Harley-Davidson Solo Detachable Luggage Rack Instructions

-J04785
REV. 2008-06-20
DETACHABLE SOLO LUGGAGE RACK
GENERAL
is05542
Kit Number
5
2
54213-09
Models
For model fitment information, see the P&A Retail Catalog or
the Parts and Accessories section of www.harley-davidson.com
(English only).
1
erman
G
.
e
.
y
n
The rider's safety depends upon the correct installation
of this kit. If the procedure is not within your capabilities
or you do not have the correct tools, have a HarleyDavidson dealer perform the installation. Improper installation of this kit could result in death or serious injury.
(00308a)
Kit Contents
See Figure 3 and Table 1.
w
w
INSTALLATION
w.
Install a docking point kit using the kit instructions.
2.
See Figure 1. While standing behind the motorcycle, place
the rack side plate notches (4) into the upper shock
absorber mounts (3). Make sure the notches seat fully into
the mounts.
3.
4.
3
1.
2.
3.
4.
5.
6.
Docking plate
Solo rack
Upper shock mount
Side plate notch
Rotary latch
Docking point
h d o nli
1.
See Figure 2. Position the rotary latches (1) over the rear
docking points (2). Check to be sure the rotary latches fit
into the neck of the rear docking points as shown. This
may require some gentle squeezing or spreading of the
side plates.
4
o p. d e
Rosto
ck
Separate purchase and installation of additional parts or
accessories is required for proper installation of this kit on your
model motorcycle. Please see the P&A Retail Catalog or the
Parts and Accessories section of www.harley-davidson.com
(English only) for a list of required parts or accessories for your
model.
is05538
sh
Additional Parts Required
6
e
Figure 1. Detachable Solo Rack
n
1
2
Push the rear of the side plates downward and close the
rotary latches by pressing the latch lever as far forward
as it will go. You will hear a CLICK when the latch is in
place. If the latch does not easily close, do not force.
Recheck alignment.
1. Docking point latch in locked position
2. Docking point
Figure 2. Latch and Docking Point
-J04785
1 of 2
NOTE
You must hear a CLICK to verify that the rotary latch is completely in engaged.
SERVICE PARTS
is05539
The docking points must be fully engaged. See Figures 1 and
2 for correct engagement. If docking points are not fully
engaged it could shift position or come loose during operation.
1
Luggage Rack capacity is 10 lbs.
Do not exceed luggage rack weight capacity. Too much
weight can cause loss of control, which could result in
death or serious injury. (00373a)
5.
3
4
To remove the solo rack, press the release button on each
side and push the rotary latch levers back. Carefully lift
the rear of the side plates up and pull the side plate
notches out of the upper shock mounts.
2
Figure 3. Service Parts: Detachable Solo Luggage Rack
erman
G
.
e
.
y
n
Table 1. Service Parts
w
w
-J04785
Description (Quantity)
Part Number
Detachable solo rack, chrome
Not Sold Separately
2
Rotary latch assembly, left
53509-95
3
Rotary latch assembly, right
53508-95
4
Splined stud (2)
45728-95
5
Docking point bushing (2)
52682-09
6
Label, (not shown)
Not Sold Separately
7
Wave washer (not shown)
8
Flat washer, stainless steel (not 6827
shown)
9
Button head screw (not shown) 2957
o p. d e
1
6828
sh
Rosto
ck
Item
w.
h d o nli
n
e
2 of 2