Ematic DZP907 User manual
Add to my manuals43 Pages
DP VIDEO DZP907 is a versatile multimedia player designed to enhance your in-car entertainment experience. It supports a wide range of media formats, including DVD, VCD, CD, MP3, and MPEG-4, ensuring compatibility with various content. Additionally, it features a built-in TV tuner, allowing you to access your favorite TV channels. With Bluetooth connectivity, you can effortlessly connect your smartphone to the player to make hands-free calls, stream music, or access your phonebook.
advertisement
DZP907
DZP907
AUTO MULTIMEDIA AUDIO/VIDEO PLAYER
Contents
Thanks for choosing our products. Please read this User Manual carefully for functions and operations of this product and follow the precautions in it. Keep it properly for future reference.
1. Safety Precautions
2. Introduction to Panel Functions
3. Touch Screen Operation
4. Remote Controller
5. Basic Operations
6. Radio Operations
7. Bluetooth Operations
8. TV Operations
9. DVD/VCD/CD Operations
10. System Setup
11. MP3 Operations
12. Installation Guide
Control precations.
Retain this manual
13. Troubleshooting
14. Technical specifications
15. Accessories
23-27
27-34
34-36
36-37
38-39
40-41
41
* Important Tip: Calibrate the touch sreen before first use of this product (refer to Page 5).
* Note: As the technologies upgrade from time to time, the specifications shall be subject to
change without prior notice. screen
1-2
3-4
5-11
12-15
16-17
17-19
19-22
22-23
1. Safety Precautions
be sure wiring is installed the vehicles electrical system.
Improtant Safety Measures malfunction of
1) Make wiring according to the installation guide. Improper wiring may lead to maifuntction to
this product or damage to auto electric appliance.
2) Lead for speaker 1 shall be connected to termianl of the speaker 1. Never connect the lead
to the car body or an incorrect speaker terminal. the terminal of
3) Make sure the wiring is correct before powering on the product.
4) When replacing a fuse, only use a new fuse with the same specification. specifications
5) Do not block the ventilation hole or heat sink, or overheating inside this product may lead to
unstable performance. to begin using the product after installation or replacement of the vehicles battery,
6) After installation, begin to use the product (including replacement of automobile batteries).
First remove front panel, press "Reset" on the base with a pointed tool (it is forbidden to use
a sharp pointed object) to make the system in initial setup status.
Replace a Fuse enter in to
When replacing a fuse, make sure the original and new fuse have the same amperage. If the fuse is burnt, check power supply connection first before replacing it. If the new fuse is burnt out shortly, there may be internal fault and in this case, you shall contact the dealer. burns
Warning: be an should
Never use a fuse with a larger amperage than the fuse installed in this product, or it may lead to damage to this product.
Precautions supports
This product support the following discs:
1
Disc Type
DVD
Disc Mark Disc Content
Audio and Image
Disc Size
12cm
VCD
DIGITAL VIDEO
Audio and Image 12cm
VIDEO CD
CD Only Audio 12cm
DIGITAL AUDIO
MP3
DIGITAL AUDIO
Mp3
Only Audio
MPEG-4
DIGITAL AUDIO
Audio and Image
Note: VCD of this product is compatible with VCD 1.0/1.1/2.0/3.0 DVD disc.
12cm
12cm
* Do not alter this product as it may lead to accident. should
* Any operations to this product which may affect normal driving shall be conducted only after
the auto has been stopped.
* Do not keep this product running under excessively high or low temperature. Make sure the
internal temperature is within +60 and -10 before turning on the power.
* When playing CD, pay attention to the following precautions for optimal vedio and audio
effect: a CD,
- Hold the disc on the edge to keep it clean. video
- Do not use adhesive or ink on the disc.
- Do not use a disc with a sticker on it, as when the sticker falls off it may damage this product.
- Only use the special-purpose soft cloth wiping from the center to the edge to clean a disc.
2
2. Introduction to Panel Functions
1. Monitor.
2. MENU: In DVD mode, press the key
to return to the root directory of disc
menu; in radio mode, press the key to
switch to function operation interface.
3. :Stop playback.
a preset
4. EQ: Press the key to select preset
sound mode.
5. LOUD: Long press to enter/exit LOUD
function.
Please
DZP907
6. MIC: Pleas keep close the MIC input
in case avoiding communication under
Bluetooth mode.
7. RPT: Repeat Play.
knob
8. VOL/SEL: Turn the key to regulate the volume.
Press SEL, the following items will appear: L-front
/R-front/L-rear/R-rear/Subwoof/Bass/Middle/Treble/Volume.
9. / : under radio mode, press it to search channels automatically, and long press
it to search channels manually; under TV mode, press it to select the previous/next TV
channel; under playback mode, press it to select the previous/next music track, and long
press it to go fast forward and backward.
3
is a
10. SRC: Press the key to change modes.
11. BAND: under radio mode, press it to switch the radio bands;
12. AMS : In radio mode, press to scan the preset radio programs; long press to
auto-search and store radio programs.
13. : Play/Pause button.
14. PWR/ : Under power off mode, short press to turn on; power on mode, long press to turn
off. On work condition, short press for mute function.
15. AV IN: Under AV1 mode, audio and vedio input jack.
video
16. (USB Jack): Support 1.0/2.0 USB interface.
by the control
17. IR (Remote window): It can receive infrared signal transmitted by remote controller
supplied with the product.
receives the the disc
18. : Short press to enter/exit disc control function, long press to force exit.
19. OPEN: The TFT LCD is floating structure. Under power off condition, press this button to
turn on and flip up TFT screen, repress it to flip down TFT screen.
conditions,
20. SD/MMC Card Insert Jack.
21. Reset button. down the
4
3. Touch Screen Operations
from a
You can control the device by touching the screen.
Radio to the
Displays a
1. : Tap this area to go back to SOURCE.
2. Radio channel preset keys: Display list of
preset channels. Tap any preset key to receive
the program from pre-saved radio channel.
Long tap to save the current radio channel.
3. : Tap it to switch wave bands.
4. : Tap it to select between long-range and
short-range radio channels.
5. : Tap it to browse preset channels. Long
tap it to search for and automatically save radio channels.
6. : Tap them to search for radio channels downwards/ upwards automatically; Long tap to
search for radio channels downwards/upwards manually.
7. : Tap SYS to switch to system setup mode; when there is RDS function in the unit, this button
will change to , Tap PAGE1 to RDS set up interface.
8. LOUD: Tap it to turn on/off LOUD function.
9. EQ: Tap it to select form preset sound modes.
Multimedia from
In DVD mode, tap any point on the screen to display the following keys:
1. : Tap it to play/pause the playing.
2. : Tap it to stop playing, tap twice to stop
playing completely.
3. : Tap it to select the previous/next music track.
5
display the the lower right the left side of the screen twice corner twice
Note: In DVD mode, tap twice the left side on the screen to display TITLE MENU; tap twice the lower right corner to display ROOT MENU. In other playing modes, tap the upper right corner to display numeric keys and then tap any key to operate.
4. : Tap it to display DVD SETUP.
5. : Tap it to display SOURCE.
TV tap the
1. Preset TV channels: Display list of preset TV
channels. Tap any channel to receive corresponding
program. Long tap current channel to save it.
2. : Tap it to turn to the previous/next page.
3. : Tap it to automatically search for and save
TV channels.
4. : Tap them to search for TV channels
downwards/upwards automatically. Long tap them
1
6
5
to search for TV channels downwards/upwards manually.
5. : Tap it to display system setup interface.
2
6. PAL-DK: Tap it to switch between TV systems.
Bluetooth
Hands-free Telephone
1. : Bluetooth main menu
1 2. : Telephone directory
3. : Bluetooth setup page
4. : SOURCE.
5. Number area
6. : Dial key
7. : Clear key
8. : Hang-up key
9. : Switch mode of voice output
2
3
4
3
5
4
6
7
8
9
6
Telephone directory
1. : Display list of answered phone calls.
2. : Display list of dialed phone calls.
3. : Display list of missed phone calls.
4. : Turn to the next page.
Bluetooth setup
1. : Link to Bluetooth devices.
2. : Pair up with Bluetooth devices.
3. : Disconnect from Bluetooth devices.
4. : Restart.
5. : Play/pause.
6. : Stop playing.
7. : Back to the previous or go to the next.
8. : Adjust volume.
In A2DP mode, press keys 5-7 to make touch screen operation.
Setup
Switch to setup function. The screen will automatically go back to the current mode interface if no operations are conducted in 5s.
7
INFO
1. : Display options in front-seat mode.
Tap it to select the front-seat mode.
INFO
3. : Tap it to display the following:
Volume, L-front, R-front, L-rear, R-rear, Subwoofer,
Bass, Middle, Treble
Tap to turn to the next page and adjust the desired items; Tap to adjust the above items.
INFO
8
4. : Tap it to display the following:
Bright, Hue, Contract, Sharp is adjustable.
Tap the desired item and tap to adjust it.
5. : Display system settings.
For details, refer to System Setup in the next chapter.
6. : Back to the current SOURCE.
Tapping
System setup
Tap to page up/down.
Clock Sys: Set up time format (12H/24H).
Key Beep: Enable/disable key beep.
ON: Enable.
OFF: Disable.
Tap any key on the unit, remote control, or touch screen will not give out any beep.
Local Area: Switch radio frequencies based on your
location.
Tap to adjust bass freq, middle freq, and treble freq.
9
INFO
INFO
INFO
Tap to adjust subwoof freq, bass factor middle factor.
Back Bright (dimmer): Adjust backlight brightness in night mode. (25%, 50%, 75% or 100% of normal brightness)
Back light duration of the
Set the lasting time periods of backlight.
(Normal status: off, 15s, 30s, and 60s.) adjust the
Clock Adjust: Tap to adjust time:
Tap to select setup options (hour, minute, second);
Tap to adjust time in each option.
Touch Adjust: Calibration of the screen is needed when displayed position do not match touch position.
Tap the center of X on the touch screen and hold it for more than 1 second until adjust succeed appears on the screen.
10
INFO
INFO
INFO
GPS Mix SW: (This optional function may vary with actual
products.)
ON: Continue the original audio output when switching to
navigation;
OFF: Stop the original audio output when switching to nav
igation.
GPS Volume
Set the volume of GPS guiding voice. (HIGH/ Mid/Low)
(Optional, currently invalid.)
INFO
11
4. Remote Controller
Remote Controller Use and Maintenance
Installing battery
Slip out the battery tray in the back side, and insert the battery with its anode + and cathode - in proper position.
*Pull out the protruding film at first use.
in the
Warnings: Keep batteries out of the reach of children. Seek medical attention if batteries are swallowed by children.
NOTES:
Apply only a CR2025 (3V) lithium-ion battery into the controller; remove the battery if the controller is not to be used for a month or longer; do not charge, disassemble, or heat the battery, or throw it into fire; do not handle the battery with metallic articles; do not place the battery together with other metallic objects; clean the controller and install a new battery if the old one leaks liquids; dispose of the battery according to state/local laws and regulations; be sure that the anode
(+) and cathode (-) is properly positioned.
12
control
Instructions for Using Remote Controller
1. EQ : Press this key to select preset sound mode;
2. PWR/ : LongPress this key to start up; under playing mode,
Long press this key to turn off;Press the key to be mute.
3. AMS/RDM: In radio mode, press the key to scan the preset
radio stations, long press to search and store radio stations
automatically; in playback mode, press the key for random
playback.
4. RPT: In playback mode, press the key to repeat playback.
5. MENU: In DVD mode, press the key to return to the root
directory of disc menu. of the
6. [ ] [ ] [ / / / ] [ENTER]: In playback mode,
fast forward/backward, select up/down; in radio mode, search
the frequency and select up/down channels; in DVD setup menu, select file list and set directory
with arrow keys, and then press ENTER.
7. A-B/PROG: In playback mode, press the key to set the program order; in DVD/VCD mode, long
press to set the part for repeat playback.
settings
8. 0-9(Number keys): In radio mode, press number keys (1-6) to select the preset radio stations,
long press to store radio stations; in playback mode, press the key to select the setlist directly.
9. DISP/*: Under other modes, press this key to display time, output mode and setting menu (Disc/
SD/USB); under sound mode, repeatedly press this key to display play information; under
Bluetooth mode, press this key to dial.
10.
Press the disc
11. VOL-/SEL/VOL+: press "+" to increase the volume, press "-" to decrease the volume; Press SEL,
the following items will appear: VOL/BAL/FAD/BAS/TRE, then press "+/-" to adjust.
12. LOUD : Long press this key to turn on/turn off "LOUD" function;
13. SRC: Press the key to switch modes.
13
14. SUB-T/LOC: In FM mode, press the key to select long-range and short-range radio; in DVD
mode, press the key to change subtitle languages.
15. BAND/P/N: In radio mode, press the key to change wave band; in DVD/VCD mode, press the
key to select output format.
16. : Press the key to pause, press it again to continue.
17. TITLE: In DVD mode, press the key to return to title menu; in VCD mode, press the key to open
/close PBC functions.
18. : Press the key to stop playing. settings; display the
19. SETUP: Under playing mode, short press this key to display DVD setting; under DVD mode,
long press this key to display menu setting interface, short press this key under other modes to
display menu setting interface. the menu settings
20. : Playing DVD/VCD, press this key to watch slow motions. in slow motion.
21. ZOOM: When playing DVD/VCD, press this key to magnify or reduce the picture. view
22. ANGLE: When playing disks with function of angle switching, press this key to switch the angle angle of watching. a multiple angle function,
23. AUDIO/ST: In DVD mode, press the key repeatedly to select audio language; in VCD mode,
press the key repeatedly to select channel mode; in radio mode, press the key to select stereo
channel or mono audio channel.
24. CLEAR: Clearing function.
and the
25. GOTO/#: In DVD mode, press GOTO and cursor key to select title, setlist, disc sound, disc
subtitle, angle, title time, section time, repeat play, time display, then press ENTER to set; in
VCD mode, press GOTO and cursor key to select setlist, all disc time, track time, repeat play,
time display, then press ENTER to set; in CD/MP3 mode, press GOTO key to select track time
"_ _:_ _" or track "_ _:x x", then press 0-9 to select required track or time; in Bluetooth, press
the key to implement # dialing function; in radio mode, press the key and number keys to select
frequency.
select a
14
Bluetooth(Optional)
:under Bluetooth mode, press this key to dial or answer calls; under Bluetooth mode, this key
works as a key to input telephone numbers.
:under any mode, press this key to turn on Bluetooth; under Bluetooth mode, press this key to hang up or turn off Bluetooth.
RDS(Optional)
AF : Press the key to start up the AF (RDS function), long press to turn off RDS
PTY : press the key to select the RDS program, such as POP. M--NEWS --- INFO - FINANCE, there are totally 27 programs for choosing. Press enter after selecting category, the unit will search radio programs in this category automatically. You can also press the number keys 1-6 on the panel to save the radio programs in the corresponding key, the LCD monitor will show the abbreviation name of the radio programs
TA:Press this key to start TA function (Traffic Alert function), when it is turned on, the machine will switch into alerts automatically if there is a traffic alert,
GPS(Optional)
NAV:Press the key to enter into the GPS.
5. Basic Operations
Readjustment the battery.
This device shall be reset before first use or after replacing battery. Press ESET on the
panel to set the device in initial settings.
NOTE: This function is available only by pressing the button on this machine.
Power on/off
Press to power on.
NOTES:
Volume meter set between 6 and 30 will remain on the next power-on. When volume
meter is above 30, it will be restored to 30 after power off; when volume meter is below 6,
it will be restored to 6 after power off. This function is also available by pressing VOL/SEL
on this device.
Volume adjustment
Turn the VOL knob to adjust volume. Turn clockwise to increase; turn counterclockwise to
decrease.
Sound effect setup
Press SEL repeatedly to select desired mode as follow:
L-front R-front L-rear R-rear Subwoof
Volume Angle Treble Middle Bass
NOTE:
Turn VOL knob to adjust the status of current mode after selection.
16
Press
Mute function the audio
Pressing to shut off audio output, with MUTE displayed on the screen. Press it again
to unmute.
the remote control.
Notes: This function is available by the buttons on this device and remote controller.
EQ Setting
Press EQ to switch preset modes as follow:
POP CLASSIC
EQ OFF ROCK
6. Radio Operations
Switch to radio mode to display as follow:
1. Waveband selection follows:
In radio mode, press BAND repeatedly to switch
between wavebands as follow:
FM1 FM2 FM3 follows:
MW2 MW1 on the
This function is available through BAND on touch
screen or panel.
17
SYS
in the
2. Manual/Automatic tuning
(1) Manual tuning: Long press / on remote controller repeatedly to tune to the desired
frequency.
(2) Automatic tuning: Press / to search for radio channels automatically.
This function is available by (long) pressing on front panel.
3. Preset radio channel reception
This device can save 30 radio channels. (18-FM, 12-FM)
Press to select from saved radio channels with current wave band, number and
frequency displayed on the screen.
on the
This function is also available by pressing the Radio Channel Preset button on touch screen.
This function is also available by pressing the Radio Channel Preset buttons (1-6) on
remote control.
on the
4. Saving preset radio channels automatically/manually
Six radio channels can be saved for every waveband.
Save channels automatically
(1) Waveband selection
(2) Press AMS, the tuner will automatically search for and save radio channels with stronger
signals in selected waveband.
Save channels manually
(1) Select waveband and tune to radio channels to be saved.
the remote control
(2). Long press any of the radio channel preset keys (1-6) on remote controller or touch
screen to save the selected radio channel.
If you save a new radio channel, the current channel, if any, will replaced by the new channel.
18
5. Long-range, Short-range selection
In radio mode, press LOC to receive radio channels with strong/poor signal.
with a
(1) When the monitor displays LOC: ON after pressing LOC, only radio channels with
strong signal can be received.
(2) Press LOC again, the monitor displays LOC: OFF and radio channels of both strong
and poor signal can be received.
6. Mono/Stereo selection
In FM mode, press ST to select mono or stereo radio loud
7. Bluetooth Operations
Hand-Free Telephone (HFT) hands to the
This device can make hand free calling by connecting this device to a mobile phone supporting
Bluetooth (Please refer to user manual of your mobile phone for Bluetooth settings) ;
Please speak aloud and clearly during telephone conversation.
Please close car windows before dialing.
Noise may appear in the call due to human factors and weak signals.
Restriction of mobile phone may prohibit the use of HFT function. of the
Connection
Switch to Bluetooth mode
Tap PAIR to enable pairing function
19
of the
Enable the searching function of mobile phone (BtCarKit)
Select Bluetooth device in the mobile phone (BtCarKit)
Type in pairing code 1234
Successful connection (The monitor will display Connect )
NOTES: to the
Connect this device with mobile phone by Bluetooth wireless transmission; (Please refer to
user manual of your mobile phone for Bluetooth settings)
After successful pairing within valid range, if the connection is interrupted accidently, TFT
will display NO Connect press LINK on monitor to reconnect. (Please refer to Bluetooth
Setup on page 6) on the the dialed
Making calls with the on the
1. Enter telephone numbers with number keys on remote control
controller or touch screen, then press to make a
call with the screen displaying dialed phone number.
2. Making a call in Call History: switch to interface of
Phone Book. You can make a call by selecting a
number from the list of received calls, dialed calls or
missed calls and then pressing the key .
A maximum of 16 records can be saved in each list.
Turn pages by tapping on touch panel.
on the
20
Answering calls
For an incoming call, the ringtone sounds with the caller's number displayed on the screen; tap on the touch screen to answer it.
Ending calls on the
Press on touch screen to hang up.
Pressing / on the remote controller can also
make/end a call.
The system will automatically stop other audio resource and switch to HFT interface when
there is an incoming call; the system will automatically return to previous mode after ending to the on the the call.
Voice is output through loudspeaker by default. Tap Audio Transfer on touch screen to
switch to phone mode during conversation; tap it again to return to hand-free mode. (Please
refer to page 5 for details.)
Bluetooth audio functions
This device supports wireless control/operation of the audio files on devices supporting Bluetooth, such as mobile phone and portable player.
For details about connecting Bluetooth device, please refer to Connection in Bluetooth Operations.
For information about operation, please refer to Bluetooth
Setup on page 6.
21
Do not support video playing.
This function is also available by remote control.
Remote controller prompts;
Pause/Play control
Select the previous/next music
Stop playing
8. TV Operations
Analog Television
1. Mode selection control
Select TV mode by pressing SRC on the remote controller or panel or tapping the touch panel.
2. TV Channels Search (Auto Search):
Press / on the remote controller or tap SEEK-/SEEK+ on touch screen to search for TV channels automatically.
3. Save TV channels automatically:
Press AMS on the remote controller or touch screen to save the searched TV channels automatically to memory in sequence.
4. TV channels selection
1). Press / on the remote controller to select saved channels upwards and downwards.
2). Press the number keys (1-9) on the remote controller to select channels directly. Press
GOTO on remote controller and then press the corresponding numbers to select channels on the control
22
of multi digits.
on the
3). Tap the touch screen to select channels. Tap the button CH-/CH+ on monitor to turn pages.
5. TV system selection on the select the the menu
Repeatedly tap PAL-DK on touch screen to select corresponding TV system in user's location.
NOTES: When watching TV, tap monitor to display menu of TV operations. The menu will
automatically hide the menu in case of no operations in five seconds.
9. DVD/VCD/CD Operations
a disc
1. Disc insertion
Insert disc to automatically switch to DVD mode.
Press on this device to eject disc.
2. Quick selection of music fast forwards/backwards
Press to play the previous music, press to play the next music.
This function is also available by pressing / on this machine.
Press / on remote controller to play fast forwards/backwards with speeds switching as
follows: on the
3. Stop playing play the
Press to make this device in pre-stop status, then press ENTER to play current music or
chapter, press it twice to stop playing completely, and press ENTER to play from the first
music track.
23
4. Pause Playing
Press to pause playing, then press it again to resume playing.
5. Random playing
In VCD, CD mode, press RDM on the remote control, RANDOM will display on the
screen and this device will enter random playing. Press it again to exit this function.
6. Replay
In playing mode, press RPT on the remote controller to enable replay.
The DVD will repeat playing as follow: follows:
CHAPTER TITLE
OFF
The VCD/CD will repeat playing as follow: follows:
TRACK OFF
* The device replays the whole disc by default
7. Slow Motion Playing follows
The DVD will play as follow by pressing repeatedly: follows
The VCD will repeat playing as follow by pressing repeatedly:
This function is only available by remote control.
24
8. Zoom/Resize image
In DVD/VCD mode, press ZOOM to resize video as follow:
This function is only available by remote control.
9. System switching follows
In VCD mode, press AUDIO on the remote controller to switch systems as follow:
TRACK OFF
MONO LEFT MONO RIGHT stereo
STRTEO MIX-MONO
10. Programming playing press the
In DVD/VCD/CD mode, press PROG to display program editing menu, then press
number keys to enter the track ID which requires programming and move the cursor to
tart and press it to began programming playing; Move the cursor to EXIT and press
ENTER to exit this function; Move the cursor to PREV and press ENTER to go
to the previous page; Move the cursor to NEXT and press ENTER to go to the next
page.
In program playing, press PROG to exit.
This function is only available by remote control.
25
11. Subtitle language Selection (Multi-subtitles)
The user can switch subtitle languages when playing DVD with multi-subtitles. Press
SUB-T to switch subtitle languages as follow:
Subtitle 01 Subtitle 2 Subtitle OFF follows:
NOTES:
This function is only available by remote control.
This function is only available for DVD with subtitles.
12. Audio Language Selection (multiple audio tracks)
DVDs with
The DVD player supports voice in multiple languages and various audio systems. You can
shift among different languages and audio systems when playing a DVD disc with multiple
audio tracks. Press AUDIO repeatedly to switch dialogue languages as follow:
Audio 01 Audio 02.
NOTES:
This function is only available by remote control.
This function is only available for DVD with multiple audio.
13. Menu selection (DVD mode) for DVDs control follows:
While playing DVD, press TITLE on the remote controller to return to root menu, and then
press or to select different chapters or titles.
This function is also available by tapping the touch panel.
14. Root menu selection (DVD mode)
When playing DVD, press MENU on the remote controller to select root menu, press
and ENTER to enter submenu, and then enter your desired menu using arrow
keys, number keys and ENTER.
26
15. Menu Setup control
In DVD/VCD/CD mode, press SETUP on the remote controller to display menu settings.
The user can select demanding menu by pressing on the remote controller and
press ENTER to confirm.
menu options control
NOTES:
This function is also available with touch screen.
the default
If the selected language is not recorded on the disc, default language will be displayed.
Please refer to System Setup for details on SETUP MENU.
Function settings may vary with devices or disc formats.
16. Switching Video Automatically on the if a
Attention: The Video is Disabled While driving will appear on TFT monitor if DVD is
played while driving; the system will automatically switch to playing state after stopping the
auto.
17. Switching to rear view in backing
The system will switch to rear view when the car is backing.
10. System Setup
choose an display the
Press SETUP on the remote controller to display setup menu, which contains submenus of common settings, audio settings, parameter settings, password settings and exit settings.
1. Shift up/down/left/right arrow key on the controller to an item which needs adjustment and
select it by pressing ENTER. Press left arrow key to return to the previous menu.
2. To exit from the setup menu, select Exit or press SETUP.
* You can also perform setup operations by touching the screen.
27
If a to a
1. General setup page
1.1 Screen aspect ratio
Screen aspect ratio and pictures may vary according to different discs and screens.
NOTES: and the is in
If disc picture comes preset at 4:3, adjustment of screen display will not change the ratio. Refer to specific DVD format to select from diversified display formats. Video pictures can be will remain their original formats regardless of the changing of screen display format.
1.2 OSD language of of the
You can select a certain language according to your needs.
28
2. Audio setup page
You can set up digital audio and Dolby bits according to your needs.
2.1 Digital audio setup
SPDIF OFF
Select it to turn off digital audio output.
The device will output analog audio after being connected with audio output wire (including front, back, left, right, middle and mega bass).
SPDIF RAW
Simultaneous output of digital audio and analog audio.
SPDIF PCM
Output digital audio
29
2.2 Dolby Setup
DUAL MONO
Select it to enable dual audio output.
DYNAMIC
Select it to adjust audio dynamic ranges.
3. Initial setup page
This function can be activated only when playing is completely stopped. The settings will remain at the next power-on. when playing a 3.1 Audio language
Set up your preferred audio language in playing DVD.
(Only effective when the DVD disc supports the language.)
3.2 Subtitle
Set up your preferred DVD subtitle. (Only effective when the DVD disc supports the language.)
30
3.3 Disc menu
Set up your preferred disc menu. (Only effective when the DVD disc supports the language.)
3.4 Parent control on the
This function depends on classification of DVD discs.
Note:
* Parent control is ineffective if the password control
is disabled;
* To keep parent control effective, enable the password
control after setting.
3.5 Factory settings
Press ENTER to set the device into its factory settings.
to
31
4. Password setup page
4.1 Password control
Enable password control to lock up the password, and disable password control to unlock password.
* Enabling/disabling password control
requires previous password.
* Initial password is 136900.
4.2 Password change
You can change the password when required. Enter 6 digits as your new password.
You can tap the password input box to display number keys and then enter a new password.
32
5. Exit from system setup on the
Move the cursor to with arrow keys on remote controller, and press ENTER to exit from system setup.
Tap to exit directly.
6. TV picture size Setup
Different TV picture aspect ratios:
Picture Frame
4:3 Panorama
4:3
4:3
TV Picture Sizes
4:3 Mailbox
16:9
Wide Screen
16:9
33
7. Disc-supported functions
This device supports an array of disc functions:
2
Region code and signal system
8 Digital language
DIGITAL
SURROUND
Dolby surround
DTS surround 16 : 9 LB
Subdirectory language
Picture aspect ratio
R RESTRICTED
CC
Restricted
View angle
Disable subtitle
11. MP3 Operations
Insert an
1. Insert MP3-compatible disc, SD card and USB driver. to insert a
Remove the plastic cover in the lower left corner of the panel and inset USB driver or SD/MMC card. The unit automatically switches into MP3 mode, and the screen displays the following:
Tap this area to display number keys Click here to display number keys
Tap the up/down arrow keys to page up/down.
* Page up/down by pressing on the remote controller
when playing is stopped.
* Press on the unit to eject discs.
2. Replay
Press RPT on the remote controller for replay of the current music with REPEAT ONE displayed.
34
When
3. Music selection
MP3s,
- Upward/ downward music selection
In playing Mp3, press on the remote controller or tap NEXT/PREV on the touch screen to select music upward/downward.
- Digital music selection
Press number buttons on the remote controller to select. To select a multi-digit music ID, input the ID from the left to right digit using number buttons, e.g., to select 23rd piece of music, press
2 first, then press 3.
Note: performed through the remote control
* This function is performable through remote controller and numeric keyboard on the screen which appears after tapping the screen on the upper right corner. Press CLEAR to clear false inputs.
4. Stop
Press on the remote controller or tap STOP on the touch screen to stop playing.
5. Pause
Under playing state, press on the remote controller to pause, and press it again to resume playing. Press BAND/ on the panel or tap PAUSE on the touch screen to perform the same operation.
6. Fast forward/backward playing
Press to fast forward or press to fast backward. Speed factor follows the cycle below for each pressing:
Long press on the panel to perform the same operation.
35
7. Folder operation
If folders are contained in discs, SD cards, or MMC cards, press on the remote controller or tap PREV/NEXT on the touch screen to select the desired folder, then press ENTER on the remote controller to start music playing automatically from the first piece.
control
12. Installation Guide
Make sure this device works normally before installation.
Please use only the accessories supplied with the device to ensure
proper installation. Using unauthorized accessories may cause faults.
If any modifications to your car is required to install the device, such drilling
as punching, please consult the dealer.
Installation of this device shall not block the driver's view or pose
danger to passengers in case of sudden braking.
near a heating outlet,
Do not install this device in hot places, such as nearby heating air outlet, as overheating
may damage semiconductor laser components.
To get the best performance, the installing gradient shall not be over 30 . angle should
36
Device Installation metal
Mount the metal bush into the instrument panel, and bend the mental jaws by 90 to fasten it.
Fasten floor iron bar to the corresponding metal part on the chassis to improve anti-interference c apability. Slide the device into the metal bush until the spring plates on both sides fix the device securely.
Device Disassembly
Disassemble the decorative frame first, separately align the notch of disassembly keys
(accessories attached to the device.) to the hole on both sides of the device, and then insert.
When you hear a click indicating that fastening spring plates have been pressed down, pull out the device by grasping the keys.
the
37
13. Troubleshooting
Common problems
Problem
Can't turn on the device
The remote control is invalid
Can't play the disc
No sound
symbol appears and can't operate
The audio and video skip
The disc can't be rejected
The disc is in the slot but there is no sound, or the disc is rejected automatically
Reason
The wire isn't connected to the melted connector properly; The fuse is melt
Solution
Please make sure all connections are properly; Please replace new with the
Battery capacity is low
Disc is dirty;
The disc is incompatible
The connection isn't proper;
For certain discs, the 96KHZ sampling frequency is disabled
This operation is disabled for disc;
The operation isn't compatible with the disc
The device isn't installed properly
The disc has defect;
The device has fault
The disc isn't installed properly;
The disc is dirty or scratched
Clean the disc;
Check the disc type
Check the connection;
Set the output to 48KHZ sampling frequency
Can't operate
Can't operate
Fix the device; refer to the installation guide
Press and hold the EXIT( ) button; if the normal operation isn't restored, please contact local retailer or maintenance center
Keep the disc label upwards;
Clean the disc or replace a new disc
38
Problem
DVD
Can't switch the audio language and caption language
No caption
The SETUP MENU doesn't have the audio language and caption language
Can't switch watching angle
While playing, the image isn't clear/distorted and dark
Reason
VCD
Can't use PBC (playback control) menu
The played VCD disc doesn't have
PBC function;
PBC is switched to OFF
Can't repeat playing and search PBC is switched to ON
Solution
The disc isn't recorded with several languages; you can only switch among the options indicated in the disc items
The disc doesn't have caption
The playing disc doesn't have the audio language or caption language selected in the SETUP MENU
The disc doesn't have multiple angles; try to switch the scene that isn't recorded with multiple angles to multi-angle mode
The disc is recorded with the signal of copy protection (certain discs may integrate)
If the disc isn't recorded with several languages, you can't switch the language
The disc doesn't have this function
If the selected language isn't recorded, you can't switch to this language
If the disc isn't recorded with multiple angles, you can't switch the playing angle; switch the angle if the scene has multiple angles
Since this device is compatible to the copy protection system, when you play the disc with copy protection signal, the image on certain monitors may have horizontal veins or other defects; however, it doesn't indicate that the device has problem a problem
For the VCD that doesn't have PBC function, it is not possible to switch
PBC to ON
Switch PBC to OFF
39
14. Technical Specifications
General specifications
Power: DC/12V (10.8~16V)
Grounding: Negative grounding
Maximum current: 15A
Maximum power: 4 40W
Load resistance: 4 (4~8 )
Dimensions: 178mm(W) 50mm(H) 230mm(D)
Weight: 2.6KG
DVD Player
Audio output: 2.0Vrms 0.3V 10K
S/N Ratio: 62dB(1KHz)
Dynamic range: 80dB(1KHz)
Distortion: 0.2%
Video output: 1.0Vp-p 0.2V/75
40
FM Tuning
Practical sensitivity: 10dB
S/N Ratio: 55dB (mono)
Distortion: 0.5%(mono)
Stereo Crosstalk: 30dB(1KHz)
MW Tuning
Practical sensitivity: 30dB
S/N Ratio: 50dB
15. Accessories
1. Bushing (one)
2. Decoration frame (one)
3. Remote controller (one)
4. Disassembling keys (two)
41
5. AV input conversion line (one)
6. Power line (one)
7. User's Manual (one)
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project