Important Information

SCEPTRE E27 Page1

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following conditions:

This device may not cause harmful interference

This device must accept any interference received, including interference that my cause undesired operation.

Please Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and the receiver.

 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Caution: To comply with the limits for an FCC Class B computing device,

always use the signal cord and power cord supplied with this

unit.

The Federal communications Commission warns that changes or modifications to the unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Page2 SCEPTRE E27

European Notice

CE mark for Class B ITE (Following European standard EN55022/1998;

EN61000-3-2/1995; EN61000-3-3/1995, EN55024/1998,

EN60950/1992+A1+A2+A3+A4+A11)

Radio Frequency Interference Statement

Warning:

This is a Class B product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.

Canadian Doc Notice

For Class B Computing Devices

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference

Regulation of the Canadian Department of Communications.

“Le présent appareil numérique n’èmet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class B prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada."

SCEPTRE E27 Page3

Important Information

Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can result in electric shock and / or fire. In order to prevent potential danger, please observe the following instructions when installing, operating and cleaning the product. To ensure your safety and prolong the service life of your Liquid Crystal

Display, please read the following precautions carefully before using the product.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade and the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at the plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightening storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Page4 SCEPTRE E27

Tips and Safety Precautions

This product is designed and manufactured to operate within defined design limits, and misuse may result in electric shock or fire. To prevent the product from being damaged, the following rules should be observed for the installation, use and maintenance of the product. Read the following safety instructions before operating the display. Keep these instructions in a safe place for future reference.

 To avoid the risk of electric shock or component damage, switch off the power before connecting other components to the

E27 LED MONITOR.

 Unplug the power cord before cleaning the

E27 LED MONITOR. Do not use a liquid or not blocked or covered. Do not place the

E27 LED MONITOR in a bookcase or cabinet unless proper ventilation is provided.

 It is not recommended to use the E27 LED

MONITOR in a portrait format (by rotating a spray cleaner for cleaning the product.

Do not use abrasive cleaners.

 Always use the accessories recommended by the manufacturer to insure compatibility.

 When moving the E27 LED MONITOR from an area of low temperature to an area of high temperature, condensation may form on the housing. Do not turn on the

E27 LED MONITOR immediately after this

90 degrees) under high temperature environment (25°C or higher), since this would retard heat dissipation and would eventually damage the monitor.

 Never push any object into the ventilation slots of the E27 LED MONITOR. Do not place any objects on the top of the Product.

It could short circuit parts causing a fire or electric shock. Never spill liquids on the

E27 LED MONITOR.

 The E27 LED MONITOR should be operated only from the type of power to avoid causing fire, electric shock or component damage.

 Do not place the E27 LED MONITOR on an unstable cart, stand, or table. If the E27

LED MONITOR falls, it can injure a person and cause serious damage to the appliance. Use only a cart or stand recommended by the manufacturer or sold with the E27 LED MONITOR.

 Any heat source should maintain a distance of at least 5 feet away from the

E27 LED MONITOR, i.e. radiator, heater, source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company.

 The power cable must be replaced when using different voltage from that specified in the User Manual. For more information, contact your dealer.

 The E27 LED MONITOR is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit only into a grounded power outlet as a oven, amplifier etc. Do not install the product too close to anything that produces smoke or moisture. Operating the product close to smoke or moisture may cause fire or electric shock.

 Slots and openings in the back and bottom of the bezel are provided for ventilation. To ensure reliable operation of the E27 LED

MONITOR and to protect it from overheating, be sure these openings are safety feature. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely.

Do not defeat the safety purpose of the grounded plug.

SCEPTRE E27 Page5

 Do not overload power strips and extension cords. Overloading can result in fire or electric shock.

 The wall socket should be installed near the equipment and should be easily accessible.

 Only the marked power source can be used for the product. Any power source other than the specified one may cause fire or electric shock.

 Do not touch the power cord during thunderstorms. To avoid electric shock, avoid handling the power cord during electrical storms.

 Unplug the unit during a lightning storm or when it will not be used for a long period of time. This will protect the E27 LED

MONITOR from damage due to power surges.

 Do not attempt to repair or service the product yourself. Opening or removing the back cover may expose you to high voltages, the risk of electric shock, and other hazards. If repair is required, please contact your dealer and refer all servicing to qualified service personnel.

 Keep the product away from moisture. Do not expose this appliance to rain or moisture. If water penetrates into the product, unplug the power cord and contact your dealer. Continuous use in this case may result in fire or electric shock.

 Do not use the product if any abnormality occurs. If any smoke or odor becomes apparent, unplug the power cord and contact your dealer immediately. Do not try to repair the product yourself.

 Avoid using dropped or damaged appliances. If the product is dropped and the housing is damaged, the internal components may function abnormally.

Unplug the power cord immediately and contact your dealer for repair. Continued use of the product may cause fire or electric shock.

 Do not install the product in an area with heavy dust or high humidity. Operating the product in environments with heavy dust or high humidity may cause fire or electric shock.

 Hold the power connector when removing the power cable. Pulling the power cable itself may damage the wires inside the cable and cause fire or electric shocks.

When the product will not be used for an extended period of time, unplug the power connector.

 To avoid risk of electric shock, do not touch the connector with wet hands.

 If any of the following occurs please contact the dealer: o The power connector fails or frays. o Liquid sprays or any object drops into the E27 LED o

MONITOR.

The Display is exposed to rain or o other moisture.

The Display is dropped or o damaged in any way.

The performance of the Display changes substantially.

 Operating environment: Temperature: 5°C

~ 35°C, Humidity: 10% to 90% non-condensing, Altitude: 0~10,000 ft.

Page6 SCEPTRE E27

Table of Contents

Important Information.................................................................................................................................1

FCC Compliance Statement ......................................................................................................................2

Important Information.................................................................................................................................4

Tips and Safety Precautions ......................................................................................................................5

Table of Contents .......................................................................................................................................7

Opening the Package ................................................................................................................................9

Package Contents......................................................................................................................................9

Installing or Uninstalling the Base .............................................................................................................9

Setting Up Your Monitor ...........................................................................................................................10

Mounting Preparations.............................................................................................................................10

Identifying Front and Rear Panel.............................................................................................................12

Front View .....................................................................................................................................12

Connections ..................................................................................................................................13

Understanding Your Cables & Connections.................................................................................13

Connecting the LED Monitor ...................................................................................................................14

If You have DVI Connection on Your Video Card….....................................................................14

If You have VGA Connection on Your Video Card… ...................................................................15

If You have HDMI Connection on Your Cable or Satellite Box… ................................................16

On Screen Display (OSD) Menu .............................................................................................................17

PICTURE SETTINGS ...................................................................................................................18

COLOR ADJUST ..........................................................................................................................19

IMAGE ...........................................................................................................................................20

SIGNAL SOURCE ........................................................................................................................21

OSD MENU ...................................................................................................................................22

MISC. ............................................................................................................................................23

Supported PC Resolution ........................................................................................................................24

Supported Video Resolution ....................................................................................................................24

Troubleshooting .......................................................................................................................................25

How do I clean the LED Monitor?............................................................................................................28

Specification .............................................................................................................................................29

Call Us If You Need Help! ........................................................................................................................30

LIMITED PRODUCT WARRANTY ..........................................................................................................31

Disclaimer & Copyright Information.........................................................................................................33

SCEPTRE E27 Page7

Dear SCEPTRE Customer,

Congratulations on your new SCEPTRE E27 LED monitor purchase. Thank you for your support. To ensure safety and many years of trouble free operation of your LED monitor, please read the manual carefully before making any adjustments, and keep them in a safe place for future reference. We hope you enjoy your new SCEPTRE monitor.

For technical assistance, please call 1800-788-2878 and select option 3 or email our tech support group at [email protected]

.

For all other inquiries, please call 1800-788-2878 and select option 4 or email our customer service group at [email protected]

.

Live Chat also available during business hours M-F 8:30AM-5:30PM.

We recommend you register your SCEPTRE monitor by going to our website http://sceptre.com/service_registration.php

.

Page8 SCEPTRE E27

Opening the Package

The SCEPTRE E27 LED monitor is packaged in a carton together with standard accessories. The weight of the LED display is approximately 12.61 lbs. Since the LED panel can be easily scratched or broken, please handle the product gently. Never place the unit on a surface with the glass facing downwards unless it is on a protective padding.

When opening the carton, make sure the product is in good condition and that all the standard accessories and items are included. After unpacking your LED monitor, be sure to save the original box and all packing materials for future shipping needs.

Package Contents













Monitor Display x 1

Base x 1

User Manual x 1

Power Cord x 1

VGA Cable x 1

HDMI Cable x 1

Installing or Uninstalling the Base

1. Please place the base on a flat surface (i.e. table). Hold the monitor directly 90 degrees above the base.

Connect the monitor to the base by inserting the monitor into the base. To remove the base simply look at the bottom of the base and unlock the two buckles at the bottom of the base.

SCEPTRE E27 Page9

Setting Up Your Monitor

The following are general short steps to setup and use the monitor with your PC under the Windows 7 operating system.

1.

2.

After you have installed the base, connect your VGA or DVI cord to both the monitor and PC and turn on the PC and the monitor.

Under Windows, use your mouse to right click on the wallpaper and select the

RESOLUTION option.

3. Change your resolution to 1920 x 1080 and click on APPLY.

For Microsoft Windows 8

1.

2.

3.

4.

After you have installed the base, connect your VGA or DVI cord to both the monitor and PC and turn on the PC and the monitor.

Under Windows, use your mouse to select Desktop.

Once you’re on the desktop, right-click on the wallpaper and select the

RESOLUTION option.

Change your resolution to 1920 x 1080 and click on APPLY.

Page10 SCEPTRE E27

2. Mounting Preparations

1. Place the monitor on a flat surface with cloth so the bezel does not get scratched. Look at the base where the two buckles are located. Pull / expand them outwards while pulling on the base and it will come off.

2. The monitor is ready for mounting. Unfortunately you cannot remove the neck piece.

Please note : The mounting pattern of the monitor is 100mm x 100mm using M4 metric system screws.

The screw depth of the mounting pattern should not exceed 6mm. The 4 screws removed are for securing the monitor stand only. If you are mounting the monitor please consult a qualified installer for further instructions on bracket support and wall support.

SCEPTRE E27 Page11

Identifying Front and Rear Panel

Front View

POWER INDICATOR - If light is blue, the monitor is turned on. If the light is blinking blue, the monitor is turned on but not receiving a signal from the computer.

NATIVE RESOLUTION - This monitor’s clearest picture is produced under its native resolution. The native resolution of the monitor is 1920x1080 at 60 Hz refresh rate.

MENU – Menu button brings up the on screen menu. When the on screen menu is being displayed the menu button functions as ENTER.

DOWN – The down button navigates the selection on the on screen menu downwards. When an option is being adjusted, the down button decreases the adjustment. This button is also the hotkey for volume down.

UP – The up button navigates the selection on the on screen menu upwards. When an option is being adjusted, the up button increases the adjustment. This button is also the hotkey for volume up.

EXIT – The exit button exits either the on screen menu or your current selected option.

SCALE – The scale button switches between 16:9 or 4:3 screen mode.

SOURCE – The source button selects between the 3 sources on the monitor (HDMI, DVI and VGA).

- The power button turns the monitor on or off.

Page12 SCEPTRE E27

Connections

HDMI – HDMI stands for High Definition Multimedia Interface. This connection is for A/V devices such as Blu-ray player, DVD player or game consoles such as Playstation®3.

DVI – DVI stands for Digital Video Interface. This connection is for computers to send video signals to the monitor digitally so that colors and video are more accurate and vivid.

VGA – VGA stands for Video Graphics Array. This connection is for computers to send video signals to the monitor by an analog signal. This method of connection is the most commonly used connection.

AUDIO IN – This connection is for audio out from the PC to connect to the monitor.

POWER – This plug is responsible for providing power to the monitor.

Understanding Your Cables & Connections

Cable

Name

DVI

(digital video)

Cable Picture

Corresponding Connection

Picture

VGA

(analog video)

3.5 mm

Mini-jack

HDMI

*The cables above do not represent the package’s actual content.

SCEPTRE E27 Page13

Connecting the LED Monitor

If You have DVI Connection on Your Video Card…

1. Make sure the power of E27 LED MONITOR is turned off.

2. Obtain a DVI cable and connect to the DVI connection on your PC. Connect the other end of the cable to your E27 LED MONITOR.

3. Turn on the power of both the E27 LED MONITOR and the PC.

Please Note:

 Some video cards may have their DVI connection turned off by default. If you do not get video, please consult your video card’s technical support.

 The PC’s clearest picture is produced under 1920 x1080 at 60 Hz.

Page14 SCEPTRE E27

If You have VGA Connection on Your Video Card…

1. Make sure the power of E27 LED MONITOR is turned off.

2. If you were previously using a CRT (bulky) monitor, please hook up your old monitor first and make sure your refresh rate is set to 60 Hz frequency before using the

E27 LED MONITOR. You can find the refresh rate information and change it by RIGHT

CLICKING on the desktop with nothing selected. After you have right clicked, select the

PROPERTIES option. Click on the SETTINGS tab. Click on the ADVANCED button.

Click on the MONITOR tab. In that tab, change the refresh rate to 60 Hz and click on

APPLY. After the refresh rate changed, please shut down the computer and monitor.

3. Obtain the VGA cable and connect to the VGA connection on your PC. Connect the other end of the cable to your E27 LED MONITOR.

4. Turn on the power of both the E27 LED MONITOR and the PC.

Please Note:

 The PC’s clearest picture is ran with 1920 x1080 at 60 Hz.

SCEPTRE E27 Page15

If You have HDMI Connection on Your Cable or Satellite Box…

1. Make sure the power of the E27 LED MONITOR is turned off.

2. Obtain a HDMI cable and connect one end to the back of the monitor and the other end to the back of the cable or satellite box.

3. Turn on the power of both the E27 LED MONITOR and the cable or satellite box.

Please Note:

 Make sure to set audio output from your cable or satellite box to PCM output.

 Please refer to the cable or satellite company for more information.

Page16 SCEPTRE E27

On Screen Display (OSD) Menu

The OSD menu of the monitor provides various adjustments for the monitor such as color, brightness, contrast, and volume…..etc.

When you press the MENU button on the monitor, the OSD screen will appear. Select each of the functions with the UP or DOWN buttons. Use the MENU button again to enter each of the function or when you’re in the function already, use the MENU button to select the option you want to adjust. Use the UP or DOWN buttons to adjust each option’s values. When you want to exit press the EXIT button.

SCEPTRE E27 Page17

PICTURE SETTINGS

This function adjusts the brightness and contrast of the LCD.

1. To use this function, press MENU to open the OSD then highlight PICTURE SETTINGS function by pressing the UP or DOWN button.

2. Press MENU again to enter the function.

3. Press UP or DOWN button to select BRIGHTNESS or CONTRAST to adjust.

4. Press MENU to select the option you want to adjust.

5. Use the UP or DOWN button to adjust the values.

Please Note:

 BRIGHTNESS adjusts the black level in a picture. If the value is adjusted too high, the picture will look washed out. If too low, the picture will not have much detail in dark colors.

 CONTRAST adjusts the white levels in a picture. If the value is adjusted too high, the picture will not have any details in bright parts of the picture. If it sets too low, the picture will looked washed out.

 DCR is a function that automatically adjusts the contrast for you depending

on the graphics displayed at the time.

Page18 SCEPTRE E27

COLOR ADJUST

This function adjusts the overall balance of white colors in a picture in large increments. Color temperature consists of COOL, NORMAL, WARM, and USER COLOR.

1. To use this function, press MENU to open the OSD then highlight COLOR ADJUST function by pressing the UP or DOWN button.

2. Press MENU again to enter the function.

3. Press UP or DOWN button to select the option you want.

4. Press MENU to finalize your selection.

5. If you have selected USER, use the UP or DOWN button and the MENU button to adjust the values. a. COOL – This option adjusts the white balance towards the blue color giving the picture a bluish tint and cooler look. b. NORMAL – This option adjusts the white balance to give the picture a no biased white color. c. WARM – This option adjusts the white balance towards the red color giving the picture a reddish tint and warmer look. d. USER COLOR – This option lets the user adjust the white balance by tweaking the RED, GREEN, and BLUE color.

SCEPTRE E27 Page19

IMAGE

This function adjusts the image of the monitor.

1. Press MENU to open the OSD then highlight IMAGE by pressing the UP or DOWN buttons.

2. Press MENU to enter the function.

3. Press the UP or DOWN buttons to select the option you want to adjust and press MENU to enter the option.

4. Use the UP or DOWN buttons to adjust the values. a. AUTO ADJUST – This option automatically adjusts the image for you. b. H. POSITION – This option adjusts the horizontal position of the image. c. V. POISTION – This option adjusts the vertical position of the image. d. CLOCK – This option adjusts the picture clarity by large increments. e. PHASE – This option adjusts the picture clarity by small increments. f. SHARPNESS – This option adjusts the sharpness of the picture.

Please Note:

 Always use auto adjust first to adjust the image.

 This option is only available with a VGA connection. The image option will be disabled if you are using HDMI or DVI.

Page20 SCEPTRE E27

SIGNAL SOURCE

This function selects the source of the monitor.

1. Press MENU to open the OSD then highlight SIGNAL SOURCE by pressing the UP or

DOWN buttons.

2. Press MENU to enter the function.

3. Press the UP or DOWN buttons to select the source you want to change to.

SCEPTRE E27 Page21

OSD MENU

This function allows you to change the language of the OSD and adjust the OSD options.

1. Press MENU to open the OSD then highlight SETUP MENU by pressing the UP or DOWN buttons.

2. Press MENU to enter the function.

3. Press the UP or DOWN buttons to select the option you want to change to and press MENU to begin adjusting the option a. LANGUAGE – This option selects various languages for the OSD. b. OSD H. POSITION – This option changes the horizontal position of the OSD. c. OSD V. POSITION – This option changes the vertical position of the OSD. d. OSD TIMER – This option changes how long the OSD menu will stay up. e. TRANSLUCENCE – This option adjusts the transparency of the OSD menu.

Please Note:

 Changing the language of the OSD will alter all the messages and OSD language of the monitor.

Page22 SCEPTRE E27

MISC.

This function changes various miscellaneous options.

1. Press MENU to open the OSD then highlight MISC. by pressing the UP or DOWN buttons.

2. Press MENU to enter the function.

3. Press the UP or DOWN buttons to select the option you want to change to and press MENU to begin adjusting the option a. VOLUME – This option adjusts the volume of the speakers in the monitor. b. ALL RESET – This option resets all values in the OSD back to factory standard. c. SCALE – This option forces the picture into 16:9 or 4:3 mode. d. INFORMATION – This option shows the current video signal’s resolution and syncing frequency.

SCEPTRE E27 Page23

Supported PC Resolution

STD RESOLUTION & REFRESH RATE

VGA

VGA

720 x 400 @ 70Hz

640 x 480 @ 60Hz

VGA

VGA

SVGA

SVGA

SVGA

XVGA

XVGA

640 x 480 @ 75Hz

640 x 480 @ 72.8Hz

800 x 600 @ 60Hz

800 x 600 @ 72.2Hz

800 x 600 @ 75Hz

1024 x 768 @ 60Hz

1024 x 768 @ 70Hz

XVGA

SXVGA

SXVGA

1024 x 768 @ 75Hz

1280 x 1024 @ 60Hz

1280 x 1024 @ 75Hz

WXGA

WXGA+

1360 x 768 @ 60Hz

1440 x 900 @ 60Hz

WXGA+ 1660 x 900 @ 60Hz

WSXGA+ 1680 x 1050 @ 60Hz

WUXGA 1920 x 1080 @ 60Hz

Supported Video Resolution

VIDEO RESOLUTION

480p

720p

1080i

1080p

*Once a mode is optimized, there is no need to make any further adjustment as long as the VGA card remains unchanged. **Specifications are subject to change without notice.

Page24 SCEPTRE E27

Troubleshooting

Problem

DISPLAY IS UNCLEAR

AND UNSTABLE

THERE IS NO LED

DISPLAY or SCREEN

SAYS NO VIDEO

MONITOR SAYS

“SIGNAL OUT OF

RANGE”

I CAN’T OPEN THE

OSD

Possible solutions

To stabilize and clarify your display, use the AUTO ADJUST function or change the resolution to the display’s optimal setting 1920 X 1080 at

60Hz, then AUTO ADJUST.

Make sure you switched to the correct source. Check both sources to see video is on the other source. Check your video cable. It might be corrupt. Swap out the video cable for another one to see if the monitor will work. Check your power plug. See if it is fully plugged in on both the monitor and the wall.

If you have a CRT monitor, please connect the CRT monitor to the computer and change the refresh rate down to 60 Hz via your video card’s display settings menu. After the setting of 60 Hz has been change you can then use the LED on the computer.

1. To change the setting go to display settings by right clicking on your desktop with nothing selected. Choose the

PROPERTIES option.

2. Click on the SETTINGS tab, verify the resolution is NOT higher than 1920 x 1080, and click on the ADVANCED button.

3. Click on the MONITOR tab and change the refresh rate to

60 Hz.

4. Click on OK 2-3 times to finalize your change.

If you do NOT have a CRT monitor or it’s already broken, please make sure both the E27 LED monitor and your computer is turned off.

1. Turn on the LED monitor and the computer.

2. While the computer is turned on, press the “F8” key on your keyboard continuously until a selection menu appears and select the “Safe Mode” option.

3. When you’ve entered Safe Mode please uninstall any video card driver and monitor driver by using either the “Add /

Remove Programs” icon or going into “System

4. Properties” and manually removing anything under

“Monitors” and “Display Adapters”. After removing all the drivers, please reboot your computer and you should be able to see windows. Please install your monitor driver first, then your video card driver. Please remember to make sure your refresh rate should be at 60Hz.

You need to have a valid video signal going through the monitor before you can turn on the OSD.

SCEPTRE E27 Page25

Problem

I CANNOT GET THE

RESOLUTION

1920x1080

I DO NOT HEAR ANY

SOUND FROM THE

SPEAKERS

THE VIDEO IS TOO

BRIGHT NO MATTER

WHAT I ADJUST

THE WORDS AND

VIDEO ARE TOO

BLURRY

THE COLORS ARE

NOT CORRECT

Possible solutions

If you are using DVI, please try out VGA to see if you are able to achieve that resolution. If your VGA can then, your video card’s DVI cannot support widescreen resolutions.

Sometimes your video card will not read the monitor correctly and will not allow you to achieve the resolution you want. Rebooting your computer will solve the situation.

You can also make sure your video card’s video drivers are up to date.

You can find what video card you have by clicking on START then

RUN. Type in “DXDIAG”. When the diagnostic window pops up, click on the DISPLAY tab. The program will tell you what video chipset you have. Copy that name then search it with an online search engine like

GOOGLE™. Find your video card company’s web address and search for newer drivers. If updating your drivers does not work, you probably have one of the older video cards and cannot achieve a widescreen resolution. You’ll need to upgrade your video card to a newer one.

Check your 3.5 mm mini-jack cable and see if it is connected correctly between the computer and the monitor. Check the volume of your computer and also the volume of the monitor.

Sometimes having older video cards this type of problem might happen due to newer LEDs having to provide HD video capability and not being fully compatible with older video cards. You can try adjusting the contrast to a lower value and adjust the brightness to compensate.

Are you using the monitor’s native resolution? If not you’ll need to switch resolution to the native 1920 x 1080 at 60 Hz to make the words clearer. If you’re using VGA please do not forget to AUTO

ADJUST.

If the words are still blurry, please try enabling or disabling CLEAR

TYPE function from windows.

Sometimes the colors are not correct because your VGA or DVI cable is loose or corrupt. Please try reconnecting your cable or swap out your current cable to see if the problem persists.

HOW DO I RESET THE

MONITOR

Make sure there is a valid video signal to the monitor and press menu to open the OSD. Look for ALL RESET under MISC. options.

Page26 SCEPTRE E27

Problem

THE WORDS ARE TOO

SMALL AT 1920X1080

I DO NOT HEAR ANY

SOUND FROM THE

SPEAKERS WHEN

USING THE

(OPTIONAL) HDMI

PORT

I CAN’T GET TO THE

IMAGE OPTION

UNDER THE OSD

Possible solutions

At the native resolution of 1920x1080, some people might feel that the words are too small to read. You can change the size of the words in

Windows Operating System via its display properties.

For Windows XP

1. Right click on the background with nothing selected. Left click on the PROPERTIES option.

2. Click on the SETTINGS tab.

3. Under SETTINGS, click on the ADVANCED button.

4. Under GENERAL tab, change the size of the words by selecting the option NORMAL SIZE and change it to LARGE

SIZE.

5. Click on OK on all windows to exit.

6. Once you have finished rebooting, the computer is ready for use.

For Windows VISTA or Windows 7 or Windows 8

1. Right click on the Wallpaper. Left click on the

PERSONALIZE option.

2. Click on ADJUST FONT SIZE (DPI) option on the left column and

3. Click on CONTINUE.

4. In there you can change the size of the words by changing from the option DEFAULT SCALE to LARGE SCALE.

5. Click on APPLY to finalize your selection.

6. Once you have finished rebooting, the computer is ready for use.

The monitor only decodes PCM sound signals. Make sure your video device’s audio output is through HDMI and is outputting PCM sound format.

Make sure you are using a VGA video connection. If you have DVI or

HDMI, that option will be disabled because it only adjusts analog signals.

SCEPTRE E27 Page27

How do I clean the LED Monitor?

IMPORTANT

1. The power cable has to be removed from the socket before cleaning the LED Monitor.

2. Do not use volatile solvent (alcohol, rosin, and toluene) to clean the

LED Monitor. These types of chemicals might damage the housing and the LCD glass.

Cleaning the bezel

1. Use a 100% cotton cloth or micro-fiber cloth for cleaning.

2. If the bezel is dirty to the point where you cannot simply dry wipe it, please lightly dampen the wiping material with clean water and wipe again. Wipe the display with a dry micro-fiber cloth or 100% cotton cloth afterwards.

Please Note :

 Make sure you wring the water out of the cloth before cleaning the bezel in order to prevent water from penetrating into the electronics.

Cleaning the Screen

1. Use a 100% cotton cloth or micro-fiber cloth for cleaning.

2. The LCD screen glass is extremely fragile. Do not scrape it with any material. Do not press or tap the screen to avoid cracking. When the screen is dirty to the point where you cannot simply dry wipe it, please lightly dampen the wiping material with clean water and wipe again. Wipe the display with a dry micro-fiber cloth or 100% cotton cloth afterwards.

Page28 SCEPTRE E27

Specification

Display panel

Active Area / Screen Size

Aspect Ratio

Resolution

Brightness

Contrast

Response Time

Viewing Angle

Colors

LED Backlight

Dimension

Weight

Power input

VESA Hole Pattern

Diagonal 27 inches

Widescreen 16 : 9 (Default), 4:3

1920x1080

250 cd/m

2

1000:1 (NATIVE) 5,000,000:1 (DCR)

5ms (Gray to Gray)

Typical 170/160 Degree

(Horizontal/Vertical)

16.7M colors (RGB 6-bit+Hi_FRC)

25,000+ Hours

Monitor Display

With Stand: 25.63” x 8.62” x 17.68”

Without Stand: 25.63” x 2.09” x 17.40”

12.61 lb (with stand); 11.85 lb (without stand)

100 - 240V AC, 50/60 Hz. 1.1A (Max.)

100mm x 100mm (M4 x 6mm screws)

Features

I/O

SPEAKER OUTPUT

Compliance

VGA, DVI, HDMI (HDCP supported), AUDIO IN

2 Watt x 2

FCC, cTUVus, Energy Star, RoHS, MS WHQL,

ISTA 3A

Energy Star V6.0

*Specifications are subject to change without notice.

SCEPTRE E27 Page29

Call Us If You Need Help!

Products are often returned due to a technical problem rather than a defective product that may result in unnecessary shipping charges billed to you. Our trained support personnel can often resolve the problem over the phone or email.

For more information on warranty services or repairs after the warranty period, please contact our support department at the number below.

For technical help, contact our SCEPTRE Technical Support Group via email or phone. Please have your SCEPTRE Product Number (P/N), Serial Number

(S/N), and date of purchase available before you call.

Tech Support E-mail: [email protected]

Customer Service Email: [email protected]

TEL: 626-217-1022

Operation Hours: Mon - Fri at 8:30 AM – 5:30 PM (PST)

16800 East Gale Ave.

City of Industry, CA 91745

TEL : 626-369-3698

FAX : 626-855-5711

Website : www.SCEPTRE.com

Page30 SCEPTRE E27

LIMITED PRODUCT WARRANTY

Please read this warranty card carefully, it is a “ONE-YEAR LIMITED WARRANTY” on parts and labor and is only valid when purchased from an Authorized Reseller, only on new and non-refurbished product, and available to customers in the Continental US, Alaska, Hawaii and Puerto Rico. See below for the SCEPTRE Extended Service warranty.

SCEPTRE’s Responsibility

SCEPTRE Displays purchased in the United States are warranted to be free from defects in materials or workmanship for a period of one (1) year from the date of their original retail purchase. If the unit fails to conform to this warranty, we will service the monitor using new or refurbished parts.

Service Labor

During a period of one (1) year from the effective warranty date, SCEPTRE will provide, when needed, service labor to repair a manufacturing defect at SCEPTRE’s own Service Center. To obtain warranty service in the Untied States, you must first call our Customer Support at (800) 788-2878. The determination of service will be made by SCEPTRE Customer Support. PLEASE DO NOT

RETURN YOUR UNIT TO SCEPTRE WITHOUT PRIOR AUTHORIZATION.

Parts

New or remanufactured replacements for defective parts will be used for repairs by SCEPTRE at its designated Service Center for one (1) year from the effective warranty date. Such replacement parts are warranted for the remaining portion of the original warranty period.

Service

During the one (1) year warranty period, SCEPTRE will, at its option and sole discretion, repair or replace defective parts, including replacement of the entire Panel. The Customer will be required to ship the unit to the Service Center indicated at the time Customer Support is contacted to make the necessary repairs, you are responsible for all transportation charges to the service facility. SCEPTRE is NOT responsible for the de-installation or re-installation of the unit.

Packaging and Shipping Instruction

When you send the product to an authorized SCEPTRE service facility you must use the original carton box and packing material or an equivalent as designated by SCEPTRE.

Not Covered

This warranty does not cover defects, malfunctions or failures resulting from shipping or transit accidents, abuse, misuse, operation contrary to furnished instructions, operation on incorrect power supplies, operation with faulty associated equipment, modification, alteration, improper servicing, tampering or normal wear and tear or Monitors on which the serial number has been removed or defaced. Image Sticking caused by operating at excessive brightness levels for extended periods or mishandling are not covered by this warranty.

ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED IN

DURATION TO THE PERIOD OF TIME SET FORTH ABOVE. OUR LIABILITY FOR ANY AND ALL

LOSSES AND DAMAGES RESULTING FROM ANY CAUSE WHATSOEVER, INCLUDING OUR

NEGLIGENCE, ALLEGED DAMAGE OR DEFECTIVE GOODS, WHETHER SUCH DEFECTS ARE

DISCOVERABLE OR LATENT, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE

DISPLAY. WE SHALL NOT BE RESPONSIBLE FOR LOSS OF USE, COMMERCIAL LOSS OR

OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW

SCEPTRE E27 Page31

LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR

LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS

OR EXCLUSIONS MAY NOT APPLY TO YOU. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. This is the only warranty applicable; no one is authorized to extend or modify it or to grant any other warranty.

SCEPTRE retains the right to assess all warranty claims and to determine if damages are covered by the warranty. In case of a claim that is not covered by the warranty, you will be contacted to determine whether SCEPTRE should repair the damage for a fee or whether the product should be returned to you as received by the repair center.

Dead Pixel Policy

SCEPTRE sets limit on the LCD at 3 dead pixels in a cluster adjacent to each other, or 5 dead pixels in a combination of color and brightness. Any number of dead or bad pixels under the limit is considered to be within normal performance specification of the LCD and is not considered defective.

Owner’s Responsibility

Effective Warranty Date

Warranty begins on the date of sale to the end user. To ensure warranty service, keep the dated bill or sale receipt as evidence of the purchase date. If you can no longer obtain your receipt, the warranty will revert to the unit’s manufacture date according to the serial number of the unit. This limited warranty applies only to the original purchaser and is non-transferable.

Warranty Service

For warranty service information, contact SCEPTRE Technical Support at email address

[email protected]

, via phone at (800) 788-2878, or via World Wide Web chatting service at www.Sceptre.com

. SCEPTRE Technical Support is available Monday to Friday 8:30 AM to 5:30 PM

Pacific Time. Parts and service labor that are SCEPTRE’s responsibility (see above) will be provided without charge. Other services or services not covered by the warranty are at the owner’s expense.

You must provide the model, serial number and date of purchase. Before you ask for warranty service, read your User Manual. You might avoid a service call.

Warranty conditions are subject to change, for latest Warranty Terms and Conditions and additional information regarding your warranty, please see complete details online at www.SCEPTRE.com

.

Page32 SCEPTRE E27

Disclaimer & Copyright Information

Microsoft, Windows are registered trademarks of Microsoft Corporation in the

United States and other countries.

This Monitor meets the ENERGY STAR® guidelines under the default setting. Changing this setting or enabling other options will increase power consumption which could possibly exceed the guidelines of

ENERGY STAR®. For more information on the ENERGY STAR program, please refer to www.energystar.gov

.

“HDMI, the HDMI logo and High-Definition Multimedia

Interface are trademarks or registered trademarks of HDMI

Licensing LLC.”

HDCP is a trademark or registered trademark of Digital Content Protection, LLC.

Sceptre, Inc. shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or use of this product.

In the interest of continuing product improvement, Sceptre, Inc. reserves the right to change product specifications without notice. Information in this document may change without notice.

No part of this document may be copied, reproduced, or transmitted by any means, for any purpose without prior written permission from Sceptre, Inc..

SCEPTRE is a trademark or registered trademark of Sceptre Group.

SCEPTRE E27 Page33