Panasonic WV-SF538E surveillance camera

Panasonic WV-SF538E surveillance camera
Installation Guide
Network Camera
WV-SF549/WV-SF548
WV-SF539/WV-SF538
WV-SF549E/WV-SF548E
WV-SF539E/WV-SF538E
Model No.
WV-SF549
WV-SF539
Before attempting to connect or operate this product, please read these
instructions carefully and save this manual for future use.
The model number is abbreviated in some descriptions in this manual.
For U.S.A
WARNING:
• To prevent injury, this apparatus must be
securely attached to the floor/wall/ceiling in
accordance with the installation instructions.
• To prevent fire or electric shock hazard, do not
expose this apparatus to rain or moisture.
• The installation shall be carried out in accordance with all applicable installation rules.
• The connections should comply with local
electrical code.
For U.S. and Canada:
WV-SF549, WV-SF548, WV-SF539, WV-SF538
For Europe and other countries:
WV-SF549E, WV-SF548E, WV-SF539E,
WV-SF538E
UL listed model No.
WV-SF549, WV-SF548, WV-SF539, WV-SF538
For Canada
This Class A digital apparatus complies with
Canadian ICES-003.
For U.S.A
NOTE: This equipment has been tested and
found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area
is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
FCC Caution: To assure continued compliance,
(example - use only shielded interface cables
when connecting to computer or peripheral
devices). Any changes or modifications not
expressly approved by the party responsible for
compliance could void the user’s authority to
operate this equipment.
2
The model number and serial number of this
product may be found on the surface of the
unit.
You should note the model number and serial
number of this unit in the space provided and
retain this book as a permanent record of your
purchase to aid identification in the event of
theft.
Model No.
Serial No.
For Europe
We declare under our sole responsibility that the product
to which this declaration relates is in conformity with the
standard or other normative document following the
provisions of Directive 2004/108/EC.
Wir erklären in alleiniger Verantwortung, daß das Produkt,
auf das sich diese Erklärung bezieht, mit der folgenden
Norm oder normativen Dokument übereinstimmt. Gemäß
den Bestimmungen der Richtlinie 2004/108/EC.
Nous déclarons sous notre propre responsabilité que le
produit auquel se réfère la présente déclaration est
conforme á la norme spécifiée ou à tout autre document
normatif conformément aux dispositions de la directive
2004/108/CE.
Nosotros declaramos bajo nuestra única responsabilidad
que el producto a que hace referencia esta declaración
está conforme con la norma u otro documento normativo
siguiendo las estipulaciones de la directiva 2004/108/CE.
Noi dichiariamo sotto nostra esclusiva responsabilità che
il prodotto a cui si riferisce la presente dichiarazione
risulta conforme al seguente standard o altro documento
normativo conforme alle disposizioni della direttiva
2004/108/CE.
Wij verklaren als enige aansprakelijke, dat het product
waarop deze verklaring betrekking heeft, voldoet aan de
volgende norm of ander normatief dokument,
overeenkomstig de bepalingen van Richtlijn 2004/108/
EC.
Vi erklærer os eneansvarlige for, at dette produkt, som
denne deklaration omhandler, er i overensstemmelse
med standard eller andre normative dokumenter i følge
bestemmelserne i direktiv 2004/108/EC.
Vi deklarerar härmed vårt fulla ansvar för att den produkt
till
vilken
denna
deklaration
hänvisar
är
i
överensstämmelse med standarddokument eller annat
normativt dokument som framställs i direktiv 2004/108/
EC.
Ilmoitamme yksinomaisella vastuullamme, että tuote, jota
tämä ilmoitus koskee, noudattaa seuraavaa standardia
tai muuta ohjeellista asiakirjaa, jotka noudattavat
direktiivin 2004/108/EC säädöksiä.
Vi erklærer oss alene ansvarlige for at produktet som
denne erklæringen gjelder for, er i overensstemmelse
med følgende norm eller andre normgivende dokumenter
som følger bestemmelsene i direktiv 2004/108/EC.
目目
Contents
Important safety instructions......................................................................................................... 4
Limitation of liability ....................................................................................................................... 5
Disclaimer of warranty ................................................................................................................... 5
Preface .......................................................................................................................................... 6
About notations ............................................................................................................................. 6
Main functions ............................................................................................................................... 6
About the user manuals ................................................................................................................ 7
System requirements for a PC ...................................................................................................... 7
Trademarks and registered trademarks......................................................................................... 8
Copyright ....................................................................................................................................... 8
Network security ........................................................................................................................... 9
Precautions ................................................................................................................................. 10
Precautions for Installation .......................................................................................................... 13
Major operating controls ............................................................................................................. 15
Detaching the dome cover .......................................................................................................... 17
Preparations ................................................................................................................................ 19
Insert/remove an SD memory card (WV-SF549/WV-SF539 only)* .............................................. 22
Connection .................................................................................................................................. 23
Installation ................................................................................................................................... 29
Adjustment .................................................................................................................................. 30
Attaching the dome cover ........................................................................................................... 34
Using the CD-ROM ..................................................................................................................... 37
Configure the network settings ................................................................................................... 40
Troubleshooting ........................................................................................................................... 42
Specifications .............................................................................................................................. 43
Standard accessories .................................................................................................................. 47
Optional accessories ................................................................................................................... 47
* SDXC/SDHC/SD memory card is described as SD memory card.
3
Important safety instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9) Only use attachments/accessories specified by the manufacturer.
10) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
S3125A
11) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
4
Limitation of liability
THIS PUBLICATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF
THE THIRD PARTY'S RIGHT.
THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICAL
ERRORS. CHANGES ARE ADDED TO THE INFORMATION HEREIN, AT ANY TIME, FOR THE
IMPROVEMENTS OF THIS PUBLICATION AND/OR THE CORRESPONDING PRODUCT (S).
Disclaimer of warranty
IN NO EVENT SHALL Panasonic System Networks Co., Ltd. BE LIABLE TO ANY PARTY OR ANY
PERSON, EXCEPT FOR REPLACEMENT OR REASONABLE MAINTENANCE OF THE PRODUCT,
FOR THE CASES, INCLUDING BUT NOT LIMITED TO BELOW:
(1) ANY DAMAGE AND LOSS, INCLUDING WITHOUT LIMITATION, DIRECT OR INDIRECT,
SPECIAL, CONSEQUENTIAL OR EXEMPLARY, ARISING OUT OF OR RELATING TO THE
PRODUCT;
(2) PERSONAL INJURY OR ANY DAMAGE CAUSED BY INAPPROPRIATE USE OR NEGLIGENT
OPERATION OF THE USER;
(3) ALL MALFUNCTIONS OR TROUBLES FROM UNAUTHORIZED DISASSEMBLE, REPAIR OR
MODIFICATION OF THE PRODUCT BY THE USER, REGARDLESS OF THE CAUSE OF THE
MALFUNCTION OR TROUBLE;
(4) INCONVENIENCE OR ANY LOSS ARISING WHEN IMAGES ARE NOT DISPLAYED, DUE TO
ANY REASON OR CAUSE INCLUDING ANY FAILURE OR PROBLEM OF THE PRODUCT;
(5) ANY PROBLEM, CONSEQUENTIAL INCONVENIENCE, OR LOSS OR DAMAGE, ARISING
OUT OF THE SYSTEM COMBINED BY THE DEVICES OF THIRD PARTY;
(6) ANY CLAIM OR ACTION FOR DAMAGES, BROUGHT BY ANY PERSON OR ORGANIZATION
BEING A PHOTOGENIC SUBJECT, DUE TO VIOLATION OF PRIVACY WITH THE RESULT OF
THAT SURVEILLANCE-CAMERA'S PICTURE, INCLUDING SAVED DATA, FOR SOME
REASON, BECOMES PUBLIC OR IS USED FOR ANY PURPOSE;
(7) LOSS OF REGISTERED DATA CAUSED BY ANY FAILURE.
5
Preface
The network cameras WV-SF549/WV-SF548/WV-SF539/WV-SF538/WV-SF549E/WV-SF548E/
WV-SF539E/WV-SF538E are designed to operate using a PC on a network (10BASE-T/100BASETX).
By connecting to a network (LAN) or the Internet, images and audio from the camera can be monitored on a PC via a network.
Note:
• It is necessary to configure the network settings of the PC and its network environment to monitor images from the camera on the PC. It is also necessary to install a web browser on the PC.
About notations
The following notations are used when describing the functions limited for specified models.
The functions without the notations are supported by all models.
SF549
:The functions with this notation are available when using the model WV-SF549.
SF548
:The functions with this notation are available when using the model WV-SF548.
SF539
:The functions with this notation are available when using the model WV-SF539.
SF538
:The functions with this notation are available when using the model WV-SF538.
Main functions
H.264 and JPEG triple encoding
H.264 dual stream output and JPEG output can be simultaneously provided.
* H.264 stream1: 1920x1080/ max. 30 fps
H.264 stream2: 640x360/ max. 30 fps
Cropping function (the function of cutting out the image capture area)
At the same time as providing the whole image, it is possible to provide the part cut out from whole
image. Up to 4 image capture areas can be specified, and it is also possible to control the sequence.
* It is possible to control its sequence and transmit the image cut out only when H.264 stream2 is provided.
VIQS function (Variable Image Quality on Specified area)
It is possible to provide specified areas with high quality image without changing the overall size of
the data. Up to 2 areas can be specified.
SF539
SDXC/SDHC/SD memory card slot equipped SF549
It is possible to save H.264 videos and JPEG images on the SDXC/SDHC/SD memory card manually at an alarm occurrence, during the period of the schedule, or on a web browser. It is also possible to save JPEG images at a network failure occurrence. (Download is possible.)
(Recommended SDXC/SDHC/SD memory card ☞ page 46)
Super Dynamic
(☞ Operating Instructions (included in the CD-ROM))
Super Dynamic compensates brightness on a pixel-to-pixel basis so that it produces clearer images
even if objects have various illumination intensities.
Auto focus (AF) function
It is possible to adjust the focus automatically by moving the focus ring of the lens with the operation button of this camera or the setup menu.
6
About the user manuals
There are 2 sets of operating instructions for the WV-SF549, WV-SF548, WV-SF539, WV-SF538
(P model), WV-SF549E, WV-SF548E, WV-SF539E, WV-SF538E (E model) as follows.
• InstallationGuide:Explainshowtoinstallandconnectdevices.
• Operating Instructions (included in the CD-ROM): Explains how to perform the settings and
how to operate this camera.
Adobe® Reader® is required to read these operating instructions on the provided CD-ROM.
When the Adobe Reader is not installed on the PC, download the latest Adobe Reader from the
Adobe web site and install it.
"WV-SF549, WV-SF548, WV-SF539, WV-SF538" or "SF549, SF548, SF539, SF538" shown in the
instructions and illustrations used in these operating instructions indicates the WV-SF549,
WV-SF548, WV-SF539, WV-SF538, WV-SF549E, WV-SF548E, WV-SF539E, WV-SF538E.
The screens used in these operating instructions show the cases of P models.
System requirements for a PC
CPU:
Memory:
Network Interface:
Audio Interface:
Monitor:
OS:
Web browser:
Others:
Intel® CoreTM 2 Duo 2.4 GHz or faster recommended
512 MB or more (A minimum of 1 GB memory is required when using
Microsoft® Windows® 7 or Microsoft® Windows Vista®.)
10BASE-T/100BASE-TX 1 port
Sound card (when using the audio function)
Image capture size: 1024 x 768 pixels or more
Color: 24-bit True color or better
Microsoft® Windows® 7
Microsoft® Windows Vista®
Microsoft® Windows® XP SP3
Windows® Internet Explorer® 9.0 (32-bit)
Windows® Internet Explorer® 8.0 (32-bit)
Windows® Internet Explorer® 7.0 (32-bit)
Microsoft® Internet Explorer® 6.0 SP3
CD-ROM drive
(It is necessary to read the operating instructions and use the software on
the provided CD-ROM.)
DirectX® 9.0c or later
Adobe® Reader®
(It is necessary to view the PDF file on the provided CD-ROM.)
IMPORTANT:
• When using a PC that does not meet the above requirements, displaying of images may
become slower or the web browser may become inoperable.
• Audio may not be heard if a sound card is not installed on a PC. Audio may be interrupted
depending on the network environment.
• Microsoft Windows 7 Starter, Microsoft Windows Vista Starter and Microsoft Windows XP
Professional 64-bit Edition are not supported.
• WhenusingIPv6forcommunication,useMicrosoftWindows7orMicrosoftWindowsVista.
7
Note:
• For further information about PC system requirements and precautions for when using
Microsoft Windows 7, Microsoft Windows Vista, or Windows Internet Explorer, click "Manual" "Open" from the supplied CD-ROM and refer to "Notes on Windows® / Internet Explorer®
versions".
• IfusingMicrosoftWindowsXP,screentearing*mayoccurwhentheshootingscenedrastically
changes (for example, while shooting fast-moving subjects) due to the GDI restrictions of the
OS.
* A phenomenon in which portions of the screen are displayed out of alignment
• For information on the operation verification of the supported operating systems and web
browsers, refer to our website at http://panasonic.net/pss/security/support/index.html.
Trademarks and registered trademarks
• Adobe, Acrobat Reader, and Reader are either registered trademarks or trademarks of Adobe
Systems Incorporated in the United States and/or other countries.
• Microsoft, Windows, Windows Vista, Internet Explorer, ActiveX, and DirectX are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other
countries.
• Microsoftproductscreenshot(s)reprintedwithpermissionfromMicrosoftCorporation.
• IntelandIntelCorearetrademarksorregisteredtrademarksofIntelCorporationoritssubsidiaries in the United States and other countries.
• SDXCLogoisatrademarkofSD-3C,LLC.
• iPad, iPhone, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other
countries.
• AndroidisatrademarkofGoogleInc.UseofthistrademarkissubjecttoGooglePermissions.
• Allothertrademarksidentifiedhereinarethepropertyoftheirrespectiveowners.
Copyright
Distributing, copying, disassembling, reverse compiling and reverse engineering of the software
provided with this product are all expressly prohibited. In addition, exporting any software provided
with this product violating export laws is prohibited.
8
Network security
As you will use this unit connected to a network, your attention is called to the following security
risks.
q Leakage or theft of information through this unit
w Use of this unit for illegal operations by persons with malicious intent
e Interference with or stoppage of this unit by persons with malicious intent
It is your responsibility to take precautions such as those described below to protect yourself
against the above network security risks.
• Usethisunitinanetworksecuredbyafirewall,etc.
• IfthisunitisconnectedtoanetworkthatincludesPCs,makesurethatthesystemisnotinfected by computer viruses or other malicious entities (using a regularly updated anti-virus program, anti-spyware program, etc.).
• Protectyournetworkagainstunauthorizedaccessbyrestrictinguserstothosewhologinwith
an authorized user name and password.
• Applymeasuressuchasuserauthenticationtoprotectyournetworkagainstleakageortheftof
information, including image data, authentication information (user names and passwords),
alarm E-mail information, FTP server information and DDNS server information.
• Aftertheunitisaccessedbytheadministrator,makesuretoclosethebrowser.
• Changetheadministratorpasswordperiodically.
• Do not install the camera in locations where the camera or the cables can be destroyed or
damaged by persons with malicious intent.
9
Precautions
Refer installation work to the dealer.
Installation work requires technique and experiences. Failure to observe this may cause fire,
electric shock, injury, or damage to the product.
Be sure to consult the dealer.
Stop the operation immediately when
something is wrong with this product.
When smoke goes up from the product, the
smell of smoke comes from the product, or the
exterior of the product has deteriorated, continued use will cause a fire or fall of the product
resulting in injury, accidents, or damage to the
product.
Turn the power off immediately and contact
qualified service personnel for service.
Do not attempt to disassemble or modify
this product.
Failure to observe this may cause fire or electric shock.
Consult the dealer for the repair or inspections.
Do not insert any foreign objects.
This could permanently damage this product.
Turn the power off immediately and contact
qualified service personnel for service.
Select an installation area that can support the total weight.
Selecting an inappropriate installation surface
may cause the product to fall down or topple
over, resulting in injury.
Installation work shall be started after sufficient
reinforcement.
Periodic inspections shall be conducted.
Rust on the metal parts or screws may cause a
fall of the product resulting in injury or accidents.
Consult the dealer for the inspections.
Do not use this product in an inflammable
atmosphere.
Failure to observe this may cause an explosion
resulting in injury.
Avoid installing this product in the locations where salt damage occurs or corrosive gas is produced.
Otherwise, the mounting portions will deteriorate and
accidents such as a fall of this product may occur.
The exclusively designed mount bracket
shall be used.
Failure to observe this may cause a drop resulting in injury or accidents.
Use the exclusively designed mount bracket for
installation.
10
The screws and bolts must be tightened to
the specified torque.
Failure to observe this may cause a drop resulting in injury or accidents.
Do not install this product in locations
subject to vibration.
Loosening of mounting screws or bolts may
cause a fall of the product resulting in injury.
Install this product in a location high
enough to avoid people and objects from
bumping the product.
Failure to observe this may cause a drop resulting in injury or accidents.
Do not strike or give a strong shock to this
product.
Failure to observe this may cause fire or injury.
Turn the power off when wiring this product.
Failure to observe this may cause electric shock. In
addition, short circuit or wrong wiring may cause fire.
Do not rub the edges of metal parts with
your hand.
Failure to observe this may cause injury.
Do not touch this product, the power cord
or the connected cables during thunder.
(even in the process of work)
Failure to observe this may cause electric shock.
Keep SDXC/SDHC/SD memory cards
(option) away from infants and children.
Otherwise, they may swallow the cards by mistake.
In this case, consult a doctor immediately.
Do not damage the power cable.
Do not damage, fabricate, twist, stretch, bundle, or forcibly bend the power cable. Do not
place heavy objects.
Keep away from heat sources.
Use of the damaged power cable may cause
electric shock, short circuit, or fire.
Consult the dealer for repair.
Turn the power off when cleaning of this
product.
Failure to observe this may cause injury.
[Precautions for use]
This product is designed to be used indoors.
This product is not operable outdoors.
This product has no power switch.
When turning off the power, disconnect the
power supply from the 12 V DC power supply
or the PoE device. (When using both the 12 V
DC power supply and the PoE device for power
supply, disconnect both the connections.)
To keep on using with stable performance
Do not use this camera in hot and humid conditions for a long time.
Failure to observe this causes component degradation resulting in life shortening of this product.
Do not expose this product to direct heat
sources such as a heater.
Do not touch the dome cover with your
bare hands.
A dirty dome cover causes deterioration of picture quality.
Handle this camera with care.
Do not drop this product, nor apply shock or
vibration to the product. Failure to observe this
may cause trouble. If a strong shock or vibration is applied to the dome cover, it may cause
damage.
About the PC monitor
Displaying the same image on a monitor for a
long time may damage the monitor. It is recommended to use a screen-saver.
When an error is detected, this product
will restart automatically.
This product will be inoperable for around
2 minutes after the restart just as when the
power is turned on.
Product disposal/transfer
Data saved on this product or a storage device
used with this product may lead to personal
information leakage. When it is necessary to
dispose or give this product to someone, even
when for repair, make sure that there is no data
on this product.
Cleaning this product body
Be sure to turn off the power before cleaning.
Failure to observe this may cause injury. Do not
use strong abrasive detergent when cleaning this
product. Otherwise, it may cause discoloration.
When using a chemical cloth for cleaning, read
the caution provided with the chemical cloth
product.
Cleaning the lens
Use a lens cleaning paper (used to clean camera lenses or lenses of spectacles). When using
solvent, use an alcohols solvent and do not use
a thinner or a glass cleaner.
Transmission interval
Image transmission interval may become slow
depending on the network environment, PC
performance, shooting subject, access number, etc.
About SD memory card
• Before inserting the SD memory card, turn
off the power of this product first.
Otherwise, it may cause malfunction or
damage data recorded on the SD memory
card. Refer to page 22 for descriptions of
how to insert/remove an SD memory card.
• When using a SD memory card, format it
using this product. Recorded data on the
SD memory card will be deleted when formatted. If an unformatted SD memory card
or a SD memory card formatted with other
devices is used, this product may not work
properly or performance deterioration may
be caused. Refer to the Operating
Instructions (included in the CD-ROM) for
how to format a SD memory card.
• When some SD memory cards are used
with this product, the product may not
work properly or performance deterioration
may be caused.
Code label
The code labels (accessory) are required at
inquiry for trouble. Use caution not to lose
these labels. It is recommended to paste one
of the labels onto the CD-ROM case.
11
Discoloration on the color filter of the
MOS image sensor
• When continuously shooting a bright light
source such as a spotlight, the color filter
of the MOS image sensor may have deteriorated and it may cause discoloration.
Even when changing the fixed shooting
direction after continuously shooting a
spotlight for a certain period, the discoloration may remain.
• When shooting fast-moving subjects or
performing
panning/tilting
operations,
objects crossing the shooting area may
look to be bending askew.
AVC Patent Portfolio License
THIS PRODUCT IS LICENSED UNDER THE
AVC PATENT PORTFOLIO LICENSE FOR THE
PERSONAL USE OF A CONSUMER OR
OTHER USES IN WHICH IT DOES NOT
RECEIVE REMUNERATION TO (i) ENCODE
VIDEO IN COMPLIANCE WITH THE AVC
STANDARD ("AVC VIDEO") AND/OR (ii)
DECODE AVC VIDEO THAT WAS ENCODED
BY A CONSUMER ENGAGED IN A
PERSONAL ACTIVITY AND/OR WAS
OBTAINED FROM A VIDEO PROVIDER
LICENSED TO PROVIDE AVC VIDEO. NO
LICENSE IS GRANTED OR SHALL BE
IMPLIED FOR ANY OTHER USE. ADDITIONAL
INFORMATION MAY BE OBTAINED FROM
MPEG LA, L.L.C.
SEE HTTP://WWW.MPEGLA.COM
12
Precautions for Installation
Panasonic assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation.
This camera is designed to be used indoors.
This product is not operable outdoors.
Do not expose this camera to direct sunlight for
hours and do not install the product near a heater
or an air conditioner. Otherwise, it may cause
deformation, discoloration and malfunction. Keep
this camera away from water and moisture.
Installing place
Contact your dealer for assistance if you are
unsure of an appropriate place in your particular environment.
• Make sure that the installation area is
strong enough to hold this product, such
as a concrete ceiling.
• Installthecamerainthefoundationareaof
the architecture or where sufficient strength
is assured.
• If a ceiling board such as plaster board is
too weak to support the total weight, the
area shall be sufficiently reinforced.
Do not place this product in the following
places:
• Locations where it may get wet from rain
or water splash
• Locationswhereachemicalagentisused
such as a swimming pool
• Locationssubjecttomoistureoroilsmoke
such as a kitchen
• Locationsthathaveaspecificenvironment
that is subject to an inflammable atmosphere or solvents
• Locations where a radiation, an X-ray, a
strong radio wave or a strong magnetic
field is generated
• Locations where corrosive gas is produced, Locations where it may be damaged by briny air such as seashores
• Locations where the temperature is not
within the specified range (page 43).
• Locationssubjecttovibrations(Thisproduct is not designed for on-vehicle use.)
• Locations subject to condensation as the
result of severe changes in temperature
(In case of installing the camera in such locations, the dome cover may become foggy or
condensation may be caused on the cover.)
Be sure to remove this product if it is not
in use.
Shielded (STP) LAN cables must be used
with this unit to ensure compliance with
EMC standards. *
* E models only
Before installation
• The camera mount bracket described on
page 19 shall be used to mount the camera.
• When this camera and camera mount
bracket are mounted on a ceiling or a wall,
use the screws described on page 19. The
screws to be used are not provided.
Prepare the screws according to the material, structure, strength and other factors of
the mounting area and the total weight of
objects to be mounted.
• Ensure that the mounting surface, anchor
and screws are sufficiently strong.
• Do not mount this product on a plaster
board or a wooden section because they
are too weak. If this product is unavoidably
mounted on such a section, the section
shall be sufficiently reinforced or use an
optional ceiling mount bracket (WV-Q105).
About the network connection
When connecting to a network using the network cable of this product, observe the following.
• When wiring for the network, design and
engineer not to be affected by thunder.
13
Screw tightening
• The screws and bolts must be tightened
with an appropriate tightening torque
according to the material and strength of
the installation area.
• Do not use an impact driver. Use of an
impact driver may damage the screws or
cause tightening excessively.
• Tighten screws at a right angle to the surface. After tightening screws, perform checks
to ensure that the tightening is sufficient
enough so that there is no movement or
looseness.
Procure fixing screws separately.
The screws that secure this product are not
supplied. Prepare them according to the material and strength of the area where the product
is to be installed.
Radio disturbance
When this product is used near TV/radio antenna, strong electric field or magnetic field (near a
motor, a transformer or a power line), images
may be distorted and noise sound may be produced.
PoE (Power over Ethernet)
Use a PoE hub/device that is compliant with
IEEE802.3af standard.
Router
When connecting this product to the Internet,
use a broadband router with the port forwarding function (NAT, IP masquerade).
Refer to the Operating Instructions (included in
the CD-ROM) for further information about the
port forwarding function.
Time & date setting
It is necessary to set the time & date before
putting this product into operation. Refer to the
Operating Instructions on the provided
CD-ROM for descriptions of how to perform
the settings.
14
Major operating controls
SF549
SF548
Dome cover
SF539
SF538
Inner dome
Inner dome
Clear dome
(Provided only for service)
Monitor out connector for
service*
SF539
SF538
Marker
SF549
SF548
Dome cover fixing screw hole
Direction marker for installation
SF539
SF538
Dome cover fixing projection
Azimuth adjustment ring
Monitor out connector
for adjustment
(RCA jack)
View from the side
Tilting table
Panning lock screw [LOCK]
12 V DC power supply
terminal
Panning table
Direction marker for installation
SF549
SF548
Dome cover fixing screw hole
SF549
SF548
Support wire for installation
* This connector is provided only for service. Do not use the connector for checking the adjustment of the angular field of view on the video monitor.
IMPORTANT:
• Donotholdtheinnerdomewhileworkingonthecamera.Theinnerdomemaycomeoffofthe
camera. SF549
SF548
15
<Side view>
SD memory card slot
SF549
SF539
Access indicator (blinking at accessing)
Link indicator (lighting at linking)
Auto focus (AF) button/
Upside-down button
SF548
SF538
Auto focus (AF) button/
Upside-down button
INITIAL SET button
AF
Tilting lock screw
SD memory card error indicator/
Auto focus indicator
(blinks when adjusting auto focus)
SF549
External I/O terminals
SF539
Audio output connector
SF549
Microphone/line input connector
SF539
SF549
SF539
Zoom lock knob
Network connector
Tilting lock screw
Focus ring
About the [INITIAL SET] button
After turning off the power of the camera, turn on the power of the camera while holding down this
button, and wait for around 5 seconds or more without releasing this button. Wait around 2 minutes
after releasing the button. The camera will start up and the settings including the network settings
will be initialized. Do not turn off the power of the camera during the process of initialization. Before
initializing the settings, it is recommended to write down the settings in advance.
16
Detaching the dome cover
Detach the dome cover from the camera by loosening the dome cover fixing screws.
SF549
SF548
The following procedure is required when using WV-SF549 or WV-SF548. Refer to page 18 when
using WV-SF539 or WV-SF538.
IMPORTANT:
• Removethecoverfilmfromthedomesectionofthedomecoveraftertheinstallationiscomplete. Do not touch the dome section by hand directly after removing the cover film.
z Loosen the dome cover fixing screws using
the bit for tamperproof screw (accessory).
Note:
• Thedomecoverandthecameraarejointed with an assist wire. Do not remove the
assist wire.
Dome cover fixing screw
17
Detach the dome cover from the camera by removing the dome cover fixing screw.
SF539
SF538
The following procedure is required when using WV-SF539 or WV-SF538. Refer to page 17 when
using WV-SF549 or WV-SF548.
IMPORTANT:
• Afterremoval,retainthedomecoverfixingscrewsoasnottolose.Thescrewisrequiredwhen
attaching the dome cover. (☞ Page 34)
• Removethecoverfilmfromthedomesectionofthedomecoveraftertheinstallationiscomplete. Do not touch the dome section by hand directly after removing the cover film.
z Remove the dome cover fixing screw (M3,
AF
LOCK OPEN
ADJUST
step screw, x1).
Dome cover fixing screw
(M3, step screw)
x Rotate
the dome cover counterclockwise
two steps, and align the indication "OPEN"
to the marker of the camera to detach the
dome cover.
Note:
• Before the camera is installed, the dome
cover can be removed more easily when
putting a finger over the opening on the
bottom of the camera.
Marker
Dome alignment
indication
"OPEN"
LOCK
AF
Dome
cover
AF
OPEN
LOCK
ADJUST
Dome section
18
OPEN
ADJUST
Preparations
When installing the camera on a wall or a ceiling, there are four methods as specified below.
(☞ Pages 20 and 21)
• Usingthetwo-gangjunctionbox
• Installingthecameradirectlyontheceilingorwall
• Using the optional ceiling mount bracket WV-Q174 (for embedded installation on a ceiling)
SF539
SF538
• UsingtheoptionalceilingmountbracketWV-Q105*1 (for direct mounting on a ceiling)
IMPORTANT:
• Procure4screws(M4)tosecurethecameratoawalloraceilingaccordingtothematerialof
the installation area. In this case, wood screws and nails should not be used. For mounting a
camera on a concrete wall, use an anchor bolt (for M4) or an AY plug bolt (M4) for securing.
(Recommended tightening torque: 1.6 N·m {1.18 lbf·ft})
• Requiredpull-outcapacityofasinglescrew/boltis196N{44lbf}ormore.
• Ifaceilingboardsuchasplasterboardistooweaktosupportthetotalweight,theareashall
be sufficiently reinforced or the optional ceiling mount bracket for the camera, WV-Q105, must
be used.
The mounting conditions of the camera are described as follows:
Installation place
Applicable
mount bracket
Ceiling/wall
Number of
screw
Minimum pull-out
strength (per 1 pc.)
Two-gang junction M4
box
4 pcs.
196 N {44 lbf}
(Direct mounting) M4
4 pcs.
196 N {44 lbf}
Ceiling
WV-Q174
(approx. 280 g
{0.8 lbs})
–
–
*2
Ceiling
WV-Q105*1
(approx. 150 g
{0.8 lbs})
–
–
*2
Ceiling/wall
SF539
Recommended
screw
SF538
*1 E models only
*2 Make sure that the installed mount bracket can support more than 5 times of the weight of the
camera.
19
Using the side cable access hole
When installing the camera directly on the ceiling or wall with cables exposed, cut out a portion of
the dome cover to open a cable access hole.
SF549
SF539
SF548
SF538
Side cable access hole
Side cable access hole
AF
LOCK OPEN
ADJUST
The above procedure is also required when
mounting the camera using the ceiling mount
bracket WV-Q174 (option).
Method of camera installation
Using the two-gang junction box
Mount the camera on the two-gang junction box by fixing 4 screws (locally procured). (☞ Page 29)
83.5 mm {3-9/32 inches}
46 mm {1-13/16 inches}
Two-gang junction box
Direction marker for installation
Screws (locally procured)
20
Installing the camera directly on the ceiling or wall
Place the installation template label (accessory) on the ceiling or wall, and make a hole to pass the
cable.
Remove the template label, and mount the camera by fixing 4 screws (locally procured).
(☞ Page 29)
83.5 mm {3-5/16 inches}
Direction marker for installation
Side cable access hole
40
mm
{1-
4
13/ 6 mm
16
inc
hes
9/1
6 in
}
che
s}
{1-
Recommended screw (M4: 4 pcs.)
Cable access hole for ceiling/wall
20 mm {13/16 inches}
Screws
(locally procured)
Installation template label (accessory)
Using the optional ceiling mount bracket WV-Q174
SF539
SF538
It is possible to reduce the exposed portion of the
camera body using the optional ceiling mount
bracket. Refer to WV-Q174 Operating Instructions
or "Installation" (☞ page 29) for how to mount the
camera.
Using the optional ceiling mount bracket WV-Q105 (E models only)
Refer to WV-Q105 Operating Instructions and "Installation" (☞ page 29) for how to mount the camera in case of using the optional ceiling mount bracket.
Roof space
WV-Q105 (option)
Anchor bolt
Fixing screw
(4 pcs., WV-Q105 supplied)
Safety wire angle
(WV-Q105 supplied)
Safety wire
(WV-Q105 supplied)
Cable tie (accessory)
Camera
Ceiling board such
as plaster board
21
Insert/remove an SD memory card (WV-SF549/WV-SF539 only)
IMPORTANT:
• BeforeinsertingtheSDmemorycard,turnoffthepowerofthecamerafirst.
• WheninsertinganSDmemorycard,makesurethedirection.
• Before removing the SD memory card, select "Not use" for "SD memory card" on the [SD
memory card] tab of the setup menu first. Turn off the power after "Not use" selection, and then
unload the SD memory card. When the SD memory card is inserted or removed with the power
on, data in the SD memory card may be damaged.
(☞ Operating Instructions (included in the CD-ROM))
z Detach the dome cover.
SF549
(☞ Page 17)
SF539
(☞ Page 18)
SD memory card slot
x Insert
an SD memory card fully into the SD
memory card slot until a click is heard.
Label face upward
c Attach the dome cover. (☞ Page 34)
Dome cover
v When removing the SD memory card from the
SD memory card slot, detach the dome cover
(☞ page 17), and push the card until the lock is
released. After removal, attach the dome cover.
(☞ Page 34)
Dome cover fixing screw
(M3, step screw)
22
Connection
Caution:
• FORULLISTEDMODEL(S),ONLYCONNECT12VDCCLASS2POWERSUPPLY.
Before starting the connection, turn off the power of this camera and the devices to be connected.
Check and prepare the required devices and cables for connection.
Note:
{1 3
-3 0
• Since the connector storage
/1 m
6 m
in
section does not have a suffich
es
cient space, use audio cables S
}
S
t
40
30 trai
and a LAN cable that do not 17 mraigh
m
m ght
ts
m
m
m s
exceed the sizes described in
{2 ect
{1
{1 ec
1/ io
-9
-3 tio
32 n
the illustrations.
/1
/1 n
in
6
6
he
es
}
ø
{1 9 m
1/ m
32
inc
ch
s}
9 mm
{11/32 inches}
Example of
audio cable connector
in
ch
es
in
}
es
13 m
hes}
/2 inc
m {1
ch
}
Example of LAN cable
connector
z Connect the RCA pin cable to the monitor out connector for adjustment (only used for adjustment of the angular field of view).
IMPORTANT:
• Themonitoroutconnectorforserviceisprovidedonlyforcheckingtheadjustmentoftheangular field of view on the video monitor when installing the camera or when servicing. It is not provided for recording/monitoring use.
• Whencheckingtheadjustmentoftheangularfieldofviewonthevideomonitor,besuretouse
the RCA jack of the main body for connection with video monitor.
• Blackbandsmayappearatthetopandbottomorrightandleftofthescreen.(Thatdoesnot
affect the adjustment because the angular field of view is not changed.)
• Thevideooutputonthemonitorforadjustmentdoesnotguaranteethevideoperformanceor
image quality.
x Connect the microphone to MIC/LINE IN (for use of
the audio reception function). SF549
SF539
Input impedance: Approx. 2 kΩ
Recommended cable length:
1 m {3.3 feet} or less (for microphone input)
10 m {33 feet} or less (for LINE input)
Recommended microphone:
Plug-in power type microphone (option)
Connect a monaural mini plug (ø3.5 mm).
• Supplyvoltage:2.5V±0.5V
• Recommendedsensitivityofmicrophone:
–48dB±3dB(0dB=1V/Pa,1kHz)
Microphone/line
input connector
23
IMPORTANT:
• Connect/disconnecttheaudiocablesandturnonthepowerofthecameraafterturningoffthe
power of the audio output devices. Otherwise, loud noise may be heard from the speaker.
Audio output
connector
c Connect
an external speaker with amplifier to
the audio output connector (for use of the audio
transmission function). SF549
SF539
Connect a stereo mini plug (ø3.5 mm) (audio
output is monaural).
• Recommendedcablelength:10m
{33 feet} or less
v Connect
the cables of external devices to the
EXT I/O terminal plug (accessory).
q When connecting an external device, remove
8 mm - 9 mm {5/16 inches - 11/32 inches} of
the outer jacket of the cable and twist the cable
core to prevent the short circuit first.
Specification of cable (wire):
20 AWG - 26 AWG, Single core, twisted
Strip range
8 mm - 9 mm
{5/16 inches - 11/32 inches}
w Push down the button of the desired terminal
on the external I/O terminal plug with a ballpoint
pen, and release the button when the cable of
the external device is fully inserted into the terminal hole.
* Check whether the stripped part of the wire is
not exposed and is securely connected.
Button
4
3
2
1
External I/O terminal plug
(accessory)
Specification of external I/O terminal plug (accessory)
SF549
SF539
GND
ALARM IN3, AUX OUT
(Alarm input terminal 3, AUX output terminal)
4 3 2 1
ALARM IN1, DAY/NIGHT IN
(Alarm input terminal 1, DAY/NIGHT input terminal)
ALARM IN2, ALARM OUT
(Alarm input terminal 2, Alarm output terminal)
Specification of external I/O terminal plug (accessory)
GND
AUX OUT (AUX output terminal)
4 3 2 1
ALARM IN (Alarm input terninal)
ALARM OUT (Alarm output terminal)
24
SF548
SF538
e After the cable connection, connect the external I/O terminal plug to the external I/O terminals of the camera.
External I/O terminals
IMPORTANT:
• Donotconnect2wiresormoredirectlytoaterminal.Whenitisnecessarytoconnect2wires
or more, use a splitter.
• InputandoutputoftheEXTI/Oterminal2and3canbeswitchedbyconfiguringthesetting.
"Off" is selected by default. It is possible to determine whether or not to receive input from EXT
I/O terminal 2 and 3 (ALARM IN2, 3) by selecting "Off", "Alarm input", "Alarm output" or "AUX
output" for "Terminal 2" or "Terminal 3" on the [Alarm] tab on the "Alarm" page. Refer to the
Operating Instructions (included in the CD-ROM) for further information.
• Connectanexternaldevicewithverifyingthattheratingsarewithinthespecificationsbelow.
• WhenusingtheEXTI/Oterminalsastheoutputterminals,ensuretheydonotcausesignalcollision with external signals.
<Ratings>
• ALARMOUT,AUXOUT
Output specification: Open collector output (maximum applied voltage: 20 V DC)
Open: 4 V - 5 V DC by internal pull-up
Close: Output voltage 1 V DC or less (50 mA or less)
• ALARMIN
Input specification: No-voltage make contact input (4 V - 5 V DC, internally pulled up)
OFF: Open or 4 V - 5 V DC
ON: Make contact with GND (required drive
Network connector
current: 1 mA or more)
b Connect
a LAN cable (category 5 or better,
STP*) to the network connector.
* E models only
n Connect the power supply.
IMPORTANT:
• The 12 V DC power supply shall be insulated
from the commercial AC power.
25
When using 12 V DC power supply*
q Loosen the screws of the power cord plug
(accessory).
w Connect the cable of the 12 V DC power supply* to the power cord plug.
Strip 3 mm - 7 mm {1/8 inches - 9/32 inches}
from the end of the wire, and twist the stripped
part of the wire sufficiently to avoid short circuit.
Specification of cable (wire):
16 AWG - 24 AWG, Single core, twisted
• Check whether the stripped part of the wire is
not exposed and is securely connected.
e Tighten the screws of the power cord plug.
(Recommended tightening torque: 0.339 N·m
{0.25 lbf·ft})
r Connect the power cord plug to the 12 V DC
power supply terminal.
* FOR UL LISTED MODEL(S), ONLY CONNECT
12 V DC CLASS 2 POWER SUPPLY.
(GND)
(12 V DC)
Power cord plug
(accessory)
IMPORTANT:
• Besuretousethepowercordplugprovidedwiththisproduct.
• Besuretofullyinsertthepowercordplug(accessory)intothe12VDCpowersupplyterminal.
Otherwise, it may damage the camera or cause malfunction.
• Wheninstallingthecamera,makesurethatexcessiveforceisnotappliedtothepowercable.
• BesuretouseanACadaptorcompliantwiththeSpecificationsregardingpowersourceand
power consumption. (☞ Page 43)
t Run the 12 V DC output cable through the gap of the cable hook.
12 V DC output cable
Cable hook
12V=
IN
26
When using PoE (IEEE802.3af compliant)
Connect a LAN cable (category 5 or better, straight, STP*) between a PoE device (such as a hub)
and the network connector of the camera.
* E models only
IMPORTANT:
• Useall4pairs(8pins)oftheLANcable.
• Themaximumcablelengthis100m{328feet}.
• MakesurethatthePoEdeviceinuseiscompliantwithIEEE802.3afstandard.
• Whenconnectingboththe12VDCpowersupplyandthePoEdeviceforpowersupply,12V
DC will be used for power supply. Depending on the PoE device used, the power supply lamp
may not light and the network connections may not be possible. In this case, disable the PoE
device setting, and refer to the operating instructions of the PoE device in use.
• WhentheLANcableisdisconnectedonce,reconnectthecableafterabout2seconds.When
the cable is quickly reconnected, the power may not be supplied from the PoE device.
27
Connection example when connecting to a network using a
PoE hub
Speaker with amplifier
(option)
Video monitor
(for adjustment use only)
PoE device (hub)
LAN cable (category 5 or
better, straight, STP*)
Microphone (option)
LAN cable (category 5 or
better, straight, STP*)
Speaker with amplifier
(option)
Microphone (option)
PC
LAN cable (category 5 or
better, straight, STP*)
Video monitor
(for adjustment use only)
<Required cable>
LAN cable (category 5 or better, straight, STP*)
* E models only
IMPORTANT:
• Thevideomonitorisusedforcheckingtheadjustmentoftheangularfieldofviewwheninstalling the camera or when servicing. It is not provided for recording/monitoring use.
• Useaswitchinghuborarouterwhichiscompliantwith10BASE-T/100BASE-TX.
• Powersupplyisrequiredforeachnetworkcamera.WhenusingaPoEdevice(hub),12VDC
power supply is unnecessary.
28
Installation
Camera mounting
Installation shall be conducted after turning off each device.
z Detach the dome cover. (☞ Page 17)
x Connect the cables to the camera. (☞ Pages 23 - 28)
As necessary, use a cable tie (accessory) to assemble the cables.
c Mount the camera. (The illustration represents the case in which a two-gang junction box is
installed.)
Fix the camera with 4 screws (M4, locally procured).
83.5 mm {3-9/32 inches}
46 mm {1-13/16 inches}
Two-gang junction box
Direction marker for installation
(gTOP)
Direction marker for installation
(FRONTh)
Screws (locally procured)
IMPORTANT:
• Whentighteningthescrews,becarefultoensurethatthecablesdoesnottanglethecables.
Note:
• Forceilingmounting
Select which direction to face the front (the side where the Panasonic logo and "FRONTh" are)
of the camera. Refer to the "Adjustment" section (☞ pages 30 - 33) for further information
about adjustment.
• Forwallmounting
The camera shall be mounted with the "gTOP" marker facing upward.
29
Adjustment
Perform the following procedures before adjusting the camera angle.
SF549
SF548
Detach the inner dome from the camera by
picking the front and rear sides.
Note:
• Donottouchthelens.
Pick the portion marked
in the illustration as well
as the opposite side.
z Adjust
the camera angle. When determining the camera angle, repeat fine adjustments by
gradually moving the panning table, tilting table, and azimuth adjustment ring.
Horizontal position (Panning)
Loosen the panning lock screw, rotate
the panning table to adjust the pan
direction. (Adjustable range: 350 °)
Panning is possible within the range
of 180 ° (when panning clockwise)
and 170 ° (when panning counterclockwise). After adjustment, tighten
the panning lock screw to fix the panning table.
(Recommended tightening torque:
0.39 N·m {0.29 lbf·ft})
Home position
* The position where the home
position markers are aligned
Panning table
Panning lock
screw [LOCK]
Counterclockwise panning
end marker: Rotation within
the range of 170 °
30
Home position
markers K
Clockwise panning end
marker: Rotation within
the range of 180 °
Vertical position (Tilting)
Loosen the tilting lock screws (x2), and rotate
the tilting table to adjust the tilting direction.
(Adjustablerange:±75°)Sinceavariablefocal
lens is used, it is possible to change the angular field of view. This lens can also be rotated in
the reverse direction, but the image azimuth is
reversed. In this case, hold down the auto
focus (AF) button/upside-down button for 5
seconds or more. The upside-down function
starts operating and the image azimuth is modified.
Tilting lock
screws (x2)
+75 °
–75 °
Adjustable range
<Lens angular field of view (q Angle)>
Horizontal: 24.20° (TELE) to 86.60° (WIDE)
After adjustment, tighten the tilting lock screws (x2) to fix the tilting table.
(Recommended tightening torque: 0.59 N·m {0.44 lbf·ft})
Note:
• Whenthetiltingtableisturnedtotheedgeoftheadjustablerange(±75°),itmustbenoted
that the shadow of the dome cover may be projected.
• Whenthecameraisinstalledtoawall,theimageisturnedupsidedowninthedefaultsettings.
The way the image is displayed can be corrected in three ways: rotating the panning table 180°
clockwise, holding down the auto focus (AF) button/the upside-down button for 5 seconds or
more and operating the upside-down function, or selecting "On" for "Upside-down" from the
setup menu. For information about performing the "Upside-down" setting from the setup
menu, refer to the Operating Instructions (included in the CD-ROM).
Image tilt adjustment
Rotate the azimuth adjustment ring to adjust the azimuth angle of the image.
(Adjustablerange:±100°)
Adjustable range
–100 °
+100 °
Azimuth adjustment ring
31
x Adjust the angular field of view and the focus.
Adjust the angular field of view in accordance with the distance between the camera lens and a
photographic subject. These adjustments shall be performed together with the camera angle
adjustment.
Auto focus (AF) button/Upside-down button
Zoom lock knob
Loosen
Tighten
Focus ring
* Do not move the focus ring.
q Loosen the zoom lock knob and move the knob between TELE and WIDE to obtain the appropriate angle of view.
w Press the auto focus (AF) button twice quickly to perform basic adjustments. The lamp blinks
during auto focus (AF) adjusting. When the adjustment is completed, adjust the viewing angle
while watching the screen.
Note:
• The focus may not be adjusted appropriately when the zoom lock knob is positioned at the "W"
(or "T") end. In this case, adjust the focus again by slightly moving the zoom lock knob to the
direction of "T" (or "W").
e To adjust the angular field of view with a higher zooming effect even after turning the zoom lock
knobalmostfullyinthe"T"direction,adjustthezoomratiotothe“Tele”sideonthe[Extraoptical zoom] tab on the setup menu. For information about performing the "Extra optical zoom"
setting from the setup menu, refer to the Operating Instructions (included in the CD-ROM).
r Tighten the zoom lock knob.
t After fixing the viewing angle, press the auto focus (AF) button once. The auto focus lamp lights
for about 10 seconds, and a detailed adjustment for the focus is automatically performed.
IMPORTANT:
• Donotmovethefocusringbyhand.
• Defocus may be caused by the reinstalled dome cover. In this case, perform the auto focus
function from the setup menu.
• Presstheautofocus(AF)buttontwicequicklytoperformbasicadjustmentsinashorttime.For
more accurate adjustments use the detailed adjustments.
• Afterperformingbasicadjustments,makesuretopresstheautofocus(AF)buttononcetoperform detailed adjustments.
32
Note:
• Ifthezoomlockknobisfullyturnedinthe"W"direction,theperipherymaybecomedark.In
such a case, turn the zoom lock knob in the "T" direction for readjustment.
• Ifthezoomlockknobisslightlytightenedbeforethezoomisadjusted,theknobwillbecome
stable, making fine adjustments easier to perform.
• When shooting in the following place or the following subjects, focus may not be adjusted
automatically. In this case, adjust the focus manually from the setup menu. Refer to the
Operating Instructions (included in the CD-ROM) for how to perform the manual focus adjustment from the setup menu.
• Subj.movingfrequently
• Subj.withlargeilluminancechange
• Subj.withlowilluminance
• Subj.withreflectionorextrabrightness
• Subj.throughawindow
• Placewherethedomecovereasilybecomesdirty
• Subj.withlesscontrastsuchaswhitewall
• Subj.withheavyflicker
• Whenimagesinthenear-infraredlightareachangefrom color to black & white, out-of-focus
may be occurred according to the nature of optical property. In this case, the focus can automatically be corrected by selecting "Auto" or "Preset" for "Adjusting method" on the setup
menu (The focus will not automatically be adjusted according to the illumination level change
once the focus is corrected). Refer to the Operating Instructions (included in the CD-ROM) for
how to set "Adjusting method" on the setup menu.
• It may be difficult to tighten the zoom lock knob depending on the position of the azimuth
adjustment ring. In this case, adjust the azimuth adjustment ring after tightening the zoom lock
knob.
33
Attaching the dome cover
Attach the dome cover to the camera. SF549
SF548
The following procedure is required when using WV-SF549 or WV-SF548. Refer to page 35 when
using WV-SF539 or WV-SF538.
z Attach the inner dome to the camera in the
same manner as the procedure in page 30.
Make sure that the tilting lock screws of
the camera and the holes on the inner
dome are correctly fit together.
x Attach
T
ON
FR P
TO
the dome cover using the bit for
tamperproof screw (accessory).
(Recommended tightening torque:
0.59 N·m {0.44 lbf·ft})
MONI
OUTO
T R
CK
LO
c After the installation is complete, remove
the cover film from the dome section.
v Push down the auto focus (AF) button with
a ballpoint pen to adjust the focus again.
Refer to page 30 for further information
about adjustment.
Auto focus (AF)
button
34
SF538
Attach the dome cover to the camera. SF539
The following procedure is required when using WV-SF539 or WV-SF538. Refer to page 34 when
using WV-SF549, WV-SF548.
Marker
z Align the indication "OPEN" to the marker
of the camera to attach the dome cover.
Dome alignment
indication "OPEN"
AF
LOCK
OPEN
ADJUST
Dome
cover
Dome section
x Remove
the cover film from the dome
cover except the dome section.
c Adjust the direction of the inner dome.
Rotate the dome cover clockwise to adjust
the marker to "ADJUST". The clear dome
and the inner dome can rotate together in
this state. Rotate the dome section of the
dome cover to adjust the direction so that
no eclipse may be caused.
AF
OPEN
LOCK
ADJUST
IMPORTANT:
• Forinnerdomeadjustments,adjustthemarkertothe"ADJUST"position.Ifthedomesection
is moved with unreasonable force from the "LOCK" position, this may be a cause of destruction.
35
v Rotate the dome cover clockwise to adjust
the marker to "LOCK".
AF
OPEN
LOCK
ADJUST
b Fix
the dome cover and the camera with
the dome cover fixing screw (M3, step
screw, x1) that has been removed in the
procedure of "Detaching the dome cover"
(☞ page 17).
(Recommended tightening torque:
0.59 N·m {0.44 lbf·ft})
AF
LOCK OPEN
ADJUST
n After
the installation is complete, remove
the cover film, which was removed halfway
in Step 2, completely from the dome section.
m Push down the auto focus (AF) button with
a ballpoint pen to adjust the focus again.
Refer to page 30 for further information
about adjustment.
Dome cover fixing screw
(M3, step screw)
AF
OPEN
LOCK
ST
ADJU
Auto focus (AF) button
36
Using the CD-ROM
About the CD launcher
Insert the provided CD-ROM into the CD-ROM drive of your PC to start up the CD launcher. Then the
License Agreement will be displayed.
• Ifthelauncherwindowisnotdisplayed,doubleclickthe"CDLauncher.exe"fileontheCD-ROM.
• Read theAgreementandchoose"Iaccepttheterminthelicenseagreement",andclick[OK].
Thenthelauncher window will be displayed.
q
w
e
r
t
UsingthesuppliedCD-ROM,thefollowingactionscanbeperformed.
q ThePanasonicIPsettingsoftwarecanbeinstalledonthePC.
→ Referto"InstallingPanasonicIPsettingsoftware".(☞Page38)
w Settingsrelatedtothecamera'snetworkcanbesetfromthePanasonicIPsettingsoftware.
→ Referto"Configurethenetworksettings".(☞Page40)
e ThemanualscanbeinstalledonthePC.
→ Referto"Installingthemanuals".(☞Page39)
r YoucanalsoviewthemanualswithoutinstallingthemtothePCbyclickingthe[Open]button.
Youcanselecttoviewthemanualsor"NotesonWindows® / Internet Explorer®versions"from
thedisplayedmenu.
t TheViewersoftwarecanbeinstalledonthePC.
→ Referto"InstallingtheViewersoftware".(☞Page39)
MakesuretoreadthereadmefileontheprovidedCD-ROMbeforeusingthesoftware.
37
Installing Panasonic IP setting software
OntheCDlauncherwindow,clickthe[Install]buttonnextto[IPSettingSoftware]todisplaythePanasonic
IPsettingsoftwareinstallationwindow.Confirmthefollowingsettingsbeforestartingtheinstallation.
q
w
e
r
q SelectthePanasonicIPsettingsoftwaretoinstall.
w SelectwheretocreatethePanasonicIPsettingshortcuticonwhenthePanasonicIPsetting
software is installed.
e SpecifywhichfolderonthePCtoinstallthePanasonicIPsettingsoftwareto.
r Clickthe[Install]buttontostarttheinstallation.
Note:
• TouninstallthePanasonicIPsettingsoftwaredeletetheshortcuticonfromwhereyouspecified
ittobeinstalled(thedefaultisonthedesktop)duringinstallationandthe[EasyIPConfig]folder
from the folder you specified during Panasonic IP setting software installation.
38
Installing the manuals
OntheCDlauncherwindow,clickthe[Install]buttonnextto[Manual]todisplaytheManualinstallationwindow.Confirmthefollowingsettingsbeforestartingtheinstallation.
w
q
e
r
t
q Selectwhichmanualstoinstall.Thecameramodelsthatthemanualssupportaredisplayedin
w"ModelList".
w Thecameramodelsthataresupportedbythemanualsselectedinqaredisplayedhere.
e Selectwheretocreatethemanualsshortcuticonwhenthemanualsareinstalled.
r SpecifywhichfolderonthePCtoinstallthemanualsto.
t Clickthe[Install]buttontostarttheinstallation.
Note:
• Touninstallthemanualsdeletetheshortcuticonfromwhereyouspecifiedittobeinstalled(the
default is on the desktop) during installation and the [Manual] folder from the folder you
specified during the manuals installation.
Installing the Viewer software
The Viewer software (Network Camera View 4S) must be installed on the PC in order to display
cameraimages.OntheCDlauncherwindow,clickthe[Install]buttonnextto[ViewerSoftware],and
followtheinstructionsdisplayedonthewindowtoinstallthesoftware.Amessageisdisplayedifa
PCthatdoesnothavetheViewersoftwareinstalledtriestoaccessthecamera.Installthesoftware
byfollowingtheinstructionsdisplayedonthewindow.Referto"Viewersoftware"intheOperating
Instructionsforfurtherinformation.
Note:
• TouninstalltheViewersoftware,followthestepsbelowfordependingontheOSusedonyour
PC.
Windows XP:
Delete[NetworkCameraView4S]from[ControlPanel]-[AddorRemovePrograms].
Windows Vista/Windows 7:
Delete[NetworkCameraView4S]from[ControlPanel]-[Programs]-[Uninstallaprogram].
39
Configure the network settings
Configure the network settings of the camera using the
Panasonic IP setting software
ItispossibletoperformthenetworksettingsofthecamerausingtheIPsetupsoftwareontheprovidedCD-ROM.Whenusingmultiplecameras,itisnecessarytoconfigurethenetworksettingsof
eachcameraindependently.
IfthePanasonicIPsettingsoftwaredoesnotwork,configurethenetworksettingsofthecamera
and the PC individually on the "Network" page of the setup menu. Refer to the Operating
Instructions(includedintheCD-ROM)forfurtherinformation.
IMPORTANT:
• When using Microsoft Windows 7 or Microsoft Windows Vista, the "Windows Security Alert"
window may be displayed when starting the IP setup software. In this case, disable "User
AccountControl"fromthecontrolpanel.
• Forthesecurityenhancement,theMACaddress/IPaddressofthecameratobeconfiguredwill
notbedisplayedwhenaround20minuteshavepassedafterturningonthepowerofthecamera.(Whentheeffectiveperiodissetto"20min"intheIPsetup)
Howevercamerasintheinitialsetmodearestilldisplayedevenafter20minutes.
• PanasonicIPsettingsoftwareisinoperableinothersubnetsviathesamerouter.
• ThiscameracannotbedisplayedorsetwithanolderversionoftheIPsetupsoftware(version2.xx).
z TostartthePanasonicIPsettingsoftware,clickthe[Run]buttonnextto[IPSettingSoftware]
fromtheCDlaunchermenuwindow,ordouble-clickontheshortcuticoncreatedafterinstallingthesoftwareonthePC.
• TheLicenseAgreementwillbedisplayed.ReadtheAgreementandchoose"Iaccepttheterm
inthelicenseagreement",andclick[OK].
x Clickthe[NetworkSettings]buttonafterselect-
ingtheMACaddress/IPaddressofthecamera
tobeconfigured.
Note:
• WhenusingaDHCPserver,theIPaddressassignedtothecameracanbedisplayedbyclickingthe[Search]buttonoftheIPsettingsoftware.
• When a duplicate IP address is used, the corresponding camera number will be displayed
shaded.
• When the [Access Camera] button is clicked, live images of the selected camera will be displayed.
• Itispossibletochangethe"Cameralist"displaybetweenIPv4addressesandIPv6addresses
inaccordancewiththeprotocolinuse.
• Theinformationdisplayedcanbesortedbyclickingthetitleofeachdisplayeditem.
40
c Complete each network setup item and click the [Save]
button.
Note:
• By unchecking the "Wait for camera restarting." checkbox,multiplecamerascanbecontinuouslyconfigured.
IMPORTANT:
• Itmaytakeforaround2minutestocompletetouploadthesettingstothecameraafterclicking
the[Save]button.ThesettingsmaybeinvalidatedwhentheLANcableisdisconnectedbefore
completingtheupload.Inthiscase,performthesettingsagain.
• Whenusingafirewall(includingsoftware),allowaccesstoallUDPports.
About the default user name and password
Clickthe[Setup]buttononthe"Live"page,theuserauthenticationwindowwillbedisplayed.Enter
thedefaultusernameandpasswordasfollows,andlogin.
Username:admin
Password:12345
IMPORTANT:
• Toenhancethesecurity,changethepasswordfortheusername"admin".Itisrecommended
tochangethispasswordperiodically.
• To enhance the security of the "Live" page, it is possible to set authentication for the "Live"
page by selecting "On" for "User auth.". Refer to the Operating Instructions (included in the
CD-ROM)forfurtherinformation.
41
Troubleshooting
Before asking for repairs, check the symptoms with the following table.
Contact your dealer if a problem cannot be solved even after checking and trying the solution in the
table or a problem is not described below.
Cause/solution
Reference
pages
Power is not turned on.
When using DC power supply
•Is12VDCpowersupplyconnectedto
the power supply terminal?
→ Check whether the connection is
appropriately established.
•IstheACadaptorinusecompliantwith
the Specifications?
→ Check the Specifications regarding
AC adaptor.
When using a PoE device for power
supply
•ArethePoEdeviceandthenetwork
connector on the rear of the camera
connected using a LAN cable (4-pair)?
→ Check whether the connection is
appropriately established.
•DependingonthePoEdevice,the
power supply will stop when the
demanded power exceeds its total
power limit for all PoE ports.
→ Refer to the operating instructions of
the PoE device in use.
26 - 27
The focus cannot be
adjusted.
•Isthezoomlockknobturnedtothe
"W" (or "T") end?
→ Adjust the focus again by slightly
moving the zoom lock knob to the
direction of "T" (or "W").
32 - 33
Symptom
42
Specifications
• Basic
Power source:
Power consumption:
12 V DC, PoE (IEEE802.3af compliant)
SF549
SF539
12 V DC*: 530 mA, PoE 48 V: 120 mA (Class 2 devices)
SF548
Ambient operating temperature:
Ambient operating humidity:
Shock resistance:
SF538
12 V DC*: 510 mA, PoE 48 V: 115 mA (Class 2 devices)
* FOR UL LISTED MODEL(S), ONLY CONNECT 12 V DC CLASS
2 POWER SUPPLY.
–10 °C to +50 °C {14 °F to 122 °F}
Less than 90 % (no condensation)
SF549
SF548
Compliant with 20 J (IEC 60068-2-75)/IK10 (IEC 62262)
Monitor output (for adjusting
the angular field of view):
External I/O terminals:
VBS:1.0V[p-p]/75Ω,compositesignal,RCAjack
SF549
SF539
ALARM IN1/ DAY/NIGHT IN,
ALARM IN2/ ALARM OUT,
ALARM IN3/ AUX OUT (x1 for each)
SF548
SF538
ALARM IN, ALARM OUT, AUX OUT (x1 for each)
Microphone/line input cable:
For microphone input:
For line input:
Audio output cable:
SF549
SF539
ø3.5 mm monaural mini jack
Input impedance: Approx. 2 kΩ
Applicable microphone: Plug-in power type
Supplyvoltage:2.5V±0.5V
Input level: Approx. –10 dBV
SF549
SF539
ø3.5 mm stereo mini jack (monaural output)
Output impedance: Approx. 600 Ω
Line level
Dimensions:
SF549
SF548
ø132 mm x 102.5 mm (H) {ø5-3/16 inches x 4-1/32 inches (H)}
SF539
SF538
ø129.5 mm x 93 mm (H) {ø5-1/8 inches x 3-11/16 inches (H)}
Mass:
SF549
SF548
Approx. 710 g {1.57 lbs}
SF539
SF538
Approx. 450 g {0.99 lbs}
Finish:
SF549
SF548
Main body: Aluminum die cast, sail white
Dome section: Clear polycarbonate resin
SF539
SF538
Main body: ABS resin, sail white
Dome section: Clear acrylic resin
43
• Camera
Image sensor:
Effective pixels:
Scanning area:
Scanning system:
Minimum illumination:
1/3-type MOS image sensor
Approx. 3.1 megapixels
4.51 mm (H) × 3.38 mm (V) {3/16 inches (H) x 1/8 inches (V)}
Progressive
SF549
SF539
Color: 0.5 lx {0.05 footcandle}
(F1.3, Auto slow shutter: Off (1/30 s), Gain: On(High))
0.03 lx {0.003 footcandle}
(F1.3, Auto slow shutter: max. 16/30 s, Gain: On(High))*
BW: 0.06 lx {0.006 footcandle}
(F1.3, Auto slow shutter: Off (1/30 s), Gain: On(High))
0.004 lx {0.0004 footcandle}
(F1.3, Auto slow shutter: max. 16/30 s, Gain: On(High))*
SF548
Super-Dynamic:
Dynamic range:
Gain (AGC):
Adaptive black stretch:
Light control mode setting:
Shutter speed:
Auto slow shutter:
Day & Night (IR):
SF538
Color: 0.5 lx {0.05 footcandle}
(F1.3, Auto slow shutter: Off (1/30 s), Gain: On(High))
0.03 lx {0.003 footcandle}
(F1.3, Auto slow shutter: max. 16/30 s, Gain: On(High))*
BW: 0.3 lx {0.03 footcandle}
(F1.3, Auto slow shutter: Off (1/30 s), Gain: On(High))
0.02 lx {0.002 footcandle}
(F1.3, Auto slow shutter: max. 16/30 s, Gain: On(High))*
* Converted value
On/Off
52 dB typ. (only at Super-Dynamic On)
On(High)/ On(Mid)/ On(Low)/ Off
On/Off (only at Super-Dynamic Off)
Outdoor scene/Indoor scene (50 Hz/60 Hz)/ Fix shutter
1/30, 3/100, 3/120, 2/100, 2/120, 1/100, 1/120, 1/250,
1/500, 1/1000, 1/2000, 1/4000, 1/10000 (only at SuperDynamic Off)
Off (1/30 s), max. 2/30 s, max. 4/30 s, max. 6/30 s,
max. 10/30 s, max. 16/30 s
SF549
SF539
On/ Off/ Auto1/ Auto2
Day & Night (electrical):
White balance:
Digital noise reduction:
Video analytics
Face detection:
Privacy zone:
VIQS:
Camera title on screen:
Video motion detection
(VMD alarm):
44
SF548
SF538
Off/Auto
ATW1/ ATW2/ AWC
High/Low
On/Off (with the XML notification setting)
Gray/Off (up to 2 zones available)
On/Off (up to 2 areas available)
Up to 20 characters (alphanumeric characters, marks)
On/Off
On/Off, (up to 4 areas available)
• Lens
Zoom ratio:
3.6x
Extra optical zoom: 10.8x (Imaging mode: 2 megapixel, at
640x360 resolution)
Focal length:
2.8 mm - 10 mm
Maximum aperture ratio:
1:1.3 (WIDE) - 1:3.0 (TELE)
Angular field of view:
Horizontal: 24.20° (TELE) - 80.6° (WIDE) (Imaging mode: [16:9])*
Adjusting angle:
Horizontal: 180 ° (clockwise), 170 ° (counterclockwise)
Vertical: ±75 °
Image tilt adjustment range: ±100 °
* If "1.3 megapixel [4:3]" is selected for the imaging mode, the viewing angle will become narrower.
• Network
Network:
Resolution:
Image compression method*1:
Transmission interval:
10BASE-T/100BASE-TX, RJ45 connector
Imaging mode: 2 megapixel [16:9]
H.264
1920x1080/ 640x360/ 320x180 max.30 fps
JPEG(MJPEG)
1920x1080/ 640x360/ 320x180 max.30 fps
Imaging mode: 1.3 megapixel [16:9]
H.264
1280x720/ 640x360/ 320x180 max.30 fps
JPEG(MJPEG)
1280x720/ 640x360/ 320x180 max.30 fps
Imaging mode: 1.3 megapixel [4:3]
H.264
1280x960/ VGA(640x480)/ QVGA(320x240)
max.30 fps
JPEG(MJPEG)
1280x960/ VGA(640x480)/ QVGA(320x240)
max.30 fps
Imaging mode: 3 megapixel [4:3]
H.264
1280x960/ max.15 fps
JPEG(MJPEG)
2048x1536/ max.15 fps
H.264
Image quality: Low/ Normal/ Fine
Transmission type: Unicast/Multicast
Bit rate:
Constant bit rate/Best effort: 64 kbps/ 128 kbps/ 256 kbps/
384 kbps/ 512 kbps/ 768 kbps/ 1024 kbps/ 1536 kbps/
2048 kbps/ 3072 kbps/ 4096 kbps/ 8192 kbps/
10240 kbps/ 12288 kbps/ 14336 kbps
Frame rate:
1 fps/ 3 fps/ 5 fps/ 7.5 fps/ 10 fps/ 12 fps/ 15 fps/ 20 fps/
30 fps
JPEG (MJPEG)
Image quality:
0 SUPER FINE/ 1 FINE/ 2/ 3/ 4/ 5 NORMAL/ 6/ 7/ 8/
9 LOW (10 steps: 0-9)
Transmission type: PULL/PUSH
0.1 fps - 30 fps (JPEG frame rate will be restricted when displaying both JPEG and H.264 images.)
45
Cropping function:
Picture in picture function:
Audio compression
method:
Bandwidth control:
Protocol:
OS*2 *3:
Browser:
Maximum concurrent
access number:
FTP client:
Multi-screen:
Compatible SDXC/SDHC/
SD memory card (option):
Cellular phone compatibility:
Mobile terminal compatibility:
(As of January, 2012)*4
2megapixel[16:9]
H.264 640x360/ 320x180 max.30 fps
MJPEG 640x360/ 320x180 max.30 fps
1.3megapixel[16:9]
H.264 640x360/ 320x180 max.30 fps
MJPEG 640x360/ 320x180 max.30 fps
1.3megapixel[4:3]
H.264 VGA(640x480)/ QVGA(320x240) max.30 fps
MJPEG VGA(640x480)/ QVGA(320x240) max.30 fps
Off/ Live/ Alarm trigger 1/ Alarm trigger 2/ Alarm trigger 3/ Alarm trigger 4
(only at Cropping function Off)
G.726 (ADPCM) 32 kbps/ 16 kbps
G.711 64 kbps
Unlimited/ 64 kbps/ 128 kbps/ 256 kbps/ 384 kbps/ 512 kbps/
768 kbps/ 1024 kbps/ 2048 kbps/ 4096 kbps/ 8192 kbps
IPv6: TCP/IP, UDP/IP, HTTP, HTTPS, RTP, FTP, SMTP, DNS,
NTP, SNMP, DHCPv6, MLD, ICMP, ARP
IPv4: TCP/IP, UDP/IP, HTTP, HTTPS, RTSP, RTP, RTP/RTCP,
FTP, SMTP, DHCP, DNS, DDNS, NTP, SNMP, UPnP, IGMP,
ICMP, ARP
Microsoft Windows 7
Microsoft Windows Vista
Microsoft Windows XP SP3
Windows Internet Explorer 9.0 (32-bit)
Windows Internet Explorer 8.0 (32-bit)
Windows Internet Explorer 7.0 (32-bit)
Microsoft Internet Explorer 6.0 SP3
14 (Depends on network conditions)
Alarm image transmission, FTP periodic transmission (When the
FTP transmission is failed, backup on an optional SD memory
SF539 )
card is available. SF549
Up to 16 camera images can be displayed simultaneously on a
multi-screen. (Including the camera itself)
SF549
SF539
Manufactured by Panasonic
SDXC memory card: 64 GB
SDHC memory card: 4 GB, 8 GB, 16 GB, 32 GB
SD memory card: 1 GB, 2 GB
(except miniSD card and microSD card)
JPEG image, AUX control (by access level)
iPad, iPhone, iPod touch (iOS 4.2.1 or later)
AndroidTM mobile terminals
*1 Transmission for 2 streams can be individually set to transmission.
*2 For further information about PC system requirements and precautions for when using Microsoft
Windows 7, Microsoft Windows Vista, or Windows Internet Explorer, click "Manual" - "Open"
from the supplied CD-ROM and refer to "Notes on Windows® / Internet Explorer® versions".
*3 When using IPv6 for communication, use Microsoft Windows 7 or Microsoft Windows Vista.
*4 For further information about compatible devices, refer to our website
(http://panasonic.net/pss/security/support/info.html).
46
Standard accessories
Installation Guide (this document) ............................................... 1 pc.
Warranty card (P model only) ..................................................... 1 pc.
CD-ROM*1 ................................................................................ 1 pc.
Code label*2 .............................................................................. 1 pc.
The following parts are used during installation procedures.
Power cord plug ........................................................................ 1 pc.
External I/O terminal plug ........................................................... 1 pc.
Installation template label ........................................................... 1 pc.
Cable tie ............................................................ 2 pcs. (incl. 1 spare)
Bit for tamperproof screw SF549
SF548 .......................... 1 pc.
*1 The CD-ROM contains the operating instructions and different kinds of tool software programs.
*2 This label may be required for network management. The network administrator shall retain the
code label.
Optional accessories
User License Accessory (For H.264) ...................BB-HCA8A (P model)
BB-HCA8CE (E model, Korea)*
* Required in Korea
SF538
Dome cover (Smoke type) SF539
WV-CF5S
SF538
Ceiling Mount Bracket SF539
WV-Q174
Ceiling Mount Bracket
WV-Q105 (E models only)
47
Information for Users on Collection and Disposal of Old Equipment and used
Batteries
These symbols on the products, packaging, and/or accompanying documents mean that
used electrical and electronic products and batteries should not be mixed with general
household waste.
For proper treatment, recovery and recycling of old products and used batteries, please
take them to applicable collection points, in accordance with your national legislation and
the Directives 2002/96/EC and 2006/66/EC.
By disposing of these products and batteries correctly, you will help to save valuable
resources and prevent any potential negative effects on human health and the environment
which could otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products and batteries, please
contact your local municipality, your waste disposal service or the point of sale where you
purchased the items.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national
legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or
supplier for further information.
[Information on Disposal in other Countries outside the European Union]
These symbols are only valid in the European Union. If you wish to discard these items,
please contact your local authorities or dealer and ask for the correct method of disposal.
Cd
Note for the battery symbol (bottom two symbol examples):
This symbol might be used in combination with a chemical symbol. In this case it complies
with the requirement set by the Directive for the chemical involved.
For U.S. and Canada:
For Europe and other countries:
Panasonic System Communications
Company of North America,
Unit of Panasonic Corporation
of North America
Panasonic Corporation
www.panasonic.com/business/
For customer support, call 1.800.528.6747
Three Panasonic Way, Secaucus,
New Jersey 07094 U.S.A.
http://panasonic.net
Importer's name and address to follow EU rules:
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg F.R.Germany
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga,
Ontario, L4W 2T3 Canada
(905)624-5010
www.panasonic.ca
© Panasonic System Networks Co., Ltd. 2012
Cs0412-1042
PGQX1075YA
Printed in China
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement