INSTALLATION

INSTRUCTIONS

PARTS LIST

Attachment Kit

P/N: 08B21-SJC-102

Rear camera trim

Accessory

REAR CAMERA

ATTACHMENT

(EX-L WITH NAVI)

Template

Application

2007 RIDGELINE

Publications No.

AII 33263-38883

Issue Date

FEB 2008

19 Wire ties

Rear camera bracket

10 Small wire ties

Rear camera subbracket

Harness clamp bracket A

Harness clamp bracket B

Rear camera subharness

© 2008 American Honda Motor Co., Inc. - All Rights Reserved.

6 Wire ties with clip

6-Pin connector

Grommet

2 Clear adhesive tapes

3 Blind nuts

AII 33263-38883 (0802) 08B21-SJC-1010-91

1 of 18

2 EPT sealers

4 Cushion tapes

2 Socket bolts, 4 x 10 mm

3 Washer screws, 4 x 12 mm

2 Washer screws, 4 x 6 mm

7 Clips

Round grommet

6 Oval grommets

Accessory user’s information manual

Rear Camera Kit (sold separately)

P/N: 08A57-SJC-100

Rear camera

2 of 18

TOOLS AND SUPPLIES REQUIRED

Phillips screwdriver

Flat-tip screwdriver

10 mm Combination wrench

Ratchet

10 mm, 12 mm, and 14 mm Socket

Torque wrench

File

Isopropyl alcohol

Shop towel

Tape measure

Drill

3 mm, 8 mm, and 10 mm Drill bits

Utility knife

T40 and T50 Torx bit

KTC trim tool

Scissors

Tape

Electrical tape

Wire

3 mm Hex wrench

Illustration of the Rear Camera Installed on the

Vehicle

NAVI CONTROL UNIT

GROMMET

REAR

CAMERA

REAR CAMERA

SUBHARNESS

6-PIN CONNECTOR

4712100K

INSTALLATION

Customer Information: The information in this

installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”

1.

Make sure you have the anti-theft code for the radio, then write down radio station presets.

2. Disconnect the negative cable from the battery.

AII 33263-38883 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved.

3.

Remove the fuel fill door release handle. Remove the left front door sill trim (three clips and three retaining tabs).

RETAINING

TABS

FUEL FILL DOOR

RELEASE HANDLE

3 CLIPS

LEFT FRONT

DOOR SILL TRIM

RETAINING

TAB

5.

Pull away the weatherstrip from the B-pillar lower trim panel. Remove the left seat belt lower anchor bolt cover and remove the lower anchor bolt.

Remove the left B-pillar lower trim panel by pulling out toward you as shown.

Seat belt anchor bolt torque:

30 to 35 N·m (22 to 25 lbs)

WEATHERSTRIP

(Pull away.)

FRONT

LEFT

B-PILLAR

LOWER

TRIM

PANEL

FRONT

3916041T

4. Remove the left rear door sill trim (three clips and four retaining tabs).

RETAINIG

TABS

3 CLIPS

LEFT REAR

DOOR SILL TRIM

RETAINIG

TABS

LOWER ANCHOR

BOLT COVER

LEFT SEAT BELT

LOWER ANCHOR BOLT

4212330T

6. Remove the driver’s seat frame rear cover (two clips and two hooks).

DRIVER’S SEAT

FRONT

© 2008 American Honda Motor Co., Inc. - All Rights Reserved.

4212450T

AII 33263-38883 (0802)

2 HOOKS

2 CLIPS

DRIVER’S SEAT

FRAME REAR COVER

4713010K

3 of 18

7.

Lift up the rear seats, and remove the rear seat under covers;

• Remove the right rear seat under cover (four clips).

• Remove the left rear seat under cover (five clips).

LEFT REAR

SEAT CUSHION

RIGHT REAR

SEAT CUSHION

9.

Remove the rear seat belt anchor bolt and eight seat anchor bolts.

Seat belt anchor bolt torque:

30 to 35 N·m (22 to 25 lbs)

RIGHT REAR

SEAT UNDER

COVER

9 CLIPS

LEFT REAR

SEAT UNDER

COVER

4212342T

8. Remove the rear seat bracket covers;

• Remove the left and right rear seat bracket covers (two clips for each cover).

• Remove the center seat bracket cover (two clips and nine retaining tabs).

LEFT REAR

SEAT BRACKET

COVER

CLIPS

8 SEAT

ANCHOR

BOLTS

REAR SEAT

BELT ANCHOR

BOLT

4212362T

10. Remove the cap from the rear trim panel cover

(four retaining tabs for each cover), and remove the rear seat.

4 RETAINING

TABS

CAP

4 RETAINING

TABS

CAP

4 of 18

9 RETAINING

TABS

2 CLIPS

CENTER SEAT

BRACKET

COVER

RIGHT REAR

SEAT BRACKET

COVER

CLIPS

4212460T

AII 33263-38883 (0802)

REAR SEAT

4212371T

© 2008 American Honda Motor Co., Inc. - All Rights Reserved.

11. Remove the rear trim panel cover (eight clips and two retaining tabs).

2 RETAINING

TABS

REAR TRIM

PANEL COVER

14. Remove the left rear lower anchor bolt cover, and remove the left rear seat belt lower anchor bolt.

Seat belt anchor bolt torque:

30 to 35 N·m (22 to 25 lbs)

6 CLIPS

2 CLIPS

CLIP

CLIPS

12. Remove the left rear seat belt upper anchor bolt cover (four retaining tabs), and remove the left rear seat belt upper anchor bolt.

Seat belt anchor bolt torque:

30 to 35 N·m (22 to 25 lbs)

CLIP

LEFT REAR SEAT

BELT UPPER

ANCHOR BOLT

4 RETAINING

TABS

4212381T

LEFT REAR

LOWER

ANCHOR

BOLT COVER

LEFT REAR

SEAT BELT

LOWER

ANCHOR

BOLT

4715611K

LEFT REAR

PILLAR

LOWER TRIM

15. Remove upper clip, then pull the left rear pillar lower trim out toward you to release two clips.

16. Remove the left rear taillight (two bolts, two clips, and vehicle connector). Remove the right taillight the same way.

LEFT SIDE RIGHT SIDE

VEHICLE

CONNECTOR

VEHICLE

CONNECTOR

BOLTS

LEFT REAR

SEAT BELT

ANCHOR BOLT

COVER

2 TABS

LEFT REAR PILLAR

UPPER TRIM

CLIP

4715601K

13. Remove the left rear pillar upper trim.

• With side airbag; pull the clip, and remove the left rear pillar trim by releasing the one clip.

• Without side airbag; remove the left rear pillar trim by releasing the two clips.

2 CLIPS

LEFT

TAILLIGHT

VEHICLE

CONNECTOR

3924012H

© 2008 American Honda Motor Co., Inc. - All Rights Reserved.

AII 33263-38883 (0802)

5 of 18

17. Remove the rear bumper:

• Remove the license plate (two bolts).

• Remove two bolts, six self-tapping screws, and six clips from the rear bumper.

• Pull the rear bumper toward you. Unplug the two vehicle connectors, and remove the rear bumper.

• Set the rear bumper on the blanket.

2 VEHICLE

CONNECTORS

6 CLIPS

• Using a KTC trim tool, carefully pry up the front of the trim to release the three front clips.

Start with the left clip and work towards the right clip.

• Gently left the front of the trim to release the four rear clips.

7 CLIPS

KTC TRIM TOOL

RIGHT CLIP

(Finish here.)

REAR

BUMPER

2 BOLTS

8 SELF-

TAPPING

SCREWS

LICENSE PLATE

BOLTS

3003063H

18. Remove the rear roof trim:

• Remove the roof trim nut covers (two retaining tabs for each cover).

• Remove the two nuts.

ROOF TRIM

NUT COVER

2 RETAINING

TABS

2 NUTS

LEFT CLIP

(Start here.)

4 CLIPS

CENTER CLIP

(Second.)

4D19062H

• Remove the antenna grommet from the roof, unplug the vehicle connector, and remove the rear roof trim.

2 HOOKS

REAR

ROOF TRIM

HIGH-MOUNT

BRAKE LIGHT

GROMMET

6 of 18

REAR ROOF TRIM

4D19051H

AII 33263-38883 (0802)

ANTENNA

GROMMET

2 VEHICLE

CONNECTORS

4804024H

© 2008 American Honda Motor Co., Inc. - All Rights Reserved.

19. Remove and discard the grommets from the roof panel, and install the six oval grommets and one round grommet into the roof panel.

GROMMET

(Discard.)

ROUND

GROMMET

21. Remove the left C-pillar outer trim (slide rearward, and unplug the vehicle connector).

Remove the clips from the body, and reinstall the clips to the left C-pillar outer trim.

3 CLIPS

(Install.)

ROOF PANEL

6 OVAL

GROMMETS

3 CLIPS

(Remove.)

VEHICLE PANEL

LEFT C-PILLAR

OUTER TRIM

LEFT C-PILLAR

OUTER TRIM

VEHICLE

CONNECTOR

6 GROMMETS

(Discard.)

4D20510K

20. On the rear roof trim backside, remove and discard the clips from the rear roof trim, and install the seven clips to the rear roof trim.

4611021H

22. Remove the left front anchor (two TORX bolts).

REAR ROOF TRIM

LEFT FRONT

ANCHOR

7 CLIPS

T50 TORX

BOLTS

4610041H

4D20501K

7 CLIPS

(Discard.)

© 2008 American Honda Motor Co., Inc. - All Rights Reserved.

AII 33263-38883 (0802)

7 of 18

23. Remove the front bed panel (six TORX bolts).

25. Remove the left lower bed light (one self-tapping screw, pull the light out towards you and unplug the vehicle connector).

LEFT LOWER

BED LIGHT

SELF-TAPPING

SCREW

CLIP

VEHICLE

CONNECTOR

LEFT REAR

ANCHOR

T50 TORX

BOLT

6 T40 TORX

BOLTS

FRONT BED

PANEL

3929032H

24. Remove the left bed rail trim:

• Remove the screw cover (four retaining tabs).

• Remove the self-tapping screw.

• Pull the left bed rail trim back to release the six clips, and remove the left bed rail trim.

4 RETAINING

TABS

6 CLIPS

SCREW

COVER

LEFT BED

RAIL TRIM

3926062H

26. Remove the left rear anchor (two TORX bolts).

27. Remove the left side bed panel (six TORX bolts).

LEFT SIDE

BED PANEL

SELF-

TAPPING

SCREW

6 T40 TORX

BOLTS

3926021H

LEFT BED

RAIL TRIM

3926071H

8 of 18

AII 33263-38883 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved.

28. Remove the tailgate trim:

• Remove the four screws and release the one end clip on each side.

• Sharply push the tailgate to the right to release the 16 clips from the trim.

• Remove the 16 clips from the tailgate and reinstall the 16 clips to the tailgate trim in the direction shown.

TAILGATE

TRIM

16 CLIPS

30. Get the template. Using a scissors, cut out the marked area from the template. Align the edge of the template with the edge of the tailgate as shown, and attach it to the tailgate tape.

OUTER

TAILGATE

CUT

TEMPLATE

TAILGATE

UPPER

HANDLE

TEMPLATE

9 TAPES

2 CLIPS

TAILGATE TRIM

4605080T

4 SELF-

TAPPING

SCREWS

29. Remove the tailgate panel (seven TORX screws).

7 T40 TORX

SCREWS

TAILGATE

PANEL

4707041K

CUT

AREA

31. Center punch the tailgate at the marks on the template. Remove the template.

TAILGATE

4 MARKS

TAILGATE

UPPER

HANDLE

CENTER

PUNCH

CUT

TEMPLATE

4708010K

4605090T

© 2008 American Honda Motor Co., Inc. - All Rights Reserved.

AII 33263-38883 (0802)

9 of 18

32. Drill three 8 mm holes and one 10 mm hole in the tailgate.

• Wrap tape around a 3 mm drill bit, and 8 mm drill bit and a 10 mm drill bit 10 to 15 mm from the end or use a drill stop.

• While wearing eye protection, drill a 3 mm hole, then an 8 mm hole in all four locations.

Drill a 10 mm hole only in the upper center hole.

• Remove any burrs, and apply touch-up paint to all of the holes.

10 ~ 15 mm

DRILL BIT

(3 mm 8 mm

10 mm)

DRILL BIT

TAPE

(Wrap tape around the drill bit.)

TAILGATE

UPPER

CENTER

HOLE

34. Remove the four screws from the rear camera.

Route the rear camera harness through the rear camera subbracket, and install the rear camera subbracket to the rear camera with the four screws.

REAR

CAMERA

REAR CAMERA

SUBBRACKET

DRILL

4 MARKS

DRILL BIT

(3 mm 8 mm)

4708021K

33. Install one blind nut into each 8 mm hole.

REAR CAMERA

HARNESS

4 SCREWS

4708050K

35. Attach a piece of wire to the terminals from the rear camera harness, and tape the wire to the terminals.

REAR CAMERA

HARNESS

TAILGATE

TERMINALS

4913020K

BLIND

NUTS

3 8 mm

HOLES

4708030K

TAPE WIRE

10 of 18

AII 33263-38883 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved.

36. Route the rear camera harness through the 10 mm hole in the tailgate, and seat the grommet into the

10 mm hole.

10 mm

HOLE

REAR CAMERA

HARNESS

GROMMET

WIRE

38. Align the two locating tabs on the rear camera subbracket with the slots in the rear camera bracket, and install two 4 x 6 mm washer-screws.

NOTE: Make sure the flat surface of the rear camera subbracket is facing up: otherwise, the camera view will be upside down.

4 x 6 mm

WASHER

SCREW

REAR CAMERA

BRACKET

2 SLOTS

GROMMET

VEHICLE PANEL

4708071K

37. Install the rear camera bracket to the three blind nuts with three 4 x 12 mm washer-screws.

BLIND

NUTS

TAILGATE PANEL

REAR CAMERA

SUBBRACKET

(Flat surface facing up.)

2 LOCATING

TABS

4 x 6 mm

WASHER

SCREW

4708081K

4 x 12 mm

WASHER

SCREWS

REAR CAMERA

BRACKET

4708041K

© 2008 American Honda Motor Co., Inc. - All Rights Reserved.

AII 33263-38883 (0802)

11 of 18

39. Install clear adhesive tapes to the tailgate:

• Open the tailgate.

• Get the clear adhesive tapes. Using scissors, cut 30 mm from the end of each adhesive tape.

• Using isopropyl alcohol on a shop towel, clean the tailgate where the adhesive tapes will attach.

40. Route the rear camera harness along the tailgate as shown.

REAR CAMERA

HARNESS

TAILGATE

REAR

REAR

TAILGATE

4708092K

41. Remove the TORX bolt from the tailgate hinge, and attach the harness clamp bracket B to the tailgate using the TORX bolt you just removed. Do not tighten the TORX bolt at this time.

T50 TORX BOLT

(Do not tighten at this time.)

HARNESS CLAMP

BRACKET B

CLEAR

ADHESIVE

TAPE

30 mm

TAILGATE

HINGE

CLEAR

ADHESIVE

TAPE

30 mm

SECOND

ADHESIVE TAPE

TAILGATE

TAILGATE

LIP

FIRST

ADHESIVE

TAPE

4N09043K

12 of 18

AII 33263-38883 (0802)

TAILGATE

5D10010T

© 2008 American Honda Motor Co., Inc. - All Rights Reserved.

42. Secure the rear camera harness to the harness clamp bracket B with three small wire ties. Attach the wire tie over the tape attached to the harness.

HARNESS

CLAMP

BRACKET B

T50 TORX BOLT

(Torque to 29 to32 N·m)

REAR

CAMERA

HARNESS

SMALL

WIRE TIE

100 mm

25 mm

TAPE

SMALL

WIRE TIE

(Attach over the tape.)

5D10020T

43. Torque the T50 TORX bolt to 29 to 32 N·m (21 to

23 lbs).

44. Close the tailgate. Remove the lower outboard hinge bolt, and attach harness clamp bracket A to the tailgate hinge with the TORX bolt you just removed. Do not tighten the TORX bolt at this time.

TAIL GATE

45. Pull the rear camera harness out from the inside of the tailgate, and secure the rear camera harness to the harness clamp bracket A with one small wire tie.

TAIL

GATE

T50 TORX

BOLT

(Torque to

29 to32 N·m)

REAR

CAMERA

HARNESS

130 mm

SMALL

WIRE TIE

HARNESS

CLAMP

BRACKET A

5D10041T

46. Torque the T50 TORX bolt to 29 to 32 N·m (21 to

23 lbs).

47. Using isopropyl alcohol on a shop towel, clean the tailgate where the cushion tapes will attach. Using scissors, cut one cushion tape in half. Secure the rear camera harness to the tailgate with two half cushion tapes and two full cushion tapes at the locations shown.

CUSHION TAPE

REAR CAMERA

HARNESS

HARNESS

CLAMP

BRACKET A

TAIL GATE

HINGE

5D10030T

T50 TORX BOLT

(Do not tighten at this time.)

© 2008 American Honda Motor Co., Inc. - All Rights Reserved.

AII 33263-38883 (0802)

TAILGATE

REAR

CUSHION TAPE

(Cut in half.)

4N09050K

13 of 18

48. Secure the rear camera harness to the tailgate with five wire ties with clip.

TAILGATE

5 WIRE TIES

WITH CLIP

TAILGATE

51. Route the rear camera harness out through the bed panel hole, and secure the rear camera harness to the vehicle harness with one wire tie just inside the panel hole.

BED PANEL HOLE

REAR

REAR

CAMERA

HARNESS

WIRE

TIE

FRONT

VEHICLE

HARNESS

CUSHION TAPE

(Cut in half.)

REAR CAMERA

HARNESS

4708103K

49. Using isopropyl alcohol on a shop towel, clean the tailgate where the cushion tape will attach. Using scissors, cut one cushion tape in half. Secure the rear camera harness to the tailgate with one half cushion tape.

50. Route the rear camera harness through the left side vehicle panel hole, and secure the rear camera harness to the vehicle harness with two wire ties.

REAR CAMERA

HARNESS

LEFT SIDE

VEHICLE

PANEL

4709050K

52. Route the rear camera harness along the vehicle harness towards the front of the vehicle, and secure it to the vehicle harness with six wire ties in the areas shown.

6 WIRE TIES

VEHICLE

HARNESS

LEFT SIDE

VEHICLE

PANEL HOLE

WIRE TIES

VEHICLE

HARNESS

5D10050T

REAR CAMERA

HARNESS

4709062K

14 of 18

AII 33263-38883 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved.

53. Remove the vehicle grommet from the left

C-pillar.

LEFT C-PILLAR

VEHICLE

GROMMET

OPENING

VEHICLE

GROMMET

BED BULKHEAD

WIRE

56. Inside the passenger’s compartment turn down the rear panel insulator. Pull the rear camera harness out from the hole in the C-pillar, and remove the tape and wire from the rear camera harness.

REAR

CAMERA

HARNESS

GROMMET

4709071K

54. Insert the rear camera harness through the grommet, and route the rear camera harness through the vehicle grommet opening. Seat the grommet into the grommet hole.

55. Using electrical tape, secure the grommet to the rear camera harness, and pay attention to the angle of the grommet.

GROMMET

REAR

CAMERA

HARNESS

TAPE

C-PILLAR

GROMMET

UP

© 2008 American Honda Motor Co., Inc. - All Rights Reserved.

REAR

CAMERA

HARNESS

VEHICLE

GROMMET

OPENING

DOWN

4709080K

YELLOW

WHITE

BLUE/BLACK

BLACK

BROWN

RED

YELLOW

WHITE

BLUE/BLACK

BROWN

BLACK

RED

LOCK

Viewed from harness side

6-PIN

CONNECTOR

RED

BLACK

6-PIN

CONNECTOR

6 TERMINALS

YELLOW

WHITE

BROWN

BLUE/

BLACK

57. Remove the lock from the 6-pin connector. Plug the rear camera harness terminals into the 6-pin connector as shown. Reinstall the lock.

58. Get the rear camera subharness. Plug the rear camera subharness 6-pin connector into the rear camera harness 6-pin connector, and secure the connected 6-pin connectors to the vehicle connectors with two wire ties.

VEHICLE

CONNECTOR

WIRE TIE

REAR CAMERA

HARNESS

6-PIN

CONNECTOR

REAR CAMERA

SUBHARNESS

6-PIN

CONNECTOR

FRONT

2 WIRE

TIES

VEHICLE

HARNESS

REAR CAMERA

SUBHARNESS

WIRE TIES

4712031K

AII 33263-38883 (0802)

15 of 18

59. Route the rear camera subharness forward along the vehicle harness, and secure the subharness to the vehicle harness with five wire ties.

60. Continue routing the rear camera subharness forward along the vehicle harness, and secure the subharness to the vehicle harness with four small wire ties.

DRIVER’S

SEAT

62. Plug the rear camera subharness 6-pin connector into the Navi control unit.

NAVI

CONTROL

UNIT

REAR CAMERA

SUBHARNESS

VEHICLE

HARNESS

FRONT

4712041K

SMALL

WIRE

TIES

61. Route the rear camera subharness along the vehicle harness and under the floor carpet, then pull the rear camera subharness out from under the floor carpet opening under the driver’s seat.

Secure the rear camera subharness to the vehicle harness with two wire ties.

DRIVER’S

SEAT

FLOOR CARPET

OPENING

REAR CAMERA

SUB HARNESS

6-PIN CONNECTOR

4713030K

63. Slide the driver’s seat back and forth to check that the rear camera subharness is not pulled too tight or is too loose.

DRIVER’S

SEAT

Check that the rear camera subharness is not pulled too tight when the seat is moved back and forth.

4713040K

16 of 18

WIRE

TIES

VEHICLE

HARNESS

REAR CAMERA

SUBHARNESS

4N10010K

AII 33263-38883 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved.

64. Reconnect the negative cable to the battery. Turn the key to the ON (II) position, and enter the Navi code.

2 WASHER SCREWS

4 x 6 mm

REAR

CAMERA

Adjust the angle.

REAR CAMERA

TRIM

68. Measure and mark the rear bumper at the location shown.

REAR

BUMPER

REAR CAMERA

BRACKET

5D10060T

4 x 10 mm

SOCKET BOLTS

65. Move the shift knob to the “R” position.

66. Loosen the two 4 x 6 mm washer-screws. Adjust the rear camera angle up or down so that the end of the rear bumper is reflected at the lowest possible end of the navigation monitor. Tighten the two 4 x 6 mm washer-screws. Install the rear camera trim to the rear camera bracket with two

4 x 10 mm socket bolts.

67. Turn the key to the off position.

10 mm

15 mm

3 mm

Cut off.

4N15011K

69. Using a utility knife, cut and remove measured piece from the rear bumper. Remove any burrs from the cut area with a file.

70. Reinstall the rear bumper.

71. Check that all wire harnesses are routed properly and all connectors are plugged in.

72. Enter the customer’s radio anti-theft code, and reset the radio station presets.

73. Set the clock.

74. Check the operation of the rear camera according to the owner’s manual provided.

75. Put the rear camera Owner’s Manual in the glove box with the vehicle owner’s manual.

76. Reinstall all removed parts.

NOTE: To reinstall the bed rail trim:

• With one hand on each end of the bed rail trim, hook the seven clips under the bed liner lip.

BED LINER LIP

CLIP

© 2008 American Honda Motor Co., Inc. - All Rights Reserved.

AII 33263-38883 (0802)

17 of 18

• Roll the trim toward the outside of the bed rail,

so the trim now lies flat on top of it and all six

lock tabs engage the slots in the bed rail.

Be sure all six lock tabs engage the slot on the pickup bed.

• With one hand on each end of the trim, push

down and slide it toward the cab until you feel

it stop. This locks all the tabs in place.

• Starting at the front end, press up on the edge of

the trim with your thumb to make sure it’s secure.

Then, working your way down the trim, repeat this

to ensure the other lock tabs and the clips are

secure.

NOTE: Whenever the battery is disconnected, the driver’s window AUTO function is disabled.

77. Start the engine. Push down fully on the driver’s window switch until the window is fully open.

78. Pull up fully on the driver’s window switch to close the window completely, then hold the switch for

2 second or more.

79. Test the window AUTO function.

Roll the trim toward the outside of the bed rail,

so the trim now lies flat on top of it and all six

lock tabs engage the slots in the bed rail.

18 of 18

AII 33263-38883 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved.