GE-300-SX-LASER Motion Controller

GE-300-SX-LASER Motion Controller
Googol Technology
GE-300-SX-laser 0406
GE-300-SX-LASER Motion Controller
The
GE-300-SX-Laser
series
motion
controllers
contain -SG and –SV models which are developed base
on Googol’s economic model GE-300-SG motion
controller. The main feature of this series motion
controllers are the consideration of the synchronization
and coordination between the motor motion and the
laser system, supplying of specific signal for several sorts of laser system, such as CO2 laser, or
YAG laser (equipped with terminal board named GA1-400-ACC2-OYAG). This series are
suitable for many industrial application related with laser processing, such as Laser cutting, Laser
engraving, Laser drilling, rapid prototype typing, and Laser joining, etc.
Technical specifications
1) Motion Control Functions
•
Synchronized motion of 3 axes, linear and circular interpolation;
•
Pulse output of 3 axes, programmable output modes, maximum pulse output frequency
256KHz;
•
Support buffer motion and immediate motion;
•
Motion start, pause, stop, and restore;
•
Auto emergent stop motion when motion touched the limit signal;
•
High precision of interpolation, the precision of circular interpolation is under the 0.5
pulse;
•
On-board, circular memory buffer for fast communication and look ahead function;
•
Continuous and smooth motion for minute multi-segments path;
•
Support the management of coordinate system offset;
•
Supply the delay between two segment motion, unit: 200us;
•
Allow user to change the feed speed of the motion on the fly by changing the override;
•
Support the management of general IO during buffer motion.
2) Laser Control Functions:
•
Provide several sorts of signal to control two sorts of laser:
1.
signals for CO2 laser:
LASER ON signal, TTL standard;
PWM signal, or frequency signal, or Analog voltage signal (only in GE-300-SVLASER motion controller), selected by user command
-1-
Googol Technology
2.
GE-300-SX-laser 0406
signals for YAG laser (must use terminal board named GA1-400-ACC2-OYAG )
LASER ON signal, TTL standard;
Q pulse signal, the duty and frequency can be programmable;
FPK signal (First Pulse Killer)
•
Provide laser on and off signal delay function, unit: 1µs.
•
Motion delay also can be used between two laser on/off signal;
•
Three energy control of laser output methods provided
i.
Energy follow up mode: output of laser energy control varies according to the
motion speed changes
ii.
Interval direct output mode: magnitude of laser energy output is changed in
different trajectory segment intervals, users can directly control the energy of the
laser between path segments
iii.
Scan mode: with this mode, laser energy and laser on/off can be set for each point
in a line. Controlling motors to work line by line can scan an image such as bmp.
The function is accomplished by hardware with high speed.
Note: Energy output mode should be set to duty output mode when location comparison
output control mode is used
•
Provide different laser power control output mode: duty ratio, frequency or voltage (only
in GE-300-SV-LASER )
i.
The range of output frequency: 200HZ~55KHZ, the default value is 200HZ;
ii.
The range of duty ratio: 0%~100%, minimum variance: 1%, system default: 50%;
iii.
If the laser power control output mode is frequency, the minimum variance is
200HZ
•
When operating in buffer continuous trajectory motion, laser energy offset can be altered
on line at anytime via commands
3) Input and Output Signal:
•
2 channel of limit input signals, 1 channel of home input signal and 1 channel of driver
alarm input signal for each axis, all of them are opto-isolated;
•
1 channel of axis on output signal, 1 channel of driver reset output signal for each axis,
all of them are opto-isolated;
•
three channel of axis encoder input signals, with index captured function;
•
16 bit general purposed IO, These can be operated in buffer or instantaneous modes
4) Interface:
•
Support standard PCI, ISA and PC104;
•
Application mode:
GE-300-SX-LASER-PCI/ISA + PC
GU-300-SX-LASER-XXX/XXX (embedded motion controller)
-2-
Googol Technology
GE-300-SX-laser 0406
5) System Software:
Driver program and DLL for Windows 98/2000/NT, library of C language for DOS;
DEMO in Windows 98/2000/NT;
The motion controller with PCI bus must be installed according to the guidance specified
in user manual before being used, the motion controller with ISA bus must be installed
when working under the Windows system.
Selection Guide
Model
Motor control
Laser power control
GE-300-SG-Laser-G
Pulse output
Duty ratio or frequency
GE-300-SV-Laser-G
Pulse output
Duty ratio, or frequency, or
analog voltage output
Ordering Information
Model No.
Standard
Package
Option
Description
GE-300-SG-LASER-PCI/ISA;
Motion control card with 3 axes motion
or
control and 1 channel laser energy control
GE-300-SV-LASER-PCI/ISA
ACC1 and ACC4
Connector with a 60-pin flat cable
ACC3-A1-062015
1.5m 62-pin cable (×2)
GA1-300-ACC2-G
Terminal board
Control Software
Control software for Windows
98/2000/NT, extended DLL;
function library, etc.
GA1-400- ACC2-OYAG
Terminal board special for YAG
laser resource
ACC3-A1-062030
3.0 m 62-pin cable
Enquiry and Feedback:
Googol Technology (HK) Limited
Tel: +852 2358 1033; +852 2719 8310 Fax: +852 27198399;
Email: sales@googoltech.com:
WebPages: http://www.googoltech.com
-3-
Qty
1
1
2
1
1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising