model th111gfci-p (120 vac)

model th111gfci-p (120 vac)
1) Connecting wires and mounting thermostat
Connect the rear thermostat wires
to the power supply and to the
load using solderless connectors
for copper wires. See schematic
diagram.
MODEL TH111GFCI-P (120 VAC)
SUMMARY
u
OPTIONS SELECTION
At the back of the thermostat, there are three selection switches to set at
your preferences.
Temperature in °C or °F, time in 12 or 24 hours and early start function.
u
TO SET TIME AND DAY
Press on DAY, HOUR and MIN buttons to adjust time and day.
u
TO RECORD THE
(COMFORT) SETPOINT TEMPERATURE
Select chosen setpoint temperature by using
or
button. Press on
button (2 to 3 seconds) until icon appears on display.
2) Connecting temperature sensor wire
Runs the program.
or
shows temperature setting
and can override temporarily your programming up to the
next program
MAN:
Maintains the selected temperature.
the temperature setting.
Power-up
u
CHECKING GROUND FAULT CIRCUIT INTERRUPTER (GFCI)
Adjust the setpoint temperature until heating indicator (
) appears on
display. Press on TEST button. The test is conclusive if the warning light
(GFI) on thermostat is ON and power to the load is cut-off (
remain
on display though). If these events do not occur, check the installation.
Press on RESET button to reset the GFCI.
OPERATING MODES
To select an operating mode, use MODE button.
or
changes
60 HZ
WARNING : Special CO/ALR solderless connectors must be used when
connecting with aluminum conductors.
AUTO:
TO RECORD THE
(ECONOMIC) SETPOINT TEMPERATURE
Select chosen setpoint temperature by using
or
button.
Press on button (2 to 3 seconds) until icon appears on display .
120 VAC
Note 1 : All cables and
connections must conform to the
local electrical code.
Connect the temperature sensor
wire to the two lower screws of the
terminal block at the back of the
thermostat (no polarity need to be
respected). The wire must pass
outside the electrical box and follow the wall down to the floor. The
sensing probe should be placed in
a representative heat area for
maximum system perfomance.
The sensing probe should be centered between the wires in the
mat. The temperature sensor wire
cannot cross any heater wires and
the sensing probe must not be
directly or adjacent to a heating
wire.
u
u
Push the excess wire back into
the electrical box to prevent
interference with the thermostat.
Secure the thermostat using two
(2) 6-32 screws . Once the thermostat is properly installed, return
power to heating system.
120 VAC
60 HZ
To power up thermostat:
When power is applied for the first time, the
display must show the time 00:00, the floor
temperature and the manual mode icon (
).
Other information might show up on the display if
installation is defective or does not comply with
the instructions. The warning light (GFI) must be
off.
The message L0 or HI will appear on the display
if the temperature sensor is defective or the
temperature is below 0 °C (32 °F) or higher than
60 °C (140 °F). Also, the heating indicator will be
present on display and the relay will be closed
(current going in the load).
Checking ground fault circuit interrupter (GFCI)
Adjust the setpoint temperature until
heating indicator (
) appears on
display. Press on TEST button. The test is
conclusive if the warning light (GFI) on the
thermostat is ON and power to the load is
cut-off. If these events do not occur, check
the installation. Press on RESET button to
reset the GFCI.
If the GFCI test fails:
Check the load wires. The thermostat
must be in heating mode to carry out the
test (heating indicator ON).
The GFCI test should be carried out
monthly. If the test fails, cut off the electric
power to the heating system and call
customer service or return the thermostat
to your supplier for verification. If the
warning light comes on during normal
operation, cut off power to the heating
system and have an electrician verify the
installation.
INSTALLATION
This thermostat is designed to control floor electric heating systems. The
resistive load must not exceed 2000 watts (NI) @ 120 VAC (16.7 A). The
thermostat is equipped with a ground fault circuit interrupter (GFCI) and therefore
the isolation of the line and load are required for operation. The polarity of line
connection (line and neutral) must be respected. During a ground fault, only the
current in the black wire (line) of the load will be cut-off. Connect thermostat as
shown on diagram.
OPERATING MODES
The TH111GFCI-P have two (2) operating modes.
MANUAL (
Electricians or experienced technicians should install the thermostat.
)
This mode allows you to maintain a constant temperature of the floor.
This thermostat is designed to be used with a self-protected heating system
equipped with thermal cut off and circuit breaker.
1- To activate this mode, press on Mode button to display the
PARTS INCLUDED
2- Set the desired temperature using the
pre-programmed
or
or
settings.
(To select the
setting, press on
and
-
One (1) TH111 GFCI-P (120 VAC) thermostat
Two (2) 6-32 screws
Four (4) solderless connectors (for copper wire)
One (1) Temperature sensor with a 15 foot extension
TURN OFF POWER OF THE HEATING SYSTEM AT THE MAIN POWER
PANEL TO AVOID ELECTRICAL SHOCK. Keep air vents of the thermostat
clean and free from obstructions.
AUTOMATIC (
icon.
buttons or select the
simultaneously.)
)
This mode executes your own programming.
To activate this mode, press on Mode button to display the
icon.
The
or
icon indicates which temperature setting is used. Also, the icon
of the program number will be shown.
720-111003-A
1/2
Memory back-up
d) Exemple 2 :
In the event of a power failure, an internal circuit will maintain the programming
and the time. But only the time could have to be set if power failure is more than
6 hours.
Comfort period: Monday to Friday from 6:15 AM to
8:15 AM and from 5:00 PM to 10:00 PM.
MON.
Schedule/Day
TUES.
WED.
THU.
FRI.
SAT.
SUN.
PROG. 1
6:15 AM 6:15 AM 6:15 AM 6:15 AM 6:15 AM 7:30 AM 7:30 AM
Early start function
PROG. 2
8:15 AM 8:15 AM 8:15 AM 8:15 AM 8:15 AM
The thermostat is providing a built-in function enabling it to calculate the optimum
time to start the heating system to achieve the desired temperature setting at the
programmed time. This function could start the heating system as early as 6
hours prior ti the programmed time. To enable this function, set the switch E.S. to
“ON” at the back of the thermostat.
PROG. 3
5 PM
5 PM
5 PM
5 PM
5 PM
---
---
PROG. 4
10 PM
10 PM
10 PM
10 PM
10 PM
11 PM
11 PM
NOTE :
---
---
It is faster to program the same schedule for every day and then
modify the exception days.
1- Press on PGM button to access the programming mode.
PROGRAMMING
2- Press on Day button 3 seconds to select every day of the week.
3- Press on Hour and Min buttons to enter 6:15 AM Prog. 1, (
Programming the time and day
4- Press on PGM button to select Prog. 2 (
enter 8:15 AM.
1-Set the time using the Hour and Min buttons.
2-Set the day using the Day button.
).
) and Hour and Min buttons to
5- Repeat step 4 to enter Prog. 3 (5:00 PM) and Prog. 4 (10:00 PM).
Programming the Comfort, Economic and Vacation settings
The Comfort
, Economic
and Vacation
settings respectively represent
the temperatures that you wish to have during the day
, at night
or while
you are away at work
, or while you are away for an extended period
.
NOTE : When making modifications, make sure you are in the right
program.
To modify the Saturday and Sunday schedules:
6- Press on Day button until SA or SU is displayed.
To program your settings
a)
b)
To program the Comfort temperature, select the desired degree using the
buttons and press the
button until the
icon is displayed
(app. 3 seconds).
To program the Economic temperature, select the desired degree using the
buttons and press the
button until the
icon is displayed
(app. 3 seconds).
c)
To program the Vacation temperature, select the desired degree using the
buttons and press on the
and
buttons simultaneously
until the
icon is displayed (app. 3 seconds).
d)
Press the Mode button to exit this function and return to the normal
operating mode.
Schedule programming
The TH111GFCI-P allows 4 setting changes for each day of the week. There are
no pre-set programs.The programs are tailored to perfectly adapt to your life
style. The principle is very simple. For each day, enter the time at which you wake
up (P1), the time you leave for work (P2), the time you arrive back home (P3) and
the time you go to bed (P4).
Mode
Program
NOTE :
Time
1
Wake-up time
2
Leaving time
3
Return time
4
Bed time
For temperature increases (Prog. 1 and 3), allow at least
15 minutes per °C. If you have lowered the temperature by
3 °C during the night and you wake up at 7 AM, change the
setting at 6:15 AM.
7- Press on PGM button to select Prog. 1 (
buttons to enter 7:30 AM.
) and Hour and Min
8- Press on PGM button to select Prog. 2 (
erase it.
) and then Clear button to
9- Press on PGM button to select Prog. 3 (
erase it.
) and then Clear button to
10- Press on PGM button to select Prog. 4 (
buttons to enter 11:00 PM.
) and then Hour and Min
11- Press on Mode button to exit this function.
Temporary or permanent temperature bypass
This operation allows you to temporarily modify the floor temperature while you
are in the Automatic mode. Simply press on
or
buttons to select the desired
temperature, or the
or
button to select the Comfort or Econo settings you
have programmed.This temperature will be maintained until the beginning of the
next programmed schedule.
You can also switch to the Vacation setting for a prolonged absence by pressing
on
and
at the same time.The display will show
icon. In that case,
the temperature bypass is permanent. To return to the normal operating mode,
press on Mode button.
If you wish to immediately return to the programmed settings, press on Mode
button twice.
CHARACTERISTICS
• Model:
TH111GFCI-P (120 VAC)
• Supply:
120 VAC, 50/60 Hz
• Load:
16.7 A maximum (Resistive only)
• Power:
2000 watts (NI) @ 120 VAC
• Ground fault circuit interrupter (GFCI): Class A (5 mA TRIP LEVEL)
• Approvals:
CSA / C, US
For savings to be obtained, you must lower the temperature for a period of 2 to 3
times the delay required to bring the temperature back to your comfort level.
• Display range:
0 to 60 °C (32 to 140 °F)
• Setting range:
5 to 40 °C (40 to 104 °F)
Exemple : If your system takes one hour to go from your saving temperature level
to your comfort temperature Ievel, it is useless to lower the temperature for a
period less than 3 hours.
• Comfort default setting:
28 °C (82 °F)
• Econo default setting:
18 °C (64 °F)
• Storage:
-20 to 50 °C (-4 to 120 °F)
a) To Program your Schedule
WARRANTY
1- Press on PGM button to access the programming mode.
2- Press on Day button to select the day to be programmed. You can select
all days of the week by pressing on Day button for 3 seconds.
3- Press on PGM button to select program 1, 2, 3 or 4.
4- Press on Hour and Min buttons to program the time.
5- When you have completed your programming, press on Mode button
to exit this function.
b) To Erase a Program :
Select the program using PGM and Day buttons, and press on Clear
button. The time field displays --:-- when the program is inactive.
c) Exemple 1 :
Comfort period from 7:00 AM to 10:30 PM
Economy period from 10:30 PM to 7:00 AM
Identical schedule for all days of the week.
1-
Press on PGM button to access the programming mode.
2-
Press on Day button 3 seconds to select every day of the week.
3-
Press on Hour button to enter 7:00 AM, Prog. 1 (
4-
Press on PGM button again to select Prog. 2 (
Hour and Min buttons to enter 10:30 PM.
5-
Press on Mode button to exit this function.
).
), and press on
AUBE TECHNOLOGIES INC. ONE (1) YEAR LIMITED WARRANTY
This product is warranted against material defects and workmanship in normal
use for a period of one year, from the date of the original purchase from authorized dealers. During this period, AUBE technologies inc. will repair or replace the
product with a new or of equivalent quality at AUBE'S option, without charge, any
product proven defective in normal use.
Warranty does not cover transportation costs. Nor does it cover a product subjected to misuse or accidental damage. This warranty does not cover the cost of
installation, removal or reinstallation.
This limited warranty is in lieu of all other warranties, obligations or liabilities
expressed or implied by the company. In no event shall AUBE technologies inc.
be liable for consequential or incidental damages resulting from installation of this
product. Some states or provinces do not allow limitations on how long an implied
warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above exclusions or limitations may not apply to you. This warranty
gives you specific legal rights and you may also have other rights which vary from
state to state.
The defective product and the original sale receipt must be returned to the original dealer or shipped pre-paid, insured and addressed to:
Aube technologies inc., 705 Montrichard, Iberville (Quebec),
Canada, J2X 5K8
If you have any questions concerning the installation or programming of this
product, please call our technical assistance at (450) 358-4600 for the Montreal
area or 1-800-831-AUBE for outside area, Monday to Friday between
8:30 AM and 5:00 PM Eastern time.
28/11/00
720-111003-A
2/2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement