Backyard Discovery 65011 swing set Owner's Manual

Prescott
Wo o d e n S w i n g S e t
Model: #65011
••
••
••
••
Owner's Manual
Frequently Asked Questions
Assembly Instructions
Warranty Information
Manufacturer: Backyard Discovery
3001 North Rouse
Pittsburg, KS 66762
1-800-856-4445
Register your new swing set on-line @ www.swingsetsonline.com
(you will also find any updates on assembly instructions and
information to order replacement parts)
Features the
fastening system.
Save this assembly manual for future reference in the event that
you need to order replacement parts.
INS-65011-08-ENG-Prescott 5/29/12
Made in China
STOP
PARE
Missing A Part?
CALL US BEFORE GOING
BACK TO THE STORE!
The store where you made your purchase
does not stock parts for this item.
If you have assembly questions or if you need parts,
whether they are missing or damaged
Call Toll-Free Help Line or visit www.swingsetsonline.com
¡LLÁMENOS ANTES DE REGRESAR A LA TIENDA!
La tienda donde realizó la compra no almacena piezas de este producto.
Si tiene preguntas sobre el ensamblaje o si necesita piezas debido a que
faltan o están dañadas
llame gratis a la línea de ayuda
1-800-856-4445
PLEASE READ THIS BEFORE STARTING ASSEMBLY
POR FAVOR LEA ESTAS INSTRUCCIONES ANTES DE COMENZAR EL ENSAMBLAJE
•
•
•
•
•
•
•
•
•
•
READ THE ASSEMBLY MANUAL COMPLETELY, PAYING SPECIAL ATTENTION TO THE IMPORTANT TIPS AND
SAFETY INFORMATION.
AFTER YOU HAVE READ THE ASSEMBLY MANUAL, YOU WILL BE ABLE TO DECIDE IF YOU NEED PROFESSIONAL
HELP TO COMPLETE THE ASSEMBLY OF THE PLAYSET.
SEPARATE AND IDENTIFY ALL PARTS TO MAKE SURE THAT YOU HAVE ALL OF THE PARTS LISTED.
IF YOU CAN’T FIND ALL OF THE PARTS, CHECK THE PACKING MATERIAL. SMALL PARTS MAY HAVE FALLEN INTO IT
DURING SHIPMENT.
IF YOU HAVE PROBLEMS WITH THE ASSEMBLY OR IF ANY PART IS MISSING OR
DAMAGED, PLEASE CALL THE
HELP LINE 1-800-856-4445 OR VISIT www.swingsetsonline.com
LEA EL MANUAL DE ENSAMBLAJE COMPLETAMENTE, PRESTANDO ESPECIAL ATENCIÓN A LOS CONSEJOS ÚTILES
IMPORTANTES Y A LA INFORMACIÓN SOBRE SEGURIDAD.
DESPUÉS DE QUE HAYA LEÍDO EL MANUAL DE ENSAMBLAJE, PODRÁ DECIDIR SI NECESITA AYUDA PROFESIONAL
PARA EFECTUAR EL ENSAMBLAJE DE LA UNIDAD DE JUEGOS.
SEPARE E IDENTIFIQUE TODAS LAS PIEZAS PARA COMPROBAR QUE DISPONE DE TODAS LAS PARTES INDICADAS.
SI NO PUEDE ENCONTRAR TODAS LAS PIEZAS, REVISE EL MATERIAL DE EMPAQUE. ES POSIBLE QUE ALGUNAS
PIEZAS PEQUEÑAS PUEDAN HABERSE CAÍDO ALLÍ DURANTE EL ENVÍO.
SI TIENE PROBLEMAS CON EL ENSAMBLAJE O SI ALGUNA PIEZA FALTA O ESTÁ DAÑADA, LLAME A LA LÍNEA DE
AYUDA AL 1-800-856-4445 O VISITE www.swingsetsonline.com
PLEASE HAVE THE FOLLOWING INFORMATION WHEN YOU MAKE YOUR CALL:
1 – MODEL NUMBER OF THE PRODUCT LOCATED ON THE FRONT OF THE ASSEMBLY MANUAL
2 – DESRIPTION OF THE PART FROM THE PARTS LIST
POR FAVOR TENGA VISIBLE LA SIGUIENTE INFORMACIÓN CUANDO LLAME:
1 - NÚMERO DE MODELO DEL PRODUCTO QUE SE ENCUENTRA UBICADO AL FRENTE DEL MANUAL
DE ENSAMBLAJE
2 - DESCRIPCIÓN DE LA PIEZA QUE SE ENCUENTRA EN LA LISTA DE PIEZAS
Owner’s Manual Play Set
Dear Customer:
Please read entire booklet completely before beginning the assembly process.
Equipment is recommended for use by children 3 to 10 years of age. Structures are not intended for public use.
The Company does not warranty any of its residential structures subjected to commercial use such as:
Daycare, Preschool, Nursery School, Recreational Park, or any similar Commercial Application.
WARNING: This Symbol points out important safety instructions which, if not followed, could endanger
the personal safety of yourself and your children and/or damage your property. You MUST read and
follow all instructions in this manual before attempting to use this playcenter.
WARNING: Children must NOT use this playcenter until unit has been completely assembled
and inspected by an adult to insure set has been properly installed and anchored.
Please follow all recommendations below. Failure to do so may result in the warranty being void and/or safety
violations that could result in serious injury. This manual contains helpful information concerning Assembly
Preparation, Installation Procedure, and Required Maintenance. Always keep the safety of your children in mind as
your play structure is being built and as your children play on the set. Before your children play on the set please
review the Operation Instructions with them to help ensure their safety.
PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. KEEP THEM IN A SAFE PLACE WHERE YOU CAN
REFER TO THEM AS NEEDED. IN ORDER TO PROVIDE YOU WITH THE MOST EFFICIENT SERVICE, IT IS REQUIRED THAT
YOU PROVIDE US WITH THE PART NUMBERS WHEN ORDERING PARTS.
For Your Records:
Please take time and fill out the information below. This information will be needed for warranty issues.
Where Purchased: ____________________
Date of Purchase: ____________________
Installation Date: _____________________
Installed by: _________________________
Tracking Number: ____________________
Staple Receipt Here
Tracking Number Reference Label
Tracking ID number on the carton and back of the ID plate are included for tracking purposes
associated with warranty claims.
Rev5/09/12
Owner’s Manual Play Set
Please refer to the Assembly section of the Assembly Manual for Maximum Fall Height.
Positioning Your Playcenter
1. The Playcenter is designed to be installed on a level surface by an Adult with an Adult
helper. Place in a flat area of your yard to minimize ground preparation.
2. Choose a level location for the equipment. This can reduce the likelihood of the play set
tipping over and loose-fill surfacing material washing away during heavy rains.
3. Place the equipment not less than 6 ft (1.8 m) from any structure or obstruction such as a
fence, garage, house, overhanging branches, laundry lines, or electrical wires.
4. Provide enough room so that the children can use the equipment safely. For example, for
structures with multiple play activities, a slide should not exit in front of a swing.
5. It is a good idea to place your Playcenter in an area that is convenient for adults to watch
children at play.
6. Create a site free of obstacles that could cause injuries – such as low overhanging tree
branches, overhead wires, tree stumps and/or roots, large rocks, bricks and concrete.
Additional suggestions in the Suggested Playground Surfacing Section.
7. Do not build your playset on top of surfacing material.
8. Locate bare metal platforms and slides out of direct sunlight to reduce the likelihood of serious
burns. A slide that faces north will receive the least direct sunlight.
9. Separate active and quiet activities from each other. For example, locate sandboxes away
from swings or use a guardrail or barrier to separate the sandbox from the movement of the
swings.
Suggested Playground Surfacing
Do not install home playground equipment over concrete, asphalt, packed earth, grass, carpet,
or any other hard surface. A fall onto a hard surface can result in serious injury to the
equipment user.
Do not install loose fill surfacing over hard surfaces such as concrete or asphalt.
Shredded bark mulch, wood chips, fine sand and fine gravel, are added as shock absorbing
materials after assembly. If used properly these materials can absorb some of the impact of a
child’s fall.
All surface material should extend a minimum of 6 feet in all directions around the play area.
Do not apply playground surfacing until after the unit is completely constructed. Playset should
not be built on top of surfacing.
Use containment, such as digging out around the perimeter and/or lining the perimeter with
landscape edging.
Installations of rubber tiles or poured-in-place surfaces (other than loose-fill materials)
generally require a professional and are not “do-it-yourself” projects.
Shall use Playground Surfacing Materials (other than loose-fill material) which comply with the
safety standard ASTM F1292 Standard Specification of Impact Attenuation of Surfacing
Materials within the Use Zone of Playground Equipment.
Rev5/09/12
Owner’s Manual Play Set
The following chart explains the fall height in feet from which a life threatening head injury
would not be expected
Critical Heights in feet (m) of Tested Materials
Material
Uncompressed Depth
Compressed Depth
Wood Chips
Double-Shredded bark mulch
Engineered Wood Fibers
Fine Sand
Coarse Sand
Fine Gravel
Medium Gravel
6" (152mm)
7' (2.13m)
6' (1.83m)
6' (1.83m)
5' (1.52m)
5' (1.52m)
5' (1.52m)
5' (1.52m)
9" (228mm)
10' (3.05m)
10' (3.05m)
7' (2.13m)
5' (1.52m)
5' (1.52m)
7' (2.13m)
5' (1.52m)
12" (304mm)
11' (3.35m)
11' (3.35m)
>12' (3.66m)
9' (2.74m)
6' (1.83m)
10' (3.05m)
6' (1.83m)
to 9" (228mm)
10' (3.05m)
7' (2.13m)
6' (1.83m)
5' (1.52m)
4' (1.22m)
6' (1.83m)
5' (1.52m)
Shredded Tires*
10-12' (3.0-3.6m)
N/A
N/A
N/A
*This data is from tests conducted by independent testing laboratories on a 6-inch depth of uncompressed shredded tire samples produced by four manufacturers. The tests
reported critical heights, which varied from 10 feet to greater than 12 feet. It is recommended that persons seeking to install shredded tires as a protective surface request test
data from the supplier showing the critical height of the material when it was tested in accordance with ASTM F1292.
Operating Instructions:
NOTE: Your children’s safety is our #1 concern. Observing the following statements
and warnings reduces the likelihood of serious or fatal injury. Please review these
safety rules regularly with your children.
1. This Playcenter is designed for specific number of occupants whose combined weight should
not exceed a designated weight on the elevated floor or the swing area, the total Unit capacity
is outlined in the Basic Setup Dimensions section of instruction manual. The maximum fall
height and recommended play area is also available in the Basic Setup Dimensions section of
the manual for the specific unit.
2. On-site adult supervision is required.
3. Instruct children not to walk close to, in front of, behind, or between moving swings or other
moving playground equipment.
4. Instruct children to sit in and never stand on swings
5. Instruct children not to twist the chains and ropes and not to loop them over the top support
bar, since this may reduce the strength of the chain or rope.
6. Instruct children not to jump from swings or other playground equipment in motion.
7. Instruct children to not to push empty seats. The seat may hit them and cause serious injury.
8. Instruct and teach children to sit in the center of the swings with their full weight on the seats.
9. Instruct children not to use the equipment in a manner other than intended.
10. Instruct children to always go down slides feet first. Never slide head first.
11. Instruct children to look before they slide to make sure no one is at the bottom.
12. Instruct children to never run up a slide, as this increases their chances of falling.
13. The parents should dress children appropriately. (Examples would include the use of wellfitting shoes and the avoidance of ponchos, scarfs, and other loose-fitting clothing that is
potentially hazardous while using equipment).
14. Instruct children not to climb when the equipment is wet.
15. Instruct children to never jump from a fort deck. They should always use the ladder, ramp or
slide.
16. Instruct children to never crawl or walk across the top of monkey bars.
17. Instruct children to never crawl on top of a fort roof.
Rev5/09/12
Owner’s Manual Play Set
18. Verify that any suspended climbing ropes, chain, or cable are secured at both ends and that
they cannot be looped back on it.
19. Instruct children not to attach items to the playground equipment that are not specifically
designed for use with the equipment, such as, but not limited to, jump ropes, clothesline, pet
leashes, cables and chain as they may cause a strangulation hazard.
20. Instruct children to never wrap their legs around swing chain.
21. Instruct children to never slide down the swing chain.
22. Instruct children to remove their bike or other sports helmet before playing on playground
equipment.
Maintenance Instructions:
At the beginning of each play season:
• Tighten all hardware.
• Lubricate all metallic moving parts per manufacturer’s instructions.
• Check all protective coverings on bolts, pipes, edges, and corners. Replace if they are loose,
cracked, or missing.
• Check all moving parts including swing seats, ropes, cables, and chains for wear, rust, or
other deterioration. Replace as needed.
• Check metal parts for rust. If found, sand and repaint using a non Lead-based paint meeting
the requirements of 16 CFR 1303.
• Check all wood members for deterioration and splinters. Sand down splinters and replace
deteriorating wood members.
• Reinstall any plastic parts, such as swing seats or any other items that were removed for the
cold season.
• Rake and check depth of loose fill protective surfacing materials to prevent compaction and
to maintain appropriate depth. Replace as necessary.
Twice a month during play season:
• Tighten all hardware.
• Check all protective coverings on bolts, pipes, edges, and corners. Replace if they are loose,
cracked, or missing.
• Rake and check depth of loose fill protective surfacing materials to prevent compaction and
to maintain appropriate depth. Replace as necessary.
• Once a month during play season.
• Lubricate all metallic moving parts per manufacturer’s instructions.
• Check all moving parts including swing seats, ropes, cables, and chains for wear, rust, or
other deterioration. Replace as needed.
At the end of each play season or when the temperature drops below 32° F:
• Remove plastic swing seats and other items as specified by the manufacturer and take
indoors or do not use.
• Rake and check depth of loose fill protective surfacing materials to prevent compaction and
to maintain appropriate depth. Replace as necessary.
Rev5/09/12
Owner’s Manual Play Set
Additional Maintenance:
• Check the swing beam and hardware every two weeks due to wood expansion and
contraction. It is particularly important that this procedure be followed at the beginning of each
season.
• Inspect wood parts monthly. The grain of the wood sometimes will lift in the dry season
causing splinters to appear. Light sand may be necessary to maintain a safe playing
environment. Treat your playset with stain regularly, to help prevent severe checking/splitting
and other weather damage.
• A waterbourne transparent stain has been applied to your playset. This is done for color only.
Once or twice a year, depending on your climate conditions, you must apply some type of
protection (sealant) to the wood of your unit. Prior to the application of sealant, lightly sand any
“rough” spots on your playset. Please not this is a requirement of your warranty.
• Assembling and maintaining the playset on a level location is very important. As your children
play, your playset will slowly dig its way into the soil, and it is very important that it settles
evenly. Make sure the playset is level and true one each year or at the beginning of each play
season.
Disposal Instructions:
When the Playcenter use is no longer desired, it should be disassembled and disposed of in such a
way that no unreasonable hazards will exist at the time the unit is discarded.
Third Party Assembly:
Customer may, in their sole discretion, elect to use a third party person or service to assemble this
product. Backyard Discovery assumes no responsibility or liability for any charge incurred by the
Customer for any assembly services’.
Please see our warranty for more information about damaged and missing part replacement
coverage. Backyard Discovery will not reimburse Customer for the price of parts purchased.
Rev5/09/12
Owner’s Manual Play Set
APPENDIX A
Information on Playground Surfacing Materials:
The following information is from the United States Consumer Product Safety Commission’s
Information Sheet for playground surfacing material; also see the following website for additional
information: www.cpsc.gov/cpscpub/pubs/323.html.
X3. SECTION 4 OF THE CONSUMER PRODUCT SAFETY COMMISSION’S OUTDOOR HOME PLAYGROUND SAFETY
HANDBOOK9
X3.1 Select Protective Surfacing—One of the most important things you can do to reduce the likelihood of
serious head injuries is to install shock-absorbing protective surfacing under and around your play equipment. The
protective surfacing should be applied to a depth that is suitable for the equipment height in accordance with ASTM
Specification F 1292. There are different types of surfacing to choose from; whichever product you select, follow these
guidelines:
X3.1.1 Loose-Fill Materials:
X3.1.1.1 Maintain a minimum depth of 9 inches of loose-fill materials such as wood mulch/chips, engineered
wood fiber (EWF), or shredded/recycled rubber mulch for equipment up to 8 feet high; and 9 inches of sand or pea
gravel for equipment up to 5 feet high. NOTE: An initial fill level of 12 inches will compress to about a 9-inch depth of
surfacing overtime. The surfacing will also compact, displace, and settle, and should be periodically refilled to maintain at
least a 9-inch depth.
X3.1.2 Use a minimum of 6 inches of protective surfacing for play equipment less than 4 feet in height. If
maintained properly, this should be adequate. (At depths less than 6 inches, the protective material is too easily
displaced or compacted.) NOTE: Do not install home playground equipment over concrete, asphalt, or any other hard
surface. A fall onto a hard surface can result in serious injury to the equipment user. Grass and dirt are not considered
protective surfacing because wear and environmental factors can reduce their shock absorbing effectiveness. Carpeting
and thin mats are generally not adequate protective surfacing. Ground level equipment such as a sandbox, activity wall,
playhouse or other equipment that has no elevated play surface – does not need any protective surfacing.
X3.1.3 Use containment, such as digging out around the perimeter and/or lining the perimeter with landscape
edging. Don’t forget to account for water drainage.
X3.1.3.1 Check and maintain the depth of the loose-fill surfacing material. To maintain the right amount of loosefill materials, mark the correct level on play equipment support posts. That way you can easily see when to replenish
and/or redistribute the surfacing.
X3.1.3.2 Do not install loose-fill surfacing over hard surfaces such as concrete or asphalt.
X3.1.4 Poured-In-Place Surfaces or Pre-Manufactured Rubber Tiles — You may be interested in using surfacing
other than loose-fill materials – like rubber tiles or poured-in-place surfaces.
X3.1.4.1 Installations of these surfaces generally require a professional and are not “do-it-yourself” projects.
X3.1.4.2 Review surface specification before purchasing this type of surfacing. Ask the installer/manufacturer for
a report showing that the product has been tested to the following safety standard: ASTM F 1292 Standard Specification
for Impact Attenuation of Surfacing Materials within the Use Zone of Playground Equipment. This report should show the
specific height for which the surface is intended to protect against serious head injury. This height should be equal to or
greater than the fall height – vertical distance between a designated play surface (elevated surface for standing, sitting, or
climbing) and the protective surfacing below – of your play equipment.
X3.1.4.3 Check the protective surfacing frequently for wear.
X3.1.5 Placement — Proper placement and maintenance of protective surfacing is essential. Be sure to:
X3.1.5.1 Extend surfacing at least 6 feet from the equipment in all directions.
X3.1.5.2 For to-fro swings, extend protective surfacing in front of and behind the swing to a distance equal to
twice the height of the top bar from which the swing is suspended.
9
This information has been extracted from the CPSC publications “Playground Surfacing — Technical
Information Guide” and “Handbook for Public Playground Safety.” Copies of these reports can be obtained by sending a
postcard to the: Office of Public Affairs, U.S. Consumer Product Safety Commission, Washington, D.C., 20207 or call the
toll-free hotline: 1-800-638-2772.
Rev5/09/12
Owner’s Manual Play Set
The American Society for Testing and Materials takes no position respecting the validity of any parent right
asserted in connection with any item mentioned in this standard. Users of this standard are expressly advised that
determination of the validity of any such parent rights, and the risk of infringement of such rights, are entirely their own
responsibility.
The standard is subject to revision at any time by the responsible technical committee and must be reviewed
every five years and if not revised, either approved or withdrawn. Your comments are invited either for revision of this
standard or for additional standards and should be addressed to ASTM Headquarters. Your comments will receive
careful consideration at a meeting of the responsible technical committee, which you may attend. If you feel that your
comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards.
100 Barr Harbor Drive, West Conshohocken, PA 19428.
Rev5/09/12
Play Set Assembly Manual FAQs:
1. Does the area for the playset need to be level?
Yes. Backyard Discovery recommends the playset be positioned on a flat level area for
maximum safety and durability. The stakes provided should be used to secure it firmly to the
ground.
2. What size area is recommended for the playset?
Backyard Discovery recommends at least a 6’ (six foot) perimeter around and above the playset
for maximum safety.
3. What age range is appropriate for the playsets?
Backyard Discovery playsets are recommended for children ages 3 – 10 years.
4. Is the wood treated with chemicals?
Backyard Discovery uses 100% Chinese Cedar wood which is naturally bug resistant, decay
and rot resistant. To help ensure your child’s safety, our wood is completely chemical free and
we do not use pressure-treated wood. The stain we use is a top coat using a water-based
product that is for appearance only.
5. How often should the playset be stained?
Backyard Discovery recommends the playset be stained once each year. A water or oil based
stain can be used at the customer’s discretion.
6. Why does it seem that my swing set is developing cracks?
Wood is a natural material; no two pieces are exactly alike. Each piece has its own
characteristics and personality and reacts differently to climate changes. When any wood
product is exposed to the elements, it develops “wood checks”. A check is the radial separation
of the wood fibers running with the grain of the wood. These are caused by the varying
temperature and moisture conditions. A check is not a crack – it does not affect the strength or
durability of the wood or structural integrity of the play set.
7. Do Backyard Discovery playsets come with a warranty?
Yes. All Backyard Discovery products carry a 1-year replacement warranty on all parts for
manufacturer’s defect. Our wood carries a 5 year warranty on rot and decay as well. Please see
warranty details for more information.
8. What is the best way to get started assembling the playset?
Backyard Discovery recommends taking all the parts out of the boxes and arranging them by
part number before you begin any assembly. This will not only allow faster assembly, but will
also identify any parts that may be missing or damaged so they can be replaced before
assembly. If parts are missing or need replacement, go to
Rev5/20/10 BRS www.swingsetsonline.com/support.aspx and follow the prompts to order them. Next, read the
assembly manual and get the tools ready for the job as
recommended in the manual. If the assembly manual is lost or misplaced a new one can be
printed from Backyard Discovery’s website: www.swingsetsonline.com.
9. The playset seems to rock or sway too much. What’s wrong?
Rocking is caused by uneven ground or obstructions such as rocks, roots, etc. under the ground
rails. These should be removed and the ground underneath re-leveled to prevent rocking. Also
ensure the playset is securely staked to the ground using the stakes provided.
10. The 2”x4” boards do not measure 2”x 4”. Why not?
In the U.S. it is common practice to describe lumber dimensions using the rough cut sizes from
the sawmill and not the finished dimensions. Retailers, home stores, etc. all use this accepted
practice for describing lumber dimensions. However, Backyard Discovery playsets are designed
and constructed using the actual dimensions so everything fits properly and remains so during
the life of the playset.
11. The end beam is not straight up and down. Why not?
This is normal. Backyard Discovery designs playsets this way to ensure the strongest structure
possible. The slight angle adds strength and reduces rocking and twisting.
12. The S-hooks for the swings won’t close. What is wrong?
Backyard Discovery recommends placing them on a hard surface such as concrete (don’t do
this on anything that will dent such as metal or finished wood or glass which will break!). It will
take quite a few strokes, but the hooks will close.
For more information and frequently asked questions, please refer to our website at
www.swingsetsonline.com. Rev5/20/10 BRS Tools Required for Installation:
(These are the tools that are generally required for assembly of our outdoor products.
These tools are not included in the outdoor product purchase.)
(Square)
(Level 24")
(Open End Wrenches 1/2")
(Tape Measure)
(Drive Ratchet, 1/2" STD
Sockets & 1/2" Deep Sockets)
(Claw Hammer)
(Drill Attachments: Phillips
(Cordless Drill or Electric Drill) (3/16", 5/16", 3/8" & 1/8" Drill Bits) Head & Socket Driver)
(An Adult w/ an Adult Helper)
(Phillips & Straight
Blade Screw Drivers)
Ladder (Optional)
(Rubber Mallet - Optional)
Basic Setup Dimensions
Place the set on level ground, not less than 6 ft [2 m] from any structure or obstruction such
as a fence, garage, house, overhanging branches, laundry lines, or electrical wires.
72"
Safe Play Zone
98 3/8"
140"
128 3/16"
General Information:
Your set has been designed and engineered for
children only and for residential use only.
A maximum of 150 lbs. per child is recommended for
play activities designed for individual use.
A maximum of 120 lbs. per child is recommended for
play activities designed for multiple child use.
A maximum of 5 children is recommended for this
swing set.
Important Assembly Notes
Safe play height: 8'-2 1/4" [2.5 m]
Maximum fall height: 6'-3 5/16" [1.9 m]
1) While assembling unit, take time before and after each phase to make sure fort is level. If fort is
not level, assembly will be difficult and improper assembly may result. Extra care must be taken to
insure the fort is square.
2) Pay close attention to the ITEMS NEEDED FOR EACH PHASE. They can be a valuable aid when
sorting your wood and hardware. Assembly will be made easier if items are sorted by phase.
3) Pay close attention to make sure you are using the correct hardware in the correct phases. Using
incorrect hardware may result in improper assembly.
4) Whenever a T-nut is used, follow these directions. Place T-nut in pre-drilled hole. Tap in with hammer.
Place bolt with washers in the opposite side. Hand tighten to make sure the bolt is in the T-nut.
DO NOT over tighten.
5) Read the steps of each phase thoroughly. The written steps may include important information not
shown in the illustrations.
Parts Identification
Wood Components
(NOT TO SCALE)
E1 - FORT UPRIGHT - W101847
(2) 1 3/8"x3 3/8"x85 5/8" (36.0x86.0x2176.0)
E2 - FORT UPRIGHT - W101139
(2) 1 3/8"x3 3/8"x85 5/8" (36.0x86.0x2176.0)
E77 - ANGLE BRACE - W100991
(2) 1 3/8"x3 3/8"x74 3/8" (36x86x1890)
G1 - TARP SWING BEAM CROSS BRACE - W101153
(1) 1"x5 1/4"x46 1/2" (24.0x134.0x1182.0)
G2 - TARP CROSS BRACE - W101142
(1) 1"x5 1/4"x46 1/2" (24.0x134.0x1182.0)
H1 - WALL RAIL - W101848
(2) 1"x3 3/8"x49 3/8" (24x86x1255.241)
H2 - TARP UPRIGHT - W101144
(2) 1"x3 3/8"x20 1/4" (24.0x86.0x514.0)
H3 - FLOOR BRACE - W101844
(2) 1"x3 3/8"x54 3/4" (24.0x86.0x1392.0)
H4 - WALL RAIL - W101849
(2) 1"x3 3/8"x35 1/4" (24x86x896.366)
H79 - END SUPPORT - W100992
(1) 1"x3 1/2"x42" (24x86x1072)
H80 - GROUND BOARD - W100990
(1) 1"x3 3/8"x87 3/8" (24x86x2218)
Parts Identification
Wood Components
(NOT TO SCALE)
K1 - TARP END CAP - W101851
(2) 5/8"x5 1/4"x23 3/4" (16.0x134.0x603.0)
L2 - FLOOR BOARD - W101855
(2) 5/8"x4 3/8"x53 3/4" (16.0x112.0x1366.0)
M1 - GROUND BOARD - W101846
(2) 5/8"x3 3/8"x85 1/2" (16.0x86.0x2172.0)
M2 - FLOOR BOARD - W101854
(3) 5/8"x3 3/8"x53 3/4" (16x86x1366)
M3 - WALL SLAT - W101850
(6) 5/8"x3 3/8"x19 3/8" (16x86x493)
M4 - ROCK WALL SLAT - W101890
(6) 5/8"x3 3/8"x21 7/8" (16x86x555)
M5 - TOP TARP BOARD - W103290
(1) 5/8"x3 3/8"x21 7/8" (16x86x555)
M72 - ROCK WALL SLAT - W101852
(3) 5/8"x3 3/8"x21 7/8" (16x86x555)
M77 - SLIDE BRACE - W100544
(1) 5/8"x3 3/8"x17 1/4" (16x86x438)
M78 - CENTER SLIDE BRACE - W100545
(2) 5/8"x3 3/8"x17 1/4" (16x86x438)
N1 - FLOOR SUPPORT - W101853
(3) 5/8"x2 3/8"x17 1/8" (16.0x60.0x435.0)
N2 - SWING BLOCK SAFETY RAIL - W101845
(1) 5/8"x2 3/8"x66 1/8" (16x60x1680)
SB70 - SWING BEAM - W100955-A
(1) 2"x5 1/4"x89 1/2" (50x134x2274)
W70 - SWING BEAM SUPPORT - W100956-A
(1) 2"x3 3/8"x45 7/8" (50x86x1165)
Parts Identification
Hardware
(5) AJ - BOLT HEX 5/16x1-1/4 - H100042
(7) A - BOLT FA 3/8x1-1/2 - H100001
(3) AN - BOLT HEX 5/16x2-3/4 - H100047
(7) BG - T-NUT 5/16 - H100074
(3) Z - LAG SCREW WH 5/16x2 - H100027
(38) AD - WASHER LOCK EXT 12x19 - H100031
(7) BF - T-NUT 3/8 - H100073
(7) CM - BOLT WH 5/16x1/2 - H100115
(14) CY - SCREW PWH 8x5/8 - H100128
(32) AC - WASHER LOCK EXT 8x19 - H100030
(7) H - BOLT WH 5/16x1-1/2 - H100010
(7) B - NUT BARREL WH 5/16x5/8 - H100004
(4) J - BOLT WH 5/16x1-3/4 - H100011
(19) K - BOLT WH 5/16x2 - H100012
(29) D - NUT BARREL WH 5/16x7/8 - H100005
(2) M - BOLT WH 5/16x2-1/2 - H100014
(3) C - NUT BARREL WH 5/16x1-1/2 - H100006
(1) KA - BOLT WH 5/16x4-1/2 - H100021
Parts Identification
Hardware
(4) CH - SCREW TAPPING 14x1-1/2 - H100109
(4) CG - WASHER LOCK INT 8x15 - H100108
(13) BL - SCREW TAPPING 14x3/4 - H100083
(4) CE - WASHER FLAT 9x18 - H100106
(26) BP - SCREW PFH 8x1-1/2 - H100086
(5) BS - SCREW PFH 8x1-3/4 - H100089
(24) CK - SCREW PFH 8x2 - H100111
(52) BV - SCREW PFH 8x2-1/4 - H100091
(26) BW - SCREW PFH 8x3 - H100092
(9) CB - WASHER SAFETY 17x30 - H100103
(15) CD - WASHER FLAT 8x27 - H100105
(9) CJ - NUT LOCK 5/16 - H100110
(6) BZ - SWING HANGER QUICK LINK - H100099
(39) BR - SCREW PFH 8x1-1/8 - H100088
(5) BX - WASHER SPLIT 5/16 - H100095
(2) - T-40 Torx Wrench - A100041
(2) - T-40 Torx Bit - A100042
Parts Identification
Accessories
(NOT TO SCALE)
(1) EK - SLIDE RAIL 8' GREEN RIGHT - A100054
HC - BYD ID TAG (LARGE) 2011 WITH
(1) AGES
-A100164
(1) EL - SLIDE RAIL 8' GREEN LEFT - A100055
(1) EM - SLIDE BED 8' YELLOW - A100056
(2) DP - SWING SEAT GREEN - A100027
(4) FA - QUICK LINK
-A100069
(2) QZ - TRIANGLE PLATE 100 5 HOLE - A100294
(6) ER - CLIMBING ROCK GREEN SMALL
-A100060
(2) GD - L BRACKET 66x66x127
-A100140
(6) KD - PLASTIC GROUND STAKE BROWN - A100179
(1) NL - FORT TARP - A100258
(6) EJ - L BRACKET 54x67
-A100053
(1) TU - TRAPEZE ASSEMBLY WITH 31" GREEN CHAIN - A100111
(4) EZ - CHAIN GREEN 51.25" - A100068
(2) EA - HAND GRIP YELLOW PLASTIC - A100043
8 FOOT SLIDE ASSEMBLY
PHASE 1
Phase Notes
TOP
● DRILL 3 HOLES AT ONE END OF THE PLASTIC SLIDE BED USING A 5/16" DRILL BIT AND USING THE
DIMENSIONS SHOWN BELOW. THIS END WILL BE THE TOP OF THE SLIDE.
● TAKE NOTE OF SLIDE BED SURFACE FINISH, THE DULL SIDE WILL BE TOWARDS THE GROUND. PLACE
SLIDE BRACE CENTERED ON THE BOTTOM (DULL SIDE) AND 1/4" FROM THE EDGE. TRANSFER HOLES
ON THE BOARD THROUGH THE SLIDE BED AS SHOWN BELOW. USE A 5/16" DRILL BIT.
● ATTACH SLIDE BRACE TO SLIDE USING HARDWARE SHOWN.
BRIGHT SIDE
QTY
1
3
3
3
1
TOP
13 5/8
8 5/8
3 5/8
DESCRIPTION
SLIDE BRACE
BOLT WH 5/16x1/2
NUT BARREL WH 5/16x5/8
WASHER LOCK EXT 12x19
SLIDE BED 8' YELLOW
1
BOTTOM
SLIDE BED 8' YELLOW
NUT BARREL WH 5/16x5/8
WASHER LOCK EXT 12x19
SLIDE BRACE
BOLT WH 5/16x1/2
TIP: PREBENDING THE ENDS WILL EASE ASSEMBLY.
REV 5/26/10 BRS
8 FOOT SLIDE ASSEMBLY
PHASE 2
Phase Notes
● PLACE 1 SLIDE RAIL ON A FLAT SURFACE AND BEGIN INSERTING SLIDE BED AT THE BOTTOM OF THE
SLIDE RAIL. PUT SLIDE SUPPORT BOTTOM INTO THE SUPPORT POCKET AT THE BOTTOM OF THE
RAIL AND HAVE A HELPER BEND THE SLIDE BED TOWARDS THE TOP OF THE SLIDE AND INSERT
THE BED INTO THE SLIDE CAVITY. MAKE SURE SLIDE BED IS COMPLETELY DOWN IN THE SLIDE
CAVITY.
● PLACE THE OTHER SLIDE RAIL ON A FLAT SURFACE WITH THE SLIDE CAVITY UP. HAVE A HELPER
HOLD THE TOP END OF SLIDE BED AND BEGIN INSERTING THE SLIDE BED AND SLIDE BRACES INTO
THE CAVITY AND SUPPORT POCKETS STARTING AT THE BOTTOM OF SLIDE AND WORKING UP TO
THE TOP.
● ONCE BED AND BRACES ARE COMPLETELY IN THE CAVITY AND IN THE SUPPORT POCKETS, SECURE
USING 3" SCREWS AT EACH OF THE PILOT HOLE LOCATIONS AS SHOWN BELOW.
SLIDE RAIL 8' GREEN RIGHT
CENTER SLIDE BRACE
SLIDE RAIL 8' GREEN LEFT
QTY
DESCRIPTION
2
24
1
1
CENTER SLIDE BRACE
SCREW PFH 8x3
SLIDE RAIL 8' GREEN RIGHT
SLIDE RAIL 8' GREEN LEFT
SCREW PFH 8x3
TIP: A HELPER IS REQUIRED FOR THIS PHASE.
4 Ft Swing Beam
Phase 1
Phase Notes
• Assemble
with hardware as shown.
CD
GD
AN
CD
CD
CJ
SB70
CD
J
AD
D
AD
QZ
QTY
4
2
2
2
1
2
2
2
2
DESCRIPTION
WASHER FLAT 8x27
NUT LOCK 5/16
L BRACKET 66x66x127 GREEN
BOLT HEX 5/16x2-3/4
SWING BEAM
NUT BARREL WH 5/16x7/8
WASHER LOCK EXT 12x19
TRIANGLE PLATE 100 5 HOLE
BOLT WH 5/16x1-3/4
LABEL
CD
CJ
GD
AN
SB70
D
AD
QZ
J
4 Ft Swing Beam
Phase 2
Phase Notes
W70
AC
AD
• Assemble with hardware as shown.
M
C
AC
AD
D
AD
AC
KA
AC
K
H79
AD
D
AC
K
Z
AC
E77
D
AD
E77
AC
AD
K
D
H80
AC
QTY
2
7
4
2
5
2
9
1
2
1
1
1
DESCRIPTION
LAG SCREW WH 5/16x2
WASHER LOCK EXT 12x19
BOLT WH 5/16x2
BOLT WH 5/16x2-1/2
NUT BARREL WH 5/16x7/8
NUT BARREL WH 5/16x1-1/2
WASHER LOCK EXT 8x19
BOLT WH 5/16x4-1/2
ANGLE BRACE
END SUPPORT
GROUND BOARD
SWING BEAM SUPPORT
LABEL
Z
AD
K
M
D
C
AC
KA
E77
H79
H80
W70
D
AD
K
4 Ft Swing Beam
Phase 3
Phase Notes
• Assemble with hardware as shown.
AD
J
D
AD
QTY
2
2
2
DESCRIPTION
NUT BARREL WH 5/16x7/8
WASHER LOCK EXT 12x19
BOLT WH 5/16x1-3/4
LABEL
D
AD
J
4 Ft Swing Beam
Phase 4
Phase Notes
• Assemble with hardware as shown.
QTY
6
6
6
6
DESCRIPTION
WASHER FLAT 8x27
NUT LOCK 5/16
SWING HANGER QUICK LINK
WASHER FLAT 17x30
CJ
CD
CB
BZ
LABEL
CD
CJ
BZ
CB
Fort Assembly
Phase 1
Parts needed:
Hardware needed:
• (2) E1 - FORT UPRIGHT - W101847
• (2) E2 - FORT UPRIGHT - W101139
• (2) H1 - FLOOR BRACE - W101848
• (2) H3 - FLOOR BRACE - W101844
• (2) M1 - GROUND BOARD - W101846
• (1) N2 - SWING BLOCK SAFETY RAIL - W101853
• (12) D - NUT BARREL WH 5/16x7/8 - H100005
• (12) AD - WASHER LOCK EXT 12x19 - H100031
• (12) AC - WASHER LOCK EXT 8x19 - H100030
• (8) K - BOLT WH 5/16x2 - H100012
• (4) H - BOLT WH 5/16x1-1/2 - H100010
• (8) CK - SCREW PFH 8x2 - H100111
• (4) BS - SCREW PFH 8x1-3/4 - H100089
Phase Notes
• Assemble with hardware as shown.
To prevent board splitting, you
must pre-drill each board with
a 1/8" drill bit, before attaching.
PILOT HOLES SHOULD
FACE OUTWARD ON
'E2' BOARDS.
Step 3: Pre-drill & attach 'H1'
Floor Brace to the outside of
'E1' & 'E2' Fort Uprights using
screws 'CK', as shown.
E2
E1
H1
CK
AD
D
AC
AD
K
AC
AC
K
AD
D
AD
H3
AC
E2
E2
H3
E1
E1
E1
Step 2: Level & attach 'H3' Floor Brace
to the inside of 'E1' & 'E2' Fort Uprights
using hardware 'D', 'AD', 'AC', & 'K', as
shown.
H1
E1
E1
H3
BS
AC
H
N2
H
M1
AD
AC
D
AD
M1
M1
M1
Step 4: Pre-drill & attach 'N2' Swing
Block Safety Rail to the outside of
'E1' & 'E2' Fort Uprights using screws
'BS', as shown.
Step 1: Attach 'M1' Ground Boards to the
outside of 'E1' & 'E2' Fort Uprights using
hardware 'D', 'AD', 'AC', & 'H', as shown.
Fort Assembly
Phase 2
Parts needed:
Hardware needed:
• (2) M72 - ROCK WALL SLAT - W100023
• (8) BV - SCREW PFH 8x2-1/4 - H100091
Phase Notes
• Assemble with hardware as shown.
Note: It is vital that the fort
be level before and after
each phase of assembly.
To prevent board splitting, you
must pre-drill each board with
a 1/8" drill bit, before attaching.
E2
E2
BV
Step 1: Pre-drill & attach 'M72' Rock
Wall Slat to the edges of 'E1' & 'E2' Fort
Uprights using hardware 'BV', as
shown.
M72
E1
M72
'E1' ends & 'M72' edge
should be flush.
BV
Fort Assembly
Phase 3
Parts needed:
Hardware needed:
• (3) M2 - FLOOR BOARD - W101143
• (3) N1 - FLOOR SUPPORT - W101152
• (2) L2 - FLOOR BOARD - W101855
• (6) EJ - L BRACKET GREEN 54X67 - A100053
• (30) BR - SCREW PFH 8x1-1/8 - H100088
• (12) BL - SCREW TAPPING 14x3/4 - H100083
Phase Notes
• Assemble with hardware as shown.
BL
Note: It is vital that the fort
be level before and after
each phase of assembly.
To prevent board splitting, you
must pre-drill each board with
a 1/8" drill bit, before attaching.
EJ
N1
EJ
BL
BR
N1
EJ
BL
N1
BR
L2
BR
L2
H3
M2
Step 1: Using 'N1' Floor Supports as a template,
pre-drill & attach Floor Supports 'N1' to Floor Boards
'M2' & 'L2' approximately 3 9/16" from both edges of
'M2' boards and center the remaining 'N1' support, as
shown. Attach N1 supports to 'M2' boards using
screws 'BR', as shown. Finally, secure L-Brackets 'EJ'
to 'N1' supports using screws 'BL', as shown.
BL
H3
EJ
Step 2: Attach Floor Assembly to 'H3' floor
braces using screws 'BL', as shown.
Fort Assembly
Phase 4
Hardware needed:
Parts needed:
• (6) BR - SCREW PFH 8x1-1/8 - H100088
• (6) A - BOLT FA 3/8x1-1/2 - H100001
• (28) BV - SCREW PFH 8x2-1/4 - H100091
• (6) BF - T-NUT 3/8 - H100073
• (6) M4 - ROCK WALL SLAT - W101890
• (1) M72 - ROCK WALL SLAT - W101852
• (6) ER - CLIMBING ROCK GREEN SMALL - A100060
Phase Notes
• Assemble with hardware as shown.
Step 1: Gather the (6) Rockwall Boards
'M4' and hammer 3/8" T-nuts 'BF' into
large hole on each board.
Slide Attachment End.
E1
Step 2: Attach 'ER' Climbing Rock
Green Small to each of the (6) Rockwall
Boards 'M4', using hardware 'A' & 'BR',
as shown.
E1
E2
E2
E2
M4
Last 'M4' slat
located under
deck boards.
BV
BF
ER
A
BR
N2
BV
'N2' saftey rail should
be located on Swing
Beam side of set.
BV
M4
Step 3: Pre-drill & attach 'M4' & 'M72'
Rock Wall Slats to 'E2' fort uprights, as
shown in picture, using screws 'BV'.
M4
M72
To prevent board splitting, you
must pre-drill each board with
a 1/8" drill bit, before attaching.
Note: It is vital that the fort
be level before and after
each phase of assembly.
Fort Assembly
Phase 5
Hardware needed:
Parts needed:
• (2) EA - HAND GRIP YELLOW PLASTIC - A100043
Phase Notes
• (4) CE - WASHER FLAT 9x18 - H100106
• (4) CG - WASHER LOCK INT 8x15 - H100108
• (4) CH - SCREW TAPPING 14x1-1/2 - H100109
• Assemble with hardware as shown.
To prevent board splitting, you
must pre-drill each board with
a 1/8" drill bit, before attaching.
E2
CE
CH
CG
EA
E1
E2
CH
CG
CE
EA
Step 1: Attach 'EA' Hand Grip Yellow
Plastic to 'E1' & 'E2' fort uprights, using
hardware 'CE', 'CG', & 'CH', as shown.
Fort Assembly
Phase 6
Parts needed:
Hardware needed:
• (2) D - NUT BARREL WH 5/16x7/8 - H100005
• (2) AD - WASHER LOCK EXT 12x19 - H100031
• (4) AC - WASHER LOCK EXT 8x19 - H100030
• (2) H - BOLT WH 5/16x1-1/2 - H100010
• (2) K - BOLT WH 5/16x2 - H100012
• (2) BG - T-NUT 5/16 - H100074
• (12) BV - SCREW PFH 8x2-1/4 - H100091
• (1) G1 - TARP SWING BEAM CROSS BRACE - W101153
• (1) G2 - TARP CROSS BRACE - W101142
• (2) H2 - TARP UPRIGHT - W101144
• (2) K1 - TARP END CAP - W101851
• (1) M5 - TARP TOP BOARD - W103290
Phase Notes
• Assemble with hardware as shown.
Note: It is vital that the fort
be level before and after
each phase of assembly.
To prevent board splitting, you
must pre-drill each board with
a 1/8" drill bit, before attaching.
Step 1: Attach Tarp Uprights 'H2' to
Tarp Top Board 'M5', using screws
'BV', as shown.
Step 2: Attach Tarp Cross Braces
'G1' and 'G2' Tarp Cross Brace to
Tarp End Caps 'K1', using screws
'BV', as shown.
BV
M5
BV
H2
K1
H
BV
AC
H2
G2
D
AD
K
AC
BG
BV
Swing Beam Holes.
K1
G1
BV
Step 3: Attach Tarp Upright 'H2' to
Tarp Cross Brace 'G2', using
hardware 'H', 'AC', 'AD', & 'D', as
shown.
Step 4: Attach Tarp Upright 'H2' to
Tarp Cross Brace 'G1', using
hardware 'J', 'AC', & 'BG', as shown.
Fort Assembly
Phase 7
Parts needed:
Hardware needed:
• (1) TARP SUPPORT ASSEMBLY
• (4) D - NUT BARREL WH 5/16x7/8 - H100005
• (4) AD - WASHER LOCK EXT 12x19 - H100031
• (4) AC - WASHER LOCK EXT 8x19 - H100030
• (4) K - BOLT WH 5/16x2 - H100012
Phase Notes
• Assemble with hardware as shown.
Note: It is vital that the fort
be level before and after
each phase of assembly.
G2
E2
E1
AD
G1
K
K
D
D
AC
AD
AC
Left Side
Step 1: Attach Tarp Support
Assembly to 'E1' & 'E2' fort uprights
using hardware 'K', 'AC', 'AD' & 'D', as
shown.
Right Side
Step 2: Attach tarp support assembly
to 'E1' & 'E2' fort uprights using
hardware 'K', 'AC', 'AD' & 'D', as
shown.
Fort Assembly
Phase 8
Parts needed:
Hardware needed:
• (1) NL - ROOF TARP - A100258
• (9) CY - SCREW PWH 8x5/8 - H100128
Phase Notes
• Assemble with hardware as shown.
Note: It is vital that the fort
be level before and after
each phase of assembly.
CY
Step 1: Attach one end of 'NL' Tarp Green
to the inside of tarp end cap 'K1' with
Screws 'CY', as shown.
NL
M5
Step 2: Pull 'NL' Tarp Green to the inside
of tarp end cap 'K1' , on the opposite side,
and secure with Screws 'CY', as shown.
K1
K1
CY
Step 3: Secure 'NL' Tarp Green to
tarp top board 'M5' with Screws 'CY',
as shown.
Fort Assembly
Phase 9
Parts needed:
Hardware needed:
• (6) M3 - WALL SLAT - W101850
• (2) H4 - WALL RAIL - W101849
• (8) CK - SCREW PFH 8x2 - H100111
• (24) BP - SCREW PFH 8x1-1/2 - H100086
Phase Notes
• Assemble with hardware as shown.
q
Step 1: Attach 'H4' Wall Rails to the
outside of fort uprights 'E1' & 'E2' with
Screws 'CK', as shown.
E1
H4
CK
H4
E2
M3
H1
M3
E2
BP
H1
Step 2: Attach 'M3' Wall Slats to the inside
of 'H1' & 'H4' wall rails using screws 'BP',
as shown.
Swing Beam Attachment
Phase 10
Hardware needed:
Parts needed:
• (4) BG - T-NUT 5/16 - H100074
• (4) BX - WASHER SPLIT 5/16 - H100095
• (4) CD - WASHER FLAT 8x27 - H100105
• (4) AJ - BOLT HEX 5/16x1-1/4 - H100042
• (4) CY - SCREW PFH 8x5/8 - H100128
• (1) SWING BEAM ASSEMBLY
• (1) HC - BACKYARD DISCOVERY ID TAG - A100164
Phase Notes
• Assemble with hardware as shown.
CD
Note: It is vital that the fort
be level before and after
each phase of assembly.
BX
BG
AJ
HC
BX
G1
CD
CY
Step 2: Attach Backyard Discovery ID
Tag 'HC' to Swing Beam 'SB70' using
Screws 'CY', as shown.
Step 1: Attach the Swing Beam
Assembly to 'G1' Tarp Swing Cross
Beam using Bolts 'AJ', Washer 'BX' &
Washer 'CD' through the angle
brackets & 'G1' cross beam and into
T-Nut 'BG' that will need to be
hammered in the holes on the
backside of 'G1', as shown.
Slide Attachment
Phase 11
Parts needed:
• (1) SLIDE ASSEMBLY
Hardware needed:
• (3) B - NUT BARREL WH 5/16x5/8 - H100004
• (3) AD - WASHER LOCK EXT 12x19 - H100031
• (3) CM - BOLT WH 5/16x1/2 - H100115
Phase Notes
• Assemble with hardware as shown.
To prevent board splitting, you
must pre-drill each board with
a 1/8" drill bit, before attaching.
SLIDE ASSEMBLY
SLIDE ASSEMBLY
CM
Step 1: Center the wave slide
assembly in the opening opposite the
swing beam assembly, as shown.
Step 2: Using a drill with a 3/8" bit,
drill a hole through the holes on the
slide and through the fort floor.
Step 3: Attach the Slide Assembly to
the fort floor using the Safe-T-Fuse
hardware, as shown.
Anchoring Instructions
Phase 12
Parts needed:
Hardware needed:
• (6) KD - GROUND STAKE BROWN - A100179
• (2) DP - SWING SEAT GREEN - A100027
• (4) EZ - CHAIN GREEN 51.25" - A100068
• (4) FA - QUICK LINK - A100069
• (2) KN - CHAIN GREEN 31" - A100177
• (1) KF - TRAPEZE W/ HARDWARE YELLOW - A100109
• (6) CK - SCREW PFH 8x2 - H100111
*Stakes should be placed in concrete*
Phase Notes
• Assemble with hardware as shown.
• Install the screw into the upright so that the
tip of the screw does not stick through. Make
sure you have enough wood to accommodate
the screw before installing.
• FAILURE TO USE STAKES CAN VOID
WARRANTY & CAUSE INJURY!
STAKE
STAKE
SWING
Step 2: Attach Swing Seats 'DP' to
swing beam using Quick Clip 'FA' and
Chain 'EZ'.
TRAPEZE
Step 3: Attach trapeze assembly to
swing beam using Quick Clip 'FA' and
Chain 'KN'.
SWING
TIGHTEN QUICK
LINK
STAKE
STAKE
STAKE
STAKE
INSERT CHAIN INTO
QUICK LINK
KD
H80
CK
Install 2" screw into
both, the ground board
and the upright.
Step 1: Drive Stakes 'KD' into the ground
against boards where shown and attach
with Screws 'CK', as shown.
Final Step: Double check and make sure
every bolt, screw and nut is tight. Make
sure every board is secure. Make sure
the fort is level and enjoy your swing set.
Limited Warranty
This Limited Warranty by Backyard Discovery applies to products manufactured under the Backyard Discovery
brand or its other brands including but not limited to Backyard Botanical, Adventure Playsets, and Leisure Time
Products.
Backyard Discovery warrants that this product is free from defect in materials and workmanship for a period of
one (1) year from the original date of purchase. This one (1) year warranty covers all parts including wood,
hardware, and accessories. All wood carries a five (5) year pro-rated warranty against rot and decay. Refer to
the schedule below for charges associated with replacement of parts under this Limited Warranty. In addition,
Backyard Discovery will replace any parts within the first 30 days from date of purchase found to be missing
from or damaged in the original packaging.
This warranty applies to the original owner and registrant and is non-transferable. Regular maintenance is
required to assure maximum life and performance of this product and failure by the owner to maintain the
product according to the maintenance requirements may void this warranty. Maintenance guidelines are
provided in the Owner’s Manual.
This Limited Warranty does not cover:








Labor for any inspection
Labor for replacement of any defective item(s)
Incidental or consequential damages
Cosmetic defects which do not affect performance or integrity of a part or the entire product
Vandalism, improper use, failure due to loading or use beyond the capacities stated in the applicable
Assembly Manual.
Acts of nature including but not limited to wind, storms, hail, floods, excessive water exposure
Improper installation including but not limited to installation on uneven, unlevel, or soft ground
Minor twisting, warping, checking, or any other natural occurring properties of wood that do not affect
performance or integrity
Backyard Discovery products have been designed for safety and quality. Any modifications made to the
original product could damage the structural integrity of the unit leading to failure and possible injury.
Modification voids any and all warranties and Backyard Discovery assumes no liability for any modified
products or consequences resulting from failure of a modified product.
This product is warranted for RESIDENTIAL USE ONLY. Under no circumstance should a Backyard Discovery
product be used in public settings. Such use may lead to product failure and potential injury. Any and all public
use will void this warranty. Backyard Discovery disclaims all other representations and warranties of any kind,
express or implied.
This Warranty gives you specific legal rights. You may have other rights as well which vary from state to state
or province to province. This warranty excludes all consequential damages, however, some states do not allow
the limitation or exclusion of consequential damages and therefore this limitation may not apply to you.
Pro Rated Part Replacement Schedule
Product Age
All Parts
0-30 days from date of purchase
31 days to 1 year
Customer Pays
$0 and free shipping
$0 + S&H
Wood Rot and Decay Only
1 year
2 years
3 years
4 years
5 years
Over 5 years
$0 and free shipping
20% + S&H
40% + S&H
60% + S&H
80% + S&H
100% + S&H
Rev5/20/10 BRS
">