Flex-a-lite Wrangler JK Jeep Radiator Wrangler JK, Jeep Radiator Wrangler JK Hemi Swap radiator, Wrangler JK Jeep Radiator/Fan Wrangler JK, Jeep Radiator/Fan Wrangler JK Hemi radiator/fan Instructions

Flex-a-lite Wrangler JK Jeep Radiator Wrangler JK, Jeep Radiator Wrangler JK Hemi Swap radiator, Wrangler JK Jeep Radiator/Fan Wrangler JK, Jeep Radiator/Fan Wrangler JK Hemi radiator/fan Instructions

Below you will find brief information for radiator Wrangler JK Jeep Radiator Wrangler JK, radiator Wrangler JK Jeep Radiator Wrangler JK Hemi Swap, radiator/fan Wrangler JK Jeep Radiator/Fan Wrangler JK, radiator/fan Wrangler JK Jeep Radiator/Fan Wrangler JK Hemi. These radiators are designed to be a direct replacement for the factory radiator on most Jeep Wranglers, 2007-2013. They are made with high-quality materials and construction to ensure durability and performance. The radiators also feature a number of design enhancements that improve cooling efficiency and airflow.

advertisement

Assistant Bot

Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.

Jeep Radiator Wrangler JK, radiator Wrangler JK Jeep Radiator Wrangler JK Hemi Swap, radiator/fan Wrangler JK Jeep Radiator/Fan Wrangler JK, radiator/fan Wrangler JK Jeep Radiator/Fan Wrangler JK Hemi Instructions | Manualzz

#52308 Jeep Radiator Wrangler JK

#52309 Jeep Radiator Wrangler JK Hemi Swap

#52388 Jeep Radiator/Fan Wrangler JK

#52389 Jeep Radiator/Fan Wrangler JK Hemi

READ BEFORE STARTING

Fits MOST Jeep Wranglers, 2007-2013 (Note: Automatic transmissions may require an auxiliary transmission oil cooler. Vehicle models may vary; Radiator only kits require Kit #32308 to attach factory fan.

For Hemi Motorswap Applications: A minimum clearance of 7-7/8” from the vehicle core support to the engine is needed to fit the radiator/fan combo. Some modification may be needed.

1 Scan here with your smartphone to see a step-by-step install video or type http://youtu.be/kMWHsM_WRFs into your favorite browser

Remove Stock Fan and Shroud Assembly

1. Make sure engine is cool.

2. Disconnect negative (-) battery cable from battery.

3. Remove 6ea. pop-clips on top of grille, twist turn signal bulbs and remove, and pop bottom clips from core support to remove grille.

4. Remove 2ea. phillips screws from bumper cover plate and remove panel.

5. Remove tree clips holding top and bottom radiator cover. (4ea. on top, 3ea. on bottom, 2ea. on bottom sides of radiator)

6. Loosen clamp at throttle body and remove sensor from intake hose. Remove air box, top radiator hose, and overflow bottle.

7. Turn drain plug at front passenger side in grille and drain. Remove bottom hose and push hose down to finish drain.

8. Remove five bolts holding A/C condenser to radiator. (4ea. on front of radiator, 1ea. on drivers side)

9. Unplug fan harness, detach tree harness on passenger side, remove bolts at top of radiator, and remove radiator.

2

Assemble Flex-a-Fit® Radiator

1. Attach both brackets #30893 flush with top of radiator tanks with 2ea. T-bolts, washers, and locking nuts.

2. Loosely attach bracket #30894 ~5-3/4” up from bottom of radiator on PASSENGER SIDE ONLY with 2ea. T-bolts, washers, and locking nuts.

IF INSTALLING RADIATOR ONLY KIT: Refer to

Instructions included in factory fan bracket kit #32308.

3

Transfer Radiator Mounts

1. Remove the factory rubber mounts on the bottom radiator posts as well as the top slotted holes.

2. Place factory rubber mounts into supplied upper radiator brackets and onto posts of supplied lower bracket.

4

Install New Flex-a-Fit® Radiator

1. Gently lower the radiator or radiator/fan combo into the engine compartment and place the lower post on passenger side bracket #30894 into the factory mount, making sure the top brackets line up with the factory core support mounting holes.

2. Mount top brackets to vehicle using stock hardware.

3. Verify hood clearance of radiator. If there are any interferences, loosen brackets and adjust where necessary.

4. Slide T-bolts into corresponding track on the driver’s side end tank to line up with the remaining bracket

#30894. Tighten bottom bracket mounting hardware on both sides. The radiator should be secured at this point.

5. Attach AC condenser to end tanks using the supplied brackets and t-bolts. (Only the 4 mounts on the front of the core will be attached to the radiator)

6. Install and securely clamp the bottom “outlet” radiator hose.

7. Install and securely clamp the top “inlet” radiator hose.

8. Mount overflow bottle into fan shroud and attach hose.

9. Reattach negative (-) battery cable from battery.

10. Reassemble vehicle panels, LEAVING STOCK RADIATOR

COVER PANELS OFF.

11. Refill radiator with coolant, and optionally Flex-a-Chill to protect your new radiator from corrosion.

Rev. 98388 05-16-16 1 of 2

5

Fan Wiring Instructions

FOLLOW THESE INSTRUCTIONS CAREFULLY TO AVOID

DAMAGING THE CONTROL UNIT, FAN MOTORS AND

YOUR VEHICLE! WHEN CRIMPING WIRES, ALWAYS USE A

QUALITY CRIMPING TOOL (DO NOT USE PLIERS OR

OTHER DEVICES).

6

VSC Mounting

1. Locate a mounting point for the VSC near inlet of the radiator. The control unit needs to be placed within

2-feet of radiator inlet hose for temp. probe placement.

On the fender well next to the radiator may be a convenient location.

2. Attach the control unit using the screws provided.

7

Controller Wiring

1. Using the large yellow butt connectors provided, attach a length of the thick (10 AWG) red wire to the orang motor wires at the fan.

2. Attach a length of the thick (10 AWG) black wire to the black motor wires at the fan.

3. Connect the thick red wire to the yellow VSC wire.

Connect the thick black wire to the purple VSC wire.

4. Determine the length needed to run thick red and black wire from the VSC to the battery terminals and trim appropriately.

5. Crimp a large yellow ring connector to one end of each wire and connect the black wire to the negative

(-) battery terminal, but DO NOT connect the red wire yet!

6. Using butt connectors, connect the fuse holder provided in line with the red wire.

7. Locate the fuse box.

8. Find a circuit that is hot when the key is in the ON position.

NOTE: DO NOT use the DRL or brake/taillight fuse!

9. Attach the included fuse tap to the fuse. Attach a female connector to the thin red wire included and connect to the fuse tap.

10. Attach pink female connector to end of the wire and connect to terminal #9 on VSC.

11. Locate the wires going to the A/C clutch. Determine whether the clutch is activated by a negative (ground) or positive signal. Connect the signal wire to the supplied thin green wire by use of a blue piggyback connector. Rout wire to VSC and trim to length. Attach a pink female connector and connect this wire to terminal #8 if the trigger wire is positive or to terminal #7 if the trigger wire is negative.

orange

8

Reassemble and Test

1. Insert temp. probe near inlet hose, leaving 1/4” of the probe sticking out from the core.

Be careful not to damage radiator core.

2. Turn Ignition on. If the LED farthest from VSC power wires does not turn on after 6 seconds, check 12V power going to terminal #9.

3. With engine running, turn A/C on. The fan should be running and 3 of the LEDs should be lit. If not, verify A/C clutch is engaged and correct signal wire is triggered.

4. Turn A/C off. Let vehicle warm up to normal operating temperature. Adjust screw terminal clockwise to increase turn-on temperature and counter-clockwise to decrease temperature. NOTE: THE SCREW TERMINAL

ONLY ROTATES 3/4 OF A TURN. IF TURNED BEYOND

ITS LIMITS THE TERMINAL WILL BREAK!

5. Once desired temperature is set, let the engine idle and make sure the fan cycles to maintain desired temperature. Make sure the fan is pulling air through the radiator toward the engine.

6. Reassemble vehicle & top off coolant.

9

What’s Next?

Register your product for warranty at http://automotive.flex-a-lite.com/warranty-registration/

Enjoy your Flex-a-lite performance cooling product!

If you need further assistance, please contact tech services at 253-922-2700 M-F 8:00am-5:00pm PST.

The Flex-a-lite Limited Warranty

Flex-a-lite Consolidated, 7009-45th St. Ct. E. Fife, WA 98424, Telephone

No. 253-922-2700, warrants to the original purchasing user, that all

Flex-a-lite products to be free of defects in material and workmanship for a period of 365 days (1 year) from date of purchase. Flex-a-lite products failing within 365 days (1 year) from date of purchase may be returned to the factory through the point of purchase, transportation charges prepaid. If, on inspection, cause of failure is determined to be defective material or workmanship and not by misuse, accidental or improper installation, Flex-a-lite will replace the fan free of charge, transportation prepaid. Flex-a-lite will not be liable for incidental, progressive or consequential damages. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may have other rights, which vary from state to state. The Flex-a-lite warranty is in compliance with the

Magnuson-Moss Warranty Act of 1975.

Rev. 98388 05-16-16 2 of 2

advertisement

Key Features

  • Direct replacement for factory radiator
  • High-quality materials and construction
  • Improved cooling efficiency
  • Increased airflow
  • Easy installation
  • Hemi Swap ready
  • Flex-a-Chill Corrosion Protection

Frequently Answers and Questions

What vehicles are these radiators compatible with?
These radiators are compatible with most Jeep Wranglers, 2007-2013. However, automatic transmissions may require an auxiliary transmission oil cooler. Vehicle models may vary, and some modifications may be needed for Hemi motorswap applications.
What is the minimum clearance required for Hemi motorswap applications?
For Hemi motorswap applications, a minimum clearance of 7-7/8" from the vehicle core support to the engine is needed to fit the radiator/fan combo. Some modification may be needed.
What is the warranty on these radiators?
Flex-a-lite warrants all Flex-a-lite products to be free of defects in material and workmanship for a period of 365 days (1 year) from the date of purchase. Products failing within 365 days from the date of purchase may be returned to the factory through the point of purchase, transportation charges prepaid. If, on inspection, the cause of failure is determined to be defective material or workmanship and not by misuse, accidental or improper installation, Flex-a-lite will replace the fan free of charge, transportation prepaid. Flex-a-lite will not be liable for incidental, progressive or consequential damages.
How do I contact Flex-a-lite technical support?
You can contact Flex-a-lite technical support at 253-922-2700, M-F 8:00am-5:00pm PST.

Related manuals

Download PDF

advertisement