Read all instructions before assembly and use.

KEEP INSTRUCTIONS FOR FUTURE USE.

ADULT ASSEMBLY REQUIRED

Due to the presence of small parts during assembly, keep out of reach of children until assembly is complete.

Changing Table

THIS PRODUCT IS NOT INTENDED FOR

INSTITUTIONAL OR COMMERCIAL USE.

Conforms to

ASTM F2388

Safety Standards

Consumer Care:

www.DeltaChildren.com

Delta Children’s Products

114 West 26th Street

New York, NY 10001

Tele.212-645-9033

Style #:

Lot:

Date:

___________

___________

___________

B

REV

When contacting Delta Consumer Care please reference the above information. Before contacting Delta

Consumer Care please ensure that the information above matches the information found on the label on the Top Shelf, please reference the information found on the product when contacting Delta Consumer

Care.

To register your product for important safety alerts and updates to your product please visit www.DeltaChildren.com and click on Product Registration.

MAY 6, 2014, 24364, R1 ©2014 DELTA ENTERPRISE CORP.

WARNING

FALL HAZARD - to prevent death or serious injury, always keep child within arm’s reach.

Read all instructions before use of the changing table.

KEEP THESE INSTRUCTIONS IN A SAFE PLACE FOR FUTURE USE.

Inspect the changing table periodically. Do not use the changing table if it is damaged or broken. Contact Delta Children’s Products with any questions.

Tighten all loose screws and bolts before each use.

The maximum recommended weight of the child is 30lbs for the changing table.

Use only the pad provided by Delta Children’s Products.

NOTES ON ASSEMBLY:

-During the assembly process whenever using screws or bolts, check each by placing the screw/bolt on the diagram of the item which is drawn actual size and design. Be sure to use the proper size and shape specified in the instructions.

-To assemble this unit you may be required to place the unit on it’s side and face. It is strongly recommended that assembly is done on a soft, non-abrasive surface to avoid damaging the finish.

NOTES ON USE:

Keep children and others safe by following these simple rules:

- Do not allow any child to play on furniture

- Do not allow climbing on any piece of furniture.

- Do not allow hanging from any piece of furniture.

- Always monitor your child’s activity when in the nursery.

NOTES ON CARE AND MAINTENANCE:

- Do not scratch or chip the finish.

- Inspect the product periodically, contact Delta Children's Products for replacement parts or questions.

- Do not store the product or any parts in extreme temperatures and conditions such as a hot attic or a damp, cold basement. These extremes can cause a loss of structural integrity.

-To preserve the luster of the high quality finish on your product, it is recommended to place a doily or felt pad under any items you place on the finish.

-Clean with a damp cloth, then a dry cloth to preserve the original luster and beauty of this fine finish.

Do not use abrasive chemicals.

Do not spray cleaners directly onto furniture.

-Lift slightly when moving on carpeting to prevent leg breakage.

-Use of a vaporizer near furniture will cause wood to swell and finish to peel.

2

PARTS:

MAKE SURE THAT ALL PRE-ASSEMBLED PARTS ARE TIGHT.

C. Back Top Rail x 1

Part # 24356

A. Left Side x 1

Part # 24354

B. Right Side x 1

Part # 24355

G. Top Shelf x 1

Part # 24360

H. Bottom Shelf x 2

Part # 24361

J. Changer Pad x 1

Part # 21282

D. Front Top Rail x 1

Part # 24357

E. Shelf Rail x 3

Part # 24358

F. Front Bottom Rail x 1

Part # 24359

K. Restraint Harness x 1

Part # 21748

3

PARTS:

HARDWARE KIT IS PART #24363-986 FOR COLOR 100 OR #24363-988 FOR

COLOR 205, 207, 604 AND 607 OR #24363-989 FOR COLOR 001.

SEE FRONT COVER.

L. M6 x 55 mm Bolt x 12

Part # 5468

M. M6 x 25 mm Bolt x 2

Part # 5462

No drills necessary.

Do not use power screwdriver.

Flat Head Screwdriver

(not supplied)

Pliers or Adjustable

Wrench Required for Assembly

(not supplied)

N. Nylon Washer x 4

Part # 5525

P. Nut x 2

Part # 4065

R. M6x17mm Barrel Nut x 12

5479

M4 Allen Wrench Supplied

Part # 1177

4

Section 1: Changing Table Assembly

Step 1

Parts and tools required to complete step.

C. Back Top Rail x 1

M4 Allen Wrench

Supplied

D. Front Top Rail x 1

R. M6x17mm Barrel Nut x 6

E. Shelf Rail x 3

A. Left Side x 1 F. Front Bottom Rail x 1 L. M6 x 55 mm Bolt x 6

Attach (1) Back Top Rail (Part C), (1) Front Top Rail (Part D), (3) Shelf Rails (Part E) and (1) Front

Bottom Rail (Part F) to the Left Side (Part A) with (6) M6x55mm Bolts (Part L) and (6) M6x17mm Barrel

Nuts (Part R) using the M4 Allen Wrench as shown. Use the Flat Head Screwdriver to hold the Barrel

Nut in the proper alignment. BE SURE THE GROOVES FACE TO THE INSIDE.

D

E

C

F

L R

A

L

R

L

E

L R

R

R

L

R

L

5

Section 1: Changing Table Assembly

Step 2

Parts and tools required to complete step.

G. Top Shelf x 1 H. Bottom Shelf x 2

From Step 1

Lay the Left Side on the floor, rails up. Slide the Top Shelf (Part G) in the grooves on the Front Top

Rail and Back Top Rail, into the groove on the Left Side, Slide (2) Bottom Shelves (Part H) in the grooves on the Shelf Rails and Front Bottom Rail, into the grooves on the Left Side as shown.

H

H

G

6

Section 1: Changing Table Assembly

Step 3

Parts and tools required to complete step.

From Step 2

M4 Allen Wrench

Supplied

R. M6x17mm Barrel Nut x 6

B. Right Side x 1 L. M6 x 55 mm Bolt x 6

Attach (1) Right Side (Part B) to the assembly from step 2 with (6) M6x55 mm Bolts (Part L) and (6)

M6x17mm Barrel Nuts (Part R) using the M4 Allen Wrench as shown. Use the Flat Head Screwdriver to hold the Barrel Nut in the proper alignment.

L

L B

L

L

L

L

R

R

R

R

R

R

7

Section 1: Changing Table Assembly

Step 4

Parts and tools required to complete step.

M. M6 x 25 mm Bolt x 2

P. Nut x 2

N. Nylon Washer x 4

M4 Allen Wrench Supplied

From Step 3

K. Restraint Harness x 1

Pliers or Adjustable

Wrench (Not Supplied)

Align the hole in the end of the strap of the Restraint Harness (Part K) with the hole in the Top Shelf.

Insert (1) M6x25 mm Bolts (Part M) through a Nylon Washer (Part N), the Restraint Strap and the hole in the Shelf. Add (1) Nylon Washer (Part N) with a Nut (Part P). Hold the Nut with a Pliers or Adjustable

Wrench. Repeat with the other side of the strap as shown.

N

M

N

P

K

8

Section 1: Changing Table Assembly

Step 5

Parts and tools required to complete step.

J. Changer Pad x 1

From Step 4

Place the Changer Pad (Part J) onto the Top Shelf (Part G) on top of the attached Strap from step 4,

Be sure the buckle on the strap is over the Pad as shown.

K

9

Section 1: Changing Table Assembly

Final

RESTRAINT HARNESS SYSTEM USE:

. PLACE THE INFANT ON THE CHANGING TABLE FOAM PAD.

. POSITION THE RESTRAINT HARNESS OVER THE MIDDLE OF THE INFANT’S

TORSO AND INSERT THE BUCKLED ENDS INTO EACH OTHER UNTIL THE LOCK

SHUT WITH A CLICK.

. GENTLY PULL THE LOOSE END OF THE STRAP TO LIGHTLY SNUG THE

RESTRAINT HARNESS AROUND THE INFANT.

MAINTENANCE

. CHECK FASTENERS PERIODICALLY FOR TIGHTNESS. DO NOT OVER TIGHTEN.

THIS MAY CAUSE DISTORTION OR BREAKAGE.

WARNING : FALL HAZARD

ALWAY KEEP CHILD WITHIN ARMS REACH.

TO FASTEN STRAP - PUSH BUCKLE SIDE TOGETHER

BE SURE BUCKLE IS FULLY FASTENED TO

SECURE CHILD SAFELY

TO RELEASE PRESS BOTH TABS AND PULL APART

10

Consumer Care:

www.DeltaChildren.com

Delta Children’s Products

114 West 26th Street

New York, NY 10001

Tele.212-645-9033

Warranty:

This Delta product is warranted to be free from defects for a period of 90 days from the date of purchase under normal use. This warranty extends only to the original retail purchaser and is valid only when supplied with proof of purchase, or if received as a gift, when the registration is on file with Delta.

To register your product for important safety alerts and updates to your product please visit www.DeltaChildren.com

Please do not return this item to the store before contacting us about missing parts or with any questions.

To report a problem, please log on to www.DeltaChildren.com and click the Consumer Care Tab, or contact us by phone at

(212) 645-9033.

In the event that you need to contact our customer service department please have the Style Number and Lot Number available.

Use the space below to make note of those numbers. They can be found on the label on the Top Shelf.

STYLE No: 7530

B

REV FTY COLOR

Lot No. : _______________________

Pack Date:_____________________

Date of Purchase: _____________ (you should also keep your receipt)