IceAge  II  

Professional  Ice  Maker  

„AP-­‐01A“  

INSTRUCTION  MANUAL  

Thank you for purchasing the Ice Factory.

Please  read  this  instruction  thoroughly  before  your  first  use   of  this  product.  Keep  this  manual  carefully  for  future  use.  

Product Description

1.  The  BT-­‐25BTS  Ice  Factory  is  a  elegant,  portable,  well-­‐designed  ice  maker.  

2.  It’s  micro  computerized  system  makes  the  whole  process  of  ice  cube  making  completely  automatic.  BT-­‐25BTS  is  designed  for  using   external  water  inlet  pipe  for  water  supply,  and  as  well  for  manual  water  filling.  

3.  The  advanced  “ZEL”  compressor  and  cooling  system  can  product  ice  cubes  in  high  speed  and  good  quality.  Daily  ice  cubes  

  production  is  max.  20  Kg.  

4.  Three  different  size  of  solid  ice  cube  are  available  for  selection  

5.  Its  Intelligent  System  keeps  all  ice  cubes  in  consistent  size  by  adjusting  the  duration  of  ice  cube  making  process  automatically   according  to  room  temperature.  

6.  This  unit  are  equipped  with  self-­‐defected  detector  and  protective  devices.  

7.  Its  unique  design  and  portability  can  complement  you  at  Bar,  Party  Gathering,  Yachts,  Office  or  wherever  you  need.  

Technical Specifications

MODEL:      

VOLTAGE:    

FREQUENCY:    

POWER:      

CLIMATE:      

INSULATION  FOAMING:    

BT-­‐25BTS  DIELECTRIC  PROTECTION  CLASS:  I  

220-­‐240V~  RATED  CURRENT:  1.3A  

50Hz  REFRIGERANT/CHARGE:  R134A/110g  

200W  ICE  MAKING  CAPACITY:  max.  20kg/day.  

N.ST  WATER  INLET  PRESSURE:  0.1MPa  -­‐  0.3  Mpa  

POLYURETHANE  

Parts Diagram

1:  Water  Tank  

2:  Ice  Cube  Tray  

3:  Ice  Baffle  

4:  Ice  Maker  

5:  Control  Panel  

6:  Switch  Panel  

7:  Water  Inlet  Valve  

8:  Tap  Water  Connector  

9:  Lip  Cover  

10:  Compressor  

11:  Water  Pump  

12:  Condenser  

13:  Evaporator  

14:  Thermo  Sensor  

15:  Mini  Water  Level  Sensor  

16:  Maximum  Water  Level  Sensor  

Control Panel Diagram

1 2 3

•

Power On Indicator

•

Ice Full Indicator

•

Low Water Indicator

•

Power ON/OFF Button

4

Enclosed Accessory

Instruction  Manual  &  Ice  Shovel  (3  sets)  

How to use

1.  Remove  all  packaging  materials  and  labels.  Keep  the  unit  at  up-­‐right  position  while  lifting  up  from  the  packaging  to  avoid  causing   damage  to  the  compressor  of  the  unit.  The  tilt  angle  can  not  greater  than  45  Degree.  

2.  Place  the  Ice  Station  at  up-­‐right  position.  Keep  the  unit  at  least  20CM  apart  from  the  wall  around  for  better  ventilation  and  

  operation.  

3.  Wash  the  Water  Tank;  Cooling  System,  Ice  Cube  Tray;  Ice  Shovel  of  the  Ice  Station  with  washing  detergent  before  each  use.  

4.  Open  the  Lip  Cover,  fill  the  Water  Tank  with  drinking  water.  When  adding  water,  make  sure  the  water  level  does  not  exceed  the   maximum  water  level  of  the  Water  Tank.  If  you  use  the  external  Water  Pipe  for  adding  water,  make  sure  the  Water  Pipe  is  firmly  

  connected  with  the  In  Coming  Water  Inlet,  open  the  tap  and  check  to  ensure  no  water  leaking  in  the  conjunction  part  before  use.  

5.  External Water Inlet Installation diagram

Water  Inlet  Connector  Water  Pipe   Valve   3  way  water  connector  

Caution:  When  using  external  water  source,  be  sure  to  use  a  water  pressure  reducer!  

6.  Plug  in  the  unit  to  the  power  outlet,  the  Power  On  Indicator  will  light,  indicating  that  the  machine  is  in  standby  status.  

7.

Control Panel Diagram

Power  On  Indicator  

Ice  Full  Indicator  

Lack  Water  Indicator  

Power  On/Off  Button  

Select  Button  (  Ice  Cube  Size  )  

8.  Press  the  “Power  On/Off”  button  in  the  Control  Panel  to  “On”  position  to  start  the  operation.    

During the operation, press the “Power On/Off” button to “Off” position to stop the unit from running.

9.  After  the  unit  running  for  few  minutes,  the  temperature  of  the  unit  and  water  starts  dropping,  as  the  flowing  water  temperature  

  reach  zero  degree,  the  water  become  frozen,  the  indicated  size  will  blink.  Ice  cubes  making  are  now  in  progress.  

10.  36  pieces  of  ice  cubes  will  fall  into  the  Ice  Cube  Tray  automatically  for  each  cycle.  Once  all  ice  cubes  are  shoveled,  the  ice  cube   making  cycle  starts  again.  

11.  When  the  Ice  Cube  Tray  is  full,  the  “Ice  Full”  Indicator  will  blink,  the  compressor  and  fan  motor  will  stop  running.  Remove  the  ice  

  cubes  from  the  Ice  Cube  Tray.  The  same  Ice  cube  making  cycle  will  starts  again.  

Duration  of  ice  cube  making  apprx.  12-­‐18  minutes  

Maintenance

1.  Always  keep  the  unit  stand  still  at  up-­‐right  position  while  moving  to  avoid  causing  damage  to  the   compressor  of  the  unit.  

2.  Plug  the  unit  into  a  power  outlet  alone.  Make  sure  your  electricity  supply  is  187-­‐242V~50Hz,  the  

  current  is  10A.  

3.  To  disconnect  the  power,  grip  the  plug  and  pull  it  from  the  wall  outlet.  Never  drag  the  cord.  If  the   power  cord  is  damaged,  bring  it  to  the  service  centre  for  replacement.  

4.  The  unit  should  be  placed  vertically.  Do  not  place  the  unit  near  flammable  items  or  fire  source.  

Keep  at  least  20cm  distance  from  the  surroundings  for  better  ventilation  and  operation.  

5.  Initially  when  switching  “On”  the  unit,  it  will  takes  sometimes  before  water  is  cooling  down  to  zero   degree.  Duration  of  ice  cube  making  will  be  prolonged  if  adding  more  water.  

6.  If  the  water  level  is  lower  than  the  minimum  water  level  of  the  Water  Tank,  the  “Lack  Water”   indicator  will  light,  indicating  manual  water  filling  is  required.  If  using  external  water  inlet  pipe  for   water  supply,  the  “Lack  Water”  indicator  will  blink,  indicating  water  filling  starts  automatically.  

7.  Use  only  drinking  water  to  make  the  ice  cube.  Never  use  dirty  water  as  it  may  damage  your  health.  

Clean  the  unit  frequently  after  each  usage.  

8.  Clean  the  water  ejector  if  water  is  not  flowing  well.  

9.  Install  the  “Ice  Cube  Tray”  in  correct  position  to  avoid  touching  the  Ice  Shovel  

10.  If  no  water  is  adding  to  the  unit  when  the  “Lack  water”  indicator  light  up,  the  unit  will  stops  running   automatically.  

11.  Always  keep  the  sensors  clean  from  rust  for  better  performance.  

12.  Do  not  open  the  Lip  Cover  of  the  unit  during  running  as  it  may  affects  the  ice  cubes  making  performance.  

13.  Unplug  the  unit  from  the  power  outlet  and  remove  all  ice  cubes  before  cleaning.  Use  a  dilute   solution  of  water  and  vinegar  to  clean  the  interior  of  the  ice  maker,  and  then  rinse  it  with  drinking   water  thoroughly.  Do  not  rinse  internal  components  of  this  unit.  Do  not  use  gasoline  to  wash  this  

  unit.  

14.  Remove  the  Drain  Plug  from  the  unit  to  drain  the  remaining  water  from  the  water  tank  and  let  it   clean  and  dry  when  the  unit  will  not  be  used  for  a  long  period.  

15.  When  using  the  external  water  pipe  for  water  supply,  the  unit  will  stops  running  if  there  are  no   water  supply  coming  from  the  pipe.  

Trouble Shooting

Before  bringing  to  the  service  centre,  please  check  the  followings:  

Problems

The  compressor  makes   some  unusual  noise  when   the  “Power  On  Indicator”   is  “On”  

Possible Reasons

Incorrect  power  supply.

The  “Power  On  Indicator”   does  not  light  

–  No  power  supply  

–  Bad  contact  with  the   power  outlet  

Solution

Unplug  the  unit,  and  check  to  ensure   correct  power  supply  is  used.  

Check  both  the  power  cord,  power   plug  and  power  outlet  

The  “Ice  Full  Indicator”   keeps  on  blinking

Ice  Baffle  are  blocked  by   ice  cubes.  It  can  not  

  works  properly  

Remove  the  ice  cubes,  turn  off  the   ice  maker.  And  then  turn  on  again  

NOTE: Please contact our service centre for replacement if problems are not caused by the above reasons.

The unit is in normal good condition if the following occurred

•  The  fan  is  still  running  for  few  seconds  after  switching  “Off”  the  unit  and  the  compressor.  

•  Noise  caused  by  the  running  compressor  and  the  flowing  refrigerant  inside  the  compressor.  

BETEC ·  Herzogstr.  55  ·  D-­‐63263  Neu-­‐Isenburg

Phone  +49  (0)  61  02  /  310  67  ·  Fax  +49  (0)  61  02  /  32  08  59   www.BETEC-­‐Ideen.de  ·  E-­‐mail:  info@BETEC-­‐Ideen.de  

© BETEC

Art.Nr./Part-­‐No.  4046