Operating instructions EIZO FLEXSCAN EV2333W

Operating instructions EIZO FLEXSCAN EV2333W
You can read the recommendations in the user guide, the technical guide or the installation guide for EIZO FLEXSCAN EV2333W.
You'll find the answers to all your questions on the EIZO FLEXSCAN EV2333W in the user manual (information, specifications,
safety advice, size, accessories, etc.). Detailed instructions for use are in the User's Guide.
User manual EIZO FLEXSCAN EV2333W
User guide EIZO FLEXSCAN EV2333W
Operating instructions EIZO FLEXSCAN EV2333W
Instructions for use EIZO FLEXSCAN EV2333W
Instruction manual EIZO FLEXSCAN EV2333W
You're reading an excerpt. Click here to read official EIZO
FLEXSCAN EV2333W user guide
http://yourpdfguides.com/dref/3610229
Manual abstract:
For overview of the TCO, refer to our website. http://www.eizo.com Product specification may vary with sales areas. Confirm the specification in the manual
written in language of the region of purchase. Copyright© 2009-2010 EIZO NANAO CORPORATION All rights reserved. No part of this manual may be
reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, or otherwise, without the prior written
permission of EIZO NANAO CORPORATION. EIZO NANAO CORPORATION is under no obligation to hold any submitted material or information
confidential unless prior arrangements are made pursuant to EIZO NANAO CORPORATION's receipt of said information. Although every effort has been
made to ensure that this manual provides up-to-date information, please note that EIZO monitor specifications are subject to change without notice. Apple
and Macintosh are registered trademarks of Apple Inc.
ENERGY STAR is a U.S. registered trademark of the United States Environmental Protection Agency. Windows is a registered trademark of Microsoft
Corporation in the United States and other countries. DisplayPort icon and VESA are registered trademarks or trademarks of Video Electronics Standards
Association in the United States and other countries.
EIZO ScreenSlicer is a trademark of EIZO NANAO CORPORATION. EIZO, EIZO Logo, FlexScan and ScreenManager are registered trademarks of EIZO
NANAO CORPORATION in Japan and other countries. All other trademarks are the properties of their respective owners. Noticeforthismonitor This product
is suited to creating documents, viewing multimedia content, and other general purposes. This product has been adjusted specifically for use in the region to
which it was originally shipped.
If the product is used outside the region, it may not operate as specified in the specifications. This product may not be covered by warranty for uses other than
those described in this manual. The specifications noted in this manual are only applicable for power cords and signal cables specified by us. Use optional
products manufactured or specified by us with this product. As it takes about 30 minutes for the performance of electrical parts to stabilize, adjust the monitor
30 minutes or more after the monitor power has been turned on. In order to suppress the luminosity change by long-term use and to maintain the stable
luminosity, use of a monitor in lower brightness is recommended. When the screen image is changed after displaying the same image for extended periods of
time, an afterimage may appear. Use the screen saver or power save function to avoid displaying the same image for extended periods of time. Periodic
cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime. (Refer to "Cleaning" on the next page.
) The LCD panel is manufactured using high-precision technology. However, missing pixels or lit pixels may appear on the LCD panel, this is not
malfunction. Percentage of effective pixels : 99.9994% or higher. The backlight of the LCD panel has a fixed life span. When the screen becomes dark or
begins to flicker, please contact your dealer. Do not press on the panel or edge of the frame strongly, as this may result in the display malfunction, such as the
interference patterns, etc. If pressure is continually applied to the LCD panel, it may deteriorate or damage your LCD panel. (If the pressure marks remain on
the LCD panel, leave the monitor with a white or black screen. The symptom may disappear.
) Do not scratch or press on the panel with any sharp objects, such as a pencil or pen as this may result in damage to the panel. Do not attempt to brush with
tissues as this may scratch the LCD panel. When the monitor is cold and brought into a room or the room temperature goes up quickly, dew condensation may
occur inside and outside the monitor. In that case, do not turn the monitor on and wait until dew condensation disappears, otherwise it may cause some
damages to the monitor. Cleaning Attention · Never use any solvents or chemicals, such as thinner, benzene, wax, alcohol, and abrasive cleaner, which may
damage the cabinet or LCD panel.
NOTE · Optional ScreenCleaner is recommended for cleaning the panel surface. [LCDPanel] · Clean the LCD panel with a soft cloth such as cotton cloth or
lens cleaning paper. · Remove persistent stains gently with a cloth dampened with a little water, and then clean the LCD panel again with a dry cloth for
better finishing. [Cabinet] Clean the cabinet with a soft cloth dampened with a little mild detergent. Tousethemonitorcomfortably · An excessively dark or
bright screen may affect your eyes.
Adjust the brightness of the monitor according to the environmental conditions. · Staring at the monitor for a long time tires your eyes. Take a 10-minute rest
every hour. CONTENTS Cover .......
..........
.....
.....
..........
..........
.....
.....
... 1 . -8 Turningoffthemonitorautomatically [OffTimer]......
..........
.....
.....
..........
..........
.....
... -9 SettingOn/Offfortheautomaticbrightness adjustmentfunction[AutoEcoView]..
......... -10 Shiftingtothepowersavingmodewhena personleavesthemonitor [EcoViewSense].
..........
.....
.....
..........
..........
... To set EcoView Sense On/Off ..
.....
..........
......... 25 To change the detection level .
.....
.....
..........
...... 25 -11 SettingOn/Offforthepowersavinglevel indicator[EcoViewIndex]....
.....
.....
..........
..... 6 -1 ScreenSizeSelection.....
.....
.....
..........
..........
6 . To change screen size [Screen Size] ....
.....
...... 26 To adjust brightness of non-display area [Border Intensity] ....
..........
.....
.....
..........
..........
.. 27 -1 SettingAdjustmentMenuDisplay ...
.....
....... 7 . To update menu settings [Menu Size/Menu Position/Menu Off Timer/ Translucent] ..
..........
.....
.....
..........
..........
.....
.....
.. 27 -1 SettingOrientation........
..........
.....
.....
..........
.. 8 To set the orientation of the Adjustment menu [Orientation] ........
.....
.....
..........
..........
.....
.....
...... 28 - ColorAdjustment ....
..........
.....
.....
..........
........ 19 . To select the display mode (FineContrast mode) .
.....
.....
..........
..........
.....
.... 19 To perform advanced adjustments .
..........
........ 20 Adjustment items in each mode ..
.....
.....
..........
. 20 To adjust the brightness [Brightness] .........
.....
. 20 To adjust the contrast [Contrast]....
..........
......... 21 To adjust the color temperature [Temperature] .
.....
.....
..........
..........
.....
.....
..........
21 To adjust the gamma value [Gamma]..........
.....
21 To adjust the color saturation [Saturation] .....
... 22 To adjust the hue [Hue] .......
..........
.....
.....
......... 22 To adjust the gain value [Gain] .
..........
.....
.....
.... 22 To set the Overdrive intensity [Overdrive] ......
.. 22 - AdjustingVolume[Volume]........
.....
.....
........ - SwitchingsoundsourceduringDisplayPort signalinput[Source]..
..........
.....
.....
..........
..... -6 TurningofftheaudiooutputatPowerSaving mode[PowerSave].....
.....
.....
..........
..........
.... .
-7 SettingOn/OffforPowerSavingmode [PowerSave].....
..........
..........
.....
.....
..........
..... -17 Enabling/DisablingDDC/CI communication.....
.....
.....
..........
..........
.....
.....
. 9 -18 SettingPowerIndicatorON/OFF [PowerIndicator].........
..........
.....
.....
..........
... 9 -19 SettingLanguage[Language].......
.....
.....
..... 9 -0 SettingEIZOlogodisplayON/OFF.....
......... 0 .
-1 ResumingtheDefaultSetting[Reset].....
.... 0 To reset color adjustment values .
..........
..........
. 30 To reset all adjustments to the factory default settings ....
.....
..........
..........
.....
.....
..........
..........
.. 30 -1 LockingButtons...
.....
..........
..........
.....
.....
...... 8 -16 DisplayingMonitorInformation [Information]....
..........
.....
.....
..........
..........
.....
. 9 . Noticeforthismonitor...
..........
..........
.....
.....
..........
... CONTENTS .......
.....
.....
..........
..........
.....
.....
..........
... . Chapter1 FeaturesandOverview......
.....
.....
..... 7 1-1 Features .....
..........
.....
.....
..........
..........
.....
.....
.... 7 . 1- ControlsandFunctions.....
..........
.....
.....
......... 9 1- CompatibleResolutions/Frequencies.
........ 10 1- FunctionsandBasicOperation..
.....
.....
........11 . Chapter SettingsandAdjustments.
..........
... 1 -1 UtilityDisk..
.....
..........
..........
.....
.....
..........
....... 1 Disk contents and software overview ...
.....
.....
.. 15 To use "ScreenManager Pro for LCD (DDC/CI)/ EIZO ScreenSlicer" ........
..........
.....
.....
..........
.... 15 - ScreenAdjustment.
You're reading an excerpt. Click here to read official EIZO
FLEXSCAN EV2333W user guide
http://yourpdfguides.com/dref/3610229
.....
.....
.....
..........
..........
.... 16 DigitalInput .
.....
..........
..........
.....
.....
..........
..........
. 16 . AnalogInput...
.....
..........
..........
.....
.....
..........
........ 16 Chapter ConnectingCables..
.....
.....
..........
.... 1 -1 ConnectingMorethanTwoPCstothe Monitor......
.....
.....
..........
..........
.....
.....
..........
... 1 . To switch the input signal ......
.....
.....
..........
....... 32 To set input signal selection [Input Signal] ...
.... 32 CONTENTS CONTENTS Chapter Troubleshooting.
.....
..........
..........
.... .
Chapter Reference.....
..........
..........
.....
.....
...... 6 -1 HowtoAttachtheOptionalArm ....
..........
.... 6 .
- AttachingtheFlexStand.....
..........
..........
.....
. 8 . - AttachingtheTriStand...
..........
..........
.....
.....
. 9 - FoldingtheTriStand.........
..........
.....
.....
......... 0 5-5 Specifications.
..........
.....
.....
..........
..........
.....
.. -6 Glossary...
..........
..........
.....
.....
..........
..........
.... 8 -7 PresetTiming.
.....
..........
..........
.....
.....
..........
... 0 FCCDeclarationofConformity.......
.....
.....
......... 1 HinweisezurAuswahldesrichtigen SchwenkarmsfürIhrenMonitor.
..........
.....
.....
... . HinweiszurErgonomie ......
..........
.....
.....
..........
.. . 6 CONTENTS Chapter1 FeaturesandOverview Thank you very much for choosing an EIZO color LCD monitor. 1-1 Features · 23" wide format LCD ·
Applicable to the resolution of 1920 × 1080 · Power saving function Suppressing the power consumption*1 reduces the carbon dioxide emissions. This
product is equipped with various power saving functions. Power Consumption when main power switch is Off: 0W Equipped with main power switch.
Turning off the main power switch completely shuts off power supply to the monitor while the monitor is not used. Standby power: 0.1W or less Standby
power when Power button is Off: 0.
1W or less. LED backlight LCD panel (EV2313W only) The LED backlight provides better power efficiency and reduced power consumption*1 compared to
existing fluorescent backlight LCD panels. No mercury, a hazardous substance, is used. Auto EcoView function The sensor on the front side of the monitor
detects the environmental brightness to adjust the screen brightness automatically and comfortably. Excessively high brightness may lead a damage to the
natural environment as well as to your eyes.
Suppressing the excessively high brightness will be helpful to reduce the power consumption and the damage to your eyes. 2-9 "Setting On/Off for the
automatic brightness adjustment function [Auto EcoView]" (page 24) EcoView Sense function The sensor on the front side of the monitor detects the
movement of a person. When a person moves away from the monitor, it shifts to the power saving mode automatically and does not display the images on the
screen. Therefore, the function reduces the power consumption. 2-10 "Shifting to the power saving mode when a person leaves the monitor [EcoView Sense]"
(page 25) EcoView Index function The green indicator shows the power consumption ratio responding to the brightness of the monitor.
You can realize the power consumption reduction by taking consideration in the ratio of power saving. 2-11 "Setting On/Off for the power saving level
indicator [EcoView Index]" (page 26) · Brightness stabilization through dimming control Supports brightness adjustments over a wide range (EV2313W:
2-100%, EV2333W: 20-100%). tor Connects the stereo mini jack cable. Complies with Kensington's MicroSaver security system. Used to adjust the height
and angle of the monitor screen. Covers the monitor cables. Outputs audio source. Connects the headphones. * ScreenManager ® is an EIZO's nickname of
the Adjustment menu. See page 11 for how to use.
Chapter 1 Features and Overview 9 1- CompatibleResolutions/Frequencies The monitor supports the following resolutions. AnalogInput(D-Sub) Resolution
640 × 480 (VGA, VESA) 720 × 400 (VGA TEXT) 800 × 600 (VESA) 1024 × 768 (VESA) 1152 × 864 (VESA) 1280 × 960 (VESA) 1280 × 1024 (VESA) 1280
× 720 (CEA-861) 1680 × 1050 (VESA CVT, VESA CVT RB) * 1920 × 1080 (CEA-861) Frequency ~75 Hz 70 Hz ~75 Hz ~75 Hz 75 Hz 60 Hz ~75 Hz 60 Hz
60 Hz 60 Hz 148.5 MHz (Max.) DotClock DigitalInput(DVI-D) Resolution 640 × 480 (VGA) 720 × 400 (VGA TEXT) 800 × 600 (VESA) 1024 × 768 (VESA)
1280 × 960 (VESA) 1280 × 1024 (VESA) 1280 × 720 (CEA-861) 1680 × 1050 (VESA CVT, VESA CVT RB) * 1920 × 1080 (CEA-861) Frequency 60 Hz 70
Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 148.5 MHz (Max.) DotClock DigitalInput(DisplayPort) Resolution 640 × 480 (VGA, CEA) 720 × 400 (VGA
TEXT) 720 × 480 (4:3) (CEA) 720 × 480 (16:9) (CEA) 800 × 600 (VESA) 1024 × 768 (VESA) 1280 × 960 (VESA) 1280 × 1024 (VESA) 1280 × 720
(CEA-861, CEA) 1680 × 1050 (VESA CVT, VESA CVT RB) * 1920 × 1080 (CEA-861) Frequency 60 Hz 70 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz
60 Hz 60 Hz 148.5 MHz (Max.) DotClock A graphics board in conformance with VESA standard and CEA-861 standard is required. * Recommended
resolution (Set this resolution) 10 Chapter 1 Features and Overview 1- FunctionsandBasicOperation Toadjustthescreenandcolor
Mainmenu(Refertopage1foroperation) Analoginputonly [Atanalogsignalinput] 1 ScreenAdjustment (AutomaticAdjustment) Page16 [Atdigitalsignalinput] To
adjust flickering and position [Screen] ..
.....
.....
..........
..........
.... see page 16 To adjust color gradation automatically [Range] .
.....
..........
..........
.....
.....
see page 18 ScreenAdjustment (AdvancedAdjustment) Page17 [Atanalogsignalinput] · The Adjustment menu and the FineContrast mode name cannot be
displayed at the same time. FineContrastmode Page19 ColorAdjustment SimpleAdjustment[FineContrastmode] [Atdigitalsignalinput] This function allows
easy selection of a desired mode from five modes according to monitor application. To eliminate vertical bars [Clock*] ... see page 17 To remove flickering or
blurring [Phase*].....
..........
.....
.....
..........
. see page 17 To correct screen position [Position*] .........
.....
.....
..........
.... see page 18 To modify blurred characters/lines [Smoothing] ......
.....
.....
..........
.... see page 18 * Items marked with * can be adjusted with analog input. Brightnessandvolumedirectmenu ColorAdjustment AdvancedAdjustment Page0
BrightnessandVolumeAdjustment Press or to display the adjustment menu. Brightness: Press Volume : Press or or . . "Brightness", "Contrast",
"Temperature", "Gamma", "Saturation", "Hue", "Gain" and "Overdrive" can be set for each mode (Custom/ sRGB/Text/Picture/Movie). Settable functions
vary with the FineContrast mode.
Resumingthedefaultsettings To reset color adjustment values [Reset] .....
.....
..........
..........
.....
. see page 30 Chapter 1 Features and Overview 11 Tousethemonitorwithlowpowerconsumption Mainmenu(Refertopage1foroperation) [Atanalogsignalinput]
Power-saveSettings [Atdigitalsignalinput] Setting On/Off for Power Saving mode [Power Save] ....
..........
..........
...see page 23 Turning off the monitor automatically [Off Timer] ..
.....
..........
..........
...see page 24 Shifting to the power saving mode when a person leaves the monitor [EcoView Sense] ..
.....
..........
.......see page 25 · The Adjustment menu and the EcoView menu cannot be displayed at the same time. · EcoView menu is temporarily displayed when the
power of the monitor is turned on. EcoViewmenu SettingOn/OfffortheEcoView function (powersavingfunction) Page This monitor is equipped with the
EcoView function for power saving.
You're reading an excerpt. Click here to read official EIZO
FLEXSCAN EV2333W user guide
http://yourpdfguides.com/dref/3610229
Press to display the setting menu. Choose the item with or (you can also choose it or . with ). Change "On" and "Off" with Setting On/Off for the automatic
brightness adjustment function [Auto EcoView] ..
.....
..........
..........
...see page 24 Shifting to the power saving mode when a person leaves the monitor [EcoView Sense] ..
.....
..........
..........
see page 25 Setting On/Off for the power saving level indicator [EcoView Index] .....
.....
..........
..........
see page 26 1 Chapter 1 Features and Overview Tomakeusefulsettings/adjustments Adjustmentmenu(Refertopage1foroperation) [Atanalogsignalinput]
OtherSettings [Atdigitalsignalinput] To change screen size [Screen Size] .....
.....
..........
....... see page 26 To adjust brightness of non-display area [Border Intensity] ...
.....
.....
..........
. see page 27 To set input signal selection [Input Signal] .........
.....
.....
........ see page 32 To update menu settings [Menu Size/Menu Position/Menu Off Timer/ Translucent] ..
..........
.....
.....
........ see page 27 To set the orientation of the Adjustment menu [Orientation] ..
..........
.....
.....
........ see page 28 Setting Power Indicator ON/OFF [Power Indicator] ..
..........
.....
.....
.. see page 29 To reset all adjustments to the factory default settings [Reset] ........
..........
.....
. see page 30 Page9 Information SoundSettings [AtD-Sub/DVI-Dsignalinput] [AtDisplayPortsignalinput] Displaying Monitor Information [Information]
Adjusting Volume [Volume]....
........ see page 23 Switching sound source during DisplayPort signal input [Source*] ..
..........
.....
. see page 23 Turning off the audio output at Power Saving mode [Power Save] ....
..........
....... see page 23 * Language Page9 An item marked with * can be adjusted with DisplayPort input. Setting Language [Language] Locking Buttons ..
.....
.....
..........
..... see page 28 Enabling/Disabling DDC/CI communication .....
.....
.....
..........
..........
.....
.....
... see page 29 Setting EIZO logo display ON/OFF ... see page 30 Chapter 1 Features and Overview 1 BasicoperationofAdjustmentmenu
[DisplayingAdjustmentmenuandselectingfunction] . The Main menu appears. (1) Press (2) Select a function with / / / , and press . The Sub menu appears.
(3) Select a function with / / / , and press . The adjustment/setting menu appears. (4) Adjust the selected item with / / / , and press . The setting is saved.
[ExitingAdjustmentmenu] (1) Choose <Return> from the Sub menu and press (2) Choose <Exit> from the Main menu and press NOTE . The Main menu
appears. . The Adjustment menu quits. twice quickly. twice in the Main menu or Sub menu.
· The Adjustment menu can also be exited by pressing · <Exit> or <Return> can also be selected by pressing 1 Chapter 1 Features and Overview Chapter
SettingsandAdjustments -1 UtilityDisk An "EIZO LCD Utility Disk" (CD-ROM) is supplied with the monitor. The following table shows the disk contents and
the overview of the software programs. Diskcontentsandsoftwareoverview The disk includes software programs for adjustment, and User's Manual. Refer to
"Readme.txt" file on the disk for software startup procedures or file access procedures.
Item A "Readme.txt" file Screen adjustment pattern files ScreenManager Pro for LCD (DDC/CI) EIZO ScreenSlicer Used when adjusting the image of the
analog signal input manually. A software for adjusting the screen using the mouse and keyboard. A software that divides a screen and lays out multiple
windows efficiently. Overview Windows Macintosh - - User's Manual of this monitor (PDF file)
Touse"ScreenManagerProforLCD(DDC/CI)/EIZOScreenSlicer" For the installation and use of "ScreenManager Pro for LCD (DDC/CI)/ EIZO SceenSlicer",
refer to the respective User's Manual on the disk.
Chapter 2 Settings and Adjustments 1 - ScreenAdjustment DigitalInput When digital signals are input, images are displayed correctly based on the preset data
of the monitor, but if characters and/or lines appear blurred, go to step 6 "To modify blurred characters/lines [Smoothing]". When performing more advanced
adjustment, see "2-3 Color Adjustment" (page 19) and subsequent pages. AnalogInput The monitor screen adjustment is used to suppress flickering of the
screen or adjust screen position and screen size correctly according to the PC to be used. The Self Adjust function works when all of the following conditions
are satisfied: · When a signal is input into the monitor for the first time · When the resolution or Vertical/Horizontal Frequency not displayed before is set If
the screen is not displayed correctly even after performing the Self Adjust operation, adjust the screen according to the procedures on the following pages to
use the monitor comfortably. [AdjustmentProcedure] Attention 1 Performtheautoadjustment. Toadjustflickering,screenposition,andscreensize
automatically[Screen] (1) Choose <Screen> from the <Auto Adjustment> menu, and press . The <Auto Adjustment> menu appears. · Wait 30 minutes or
more from monitor power on before starting adjustments. It is recommended to turn off the EcoView Sense to prevent the monitor from shifting to the power
saving mode in this period (Refer to "2-10 Shifting to the power saving mode when a person leaves the monitor [EcoView Sense]" on page 25). · The Self
Adjust function does not work for the images under the resolution of 800 × 600 (SVGA).
· The self adjustment (or automatic screen adjustment) function works correctly when an image is fully displayed over the Windows or Macintosh display
area. They do not work properly in the cases below: - When an image is displayed only on a part of the screen (command prompt window, for example) When a black background (wallpaper, etc.) is in use Also, these functions cannot work properly in some graphic boards. (2) Choose "Execute" with or , and
press . Flickering, screen position, and screen size are corrected by the autoadjustment function. If the screen is not displayed correctly even after adjusting in
step 1 above, perform the adjustments according to the procedures on the following pages. When the screen is displayed correctly, go to step 5 "To adjust
color gradation automatically [Range]". 2 Preparethedisplaypatternfortheanalogdisplayadjustment. Load the "EIZO LCD Utility Disk" to your PC, and then
open the "Screen adjustment pattern files". NOTE · For details and instructions on opening the "Screen adjustment pattern files", refer to the "Readme.
txt" file. 16 Chapter 2 Settings and Adjustments 3 Performtheautoadjustmentagainwiththeanalogscreen adjustmentpatterndisplayed.
Toadjustflickering,screenposition,andscreensize automatically[Screen] (1) Display Pattern 1 of the "Screen adjustment pattern files" in full screen on the
monitor. (2) Choose <Screen> from the <Auto Adjustment> menu, and press . The <Auto Adjustment> menu appears.
(3) Choose "Execute" with or , and press . Flickering, screen position, and screen size are corrected by the autoadjustment function.
You're reading an excerpt. Click here to read official EIZO
FLEXSCAN EV2333W user guide
http://yourpdfguides.com/dref/3610229
If the screen is not displayed correctly even after adjusting in step 3 above, perform the adjustments according to the procedures on the following pages.
When the screen is displayed correctly, go to step 5 "To adjust color gradation automatically [Range]". 4
Performadvancedadjustmentsforthefollowingusingthe <Screen>menuoftheAdjustmentmenu.
Adjust the clock, phase and position, in this order. Toeliminateverticalbars[Clock] (1) Choose <Clock> from the <Screen> menu, and press The <Clock>
menu appears. NOTE . (2) Adjust the clock with or , and press . The adjustment is completed. · Press the control button slowly so as not to miss the adjustment
point. · When blurring, flickering or bars appear on the screen after adjustment, proceed to [Phase] to remove flickering or blurring.
Toremoveflickeringorblurring[Phase] Adjustable range: 0 to 63 (1) Choose <Phase> from the <Screen> menu, and press The <Phase> menu appears.
Attention . · Flickering or blurring may not be eliminated depending on your PC or graphics board.
(2) Adjust the phase with or , and press . NOTE The adjustment is completed. · When vertical bars appear on the screen after adjustment, go back to "To
eliminate vertical bars [Clock]". (Clock Phase Position) Chapter 2 Settings and Adjustments 17 Tocorrectscreenposition[Position] (1) Choose <Position>
from the <Screen> menu, and press The <Position> menu appears. NOTE . (2) Adjust the position with / / / to display the image properly in the display area
of the monitor, and press The adjustment is completed. · Since the number of pixels and the pixel positions are fixed on the LCD monitor, only one position is
provided to display images correctly. The position adjustment is made to shift an image to the correct position. 5 Adjustthecolorgradation.
Toadjustcolorgradationautomatically[Range] Every color gradation (0 to 255) can be displayed by adjusting the signal output level.
(1) Display Pattern 2 in full screen on the monitor using the "Screen adjustment pattern files". (2) Choose <Range> from the <Auto Adjustment> menu, and
press . (3) Choose "Execute" with or , and press . The output range is adjusted automatically. (4) Close the Pattern 2.
6 Modifyblurredcharactersorlines. Tomodifyblurredcharacters/lines[Smoothing] When a image is displayed with a resolution other than the recommendation,
the characters or lines of the displayed image may be blurred. Adjustable range: 1 to 5 (1) Choose <Screen> from the Adjustment menu, and press . (2)
Choose <Smoothing> from the <Screen> menu, and press . The <Smoothing> menu appears.
Attention · Smoothing setting may not be required depending on the display resolution. (You cannot choose the smoothing icon.) (3) Adjust the
characters/lines with The adjustment is completed. or , and press . 18 Chapter 2 Settings and Adjustments - ColorAdjustment
Toselectthedisplaymode(FineContrastmode) FineContrast allows you to select the best display mode easily according to the monitor's application.
FineContrast mode Mode Custom sRGB Text Picture Movie Purpose Available to change all setting values. Suitable for color matching with sRGB
compatible peripherals. Suitable for displaying texts for word processing or spreadsheets. Suitable for displaying images such as photos or picture images.
Suitable for playing back animated images.
Displays the current mode. (1) Press or . or while mode name is displayed. NOTE The FineContrast mode name appears at the lower left of the screen. (2)
Change the mode by pressing CustomsRGBTextPictureMovie · The Adjustment menu and the FineContrast mode name cannot be displayed at the same time. ·
"ScreenManager Pro for LCD (DDC/CI)" allows you to select the FineContrast mode automatically according to the application used. (Refer to "Chapter 3
Auto FineContrast" on the User's Manual for "ScreenManager Pro for LCD (DDC/CI)".) Chapter 2 Settings and Adjustments 19
Toperformadvancedadjustments Independent setting and saving of color adjustment are available for each FineContrast mode. Attention
Adjustmentitemsineachmode According to the FineContrast mode selected, the adjustable function differs. : Adjustment available -: Invalid for adjustment
Icon Function Brightness Contrast Temperature Gamma Saturation Hue Gain Overdrive Reset FineContrastmode Custom sRGB Text Picture Movie - - - - - - - - - - - - - - · Wait 30 minutes or more from monitor power on before starting adjustments.
It is recommended to turn off the EcoView Sense to prevent the monitor from shifting to the power saving mode in this period (Refer to "2-10 Shifting to the
power saving mode when a person leaves the monitor [EcoView Sense]" on page 25). · Perform the range adjustment first when adjusting color for analog
input signals. (Refer to "To adjust color gradation automatically" on page 18). · The same image may be seen in different colors on multiple monitors due to
their monitor-specific characteristics. Make fine color adjustment visually when matching colors on multiple monitors.
NOTE · The values shown in "%" or "K" are available only as reference. · Using the "ScreenManager Pro for LCD (DDC/CI)" allows you to perform the
color adjustment by using the mouse and keyboard of your PC. The adjusted status can be registered as a color data and restore the data later. (Refer to
"Chapter 4 Color Adjustment" on the User's Manual for "ScreenManager Pro for LCD (DDC/CI)".) NOTE Toadjustthebrightness[Brightness] The screen
brightness is adjusted by changing the brightness of the backlight (Light source from the LCD back panel).
Adjustable range: 0 to 100% . (1) Choose <Color> from the Adjustment menu, and press (2) Choose <Brightness> from the <Color> menu, and press . The
<Brightness> adjustment menu appears. · You can also adjust the brightness by using the direct menu (Refer to "1-4 Functions and Basic Operation" on page
11). (3) Adjust the brightness with The adjustment is completed. or , and press . 0 Chapter 2 Settings and Adjustments Toadjustthecontrast[Contrast] The
luminance of the screen is adjusted by varying the video signal level. Adjustable range: 0 to 100% (1) Choose <Color> from the Adjustment menu, and press
(2) Choose <Contrast> from the <Color> menu, and press The <Contrast> adjustment menu appears. NOTE . .
(3) Adjust the contrast with The adjustment is completed. or , and press . · In the contrast of 50%, every color gradation is displayed.
You're reading an excerpt. Click here to read official EIZO
FLEXSCAN EV2333W user guide
http://yourpdfguides.com/dref/3610229
· When adjusting the monitor, it is recommended to perform the brightness adjustment which may not lose the gradation characteristics, prior to the contrast
adjustment. Perform the contrast adjustment in the following cases. When you feel the image is dark even if the brightness is set to 100%. (Set the contrast to
higher than 50%). When you feel the image is bright even if the brightness is set to 0%. (Set the contrast to lower than 50%).
Toadjustthecolortemperature[Temperature] The color temperature can be adjusted.
The color temperature is normally used to express the hue of "White" and/or "Black" by a numerical value. The value is expressed in degrees "K" (Kelvin). In
the same way as the flame temperature, the image on the monitor is displayed reddish if the color temperature is low and is bluish if the color temperature is
high. The gain preset values are set for each color temperature setting value. 5000K 6500K The white color image is displayed reddish.
The 5000K or 6000K is usually used in the printing industry. The white color image is displayed in warm white like paper white. The temperature is suitable
to display photographs or video images. The white color image is displayed slightly bluish white. NOTE 9300K · You cannot adjust the value if the icon is not
displayed, depending on the FineContrast mode selected.
(See "Adjustment items in each mode" on page 20.) · [Gain] allows you to perform more advanced adjustment (See "To adjust the gain value" on page 22). · If
you set to [Off], the image is displayed in the preset color of the monitor (Gain: 100% for each RGB). · When changing the gain value, the color temperature
adjusting range is changed to "Off". Adjustable range: Off, 4000K-10000K (specified by every 500K unit, including 9300K) (1) Choose <Color> from the
Adjustment menu, and press . (2) Choose <Temperature> from the <Color> menu, and press The <Temperature> adjustment menu appears. . (3) Adjust the
color temperature with The adjustment is completed. or , and press . Toadjustthegammavalue[Gamma] The gamma value can be adjusted.
The luminance of the monitor varies depending on the input signal, however, the variation rate is not proportional to the input signal. To keep the balance
between the input signal and the luminance of the monitor is called as "Gamma correction". Adjustable range: 1.8, 2.0, 2.2 (1) Choose <Color> from the
Adjustment menu, and press (2) Choose <Gamma> from the <Color> menu, and press The <Gamma> adjustment menu appears. NOTE · You cannot adjust
the value if the icon is not displayed, depending on the FineContrast mode selected. (See "Adjustment items in each mode" on page 20.) . .
(3) Adjust the gamma value with The adjustment is completed. or , and press . Chapter 2 Settings and Adjustments 1 Toadjustthecolorsaturation[Saturation]
This function allows you to adjust the saturation of the color on the monitor. Adjustable range: -128 to 127 (1) Choose <Color> from the Adjustment menu,
and press . (2) Choose <Saturation> from the <Color> menu, and press .
The <Saturation> adjustment menu appears. Attention · This function does not enable to display every color gradation. NOTE (3) Adjust the saturation of the
color with The adjustment is completed. or , and press . · You cannot adjust the value if the icon is not displayed, depending on the FineContrast mode
selected.
(See "Adjustment items in each mode" on page 20.) · Setting the minimum (-128) turns the image to a monochrome screen. Attention Toadjustthehue[Hue]
This function allows you to adjust the hue. If you set the hue to a high value, the image turns greenish. If low, the image turns purplish. Adjustable range: -32
to 32 (1) Choose <Color> from the Adjustment menu, and press (2) Choose <Hue> from the <Color> menu, and press . The <Hue> adjustment menu
appears. · This function does not enable to display every color gradation. NOTE . (3) Adjust the hue with or , and press .
· You cannot adjust the value if the icon is not displayed, depending on the FineContrast mode selected. (See "Adjustment items in each mode" on page 20.)
The adjustment is completed. Toadjustthegainvalue[Gain] Each luminance of red/green/blue composing the color is called "Gain". The gain adjustment may
change the color tone of the "White". Adjustable range: 0 to 100% (1) Choose <Color> from the Adjustment menu, and press (2) Choose <Gain> from the
<Color> menu, and press . The <Gain> adjustment menu appears. Attention · This function does not enable to display every color gradation. NOTE . (3)
Adjust the respective value of Red, Green or Blue with .
The adjustment is completed. or , and press · You cannot adjust the value if the icon is not displayed, depending on the FineContrast mode selected. (See
"Adjustment items in each mode" on page 20.) · The gain value may change depending on the value of the color temperature. · When changing the gain value,
the color temperature adjusting range is changed to "Off".
Attention TosettheOverdriveintensity[Overdrive] This function allows you to set the overdrive intensity based on the use of the monitor. Image lag sensation is
reduced if [Enhanced] is set when displaying animated images. Adjustment range: Enhanced, Standard, Off (1) Choose <Color> from the Adjustment menu,
and press (2) Choose <Overdrive> from the <Color> menu, and press The <Overdrive> setting menu appears. . .
, and press . · Overdrive function is disabled in the following case: Vertical frequency of input signal is not 60Hz. @@@@@@@@@@You can select the
DisplayPort or Stereo Mini Jack. (1) Choose <Sound> from the Adjustment menu, and press . @@(1) Choose <Sound> from the Adjustment menu, and press
. @@@@(1) Choose <PowerManager> from the Adjustment menu, and press . @@@@@@@@@@@@@@@@@@@@@@@@@@@@If the
monitor does not shift to the power saving mode as you intended, change the detection level according to the following procedure. Adjustable range: see
below list Level Detectable Range Details The detectable range is defined by the Auto Automatic setting person's movement. When you get out (default
setting) (120 cm or less) of the range, the monitor shifts to the power saving mode. Since the function determines whether the object is moving Automatic
setting or not, the monitor can shift to the power Manual1 saving mode even if there is a chair or wall (90 cm or less) in the detectable range.
Manual2 120 cm or less When you get out of the detectable range, the monitor shifts to the power saving mode.
You're reading an excerpt. Click here to read official EIZO
FLEXSCAN EV2333W user guide
http://yourpdfguides.com/dref/3610229
This setting is recommended if the monitor frequently shifts to the power saving mode when the level is "Auto" or "Manual1" even though you are in front of
the monitor. Manual3 90 cm or less (1) Choose <PowerManager> from the Adjustment menu, and press . (2) Choose <EcoView Sense> from the
<PowerManager> menu, and press The <EcoView Sense> setting menu appears. . (3) Select "Auto" or "Manual" with or . When selecting "Manual", select
1, 2 or 3 for the detection level of the sensor with or . (4) Press . The setting is completed. Chapter 2 Settings and Adjustments -11
SettingOn/Offforthepowersaving levelindicator[EcoViewIndex] By using the EcoView Index function, the indicator that shows the level of power saving
appears at the time of turning on the monitor, adjusting the brightness or switching the FineContrast mode.
The power saving ratio comes to high as the indicator level meter lights towards right. (1) Press The <EcoView> setting menu appears. . (2) Choose
"EcoView Index" with (3) Select "On" or "Off" with or The setting is completed. or .
(You can also choose it with , and press . .) -1 ScreenSizeSelection Attention Tochangescreensize[ScreenSize] The image with the resolution other than the
recommended resolution is displayed in full screen automatically. You can change the screen size by using <Screen Size> from <Others> menu. Setting Full
Screen (default setting) Enlarged Normal Function Displays an image in full screen.
Images are distorted in some cases because the vertical rate is not equal to the horizontal rate. Displays an image in full screen. In some cases, a blank
horizontal or vertical border appears to equalize the vertical rate and the horizontal rate. Displays images with the specified resolution. Full Screen (Default
setting) · Selecting [Enlarged] or [Normal] does not enable to display every color gradation. Example: Image size 1024 × 768 Enlarged Normal (1920 ×
1080) (1440 × 1080) (1024 × 768) (1) Choose <Others> from the Adjustment menu, and press . (2) Choose <Screen Size> from the <Others> menu, and
press . The screen size setting window appears. (3) Select "Full Screen," "Enlarged," or "Normal" with press . The screen size setting is completed.
or , and 6 Chapter 2 Settings and Adjustments Toadjustbrightnessofnon-displayarea[BorderIntensity] A border (black area with no image) around the image
appears in the "Normal" or "Enlarged" mode. Border (1) Choose <Others> from the Adjustment menu, and press . (2) Choose <Border Intensity> from the
<Others> menu, and press The <Border Intensity> menu appears. . (3) Adjust border intensity with or , and press . The border intensity adjustment is
completed. -1 SettingAdjustmentMenuDisplay Toupdatemenusettings[MenuSize/MenuPosition/Menu OffTimer/Translucent] MenuSize Change the Adjustment
menu size using the following procedure. (1) Choose <Others> from the Adjustment menu, and press . (2) Choose <Menu Settings> from the <Others>
menu, and press . (3) Choose <Menu Size> from the <Menu Settings> menu, and press The <Menu Size> menu appears.
. (4) Select "Normal" or "Enlarged" with The setting is completed. or , and press . MenuPosition Adjust the menu position using the following procedure. (1)
Choose <Others> from the Adjustment menu, and press .
(2) Choose <Menu Settings> from the <Others> menu, and press . (3) Choose <Menu Position> from the <Menu Settings> menu, and press The <Menu
Position> menu appears. . (4) Select a menu position with The setting is completed. or , and press .
Chapter 2 Settings and Adjustments 7 MenuOffTimer Set the menu display time using the following procedure. Adjustment range: Disable, Enable (15, 30, 45,
60s) (1) Choose <Others> from the Adjustment menu, and press . (2) Choose <Menu Settings> from the <Others> menu, and press . (3) Choose <Menu Off
Timer> from the <Menu Settings> menu, and press The <Menu Off Timer> menu appears. NOTE · The display time of the FineContrast mode, EcoView
menu and EcoView Index remains unchanged. . (4) Select "Enable" or "Disable" with or . When selecting "Enable", choose a time for displaying menu with .
(5) Press . The setting is completed.
or Translucent Set the transparency for menu display using the following procedure. (1) Choose <Others> from the Adjustment menu, and press . (2) Choose
<Menu Settings> from the <Others> menu, and press . (3) Choose <Translucent> from the <Menu Settings> menu, and press The <Translucent> menu
appears. . . (4) Adjust the transparency for menu display with The setting is completed. or , and press -1 SettingOrientation NOTE
TosettheorientationoftheAdjustmentmenu[Orientation] This function allows you to change the orientation of the Adjustment menu when using the monitor
screen in vertical display position. (1) Choose <Others> from the Adjustment menu, and press (2) Choose <Orientation> from the Others menu, and press
The <Orientation> menu appears. .
. . · For using the monitor with "Portrait" position, the graphics board supporting portrait display is required. When placing the monitor in a "Portrait"
position, settings of your graphics board need to be changed. Refer to the manual of the graphics board for details.
Attention (3) Select "Landscape" or "Portrait" with The setting is completed. or , and press (4) When selecting "Portrait", turn the monitor screen 90° in
clockwise direction. · Be sure that the cables are correctly connected. -1 LockingButtons This function allows you to lock (1) Press (2) Press to prevent
changing the adjusted/set status. to turn off the monitor.
holding down to turn on the monitor. The Lock/Unlock setting is toggled by performing the operation in step 2. 8 Chapter 2 Settings and Adjustments -16
DisplayingMonitorInformation [Information] This function allows you to display the input signal status, current resolution and model name. Information 1/3 :
Input signal status, resolution and H/V frequency Information 2/3 : Enable/Disable setting for DDC/CI Information 3/3 : Model name, serial number and
usage time (1) Choose <Information> from the Adjustment menu, and press . The <Information> menu appears. NOTE · The usage time is not always "0"
when you purchase the monitor due to factory inspection. (2) Then, press to check settings, etc. NOTE -17 Enabling/DisablingDDC/CI communication This
function allows you to enable/disable the DDC/CI communication.
You're reading an excerpt. Click here to read official EIZO
FLEXSCAN EV2333W user guide
http://yourpdfguides.com/dref/3610229
(1) Press to turn off the monitor. (2) Press holding down to turn on the monitor.
The Enable/Disable setting is toggled by performing the operation in step 2. · You can check the DDC/CI setting in the <Information> menu. -18
SettingPowerIndicatorON/OFF [PowerIndicator] This function allows you to set the power indicator (blue) ON/OFF in the monitor ON condition. (1)
Choose <Others> from the Adjustment menu, and press . (2) Choose <Power Indicator> from the <Others> menu, and press . The <Power Indicator> menu
appears. (3) Select "Enable" or "Disable" with The setting is completed. or , and press . -19 SettingLanguage[Language] This function allows you to select a
language for the adjustment menu or displaying message. Selectablelanguages English/German/French/Spanish/Italian/Swedish/Simplified Chinese/
Traditional Chinese/Japanese (1) Choose <Language> menu from the Adjustment menu, and press The <Language> menu appears.
. (2) Choose a language with The setting is completed. / / / , and press . Chapter 2 Settings and Adjustments 9 -0 SettingEIZOlogodisplayON/OFF The EIZO
logo appears on the display when turning on the monitor. This function allows you to display, or not, the EIZO logo.
(1) Press (2) Press to turn off the monitor. holding down to turn on the monitor. The EIZO logo display setting is toggled by performing the operation in step
2. Attention -1 ResumingtheDefaultSetting[Reset] There are two types of Reset. One is to reset the color adjustment only to the default settings, and the other
is to reset all the settings to the default settings.
· After resetting, you cannot undo the operation. Toresetcoloradjustmentvalues Only the adjustment values in the current FineContrast mode will revert to the
default settings (factory settings). (1) Choose <Color> from the Adjustment menu, and press . (2) Choose <Reset> from the <Color> menu and press . The
<Reset> menu appears. (3) Select <Reset> with or , and press The color adjustment values revert to the default settings. NOTE .
Toresetalladjustmentstothefactorydefaultsettings Reset all adjustments to the factory default settings. (1) Choose <Others> from the Adjustment menu, and
press (2) Choose <Reset> from the <Others> menu, and press . The <Reset> menu appears.
. · For main default settings, refer to "Main default settings (factory settings)" on page 44. (3) Select <Reset> with or , and press All setting values revert to
the default settings. . 0 Chapter 2 Settings and Adjustments Chapter ConnectingCables -1 ConnectingMorethanTwoPCstothe Monitor More than two PCs can
be connected to the monitor through the D-Sub mini 15 pin, the DVI-D and the DisplayPort connector on the back of the monitor. Connectionexamples
DisplayPort DVI-D connector connector D-Sub mini 15-pin Connector To PC 1 D-Sub mini 15-pin Connector Analog Signal cable (supplied MD-C87) To PC
2 DVI connector Digital(DVI) Signal cable (supplied FD-C39) To PC 3 DisplayPort connector Digital(DisplayPort) Signal cable (PP200 option) Chapter 3
Connecting Cables 1 Toswitchtheinputsignal The input signal switches each time is pressed. When the signal is switched, the active input port name appears
at the top right corner of the screen. Tosetinputsignalselection[InputSignal] Setting Auto Function The monitor recognizes the connector through which PC
signals are input. When a PC is turned off or enters the powersaving mode, the monitor automatically displays another signal. The monitor detects only the
PC's signals currently displaying automatically.
Select an active input signal with . NOTE · When "Auto" is selected for <InputSignal>, the monitor's powersaving function works only when all PCs are in the
power-saving mode. Manual [Inputsignalsetting] . (1) Choose <Others> from the Adjustment menu, and press (2) Choose <Input Signal> from the <Others>
menu, and press The <Input Signal> menu appears. .
(3) Select "Auto" or "Manual" with The setting is completed. or , and press . Chapter 3 Connecting Cables Chapter Troubleshooting If a problem still remains
after applying the suggested remedies, contact your local dealer. · · · · No-picture problems See No.1 - No.
2. Imaging problems (digital input) See No.3 - No.8. Imaging problems (analog input) See No.3 - No.11. Other problems See No.12 - No.17.
Problems 1. Nopicture · Power indicator does not light. Possiblecauseandremedy · Check whether the power cord is connected correctly. If the problem
persists, turn off the monitor, and then turn it on again a few minutes later. · Turn the main power switch on. · Press . · Set each adjusting value in
[Brightness], [Contrast] and [Gain] to higher level. (see page 20, 21, 22) · · · · . Switch the input signal with Operate the mouse or keyboard. Check whether
the PC is turned on.
When the EcoView Sense is on, the monitor may have shifted to the power saving mode. Come near to the monitor. · Power indicator is lighting blue. · Power
indicator is lighting orange. · Power indicator flashes orange.
· There is a problem in the device that uses DisplayPort connection. Solve the problem, turn off the monitor, and then turn it on again. Refer to the user's
manual of the device that uses DisplayPort connection for details. This message appears when the signal is not input correctly even when the monitor
functions properly. · The message shown left may appear, because some PCs do not output the signal soon after power-on.
· Check whether the PC is turned on. · Check whether the signal cable is connected properly. · Switch the input signal with . . Themessagebelowappears. · This
message appears when no signal is input. Example: · The message shows that the input signal is out of the specified frequency range. (Such signal frequency
is displayed in red.) Example: · Check whether the signal setting of your PC matches the resolution and the vertical frequency settings for the monitor. (see
page 10) · Reboot the PC.
· Select an appropriate display mode using the graphics board's utility. Refer to the manual of the graphics board for details. fD : Dot Clock (Displayed only
when the digital signal inputs) fH : Horizontal Frequency fV : Vertical Frequency · Adjust using [Brightness] or [Contrast]. (The LCD monitor backlight has
a fixed life span. When the screen becomes dark or begins to flicker, contact your local dealer.) · Check whether the signal setting of your PC matches the
resolution and the vertical frequency settings for the monitor.
You're reading an excerpt. Click here to read official EIZO
FLEXSCAN EV2333W user guide
http://yourpdfguides.com/dref/3610229
(see page 10) · Adjust using [Smoothing]. (see page 18) . Thescreenistoobrightortoodark. .
Charactersareblurred. Chapter 4 Troubleshooting Problems . Afterimagesappear. Possiblecauseandremedy · Afterimages are particular to LCD monitors.
Avoid displaying the same image for a long time.
· Use the screen saver or power save function to avoid displaying the same image for extended periods of time. 6.
Green/red/blue/whitedotsordefectivedotsremain · This is due to LCD panel characteristics and is not a onthescreen. failure. 7.
Interferencepatternsorpressuremarksremainon · Leave the monitor with a white or black screen. The thescreen. symptom may disappear. 8.
Noiseappearsonthescreen. · Set [Overdrive] to [Off]. (see page 22) · When entering the signals of HDCP system, the normal images may not be displayed
immediately. · Adjust image position so that it is displayed properly within the display area using [Position]. (see page 18) · If the problem persists, use the
graphics board's utility if available to change the display position. 9.
Displaypositionisincorrect. 10. Verticalbarsappearonthescreenorapartofthe imageisflickering. · Adjust using [Clock]. (see page 17) 11.
Wholescreenisflickeringorblurring. · Adjust using [Phase]. (see page 17) 1. The<Smoothing>iconontheAdjustmentmenu <Screen>cannotbeselected. · You
cannot choose the smoothing icon when the screen is displayed in the following resolutions or settings.
· 1920 × 1080 · Select [Normal] during <Screen Size>. · Check whether the operation lock function works. (see page 28) · Check whether the Adjustment
menu is displayed. (see page 11) · This function does not work when digital signal is input. · This function does not work correctly with some graphics boards.
· Check whether the mini jack cable is correctly connected. · Check whether volume is set to 0. · Check the setting of the PC and the audio playback software. ·
During DisplayPort signal input, check the [Source] setting. (see page 23) 1.
Theadjustmentmenudoesnotappear. 1. TheFineContrastmodeisnotdisplayed. 1. Theautoadjustfunctiondoesnotworkcorrectly. 16. Noaudiooutput. Chapter 4
Troubleshooting Problems Possiblecauseandremedy · Check the setting environment of the monitor. 17. (WhenusingEcoViewSense)
Theimagesremainstobedisplayedwhenyou EcoView Sense may not work correctly in the following moveawayfromthemonitor.
Theimagesdoesnot environments. reappearwhenyoucomenearit. · There is something that reflects the light such as mirror or glass in front of the sensor. · The
monitor is located in a place that receive direct sunlight. · There is some infrared device near the monitor. · There is some obstacle in front of the sensor. ·
Check whether any dirt on the sensor. Clean the sensor with a soft cloth. · Check whether you are in front of the monitor. The infrared ray is emitted vertically
from the sensor to detect a person.
· Check whether the off timer function is on. If it is on, the monitor turns off automatically after a specified time has passed. Therefore, the images does not
reappear on the screen even though you come near to it. Press to turn on the monitor (see page 24). Chapter 4 Troubleshooting Chapter Reference -1
HowtoAttachtheOptionalArm An optional arm (or an optional stand) can be attached by removing the stand section.
Please refer to our web site for the corresponding optional arm (or optional stand). http://www.eizo.com Attention 1
Whenusingthemonitorwith"Portrait"position,changethe positionto"Landscape". 2 LaytheLCDmonitoronasoftclothspreadoveronastable
surfacewiththepanelsurfacefacingdown.
· When attaching an arm or stand, follow the instructions of their user's manual. · When using another manufacturer's arm or stand, confirm the following in
advance and select one conforming to the VESA standard. Use the M4 × 12 screws supplied with this monitor. Clearance between the screw holes: 100 mm ×
100 mm Thickness of plate: 2.6 mm Strong enough to support weight of the monitor unit (except the stand) and attachments such as cables. · When using an
arm or stand, attach it to meet the following tilt angles of the monitor. Up 45 degrees, down 45 degrees (horizontal display, and vertical display rotated 90
degrees clockwise) · Connect the cables after attaching an arm. · Do not move the removed stand up and down. Doing so may result in injury or device
damage. 6 Chapter 5 Reference 3 Removethestand.
FlexStand Remove the stand from the monitor while releasing the lock. TriStand Prepare a screwdriver. Loosen the screw securing the unit and the stand with
the screwdriver. 4 Attachthemonitortothearmorstand. Secure the monitor to the arm or stand using the screws specified in the user's manual of the arm or
stand. Chapter 5 Reference 7 - AttachingtheFlexStand The once removed the FlexStand can be attached to the monitor again with the following procedures. 1
Puttheinsertionpartofthestandintheslotofthemonitor. At the time, use as a guide that the marks (1) on the stand match to the screw holes (2) of the monitor.
Screw holes Marks 2 Attachthestandmovingthemonitortowardthestand. Make sure that the lock is latched with clicking sound shown in the figure below.
Incorrect Correct 8 Chapter 5 Reference - AttachingtheTriStand The once removed the TriStand can be attached to the monitor again with the following
procedures. 1 LaytheLCDmonitoronasoftclothspreadoveronastable surfacewiththepanelsurfacefacingdown. 2
Puttheinsertionpartofthestandintheslotofthemonitor. 3 Prepareascrewdriver.Presstheupperpartofthestand
againsttheunitandtightenthescrewwiththescrewdriverto fixthestandtotheunit.
Chapter 5 Reference 9 - FoldingtheTriStand Perform the following procedures to remove the stand base and fold the stand when re-packing a monitor with a
TriStand. 1 Openthecableholder. 2 Adjustthemonitortoitslowestposition,andinsertapininto thestand. 3 LaytheLCDmonitoronasoftclothspreadoveronastable
surfacewiththepanelsurfacefacingdown. 4 Openthecoverofstandbase.
0 Chapter 5 Reference 5 Rotatethestandbaseinacounterclockwisedirectionwhile holdingdowntheprotrusion,andthenremovethestandbase. Chapter 5 Reference
1 5-5 Specifications EV1W LCD Panel Dot Pitch Horizontal Scan Frequency Vertical Scan Frequency 23.0-inch (580 mm) TFT color LCD with anti-glare
hard coating Viewing angle: Horizontal 170°, Vertical 160° (CR:10 or more) 0.2655mm Analog: 31-81kHz Digital (DVI-D/DisplayPort): 31-68kHz Analog:
55-76Hz (Non-interlace) Digital (DVI-D/DisplayPort): 59-61Hz (Non-interlace) (VGA TEXT: 69-71Hz) 1920 dots × 1080 lines Analog: 148.5MHz Digital
(DVI-D/DisplayPort): 148.
You're reading an excerpt. Click here to read official EIZO
FLEXSCAN EV2333W user guide
http://yourpdfguides.com/dref/3610229
5MHz Approx. 16.77 million colors (1064.33 million colors/10bit LUT) 509.76mm × 286.
74mm 100-120 VAC ±10%, 50/60Hz 0.57A 200-240 VAC ±10%, 50/60Hz 0.35A Screen Display On Power saving mode Power button Off Main Power switch
Off Input Signal Connector 35W or less (Speaker working) 32W or less (Speaker not working) 0.9W or less (for D-Sub single signal input, when stereo mini
jack cable is not connected, [EcoView Sense] : "Off") 0.1W or less (when stereo mini jack cable is not connected) 0W D-Sub mini 15-pin DVI-D connector
(Applicable to HDCP) DisplayPort (Standard V1.1a, applicable to HDCP and 8-bit) Applicable Format (Audio signal) - 2ch linear PCM (32kHz / 44.1kHz /
48kHz /88.2kHz / 96kHz / 176.4kHz/ 192kHz) Analog Input Signal (Sync) Analog Input Signal (Video) Digital Signal (DVI-D) Transmission System Video
Signal Memory Audio Output Line input Plug & Play Dimensions (Width) × (Height) × (Depth) Main unit (including FlexStand) Main unit (including
TriStand) Separate, TTL, positive/ negative Analog, Positive (0.7Vp-p/75) TMDS (Single Link) Analog signal: 45 Digital signal (DVI-D/DisplayPort): 10
Speaker output: 0.
35W (8, THD: 10% or less) Headphone output: 2mW + 2mW Input impedance : 48 k (typ.) Input level :1.0 Vrms (Max.) Analog / Digital (DVI-D) : VESA
DDC 2B / EDID structure 1.3 Digital (DisplayPort) : VESA DisplayPort / EDID structure 1.
4 547 mm (21.5 inch) × 517.8 - 346.5 mm (20.4 - 13.
6 inch) × 236 - 221 mm (9.3 - 8.7 inch) 547 mm (21.5 inch) × 442 - 382 mm (17.4 - 15 inch) × 200 mm (7.9 inch) Resolution Max. Dot Clock Max. Display
Color Display Area (H × V) Power Supply Power Consumption Main unit (without stand) 547 mm (21.5 inch) × 332 mm (13.1 inch) × 44 mm (1.
73 inch) Chapter 5 Reference Mass Main unit (including FlexStand) Main unit (including TriStand) Approx. 6.4 kg (14.1 lbs.) Approx. 4.8 kg (10.6 Ibs.) Main
unit (without stand) Approx. 3.
6 kg (7.9 lbs.) Movable range FlexStand Tilt: 30° Up, 0° Down Swivel: 172° Right, 172° Left Adjustable height: 225 mm (8.9 inch) (171.3 mm (6.
7 inch) when Tilt is 0°) Rotation: 90° (clockwise) Tilt: 25° Up, 0° Down Swivel: 172° Right, 172° Left Adjustable height: 60 mm (2.36 inch) Operating: 5 °C 35 °C (41 °F - 95 °F) Storage: -20 °C - 60 °C (-4 °F - 140 °F) Operating: 20% - 80% R.H. (no condensation) Storage: 10% - 90% R.H.
(no condensation) Operating: 700 to 1,060 hPa Storage: 200 to 1,060 hPa TriStand Environmental Conditions Temperature Humidity Pressure EVW LCD
Panel Dot Pitch Horizontal Scan Frequency Vertical Scan Frequency 23.0-inch (580 mm) TFT color LCD with anti-glare hard coating Viewing angle:
Horizontal 178°, Vertical 178° (CR:10 or more) 0.2655mm Analog: 31-81kHz Digital (DVI-D/DisplayPort): 31-68kHz Analog: 55-76Hz (Non-interlace)
Digital (DVI-D/DisplayPort): 59-61Hz (Non-interlace) (VGA TEXT: 69-71Hz) 1920 dots × 1080 lines Analog: 148.5MHz Digital (DVI-D/DisplayPort):
148.5MHz Approx. 16.77 million colors (1064.33 million colors/10bit LUT) 509.76mm × 286.74mm 100-120 VAC ±10%, 50/60Hz 0.
75A 200-240 VAC ±10%, 50/60Hz 0.45A Screen Display On Power saving mode Power button Off Main Power switch Off Input Signal Connector 45W or
less (Speaker working) 42W or less (Speaker not working) 1W or less (for D-Sub single signal input, when stereo mini jack cable is not connected, [EcoView
Sense] : "Off") 0.1W or less (when stereo mini jack cable is not connected) 0W D-Sub mini 15-pin DVI-D connector (Applicable to HDCP) DisplayPort
(Standard V1.1a, applicable to HDCP and 8-bit) Applicable Format (Audio signal) - 2ch linear PCM (32kHz / 44.1kHz / 48kHz /88.2kHz / 96kHz / 176.4kHz/
192kHz) Analog Input Signal (Sync) Analog Input Signal (Video) Digital Signal (DVI-D) Transmission System Separate, TTL, positive/ negative Analog,
Positive (0.7Vp-p/75) TMDS (Single Link) Resolution Max. Dot Clock Max. Display Color Display Area (H × V) Power Supply Power Consumption Chapter
5 Reference Video Signal Memory Audio Output Line input Plug & Play Dimensions (Width) × (Height) × (Depth) Main unit (including FlexStand) Main unit
(including TriStand) Analog signal: 45 Digital signal (DVI-D/DisplayPort): 10 Speaker output: 0.
35W (8, THD: 10% or less) Headphone output: 2mW + 2mW Input impedance : 48 k (typ.) Input level :1.0 Vrms (Max.) Analog / Digital (DVI-D) : VESA
DDC 2B / EDID structure 1.3 Digital (DisplayPort) : VESA DisplayPort / EDID structure 1.
4 547 mm (21.5 inch) × 517.8 - 346.5 mm (20.4 - 13.
6 inch) × 236 - 221 mm (9.3 - 8.7 inch) 547 mm (21.5 inch) × 442 - 382 mm (17.4 - 15 inch) × 200 mm (7.9 inch) Main unit (without stand) 547 mm (21.5
inch) × 332 mm (13.1 inch) × 47.5 mm (1.87 inch) Mass Main unit (including FlexStand) Main unit (including TriStand) Approx.
7.1 kg (15.7 lbs.) Approx. 5.5 kg (12.1 Ibs.) Main unit (without stand) Approx. 4.3 kg (9.
5 lbs.) Movable range FlexStand Tilt: 30° Up, 0° Down Swivel: 172° Right, 172° Left Adjustable height: 225 mm (8.9 inch) (171.3 mm (6.7 inch) when Tilt is
0°) Rotation: 90° (clockwise) Tilt: 25° Up, 0° Down Swivel: 172° Right, 172° Left Adjustable height: 60 mm (2.
36 inch) Operating: 5 °C - 35 °C (41 °F - 95 °F) Storage: -20 °C - 60 °C (-4 °F - 140 °F) Operating: 20% - 80% R.H. (no condensation) Storage: 10% - 80%
R.H. (no condensation) Operating: 700 to 1,060 hPa Storage: 200 to 1,060 hPa TriStand Environmental Conditions Temperature Humidity Pressure
Maindefaultsettings(factorysettings) Auto EcoView EcoView Sense EcoView Index Smoothing FineContrast Mode PowerManager - Power Save Input Signal
Screen Size Off Timer Menu Settings Menu Size Menu Off Timer Language On On On 3 Custom On Manual Full Screen Disable Normal 45 sec English
Chapter 5 Reference 17.
6(0.69) · TriStand 81.5 (3.21) 628.5(24.7) 465(18.3) OutsideDimensions EV1W · FlexStand 547(21.5) 511.8(20.1) PIVOT 17 2° 17.
6(0.69) 24.8(0.98) 288.8(11.4) 332(13.1) 382(15) 44(1.73) 243.5(9.6) 185.
8(7.3) 541.3(21.3) 18.4(0.
72) 21.5(0.85) 24.8(0.98) 288.
8(11.4) 332(13.1) 517.8(20.4) 14.5(0.57) 263(10.4) 179.9(7.1) 442(17.
4) 67.9(2.67) 49.9(1.96) 9.5(0.37) 355(14) 411.1(16.2) 346.5(13.
6) 16(0.63) 145(5.7) 377.8(14.9) 221(8.
7) 60(2.36) 183.7(7.2) 325.4(12.
8) unit : mm (inch) unit : mm (inch) 107 (4.2) 157.5(6.2) 67.5 (2.66) 107 157.5(6.2) 67.5 (2.66) (4.
2) ° SWIVEL 90 17 2° 18.4(0.72) 21.5(0.85) 12.4(0.49) 17 2° 17.6(0.69) 17 2° SWIVEL 465(18.3) 547(21.
5) 511.8(20.1) 200(7.9) 30° TILT 56.1(2.
21) 216(8.5) 236(9.3) 44(1.73) 57.6(2.
27) 25° TILT 200(7.9) 190(7.5) 142.5(5.6) 12.4(0.49) 195.5(7.7) Chapter 5 Reference 547(21.5) 511.
8(20.1) PIVOT Chapter 5 Reference 17 2° 17 2° 17.6(0.69) 288.8(11.4) 332(13.1) 382(15) 47.5(1.87) 243.5(9.
6) 185.8(7.3) 542.
You're reading an excerpt. Click here to read official EIZO
FLEXSCAN EV2333W user guide
http://yourpdfguides.com/dref/3610229
Powered by TCPDF (www.tcpdf.org)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising