Black & Decker GD300 X Lawn Raker User Manual

UK
Ireland
Australia
New Zealand
2
3
Intended use
Your Black & Decker lawnraker has been designed for
raking lawns to remove debris, thatch, moss and weeds
which can disfigure a lawn. This tool is intended for
consumer use only.
Safety instructions
Warning! When using mains-powered appliances, basic
safety precautions, including the following, should always be
followed to reduce the risk of fire, electric shock and
personal injury.
X
Read all of this manual carefully before operating the
appliance.
X
Before operating the appliance, make sure that you
know how to switch it off in an emergency.
X
Retain this manual for future reference.
Training
X
Read the instructions carefully. Be familiar with the
controls and the proper use of the appliance.
X
Do not allow children or any person unfamiliar with
these instructions to operate the appliance. Local
regulations may restrict the age of the operator.
X
Never use the appliance while people, especially
children, or pets are nearby.
X
Remember that the operator will be held responsible for
accidents or hazards occurring to other people or their
property.
Preparation
X
Wear stout shoes or boots to protect your feet. Do not
operate the appliance wearing open-toed sandals or
when barefoot. Wear long trousers to protect your legs.
X
Wear safety glasses or goggles when operating this
tool. Use a face or dust mask whenever the operations
take place in dusty surroundings. Hearing protection
should be worn whenever the sound level seems
uncomfortable.
X
Guard against electric shock. Prevent body contact with
earthed or grounded surfaces (e.g. metal railings,
lampposts, etc.).
X
Before starting the operation, check that your raking
path is free from sticks, stones, wire and any other
objects.
Operation
X
Never operate the appliance with defective guards or
shields, or without safety devices, for example
deflectors and/or grass catchers, in place.
X
Only use the appliance in daylight or good artificial light.
4
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Do not expose the appliance to rain. Do not use the
appliance in damp or wet conditions. Preferably do not
use the appliance in wet grass.
Be sure of your footing, particularly on slopes. Be aware
that freshly cut grass is damp and slippery. Do not work
on steep slopes.
Work across the face of slopes, never up and down.
Take extreme caution when changing direction on
slopes.
Walk, never run when using the appliance. Do not pull
the appliance towards you or walk backwards when
using the appliance.
Switch on the appliance according to instructions and
with your feet well away from the tines.
Do not tilt appliance when switching it on, except if the
appliance has to be tilted for starting. In that case, do not
tilt the appliance more than absolutely necessary and lift
only the part that is away from the operator. Always
ensure that both hands are in the operating position
before returning the appliance to the ground.
Switch off the appliance and wait for the tines assembly
to stop running if the appliance has to be tilted for
transportation when crossing surfaces other than grass,
and when transporting the appliance to and from the
area to be raked.
Do not lift or carry the appliance until the tines have
come to a complete standstill.
Keep your hands and feet well away from the tines. Do
not put your hands or feet near or under rotating parts.
Keep away from discharge openings at all times.
Switch off, remove the plug from the socket and ensure
that moving parts have stopped rotating before leaving
the appliance unattended and before changing,
cleaning or inspecting any parts of the appliance or
clearing a blockage.
If the appliance starts to vibrate abnormally or if you hit
a foreign object, switch the appliance off and remove
the plug from the socket. Check for any damage to the
appliance.
Take care to keep the mains cable away from the tines.
Always be aware of the position of the cable.
The motor will continue to run for a few seconds after
switching the appliance off. Never attempt to force the
tines to come to a standstill.
Maintenance and storage
X
Before use, check the appliance for damaged or
defective parts. Check for misalignment and seizure of
moving parts, breakage of parts, damage to guards and
switches and any other conditions that may affect its
operation. Ensure that the appliance will operate
properly and perform its intended function. Never use
X
X
X
X
X
X
the appliance when any guard or enclosure is damaged
or not in place. Do not use the appliance if any part is
damaged or defective. Do not use the appliance if the
switch does not turn it on and off. Have any damaged or
defective parts repaired or replaced by an authorised
repair agent.
Check the cable frequently for damage. If the cable is
damaged, it must be replaced by an authorised repair
agent in order to prevent a hazard. Inspect extension
cables periodically. Replace a damaged extension
cable immediately.
Keep all nuts, bolts and screws on the appliance tight to
ensure a safe working condition.
Check the grass box for wear or damage and replace it
if necessary. Never use the appliance without the grass
box.
When not in use, the appliance should be stored in a dry
place. Children should not have access to stored
appliances.
Ensure that only replacement cutting means of the right
type are used.
Use only Black & Decker recommended spare parts and
accessories.
Additional safety instructions for Australia and New
Zealand
X
This appliance is not intended for use by young or infirm
persons without supervision. Children must be
supervised to ensure they do not play with the
appliance.
X
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Warning symbols
The following warning symbols are found on the appliance:
Read the manual prior to operation.
Do not expose the appliance to rain or high
humidity.
Keep bystanders away.
Beware of the sharp tines. Tines continue to
rotate after the motor is switched off - remove plug
from mains before maintenance or if the cord is
damaged.
Keep the cable away from the cutting tines.
The tines will continue to rotate after the machine
is switched off.
Electrical safety
X
X
This tool is double insulated; therefore no earth
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard
Electric safety can be further improved by using a highsensitivity 30 mA residual current device (RCD).
Extension cables & class 1 product
X
A 3 core cable must be used as your tool is earthed and
of class 1 construction.
X
Up to 30m (100 ft) can be used without loss of power.
X
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
1. Grass box
2. Motor cover
3. Switch box
4. Lock-off button
5. Switch lever
Assembly
Warning! Before assembly, make sure that the appliance is
switched off and unplugged.
Assembling the upper handle (fig. A)
X
Make sure that the cable restraint loop is fitted to the
upper handle prior to assembly.
X
Fit the lower handle part (7) to the upper handle (6)
using the knobs (10), washers (9) and screws (8) as
shown.
5
mow them. The sweep/light rake setting is ideal for
fallen leaves and for collecting grass cuttings which
have been left on the lawn after mowing.
Fitting the lower handle (fig. C)
X
Insert the ends of the lower handle (7) into the
corresponding holes in the raker.
X
Press the handle down as far as it will go.
X
Secure the handle using the screws (12).
Use
Fixing the cable (fig. B)
Switching on and off
The motor cable has to be fixed using the cable restraints.
X
Clip the one restraint (11) onto the cable leading from
the switchbox (3) to the motor. Secure the restraint to
the lower handle (7).
X
Clip the other restraint (11) onto the cable leading from
the switchbox (3) to the motor plug. Secure the restraint
to the upper handle (7).
Warning! Make sure the cable is secured using the cable
restraints prior to connecting the plug to the mains outlet.
Switching on
X
Hold the handle with both hands and tilt it slightly
downwards to raise the front of the appliance.
X
Press the lock-off button (4) and pull the switch lever (5)
towards you.
X
Release the lock-off button (4).
X
Let the appliance return to its working position.
Fitting the cable storage holders (fig. F)
The cable holders (14 and 15) provide a safe and convenient
way to store the cable when not in use.
X
Clip the two cable holders (14 and 15) to the lower
handle (7) as shown (fig. F)
Fitting the grass box (fig. D)
X
With your lawnraker in its working position, place the
grass box (1) over the lugs at the front of the lawnraker.
Height of rake adjustment (Fig. E)
There are three raking height positions on your raker; low,
medium and high. These are selected by altering the
position of the three-position height adjuster located on the
rear roller (13).
X
Press the lock button on the three-position height
adjuster and rotate the adjuster to any of the three
available positions as shown in Fig. E. On reaching the
required position, release the lock button and allow it to
engage in your raker body (2).
X
The three positions are identified by markings on the
side of your raker body as shown in Fig. E.
The three raking height positions are as follows:
X
Lowest setting (1). This setting should be used when
you wish to give the lawn a particularly vigorous raking.
On this setting, your raker will remove all the debris and
thatch that has collected at the base of your grass. It will
also remove moss and weeds on this setting.
X
Medium setting (2). This setting should be used when
you wish to give your lawn a moderate raking. This
setting will be suitable for the majority of lawns.
X
Highest setting (3). This setting will lightly rake and
sweep your lawn. Your raker can also be used on this
setting to ‘lift’ flattened grass and stolons (the creeping
stems of grasses and weeds like clover) so that you can
6
Switching off
X
To switch the appliance off, release the switch lever (5).
Never attempt to lock a switch in the on position.
Warning! Let the appliance work at its own pace. Do not
overload.
To look after a lawn properly, you need to do more than just
mow it once a week throughout the Summer. The lawn will
benefit from a vigorous raking of the grass to remove the
dead matter, moss and weed which disfigures a lawn. The
build up of dead grass provides a mat of absorbent fibres
which prevents water getting through to the ground and if
this mat is kept waterlogged, it can encourage grass
diseases and prevent healthy grasses taking root.
X
Place the bulk of the extension cable on the lawn close
to the starting point (Fig. G, position 1).
X
Hold the handle with both hands and hold the upper
portion of the extension cable in the hand not operating
the switch lever.
Warning! Do not attempt to operate your raker with one
hand - you must guide it with both hands.
X
Switch on as described above.
X
Proceed down the raking area from position 1 towards
position 2 and, on reaching position 2, turn to the right
and proceed towards position 3. Continue to the end of
the raking area, turn to the left, and proceed towards
position 4.
X
Continue in the same manner as shown in the left hand
diagram, always working away from the cable. Do not
adopt the method shown in the right hand diagram,
working towards the cable, as this is dangerous
practice.
When you have finished using your raker we recommend
that you clean all debris from it before putting it away. Refer
to the “Maintenance” section in this manual.
Note: To obtain the best results rake your lawn or grassed
area regularly and do not rake when the grass is wet.
When raking over the edge of your lawn, press
downwards on the handle to stop the wheels dropping
over the edge.
X
To prolong the effective raking life of your tine
assembly, clear the lawn area of any loose debris or
stones.
Warning! Do not connect a damaged cord to the supply or
touch a damaged cord before it is disconnected from the
supply. A damaged cord can lead to contact with live parts.
Warning! Do not touch the tines before the machine is
disconnected form the supply and the tines have come to a
complete stop.
Warning! Children should be supervised to ensure that they
do not play with the appliance.
Warning! This appliance is not intended for use by persons
(including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
the use of the appliance by a person responsible for their
safety.
X
Hints for optimum use
Do not force your raker through grass that is too long. It is
recommended that your raker should not be used in grass
that is longer that 75mm (3 inches) in length.
X
Do not use in wet or damp conditions.
X
To obtain the best result from your raker use it regularly.
It is recommended that your raker is used at the
beginning and end of each grass cutting season to give
your lawn a thorough scarifying. Your raker should also
be used after each mowing session to remove any
grass cuttings that may have been left behind by your
raker.
X
Rake first in one direction and then at the next occasion
at right angles. Initially, this may make the grass look
bare and straggly but it will rapidly recover.
Maintenance
Your Black & Decker appliance has been designed to
operate over a long period of time with a minimum of
maintenance. Continuous satisfactory operation depends
upon proper appliance care and regular cleaning.
X
Keep the appliance clean and dry.
X
Regularly clean the ventilation slots with a clean, dry
paint brush.
X
Regularly use a blunt scraper to remove grass and dirt
from the appliance.
X
To clean the appliance, use only mild soap and a damp
cloth. Never let any liquid get inside the tool and never
immerse any part of the tool into liquid. Do not use any
abrasive or solvent-based cleaner.
Troubleshooting
If your appliance seems not to operate properly, follow the
instructions below. If this does not solve the problem, please
contact your local Black & Decker repair agent.
Warning! Before proceeding, remove the plug from the
socket.
Motor buzzes but the tine assembly does not move
X
Carefully remove any obstructions from the tines.
No noise and tine assembly does not move
X
Check that the power cables are properly connected.
X
Check the mains fuses.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
X
Safely dispose of the old plug.
X
Connect the brown lead to the live terminal in the new
plug.
X
Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality
plugs. Recommended fuse: 13 A.
Protecting the environment
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again. Reuse of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
Black & Decker provides a facility for the collection and
recycling of Black & Decker products once they have
reached the end of their working life. To take advantage of
this service please return your product to any authorised
repair agent who will collect them on our behalf.
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at the
address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of
our after-sales service and contacts are available on the
Internet at: www.2helpU.com.
7
Technical data
X
Voltage
Power input
No-load speed
Height adjustment
Weight
Vac
W
min-1
cm
kg
GD300
230
600
3000
-2/3/8
7.9
GD300X
230
500
3000
-2/3/8
7.9
EC declaration of conformity
GD300, GD300X
Black & Decker declares that these products conform to:
98/37/EC, EN 60335, 2000/14/EC
Scarifier. 600 W, Annex V
LpA (sound pressure) 71 dB(A),
LWA (acoustic power) 98 dB(A),
hand/arm weighted vibration <2.5 m/s2
Kpa (sound pressure uncertainty 3 dB(A),
Kwa (sound power uncertainty 3 dB(A),
2000/14/EC, Annex V1, No 0197
Notified body TUV Rheinland
The undersigned is responsible for compilation of the
technical file and makes this declaration on behalf of
Black & Decker
Kevin Hewitt
Director of Consumer Engineering
Spennymoor, County Durham DL16 6JG,
United Kingdom
18-11-2007
Guarantee
Black & Decker is confident of the quality of its products and
offers an outstanding guarantee. This guarantee statement
is in addition to and in no way prejudices your statutory
rights. The guarantee is valid within the territories of the
Member States of the European Union and the European
Free Trade Area.
If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 24
months from the date of purchase, Black & Decker
guarantees to replace defective parts, repair products
subjected to fair wear and tear or replace such products to
make sure of the minimum inconvenience to the customer
unless:
X
The product has been used for trade, professional or
hire purposes.
X
The product has been subjected to misuse or neglect.
8
X
The product has sustained damage through foreign
objects, substances or accidents.
Repairs have been attempted by persons other than
authorised repair agents or Black & Decker service
staff.
To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent by
contacting your local Black & Decker office at the address
indicated in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our aftersales service and contacts are available on the Internet at:
www.2helpU.com
Please visit our website www.blackanddecker.co.uk to
register your new Black & Decker product and to be kept up
to date on new products and special offers. Further
information on the Black & Decker brand and our range of
products is available at www.blackanddecker.co.uk.
9
10
11
$XVWUDOLD
%ODFN'HFNHU$XVWUDOLD3W\/WG
)OHWFKHU5RDG0RRURROEDUN
9LFWRULD
1HZ=HDODQG
%ODFN'HFNHU
7H$SXQJD3ODFH
0W:HOOLQJWRQ
$XFNODQG
8QLWHG.LQJGRP
%ODFN'HFNHU
%DWK5RDG
6ORXJK%HUNVKLUH6/<'
90524006
7HO
)D[
7HO
)D[
7HO
)D[
+HOSOLQH
11/07