.
2.
When the installation wizard opens, follow the on-screen instructions.
3.
Restart the computer if you are prompted to do so.
NOTE:
If your computer does not have an optical drive, you can connect an external optical drive
(purchased separately) to one of the USB ports on the computer.
52 Chapter 4 Multimedia
Audio
Your computer enables you to use a variety of audio features:
●
Play music using your computer speakers and/or connected external speakers
●
Record sound using the internal microphones or connect an external microphone
●
Download music from the Internet
● Create multimedia presentations using audio and images
●
Transmit sound and images with instant messaging programs
●
Stream radio programs (select models only) or receive FM radio signals
●
Create or “burn” audio CDs
Connecting external audio devices
WARNING!
To reduce the risk of personal injury, adjust the volume before putting on headphones, earbuds, or a headset. For additional safety information, refer to the Regulatory, Safety and
Environmental Notices.
To connect external devices such as external speakers, headphone, or a microphone, refer to the information provided with the device. For best results, remember the following tips:
●
Be sure that the device cable is securely connected to the correct jack on your computer. (Cable connectors are normally color-coded to match the corresponding jacks on the computer.)
● Be sure to install any drivers required by the external device.
NOTE:
A driver is a required program that acts like a translator between the device and the programs that use the device.
Checking your audio functions
To check the system sound on your computer, follow these steps:
1.
Select Start > Control Panel.
2.
Click Hardware and Sound.
3.
Click Sound.
4.
When the Sound window opens, click the Sounds tab. Under Program, select any sound event, such as a beep or alarm, and click the Test button.
You should hear sound through the speakers or through connected headphones.
To check the record functions of the computer, follow these steps:
1.
Select Start > All Programs > Accessories > Sound Recorder.
2.
Click Start Recording and speak into the microphone. Save the file to the desktop.
3.
Open Windows Media Player and play back the sound.
Audio 53
NOTE:
For best results when recording, speak directly into the microphone and record sound in a setting free of background noise.
▲
To confirm or change the audio settings on your computer, right-click the Sound icon on the taskbar, or select Start > Control Panel > Audio.
54 Chapter 4 Multimedia
Video
Your computer enables you to use a variety of video features:
●
Watch movies
●
Play games over the Internet
●
Edit pictures and video to create presentations
● Connect external video devices
Connecting an external monitor or projector
Your computer has both an external monitor port and a DisplayPort that allow you to connect external monitors and projectors.
Using the external monitor port
The external monitor port connects an external VGA display device such as an external VGA monitor or a VGA projector to the computer. The external monitor port is an analog display interface.
▲
To connect a VGA display device, connect the device cable to the external monitor port.
NOTE:
If a properly connected external display device does not display an image, press fn+f4 to transfer the image to the device. Repeatedly pressing fn+f4 alternates the screen image between the computer display and the device.
Using the DisplayPort
The DisplayPort connects a digital display device such as a high-performance monitor or projector. The
DisplayPort delivers higher performance over the VGA external monitor port and improves digital connectivity.
Video 55
▲
To connect a digital display device, connect the device cable to the DisplayPort.
NOTE:
If a properly connected external display device does not display an image, press fn+f4 to transfer the image to the device. Repeatedly pressing fn+f4 alternates the screen image between the computer display and the device.
56 Chapter 4 Multimedia
Optical drive (select models only)
Your computer may include an optical drive that expands the functionality of the computer. The optical drive allows you to read data discs, play music, and watch movies.
Identifying the optical drive
▲
Select Start > Computer.
You will see a list of all the devices installed on your computer. You may have one of the following types of drives:
●
DVD-ROM Drive
●
DVD±RW SuperMulti Double-Layer (DL) with Light Scribe Drive
NOTE:
Double-layer discs can store more data than single-layer discs. However, double-layer discs burned with this drive may not be compatible with many existing single-layer DVD drives and players.
●
Blu-ray ROM DVD±RW SuperMulti DL Drive
NOTE:
Some of these drives may not be supported by your computer.
Using optical discs (CDs, DVDs, and BDs)
An optical drive, such as a DVD-ROM drive, supports optical discs (CDs and DVDs). These discs store information, such as music, photos, and movies. DVDs have a higher storage capacity than CDs.
Your optical drive can read standard CD and DVD discs. If your optical drive is a Blu-ray Disc (BD) drive, it can also read BDs.
NOTE:
Some of the optical drives listed may not be supported by your computer. The listed drives are not necessarily all of the supported optical drives.
Some optical drives can also write to optical discs as described in the following table.
Optical drive type Write to CD-RW Write to DVD
±RW/R
Write to DVD±RW DL Write label to LightScribe
CD or DVD ±RW/R
DVD-ROM Drive
DVD±RW SuperMulti DL
LightScribe Drive* †
No
Yes
No
Yes
No
Yes
No
Yes
Blu-ray ROM DVD±RW
SuperMulti DL Drive*
Yes Yes Yes No
*Double-layer discs can store more data than single-layer discs. However, double-layer discs burned with this drive may not be compatible with many single-layer DVD drivers and players.
† LightScribe discs must be purchased separately. LightScribe creates a grayscale image similar to black-and-white photography.
CAUTION:
To prevent possible audio and video degradation, loss of information, or loss of audio or video playback functionality, do not initiate Sleep or Hibernation while reading a CD, DVD, or BD, or writing to a CD or DVD.
Optical drive (select models only) 57
Selecting the right disc (CDs, DVDs, and BDs)
An optical drive supports optical discs (CDs, DVDs, and BDs). CDs, used to store digital data, are also used for commercial audio recordings and are convenient for your personal storage needs. DVDs and
BDs are used primarily for movies, software, and data backup purposes. DVDs and BDs are the same form factor as CDs but have a much higher storage capacity.
NOTE:
The optical drive on your computer may not support all the types of optical discs discussed in this section.
CD-R discs
Use CD-R (write-once) discs to create permanent archives and to share files with virtually anyone.
Typical uses include the following:
● Distributing large presentations
●
Sharing scanned and digital photos, video clips, and written data
● Making your own music CDs
●
Keeping permanent archives of computer files and scanned home records
● Offloading files from your hard drive to free up disk space
After data is recorded, it cannot be erased or written over.
CD-RW discs
Use a CD-RW disc (a rewritable version of a CD) to store large projects that must be updated frequently.
Typical uses include the following:
●
Developing and maintaining large documents and project files
● Transporting work files
●
Making weekly backups of hard drive files
● Updating photos, video, audio, and data continuously
DVD±R discs
Use blank DVD±R discs to permanently store large amounts of information. After data is recorded, it cannot be erased or written over.
DVD±RW discs
Use DVD±RW discs if you want to be able to erase or write over data that you saved earlier. This type of disc is ideal for testing audio or video recordings before you burn them to a CD or DVD that cannot be changed.
LightScribe DVD+R discs
Use LightScribe DVD+R discs for sharing and storing data, home videos, and photos. These discs are read-compatible with most DVD-ROM drives and DVD video players. With a LightScribe-enabled drive and LightScribe software, you can write data to the disc and then add a designer label to the outside of the disc.
58 Chapter 4 Multimedia
Blu-ray Discs (BDs)
BD is a high-density optical disc format for the storage of digital information, including high-definition video. A single-layer Blu-ray Disc can store 25 GB, over 5 times the storage capacity of a single-layer
DVD at 4.7 GB. A dual-layer Blu-ray Disc can store 50 GB, almost 6 times the storage capacity of a dual-layer DVD at 8.5 GB.
Typical uses include the following:
●
Storage of large amounts of data
●
High-definition video playback and storage
●
Video games
NOTE:
As Blu-ray is a new format containing new technologies, certain disc, digital connection, compatibility and/or performance issues may arise, and do not constitute defects in the product. Flawless playback on all systems is not guaranteed.
Playing a CD, DVD, or BD
1.
Turn on the computer.
2.
Press the release button (1) on the drive bezel to release the disc tray.
3.
Pull out the tray (2).
4.
Hold the disc by the edges to avoid touching the flat surfaces and position the disc label-side up over the tray spindle.
NOTE:
If the tray is not fully accessible, tilt the disc carefully to position it over the spindle.
5.
Gently press the disc (3) down onto the tray spindle until the disc snaps into place.
6.
Close the disc tray.
If you have not yet configured AutoPlay, as described in the following section, an AutoPlay dialog box opens. It prompts you to select how you want to use the media content.
Optical drive (select models only) 59
NOTE:
For best results, be sure that your AC adapter is plugged into an external power source while playing a BD.
Configuring AutoPlay
1.
Select Start > Control Panel > Play CDs or other media automatically.
2.
Confirm that the Use AutoPlay for all media and devices check box is selected.
3.
Click Choose a default, and then select one of the available options for each media type listed.
4.
Click Save.
NOTE:
For more information about AutoPlay, select Start > Help and Support.
Changing DVD region settings
Most DVDs that contain copyrighted files also contain region codes. The region codes help protect copyrights internationally.
You can play a DVD containing a region code only if the region code on the DVD matches the region setting on your DVD drive.
CAUTION:
The region settings on your DVD drive can be changed only 5 times.
The region setting you select the fifth time becomes the permanent region setting on the DVD drive.
The number of region changes remaining is displayed on the DVD Region tab.
To change settings through the operating system:
1.
Select Start > Computer > System properties.
2.
In the left pane, click Device Manager.
NOTE:
Windows includes the User Account Control feature to improve the security of your computer. You may be prompted for your permission or password for tasks such as installing software, running utilities, or changing Windows settings. Refer to Help and Support for more information.
3.
Click the plus (+) next to DVD/CD-ROM drives.
4.
Right-click the DVD drive for which you want to change region settings, and then click
Properties.
5.
Click the DVD Region tab and change settings.
6.
Click OK.
Observing the copyright warning
It is a criminal offense, under applicable copyright laws, to make unauthorized copies of copyrightprotected material, including computer programs, films, broadcasts, and sound recordings. Do not use this computer for such purposes.
60 Chapter 4 Multimedia
CAUTION:
To prevent loss of information or damage to a disc, observe the following guidelines:
Before writing to a disc, connect the computer to a reliable external power source. Do not write to a disc while the computer is running on battery power.
Before writing to a disc, close all open programs except the disc software you are using.
Do not copy directly from a source disc to a destination disc or from a network drive to a destination disc. Save the information to your hard drive, and then burn from your hard drive to the destination disc.
Do not use the computer keyboard or move the computer while the computer is writing to a disc. The write process is sensitive to vibration.
NOTE:
For details about using software included with the computer, refer to the software manufacturer’s instructions, which may be provided on disc, in the software Help, or on the manufacturer's Web site.
Copying a CD, DVD, or BD
1.
Select Start > All Programs > Roxio > Creator Business.
2.
In the right pane, click Copy Disc.
3.
Insert the disc you want to copy into the optical drive.
4.
Click Copy at the bottom right of the screen.
Creator Business reads the source disc and copies the data to a temporary folder on your hard drive.
5.
When prompted, remove the source disc from the optical drive and insert a blank disc into the drive.
After the information is copied, the disc you created is ejected automatically.
Creating (burning) a CD or DVD
If your optical drive is a CD-RW, DVD-RW, or DVD±RW optical drive, you can use software such as
Windows Media Player to burn data and audio files, including MP3 and WAV music files. To burn video files to a CD or DVD, use MyDVD.
Observe the following guidelines when burning a CD or DVD:
●
Before burning a disc, save and close any open files and close all programs.
● A CD-R or DVD-R is usually best for burning audio files because after the information is copied, it cannot be changed.
●
Because some home and car stereos will not play CD-RWs, use CD-Rs to burn music CDs.
● A CD-RW or DVD-RW is generally best for burning data files or for testing audio or video recordings before you burn them to a CD or DVD that cannot be changed.
●
DVD players used in home systems usually do not support all DVD formats. Refer to the user guide that came with your DVD player for a list of supported formats.
● An MP3 file uses less space than other music file formats, and the process for creating an MP3 disc is the same as the process for creating a data file. MP3 files can be played only on MP3 players or on computers with MP3 software installed.
Optical drive (select models only) 61
To burn a CD or DVD, follow these steps:
1.
Download or copy the source files into a folder on your hard drive.
2.
Insert a blank CD or DVD into the optical drive (select models only) or an optional external optical drive.
3.
Select Start > All Programs and the name of the software you want to use.
4.
Select the kind of CD or DVD you want to create—data, audio, or video.
5.
Right-click Start, click Explore, and navigate to the folder where the source files are stored.
6.
Open the folder, and then drag the files to the drive that contains the blank optical disc.
7.
Initiate the burning process as directed by the program you have selected.
For specific instructions, refer to the software manufacturer's instructions. These instructions may be provided with the software, on disc, or on the manufacturer's Web site.
CAUTION:
Observe the copyright warning. It is a criminal offense, under applicable copyright laws, to make unauthorized copies of copyright-protected material, including computer programs, films, broadcasts, and sound recordings. Do not use this computer for such purposes.
Removing an optical disc (CD, DVD, or BD)
1.
Press the release button (1) on the drive bezel to release the disc tray, and then gently pull out the tray (2) until it stops.
2.
Remove the disc (3) from the tray by gently pressing down on the spindle while lifting the outer edges of the disc. Hold the disc by the edges and avoid touching the flat surfaces.
NOTE:
If the tray is not fully accessible, tilt the disc carefully as you remove it.
3.
Close the disc tray and place the disc in a protective case.
Troubleshooting
The following sections describe several common issues and resolutions.
62 Chapter 4 Multimedia
The optical disc tray does not open for removal of a CD, DVD, or BD
1.
Insert the end of a paper clip (1) into the release access in the front bezel of the drive.
2.
Press in gently on the paper clip until the disc tray is released, and then pull out the tray (2) until it stops.
3.
Remove the disc (3) from the tray by gently pressing down on the spindle while lifting the outer edges of the disc. Hold the disc by the edges and avoid touching the flat surfaces.
NOTE:
If the tray is not fully accessible, tilt the disc carefully as you remove it.
4.
Close the disc tray and place the disc in a protective case.
The computer does not detect the optical drive
If Windows does not detect an attached device, the device driver software may be missing or corrupted.
If you suspect that the DVD/CD-ROM drive is not being detected, verify that the optical drive is listed in the Device Manager utility.
1.
Remove any discs from the optical drive.
2.
Select Start > Control Panel > System and Maintenance > Device Manager. if prompted by
User Account Control, click Continue.
3.
In the Device Manager window, click the plus sign (+) next to Discs Drives or DVD/CD-ROM
drives, unless a minus sign (-) is already showing. Look for an optical drive listing.
4.
Right-click the optical device listing to perform the following tasks:
●
Update the driver.
● Uninstall the device.
Optical drive (select models only) 63
●
Scan for hardware changes. Windows scans your system for installed hardware and installs any required default drivers.
●
Click Properties to see if the device is working properly.
◦
Click Troubleshoot to fix problems.
◦ Click the Driver tab to update, disable, or uninstall drivers for this device.
A disc does not play
●
Save your work and close all open programs before playing a CD, DVD, or BD.
●
Log off the Internet before playing a CD, DVD, or BD.
●
Be sure that you insert the disc properly.
●
Be sure that the disc is clean. If necessary, clean the disc with filtered water and a lint-free cloth.
Wipe from the center of the disc to the outer edge.
●
Check the disc for scratches. If you find scratches, treat the disc with an optical disc repair kit available at many electronics stores.
●
Disable Sleep mode before playing the disc.
Do not initiate Hibernation or Sleep while playing a disc. Otherwise, you may see a warning message asking if you want to continue. If this message is displayed, click No. After you click No, the computer may behave in either of the following ways:
◦
Playback may resume.
– or –
◦
The playback window in the multimedia program may close. To return to playing the disc, click the Play button in your multimedia program to restart the disc. In rare cases, you may need to exit the program and then restart it.
●
Increase system resources:
Turn off external devices such as printers and scanners. Disconnecting these devices frees up valuable system resources and results in better playback performance.
Change desktop color properties. Because the human eye cannot easily tell the difference between colors beyond 16 bits, you should not notice any loss of color while watching a movie if you lower system color properties to 16-bit color, as follows:
1.
Right-click anywhere on the desktop except on an icon, and then select Personalize > Display
Settings.
2.
Set Colors to Medium (16 bit).
A disc does not play automatically
1.
Select Start > Control Panel > Play CDs or other media automatically.
2.
Confirm that the Use AutoPlay for all media and devices check box is selected.
3.
Click Save.
A CD, DVD, or BD should now start automatically when it is inserted into the optical drive.
64 Chapter 4 Multimedia
A movie stops, skips, or plays erratically
● Clean the disc.
●
Conserve system resources by trying the following suggestions:
◦
Log off the Internet.
◦
Change the color properties of the desktop:
1. Right-click on a blank area of the computer desktop, and select Personalize > Display
Settings.
2. Set Colors to Medium (16 bit), if this setting is not already selected.
◦
Disconnect external devices, such as a printer, scanner, camera, or handheld device.
A movie is not visible on an external display
1.
If both the computer display and an external display are turned on, press fn+f4 one or more times to switch between the 2 displays.
2.
Configure the monitor settings to make the external display primary:
a.
Right-click on a blank area of the computer desktop, and select Personalize > Display
Settings.
b.
Specify a primary display and a secondary display.
NOTE:
When using both displays, the DVD image will not appear on any display designated as the secondary display.
To get information about a multimedia question not covered in this guide, select Start > Help and
Support.
The process of burning a disc does not begin, or it stops before completion
● Be sure that all other programs are closed.
●
Turn off Sleep mode and Hibernation.
● Be sure that you are using the right kind of disc for your drive. See your user guides for more information about disc types.
●
Be sure that the disc is inserted properly.
● Select a slower write speed and try again.
●
If you are copying a disc, save the information on the source disc to your hard drive before trying to burn the contents to a new disc, and then burn from your hard drive.
● Reinstall the disc-burning device driver located in the DVD/CD-ROM drives category in Device
Manager.
Optical drive (select models only) 65
A device driver must be reinstalled
1.
Remove any discs from the optical drive.
2.
Click Start and type device manager in the Start Search box.
As you type, search results are listed in the pane above the box.
3.
In the results pane, click Device Manager. If prompted by User Account Control, click Continue.
4.
In the Device Manager window, click the plus sign (+) next to the type of driver you want to uninstall and reinstall (for example, DVD/CD-ROMs, Modems, and so on), unless a minus sign (-) is already showing.
5.
Click a listed driver, and press the delete key. When prompted, confirm that you want to delete the driver, but do not restart the computer.
Repeat for any other drivers you want to delete.
6.
In the Device Manager window, click the Scan for hardware changes icon in the toolbar. Windows scans your system for installed hardware and installs default drivers for anything requiring drivers.
NOTE:
If you are prompted to restart the computer, save all open files, and then continue with the restart.
7.
Reopen Device Manager, if necessary, and then verify that the drivers are once again listed.
8.
Try to use your device.
If uninstalling and reinstalling the default device drivers does not correct the problem, you may need to update your drivers using the procedures in the following section.
Obtaining the latest HP device drivers
Follow either of the following procedures to obtain HP device drivers.
To use the HP Update Utility:
1.
Select Start > All Programs > HP > HP Update.
2.
On the HP Welcome screen, click Settings, and then select a time when the utility should check for software updates on the Web.
3.
Click Next to immediately check for HP software updates.
To use the HP Web site:
1.
Open your Internet browser, go to http://www.hp.com/support , and select your country or region.
2.
Click the option for software and driver downloads, and then type your computer model number in the product box.
3.
Press enter , and then follow the on-screen instructions.
Obtaining Microsoft device drivers
You can obtain the latest Windows device drivers by using Microsoft® Update. This Windows feature can be set to automatically check for and install updates for your hardware drivers, as well as for the
Windows operating system and other Microsoft products.
66 Chapter 4 Multimedia
To use Microsoft Update:
1.
Open your Internet browser and go to http://www.microsoft.com
, and click Security & Updates.
2.
Click Microsoft Update to get the latest updates for your computer operating system, programs, and hardware.
3.
Follow the on-screen instructions to install Microsoft Update. If prompted by User Account Control, click Continue.
4.
Click Change settings and select a time for Microsoft Update to check for updates to the Windows operating system and other Microsoft products.
5.
If prompted to do so, restart your computer.
Optical drive (select models only) 67
Webcam (select models only)
Your computer may include an integrated webcam, located at the top of the display. With the preinstalled software, you can use the webcam to take a photo, record a video, or make an audio recording. You can preview the photo, video recording, or audio recording, and save it on your computer hard drive.
To access the webcam and HP Webcam software, select Start > All Programs > Webcam
Applications > HP Webcam.
The webcam software enables you to experiment with the following features:
●
Video—Record and play back webcam video.
● Audio—Record and play back audio.
●
Streaming video—Use with instant message software solutions that support UVC (Universal Video
Class) cameras.
● Snapshots—Take still photos.
●
Business Card Reader—Use to transform business cards into a usable database of contact information.
NOTE:
For information about using software designed for use with the integrated webcam, refer to the webcam software Help.
For optimum performance, observe the following guidelines while using the integrated webcam:
●
Be sure that you have the latest version of an instant message program before attempting a video conversation.
● The webcam may not work properly across some network firewalls.
NOTE:
If you are having trouble viewing or sending multimedia files to someone on another LAN or outside your network firewall, temporarily disable the firewall, perform the task you want to perform, and then reenable the firewall. To permanently resolve the problem, reconfigure the firewall as necessary, and adjust the policies and settings of other intrusion detection systems. For additional information, contact your network administrator or IT department.
●
Whenever possible, place bright light sources behind the webcam and out of the picture area.
Adjusting webcam properties
You can adjust webcam properties using the Properties dialog box, which is accessible from various programs that use the integrated webcam, usually from a configuration, settings, or properties menu:
●
Brightness—Controls the amount of light that is incorporated into the image. A higher brightness setting creates a brighter image; a lower brightness setting creates a darker image.
●
Contrast—Controls the difference between lighter and darker areas on the image. A higher contrast setting intensifies the image; a lower contrast setting maintains more of the original information’s dynamic range but leads to a flatter image.
●
Hue—Controls the aspect of color that distinguishes it from another color (what makes a color red, green, or blue). Hue is distinct from saturation, which measures the intensity of the hue.
●
Saturation—Controls the strength of color in the final image. A higher saturation setting creates a bolder image; a lower saturation setting creates a more subtle image.
68 Chapter 4 Multimedia
●
Sharpness—Controls the definition of edges in an image. A higher sharpness setting creates a more defined image; a lower sharpness setting creates a softer image.
●
Gamma—Controls the contrast affecting the mid-level grays or midtones of an image. Adjusting the gamma of an image allows you to change the brightness values of the middle range of gray tones without dramatically altering the shadows and highlights. A lower gamma setting makes grays look black, and makes dark colors even darker.
For information about using the webcam, select Start > Help and Support.
Capturing business card images
You can use the webcam with the HP Business Card Reader program to capture business card images and export the text to many types of address book software, such as Microsoft® Outlook Contacts.
To capture a business card image:
1.
Open HP Business Card Reader by selecting Start > All Programs > HP > HP Business Card
Reader.
2.
To capture one business card, click Quick Scan.
– or –
To capture multiple business cards, click Multi Scan.
3.
Insert a business card into the business card slot on the front of the computer (1), and slide the card to the right (2) to center it under the webcam.
NOTE:
If any text is obscured by the slot, rotate the card 180 degrees, with the text facing the webcam.
Webcam (select models only) 69
4.
Slowly lower the display (1) until the webcam light (2) blinks and you hear a sound, which indicates that the webcam is now in focus.
The webcam turns on, and the scanning process starts immediately. You will hear a camera shutter sound when the image is captured, and the information from the card is filled in the fields automatically.
5.
If you are capturing multiple business card images, remove the business card and insert another one. The webcam light turns on when the card is in focus. The webcam then captures the business card image and the webcam light turns off.
Repeat this step for additional business cards.
NOTE:
Do not move or raise the display until you have finished capturing all of the business cards.
6.
When you have finished capturing one or more business card images, remove the business card from the slot and raise the display.
7.
Review the information captured by Business Card Reader to be sure that it is complete.
For more information on using Business Card Reader, refer to the software Help.
70 Chapter 4 Multimedia
5 Power management
Setting power options
Using power-saving states
The computer has two power-saving states enabled at the factory: Sleep and Hibernation.
When Sleep is initiated, the power light blinks and the screen clears. Your work is saved to memory, letting you exit Sleep faster than exiting Hibernation. If the computer is in the Sleep state for an extended period or if the battery reaches a critical battery level while in the Sleep state, the computer initiates
Hibernation.
When Hibernation is initiated, your work is saved to a hibernation file on the hard drive and the computer turns off.
CAUTION:
To prevent possible audio and video degradation, loss of audio or video playback functionality, or loss of information, do not initiate Sleep or Hibernation while reading from or writing to a disc or an external media card.
NOTE:
You cannot initiate any type of networking connection or perform any computer functions while the computer is in the Sleep state or in Hibernation.
NOTE:
When HP 3D DriveGuard has parked a drive, the computer will not initiate Sleep or Hibernation, and the display will be turned off.
Initiating and exiting Sleep
The system is set at the factory to initiate Sleep after 15 minutes of inactivity when running on battery power and 30 minutes of inactivity when running on external power.
Power settings and timeouts can be changed using Power Options in Windows® Control Panel.
With the computer on, you can initiate Sleep in any of the following ways:
●
Close the display.
● Press fn+f3 .
●
Click Start, and then click the Power button.
● Click Start, click the arrow next to the Lock button, and then click Sleep.
To exit Sleep:
▲
Briefly press the power button.
Setting power options 71
When the computer exits Sleep, the power lights turn on and your work returns to the screen where you stopped working.
NOTE:
If you have set a password to be required when the computer exits Sleep, you must enter your
Windows password before your work will return to the screen.
Initiating and exiting Hibernation
The system is set at the factory to initiate Hibernation after 1080 minutes (18 hours) of inactivity when running on battery power, 1080 minutes (18 hours) of inactivity when running on external power, or when the battery reaches a critical battery level.
Power settings and timeouts can be changed using Power Options in Windows Control Panel.
To initiate Hibernation:
1.
Click Start, and then click the arrow next to the Lock button.
2.
Click Hibernate.
To exit Hibernation:
▲
Briefly press the power button
The power lights turn on and your work returns to the screen where you stopped working.
NOTE:
If you have set a password to be required when the computer exits Hibernation, you must enter your Windows password before your work will return to the screen.
Using the battery meter
The battery meter is located in the notification area, at the far right of the taskbar. The battery meter allows you to quickly access power settings, view remaining battery charge, and select a different power plan.
●
To display the percentage of remaining battery charge and the current power plan, move the pointer over the battery meter icon.
●
To access Power Options, or to change the power plan, click the battery meter icon and select an item from the list.
Different battery meter icons indicate whether the computer is running on battery or external power. The icon also displays a message if the battery has reached a critical battery level.
To hide or display the battery meter icon:
1.
Right-click the taskbar, and then click Properties.
2.
Click the Notification Area tab.
3.
Under System icons, clear the Power check box to hide the battery meter icon, or select the
Power check box to display the battery meter icon.
4.
Click OK.
Using power plans
A power plan is a collection of system settings that manages how the computer uses power. Power plans can help you conserve power or maximize performance.
72 Chapter 5 Power management
You can change power plan settings or create your own power plan.
Viewing the current power plan
▲
Move the pointer over the battery meter icon in the notification area, at the far right of the taskbar.
– or –
Select Start > Control Panel > System and Maintenance > Power Options.
Selecting a different power plan
▲
Click the battery meter icon in the notification area, and then select a power plan from the list.
– or –
Select Start > Control Panel > System and Maintenance > Power Options, and then select a power plan from the list.
Customizing power plans
1.
Click the battery meter icon in the notification area and then click More power options.
– or –
Select Start > Control Panel > System and Maintenance > Power Options.
2.
Select a power plan, and then click Change plan settings.
3.
Change the Turn off the display and Put the computer to sleep timeout settings, as needed.
4.
To change additional settings, click Change advanced power settings and make your changes.
Setting password protection on wakeup
To set the computer to prompt for a password when the computer exits Sleep or Hibernation, follow these steps:
1.
Select Start > Control Panel > System and Maintenance > Power Options.
2.
In the left pane, click Require a password on wakeup.
3.
Click Change Settings that are currently unavailable.
4.
Click Require a password (recommended).
5.
Click Save changes.
Setting power options 73
Using Power Assistant (select models only)
Power Assistant allows you to configure system settings to optimize your computer's power consumption and battery charge. Power Assistant provides tools and information to help you make informed decisions on power management:
●
Power consumption predictions in hypothetical system configurations
● Predefined power profiles
●
Usage details and graphs showing power consumption trends over time
Starting Power Assistant
To start Power Assistant when Windows is running:
Select Start > All Programs > HP > HP Power Assistant.
– or –
Press fn+f8 .
Power Assistant opens, and the following tabs are displayed:
●
Settings—Displays the opening page, which shows battery charge and power consumption information.
●
Preferences—Enables you to set device preferences.
●
Usage Details—Enables you to enter information about computer use.
●
Charts—Displays charts and graphs of power consumption.
●
About—Displays Power Assistant Help and version information.
For more information about using, configuring, and managing Power Assistant, refer to the Power
Assistant software Help.
Using external AC power
External AC power is supplied through one of the following devices:
WARNING!
To reduce potential safety issues, use only the AC adapter provided with the computer, a replacement AC adapter provided by HP, or a compatible AC adapter purchased from HP.
● Approved AC adapter
●
Optional docking device
Connect the computer to external AC power under any of the following conditions:
WARNING!
Do not charge the computer battery while you are onboard aircraft.
●
When you are charging or calibrating a battery
●
When you are installing or modifying system software
●
When you are writing information to a CD or DVD
74 Chapter 5 Power management
When you connect the computer to external AC power, the following events occur:
● The battery begins to charge.
●
If the computer is turned on, the battery meter icon in the notification area changes appearance.
When you disconnect external AC power, the following events occur:
●
The computer switches to battery power.
●
The display brightness is automatically decreased to save battery life. To increase display brightness, press the fn+f10 hotkey or reconnect the AC adapter.
Connecting the AC adapter
WARNING!
To reduce the risk of electric shock or damage to the equipment:
Plug the power cord into an AC outlet that is easily accessible at all times.
Disconnect power from the computer by unplugging the power cord from the AC outlet (not by unplugging the power cord from the computer).
If provided with a 3-pin attachment plug on the power cord, plug the cord into a grounded (earthed) 3pin outlet. Do not disable the power cord grounding pin, for example, by attaching a 2-pin adapter. The grounding pin is an important safety feature.
To connect the computer to external AC power, follow these steps:
1.
Plug the AC adapter into the power connector (1) on the computer.
2.
Plug the power cord into the AC adapter (2).
3.
Plug the other end of the power cord into an AC outlet (3).
Using battery power
When a charged battery is in the computer and the computer is not plugged into external power, the computer runs on battery power. When the computer is plugged into external AC power, the computer runs on AC power.
If the computer contains a charged battery and is running on external AC power supplied through the
AC adapter, the computer switches to battery power if the AC adapter is disconnected from the computer.
Using battery power 75
NOTE:
The display brightness is decreased to save battery life when you disconnect AC power. To increase display brightness, use the fn+f10 hotkey or reconnect the AC adapter.
You can keep a battery in the computer or in storage, depending on how you work. Keeping the battery in the computer whenever the computer is plugged into AC power charges the battery and also protects your work in case of a power outage. However, a battery in the computer slowly discharges when the computer is off and unplugged from external power.
WARNING!
To reduce potential safety issues, use only the battery provided with the computer, a replacement battery provided by HP, or a compatible battery purchased from HP.
Computer battery life varies, depending on power management settings, programs running on the computer, display brightness, external devices connected to the computer, and other factors.
Finding battery information in Help and Support
Help and Support provides the following tools and information about the battery:
●
Battery Check tool to test battery performance
●
Information on calibration, power management, and proper care and storage to maximize battery life
●
Information on battery types, specifications, life cycles, and capacity
To access battery information:
▲
Select Start > Help and Support > Learn > Power Plans: Frequently Asked Questions.
Using Battery Check
Battery Check provides information on the status of the battery installed in the computer.
To run Battery Check:
1.
Connect the AC adapter to the computer.
NOTE:
The computer must be connected to external power for Battery Check to function properly.
2.
Select Start > Help and Support > Troubleshoot > Power, Thermal and Mechanical.
3.
Click the Power tab, and then click Battery Check.
Battery Check examines the battery and its cells to see if they are functioning properly, and then reports the results of the examination.
Displaying the remaining battery charge
▲
Move the pointer over the battery meter icon in the notification area, at the far right of the taskbar.
– or –
View the estimated number of minutes of battery charge remaining in Windows Mobility Center:
▲
Click the battery meter icon, and then click Windows Mobility Center.
– or –
Select Start > Control Panel > Mobile PC > Windows Mobility Center.
76 Chapter 5 Power management
The time shown indicates the approximate running time remaining on the battery if the battery
continues to provide power at the current level. For example, the time remaining will decrease when a DVD is playing and will increase when a DVD stops playing.
Inserting or removing the battery
CAUTION:
Removing a battery that is the sole power source can cause loss of information. To prevent loss of information, save your work and initiate Hibernation or shut down the computer through Windows before removing the battery.
To insert the battery:
1.
Turn the computer upside down on a flat surface, with the battery bay toward you.
2.
Insert the battery (1) into the battery bay until it is seated.
The battery release latch (2) automatically locks the battery into place.
To remove the battery:
1.
Turn the computer upside down on a flat surface, with the battery bay toward you.
2.
Slide the battery release latch (1) to release the battery.
Using battery power 77
3.
Remove the battery from the computer (2).
Charging a battery
WARNING!
Do not charge the computer battery while you are onboard aircraft.
The battery charges whenever the computer is plugged into external power through an AC adapter, an optional power adapter, or an optional docking device.
The battery charges whether the computer is off or in use, but it charges faster when the computer is off.
Charging may take longer if a battery is new, has been unused for 2 weeks or more, or is much warmer or cooler than room temperature.
To prolong battery life and optimize the accuracy of battery charge displays, follow these recommendations:
● If you are charging a new battery, charge it fully before turning on the computer.
●
Charge the battery until the battery light turns off.
NOTE:
If the computer is on while the battery is charging, the battery meter in the notification area may show 100 percent charge before the battery is fully charged.
● Allow the battery to discharge below 5 percent of a full charge through normal use before charging it.
●
If the battery has been unused for one month or more, calibrate the battery instead of simply charging it.
The battery light displays charge status:
●
Amber: The battery is charging.
● Turquoise: A battery is close to full charge capacity.
78 Chapter 5 Power management
●
Blinking amber: A battery that is the only available power source has reached a low battery level.
When the battery reaches a critical battery level, the battery light begins blinking rapidly.
●
Off: If the computer is plugged into an external power source, the light turns off when all batteries in the computer are fully charged. If the computer is not plugged into an external power source, the light stays off until the battery reaches a low battery level.
Maximizing battery discharge time
Battery discharge time varies, depending on the features you use while on battery power. Maximum discharge time gradually shortens as the battery storage capacity naturally degrades.
Tips for maximizing battery discharge time:
●
Lower the brightness on the display.
●
Check the Power saver setting in Power Options.
●
Remove the battery from the computer when it is not being used or charged.
●
Store the battery in a cool, dry location.
Managing low battery levels
The information in this section describes the alerts and system responses set at the factory. Some lowbattery alerts and system responses can be changed using Power Options in Windows Control Panel.
Preferences set using Power Options do not affect lights.
Identifying low battery levels
When a battery that is the sole power source for the computer reaches a low battery level, the battery light blinks.
If a low battery level is not resolved, the computer enters a critical battery level, and the battery light blinks rapidly.
The computer takes the following actions for a critical battery level:
●
If Hibernation is enabled and the computer is on or in the Sleep state, the computer initiates
Hibernation.
●
If Hibernation is disabled and the computer is on or in the Sleep state, the computer remains briefly in the Sleep state, and then shuts down and loses any unsaved information.
Using battery power 79
Resolving a low battery level
CAUTION:
To reduce the risk of losing information when the computer reaches a critical battery level and has initiated Hibernation, do not restore power until the power lights turn off.
Resolving a low battery level when external power is available
▲
Connect one of the following devices:
●
AC adapter
● Optional expansion product or docking device
●
Optional power adapter
Resolving a low battery level when a charged battery is available
1.
Turn off the computer or initiate Hibernation.
2.
Remove the discharged battery, and then insert a charged battery.
3.
Turn on the computer.
Resolving a low battery level when no power source is available
▲
Initiate Hibernation.
– or –
Save your work and shut down the computer.
Resolving a low battery level when the computer cannot exit Hibernation
When the computer lacks sufficient power to exit Hibernation, follow these steps:
1.
Insert a charged battery or plug the computer into external power.
2.
Exit Hibernation by briefly press the power button.
Calibrating a battery
Calibrate a battery under the following conditions:
● When battery charge displays seem inaccurate
●
When you observe a significant change in battery run time
Even if a battery is heavily used, it should not need to be calibrated more than once a month. It is also not necessary to calibrate a new battery.
Step 1: Fully charge the battery
WARNING!
Do not charge the computer battery while you are onboard aircraft.
NOTE:
The battery charges whether the computer is off or in use, but it charges faster when the computer is off.
80 Chapter 5 Power management
To fully charge the battery:
1.
Insert the battery into the computer.
2.
Connect the computer to an AC adapter, optional power adapter, optional expansion product, or optional docking device, and then plug the adapter or device into external power.
The battery light on the computer turns on.
3.
Leave the computer plugged into external power until the battery is fully charged.
The battery light on the computer turns off.
Step 2: Disable Hibernation and Sleep
1.
Click the battery meter icon in the notification area, and then click More power options.
– or –
Select Start > Control Panel > System and Maintenance > Power Options.
2.
Under the current power plan, click Change plan settings.
3.
Record the Turn off the display and Put the computer to sleep settings listed in the On
battery column so that you can reset them after the calibration.
4.
Change the Turn off the display and Put the computer to sleep settings to Never.
5.
Click Change advanced power settings.
6.
Click the plus sign next to Sleep, and then click the plus sign next to Hibernate after.
7.
Record the On battery setting under Hibernate after so that you can reset it after the calibration.
8.
Change the On battery setting to Never.
9.
Click OK.
10.
Click Save changes.
Step 3: Discharge the battery
The computer must remain on while the battery is being discharged. The battery can discharge whether or not you are using the computer, but the battery will discharge faster while you are using it.
●
If you plan to leave the computer unattended during the discharge, save your information before beginning the discharge procedure.
●
If you use the computer occasionally during the discharge procedure and have set energy-saving timeouts, expect the following performance from the system during the discharge process:
◦
The monitor will not turn off automatically.
◦
Hard drive speed will not decrease automatically when the computer is idle.
◦
System-initiated Hibernation will not occur.
Using battery power 81
To discharge a battery:
1.
Unplug the computer from its external power source, but do not turn off the computer.
2.
Run the computer on battery power until the battery is discharged. The battery light begins to blink when the battery has discharged to a low battery level. When the battery is discharged, the battery light turns off and the computer shuts down.
82 Chapter 5 Power management
Step 4: Fully recharge the battery
To recharge the battery:
1.
Plug the computer into external power and maintain external power until the battery is fully recharged. When the battery is recharged, the battery light on the computer turns off.
You can use the computer while the battery is recharging, but the battery will charge faster if the computer is off.
2.
If the computer is off, turn it on when the battery is fully charged and the battery light has turned off.
Step 5: Reenable Hibernation and Sleep
CAUTION:
Failure to reenable Hibernation after calibration may result in a full battery discharge and information loss if the computer reaches a critical battery level.
1.
Click the battery meter icon in the notification area, and then click More power options.
– or –
Select Start > Control Panel > System and Maintenance > Power Options.
2.
Under the current power plan, click Change plan settings.
3.
Reenter the settings that you recorded for the items in the On battery column.
4.
Click Change advanced power settings.
5.
Click the plus sign next to Sleep, and then click the plus sign next to Hibernate after.
6.
Reenter the setting that you recorded for On battery.
7.
Click OK.
8.
Click Save changes.
Conserving battery power
● Select low power-use settings through Power Options in Windows Control Panel.
●
Turn off wireless and local area network (LAN) connections and exit modem applications when you are not using them.
● Disconnect external devices that are not plugged into an external power source, when you are not using them.
●
Stop, disable, or remove any external media cards that you are not using.
● Use the fn+f9 and fn+f10 hotkeys to adjust screen brightness as needed.
●
If you leave your work, initiate Sleep or Hibernation, or shut down the computer.
Storing a battery
CAUTION:
To prevent damage to a battery, do not expose it to high temperatures for extended periods of time.
Using battery power 83
If a computer will be unused and unplugged from external power for more than 2 weeks, remove the battery and store it separately.
To prolong the charge of a stored battery, place it in a cool, dry place.
NOTE:
A stored battery should be checked every 6 months. If the capacity is less than 50 percent, recharge the battery before returning it to storage.
Calibrate a battery before using it if it has been stored for one month or more.
Disposing of a used battery
WARNING!
To reduce the risk of fire or burns, do not disassemble, crush, or puncture; do not short external contacts; do not dispose of in fire or water.
Refer to the Regulatory, Safety and Environmental Notices for battery disposal information.
Replacing the battery
Computer battery life varies, depending on the power management settings, programs running on the computer, display brightness, external devices connected to the computer, and other factors.
Battery Check notifies you to replace the battery when an internal cell is not charging properly, or when the battery storage capacity has reached a “weak” condition. A message refers you to the HP Web site for more information about ordering a replacement battery. If the battery is possibly covered by an HP warranty, instructions include a warranty ID.
NOTE:
To ensure that you always have battery power when you need it, HP recommends purchasing a new battery when the storage capacity indicator turns green-yellow.
84 Chapter 5 Power management
Testing an AC adapter
Test the AC adapter if the computer exhibits any of the following symptoms:
●
The computer will not turn on when connected to the AC adapter.
●
The display does not turn on when the computer is connected to the AC adapter and external power.
●
The power light is off when the computer is connected to the AC adapter.
To test the AC adapter:
1.
Remove the battery from the computer.
2.
Connect the AC adapter to the computer and to an AC outlet.
3.
Turn on the computer.
●
If the power light turns on, the AC adapter is functioning properly.
●
If the power light remains off, the AC adapter is not functioning and should be replaced.
Contact technical support for information on obtaining a replacement AC power adapter. Select
Start > Help and Support > Get assistance.
Shutting down the computer
CAUTION:
Unsaved information will be lost when the computer is shut down.
The Shut Down command closes all open programs, including the operating system, and then turns off the display and computer.
Shut down the computer under any of the following conditions:
●
When you need to replace the battery or access components inside the computer
● When you are connecting an external hardware device that does not connect to a USB port
●
When the computer will be unused and disconnected from external power for an extended period
To shut down the computer, follow these steps:
NOTE:
If the computer is in the Sleep state or in Hibernation, you must first exit Sleep or Hibernation before shutdown is possible.
1.
Save your work and close all open programs.
2.
Click Start, and then click the arrow next to the Lock button.
3.
Click Shut Down.
Testing an AC adapter 85
If the computer is unresponsive and you are unable to use the preceding shutdown procedures, try the following emergency procedures in the sequence provided:
●
Press ctrl+alt+delete , and then press the power button.
●
Press and hold the power button for at least 5 seconds.
● Disconnect the computer from external power and remove the battery.
86 Chapter 5 Power management
6 Drives
Identifying installed drives
Your computer includes a hard drive (with a rotating disc) or a solid-state drive (SSD) with solid-state memory. Because it has no moving parts, an SSD does not generate as much heat as a hard drive.
To view the drives installed on the computer, select Start > Computer.
NOTE:
Windows includes the User Account Control feature to improve the security of your computer.
You may be prompted for your permission or password for tasks such as installing applications, running utilities, or changing Windows settings. Refer to Help and Support for more information.
Handling drives
Drives are fragile computer components that must be handled with care. Refer to the following cautions before handling drives. Additional cautions are included with the procedures to which they apply.
Identifying installed drives 87
CAUTION:
To reduce the risk of damage to the computer, damage to a drive, or loss of information, observe these precautions:
Before you move a computer that is connected to an external hard drive, initiate Sleep and allow the screen to clear, or properly disconnect the external hard drive.
Before handling a drive, discharge static electricity by touching the unpainted metal surface of the drive.
Do not touch the connector pins on a removable drive or on the computer.
Handle a drive carefully; do not drop a drive or place items on it.
Before removing or inserting a drive, shut down the computer. If you are unsure whether the computer is off, in the Sleep state, or in Hibernation, turn the computer on and then shut it down through the operating system.
Do not use excessive force when inserting a drive into a drive bay.
Do not type on the keyboard or move the computer while an optional optical drive is writing to a disc.
The write process is sensitive to vibration.
When the battery is the only source of power, be sure that the battery is sufficiently charged before writing to media.
Avoid exposing a drive to temperature or humidity extremes.
Avoid exposing a drive to liquids. Do not spray the drive with cleaning products.
Remove media from a drive before removing the drive from the drive bay, or traveling with, shipping, or storing a drive.
If a drive must be mailed, place the drive in a bubble-pack mailer or other suitable protective packaging and label the package “FRAGILE.”
Avoid exposing a drive to magnetic fields. Security devices with magnetic fields include airport walkthrough devices and security wands. The airport security devices that check carry-on luggage, such as conveyor belts, use X-rays instead of magnetism and will not damage a drive.
88 Chapter 6 Drives
Improving hard drive performance
Using Disk Defragmenter
As you use the computer, files on the hard drive become fragmented. Disk Defragmenter consolidates the fragmented files and folders on the hard drive so that the system can run more efficiently.
After you start Disk Defragmenter, it works without supervision. Depending on the size of your hard drive and the number of fragmented files, Disk Defragmenter may take more than an hour to complete. You may want to set it to run during the night or another time when you do not need access to your computer.
HP recommends defragmenting your hard drive at least once a month. You may set Disk Defragmenter to run on a monthly schedule, but you can defragment your computer manually at any time.
NOTE:
It is not necessary to run Disk Defragmenter on solid-state drives.
To run Disk Defragmenter:
1.
Select Start > All Programs > Accessories > System Tools > Disk Defragmenter.
2.
Click Defragment now.
NOTE:
Windows includes the User Account Control feature to improve the security of your computer. You may be prompted for your permission or password for tasks such as installing software, running utilities, or changing Windows settings. Refer to Help and Support for more information.
For additional information, access the Disk Defragmenter software Help.
Using Disk Cleanup
Disk Cleanup searches the hard drive for unnecessary files that you can safely delete to free up disk space and help the computer to run more efficiently.
To run Disk Cleanup:
1.
Select Start > All Programs > Accessories > System Tools > Disk Cleanup.
2.
Follow the on-screen instructions.
Improving hard drive performance 89
Using HP 3D DriveGuard
HP 3D DriveGuard protects the hard drive by parking the drive and halting I/O requests under either of the following conditions:
●
You drop the computer.
●
You move the computer with the display closed while the computer is running on battery power.
A short time after the end of one of these events, HP 3D DriveGuard returns the hard drive to normal operation.
NOTE:
Because solid-state drives (SSD) lack moving parts, HP 3D DriveGuard is unnecessary.
NOTE:
If the upgrade bay contains a hard drive, the hard drive is protected by HP 3D DriveGuard.
Hard drives installed in optional docking devices or connected to USB ports are not protected by HP 3D
DriveGuard.
For more information, refer to the HP 3D DriveGuard software Help.
Identifying HP 3D DriveGuard status
The drive light on the computer changes to an amber color to show that the drive is parked. To determine whether drives are currently protected or whether a drive is parked, use Mobility Center:
●
If the software is enabled, a green check mark is superimposed over the hard drive icon.
●
If the software is disabled, a red X is superimposed over the hard drive icon.
● If the drives are parked, a yellow moon is superimposed over the hard drive icon.
NOTE:
The icon in the Mobility Center may not show the most up-to-date status for the drive. For immediate updates after a change in status, you need to enable the notification area icon.
To enable the notification area icon:
1.
Select Start > Control Panel > Hardware and Sound > HP 3D DriveGuard.
2.
Next to Icon in System Tray row, click Show.
3.
Click OK.
If HP 3D DriveGuard has parked the drive, the computer will behave in the following ways:
● The computer will not shut down.
●
The computer will not initiate Sleep or Hibernation, except as described in the following Note.
NOTE:
If the computer is running on battery power and reaches a critical battery level, HP 3D
DriveGuard allows the computer to initiate Hibernation.
●
The computer will not activate battery alarms set on the Alarms tab in Power Options properties.
Before you move the computer, HP recommends that you either shut it down or initiate Sleep or
Hibernation.
90 Chapter 6 Drives
Using HP 3D DriveGuard software
The HP 3D DriveGuard software enables you to perform the following tasks:
●
Enable and disable HP 3D DriveGuard.
NOTE:
Permission to enable or disable HP 3D DriveGuard is dependent on certain user privileges. Members of an Administrator group can change privileges for non-Administrator users.
● Determine whether a drive in the system is supported.
To open the software and change settings, follow these steps:
1.
In Mobility Center, click the hard drive icon to open the HP 3D DriveGuard window.
– or –
Select Start > Control Panel > Hardware and Sound > HP 3D DriveGuard.
If prompted by User Account Control, click Yes.
2.
Click the appropriate button to change settings.
3.
Click OK.
Using HP 3D DriveGuard 91
Replacing a hard drive in the hard drive bay
CAUTION:
To prevent information loss or an unresponsive system:
Shut down the computer before removing the hard drive from the hard drive bay. Do not remove the hard drive while the computer is on, in the Sleep state, or in Hibernation.
If you are not sure whether the computer is off or in Hibernation, turn the computer on by briefly pressing the power button. Then shut down the computer through the operating system.
To remove a hard drive:
1.
Save your work.
2.
Shut down the computer and close the display.
3.
Disconnect all external hardware devices connected to the computer.
4.
Unplug the power cord from the AC outlet.
5.
Turn the computer upside down on a flat surface, with the battery bay toward you.
6.
Remove the battery from the computer.
7.
Loosen the 2 hard drive cover screws (1).
8.
Remove the hard drive cover (2).
9.
Loosen the hard drive screw (1).
10.
Pull the hard drive tab to the right (2) to disconnect the hard drive.
92 Chapter 6 Drives
11.
Lift the hard drive (3) out of the hard drive bay.
To install a hard drive:
1.
Insert the hard drive into the hard drive bay (1).
2.
Pull the hard drive tab (2) to the left to connect the hard drive.
3.
Tighten the hard drive screw (3).
4.
Align the tabs (1) on the hard drive cover with the notches on the computer.
5.
Replace the cover (2).
Replacing a hard drive in the hard drive bay 93
6.
Tighten the hard drive cover screws (3).
7.
Replace the battery.
8.
Turn the computer right-side up, and then reconnect external power and external devices.
9.
Turn on the computer.
94 Chapter 6 Drives
Replacing a drive in the upgrade bay
The upgrade bay can hold either a hard drive or an optical drive.
Removing the protective insert
The upgrade bay may contain a protective insert. You must remove the insert before inserting a drive into the upgrade bay. To remove the insert:
1.
Save your work.
2.
Shut down the computer and close the display.
3.
Disconnect all external hardware devices connected to the computer.
4.
Unplug the power cord from the AC outlet.
5.
Turn the computer upside down on a flat surface, with the upgrade bay toward you.
6.
Loosen the upgrade bay screw (1).
7.
Using a flat-bladed screwdriver, gently push the tab to release the optical drive (2).
8.
Remove the protective insert (3) from the upgrade bay.
Replacing a hard drive
CAUTION:
To prevent information loss or an unresponsive system:
Shut down the computer before removing the hard drive from the upgrade bay. Do not remove the hard drive while the computer is on, in the Sleep state, or in Hibernation.
If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the power button. Then shut down the computer through the operating system.
To remove a hard drive from the upgrade bay:
1.
Save your work.
2.
Shut down the computer and close the display.
Replacing a drive in the upgrade bay 95
3.
Disconnect all external hardware devices connected to the computer.
4.
Unplug the power cord from the AC outlet.
5.
Turn the computer upside down on a flat surface, with the upgrade bay toward you.
6.
Remove the battery from the computer.
7.
Remove the protective screw caps (1), and then remove the 4 hard drive screws (2).
8.
Loosen the upgrade bay screw (1).
9.
Using a flat-bladed screwdriver, gently push the tab to release the hard drive (2).
96 Chapter 6 Drives
10.
Remove the hard drive from the upgrade bay.
To install a hard drive in the upgrade bay:
1.
Insert the hard drive into the upgrade bay.
2.
Tighten the upgrade bay screw.
Replacing a drive in the upgrade bay 97
3.
Replace the 4 hard drive screws (1), and then replace the protective screw caps (2).
4.
Replace the battery.
5.
Turn the computer right-side up, and then reconnect external power and external devices.
6.
Turn on the computer.
Replacing an optical drive
CAUTION:
To prevent information loss or an unresponsive system:
Shut down the computer before removing the optical drive from the upgrade bay. Do not remove the optical drive while the computer is on, in the Sleep state, or in Hibernation.
If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the power button. Then shut down the computer through the operating system.
To remove an optical drive from the upgrade bay:
1.
Save your work.
2.
Shut down the computer and close the display.
3.
Disconnect all external hardware devices connected to the computer.
4.
Unplug the power cord from the AC outlet.
5.
Turn the computer upside down on a flat surface, with the upgrade bay toward you.
6.
Remove the battery from the computer.
7.
Loosen the upgrade bay screw (1).
98 Chapter 6 Drives
8.
Using a flat-bladed screwdriver, gently push the tab to release the optical drive (2).
9.
Remove the optical drive from the upgrade bay.
To install an optical drive in the upgrade bay:
1.
Insert the optical drive into the upgrade bay.
Replacing a drive in the upgrade bay 99
2.
Tighten the upgrade bay screw.
3.
Replace the battery.
4.
Turn the computer right-side up, and then reconnect external power and external devices.
5.
Turn on the computer.
100 Chapter 6 Drives
7 External devices
Using a USB device
Universal Serial Bus (USB) is a hardware interface that can be used to connect an optional external device, such as a USB keyboard, mouse, drive, printer, scanner, or hub.
Some USB devices may require additional support software, which is usually included with the device.
For more information about device-specific software, refer to the manufacturer's instructions.
Your computer model has 4 USB ports, which support USB 1.0, USB 1.1, and USB 2.0 devices.
An optional docking device or a USB hub provide additional USB ports that can be used with the computer.
Connecting a USB device
CAUTION:
To prevent damage to a USB connector, use minimal force to connect a USB device.
▲
To connect a USB device to the computer, connect the USB cable for the device to the USB port.
You will hear a sound when the device has been detected.
NOTE:
The first time you connect a USB device, a message is displayed in the notification area to let you know the device is recognized by the computer.
Using a USB device 101
Stopping and removing a USB device
CAUTION:
To prevent loss of information or an unresponsive system, stop a USB device before removing it.
CAUTION:
To prevent damage to a USB connector, do not pull on the cable to remove the USB device.
To stop and remove a USB device:
1.
Double-click the Safely Remove Hardware icon in the notification area, at the far right of the taskbar.
NOTE:
To display the Safely Remove Hardware icon, click the Show Hidden Icons icon (< or
<<) in the notification area.
2.
Click the name of the device in the list.
NOTE:
If the USB device is not listed, you do not have to stop the device before you remove it.
3.
Click Stop, and then click OK.
4.
Remove the device.
Using USB legacy support
USB legacy support (enabled at the factory) permits the following actions:
●
Using a USB keyboard, mouse, or hub connected to a USB port on the computer during startup or in an MS-DOS-based program or utility
● Starting or restarting from an optional external MultiBay or an optional USB bootable device
To disable or reenable USB legacy support in Computer Setup, follow these steps:
1.
Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen.
2.
Press f10 to enter Computer Setup.
3.
Use a pointing device or the arrow keys to select System Configuration, and then select Device
Configurations.
4.
To disable USB legacy support, click Disabled next to USB legacy support. To reenable USB legacy support, click Enabled next to USB legacy support.
5.
To save your changes and exit Computer Setup, click Save in the lower-left corner of the screen, and then follow the on-screen instructions.
– or –
Use the arrow keys to select File > Save changes and exit, and then follow the on-screen instructions.
Your changes go into effect when the computer restarts.
102 Chapter 7 External devices
Using a 1394 device
IEEE 1394 is a hardware interface that connects a high-speed multimedia or data storage device to the computer. Scanners, digital cameras, and digital camcorders often require a 1394 connection.
Some 1394 devices may require additional support software, which is usually included with the device.
For more information about device-specific software, refer to the manufacturer's instructions.
The 1394 port also supports IEEE 1394a devices.
Connecting a 1394 device
CAUTION:
To prevent damage to a 1394 port connector, use minimal force when connecting a 1394 device.
▲
To connect a 1394 device to the computer, connect the 1394 cable for the device to the 1394 port.
You will hear a sound when the device has been detected.
Stopping and removing a 1394 device
CAUTION:
To prevent loss of information or an unresponsive system, stop the 1394 device before removing it.
CAUTION:
To prevent damage to a 1394 connector, do not pull on the cable to remove the 1394 device.
1.
Double-click the Safely Remove Hardware icon in the notification area, at the far right of the taskbar.
NOTE:
To display the Safely Remove Hardware icon, click the Show Hidden Icons icon (< or
<<) in the notification area.
2.
Click the name of the device in the list.
NOTE:
If the device is not listed, you do not have to stop the device before you remove it.
Using a 1394 device 103
3.
Click Stop, and then click OK.
4.
Remove the device.
104 Chapter 7 External devices
Using a serial device (select models only)
Select computer models include a serial port that connects optional devices such as a serial modem, mouse, or printer.
Some serial devices may require additional support software, which is usually included with the device.
For more information about device-specific software, refer to the manufacturer's instructions.
▲
To connect a serial device, connect the device cable to the serial port on the computer.
Using a serial device (select models only) 105
Using external drives
Removable external drives expand your options for storing and accessing information. A USB drive can be added by connecting the drive to a USB port on the computer.
USB drives include the following types:
●
1.44-megabyte diskette drive
●
Hard drive module (a hard drive with an adapter attached)
●
DVD-ROM Drive
●
DVD/CD-RW Combo Drive
● DVD±RW/CD-RW Combo Drive
Using optional external devices
NOTE:
For more information about required software and drivers, or to learn which computer port to use, refer to the manufacturer's instructions.
To connect an external device to the computer:
CAUTION:
To reduce the risk of damage to the equipment when connecting a powered device, be sure that the device is turned off and the AC power cord is unplugged.
1.
Connect the device to the computer.
2.
If you are connecting a powered device, plug the device power cord into a grounded AC outlet.
3.
Turn on the device.
To disconnect an unpowered external device, turn off the device, and then disconnect it from the computer. To disconnect a powered external device, turn off the device, disconnect it from the computer, and then unplug the AC power cord.
106 Chapter 7 External devices
Using a docking device
The docking connector connects the computer to an optional docking device. An optional docking device provides additional ports and connectors that can be used with the computer.
Using a docking device 107
8 External media cards
Using Media Card Reader cards
Optional digital cards provide secure data storage and convenient data sharing. These cards are often used with digital media–equipped cameras and PDAs as well as with other computers.
The Media Card Reader supports the following formats:
●
Memory Stick
●
Memory Stick Pro
●
Memory Stick Duo (adapter required)
●
Memory Stick Duo Pro (adapter required)
●
MultiMediaCard
● MultiMediaCard Plus
●
Secure Digital (SD) Memory Card
●
Secure Digital (SD) High Capacity Memory Card
● micro Secure Digital (SD) Memory Card (adapter required)
● xD-Picture Card
Inserting a digital card
CAUTION:
To prevent damage to the digital card connectors, use minimal force to insert a digital card.
1.
Hold the digital card label-side up, with the connectors facing the computer.
108 Chapter 8 External media cards
2.
Insert the card into the Media Card Reader, and then push in on the card until it is firmly seated.
You will hear a sound when the device has been detected, and a menu of available options may be displayed.
Stopping and removing a digital card
CAUTION:
To prevent loss of data or an unresponsive system, stop a digital card before removing it.
1.
Save your information and close all programs associated with the digital card.
NOTE:
To stop a data transfer, click Cancel in the operating system Copying window.
2.
Stop the digital card:
a.
Double-click the Safely Remove Hardware icon in the notification area, at the far right of the taskbar.
NOTE:
To display the Safely Remove Hardware icon, click the Show Hidden Icons icon
(< or <<) in the notification area.
b.
Click the name of the digital card in the list.
c.
Click Stop, and then click OK.
3.
Press in on the digital card (1), and then remove the card from the slot (2).
Using Media Card Reader cards 109
Using ExpressCards (select models only)
An ExpressCard is a high-performance PC Card that is inserted into the ExpressCard slot.
Like standard PC Cards, ExpressCards are designed to conform to the standard specifications of the
Personal Computer Memory Card International Association (PCMCIA).
Configuring an ExpressCard
Install only the software required for your device. If you are instructed by the ExpressCard manufacturer to install device drivers:
●
Install only the device drivers for your operating system.
●
Do not install other software, such as card services, socket services, or enablers, supplied by the
ExpressCard manufacturer.
Inserting an ExpressCard
CAUTION:
To prevent damage to the computer and external media cards, do not insert a PC Card into an ExpressCard slot.
CAUTION:
To prevent damage to the connectors:
Use minimal force when inserting an ExpressCard.
Do not move or transport the computer when an ExpressCard is in use.
The ExpressCard slot may contain a protective insert. To remove the insert:
1.
Press in on the insert (1) to unlock it.
2.
Pull the insert out of the slot (2).
To insert an ExpressCard:
1.
Hold the card label-side up, with the connectors facing the computer.
110 Chapter 8 External media cards
2.
Insert the card into the ExpressCard slot, and then push in on the card until it is firmly seated.
You will hear a sound when the device has been detected, and a menu of options may be displayed.
NOTE:
The first time you insert an ExpressCard, a message is displayed in the notification area to let you know the device is recognized by the computer.
NOTE:
An inserted ExpressCard uses power even when idle. To conserve power, stop or remove an
ExpressCard when it is not in use.
Stopping and removing an ExpressCard
CAUTION:
To prevent loss of data or an unresponsive system, stop an ExpressCard before removing it.
1.
Save your information and close all programs associated with the ExpressCard.
NOTE:
To stop a data transfer, click Cancel in the operating system Copying window.
2.
Stop the ExpressCard:
a.
Double-click the Safely Remove Hardware icon in the notification area, at the far right of the taskbar.
NOTE:
To display the Safely Remove Hardware icon, click the Show Hidden Icons icon
(< or <<) in the notification area.
b.
Click the name of the ExpressCard in the list.
c.
Click Stop, and then click OK.
3.
Release and remove the ExpressCard:
a.
Gently press in on the ExpressCard (1) to unlock it.
b.
Pull the ExpressCard out of the slot (2).
Using ExpressCards (select models only) 111
112 Chapter 8 External media cards
Using Smart Cards (select models only)
NOTE:
The term smart card is used throughout this chapter to refer to both smart cards and Java™
Cards.
A smart card is a credit card–sized accessory that carries a microchip containing memory and a microprocessor. Like personal computers, smart cards have an operating system to manage input and output, and they include security features to protect against tampering. Industry-standard smart cards are used with the smart card reader (select models only).
A personal identification number (PIN) is needed to gain access to the contents of the microchip. For more information about smart card security features, refer to Help and Support.
NOTE:
Your computer may look slightly different from the illustrations in this chapter.
Inserting a smart card
To insert a smart card:
1.
Holding the smart card label-side up, gently slide the card into the smart card reader until the card is seated.
2.
Follow the on-screen instructions for logging on to the computer using the smart card PIN.
Removing a smart card
To remove a smart card:
▲
Grasp the edge of the smart card, and pull it out of the smart card reader.
Using Smart Cards (select models only) 113
9 Memory modules
The computer has two memory module compartments. The primary memory module compartment is located under the keyboard. The expansion memory module compartment is located on the bottom of the computer.
The memory capacity of the computer can be upgraded by adding a memory module to the empty expansion memory module slot or by upgrading the existing memory module in the primary memory module slot.
WARNING!
To reduce the risk of electric shock and damage to the equipment, unplug the power cord and remove all batteries before installing a memory module.
CAUTION:
Electrostatic discharge (ESD) can damage electronic components. Before beginning any procedure, touch a grounded metal object to be sure that you are discharged of static electricity.
114 Chapter 9 Memory modules
Adding or replacing a memory module in the expansion memory module slot
To add or replace a memory module in the expansion memory module slot, follow these steps:
1.
Save your work.
2.
Shut down the computer and close the display.
If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the power button. Then shut down the computer through the operating system.
3.
Disconnect all external devices connected to the computer.
4.
Unplug the power cord from the AC outlet.
5.
Turn the computer upside down on a flat surface.
6.
Remove all batteries from the computer.
7.
Loosen the memory module compartment cover screw (1).
8.
Lift the memory module compartment cover (2) away from the computer.
9.
Remove the memory module:
NOTE:
If the expansion memory module slot is not populated, bypass step 9 and proceed to step
10.
a.
Pull away the retention clips (1) on each side of the memory module.
The memory module tilts up.
CAUTION:
To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module.
Adding or replacing a memory module in the expansion memory module slot 115
b.
Grasp the edge of the memory module (2), and gently pull the module out of the memory module slot.
To protect a memory module after removal, place it in an electrostatic-safe container.
10.
Insert a memory module:
a.
Align the notched edge (1) of the memory module with the tab in the memory module slot.
CAUTION:
To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module and do not bend the memory module.
b.
With the memory module at a 45-degree angle from the surface of the memory module compartment, press the module (2) into the memory module slot until it is seated.
c.
Gently press the memory module (3) down, applying pressure to both the left and right edges of the memory module, until the retention clips snap into place.
11.
Align the tabs (1) on the memory module compartment cover with the notches on the computer.
12.
Close the cover (2).
116 Chapter 9 Memory modules
13.
Tighten the memory module compartment cover screw (3).
14.
Replace the batteries.
15.
Turn the computer right-side up, and then reconnect external power and external devices.
16.
Turn on the computer.
Adding or replacing a memory module in the expansion memory module slot 117
Upgrading a memory module in the primary memory module slot
To upgrade a memory module in the primary memory module slot, follow these steps:
1.
Save your work.
2.
Shut down the computer.
If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the power button. Then shut down the computer through the operating system.
3.
Disconnect all external devices connected to the computer.
4.
Unplug the power cord from the AC outlet.
5.
Turn the computer upside down on a flat surface.
6.
Remove all batteries from the computer.
7.
Loosen the 3 keyboard access screws.
8.
Turn the computer over and open it.
9.
Slide the 4 keyboard release latches (1) to release the keyboard.
118 Chapter 9 Memory modules
10.
Gently lift the top edge of the keyboard (2) and tilt the keyboard over until it rests on the palm rest of the computer.
11.
Remove the memory module:
a.
Pull away the retention clips (1) on each side of the memory module.
The memory module tilts up.
CAUTION:
To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module.
b.
Grasp the edge of the memory module (2), and gently pull the module out of the memory module slot.
To protect a memory module after removal, place it in an electrostatic-safe container.
Upgrading a memory module in the primary memory module slot 119
12.
Insert a memory module:
a.
Align the notched edge (1) of the memory module with the tab in the memory module slot.
CAUTION:
To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module and do not bend the memory module.
b.
With the memory module at a 45-degree angle from the surface of the memory module compartment, press the module (2) into the memory module slot until it is seated.
c.
Gently press the memory module (3) down, applying pressure to both the left and right edges of the memory module, until the retention clips snap into place.
13.
Replace the keyboard (1).
14.
Slide the 4 keyboard release latches (2) to lock the keyboard.
15.
Close the cover.
16.
Turn the computer upside down on a flat surface.
120 Chapter 9 Memory modules
17.
Tighten the 3 keyboard access screws.
18.
Replace the batteries.
19.
Turn the computer right-side up, and then reconnect external power and external devices.
20.
Turn on the computer.
Upgrading a memory module in the primary memory module slot 121
10 Security
Protecting the computer
NOTE:
Security solutions are designed to act as deterrents. These deterrents may not prevent a product from being mishandled or stolen.
NOTE:
In some countries or regions, the computer supports CompuTrace, which is an online securitybased tracking and recovery service. If the computer is stolen, CompuTrace can track the computer if the unauthorized user accesses the Internet. You must purchase the software and subscribe to the service in order to use CompuTrace. For information about ordering the CompuTrace software, go to the HP Web site at http://www.hpshopping.com
.
Security features provided with your computer can protect the computer, personal information, and data from a variety of risks. The way you use your computer will determine which security features you need to use.
The Windows® operating system offers certain security features. Additional security features are listed in the following table. Most of these additional security features can be configured in the Computer Setup utility (referred to hereafter as Computer Setup).
To protect against Use this security feature
Unauthorized use of the computer
Unauthorized access to Computer Setup ( f10 )
Unauthorized access to the contents of a hard drive
Unauthorized startup from an optical drive, diskette drive, or internal network adapter
HP ProtectTools Security Manager, in combination with a password, smart card, and/or fingerprint reader
BIOS administrator password in Computer Setup*
DriveLock password in Computer Setup*
Boot options feature in Computer Setup*
Unauthorized access to a Windows user account
Unauthorized access to data
HP ProtectTools Security Manager
●
Firewall software
● Windows updates
●
Drive Encryption for HP ProtectTools
BIOS administrator password in Computer Setup* Unauthorized access to Computer Setup settings and other system identification information
Unauthorized removal of the computer Security cable slot (used with an optional security cable)
*Computer Setup is a preinstalled, ROM-based utility that can be used even when the operating system is not working or will not load. You can use either a pointing device (TouchPad, pointing stick, or USB mouse) or the keyboard to navigate and make selections in Computer Setup.
122 Chapter 10 Security
Using passwords
Most security features use passwords. Whenever you set a password, write down the password and store it in a secure location away from the computer. Note the following password considerations:
●
Setup and DriveLock passwords are set in Computer Setup and are managed by the system BIOS.
●
The embedded security password, which is an HP ProtectTools Security Manager password, can be enabled in Computer Setup to provide BIOS password protection in addition to their normal HP
ProtectTools functions. The embedded security password is used with the optional embedded security chip.
●
Windows passwords are set only in the Windows operating system.
●
If you forget the BIOS administrator password set in Computer Setup, you can use HP SpareKey to access the utility.
●
If you forget both the DriveLock user password and the DriveLock master password set in Computer
Setup, the hard drive that is protected by the passwords is permanently locked and can no longer be used.
You can use the same password for a Computer Setup feature and for a Windows security feature. You can also use the same password for more than one Computer Setup feature.
Use the following tips for creating and saving passwords:
● When creating passwords, follow requirements set by the program.
●
Write down your passwords and store them in a secure place away from the computer.
●
Do not store passwords in a file on the computer.
The following tables list commonly used Windows and BIOS administrator passwords and describe their functions.
Setting passwords in Windows
Windows passwords Function
Administrator password*
User password*
Protects access to a Windows administrator-level account.
Protects access to a Windows user account.
*For information about setting a Windows administrator password or a Windows user password, select Start > Help and
Support.
Setting passwords in Computer Setup
BIOS administrator passwords
BIOS administrator password
DriveLock master password
Function
Protects access to Computer Setup.
Protects access to the internal hard drive that is protected by
DriveLock. It is also used to remove DriveLock protection. This password is set under DriveLock Passwords during the enable process.
Using passwords 123
BIOS administrator passwords
DriveLock user password
TPM embedded security password
Function
Protects access to the internal hard drive that is protected by
DriveLock, and is set under DriveLock Passwords during the enable process.
When enabled as a BIOS administrator password, protects access to the computer contents when the computer turns on, restarts, or exits Hibernation.
This password requires the optional embedded security chip to support this security feature.
BIOS administrator password
The Computer Setup BIOS administrator password protects the configuration settings and system identification information in Computer Setup. After this password is set, it must be entered to access
Computer Setup and to make changes using Computer Setup.
Note the following characteristics of the BIOS administrator password:
●
It is not interchangeable with a Windows administrator password, although both passwords can be identical.
● It is not displayed as it is set, entered, changed, or deleted.
●
It must be set and entered with the same keys. For example, a BIOS administrator password set with keyboard number keys will not be recognized if you enter it thereafter with embedded numeric keypad number keys.
● It can include any combination of up to 32 letters and numbers and it is not case sensitive unless mandated by the administrator.
124 Chapter 10 Security
Managing a BIOS administrator password
A BIOS administrator password is set, changed, and deleted in Computer Setup.
To set or change this password in Computer Setup, follow these steps:
1.
Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen.
2.
Press f10 to enter BIOS Setup.
3.
Use a pointing device or the arrow keys to select Security > Change Password, and then press enter .
4.
When prompted, type your current password.
5.
When prompted, type your new password.
6.
When prompted, type your new password again to confirm.
7.
To save your changes and exit Computer Setup, click Save in the lower-left corner of the screen, and then follow the on-screen instructions.
– or –
Use the arrow keys to select File > Save changes and exit, and then press enter .
Your changes go into effect when the computer restarts.
To delete this password in Computer Setup, follow these steps:
1.
Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen.
2.
Press f10 to enter BIOS Setup.
3.
Use a pointing device or the arrow keys to select Security > Change Password, and then press enter .
4.
When prompted, type your current password.
5.
When prompted for the new password, leave the field empty, and then press enter .
6.
Read the warning. To continue, select YES.
7.
When prompted to type your new password again, leave the field empty, and then press enter .
8.
To save your changes and exit Computer Setup, click Save in the lower-left corner of the screen, and then follow the on-screen instructions.
– or –
Use the arrow keys to select File > Save changes and exit, and then press enter .
Your changes go into effect when the computer restarts.
Using passwords 125
Entering a BIOS administrator password
At the BIOS administrator password prompt, type your password (using the same kind of keys you used to set the password), and then press enter . After 3 unsuccessful attempts to enter the BIOS administrator password, you must restart the computer and try again.
Using Computer Setup DriveLock
CAUTION:
To prevent the DriveLock-protected hard drive from becoming permanently unusable, record the DriveLock user password and the DriveLock master password in a safe place away from your computer. If you forget both DriveLock passwords, the hard drive will be permanently locked and can no longer be used.
DriveLock protection prevents unauthorized access to the contents of a hard drive. DriveLock can be applied only to the internal hard drive(s) of the computer. After DriveLock protection is applied to a drive, a password must be entered to access the drive. The drive must be inserted into the computer or an advanced port replicator in order for it to be accessed by the DriveLock passwords.
To apply DriveLock protection to an internal hard drive, a user password and a master password must be set in Computer Setup. Note the following considerations about using DriveLock protection:
●
After DriveLock protection is applied to a hard drive, the hard drive can be accessed only by entering either the user password or the master password.
● The owner of the user password should be the day-to-day user of the protected hard drive. The owner of the master password may be either a system administrator or the day-to-day user.
●
The user password and the master password can be identical.
● You can delete a user password or master password only by removing DriveLock protection from the drive. DriveLock protection can be removed from the drive only with the master password.
126 Chapter 10 Security
Setting a DriveLock password
To set a DriveLock password in Computer Setup, follow these steps:
1.
Turn on the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen.
2.
Press f10 to enter BIOS Setup.
3.
Use a pointing device or the arrow keys to select Security > DriveLock passwords, and then press enter .
4.
Use a pointing device to click the hard drive you want to protect.
– or –
Use the arrow keys to select the hard drive you want to protect, and then press enter .
5.
Read the warning. To continue, select YES.
6.
Type your master password in the New password and Verify new password fields, and then press enter .
7.
Type your user password in the New password and Verify new password fields, and then press enter .
8.
To confirm DriveLock protection on the drive you have selected, type DriveLock in the confirmation field, and then press enter .
NOTE:
The DriveLock confirmation is case sensitive.
9.
To save your changes and exit Computer Setup, click Save in the lower-left corner of the screen, and then follow the on-screen instructions.
– or –
Use the arrow keys to select File > Save changes and exit, and then press enter .
Your changes go into effect when the computer restarts.
Using passwords 127
Entering a DriveLock password
Be sure that the hard drive is inserted into the computer (not into an optional docking device or external
MultiBay).
At the DriveLock Password prompt, type your user or master password (using the same kind of keys you used to set the password), and then press enter .
After 2 incorrect attempts to enter the password, you must shut down the computer and try again.
128 Chapter 10 Security
Changing a DriveLock password
To change a DriveLock password in Computer Setup, follow these steps:
1.
Turn on the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen.
2.
Press f10 to enter BIOS Setup.
3.
Use a pointing device or the arrow keys to select Security > DriveLock passwords, and then press enter .
4.
Use a pointing device to select an internal hard drive.
– or –
Use the arrow keys to select an internal hard drive, and then press enter .
5.
Use a pointing device or the arrow keys to select the password you want to change.
6.
Type your current password in the Old password field, type a new password in the New
password and Verify new password fields, and then press enter .
7.
To save your changes and exit Computer Setup, click Save in the lower-left corner of the screen, and then follow the on-screen instructions.
– or –
Use the arrow keys to select File > Save changes and exit, and then press enter .
Your changes go into effect when the computer restarts.
Using passwords 129
Removing DriveLock protection
To remove DriveLock protection in Computer Setup, follow these steps:
1.
Turn on the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen.
2.
Press f10 to enter BIOS Setup.
3.
Use a pointing device or the arrow keys to select Security > DriveLock password, and then press enter .
4.
Use a pointing device or the arrow keys to select an internal hard drive, and then press enter .
5.
Use a pointing device or the arrow keys to select Disable protection.
6.
Type your master password, and then press enter .
7.
To save your changes and exit Computer Setup, click Save in the lower-left corner of the screen, and then follow the on-screen instructions.
– or –
Use the arrow keys to select File > Save changes and exit, and then press enter .
Your changes go into effect when the computer restarts.
Using Computer Setup Auto DriveLock
In a multiple-user environment, you can set an Automatic DriveLock password. When the Automatic
DriveLock password is enabled, a random user password and a DriveLock master password will be created for you. When any user passes the password credential, the same random user and DriveLock master password will be used to unlock the drive.
NOTE:
You must have a BIOS administrator password before you can access the Automatic
DriveLock features.
Entering an Automatic DriveLock password
To enable an Automatic DriveLock password in Computer Setup, follow these steps:
1.
Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen.
2.
Press f10 to enter BIOS Setup.
3.
Use a pointing device or the arrow keys to select Security > Automatic DriveLock, and then press enter .
4.
Use a pointing device or the arrow keys to select an internal hard drive, and then press enter .
5.
Read the warning. To continue, select YES.
6.
To save your changes and exit Computer Setup, click Save in the lower-left corner of the screen, and then follow the on-screen instructions.
– or –
Use the arrow keys to select File > Save changes and exit, and then press enter .
130 Chapter 10 Security
Removing Automatic DriveLock protection
To remove DriveLock protection in Computer Setup, follow these steps:
1.
Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen.
2.
Press f10 to enter BIOS Setup.
3.
Use a pointing device or the arrow keys to select Security > Automatic DriveLock, and then press enter .
4.
Use a pointing device or the arrow keys to select an internal hard drive, and then press enter .
5.
Use a pointing device or the arrow keys to select Disable protection.
6.
To save your changes and exit Computer Setup, click Save in the lower-left corner of the screen, and then follow the on-screen instructions.
– or –
Use the arrow keys to select File > Save changes and exit, and then press enter .
Using passwords 131
Using Computer Setup security features
Securing system devices
You can disable or enable system devices from the following menus in Computer Setup:
●
Boot Options
●
Device Configurations
●
Built-In Device Options
●
Port Options
To disable or reenable system devices in Computer Setup, follow these steps:
1.
Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen.
2.
Press f10 to enter BIOS Setup.
3.
Use a pointing device or the arrow keys to select System Configuration > Boot Options, or
System Configuration > Device Configurations or, System Configuration > Built-In Device
Options or System Configuration > Port Options.
4.
Press enter .
5.
To disable an option, use a pointing device to click Disabled next to the option.
– or –
Use the arrow keys to select Disabled next to the option, and then press enter .
6.
To reenable an option, use a pointing device to click Enabled next to the option.
– or –
Use the arrow keys to select Enabled next to the option, and then press enter .
7.
To save your changes and exit Computer Setup, click Save in the lower-left corner of the screen, and then follow the on-screen instructions.
– or –
Use the arrow keys to select File > Save changes and exit, and then press enter .
Your changes go into effect when the computer restarts.
Viewing Computer Setup System Information
The System Information feature in Computer Setup provides 2 types of system information:
●
Identification information about the computer model and the batteries
●
Specification information about the processor, cache, memory, ROM, video revision, and keyboard controller revision
132 Chapter 10 Security
To view this general system information in Computer Setup, follow these steps:
1.
Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen.
2.
Press f10 to enter BIOS Setup.
3.
Use a pointing device or the arrow keys to select File > System Information, and then press enter .
NOTE:
To prevent unauthorized access to this information, you must create a BIOS administrator password in Computer Setup.
Using Computer Setup System IDs
The System IDs feature in Computer Setup allows you to display or enter the computer asset tag and ownership tag.
NOTE:
To prevent unauthorized access to this information, you must create a BIOS administrator password in Computer Setup.
To manage this feature in Computer Setup, follow these steps:
1.
Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen.
2.
Press f10 to enter BIOS Setup.
3.
Use a pointing device or the arrow keys to select Security > System IDs, and then press enter .
4.
Use a pointing device or the arrow keys to select Notebook Asset Tag or Notebook Ownership
Tag, and then enter the information.
5.
Press enter when finished.
6.
To save your changes and exit Computer Setup, click Save in the lower-left corner of the screen, and then follow the on-screen instructions.
– or –
Use the arrow keys to select File > Save changes and exit, and then press enter .
Your changes go into effect when the computer restarts.
Using Computer Setup security features 133
Using antivirus software
When you use the computer to access e-mail, a network, or the Internet, you expose the computer to computer viruses. Computer viruses can disable the operating system, programs, or utilities, or cause them to function abnormally.
Antivirus software can detect most viruses, destroy them, and in most cases, repair any damage they have caused. To provide ongoing protection against newly discovered viruses, antivirus software must be kept up to date.
McAfee Total Protection antivirus software is either preinstalled or preloaded on the computer.
If the antivirus software is preinstalled, select Start > All Programs > McAfee > Managed
Services > Total Protection.
If the software is preloaded, select Start > All Programs > HP Software Setup, and then follow the on-screen instructions to load the McAfee Total Protection software.
For more information about computer viruses, type viruses in the Search box in Help and Support.
134 Chapter 10 Security
Using firewall software
When you use the computer to access e-mail, a network, or the Internet, unauthorized persons may be able to gain access to the computer, your personal files, and information about you. Use the firewall software preinstalled on the computer to protect your privacy. McAfee Total Protection antivirus software is preinstalled on the computer. To access your software, select Start > All Programs > McAfee >
Managing Services > Total Protection.
Firewall features include logging and reporting of network activity, and automatic monitoring of all incoming and outgoing traffic. For more information, refer to the software manufacturer’s instructions.
These instructions may be provided with the software, on disc, or on the manufacturer’s Web site.
NOTE:
Under some circumstances a firewall can block access to Internet games, interfere with printer or file sharing on a network, or block authorized e-mail attachments. To temporarily resolve the problem, disable the firewall, perform the task that you want to perform, and then reenable the firewall. To permanently resolve the problem, reconfigure the firewall as necessary, and adjust the policies and settings of other intrusion detection systems. For additional information, contact your network administrator or IT department.
Using firewall software 135
Installing critical updates
CAUTION:
Microsoft sends alerts regarding critical updates. To protect the computer from security breaches and computer viruses, install all critical updates from Microsoft as soon as you receive an alert.
Updates to the operating system and other software may have become available after the computer was shipped. To be sure that all available updates are installed on the computer, observe these guidelines:
●
Run Windows Update monthly to install the latest software from Microsoft.
● Obtain updates, as they are released, from the Microsoft Web site and through the updates link in
Help and Support.
136 Chapter 10 Security
Using HP ProtectTools Security Manager (select models only)
HP ProtectTools Security Manager software is preinstalled on select computer models. This software can be accessed through Windows Control Panel. It provides security features that help protect against unauthorized access to the computer, networks, and critical data. For more information, refer to the HP
ProtectTools software Help.
Using HP ProtectTools Security Manager (select models only) 137
Installing a security cable
NOTE:
A security cable is designed to act as a deterrent, but it may not prevent the computer from being mishandled or stolen.
1.
Loop the security cable around a secured object.
2.
Insert the key (1) into the cable lock (2).
3.
Insert the cable lock into the security cable slot on the computer (3), and then lock the cable lock with the key.
NOTE:
Your computer may look different from the illustration. The location of the security cable slot varies by computer model.
138 Chapter 10 Security
11 Software updates
Updating software
Updated versions of the software provided with your computer are available either through the HP
Support Assistant or on the HP Web site.
The HP Support Assistant automatically checks for updates from HP. The utility runs at a specified interval and provides a list of support alerts, such as security enhancements, and optional software and driver updates.
You can manually check for updates at any time by selecting Start > Help and Support > Maintain and following the on-screen instructions.
Most software on the HP Web site is packaged in compressed files called SoftPaqs. Some BIOS updates may be packaged in compressed files called ROMPaqs.
Some download packages contain a file named Readme.txt, which contains information regarding installing and troubleshooting the file. (Readme.txt files included with ROMPaqs are provided in English only.)
You can also access software updates by obtaining the Support Software disc (purchased separately).
This disc includes device drivers, BIOS updates, and utilities.
To purchase the current Support Software disc or a subscription that provides both the current version and future versions of the disc, follow these steps:
1.
Open your Internet browser, and go to http://www.hp.com/support .
2.
Select your country or region.
3.
Click the option for software and driver downloads, and then type your computer model number in the product box.
4.
Press enter .
5.
Follow the on-screen instructions.
To update the software using a Support Software disc, follow these steps:
1.
Insert the Support Software disc into the optical drive.
2.
Follow the on-screen instructions.
Updating software 139
To update the software using the HP Web site, follow these steps:
1.
Identify your computer model, product category, and series or family. Prepare for a system BIOS update by identifying the BIOS version currently installed on the computer. For details, refer to the
"Determining the BIOS version" section.
If your computer is connected to a network, consult the network administrator before installing any software updates, especially system BIOS updates.
NOTE:
The computer system BIOS is stored on the system ROM. The BIOS initializes the operating system, determines how the computer will interact with the hardware devices, and provides for data transfer among hardware devices, including the time and date.
NOTE:
Windows® includes the User Account Control feature to improve the security of your computer. You may be prompted for your permission or password for tasks such as installing software, running utilities, or changing Windows settings. Refer to Help and Support for more information.
2.
Open your Internet browser, and go to http://www.hp.com/support .
3.
Select your country or region.
4.
Click the option for software and driver downloads, and then type your computer model number in the product box.
5.
Press enter .
6.
Follow the on-screen instructions.
140 Chapter 11 Software updates
Updating the BIOS
To update the BIOS, first determine what BIOS version you currently have, and then download and install the new BIOS.
Determining the BIOS version
BIOS version information (also known as ROM date and System BIOS) can be displayed by pressing fn+esc (if you are already in Windows) or by using Computer Setup.
To use Computer Setup for displaying BIOS information, follow these steps:
1.
Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen.
2.
Press f10 to enter BIOS Setup.
3.
Use a pointing device or the arrow keys to select File > System Information.
4.
Press esc to return to the File menu.
5.
Click Exit in the lower-left corner of the screen, and follow the on-screen instructions.
– or –
Use the arrow keys to select File > Ignore changes and exit, and then press enter .
Downloading a BIOS update
CAUTION:
To prevent damage to the computer or an unsuccessful installation, download and install a BIOS update only when the computer is connected to reliable external power using the AC adapter.
Do not download or install a BIOS update while the computer is running on battery power, docked in an optional docking device, or connected to an optional power source. During the download and installation, follow these instructions:
Do not disconnect power from the computer by unplugging the power cord from the AC outlet.
Do not shut down the computer or initiate Sleep or Hibernation.
Do not insert, remove, connect, or disconnect any device, cable, or cord.
To download a BIOS update:
NOTE:
BIOS updates are posted as needed. A newer BIOS update may not be available for your computer. It is recommended that you check the HP Web site periodically for BIOS updates.
1.
Open your Internet browser, go to http://www.hp.com/support , and then select your country or region.
2.
Click the option for software and driver downloads, type your computer model number in the product box, and then press enter .
3.
Click your specific product from the models listed.
4.
Click your operating system.
Updating the BIOS 141
5.
Follow the on-screen instructions to access the BIOS update you want to download. Make a note of the download date, name, or other identifier. You may need this information to locate the update later, after it has been downloaded to your hard drive.
6.
At the download area, perform these steps:
a.
Identify the BIOS update that is newer than the BIOS version currently installed on your computer.
b.
Follow the on-screen instructions to download your selection to the hard drive.
Make a note of the path to the location on your hard drive where the BIOS update will be downloaded. You will need to access this path when you are ready to install the update.
NOTE:
If you connect your computer to a network, consult the network administrator before installing any software updates, especially system BIOS updates.
BIOS installation procedures vary. Follow any on-screen instructions after the download is complete. If no instructions are displayed, follow these steps:
1.
Open Windows Explorer by selecting Start > Computer.
2.
Double-click your hard drive designation. The hard drive designation is typically Local Disk (C:).
3.
Using the hard drive path you recorded earlier, open the folder on your hard drive that contains the update.
4.
Double-click the file that has an .exe extension (for example, filename.exe).
The BIOS installation begins.
NOTE:
Windows® includes the User Account Control feature to improve the security of your computer. You may be prompted for your permission or password for tasks such as installing software, running utilities, or changing Windows settings. Refer to Help and Support for more information.
5.
Complete the installation by following the on-screen instructions.
NOTE:
After an on-screen message reports a successful installation, you may delete the downloaded file from your hard drive.
142 Chapter 11 Software updates
Updating programs and drivers
1.
Open your Internet browser, go to http://www.hp.com/support , and then select your country or region.
2.
Click the option for software and driver downloads, type your computer model number in the product box, and then press enter .
– or –
If you want a specific SoftPaq, type the SoftPaq number in the Search box, at the top-right corner of the screen. Then press enter , and follow the instructions provided. Proceed to step 6.
3.
Click your specific product from the models listed.
4.
Click your operating system.
5.
When the list of updates is displayed, click an update to open a window containing additional information.
6.
Click Download.
7.
Click Run to install the updated software without downloading the file.
– or –
Click Save to save the file to your computer. When prompted, select a storage location on your hard drive.
After the file is downloaded, navigate to the folder where the file was stored, and double-click the file to install the update.
8.
If prompted to do so, restart your computer after the installation is complete.
Updating programs and drivers 143
12 Backup and recovery
To protect your information, use the Backup and Restore Center to back up individual files and folders, back up your entire hard drive (select models only), or create system restore points. In case of system failure, you can use the backup files to restore the contents of your computer.
The Backup and Restore Center provides the following options:
●
Backing up individual files and folders
●
Backing up the entire hard drive (select models only)
●
Scheduling automatic backups (select models only)
●
Creating system restore points
● Recovering individual files
●
Restoring the computer to a previous state
●
Recovering information using recovery tools
NOTE:
For detailed instructions, perform a search for these topics in Help and Support.
NOTE:
In case of system instability, HP recommends that you print the recovery procedures and save them for later use.
144 Chapter 12 Backup and recovery
Backing up your information
Recovery after a system failure is as complete as your most current backup. You should create your initial backup immediately after software setup. As you add new software and data files, you should continue to back up your system on a regular basis to maintain a reasonably current backup.
You can back up your information to an optional external hard drive, a network drive, or discs.
Note the following when backing up:
●
Store personal files in the Documents folder, and back it up regularly.
●
Back up templates that are stored in their associated programs.
●
Save customized settings that appear in a window, toolbar, or menu bar by taking a screen shot of your settings. The screen shot can be a time-saver if you have to reset your preferences.
To create a screen shot:
1.
Display the screen you want to save.
2.
Copy the screen image:
To copy only the active window, press alt+fn+prt sc .
To copy the entire screen, press fn+prt sc .
3.
Open a word-processing document, and then select Edit > Paste.
The screen image is added to the document.
4.
Save the document.
●
When backing up to discs, use any of the following types of discs (purchased separately): CD-R,
CD-RW, DVD+R, DVD+R DL, DVD-R, DVD-R DL, or DVD±RW. The discs you use will depend on the type of optical drive installed in your computer.
NOTE:
DVDs and DVDs with double-layer (DL) support store more information than CDs, so using them for backup reduces the number of recovery discs required.
●
When backing up to discs, number each disc before inserting it into the optical drive of the computer.
To create a backup using Backup and Restore Center, follow these steps:
NOTE:
Be sure that the computer is connected to AC power before you start the backup process.
NOTE:
The backup process may take over an hour, depending on file size and the speed of the computer.
1.
Select Start > All Programs > Maintenance > Backup and Restore Center.
2.
Follow the on-screen instructions to back up your entire computer (select models only) or your files.
NOTE:
Windows® includes the User Account Control feature to improve the security of your computer. You may be prompted for your permission or password for tasks such as installing software, running utilities, or changing Windows settings. Refer to Help and Support for more information.
Backing up your information 145
Performing a recovery
In case of system failure or instability, the computer provides the following tools to recover your files:
●
Windows recovery tools: You can use the Backup and Restore Center to recover information you have previously backed up. You can also use Windows Startup Repair to fix problems that might prevent Windows from starting correctly.
● f11 recovery tools: You can use the f11 recovery tools to recover your original hard drive image.
The image includes the Windows operating system and software programs installed at the factory.
NOTE:
If you are unable to boot (start up) your computer, you must purchase a Windows Vista® operating system DVD to reboot the computer and repair the operating system. For additional information, refer to the “Using a Windows Vista operating system DVD (purchased separately)” section in this guide.
Using the Windows recovery tools
To recover information you previously backed up, follow these steps:
1.
Click Start > All Programs > Maintenance > Backup and Restore Center.
2.
Follow the on-screen instructions to recover your entire computer (select models only) or your files.
NOTE:
Windows includes the User Account Control feature to improve the security of your computer.
You may be prompted for your permission or password for tasks such as installing software, running utilities, or changing Windows settings. Refer to Help and Support for more information.
To recover your information using Startup Repair, follow these steps:
CAUTION:
Using Startup Repair completely erases hard drive contents and reformats the hard drive.
All files you have created and any software installed on the computer are permanently removed. When reformatting is complete, the recovery process restores the operating system, as well as the drivers, software, and utilities from the backup used for recovery.
1.
If possible, back up all personal files.
2.
If possible, check for the presence of the Windows partition and the HP Recovery partition. To find the partitions, select Start > Computer.
NOTE:
If the Windows partition and the HP Recovery partition have been deleted, you must recover your operating system and programs using the Windows Vista operating system DVD and the Driver Recovery disc (both purchased separately). For additional information, refer to the “Using a Windows Vista operating system DVD (purchased separately)” section in this guide.
3.
Restart the computer, and then press f8 before the Windows operating system loads.
4.
Select Repair your computer.
5.
Follow the on-screen instructions.
NOTE:
For additional information on recovering information using the Windows tools, perform a search for these topics in Help and Support.
146 Chapter 12 Backup and recovery
Using f11 recovery tools
CAUTION:
Using f11 completely erases hard drive contents and reformats the hard drive. All files you have created and any software installed on the computer are permanently removed. The f11 recovery tool reinstalls the operating system and HP programs and drivers that were installed at the factory.
Software not installed at the factory must be reinstalled. Personal files must be restored from a backup.
NOTE:
If your computer includes a solid-state drive (SSD), you may not have a recovery partition.
Recovery discs have been included for computers that do not have a partition. Use these discs to recover your operating system and software. To check for the presence of a recovery partition, select Start >
Computer. If the partition is present, an HP Recovery drive is listed in the Hard Disk Drives section of the window.
To recover the original hard drive image using f11 , follow these steps:
1.
If possible, back up all personal files.
2.
If possible, check for the presence of the HP Recovery partition. To find the partition, select
Start > Computer.
NOTE:
If the HP Recovery partition has been deleted, you must recover your operating system and programs using the Windows Vista operating system DVD and the Driver Recovery disc (both purchased separately). For additional information, refer to the “Using a Windows Vista operating system DVD (purchased separately)” section in this guide.
3.
Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen.
4.
Press f11 while the “Press <F11> for recovery” message is displayed on the screen.
5.
Follow the on-screen instructions.
Using a Windows Vista operating system DVD (purchased separately)
If you are unable to boot (start up) your computer, you must purchase a Windows Vista operating system
DVD to reboot the computer and repair the operating system. Make sure that your most recent backup
(stored on discs or on an external drive) is easily accessible. To order a Windows Vista operating system
DVD, go to http://www.hp.com/support , select your country or region, and follow the on-screen instructions. You can also order the DVD by calling technical support. For contact information, refer to the Worldwide Telephone Numbers booklet included with the computer.
CAUTION:
Using a Windows Vista operating system DVD completely erases hard drive contents and reformats the hard drive. All files you have created and any software installed on the computer are permanently removed. When reformatting is complete, the recovery process helps you restore the operating system, as well as drivers, software, and utilities.
To initiate recovery using a Windows Vista operating system DVD, follow these steps:
NOTE:
This process takes several minutes.
1.
If possible, back up all personal files.
2.
Restart the computer, and then insert the Windows Vista operating system DVD into the optical drive before the Windows operating system loads.
3.
When prompted, press any keyboard key.
4.
Follow the on-screen instructions.
Performing a recovery 147
5.
Click Next.
6.
Select Repair your computer.
7.
Follow the on-screen instructions.
148 Chapter 12 Backup and recovery
13 Computer Setup
Starting Computer Setup
Computer Setup is a preinstalled, ROM-based utility that can be used even when the operating system is not working or will not load.
NOTE:
Some of the Computer Setup menu items listed in this guide may not be supported by your computer.
NOTE:
An external keyboard or mouse connected to a USB port can be used with Computer Setup only if USB legacy support is enabled.
To start Computer Setup, follow these steps:
1.
Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen.
2.
Press f10 to enter BIOS Setup.
Using Computer Setup
Navigating and selecting in Computer Setup
The information and settings in Computer Setup are accessed from the File, Security, Diagnostics, and
System Configuration menus.
To navigate and select in Computer Setup, follow these steps:
1.
Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen.
●
To select a menu or a menu item, use the tab key and the keyboard arrow keys and then press enter , or use a pointing device to click the item.
● To scroll up and down, click the up arrow or the down arrow in the upper-right corner of the screen, or use the up arrow key or the down arrow key.
●
To close open dialog boxes and return to the main Computer Setup screen, press esc , and then follow the on-screen instructions.
NOTE:
You can use either a pointing device (TouchPad, pointing stick, or USB mouse) or the keyboard to navigate and make selections in Computer Setup.
2.
Press f10 to enter BIOS Setup.
3.
Select the File, Security, Diagnostics, or System Configuration menu.
Starting Computer Setup 149
To exit Computer Setup menus, choose one of the following methods:
● To exit Computer Setup menus without saving your changes, click the Exit icon in the lower-left corner of the screen, and then follow the on-screen instructions.
– or –
Use the tab key and the arrow keys to select File > Ignore changes and exit, and then press enter .
– or –
● To save your changes and exit Computer Setup menus, click the Save icon in the lower-left corner of the screen, and then follow the on-screen instructions.
– or –
Use the tab key and the arrow keys to select File > Save changes and exit, and then press enter .
Your changes go into effect when the computer restarts.
Restoring factory settings in Computer Setup
NOTE:
Restoring defaults will not change the hard drive mode.
To return all settings in Computer Setup to the values that were set at the factory, follow these steps:
1.
Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen.
2.
Press f10 to enter BIOS Setup.
3.
Use a pointing device or the arrow keys to select File > Restore defaults.
4.
Follow the on-screen instructions.
5.
To save your changes and exit, click the Save icon in the lower-left corner of the screen, and then follow the on-screen instructions.
– or –
Use the arrow keys to select File > Save changes and exit, and then press enter .
Your changes go into effect when the computer restarts.
NOTE:
Your password settings and security settings are not changed when you restore the factory settings.
Computer Setup menus
The menu tables in this section provide an overview of Computer Setup options.
NOTE:
Some of the Computer Setup menu items listed in this chapter may not be supported by your computer.
150 Chapter 13 Computer Setup
File menu
Select
System Information
Set System Date and Time
System Diagnostics
Reset BIOS security to factory default
Restore defaults
Ignore changes and exit
Save changes and exit
To do this
●
View identification information for the computer and the batteries in the system.
●
View specification information for the processor, cache and memory size, system ROM, video revision, and keyboard controller version.
Set or change the date and time on the computer.
Displays the following information:
● System Information
◦
Identification information for the computer and the batteries in the system.
◦ Specification information for the processor, cache and memory size, system ROM, video revision, and keyboard controller version.
●
Start-up Test—Verifies the system components needed for starting the computer.
● Run-In Test—Runs a comprehensive check on system memory.
●
Hard Disk Test—Runs a comprehensive self-test on any hard drive in the system.
● Memory Test—Runs a comprehensive test on any memory installed in the computer.
●
Battery Test—Runs a comprehensive test on any batteries installed in the computer.
●
Error Log—Displays a log file if any errors have occurred.
Restore the BIOS security settings to the factory default.
Replace the configuration settings in Computer Setup with the original factory settings. (Hard drive mode, password settings, and security settings are not changed when you restore the factory settings.)
Cancel any changes entered during the current session. Then exit and restart the computer.
Save any changes entered during the current session. Then exit and restart the computer. Your changes go into effect when the computer restarts.
Security menu
NOTE:
Some of the menu items listed in this section may not be supported by your computer.
Select
Setup BIOS Administrator Password
To do this
Set up a BIOS administrator password.
Computer Setup menus 151
Select
Password Policy (requires a BIOS administrator password)
HP SpareKey
Always Prompt for HP SpareKey Enrollment
Fingerprint Reset on Reboot (If Present)
Change Password
HP SpareKey Enrollment
DriveLock Passwords
Automatic DriveLock
TPM Embedded Security
Disk Sanitizer
System IDs
To do this
Revise password policy criteria.
Enable/disable HP SpareKey (enabled by default).
Enable/disable HP SpareKey enrollment (enabled by default).
Reset/clear the fingerprint reader ownership (select models only; disabled by default).
Enter, change, or delete a BIOS administrator password.
Enroll or reset HP SpareKey, which is a set of security questions and answers used if you forget your password.
●
Enable/disable DriveLock on any computer hard drive
(enabled by default).
● Change a DriveLock user password or master password.
NOTE:
DriveLock settings are accessible only when you enter Computer Setup by turning on (not restarting) the computer.
Enable/disable Automatic DriveLock support.
Enable/disable support for Trusted Platform Module (TPM)
Embedded Security, which protects the computer from unauthorized access to owner functions available in
Embedded Security for ProtectTools. For more information, refer to the ProtectTools software Help.
NOTE:
You must have a setup password to change this setting.
Run Disk Sanitizer to destroy all existing data on the primary hard drive or the drive in the upgrade bay.
CAUTION:
If you run Disk Sanitizer, the data on the selected drive is destroyed permanently.
Enter a user-defined computer asset tracking number and ownership tag.
System Configuration menu
NOTE:
Some of the listed System Configuration options may not be supported by your computer.
Select
Language
Boot Options
To do this
Change the Computer Setup language.
●
Set a Startup Menu delay (in seconds).
● Enable/disable MultiBoot (enabled by default).
●
Set the Express Boot Popup delay in seconds.
● Enable/disable Custom Logo (disabled by default).
●
Enable/disable Display Diagnostic URL (enabled by default).
152 Chapter 13 Computer Setup
Select
Device Configurations
To do this
●
Enable/disable CD-ROM boot (disabled by default).
●
Enable/disable SD Card boot (enabled by default).
● Enable/disable floppy boot (enabled by default).
●
Enable/disable PXE Internal NIC boot (enabled by default).
●
Enable/Disable Unified Extensible Firmware Interface
(UEFI) Boot Mode (disabled by default).
●
Set the Legacy Boot Order.
● Enable/disable USB legacy support (enabled by default).
When enabled, USB legacy support allows the following:
◦
◦
Use of a USB keyboard in Computer Setup even when a Windows® operating system is not running
Startup from bootable USB devices, including a hard drive, diskette drive, or optical drive connected by a
USB port to the computer
●
Select a parallel port mode: ECP (Enhanced Capabilities
Port), standard, bidirectional, or EPP (Enhanced Parallel
Port).
● Enable/disable fan always on while connected to an AC outlet (disabled by default).
●
Enable/disable Data Execution Prevention (select models only). When enabled, the processor can disable some virus code execution, which helps to improve computer security (disabled by default).
● SATA (Serial Advanced Technology Attachment) device mode. The following options are available:
◦
◦
◦
AHCI (Advanced Host Controller Interface)
IDE (Integrated Drive Electronics)
RAID (select models only)
NOTE:
Availability of these options varies by computer model.
●
Enable/disable secondary battery fast charge (enabled by default).
● Enable/disable HP QuickLook (enabled by default).
●
Enable/disable Preboot Authentication on HP QuickLook
Boot (enabled by default).
● Enable/disable HP QuickWeb (enabled by default).
●
Enable/disable HP QuickWeb Elevated Security
(disabled by default).
● Enable/disable Virtualization Technology (select models only; disabled by default).
Computer Setup menus 153
Select
Built-In Device Options
Port Options (all are enabled by default)
To do this
●
Enable/disable Wake on USB (enabled by default).
●
Enable/disable Num lock state at boot (disabled by default).
●
Enable/disable TXT (Intel® Trusted Execution
Technology) (select models only; disabled by default).
●
Enable/disable the wireless button state (enabled by default).
● Enable/disable embedded WLAN device radio (select models only; enabled by default).
●
Enable/disable the Network Interface Controller (LAN)
(enabled by default).
● Enable/disable the embedded Bluetooth® device radio
(enabled by default).
●
Enable/disable LAN/WLAN switching (disabled by default).
● Enable/disable LAN Power Save (select models only).
When enabled, saves power by turning off the LAN when not in use (enabled by default).
●
Set the wake on LAN state. Options include the following:
◦
◦ Disabled
Boot to Network
◦ Follow Boot Order
●
Enable/disable the Notebook Upgrade Bay device
(enabled by default).
● Enable/disable the Power Monitor Circuit (enabled by default).
●
Enable/disable the audio devices (enabled by default).
● Enable/disable the fingerprint device (enabled by default).
●
Enable/disable a modem device (enabled by default).
● Enable/disable the microphone (enabled by default).
●
Enable/disable the internal speakers (enabled by default).
NOTE:
All port options are enabled by default.
● Enable/disable the serial port.
●
Enable/disable the parallel port.
●
Enable/disable the flash media reader.
●
Enable/disable the USB port.
154 Chapter 13 Computer Setup
Select
Set Security Level
Restore Security Defaults
To do this
CAUTION:
Disabling the USB port also disables
MultiBay devices and ExpressCard devices on the advanced port replicator.
●
Enable/disable the 1394 port.
● Enable/disable the ExpressCard slot.
●
Enable/disable the Smart Card slot.
●
Enable/disable the eSATA port.
Change, view, or hide security levels for all BIOS menu items.
Restore the default security settings.
Computer Setup menus 155
14 MultiBoot
About the boot device order
As the computer starts, the system attempts to boot from enabled boot devices. The MultiBoot utility, which is enabled at the factory, controls the order in which the system selects a boot device. Boot devices can include optical drives, diskette drives, a network interface card (NIC), hard drives, and USB devices.
Boot devices contain bootable media or files that the computer needs to start and operate properly.
NOTE:
Some boot devices must be enabled in Computer Setup before they can be included in the boot order.
The factory setting is for the computer to select the boot device by searching enabled boot devices and drive bay locations in the following order:
NOTE:
Some of the boot devices and drive bay locations listed may not be supported on your computer.
●
Notebook upgrade bay
●
Internal hard drive
●
USB diskette drive
●
USB CD-ROM
●
USB hard drive
●
Notebook Ethernet
●
Secure Digital (SD) Memory Card
●
Docking device upgrade bay
●
External SATA drive
You can change the order in which the computer searches for a boot device by changing the boot order in Computer Setup. You can also press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen, and then press f9 . Pressing f9 displays a menu that shows the current boot devices and allows you to select a boot device. Or, you can use MultiBoot Express to set the computer to prompt you for a boot location each time the computer turns on or restarts.
If MultiBoot is disabled, the computer uses a fixed boot order that consists of first searching for a drive
A boot device. If none is found, the computer looks for a drive C boot device. Drive A boot devices include optical drives and diskette drives. Drive C boot devices include optical drives and hard drives.
The NIC does not have an assigned drive letter.
156 Chapter 14 MultiBoot
NOTE:
An optical drive (such as a CD-ROM drive) can boot either as drive A or drive C, depending on the format of the boot CD.
About the boot device order 157
Enabling boot devices in Computer Setup
The computer will boot to a USB device or a NIC device only if the device has first been enabled in
Computer Setup.
To start Computer Setup and enable a USB device or a NIC device as a boot device, follow these steps:
1.
Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen.
2.
Press f10 to enter BIOS Setup.
3.
To enable bootable media in USB drives or in drives inserted into an optional docking device (select models only), use a pointing device or the arrow keys to select System Configuration > Device
Configurations. Confirm that Enabled is selected next to USB legacy support.
NOTE:
The USB Port option must be enabled in order to use USB legacy support. It is enabled at the factory. If the port becomes disabled, reenable it by selecting System Configuration > Port
Options, and then clicking Enabled next to USB Port.
– or –
To enable a NIC device, select System Configuration > Boot Options, and then click Enabled next to PXE Internal NIC boot.
4.
To save your changes and exit Computer Setup, click Save in the lower-left corner of the screen, and then follow the on-screen instructions.
– or –
Use the arrow keys to select File > Save changes and exit, and then press enter .
Your changes go into effect when the computer restarts.
NOTE:
To connect a NIC to a Preboot eXecution Environment (PXE) or Remote Program Load (RPL) server without using MultiBoot, press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen, and then quickly press f12 .
158 Chapter 14 MultiBoot
Considering boot order changes
Before changing the boot order, note the following considerations:
●
When the computer restarts after the boot order has been changed, the computer attempts to start using the new boot order.
●
If there is more than one type of boot device, the computer attempts to boot using the first of each type of boot device (except for optical devices). For example, if the computer is connected to an optional docking device (select models only) that contains a hard drive, this hard drive will be shown in the boot order as a USB hard drive. If the system attempts to boot from this USB hard drive and fails, it will not attempt to boot to the hard drive in the hard drive bay. Instead, it will try to boot to the next type of device in the boot order. However, if there are 2 optical devices, and the first optical device does not boot (either because it does not contain media or the media is not a boot disc), the system will try to boot to the second optical device.
●
Changing the boot order also changes the logical drive designations. For example, if you start up from a CD-ROM drive with a disc formatted as drive C, that CD-ROM drive becomes drive C and the hard drive in the hard drive bay becomes drive D.
●
The computer will boot from a NIC device only if the device has been enabled in the Built-In Device
Options menu of Computer Setup and if booting from the device has been enabled in the Boot
Options menu of Computer Setup. Booting from a NIC does not affect logical drive designations because no drive letter is associated with the NIC.
●
Drives in an optional docking device (select models only) are treated like external USB devices in the boot order.
Considering boot order changes 159
Choosing MultiBoot preferences
You can use MultiBoot in the following ways:
●
To set a new boot order that the computer uses each time it is turned on, by changing the boot order in Computer Setup.
●
To dynamically choose the boot device, by pressing esc while the “Press the ESC key for Startup
Menu” message is displayed at the bottom of the screen, and then pressing f9 to enter the Boot
Device Options menu.
●
To use MultiBoot Express to set variable boot orders. This feature prompts you for a boot device each time the computer is turned on or restarted.
Setting a new boot order in Computer Setup
To start Computer Setup and set a boot device order that the computer uses each time it is turned on or restarted, follow these steps:
1.
Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen.
2.
Press f10 to enter BIOS Setup.
3.
Use a pointing device or the arrow keys to select System Configuration > Boot Options. Confirm that Enabled is selected next to MultiBoot.
NOTE:
MultiBoot is enabled at the factory.
4.
Use a pointing device or the arrow keys to select a device in the list.
5.
To move the device up in the boot order, use a pointing device to click the up arrow key next to the device name, or press the + key.
– or –
To move the device down in the boot order, use a pointing device to click the down arrow key next to the device name, or press the key.
6.
To save your changes and exit Computer Setup, click Save in the lower-left corner of the screen, and then follow the on-screen instructions.
– or –
Use the arrow keys to select File > Save changes and exit, and then press enter .
Your changes go into effect when the computer restarts.
160 Chapter 14 MultiBoot
Dynamically choosing a boot device using the F9 prompt
To dynamically choose a boot device for the current startup sequence, follow these steps:
1.
Open the Select Boot Device menu by turning on or restarting the computer, and then pressing esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen.
2.
Press f9 .
3.
Use a pointing device or the arrow keys to select a boot device, and then press enter .
Your changes go into effect immediately.
Setting a MultiBoot Express prompt
To start Computer Setup and set the computer to display the MultiBoot startup location menu each time the computer is started or restarted, follow these steps:
1.
Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen.
2.
Press f10 to enter BIOS Setup.
3.
Use a pointing device or the arrow keys to select System Configuration > Boot Options, and then press enter .
4.
In the Express Boot Popup Delay (Sec) field, enter the length of time in seconds that you want the computer to display the startup location menu before it defaults to the current MultiBoot setting.
(When 0 is selected, the Express Boot startup location menu is not displayed.)
5.
To save your changes and exit Computer Setup, click Save in the lower-left corner of the screen, and then follow the on-screen instructions.
– or –
Use the arrow keys to select File > Save changes and exit, and then press enter .
Your changes go into effect when the computer restarts.
Entering MultiBoot Express preferences
When the Express Boot menu displays during startup, you have the following choices:
●
To specify a boot device from the Express Boot menu, select your preference within the allotted time, and then press enter .
●
To prevent the computer from defaulting to the current MultiBoot setting, press any key before the allotted time expires. The computer will not start until you select a boot device and press enter .
●
To allow the computer to start according to the current MultiBoot settings, wait for the allotted time to expire.
Choosing MultiBoot preferences 161
15 Management and printing
Using Client Management Solutions
Client Management Solutions software provides standards-based solutions for managing client (user) desktop, workstation, notebook, and tablet computers in a networked environment.
Client management includes the following key capabilities and features:
●
Initial software image deployment
●
Remote system software installation
●
Software management and updates
●
ROM updates
●
Tracking and security of computer assets (the hardware and software installed on the computer)
● Fault notification and recovery of certain system software and hardware components
NOTE:
Support for specific features described in this section may vary, depending on computer model and/or version of management software installed on the computer.
Configuring and deploying a software image
The computer is shipped with a preinstalled system software image. The initial software image is configured during the first-time setup of the computer. After a brief software "unbundling" occurs, the computer is ready to be used.
A customized software image can be deployed (distributed) in one of the following ways:
●
Installing additional software applications after unbundling the preinstalled software image
● Using software deployment tools, such as Altiris Deployment Solutions, to replace the preinstalled software with a customized software image
●
Using a disk-cloning process to copy the contents from one hard drive to another
The deployment method you use depends on your organization's technology environment and processes.
NOTE:
The Computer Setup utility and other system features provide further assistance with configuration management and troubleshooting, power management, and the recovery of system software.
162 Chapter 15 Management and printing
Managing and updating software
HP provides several tools for managing and updating software on client computers:
●
HP Client Manager for Altiris (select models only)
NOTE:
To download HP Client Manager for Altiris or to obtain more information about HP Client
Manager for Altiris, see the HP Web site at http://www.hp.com
.
● HP CCM (Client Configuration Manager) (select models only)
●
HP SSM (System Software Manager)
HP Client Manager for Altiris (select models only)
HP Client Manager for Altiris integrates Intelligent Manageability technology into Altiris software. HP
Client Manager for Altiris provides superior hardware management capabilities for HP devices:
●
Detailed views of hardware inventory for asset management
● System Checkup monitoring and diagnostics
●
Web-accessible reporting of business-critical details such as thermal warnings and memory alerts
● Remote updating of system software such as device drivers and the system BIOS
NOTE:
Additional functionality can be added when HP Client Manager for Altiris is used with optional
Altiris Solutions software (purchased separately).
When HP Client Manager for Altiris (installed on a client computer) is used with Altiris Solutions software
(installed on an administrator computer), HP Client Manager for Altiris provides increased management functionality and centralized hardware management of client devices for the following IT life-cycle areas:
●
Inventory and asset management
◦
Software license compliance
◦
Computer tracking and reporting
◦
Computer lease contract information and fixed asset tracking
●
System software deployment and migration
◦
Windows® migration
◦
System deployment
◦
Personality (personal user settings) migration
Using Client Management Solutions 163
●
Help desk and problem resolution
◦ Management of help desk tickets
◦
Remote troubleshooting
◦
Remote problem resolution
◦
Client disaster recovery
●
Software and operations management
◦
Ongoing client management
◦ HP system software deployment
◦
Application self-healing (the ability to identify and repair certain application problems)
Altiris Solutions software provides easy-to-use software distribution capabilities. HP Client Manager for
Altiris enables communication with the Altiris Solutions software, which can be used to complete new hardware deployment or personality migration to a new operating system using easy-to-follow wizards.
HP Client Manager for Altiris is available for download from the HP Web site.
When Altiris Solutions software is used in conjunction with HP System Software Manager or HP Client
Manager for Altiris, administrators can also update the system BIOS and device driver software from a central console.
164 Chapter 15 Management and printing
HP CCM (Client Configuration Manager) (select models only)
HP CCM (Client Configuration Manager) automates the management of software such as operating systems, programs, software updates, and content and configuration settings to ensure that each computer is maintained in the correct configuration. With these automated management solutions, you can manage software throughout the life cycle of the computer.
CCM enables you to perform the following tasks:
●
Collect hardware and software inventory across multiple platforms
●
Prepare a software package and conduct impact analysis prior to distribution
●
Target individual computers, workgroups, or entire populations of computers for deployment and maintenance of software and content according to policies
●
Provision and manage operating systems, applications, and content on distributed computers from any location
●
Integrate CCM with help desks and other system management tools for seamless operations
●
Leverage a common infrastructure for management of software and content on standard computing devices across any network for all enterprise users
●
Scale to meet enterprise needs
Using Client Management Solutions 165
HP SSM (System Software Manager)
HP SSM (System Software Manager) lets you remotely update system-level software on multiple systems simultaneously. When executed on a client computer, SSM detects versions of both hardware and software, and then updates designated software from a central repository, known as a file store.
Driver versions that are supported by SSM are denoted with a special icon on the HP driver download
Web site and on the Support Software CD. To download the SSM utility or to obtain more information on SSM, see the HP Web site at http://www.hp.com/go/ssm (English only).
166 Chapter 15 Management and printing
Using the HP Universal Print Driver
The HP Universal Print Driver Series for Windows is a single intelligent driver that replaces individual drivers for HP networked printers.
NOTE:
The HP Universal Print Driver is preinstalled on select computer models only. To download the HP Universal Print Driver or obtain more information about using it, see the HP Web site at http://www.hp.com/go/universalprintdriver (English only).
To print using the HP Universal Print Driver:
1.
Select File > Print from any application.
2.
Select HP Universal Printing PS from the list of printers.
3.
Click Print.
4.
Enter the printer's IP address or network path.
NOTE:
If you cannot identify the printer's IP address or network path, contact your IT administrator for help.
5.
Select the Make a permanent instance of this printer in my Printers folder check box.
6.
Click Print.
Using the HP Universal Print Driver 167
Index
Symbols/Numerics
1394 devices
A
AC adapter
Altiris Deployment Solutions 162
applications key, Windows 9, 10
audio devices, connecting
external 53 audio functions, checking 53
audio-out (headphone) jack 13,
Automatic DriveLock password
B
Backup and Restore Center 144,
battery
calibrating 80 charging 78, 80
battery charge, maximizing 79 battery light 11, 78, 79
bays
BD
BIOS administrator
BIOS update
Blu-ray ROM DVD±RW SuperMulti
boot options 152 boot order 152
built-in device
Bluetooth device radio 154 fingerprint reader 154 internal speakers 154
LAN/WLAN switching 154 microphone 154 modem 154
Network Interface Controller
Wake on LAN 154 wireless button 154
WLAN device radio 154 built-in device options 154
business card reader software 69
business card slot, identifying 11
buttons
C
cables
caps lock light, identifying 4, 5
CD
Certificate of Authenticity label 20
components
168 Index
Computer Setup
BIOS administrator
enabling bootable
restoring factory settings 150
setting MultiBoot Express
System Configuration
country-specific modem cable
D
device drivers
Microsoft drivers 66 reinstalling 66
digital card
display
display release latch,
DisplayPort, identifying 13, 14
DriveLock password
drives
DVD±RW SuperMulti DL
DVD
E
embedded numeric keypad keys,
expansion memory module
ExpressCard
external audio devices,
external monitor port,
F
fingerprint reader, identifying 5,
function keys, identifying 9, 10
H
hard drive
Hibernation
initiated during critical battery
hotkeys decreasing screen
displaying system
increasing screen
HP Client Configuration
HP Client Manager for
HP Connection Manager
Index 169
HP System Software
I
icons
inserting a memory module
integrated numeric keypad keys,
integrated numeric keypad,
internal microphones,
J
jacks
Java Card
defined 113 inserting 113 removing 113
K
keyboard hotkeys, identifying 40
keyboard screws
keypad, embedded
keypad, external
keypad, integrated
keys
L
labels
HP Mobile Broadband
Microsoft Certificate of
SIM 20 wireless certification 20
language, changing in Computer
lights
logical drive designations 159
M
maintenance
memory module compartment cover
Microsoft Certificate of Authenticity
modem cable
country-specific cable
noise suppression circuitry 35
modem software
mouse, external
connecting 40 setting preferences 40
multimedia software, installing 52
N
network security codes
noise suppression circuitry
num lk key, identifying 47, 48 num lock, external keypad 48
O
operating system
Microsoft Certificate of
optical disc
P
passwords
170 Index
pointing devices
setting preferences 40 using 40
pointing stick
port options
flash media reader 154 parallel port 154 serial port 154
ports
power
power button, identifying 6, 7
power connector, identifying 14,
power light, identifying 3, 4, 11
primary memory module
product name and number,
Q
QuickLook button, identifying 6,
QuickLook light, identifying 4, 5
QuickWeb button, identifying 6,
QuickWeb light, identifying 4, 5
R
regulatory information
regulatory label 20 wireless certification labels 20
replacing a primary memory
replacing an expansion memory
restore the factory settings 151
RJ-45 (network) jack,
S
SATA (Serial Advanced
Technology Attachment) devices
AHCI (Advanced Host Controller
IDE (Integrated Drive
Secondary Battery Fast
security cable slot, identifying 12,
Security menu always prompt for HP SpareKey
Automatic DriveLock 152 change password 152
DriveLock 152 fingerprint reader reset 152
HP Sparekey enrollment 152 password policy 152
set up BIOS administrator
serial number, computer 19 service tag 19
setup utility
restoring factory settings 150
System Configuration
Sleep
slots
smart card
defined 113 inserting 113 removing 113
smart card reader, identifying 14
software
system date and time 151 system diagnostics 151
T
TouchPad
Index 171
traveling with the computer 20,
troubleshooting
optical disc tray 63 optical drive detection 63
troubleshooting, wireless network
TXT (Intel® Trusted Execution
U
Unified Extensible Firmware
upgrade bay
USB devices
connecting 101 description 101
USB ports, identifying 13, 14,
V
volume down button,
volume mute button,
identifying 7, 8 volume up button, identifying 7
W
Web sites
HP System Software
webcam
webcam light, identifying 11, 17
webcam properties, adjusting 68
Windows applications key,
Windows logo key, identifying 9,
Windows Vista operating system
Wireless Assistant software 22,
wireless button, identifying 6, 8
wireless certification label 20
wireless controls
Wireless Assistant
software 22 wireless icon 22 wireless light 22
wireless light, identifying 3, 4,
wireless network (WLAN)
corporate WLAN
functional range 27 public WLAN connection 27
wireless network problems,
172 Index
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 11 Features
- 11 Identifying hardware
- 11 Top components
- 11 TouchPad
- 13 Lights
- 15 Buttons and fingerprint reader
- 19 Keys
- 20 Front components
- 21 Right-side components
- 23 Left-side components
- 24 Rear components
- 25 Bottom components
- 26 Display components
- 27 Wireless antennas (select models only)
- 29 Additional hardware components
- 29 Identifying the labels
- 31 Wireless, modem, and local area network
- 31 Using wireless devices (select models only)
- 32 Identifying wireless and network icons
- 32 Using the wireless controls
- 32 Using the wireless button
- 33 Using Wireless Assistant software (select models only)
- 33 Using HP Connection Manager (select models only)
- 33 Using operating system controls
- 35 Using a WLAN device (select models only)
- 35 Setting up a WLAN
- 35 Protecting your WLAN
- 37 Connecting to a WLAN
- 37 Roaming to another network
- 38 Using HP Mobile Broadband (select models only)
- 38 Inserting a SIM
- 39 Removing a SIM
- 41 Using a Bluetooth wireless device
- 41 Bluetooth and Internet Connection Sharing (ICS)
- 42 Troubleshooting wireless network problems
- 42 Cannot create a WLAN connection
- 43 Cannot connect to a preferred network
- 43 Network status icon is not displayed
- 43 Current network security codes are unavailable
- 44 WLAN connection is very weak
- 44 Cannot connect to the wireless router
- 45 Using the modem (select models only)
- 45 Connecting a modem cable
- 46 Connecting a country- or region-specific modem cable adapter
- 46 Selecting a location setting
- 46 Viewing the current location selection
- 47 Adding new locations when traveling
- 48 Solving travel connection problems
- 49 Connecting to a local area network (LAN)
- 50 Pointing devices and keyboard
- 50 Using pointing devices
- 50 Setting pointing device preferences
- 50 Using the TouchPad
- 50 Using the pointing stick (select models only)
- 50 Connecting an external mouse
- 50 Using the keyboard
- 50 Using hotkeys
- 51 Displaying system information
- 52 Initiating Sleep
- 53 Switching the screen image
- 54 Displaying Power Assistant
- 55 Decreasing screen brightness
- 55 Increasing screen brightness
- 56 Using HP QuickLook 3
- 56 Using keypads
- 56 Using the embedded numeric keypad
- 57 Enabling and disabling the embedded numeric keypad
- 57 Switching key functions on the embedded numeric keypad
- 57 Using the integrated numeric keypad
- 58 Using an optional external numeric keypad
- 59 Cleaning the TouchPad and keyboard
- 60 Multimedia
- 60 Multimedia features
- 60 Adjusting the volume
- 61 Multimedia software
- 62 Accessing your preinstalled multimedia software
- 62 Installing multimedia software from a disc
- 63 Audio
- 63 Connecting external audio devices
- 63 Checking your audio functions
- 65 Video
- 65 Connecting an external monitor or projector
- 65 Using the external monitor port
- 65 Using the DisplayPort
- 67 Optical drive (select models only)
- 67 Identifying the optical drive
- 67 Using optical discs (CDs, DVDs, and BDs)
- 68 Selecting the right disc (CDs, DVDs, and BDs)
- 68 CD-R discs
- 68 CD-RW discs
- 68 DVD±R discs
- 68 DVD±RW discs
- 68 LightScribe DVD+R discs
- 69 Blu-ray Discs (BDs)
- 69 Playing a CD, DVD, or BD
- 70 Configuring AutoPlay
- 70 Changing DVD region settings
- 70 Observing the copyright warning
- 71 Copying a CD, DVD, or BD
- 71 Creating (burning) a CD or DVD
- 72 Removing an optical disc (CD, DVD, or BD)
- 72 Troubleshooting
- 73 The optical disc tray does not open for removal of a CD, DVD, or BD
- 73 The computer does not detect the optical drive
- 74 A disc does not play
- 74 A disc does not play automatically
- 75 A movie stops, skips, or plays erratically
- 75 A movie is not visible on an external display
- 75 The process of burning a disc does not begin, or it stops before completion
- 76 A device driver must be reinstalled
- 76 Obtaining the latest HP device drivers
- 76 Obtaining Microsoft device drivers
- 78 Webcam (select models only)
- 78 Adjusting webcam properties
- 79 Capturing business card images
- 81 Power management
- 81 Setting power options
- 81 Using power-saving states
- 81 Initiating and exiting Sleep
- 82 Initiating and exiting Hibernation
- 82 Using the battery meter
- 82 Using power plans
- 83 Viewing the current power plan
- 83 Selecting a different power plan
- 83 Customizing power plans
- 83 Setting password protection on wakeup
- 84 Using Power Assistant (select models only)
- 84 Starting Power Assistant
- 84 Using external AC power
- 85 Connecting the AC adapter
- 85 Using battery power
- 86 Finding battery information in Help and Support
- 86 Using Battery Check
- 86 Displaying the remaining battery charge
- 87 Inserting or removing the battery
- 88 Charging a battery
- 89 Maximizing battery discharge time
- 89 Managing low battery levels
- 89 Identifying low battery levels
- 90 Resolving a low battery level
- 90 Resolving a low battery level when external power is available
- 90 Resolving a low battery level when a charged battery is available
- 90 Resolving a low battery level when no power source is available
- 90 Resolving a low battery level when the computer cannot exit Hibernation
- 90 Calibrating a battery
- 90 Step 1: Fully charge the battery
- 91 Step 2: Disable Hibernation and Sleep
- 91 Step 3: Discharge the battery
- 93 Step 4: Fully recharge the battery
- 93 Step 5: Reenable Hibernation and Sleep
- 93 Conserving battery power
- 93 Storing a battery
- 94 Disposing of a used battery
- 94 Replacing the battery
- 95 Testing an AC adapter
- 95 Shutting down the computer
- 97 Drives
- 97 Identifying installed drives
- 97 Handling drives
- 99 Improving hard drive performance
- 99 Using Disk Defragmenter
- 99 Using Disk Cleanup
- 100 Using HP 3D DriveGuard
- 100 Identifying HP 3D DriveGuard status
- 101 Using HP 3D DriveGuard software
- 102 Replacing a hard drive in the hard drive bay
- 105 Replacing a drive in the upgrade bay
- 105 Removing the protective insert
- 105 Replacing a hard drive
- 108 Replacing an optical drive
- 111 External devices
- 111 Using a USB device
- 111 Connecting a USB device
- 112 Stopping and removing a USB device
- 112 Using USB legacy support
- 113 Using a 1394 device
- 113 Connecting a 1394 device
- 113 Stopping and removing a 1394 device
- 115 Using a serial device (select models only)
- 116 Using external drives
- 116 Using optional external devices
- 117 Using a docking device
- 118 External media cards
- 118 Using Media Card Reader cards
- 118 Inserting a digital card
- 119 Stopping and removing a digital card
- 120 Using ExpressCards (select models only)
- 120 Configuring an ExpressCard
- 120 Inserting an ExpressCard
- 121 Stopping and removing an ExpressCard
- 123 Using Smart Cards (select models only)
- 123 Inserting a smart card
- 123 Removing a smart card
- 124 Memory modules
- 125 Adding or replacing a memory module in the expansion memory module slot
- 128 Upgrading a memory module in the primary memory module slot
- 132 Security
- 132 Protecting the computer
- 133 Using passwords
- 133 Setting passwords in Windows
- 133 Setting passwords in Computer Setup
- 134 BIOS administrator password
- 135 Managing a BIOS administrator password
- 136 Entering a BIOS administrator password
- 136 Using Computer Setup DriveLock
- 137 Setting a DriveLock password
- 138 Entering a DriveLock password
- 139 Changing a DriveLock password
- 140 Removing DriveLock protection
- 140 Using Computer Setup Auto DriveLock
- 140 Entering an Automatic DriveLock password
- 141 Removing Automatic DriveLock protection
- 142 Using Computer Setup security features
- 142 Securing system devices
- 142 Viewing Computer Setup System Information
- 143 Using Computer Setup System IDs
- 144 Using antivirus software
- 145 Using firewall software
- 146 Installing critical updates
- 147 Using HP ProtectTools Security Manager (select models only)
- 148 Installing a security cable
- 149 Software updates
- 149 Updating software
- 151 Updating the BIOS
- 151 Determining the BIOS version
- 151 Downloading a BIOS update
- 153 Updating programs and drivers
- 154 Backup and recovery
- 155 Backing up your information
- 156 Performing a recovery
- 156 Using the Windows recovery tools
- 157 Using f11 recovery tools
- 157 Using a Windows Vista operating system DVD (purchased separately)
- 159 Computer Setup
- 159 Starting Computer Setup
- 159 Using Computer Setup
- 159 Navigating and selecting in Computer Setup
- 160 Restoring factory settings in Computer Setup
- 160 Computer Setup menus
- 161 File menu
- 161 Security menu
- 162 System Configuration menu
- 166 MultiBoot
- 166 About the boot device order
- 168 Enabling boot devices in Computer Setup
- 169 Considering boot order changes
- 170 Choosing MultiBoot preferences
- 170 Setting a new boot order in Computer Setup
- 171 Dynamically choosing a boot device using the F9 prompt
- 171 Setting a MultiBoot Express prompt
- 171 Entering MultiBoot Express preferences
- 172 Management and printing
- 172 Using Client Management Solutions
- 172 Configuring and deploying a software image
- 173 Managing and updating software
- 173 HP Client Manager for Altiris (select models only)
- 175 HP CCM (Client Configuration Manager) (select models only)
- 176 HP SSM (System Software Manager)
- 177 Using the HP Universal Print Driver
- 178 Index