THE ENVIRONMENT

Always dispose of unwanted products, accessories and packaging materials in an environmentally friendly manner.

For EU and EEA countries only.

In observance of European Directive 2002/96/EC on Waste Electrical and Electronic

Equipment (WEEE) and its implementation in accordance with national law, electrical goods that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.

Do not dispose of electrical goods with domestic waste materials as inappropriate disposal may cause potential hazards to the environment and human health.

For further information, please contact your local authority or the retailer from whom you purchased the product.

Other EDISON products available are:

Calculators Cable ties Batteries Multimeters

AVAILABLE FROM YOUR DISTRIBUTOR

Torches

RECHARGEABLE

30 LED INSPECTION LAMP

ORDER CODE

EDI-904-1100K

MODEL ILR330

IMPORTANT NOTICE

CHARGE FULLY FOR

10 HOURS BEFORE INITIAL USE.

RECHARGE FULLY ONCE A MONTH

WHEN NOT IN USE.

IP68

Fully water and dust proof*

Will float to the surface if accidentally dropped in water

USES LITHIUM-ION

BATTERIES

Excellent energy to weight ratio

No memory effect

Slow loss of charge when not in use

High energy density

Edison Products are continuously being developed and improved. All details and illustrations are for guidance and may be subject to change.

E D I S O N

The Power Factory, PO Box 14,

Wigston, Leicester, England.

© EDISON 10/08

OPERATOR’S MANUAL

Please retain this information for future reference

SAFETY INSTRUCTIONS

• READ and understand fully the instructions before use.

• ONLY use the accompanied AC/DC charger to recharge the Inspection Lamp. The charger is suitable for indoor use only.

• NEVER block the lens and reflector during operation.

• NEVER look directly into the light or shine it in someone else’s eyes.

• NEVER allow children to use the Inspection Lamp.

• NEVER use the flashing light mode near people who have photosensitive epilepsy as it could trigger a seizure.

FEATURES

• Ideal for use in automotive workshops, the construction industry and other low light work areas

• Housed in a heavy duty rubber and polycarbonate case

• Lasts up to 6 hours when fully charged

• Adjustable brightness

• Durable, robust and reliable

• Fold-away swivel hanging hook

• Wall or bench mount charging base with

1.9m power cable

• 30 LEDs provide a constant high light output

• Water and oil resistant to IP68*

• Powered by high capacity lithium-ion polymer batteries

• Optional flashing mode

• Sealed switch

• Can be stood upright

• Uses induction charging technology

• Battery low warning

* Lamp only. The charger is for indoor use only.

SPECIFICATIONS

Charging time: . . . . . . . . . . . . . . . .4 hours

Operating time: . . . . . . . . . . . . . . . .6 hours

Operating temperature: . . . . . . .0

°C to 40°C

Battery: . . . . . . . . . . . . . . .3.7V 2,000mAh

. . . . . . . . . . . . . .

(Li-polymer lithium battery)

Charger: . . .230V AC - 14V DC 400mA 1.3W

LED intensity at 50cm: . . . . . . . . . .800Lux

Net weight (Inspection Lamp only): . . .345g

WALL MOUNTING THE CHARGER UNIT

ALWAYS MAKE SURE THAT YOU CHECK FOR HIDDEN PIPES AND WIRING BEFORE

DRILLING INTO A WALL.

N.B. Screws and wall plugs are not included with this product.

The charging unit can be easily wall mounted. Drill two holes, 72mm apart in the wall and insert wall plugs if required. Screw in two round headed screws into the wall leaving a 2mm gap between the screw heads and the face of the wall. Place the back of the charging unit against the wall so that the two screw heads locate into the two holes of the charging unit. Try sliding the charging unit down and adjust the screws if needed to obtain a secure fit.

72mm between the centre of the two holes

2

CHARGING

CHARGE THE BATTERY FOR 10 HOURS BEFORE INITIAL USE.

WHEN IN USE, ALL 30 LEDs WILL FLASH ON AND OFF 3 TIMES TO WARN THAT THE

INSPECTION LAMP WILL SOON NEED RECHARGING.

WHEN ONLY THE RED LED NEXT TO THE ON/OFF SWITCH COMES ON, THE INSPECTION

LAMP NEEDS CHARGING.

THE INSPECTION LAMP WILL NOT WORK WHILST IT IS BEING CHARGED.

RECHARGE FULLY ONCE A MONTH WHEN NOT IN USE.

Switch off the Inspection Lamp. Place the Inspection Lamp upright into the charging unit facing any direction. Plug in the charging unit and switch on the power.

• When the red LED next to the ON/OFF switch and the green LED on the front of the charging unit are constantly on, charging of the battery is taking place.

• When the red LED switches off, charging is complete.

OPERATION

THE LIFE OF THE INSPECTION LAMP BATTERY CAN BE EXTENDED IF IT IS FULLY

DISCHARGED BEFORE RECHARGING.

• LIGHT

Press the ON/OFF button once.

• FLASHING LIGHT

Press the ON/OFF button twice.

• ADJUSTING BRIGHTNESS

Press and hold down the ON/OFF button.

• HANDS FREE USE - SUSPENDING

DO NOT PULL EXCESSIVELY ON THE INSPECTION LAMP WHILST IT IS SUSPENDED.

MAKE SURE THAT THE INSPECTION LAMP WILL BE HELD SECURELY WHEN IT IS

SUSPENDED.

To suspend, pull the hanging hook which is positioned at the top of the Inspection Lamp upwards. When the Inspection Lamp is hanging from its hook, it can be rotated through

360

° for more precise positioning.

• HANDS FREE USE - TILTING

The Inspection Lamp can be placed on a flat surface and the hanging hook used to tilt it so that the light will be directed upwards. See figure 1.

1.

3