Reporter Wireless Reporter 502 Wireless Intercom, Oracle Gate System User Manual

Model#: 502 03/29/07
Patents pending
(This Page Intentionally Left Blank)
Thank you for purchasing
the Reporter Wirefree
Intercom
Wall
Flush
Mount Unit. This product
has been designed and
manufactured in the USA,
utilizing the highest quality
standards available.
Wall Flush-Mount Design
(Model#: 502)
The Reporter™ Wirefree
Intercom
features
an
amazing 1000’ range, and
allows multiple simultaneous
conversations, using a 900
MHz secure digital radio link.
allo
For privacy, your intercoms
form an exclusive network,
and respond only to other
intercoms in your network.
(Patent Pending)
System Features:
•
Easily install in drywall for a “Built-in”
look. This brand new design features
extended,
through-wall
technology,
easily covering the largest home and
business locations.
• “C” Batteries operate the unit for up to
3 years.
• Multi-Channel with digital secure
connection.
• Unlimited number of units can operate
in a dwelling, without mixing with the
next-door dwelling.
• Network wide conference mode
Even conversations within
your network are secure, as
intercoms automatically pair
up,
blocking
all
other
intercoms from listening in.
Since this intercom system
requires no connection to
wall power, it is perfect for
the do-it-yourself installer.
Please read the instructions
carefully.
Note: This unit is recommended for
indoor use only.
Made With Pride In the USA. This product is covered by a
manufacturer’s full One Year Warranty.
FCC STATEMENT
This device complies with FCC part 15 rules. It may not cause harmful interference with other devices, and must accept interference from other devices.
FCC ID: JLFTRX
Setting Up the Intercom
Installation
Choose a wall location
that is free of beams
and other obstructions
inside the wall. Mount
the intercom at a
convenient height for
easy use, typically
shoulder height.
Cut a hole in the wall measuring 6 1/8” wide
by 4 1/2” high. Insert each of the four screws
through a corner of the frame and into a
plastic fastener. Screw in only about 1/4” into
each plastic fastener - do not tighten.
Place the frame in the hole. With a large
screwdriver, tighten the screws until the selfaligning fasteners rotate and tighten to firmly
hold the frame in place.
Install
four
‘C’
batteries
in
the
Intercom’s
battery
pack (the LEDs will
illuminate). Clip this
unit into the frame by
inserting
the
top
section first and then
the lower half (as
shown in the picture).
This unit is now ready
to be taught to the
Reporter intercoms in
the network.
Creating an Intercom Network with
Wall Mount and/or Portable Units.
The Intercom units must be taught to each
other to form an intercom network. The Wall
Mount unit is fully compatible with other Flush
Mount Reporter Intercom units, as well as the
Reporter WireFREE Portable units.
To create a new network of intercoms, place
each Wall Mount Intercom in Learn mode by
holding down both buttons for 3 seconds. The
LEDs will flash rapidly. Within 10 seconds, put
any other Wall Mount intercom units in learn
mode by holding down the same two buttons
(or single button for the portable unit). Each
intercom will produce a tone as it joins the
network. Note: One unit may produce a
different tone. This is normal.
To add an additional intercom unit to an
existing network, put both the new
intercom and one of the networked
intercoms in learn mode by pushing both
buttons on each unit for 3 seconds. The
new unit will join the network.
Channel Selection
The default channel
for the intercom is the
Paging Channel. All four
channel lights will flash
in sequence. Press the
CHANNEL button to set
an intercom unit to one
of four secure channels
or the paging channel.
While on a channel, you
can only be heard by
other units set to the
same channel or the
paging channel.
Using the Intercom
To talk, hold down the TALK button.
Every intercom unit in the network on
the same channel will receive the signal.
Release the TALK button when you are
finished talking. When someone responds
to you within 10-15 seconds by holding
down the TALK button on a different
intercom unit, a secure connection is
created. Other units will not receive the
signal.
Troubleshooting and Frequently Asked Questions
Nothing Happens. The Intercom Does Not Function
It is normal for the lights to go out if the Wall Mount Intercom has been inactive for
five minutes. The lights should illuminate again after a button is pressed or a signal is
received. If the unit does not operate, check the batteries. Normally, the CHANNEL
lights should flash, showing the channel that the unit is set to. If the units have power
and are not working, they may need to form a network. Press the LEARN buttons on the
units that need to be introduced and they will beep in response. You may need to clear
their memory (see below), AND THEN teach them.
If the units are not on the same channel, press the CHANNEL button until both units
are on the same channel or in Paging mode, with all channel lights illuminated.
The Intercom is Not Getting the Expected Transmission Range
Trees, metal, electrical wiring or other electrical devices directly between units can
limit the range, as can having it mounted within is few inches of electrical wiring.
There is a Double Beep every Ten Minutes
The intercom is indicating that the batteries are low and need to be replaced.
How do I Clear the Intercom’s Memory to Remove it from a Network
Press and hold both buttons for 20 seconds. A tone will indicate that the unit has
cleared its memory and you can re-teach it to a new intercom. If an intercom signals,
while the buttons are depressed, the procedure will have to be repeated.
I hear Static and Feedback through the Intercom
The intercom is probably too close to another intercom. Once the intercom is installed
in the desired location, it will operate normally. If a cordless phone, cell phone, or other
radio device is too close to the intercom, it can generate static or limit the range.
Adjusting the speaker volume
The volume can be adjusted by holding
down the TALK button and repeatedly
pressing the CHANNEL button to cycle
through three volume levels.
Conference Mode
All Intercoms must be set on the same
channel or the paging channel to
participate in the Conference.
To place Intercoms in the Conference
Mode, slide dipswitch #3 (sw3) UP on all
Wall Mount intercoms and dipswitch #2
Up on Portable units in the network.
Oracle Gate System Compatible
If you receive a CALL from the Oracle
Gate System, the Wall Mount intercom
buttons will illuminate. TALK will open
an audio channel; REMOTE will open the
gate. See the Oracle Gate System manual
for further information.
NOTE: The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modifications to this equipment. Changes or
modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
If you have installation or operation questions, please see above, or check out the expanded FAQ at the
manufacturer’s web page at www.reporterwireless.com. You can receive free technical assistance or
warranty service, by email at [email protected] or call 888.679.7994 Tuesday-Friday 8-5 PST
Warranty: This product is warranted to be free of defects for the period of One Year from the date of purchase.
The warranty
covers parts, labor, and return shipping to you, but not all accessories. IEI will repair or replace any defective product at our
discretion. Warranty does not cover misuse or damage other than due to normal operating conditions. If you need to send the
system to IEI for repair, contact IEI for a Return Authorization number via email: [email protected]. Packages without a
Return Authorization number will be rejected.